KMA-1080/KMA-980
Digital Karaoke Mixing Amplifier
L
OWNER’S MANUAL
MANUAL DE INSTRUCCIONES
i En
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
10 cm (3-15/16”) on the top, left and right of this unit, and
20 cm (7-7/8”) on the back.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot (or vice versa), and do not locate this unit in an
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit, which
may cause an electrical shock, fire, damage to this unit, and/or
personal injury.
5 Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to an AC wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the AC wall outlet,
grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
Yamaha will not be held responsible for any damage resulting
from use of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cord
disconnected from an AC wall outlet or the unit during a
lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the AC
wall outlet.
16 Install this unit near the wall outlet and where the AC power
plug can be reached easily.
17 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
18 Before moving this unit, press / switch to turn this unit off,
and disconnect the power cord from the AC wall outlet.
19 The batteries shall not be exposed to excessive heat such as
sunshine, fire or like. When you dispose of batteries, follow
your regional regulations.
20 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the
outlet, then leave the unit alone.
21 When using the unit for a long time, the unit may become
warm. Turn the power off, then leave the unit alone for
cooling.
Caution: Read this before operating your unit
The following rack size measurements must be adhered to:
12 The ventilation space on the top, left and right of this
unit; more than 10 cm (3-15/16”)
3 The ventilation space on the back of this unit; more
than 20 cm (7-7/8”)
4 Do not remove the feet.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
As long as this unit is connected to the AC wall outlet,
it is not disconnected from the AC power source even
if you turn off this unit by / switch.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
foot foot
rack
1 En
PREPARATIONINTRODUCTION
OPERATION
ADDITIONAL
INFORMATION
English
HANDLING PRECAUTIONS .............................. 2
BEFORE CONNECTING ..................................... 2
NAMES OF PARTS AND THEIR FUNCTIONS
.............................................................................. 3
SYSTEM CONNECTIONS ................................... 6
CONNECTIONS .................................................... 7
CONFIGURATION DIAGRAM ........................ 10
REMOTE CONTROL ......................................... 11
GENERAL OPERATION ................................... 13
SETUP MODE...................................................... 14
TROUBLESHOOTING....................................... 17
MAINTENANCE ................................................. 18
AFTER-SALES SERVICING............................. 18
KARAOKE ETIQUETTE................................... 18
COPYRIGHT ....................................................... 18
SPECIFICATIONS .............................................. 19
CONTENTS
INTRODUCTION
PREPARATION
OPERATION
ADDITIONAL INFORMATION
2 En
INTRODUCTION
Thank you for your purchase of the Yamaha KMA-1080/KMA-980 Digital Karaoke Mixing Amplifier.
This document is the owner’s manual for both KMA-1080 and KMA-980. Model names are given where the details of
functions are unique to each model. Illustrations for KMA-1080 are mainly used for explanations.
Before using this unit, be sure to read this manual so that you can take full advantage of the features of this unit.
After you finish reading, keep this manual in a safe place in case you need it in the future. The manual should be very
helpful in understanding the Digital Karaoke Mixing Amplifier and solving any difficulties that may arise during use.
■ Do not install the unit in the following
locations:
• In places exposed to direct sunlight or near heat
sources, such as a radiator.
• In places where heat cannot escape due to poor
ventilation, or are very humid or dusty.
• On a sloping surface or exposed to excessive vibration.
• In places which may be exposed to rain, such as near a
window.
• In places which may be exposed to soot, vapor or heat,
such as near cooking facilities.
■ Connection precautions
• Be sure to switch off the power of the relevant
equipment before making any connection.
• The white input/output jacks of the amplifier are
designed for the left channel, while the red input/output
jacks are for the right channels. Be sure to connect the
cords without making a mistake in the color codes for
the left and right channels.
• Insert the plugs of the connection cords securely into
the jacks. If the connection is incomplete, there may be
no sound produced or noise may be generated.
• When unplugging the power cable from the AC wall
outlet, be sure to hold the plastic molding of the plug
itself and pull.
• For KMA-1080, set IMPEDANCE SELECTOR on the
rear panel before turning on the unit. Refer to
“IMPEDANCE SELECTOR” on page 7.
HANDLING PRECAUTIONS
BEFORE CONNECTING
3 En
PREPARATION
English
PREPARATION
1 / (power on/off)
Turn the power on/off.
2 MUSIC BALANCE
Adjust the volume balance.*
3 MUSIC TONE (BASS/TREBLE)
Adjust the low/high frequency response.*
4 MIC ECHO DELAY
Adjust the delay time between echoes.*
5 MIC ECHO REPEAT
Adjust the amount of feedback.*
6 ECHO MODE
Select NORMAL, WIDE (stereo) or SPACIOUS** echo.
SPACIOUS echo is an effect that produces both
NORMAL and WIDE echo with a time lag. The LED
lights up in amber/green** when WIDE/SPACIOUS**
echo is selected.
ECHO MODE is reset after the played song has finished
when the ECHO MODE auto reset is set to on. Refer to
“ECHO MODE auto reset” on page 14. The unit assumes
songs have finished when over 4 seconds of silence occurs.
7 MIC TONE (BASS/MID/TREBLE)
Adjust the low/middle/high frequency response of
microphones.*
8 MIC jacks (1/2/3**)
Connect microphones to these jacks.
9 MIC VOL (1/2/3**)
Adjust the microphone input level.*
0 MIC
Adjust the overall volume of all microphones.
A Remote sensor
This sensor receives signals from the remote control.
B ECHO
Adjust the amount of echo.
C INPUT/Input source indicators (DVD/AUX**/
TAPE/BGM)
INPUT is not available in the default setting.
To activate INPUT, refer to “Input mode” on page 14.
Input source indicators indicate the input source currently
active.
D MUSIC
Adjust the volume of the music source.
E KEY CONTROL
To transpose the key of the played music, rotate this
control. The key can be changed in halftone steps in 5
steps; either higher or lower. To reset the key to the
natural key, press this control. If over 4 seconds of silence
occurs, the unit assumes the played song has finished and
resets the key to natural.
NAMES OF PARTS AND THEIR FUNCTIONS
Front panel
The shaded part ( ) is provided for KMA-1080 only.
* Use a flathead screwdriver to adjust.
** KMA-1080 only
4 En
NAMES OF PARTS AND THEIR FUNCTIONS
For details on component connection, refer to “SYSTEM
CONNECTIONS” on page 6.
1 BALANCED MIC INPUT jacks (1/2)
Connect microphones to these jacks.
These are balanced inputs and each connects to the same
circuit MIC 1 and 2 on the front panel.
2 DVD audio input jacks
Connect to the output jacks of KARAOKE equipment or
DVD player.
3 AUX audio input jacks*
Connect to the output jacks of a TAPE player, VCR, etc.
4 TAPE audio input jacks
Connect to the output jacks of a TAPE player, VCR, etc.
5 TAPE audio output jacks
Connect to the input jacks of a TAPE player, VCR, etc.
6 BGM audio input jacks
Connect to the output jacks of the source component of
background music.
7 SUBWOOFER jack without low-pass filter
Connect to the input jack of the subwoofer with a low-
pass filter. This jack outputs the monaural signal directly.
8 SUBWOOFER jack with low-pass filter
Connect to the input jack of the subwoofer.
9 PRE OUT jacks
Connect to the input jacks of the extension power
amplifier.
0 IMPEDANCE SELECTOR*
Refer to “IMPEDANCE SELECTOR” on page 7.
A REMOTE jack
Connect to an external remote control.
Refer to “Connecting an external remote control” on page
8.
B VIDEO INPUT jacks
Connect to the input jack of the video output of a DVD,
AUX*, or background video player or video camera, etc.
Rear panel
The shaded part ( ) is provided for KMA-1080 only.
* KMA-1080 only
5 En
NAMES OF PARTS AND THEIR FUNCTIONS
PREPARATION
English
C DVD INPUT LEVEL
Adjust the balance of the DVD input level with respect to
other inputs (AUX*, TAPE, BGM).
D AUX INPUT LEVEL*
Adjust the balance of the AUX input level with respect to
other inputs (DVD, TAPE, BGM).
E TAPE INPUT LEVEL
Adjust the balance of the TAPE input level with respect to
other inputs (DVD, AUX*, BGM).
F BGM INPUT LEVEL
Adjust the balance of the BGM input level with respect to
other inputs (DVD, AUX*, TAPE).
G SPEAKERS (Speaker system terminal(s))
Connect to the speaker system(s).
For KMA-980, only one speaker system is available.
H Power cable
Plug this cable into an AC wall outlet after all other
connections are complete.
I Signal ground terminal
Connect this terminal if a humming noise is emitted when
connecting this amplifier.
J VIDEO OUTPUT jacks
Connect to the video input of the monitor.
K HOWLING CANCELLER
Set this switch to reduce the room's acoustic feedback. To
reduce the feedback, select 1. If reduction in feedback is
not sufficient, select 2. Select OFF to cancel feedback
reduction.
The shaded part ( ) is provided for KMA-1080 only.
* KMA-1080 only
6 En
OPERATION
SYSTEM CONNECTIONS
MIC
Monitor TV
MIC
Monitor TV
Monitor TV
System 2
Active subwoofer
System 1
Active subwoofer
(With lowpass filter)
System A
Right Left
System B
(KMA-1080 only)
Right Left
KARAOKE/
DVD player
VTR/LD
player
(KMA-1080
only)
Background
music/video
player
Power
amplifier
The shaded part ( ) is provided for KMA-1080 only.
TAPE
recorder
7 En
OPERATION
English
■ Connecting speaker cords
1 Pull the lever up to open, then insert the
conductor wire into the hole.
2 Close the lever to secure the conductor wire.
Before connection, strip a section of coating 15 mm
(9/16”) in length from the end of each cord using a
tool such as pliers.
Be careful that the cord conductors projected from a terminal do
not contact with another cord. Contact from the conductors of
different speaker cords may cause damage to the system.
■ Important precautions for speaker
connection
• The maximum outputs of this unit are as follows:
KMA-1080................................................200 W + 200 W
KMA-980..................................................150 W + 150 W
Accordingly, the maximum input power of the speakers
used must exceed the above.
• Use Yamaha speakers to prevent any trouble or
damage caused by mismatching.
[For KMA-1080]
IMPEDANCE SELECTOR
• Before turning on this unit, be sure to set
IMPEDANCE SELECTOR on the rear panel to the
position whose requirements your speaker system
meets.
• Do not change IMPEDANCE SELECTOR setting
while the power to this unit is on, otherwise this unit
may be damaged.
Connection examples
The minimum speaker impedance is 4 Ω. If two 6 Ω
speaker systems are connected in parallel, this will exceed
the design value and trigger a safety protector device.
When two speaker systems are used and the protector is
frequently activated, the speaker systems should be
connected serially instead.
CONNECTIONS
Note
(+) cord to
(+) terminal
(–) cord to (–) terminal
The shaded part ( ) is provided for KMA-1080 only.
15 mm (9/16”)
Right
speaker
Left
speaker
The shaded part ( ) is provided for KMA-1080 only.
Switch
position
If your system
uses:
Speaker
impedance level
Low
One speaker system
4 Ω or higher
Two speaker systems
8 Ω or higher
High
One speaker system
8 Ω or higher
Two speaker systems
16 Ω or higher
(Low) (High)
8 En
CONNECTIONS
1. Parallel connection
(each speaker should be 8 Ω or more)
2. Series connection
(total: over 4 Ω is available)
[For KMA-980]
The speaker impedance must be between 8 Ω to 16 Ω.
■ Connecting the RCA pin plugs
When connecting RCA pin plugs, be sure to insert the red
plug into the red jack and the white plug into the white
jack.
■ Connecting to the balanced input
■ Connecting to the unbalanced input
■ Connecting an external remote control
6 Ω 6 Ω
6 Ω + 6 Ω ➝ 3 Ω
(<4 Ω : NG)
6 Ω 6 Ω
6 Ω + 6 Ω = 12 Ω
(>4 Ω : OK)
Left
Right
White
Red
White
Red
HOT
COLD
GND
HOT
COLD
GND
HOT
GND
HOT
GND
or
GND
+5V_OUT
REMOTE
(Direct)
REMOTE
+5V
OUT
GND
+5V_OUT
REMOTE
GND
External remote control
satellite
RMC KMA-1080/
KMA-980
REMOTE (Direct)
GND
RMC KMA-1080/
KMA-980
9 En
CONNECTIONS
OPERATION
English
1. External remote control satellite
Connect to +5V_OUT, REMOTE and GND.
By connecting the remote control satellite to this input, this unit
can receive the signal of the remote control.
2. REMOTE (Direct)
Connect to REMOTE (Direct) and GND.
Connect to the infrared diode output (open collector) of
RMC.
By connecting the REMOTE (Direct) to this input, this unit can
receive the signal of the REMOTE.
Note
Note
10 En
* KMA-1080 only
** Balanced input, on the rear panel
CONFIGURATION DIAGRAM
11 En
OPERATION
English
■ Names of parts and their functions
1 INPUT
INPUT is not available in default setting.
To activate INPUT, refer to “Input mode” on page 14.
2 KEY CONTROL ( / / )
Transpose the key of the played music.
3 MIC ( / )*
Adjust the overall volume of the microphones.
4 ECHO ( / )*
Adjust the amount of echo.
5 MUSIC ( / )*
Adjust the music volume.
* The LED on the corresponding control on the front panel blinks
during adjustment.
6 PRESET (1/2/3)
Recall saved preset settings for MIC volume/ECHO
amount/MUSIC volume/ECHO MODE.
To save current settings of the above, press the desired
button (PRESET 1, 2, 3 or KEY CONTROL on the front
panel) for 3 seconds. Pressing KEY CONTROL saves
settings to PRESET 1. When save is completed, “ ” on
the KEY CONTROL blinks once. You can save up to 3
presets (PRESET 1/2/3) on this unit. Refer to “Power ON
recall” on page 14.
7 ECHO MODE
Select NORMAL, WIDE or SPACIOUS (KMA-1080
only) echo.
■ Preparing the remote control
The remote control comes with the battery already
installed. Before using the remote control for the very first
time, pull out the plastic tab, as shown.
For information on replacing the battery, refer to next
section.
■ Operation of remote control
1. Remote control
The distance between the remote control and the remote
sensor of this unit should be within 6 m (20’). Be sure to
aim the remote control directly at the remote sensor on the
front panel.
Continued to the next page.
REMOTE CONTROL
Plastic tab
Within 6 m
(20’)
30°
30°
12 En
REMOTE CONTROL
2. Loading a battery
The life of the battery used in the remote control is about
half a year under normal use. Remove the battery if the
remote control is not used for an extended period. When
the battery becomes weak, replace with a new CR2025
battery.
To replace the battery:
1. Using a small screwdriver, carefully slide out the
battery holder.
2. Remove the expired battery, and place the new
CR2025 battery onto the battery holder with the + side
facing up.
3. Slide the battery holder into the remote control, and
push it so that it clicks shut.
Improper use of batteries may cause a risk of battery
leakage and explosion.
Adhere to the following guidelines:
• Do not attempt to recharge the old battery.
• Insert a battery so that the positive (+) and negative (–)
poles are positioned as shown.
• Even if the shapes are the same, the voltage of batteries
may vary depending on the models. Be careful not to
use different model of battery.
• Dispose of the old battery in accordance with local
regulations.
+ side up
13 En
OPERATION
English
1 Connect the required number of
microphones.
2 Set the power switches of this unit and other
required components to on.
3 Play the KARAOKE music source
component, and adjust the volume by
rotating MUSIC.
The music source is selected automatically in default
setting. To set the conditions for selection, refer to
“Auto input condition” on page 14. To select the
music source manually, refer to “Input mode” on
page 14.
4 Adjust the microphone volume by rotating
MIC.
When different microphone volumes are not
balanced, adjust MIC VOL using a flathead
screwdriver.
5 Adjust the ECHO amount by rotating ECHO.
6 Adjust the key by rotating KEY CONTROL.
■ Notes for the proper use of microphones
• Sing into the microphone by holding it at a distance of 5 to
10 cm (2 to 3-15/16”) from your mouth.
• To ensure clear sound, grasp the microphone below the mic
head.
• Do not block the lower part of the windscreen. This will disturb
proper voice reproduction with unclear bass. Howling also
tends to occur in such cases.
GENERAL OPERATION
The shaded part ( ) is provided for KMA-1080 only.
5 to 10 cm (2 to 3-15/16”)
away from your mouth.
Grasp the microphone below
the head.
14 En
■ Menus in Setup mode
You can set the following menus in Setup mode:
1. Power ON recall
Select Last memory or Preset, to recall the settings of MIC
volume/ECHO amount/MUSIC volume/ECHO MODE
when the unit is turned on.
Last memory*: The settings when the unit was turned off
last are recalled.
Preset: The settings saved to PRESET 1 are recalled.
2. Input mode
Set Input mode to Auto or Manual.
Auto*: The input source is set automatically.
Manual: The input source is selected by INPUT.
Source is selected in order of DVD, AUX**, TAPE, BGM.
3. Auto input condition
Set the conditions for each source (DVD, AUX** and
TAPE) for Auto Input mode described in 2.
Audio*: The source is switched based on audio signal.
Video: The source is switched based on video signal.
Audio/Video: The source is switched based on audio or
video signal.
For only this menu, select desired source by INPUT
before selecting the desired item.
4. ECHO MODE auto reset
Select whether the selected ECHO MODE is reset or not
after the current song has finished. The unit assumes songs
have finished when over 4 seconds of silence occurs.
Off*: The unit retains the last selected ECHO MODE.
On: The ECHO MODE is reset to the mode that is
recalled when this unit is turned on. Refer to “Power ON
recall” on this page.
5. Remote mode
Set the light receiving device.
Front&Ext.*: Both the front panel and external remote
control satellite receive the signal from the remote control.
Front: Only the front panel receives the signal.
Ext.: Only the external remote control satellite receives
the signal.
Disable: The remote control is disabled.
6. MIC/MUSIC max level
Set the maximum volume of MIC and MUSIC.
10*: No setting.
9 to 3: The maximum volume is set to the level indicated
(2 to 0 cannot be set).
7. MIC/MUSIC volume select
Select how MIC and MUSIC volumes increase/decrease
(i.e., the volume curve) when the controls are turned.
Pattern 1: Steep curve
Pattern 2*: Less steep curve
Pattern 3: Least steep curve, and is most suitable for fine
adjustment.
8. Ext Output select
Set the output signals from PRE OUT/SPEAKERS.
Normal*: PRE OUT/SPEAKERS output both of the mic/
music signals.
Separate: PRE OUT outputs music; SPEAKERS outputs
mic signals.
9. Power Amplifier mode
You can also use this unit as a 2ch power amplifier. Most
of the functions on this unit are not available in Power
Amplifier mode. The default setting is Normal (Digital
Karaoke Mixing Amplifier). See the CAUTION on
page 17.
10. Initializing
Reset all the settings set in Setup mode to the defaults.
Cancel: Initializing is not executed.
Initialize: Initializing is executed.
When pressing KEY CONTROL with MUSIC set to 3,
Initializing is executed.
To set each menu above, set the corresponding controls as
shown in the “Setup mode table” on pages 15 to 16
according to the following procedure.
1 To enter Setup mode, turn off the main unit
and press / while pressing KEY CONTROL
and ECHO MODE.
2 Set KEY CONTROL and MUSIC according to
the “Setup mode table” on page 15 to set
desired menus and items.
For Auto input condition, select the desired source
before selecting the item.
Set all settings you want to change before moving to step 3.
3 Press KEY CONTROL to enter the settings.
“ ” blinks once when the settings are entered.
4 To terminate Setup mode, turn off the main
unit.
SETUP MODE
* Default setting
** KMA-1080 only
15 En
SETUP MODE
OPERATION
English
■ Setup mode table
Menu KEY CONTROL Items/MUSIC
1. Power ON recall
2. Input mode
3. Auto input condition
4. ECHO MODE auto
reset
5. Remote mode
6. MIC/MUSIC max
level
7. MIC/MUSIC volume
select
8. Ext Output select
+1 Last memory: 1 Preset: 2
+2 Auto: 1 Manual: 2
+3
Audio: 1 Video: 2 Audio/Video: 3
Select desired source
by INPUT.
Example: DVD
+4 Off: 1 On: 2
+5 Front&Ext.: 1 Front: 2 Ext.: 3 Disable: 4
–1
No setting: 10 Set to the indicated level: 9 to 3
Example: 3
Set MIC and MUSIC separately.
–2
Pattern 1: 1 Pattern 2: 2 Pattern 3: 3
–3
Normal: 1 Separate: 2
17 En
ADDITIONAL
INFORMATION
English
ADDITIONAL INFORMATION
If problems should occur, check the following table for simple remedies.
If the problem still cannot be solved, please consult your dealer.
TROUBLESHOOTING
Problems Possible causes Solutions
No speaker sound is
output at all.
/ is set to off. Set / to on.
The power cable is unplugged. Plug the power cable securely into the AC wall outlet.
MUSIC is in the lowest position. Adjust MUSIC.
The wrong music source is selected when
Input mode is set to Manual in Setup mode.
Select the correct music source with INPUT or set Input
mode to Auto in Setup mode. Refer to “Input mode” on
page 14.
The sound is cut off due to a temperature rise
in the unit.
Turn the power off, then leave the unit alone for cooling.
No sound is output from
one of the speakers.
MUSIC BALANCE is turned fully to one
speaker.
Set the control to the center position.
One of the speaker cords is disconnected. Insert the cord securely into the terminals.
No microphone sound is
output.
The microphone plug is not fully inserted. Insert the plug securely into the jack.
The switch on the microphone is set to OFF. Set the switch on the microphone to ON.
The corresponding MIC VOL or MIC controls
are in the minimum position.
Adjust the control.
The microphone is too far from your mouth, or
the microphone handling is incorrect.
Refer to the user’s manual supplied with your microphone.
The remote control does
not work, or does not
function properly.
The remote control is too far away or tilted too
much.
The remote control will function within 6 m (20’) and no
more than 30 degrees off-center from the front panel.
Direct sunlight or lighting is striking the
remote control sensor of this unit.
Reposition this unit.
Remote mode is set to Disable in Setup mode. Set Remote mode to Front&Ext., Front, or Ext. in Setup
mode. Refer to “Remote mode” on page 14.
The wrong Remote mode is set in Setup mode. Set the correct Remote mode in Setup mode. Refer to
“Remote mode” on page 14.
The battery is weak. Replace with a new CR2025 battery. Refer to “Loading a
battery” on page 12.
When INPUT does not work, Input mode is set
to Auto.
Set Input mode to Manual in Setup mode. Refer to “Input
mode” on page 14.
Power Amplifier mode is set. Set Power Amplifier mode to Normal. Refer to “Power
Amplifier mode” on page 14.
The Input source
indicators flash.
The temperature of the unit is too high or too
low.
Turn the power off and leave the unit alone for a while.
• Always use the default setting for Power Amplifier mode in normal use.
• If “Power Amplifier: 2” is set, the volume level of this unit will be maximum and cannot be controlled by rotating
MUSIC on the front panel.
• Be careful of inadvertent setting to avoid excessive volume output.
• Consult your dealer when using this unit in Power Amplifier mode.
CAUTION
18 En
When the set gets dirty, wipe it with a soft, dry cloth.
Never use alcohol, thinner, benzene, insecticide or other volatile agents, for they may damage the surface paint or gloss
of the set.
Also do not wipe the set with a chemical cloth or leave it on the set for a long period, for the surface finish may
deteriorate or the paint may be stripped off.
• If this unit is found to be defective, your local dealer
will repair or replace defective parts at charge on
request.
• Before requesting a repair from your local dealer, see
the “TROUBLESHOOTING” for possible remedies.
For the dealer:
If the customer requests after-sales service, please first
check the following points:
• Confirm the details of any accident.
• Check out all cables and connections.
• Confirm cautions regarding operation and instructions
on using the system with your customer.
If the unit is found to be defective and it is difficult to
repair, bring the defective unit to your nearest Yamaha
authorized service center.
• Broadcasting and music sources such as recorded music tapes, DVDs, video tapes, CDs and so on are strictly
protected under copyright law.
• You require permission from the copyright holder to use, distribute, or rent these music sources for commercial use,
or sell dubbed media to other people; except when enjoying these sources by yourself.
MAINTENANCE
AFTER-SALES SERVICING
KARAOKE ETIQUETTE
The KARAOKE performance you enjoy may be disturbing to others. When performing
KARAOKE, be sure to consider your neighbors.
You can control the volume of KARAOKE. Remember that even small sounds travel easily
during quiet nights, so be especially careful during KARAOKE performances at night. We
recommend consideration for your neighbors by closing your windows.
COPYRIGHT
Страница загружается ...
Страница загружается ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Yamaha KMA-980 Инструкция по применению
- Тип
- Инструкция по применению
- Это руководство также подходит для
Задайте вопрос, и я найду ответ в документе
Поиск информации в документе стал проще с помощью ИИ
на других языках
- English: Yamaha KMA-980 Owner's manual
- español: Yamaha KMA-980 El manual del propietario
Похожие модели бренда
-
Yamaha GX-3 Руководство пользователя
-
-
-
-
-
-
-
-