Yamaha v4 Руководство пользователя

Бренд: Yamaha

Модель: v4

Тип: Руководство пользователя

R Remote Version 4.5 User’s Guide 1

R Remote Version 4.5 User’s Guide

Thank you for choosing a Yamaha product.

This user’s guide explains setup, firmware update and use of "R Remote," a Windows/Mac application that lets

you make parameter settings for the Rio3224-D/Rio1608-D/Ri8-D/Ro8-D/RSio64-D/RMio64-D/Rio3224-

D2/Rio1608-D2 (subsequently "R series") and the Tio1608-D units.

This application lets you edit the parameters of up to twenty four devices from a single computer. Even if the

device is not connected, you can mount it virtually and edit its settings beforehand.

Up to two computers in which R Remote is installed can be connected to a single device. This means, for

example, that the main operator could operate a console such as the CL while two assistants make detailed

adjustments at the other locations.

■ NOTICE

⠂ Yamaha Corporation owns exclusive copyrights for the R Remote, the firmware for each device, and the user’s guide.

⠂ It is prohibited to duplicate or modify the firmware, software or manuals, in part or in their entirety, without permission from the copyright

owner.

⠂ The illustrations and screens as shown in this User’s Guide are for instructional purposes, and may appear somewhat different from the

screens which appear on your computer.

⠂ This software was not produced with the intention to support touch-panel operation in Windows 8.1 / Windows 10, so we cannot

guarantee operation if a touch-panel is used.

⠂ Dante is a trademark of Audinate.

⠂ Windows is a registered trademark of Microsoft ® Corporation in the United States and other countries.

⠂ Mac and macOS are trademarks of Apple Inc., registered in the U.S. and other countries.

⠂ The company names and product names in this document are the trademarks or registered trademarks of their respective companies.

⠂ This guide predominantly uses screenshots of Windows. However, Mac screenshots are used when instructions of the function apply

only to the Mac.

⠂This product incorporates open source software. For information about the software, refer to the “License Agreement,” accessed from

the “Legal” button on the “About R Remote” window.

⠂ Software may be revised and updated without prior notice.

R Remote Version 4.5 User’s Guide 2

Contents

■ NOTICE ............................................................................................................................................................... 1

Using the PDF manual ............................................................................................................................................. 4

System Requirements .............................................................................................................................................. 4

Operation ................................................................................................................................................................. 4

Setup ............................................................................................................................ 5

Install (or uninstall) the R Remote ............................................................................................................................ 5

Set on the devices ................................................................................................................................................... 6

UNIT ID

............................................................................................................................................................................ 6

IP address

....................................................................................................................................................................... 6

Connection ....................................................................................................................................................................... 7

START UP MODE

............................................................................................................................................................ 8

Connect the computer and the devices .................................................................................................................. 9

Power-on the devices .............................................................................................................................................. 9

Specify the computer's IP address ....................................................................................................................... 10

For Windows ................................................................................................................................................................... 10

For Mac ........................................................................................................................................................................... 12

Use Dante Controller or the CL/QL series console to specify the routing

................................................................ 12

Operating R Remote ................................................................................................... 13

Menu bar................................................................................................................................................................ 13

Areas of the screen ............................................................................................................................................... 14

Device Selection Area .................................................................................................................................................... 15

Information Display Area ................................................................................................................................................ 15

Main Area ....................................................................................................................................................................... 16

Edi

t window .................................................................................................................................................................... 18

“Network Setup” dialog box .................................................................................................................................. 28

“Device Information” dialog box ............................................................................................................................ 29

“IP Address” dialog box ........................................................................................................................................ 30

“Properties” dialog box .......................................................................................................................................... 31

Updating the Firmware ............................................................................................... 32

Precautions ............................................................................................................................................................ 32

Updating – Operation Overview ............................................................................................................................ 32

Connecting the Computer to the Device ............................................................................................................... 33

Network Settings .................................................................................................................................................... 34

R Remote Firmware Updater ................................................................................................................................. 34

Update operation ................................................................................................................................................... 36

Detecting the device ............................................................................................................................................. 36

In case of failure in updating the firmware ............................................................................................................ 36

Messages .............................................................................................................................................................. 39

■ Error messages .......................................................................................................................................................... 39

■ Warning Messages ....................................................................................................................................................

■ Confirmation Messages ............................................................................................................................................. 39

R Remote Version 4.5 User’s Guide 3

■ Other Messages ......................................................................................................................................................... 40

Troubleshooting .......................................................................................................... 41

Decimal/hexadecimal conversion table ................................................................................................................ 43

R Remote Version 4.5 User’s Guide 4

Using the PDF manual

 You can move to the corresponding page by clicking on links in the table of contents or in the text.

 If you want to find information on a specific topic, function or feature, select “Find” or “Search” from the

Adobe Reader “Edit” menu and enter a key word to locate the related information anywhere in the

document.

 You can also click on desired items and topics you want to refer to in the “Bookmarks” index to the left of

the main display window, and jump to the corresponding page. (Click the “Bookmarks” tab to open the

index if it is not displayed.)

System Requirements

In order to use R Remote, you'll need the following items.

● A computer equipped with the following conditions:

Windows 7 SP1 Home Premium or later, Windows 8.1, Windows 10

(R Remote supports both 32-bit and 64-bit Windows.)

OS X 10.9.5, OS X 10.10.x, OS X 10.11.x, macOS 10.12.x, macOS 10.13.x

CPU

Intel Core i3 or higher

HDD

120MB or more

Supported Devices (*)

Rio3224-D, Rio1608-D, Ri8-D, and Ro8-D (firmware V3.11 or later)

RSio64-D (firmware V1.00 or later)

RMio64-D (firmware V3.11 or later)

Tio1608-D, Rio3224-D2, and Rio1608-D2 (firmware V1.00 or later)

Others



An Ethernet connector (1000BASE-T or higher recommended)

 Ethernet cable (CAT5e or better)

 Network switch (with gigabit Ethernet support), when connecting devices

via a Dante network

 Dante Controller must be installed. (**)

(*) When the firmware version of the target device is out-of-date and unsupported, you will need to update

the firmware by using exclusive update software for each product.

(**) You can download Dante Controller from the download page of the following website.

https://www.yamaha.com/proaudio/

The Mini

mum System Requirements described above are applied to the R Remote version 4.5.0. Keep in mind

that the software is often updated and the system requirements are subject to change. You can check the

latest version information of each program and its system requirements at the following website

https://www.yamaha.com/proaudio/

Operation

Keyboard Shortcuts

<Windows modifier key> (<Mac modifier key>) + <key> or click shows the shortcut keys. For example, <Ctrl>

(<command>) +click means “press <Ctrl> under Windows or <command> under Mac, then click.”

Right Click

On Mac click while holding down the <control> key.

R Remote Version 4.5 User’s Guide 5

Setup

The setup workflow is shown below.

Install the R Remote

Set on the devices

Connect the computer and the devices

You cannot control the parameters of the device connected from another subnet via

DANTE DOMAIN MANAGER.

Power-on the devices

Specify the computer's IP address

Use Dante Controller or the CL/QL series console to specify the routing

For details on connections and settings for the devices, refer also to the owner's manual of your devices.

Install (or uninstall) the R Remote

The installation procedure is as follows.

Logon to Windows or Login to Mac with administer account.

After decompressing the downloaded file, double-click “setup.exe” (Windows) or “Install R Remote

Vxxx.pkg” (Mac)(xxx is version) in the decompressed file location.

The R Remote setup wizard will appear.

Under Windows, the “User Account Control” dialog box may appear.

Click [Continue] or [Yes].

Proceed with the installation as directed by the instructions in the screen.

To uninstall the software (remove the application),

Windows:

In Control Panel, click [Programs and functions] or [Uninstall a program], then select the item you want to

uninstall, and click [Uninstall or change].

A dialog box will appear; follow the instructions in the screen to uninstall the software.

If the “User Account Control” dialog box appears, click [Continue] or [Yes].

Mac:

Double-click "Uninstall R Remote.app" which is included in the installer.

R Remote Version 4.5 User’s Guide 6

Set on the devices

Set the DIP switches and [UNIT ID] rotary switch of the unit, taking note of the following settings.

On the Rio3224-D2 and Rio1608-D2, set the following settings using the front panel display of the device.

UNIT ID

 Set a unique UNIT ID that will not conflict with the other device, over a range of 1 to 24 (hexadecimal 18). R

Remote will not detect units with a setting of 0 or 25 or higher. (For details on converting between decimal

and hexadecimal, refer to the "Decimal/hexadecimal conversion table" on page 43)

 Rio3224-D2 and Rio1608-D2: Set the “UNIT ID” on the SETUP menu.

 For devices excepting the Rio3224-D2 and Rio1608-D2: Set the DIP switches to the following combinations.

Settings

Switch

UNIT ID ranging from 1 to F

(decimal values 1 to 15)

(1 up)

UNIT ID ranging from 10 to 18

(decimal values 16 to 24)

(1 down)

IP address

Specify the IP address that the R Remote uses for control.

(The IP address set here is different from the IP address of the Dante network.)

For devices other than the Tio1608-D, the RMio64-D, the Rio3224-D2 and the Rio1608-

Settings

Switch

Auto IP

(The IP address will be automatically set to 169.254.xxx.xxx.)

(2 and 3 up)

DHCP

(The IP address assigned by the DHCP server will be used.)

(2 down, 3 up)

Static IP (Auto)

[The IP address will be set to 192.168.0.xxx (xxx= UNIT ID).]

(2 up, 3 down)

Static IP (Manual)

(Set the IP address to the value specified on the R Remote)

(2 and 3 down)

The first time that you connect an R series unit to your computer, set this to something other than Static IP

(Manual). If you want to use the Static IP (Manual) setting, first specify the IP address on the R Remote and

then switch to Static IP (Manual).

If the network consists only of Dante devices and R Remote, we recommend that you use the Auto IP

setting.

If you are connecting to an existing network, select DHCP as needed.

If you want to use zoning to set the IP address, or want to connect to an existing network but use a static IP

address, choose Static IP (Manual) and use the R Remote to set the IP address.

R Remote Version 4.5 User’s Guide 7

Tio1608

-D

Settings

Switch

Auto IP (Link Local)

(The IP address will be automatically sets to 169.254.xxx.xxx.)

(5 and 6 up)

DHCP

(The IP address assigned by the DHCP server will be used.)

(5 up, 6 down)

Static IP (Auto)

[The IP address will be set to 192.168.0.xxx (xxx= UNIT ID).]

(5 down, 6 up)

Static IP (Manual)

(Set the IP address to the value specified on the R Remote)

(5 and 6 down)

RMio64-D

The IP address is set by using the R Remote since RMio64-D has no DIP switches for setting the IP address.

Refer to the “IP Address” dialog box for more information.

Rio3224

-D2-D and Rio1608-D2

Set the “NETWORK MODE” in the SETUP menu.

Connection

For devices other than the RMio64-D, the Rio3224-D2 and the Rio1608-D2

Settings

Switch

DAISY CHAIN

(4 up)

REDUNDANT

(4 down)

RMi

o64-D

Rio3224-D2-D and Rio1608-D2

Set the “SECONDARY PORT” in the SETUP menu.

Settings

Switch

DAISY CHAIN

(1 up)

REDUNDANT

(1 down)

R Remote Version 4.5 User’s Guide 8

START UP MODE

If a C

L/QL series unit is not connected, we recommend that you set START UP MODE to RESUME. If this is

set to REFRESH, settings must be transmitted from the R Remote each time the R series unit is restarted.

Rio3224-D, Rio1608-D, Ri8-D and Tio1608-D

Settings

Switch

REFRESH

When the device is turned on, the following settings are initialized and

inputs/outputs are muted.

・HA GAIN (-6 dB)

・+48V (OFF)

・HPF (OFF)

・HPF FREQ (80Hz)

・Gain Compensation (OFF) (Except for Tio1608-D)

To use the device after initialization, you need to: turn the

device off  set the DIP switches to RESUME turn the device on.

(7 and 8 up)

RESUME

(The unit starts up using the settings assigned prior to the most recent

power off.)

(7 down, 8 up)

RSi

o64-D

Settings

Switch

NORMAL

(Start up normally with the settings of the previous start-up.)

(7 and 8 up)

INITIALIZE

The following settings are initialized when the device is turned on.

・SLOT 1-4 SRC (OFF)

・WORD CLOCK SELECT (DANTE/48kHz)

・USER PATTERN (same routing configuration as the preset PATTERN # 1)

・Static IP (Manual) (0.0.0.0)

・PANEL LOCK (Unlock)

・Dante PATCH (All OFF)

・Dante DEVICE LABEL (Y001-Yamaha-RSio64-D-123456) (*1)

To use the device after initialization, you need to: turn the

device off



set the DIP switches to NORMAL



turn the device on.

(7 down, 8 up)

(*1) The third and fourth characters of the Dante DEVICE LABEL depend on the device settings of DIP switch 1 and the

SETUP [UNIT ID] rotary switch. The lower six digits depend on the lower six digits of the unit’s MAC address.

R Remote Version 4.5 User’s Guide 9

Rio3224

-D2-D and Rio1608-D2

Set the “START UP MODE” in the SETUP menu.

Settings

REFRESH

When the device is turned on, the following settings are initialized and inputs/outputs are muted.

・HA GAIN (-6 dB)

・+48V (OFF)

・HPF (OFF)

・HPF FREQ (80Hz)

・GAIN COMPENSATION (OFF)

・

COMPENSATION GAIN (-6 dB)

RESUME

(The unit starts up using the settings assigned prior to the most recent power off.)

REFRESH w/o MUTE

(The settings are initialized when turned the device on. The initial values are the same as for REFRESH.

However, inputs and outputs are not muted.)

Connect the computer and the devices

Use an Ethernet cable to connect the computer and the devices.

If you selected DAISY CHAIN in “SECONDARY PORT” on the above, connect the Dante connectors of the

devices in a daisy chain to the computer.

If you selected REDUNDANT in “SECONDARY PORT” on the above, connect the computer to the network

switch that is connected to the Dante [PRIMARY] connector.

You cannot control the parameters of the device connected from another subnet via DANTE DOMAIN

MANAGER.

Power-on the devices

Power-on the devices. The DIP switch settings, the rotary switch settings and the settings in the SETUP menu

after power-on will not be applied until the next power-on.

R Remote Version 4.5 User’s Guide 10

Specify the computer's IP address

Specify the computer's IP address so that it can communicate with the devices.

The method of making this setting depends on whether you're using Windows or Mac. Also, the computer's IP

address setting will differ depending on the IP address specified in "Set on the devices."

If you're using Mac, click the link.

For Windows

Accessing the Control Panel

The way to access the Control Panel will depend on your operating system.

* Windows 7

Select [Start]  [Control Panel].

* Windows 8.1/Windows 10

Right click [Start]  [Control Panel].

TCP/IP Settings

Make TCP/IP settings for the computer as follows.

1. Access the Control Panel, then click or double-click [Network and Sharing Center] or [View network

status and tasks].

The “Network and Sharing Center” is displayed.

2. Click [Manage network connection] or [Change adapter settings] from the “Tasks” list located in

the left side of “Network and Shearing Center” window, then double-click [Local Area Connection].

The “Local Area Connection Status” dialog box will be displayed.

・The “User Account Control” dialog box may appear. Click [Continue] or [Yes].

・If the “Local Area Connection properties” dialog box appears, skip ahead to step 4.

3. Click [Properties].

The “Local Area Connection properties” dialog box will be displayed.

The “User Account Control” dialog box may appear. Click [Continue] or [Yes].

4. Select [Internet Protocol Version 4(TCP/IPv4)], then click [Properties].

The “Internet Protocol Version 4(TCP/IPv4) Protocol” dialog box will be displayed.

R Remote Version 4.5 User’s Guide 11

5. Make the following settings according to the IP address setting you made in "Set on the devices."

Auto IP or DHCP

Static IP (Auto)

Click [Obtain an IP address automatically]. Click [Use the following IP address:].

As the IP address, enter "192.168.0.xxx (a value in the

range 1 to 254 that does not conflict with any other

device, including the target devices), and enter

"255.255.255.0" as the subnet mask.

The 192.168.0.101 shown below is an example.

If you're using Static IP (Manual), specify the setting that's appropriate for your network. For details,

consult your network administrator.

6. Click [OK].

Proceed to "Use Dante Controller or the CL/QL series console to specify the routing."

R Remote Version 4.5 User’s Guide 12

For Mac

Make TCP/IP settings for the computer as follows.

1. Click [System Preferences][Network].

The “Network” dialog box will be displayed.

2. Click the service that you want to connect to the device.

If you're using the Ethernet port that's built into the Mac, click [Ethernet].

3. Make the following settings according to the IP address setting you made in "

Set on the devices

Auto IP or DHCP

Static IP (Auto)

In "Configure IPv4," choose [Using DHCP].

In “Configure IPv4,” choose [Manually]. As the IP

address, enter "192.168.0.xxx (a value in the range 1 to

254 that does not conflict with any other device,

including the target devices), and enter "255.255.255.0"

as the subnet mask.

The 192.168.0.101 shown below is an example.

If you're using Static IP (Manual), specify the setting that's appropriate for your network. For details,

consult your network administrator.

4. Click [Apply] button, then close “Network” dialog box.

Use Dante Controller or the CL/QL series console to specify the routing

If you're using Dante Controller to specify the routing, refer to "Dante Controller User’s Guide."

If you're using a CL/QL series console to specify the routing, refer to the each Reference Manual.

This completes the setup.

R Remote Version 4.5 User’s Guide 13

Operating R Remote

Start R Remote.

Windows 7/Windows 10 users: click [Start][All Programs][Yamaha R Remote][R Remote]

Windows 8.1 users: in the "Start screen," double-click the [R Remote] tile.

Mac users: click [Go][Applications] double-click [R Remote].

 When you start R Remote, the “Network Setup” dialog box may appear, allowing you to select the

computer's network card that will be used for communication with the devices. If this appears, click the

network card that is connected to the device, and then click the [Apply] button.

 For R Remote for Windows 8.1, depending upon user access privileges, the software's "Tile(icon)" may not

appear on the "Start screen". In such cases, you can find the software icon in "Apps" by the following steps:

1. Right-click anywhere on Start screen.

2. Click "All apps" button at the bottom right side of Start screen.

Menu bar

The commands that can be executed by R Remote can be found here, grouped by category.

Click here to see a list of commands.

Command

Summary

Dialog box that appears

[File] [Open] Opens a previously-saved file (rrmt

format or rrm format).

NOTICE

If you open the file when devices are

connected, the settings will be

applied to the devices

. Be aware that

if a CL/QL series console is also

connected, its settings will be

overwritten.

“Open File” dialog box

[Save As]

Saves the file. It will have a file name

extension of rrmt, and will be usable

only by R Remote.

“Save File” dialog box

[Network Setup]

Selects the computer’s network

adapter that will be used to

communicate with the devices.

“Network Setup” dialog box

[Device Information]

Displays information about the

devices that are connected.

“Device Information” dialog box

[Quit] *1

Quits R Remote.

---

[Tool]

[Firmware Update]

Calls up the window to update the

firmware.

R Remote Firmware Updater

[About] *1

[About R Remote]

Displays details such as the software

version of R Remote.

“

About R Remote” dialog box

*1 Mac users: [Quit] and [About] are located in the R Remote menu.

R Remote Version 4.5 User’s Guide 14

Areas of the screen

The R Remote screen is broadly divided into three areas: the Device Selection Area, the Information Display

Area, and the Main Area.

R Remote Version 4.5 User’s Guide 15

Device Selection Area

When you click a display switching button, the corresponding device is shown in the

information display area and in the main area.

With a display switching button selected, pressing the left mouse button makes all indicators

of the corresponding device blink, allowing you to identify the corresponding unit.

Also shows an attention icon depending on the device status.

When you right-click a display switching button, the following context menu appears.

Command

Summary

[Mount] Opens the "Mount" window. Select the device that you want to mount.

[Connect]

Synchronizes with the selected device.

[Disconnect]

Disconnects from the selected device.

[Properties]

Open the “Properties” dialog box.

[Summary]

(Rio3224-D2 and Rio1608-D2 only)

Displays the selected device summary (REPORT).

[Log]

(Rio3224-D2 and Rio1608-D2 only)

Save the device log. The file is named automatically according the following format.

In case of Rio3224-D2: Rio3224-D2_201712261339.log

* The numbers after “_” indicate the year, month, day and time.

The connection status is shown below each display switching button.

Indication

Status

VIRTUAL The device is mounted without the existence of the actual device.

Alternately, communication is impossible due to incorrect settings having been

made.

BLANK

The device is not powered-on or the device is not connected to the computer.

CONNECTED

Currently synchronized with the device.

DISCONNECTED Synchronization with the device is possible, but is currently disconnected by the

[Disconnect] command. Alternatively, communication has been interrupted, or

connection failed.

DUPLICATED More than one device of the same UNIT ID exists. Eliminate any UNIT ID conflict

between devices.

Information Display Area

This area shows the UNIT ID and name of the selected device.

To check the firmware version or IP address, choose [File] menu -> [Device Information] to open the “Device

Information” dialog box.

R Remote Version 4.5 User’s Guide 16

Main Area

This area shows the state of the selected device and allows basic parameter editing. The display depends on

the model.

For Rio3224-D / Rio1608-D / Ri8-D / Tio1608-D / Rio3224-D2 / Rio1608-D2

The screen is explained here using the Rio3224-D as an example. The number of items in the HA display area

differs depending on the model.

The Edit window opens if you double-click or right-click and choose [Open Edit Window] anywhere other than

on a controller.

① HA display area

Her

e you can view and edit HA settings for the Rio3224-D / Rio1608-D / Ri8-D / Tio1608-D / Rio3224-D2 /

Rio1608-D2 unit.

If you press the left mouse button on an area that shows the device's jack number, the indicator of the

actual device's corresponding jack will light.

a. [+48V] button

Turns phantom power on/off for each channel.

b. GAIN knob

Specifies the analog gain for the HA of the device. The current setting is shown in the numeric box

located below the knob.

You can double-click a numeric value box and enter a value directly from the keyboard.

The level meter located at thes immediate right of the knob indicates the input level of the

corresponding port.

On the knobs, you can use the following shortcuts and context menu.

Action

Operation

<Ctrl> (<command>) + click

Sets analog gain to the default value (-6 dB).

<Ctrl> (<command>) + <Shift> + click

Sets the analog gain to 0 dB.

R Remote Version 4.5 User’s Guide 17

Action

Operation

Right click Displays the following context menu.

[All Default]

Sets the analog gain of all channels to the default

value (-6 dB).

[All 0dB]

Sets the analog gain of all channels to 0 dB.

c. [HPF] button

This is an on/off switch for the high-pass filter that is built into the HA of the device. To specify the

cutoff frequency, make settings in the Edit window.

② [+48V MASTER] indicator

Indicates the master phantom power on/off status for the device (the on/off setting is switched on the

device itself).

③ [SYSTEM] indicator / [SYNC] indicator

Indicates the status of the device or the Dante status. When you move the mouse cursor to this area, the

display content appears as a popup. Also shows an information icon or attention icon depending

on the device status.

④ [PEAK HOLD] button

If this button is on, the peaks of each level meter are held. When you turn this off, the peaks that had

been held are cancelled.

R Remote Version 4.5 User’s Guide 18

Edit window

This appears if you double-click in the main area other than on a controller, or if you right-click and choose

[Open Edit Window].

Here you can view and edit detailed HA settings for the device. To close the window, click the [x] button in the

upper right if you're using Windows, or click the [x] button if you're using Mac.

The screen is explained here using the Rio3224-D as an example. The number of Port select tabs differs

depending on the model.

① Device name

Shows the UNIT ID number and name of the device.

② [PEAK HOLD] button

If this button is on, the peaks of each level meter are held. When you turn this off, the peaks that had

been held are cancelled.

③ Port select tab

For the Rio3224-D, Rio1608-D, Rio3224-D2 or Rio1608-D2, these tabs switch the ports that are shown.

④ Port index

Indicates the port number of the device. When you press this with the left mouse button, the indicator of

the corresponding port of the device will light.

⑤ [+48V] button

Turns the HA phantom power on/off.

⑥ [A.GAIN] knob

Specifies the analog gain for the HA of the device. The current setting is shown in the numeric box

located below the knob.

You can double-click a numeric value box and enter a value directly from the keyboard.

The level meter located at the immediate right of the knob indicates the input level of the corresponding

port.

R Remote Version 4.5 User’s Guide 19

On the k

nobs, you can use the following shortcuts and context menu.

Action

Operation

<Ctrl> (<command>) + click

Sets analog gain to the default value (-6 dB).

<Ctrl> (<command>) + <Shift> + click

Sets analog gain to 0 dB.

Right click Displays the following context menu.

[All Default]

Sets the analog gain of all channels to the default value (-6

dB).

[All 0dB]

Sets the analog gain of all channels to 0 dB.

⑦ [GC] button

Switches on/off the gain compensation that regularizes the signal level on the audio network. If this is on,

the gain value fixed by gain compensation is displayed, and subsequent changes to analog gain is

compensated by the compensation gain within the device; audio is transmitted to the Dante network at

the gain value that was fixed immediately before this was enabled.

There are limits to the amount of gain compensation. The maximum compensation is 24 dB when turning the knob

toward the left, and 48 dB when turning the knob toward the right. For example if you apply gain compensation at 30

dB, compensation is maintained until you set the analog gain to 6 dB, but if you set the analog gain to 4 dB, the gain

value that is output will be 28 dB. If in this state you return the setting to 6 dB or higher, compensation maintains the

level at 30 dB.

⑧ [FREQ] knob / [HPF] button

Switches on/off the high-pass filter that is built into the HA of the device, and adjusts the cutoff frequency.

The current setting is shown in the numeric box located below the knob.

If you <ctrl> (<command>) + click above the [FREQ] knob, the cutoff frequency is set to the default

value (80 Hz).

R Remote Version 4.5 User’s Guide 20

For Ro8-D

The Ro8-D has no settings that can be operated, so only the [SYSTEM] indicator and [SYNC] indicator are

shown.

① [SYSTEM] indicator / [SYNC] indicator

Indicates the status of the device or the Dante status. When you move the mouse cursor to this area, the

display content appears as a popup. Also shows an information icon or attention icon depending

on the device status.

Страница загружается ...

Yamaha v4 Руководство пользователя

Бренд: Yamaha

Модель: v4

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha v4 User guide
français: Yamaha v4 Mode d'emploi
italiano: Yamaha v4 Guida utente
español: Yamaha v4 Guía del usuario
Deutsch: Yamaha v4 Benutzerhandbuch
Nederlands: Yamaha v4 Gebruikershandleiding
português: Yamaha v4 Guia de usuario
dansk: Yamaha v4 Brugervejledning
polski: Yamaha v4 instrukcja
čeština: Yamaha v4 Uživatelská příručka
svenska: Yamaha v4 Användarguide
Türkçe: Yamaha v4 Kullanici rehberi
suomi: Yamaha v4 Käyttöohjeet
română: Yamaha v4 Manualul utilizatorului

Yamaha v4 Руководство пользователя

Yamaha v4 Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов