Yamaha V3 Руководство пользователя

R Remote Version 3 User’s Guide 1

R Remote Version 3

User’s Guide

Thank you for choosing a Yamaha product.

This user’s guide explains setup and use of "R Remote," a Windows/Mac application that lets you

make parameter settings for the Rio3224-D/Rio1608-D/Ri8-D/Ro8-D/RSio64-D/RMio64-D

(subsequently "R series") units.

This application lets you edit the parameters of up to twenty four R series units from a single

computer. Even if the R series unit is not connected, you can mount it virtually and edit its settings

beforehand.

Up to two computers in which R Remote is installed can be connected to a single device. This means,

for example, that the main operator could operate a console such as the CL while two assistants make

detailed adjustments at the other locations.

R Remote Version 3 User’s Guide 2

■

NOTICE

・ Yamaha Corporation owns exclusive copyrights for the R Remote, and the user’s guide.

・ It is prohibited to duplicate or modify the firmware, software or manuals, in part or in their

entirety, without permission from the copyright owner.

・ The screen displays as illustrated in this User Guide are for instructional purposes, and may

appear somewhat different from the screens which appear on your computer.

・ This software was not produced with the intention to support touch-panel operation in Windows 8

/ Windows 8.1, so we cannot guarantee operation if a touch-panel is used.

・ Dante is a trademark of Audinate.

・ Windows is a registered trademark of Microsoft ® Corporation in the United States and other

countries.

・ Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries.

・ The company names and product names in this document are the trademarks or registered

trademarks of their respective companies.

・ This guide predominantly uses screenshots of Windows. However, Mac screenshots are used when

instructions of the function apply only to the Mac.

・ Software may be revised and updated without prior notice.

R Remote Version 3 User’s Guide 3

Contents

■

Using the PDF manual

............................................................................................................................. 4

■ System Requirements

.............................................................................................................................. 4

Operation .................................................................................................................................................... 4

■ Setup

.......................................................................................................................................................... 5

Install the R Remote .................................................................................................................................. 5

Set on the R series units ............................................................................................................................ 6

For Rio3224-D / Rio1608-D / Ri8-D ....................................................................................................... 6

For RSio64-D ........................................................................................................................................... 7

For RMio64-D .......................................................................................................................................... 8

Connect the computer and R series units ................................................................................................. 9

Power-on the R series units ....................................................................................................................... 9

Specify the computer's IP address ........................................................................................................... 10

For Windows .......................................................................................................................................... 10

For Mac .................................................................................................................................................. 12

Use Dante Controller or the CL/QL series console to specify the routing ........................................... 12

■

Operating R Remote

............................................................................................................................... 13

Menu bar ................................................................................................................................................... 13

Areas of the screen ................................................................................................................................... 14

Device Selection Area ............................................................................................................................... 15

Information Display Area ........................................................................................................................ 15

Main Area .................................................................................................................................................. 16

For Rio3224-D / Rio1608-D / Ri8-D ..................................................................................................... 16

For Ro8-D .............................................................................................................................................. 20

For RSio64-D ......................................................................................................................................... 21

For RMio64-D ........................................................................................................................................ 25

“Network Setup” dialog box ..................................................................................................................... 27

“Device Information” dialog box .............................................................................................................. 28

“IP Address” dialog box ......................................................................................................................... 29

“Properties” dialog box ............................................................................................................................. 30

■

Uninstalling the software(Removing the application)

......................................................................... 31

■

Troubleshooting

...................................................................................................................................... 32

Decimal/hexadecimal conversion table ................................................................................................... 34

R Remote Version 3 User’s Guide 4

■ Using the PDF manual

・You can move to the corresponding page by clicking on links in the table of contents or in the text.

・If you want to find information on a specific topic, function or feature, select “Find” or “Search” from

the Adobe Reader “Edit” menu and enter a key word to locate the related information anywhere in the

document.

・You can also click on desired items and topics you want to refer to in the “Bookmarks” index to the

left of the main display window, and jump to the corresponding page. (Click the “Bookmarks” tab to

open the index if it is not displayed.)

■

System Requirements

In order to use R Remote, you'll need the following items.

● A computer equipped with the following conditions:

OS

Windows 7 SP1 Home Premium or later, Windows 8, Windows 8.1

(R Remote supports both 32-bit and 64-bit Windows.)

Mac OS X 10.9.5, 10.10.x

CPU

Intel Core i3/i5 or higher

HDD

120MB or more

Connector

An Ethernet connector (1000BASE-T or higher recommended)

Others Dante Controller must be installed. (

*)

(*)You can download Dante Controller from the download page of the following

website.

http://www.yamahaproaudio.com/

● Ethernet cable (CAT5e or better)

● Network switch (with gigabit Ethernet support)

● R series units ( up to twenty four units) with firmware V3.00 or later

Operation

Keyboard Shortcuts

<Windows modifier key> ( <Mac modifier key>) + <key> or click shows the shortcut keys. For example,

<Ctrl> (<command>) +click means “press <Ctrl> under Windows or <command> under Mac, then

click.”

Right Click

On Mac click while holding down the <control> k ey.

R Remote Version 3 User’s Guide 5

■ Setup

The setup workflow is shown below.

Install the R Remote

↓

Set on the R series units

↓

Connect the computer and R series units

↓

Power-on the R series units

↓

Specify the computer's IP address

↓

Use Dante Controller or the CL/QL series console to specify

the routing

For details on connections and settings for the R series units, refer also to the owner's manual of your

R series units.

Install the R Remote

The installation procedure is as follows.

1. Logon to Windows or Login to Mac with administer account.

2. After decompressing the downloaded file, double-click “setup.exe”(Windows) or “Install R Remote

Vxxx.pkg”(Mac)(xxx is version) in the decompressed file location.

The R Remote setup wizard will appear.

・ Under Windows, the “User Account Control” dialog box may appear. Click [Continue] or [Yes].

3. Proceed with the installation as directed by the instructions in the screen.

R Remote Version 3 User’s Guide 6

Set on the R series units

For Rio3224-D / Rio1608-D / Ri8-D

When using R Remote to operate a Rio3224-D / Rio1608-D / Ri8-D unit, set the DIP switches and

[UNIT ID] rotary switch of the unit, taking note of the following settings.

・ Set the UNIT ID in the range of 1 to 24 (hexadecimal 18). R Remote will not detect units with a

setting of 0 or 25 or higher. (For details on converting between decimal and hexadecimal, refer to

"Decimal/hexadecimal conversion table."

)

・ Set the DIP switches to the following combinations. Put DIP switches 5 and 6 in the upward

position.

・UNIT ID

Settings

Switch

UNIT ID ranging from 0 to F

(1 up)

UNIT ID ranging from 10 to 1F

(1 down)

・IP address

Specify the IP address that R Remote uses for control. This is the setting for control; it is different

than the IP address of the Dante network, so it will be different than the IP address specified on

the Dante Controller.

The first time that you connect an R series unit to your computer after purchasing it, set this to

something other than STATIC IP (MANUAL). If you want to use the STATIC IP (MANUAL)

setting, first specify the IP address from R Remote and then switch to STATIC IP (MANUAL).

Settings Switch

AUTO IP

(The Dante network automatically sets the IP address to

169.254.xx.xx)

(2 and 3 up)

DHCP

(The IP address assigned by the DHCP server will be used.)

(2 down, 3 up)

STATIC IP(AUTO)

(The IP address will be set to 192.168.0.xx (xx= UNIT ID).)

(2 up, 3 down)

STATIC IP(MANUAL)

(Set the IP address to the value specified by R Remote)

(2 and 3 down)

R Remote Version 3 User’s Guide 7

If the network consists only of Dante devices and R Remote, we recommend that you use the AUTO IP setting.

If you are connecting to an existing network, select DHCP as needed.

If you want to use zoning to set the IP address, or want to connect to an existing network but use a static IP

address, choose STATIC IP (MANUAL) and use R Remote to set the IP address.

・SECONDARY PORT

Settings Switch

DAISY CHAIN

(4 up)

REDUNDANT

(4 down)

・START UP MODE

Settings Switch

REFRESH

(The unit starts up with part of the internal memory

initialized.

Initialization creates the following settings.

・HA GAIN (-6 dB)

・+48V (OFF)

・HPF (OFF)

・HPF FREQ (80Hz)

・Gain Compensation (OFF))

(7 and 8 up)

RESUME

(The unit starts up using the settings assigned prior to the

most recent power off.)

(7 down, 8 up)

If a CL/QL series unit is not connected, we recommend that you set START UP MODE to RESUME. If this is set to

REFRESH, settings must be transmitted from R Remote each time the R series unit is restarted.

For RSio64-D

When using R Remote to operate an RSio64-D unit, set the DIP switches and [UNIT ID] rotary switch

of the unit, taking note of the following settings.

Set the DIP switches to the following setting.

・SECONDARY PORT

Settings

Switch

DAISY CHAIN

(4 up)

R Remote Version 3 User’s Guide 8

REDUNDANT

(4 down)

・START UP MODE

Settings

Switch

NORMAL

(Start up normally with the settings of the previous start-up.)

(7 and 8 up)

INITIALIZE

(The unit starts up with the internal memory initialized.

Initialization creates the following settings.

・SLOT 1-4 SRC (OFF)

・WORD CLOCK SELECT (DANTE/48kHz)

・USER PATTERN (Same routing configuration as the preset

PATTERN # 1)

・STATIC IP (Manual) (0.0.0.0)

・PANEL LOCK (Unlock)

・Dante PATCH (All OFF)

・Dante DEVICE LABEL (Y001-Yamaha -RSio64-D-123456)

(*1))

(7 down, 8 up)

(*1) The third and fourth characters of the Dante device label depend on device setting DIP switch

1 and the SETUP [UNIT ID] rotary switch. The lower six digits depend on the lower six digits of

the unit’s MAC address.

For RMio64-D

When using R Remote to operate an RMio64-D unit, set the DIP switches and [UNIT ID] rotary switch

of the unit, taking note of the following settings.

Set the DIP switches to the following setting.

・SECONDARY PORT

Settings

Switch

DAISY CHAIN

(1 up)

REDUNDANT

(1 down)

R Remote Version 3 User’s Guide 9

Connect the computer and R series units

Use an Ethernet cable to connect the computer and the R series units.

If you selected DAISY CHAIN in “SECONDARY PORT” on the above, connect the Dante connectors of

the R series units in a daisy chain to the computer.

If you selected REDUNDANT in “SECONDARY PORT” on the above, connect the computer to the

network switch that is connected to the Dante [PRIMARY] connector.

Power-on the R series units

Power-on the R series units. If you power-on before making “Settings on the R series units,”

the

settings will not be applied.

R Remote Version 3 User’s Guide 10

Specify the computer's IP address

Specify the computer's IP address so that it can communicate with the R series units.

The method of making this setting depends on whether you're using Windows or Mac. Also, the

computer's IP address setting will differ depending on the IP address specified in

"Settings on the R

series units."

If you're using Mac, click the link.

For Windows

Accessing the Control Panel

The way to access the Control Panel will depend on your operating system.

 Windows 7

Select [Start] → [Control Panel].

 Windows 8 / Windows 8.1

1. In the Start screen, click [Desktop].

The desktop will appear.

2. Move the cursor to the upper right or lower right corner of the desktop.

The Charms bar will appear.

3. Select [Settings] → [Control Panel].

TCP/IP Settings

Make TCP/IP settings for the computer as follows.

1. Access the Control Panel, then click or double-click [Network and Sharing Center] or [View

network status and tasks].

The “Network and Sharing Center” is displayed.

2. Click [Manage network connection] or [Change adapter settings] from the “Tasks” list located in

the left side of “Network and Shearing Center” window, then double-click [Local Area

Connection].

The “Local Area Connection Status” dialog box will be displayed.

・The “User Account Control” dialog box may appear. Click [Continue] or [Yes].

・If the “Local Area Connection properties” dialog box appears, skip ahead to step 4.

3. Click [Properties].

The “Local Area Connection properties” dialog box will be displayed.

The “User Account Control” dialog box may appear. Click [Continue] or [Yes].

4. Select [Internet Protocol Version 4(TCP/IPv4)], then click [Properties].

The “Internet Protocol Version 4(TCP/IPv4) Protocol” dialog box will be displayed.

R Remote Version 3 User’s Guide 11

5. Make the following settings according to the IP address setting you made in "Settings on the R

series units."

AUTO IP or DHCP STATIC IP (AUTO)

Click [Obtain an IP address automatically].

Click [Use the following IP address:]. As the IP

address, enter "192.168.0.xxx (a value in the

range 1 to 254 that does not conflict with any

other device, including the R series units), and

enter "255.255.255.0" as the subnet mask.

The 192.168.0.101 shown below is an example.

If you're using STATIC IP (MANUAL), specify the setting that's appropriate for your network. For

details, consult your network administrator.

6. Click [OK].

Proceed to "Use Dante Controller or the CL/QL series console to specify the routing."

R Remote Version 3 User’s Guide 12

For Mac

Make TCP/IP settings for the computer as follows.

1. Click [System Preferences]→[Network].

The “Network” dialog box will be displayed.

2. Click the service that you want to connect to the R series unit.

If you're using the Ethernet port that's built into the Mac, click [Ethernet].

3. Make the following settings according to the IP address setting you made in "Settings on the R

series units."

AUTO IP or DHCP STATIC IP (AUTO)

In "Configure IPv4," choose [Using DHCP].

In “Configure IPv4,” choose [Manually]. As the IP

address, enter "192.168.0.xxx (a value in the

range 1 to 254 that does not conflict with any

other device, including the R series units), and

enter "255.255.255.0" as the subnet mask.

The 192.168.0.101 shown below is an example.

If you're using STATIC IP (MANUAL), specify the setting that's appropriate for your network. For

details, consult your network administrator.

4. Click [Apply] button, then close “Network” dialog box.

Use Dante Controller or the CL/QL series console to specify the routing

You'll use Dante Controller or the CL/QL series console to specify the routing.

If you're using Dante Controller to specify the routing, refer to "Dante Controller User’s Guide."

If you're using a CL/QL series console to specify the routing, refer to the each Reference Manual.

This completes the setup.

R Remote Version 3 User’s Guide 13

■ Operating R Remote

Start R Remote.

Windows 7 users: click [Start]→[All Programs]→[Yamaha R Remote]→[R Remote]

Windows 8/8.1 users: in the "Start screen," double-click the [R Remote] tile.

Mac users: click [Go]→[Applications]→ double-click [R Remote].

・ When you start R Remote, the "Network Setup" dialog box may appear, allowing you to select the computer's

network card that will be used for communication with the R series units. If this appears, click the network card

that is connected to the R series unit, and then click the [Apply] button.

・ For R Remote for Windows 8 / Windows 8.1, depending upon user access privileges, the software's "Tile(icon)" may

not appear on the "Start screen". In such cases, you can find the software icon in "Apps" by the following steps:

1. Right-click anywhere on Start screen.

2.

Click "All apps" button at the bottom right side of Start screen.

Menu bar

The commands that can be executed by R Remote can be found here, grouped by category.

Click here to see a list of commands.

Menu

Command

Summary

Dialog box that appears

[File] [Open] Opens a previously-saved file (rrmt

format or rrm format).

If you open the file when R series units are

connected, the settings will be applied to the

R series units. Be aware that if a CL/QL

series console is also connected, its settings

will be overwritten.

“Open File” dialog box

[Save As]

Saves the file. It will have a file name

extension of rrmt, and will be usable

only by R Remote.

“Save File” dialog box

[Network Setup] Selects the computer’s network

adapter that will be used to

communicate with the R series.

"Network Setup" dialog

box

[Device Information]

Displays information about the R

series units that are connected.

"Device Information"

dialog box

[Quit] Quits R Remote. ---

[About] *1

[About R Remote]

Displays details such as the software

version of R Remote.

“About R Remote”

dialog box

*1 Mac users: [About] is located in the R Remote menu.

R Remote Version 3 User’s Guide 14

Areas of the screen

The R Remote screen is broadly divided into three areas: the Device Selection Area, the Information

Display Area, and the Main Area.

R Remote Version 3 User’s Guide 15

Device Selection Area

When you click a display switching button, the corresponding R series unit is shown

in the information display area and in the main area.

With a display switching button selected, pressing the left button makes all

indicators of the corresponding R series unit blink, allowing you to identify the

corresponding unit.

When you right-click a display switching button, the following context menu

appears.

Command

Summary

[Mount]

Opens the "Mount" window. Select the device that you want to mount.

[Connect]

Synchronizes with the selected device.

[Disconnect]

Disconnects from the selected device.

[Properties] Open the “Properties” dialog box.

The connection status is shown below each display switching button.

Indication

Status

VIRTUAL

The device is mounted without the existence of the actual device.

CONNECTING

Currently synchronizing with the device.

CONNECTED

Currently synchronized with the device.

DISCONNECTED

Synchronization with the device is possible, but is currently disconnected by the

[Disconnect] command. Alternatively, communication has been interrupted, or

connection failed.

DUPLICATED

More than one device of the same UNIT ID exists. Eliminate any UNIT ID

conflict between devices.

The VIRTUAL indication is also shown if the device is in any of the following states.

・Device is not powered-on.

・Not connected to the computer.

・Communication is impossible due to incorrect settings.

Information Display Area

This area shows the UNIT ID and name of the selected device.

To check the firmware version or IP address, choose [File] menu -> [Device Information] to open the

"Device Information" dialog box.

R Remote Version 3 User’s Guide 16

Main Area

This area shows the state of the selected R series unit and allows basic parameter editing. The display

depends on the model.

For Rio3224-D / Rio1608-D / Ri8-D

The screen is explained here using the Rio3224-D as an example. The number of items in the HA

display area differs depending on the model.

The Edit window

opens if you double-click or right-click and choose [Open Edit Window] anywhere

other than on a controller.

① HA display area

Here you can view and edit HA settings for the Rio3224-D / Rio1608-D / Ri8-D unit.

If you press the left mouse button on an area that shows the device's jack number, the indicator of

the actual device's corresponding jack will light.

ⓐ [+48V] button

Turns phantom power on/off for each channel.

ⓑ GAIN knob

Specifies the analog gain for the HA of the device. The current setting is shown in the

numeric box located below the knob.

R Remote Version 3 User’s Guide 17

You can double-click a numeric value box and enter a value directly from the keyboard.

The level meter located at the immediate right of the knob indicates the input level of the

corresponding port.

On the knobs, you can use the following shortcuts and context menu.

Action

Operation

<Ctrl> (<command>) + click

Sets analog gain to the default value (-6 dB).

<Ctrl> (<command>) + <Shift> +

click

Sets the analog gain to 0 dB.

Right click

Displays the following context menu.

[All Default]

Sets the analog gain of all

channels to the default value (-6

dB).

[All 0dB]

Sets the analog gain of all

channels to 0 dB.

This is an on/off switch for the high-pass filter that is built into the HA of the device. To

specify the cutoff frequency, make settings in the Edit window

.

② [+48V MASTER] indicator

Indicates the master phantom power on/off status for the device (the on/off setting is switched on

the device itself).

③ [SYSTEM] indicator / [SYNC] indicator

Indicates the status of the device or the Dante status. When you move the mouse cursor to this

area, the display content appears as a popup.

④ [PEAK HOLD] button

If this button is on, the peaks of each level meter are held. When you turn this off, the peaks that

had been held are cancelled.

R Remote Version 3 User’s Guide 18

Edit window

This appears if you double-click in the main area other than on a controller, or if you right-click and

choose [Open Edit Window].

Here you can view and edit detailed HA settings for the device. To close the window, click the [x]

button in the upper right if you're using Windows, or click the [x] button if you're using Mac.

The screen is explained here using the Rio3224-D as an example. The number of channel switching

tabs differs depending on the model.

① Device name

Shows the UNIT ID number and name of the device.

② [PEAK HOLD] button

If this button is on, the peaks of each level meter are held. When you turn this off, the peaks that

had been held are cancelled.

③ Port select tab

For the Rio3224-D or Rio1608-D, these tabs switch the ports that are shown.

④ Port index

Indicates the port number of the device. When you press this with the left mouse button, the

indicator of the corresponding port of the device will light.

⑤ [+48V] button

Turns the HA phantom power on/off.

R Remote Version 3 User’s Guide 19

⑥ [A.GAIN] knob

Specifies the analog gain for the HA of the device. The current setting is shown in the numeric box

located below the knob.

You can double-click a numeric value box and enter a value directly from the keyboard.

The level meter located at the immediate right of the knob indicates the input level of the

corresponding port.

On the knobs, you can use the following shortcuts and context menu.

Action

Operation

<Ctrl> (<command>) + click

Sets analog gain to the default value (-6 dB).

<Ctrl> (<command>) + <Shift> +

click

Sets analog gain to 0 dB.

Right click

Displays the following context menu.

[All Default]

Sets the analog gain of all

channels to the default value (-6

dB).

[All 0dB]

Sets the analog gain of all

channels to 0 dB.

⑦ [GC] button

Switches on/off the gain compensation that regularizes the signal level on the audio network. If

this is on, the gain value fixed by gain compensation is displayed, and subsequent changes to

analog gain is compensated by the compensation gain within the device; audio is transmitted to

the Dante network at the gain value that was fixed immediately before this was enabled.

There are limits to the amount of gain compensation. The maximum compensation is 24 dB when turning the knob

toward the left, and 48 dB when turning the knob toward the right. For example if you apply gain compensation at

30 dB, compensation is maintained until you set the analog gain to 6 dB, but if you set the analog gain to 4 dB, the

gain value that is output will be 28 dB. If in this state you return the setting to 6 dB or higher, compensation

maintains the level at 30 dB.

⑧ [FREQ] knob / [HPF] button

Switches on/off the high-pass filter that is built into the HA of the device, and adjusts the cutoff

frequency. The current setting is shown in the numeric box located below the knob.

If you <ctrl> (<command>) + click above the [FREQ] knob, the cutoff frequency is set to the default

value (80 Hz).

R Remote Version 3 User’s Guide 20

For Ro8-D

The Ro8-D has no settings that can be operated, so only the [SYSTEM] indicator and [SYNC] indicator

are shown.

① [SYSTEM] indicator / [SYNC] indicator

Indicates the status of the device or the Dante status. When you move the mouse cursor to this

area, the display content appears as a popup.

Страница загружается...

Yamaha V3 Руководство пользователя

Похожие модели бренда

Модели других брендов