Yamaha A12M Инструкция по применению

ENGLISH

A10/A12/A15/A12M

A15W

Owner’s Manual

SPEAKER SYSTEM

SUBWOOFER

Thank you for choosing this YAMAHA speaker system. In order to take maximum advantage of the speaker’s fea-

tures and ensure maximum performance and longevity, please read this manual carefully before using the speaker

system. Keep the manual in a safe place for future reference.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Do not open the device or attempt to disassemble the internal parts or

modify them in any way. The device contains no user-serviceable parts.

If it should appear to be malfunctioning, discontinue use immediately

and have it inspected by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might

spill into any openings.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the device or other property. These precautions include, but are not limited to, the following:

• If you use a stand, make sure to observe the following precautions in

order to avoid toppling the device or causing damage to the internal

components.

- Check the stand’s speciﬁcations and make sure that it is sturdy enough to

support the weight of the speaker.

- Mount only one speaker on each speaker stand.

- Use the supplied screws if included.

-Tighten fastening screws securely.

- Use the speaker stands with their legs fully opened.

- Use the stand at a height of less than 140cm (55").

- Add weight such as sand bags around the stand legs to prevent them from

falling over.

- Remove the speakers from the stands before moving the stands or adjusting

their height.

- Limit the number of people around the placed stand.

We recommend using the TS-80 and TS-90 speaker stands

manufactured by Ultimate Support Systems, Inc. (sold separately) to

support the speakers.

• If you use the metal socket on the subwoofer for mounting of a satellite

speaker, use a pole no longer than 90cm (35.4") with an outer diameter

of 35mm (1-3/8"). Use of any other size pole may cause the device to

fall, and result in injury or damage to the internal components.

• When transporting or moving the device, always use two or more

people. Attempting to lift the device by yourself may damage your back,

result in other injury, or cause damage to the device itself.

• Before moving the device, remove all connected cables.

• Do not use the speaker’s handles for suspended installation. Doing so

can result in damage or injury.

• Do not expose the device to excessive dust or vibrations, or extreme

cold or heat (such as in direct sunlight, near a heater, or in a car during

the day) to prevent the possibility of panel disﬁguration or damage to

the internal components.

• Do not place the device in an unstable position where it might

accidentally fall over.

Do not open

Water warning

Location

(6)-1

ENGLISH

• Before connecting the device to other devices, turn off the power for all

devices. Before turning the power on or off for all devices, set all

volume levels to minimum.

• Use only speaker cables for connecting speakers to the speaker jacks.

Use of other types of cables may result in ﬁre.

• Be sure to observe the ampliﬁer’s rated load impedance (see page 4),

particularly when connecting speakers in parallel. Connecting an

impedance load outside the ampliﬁer's rated range can damage the

ampliﬁer.

• When choosing a power ampliﬁer to use with your speakers, make sure

that its power output matches the speakers’ power capacity (refer to the

Speciﬁcations on page 4). Even if the ampliﬁer’s power output is lower

than the speakers’ PGM (program) power capacity, the speakers may be

damaged when clipping of a high input signal occurs. The following

may cause damage to speakers:

- Feedback caused when using a microphone.

- Continuous high sound pressure level produced by electronic instruments.

- Continuous high-power output of distorted signals.

- Popping noises caused by turning on equipment, or by connecting or

disconnecting system components while the ampliﬁer is turned on.

• When turning on the AC power in your audio system, always turn on the

power ampliﬁer LAST, to avoid speaker damage. When turning the

power off, the power ampliﬁer should be turned off FIRST for the same

reason.

• Do not operate this device at high volume levels or at a level that is

uncomfortable, since it is capable of producing sound levels that could

cause permanent hearing loss. If you experience any discomfort or

ringing in the ears, or suspect an hearing loss, you should consult an

audiologist.

Protective Circuit (poly switch)

All full-range loudspeakers are ﬁtted with a self-resetting poly switch that protects

the high-frequency driver from damage caused by excessive power. If a

loudspeaker cabinet loses high-frequency output, immediately remove power from

the unit and wait for two to three minutes. This should be long enough to allow the

poly switch to reset. Reapply power and check the performance of the high-

frequency driver before continuing, with the power reduced to a level that does not

cause the poly switch to interrupt the signal. (On the subwoofers, the poly switch

protects the woofer and a similar routine should be followed if the output is lost.)

• Use only Neutrik NL4FC plugs for connecting Speakon connectors.

* Illustrations in this manual are for explanatory purposes only, and may

not match the actual appearance of the product during operation.

* Company names and product names used in this Owner’s Manual are

trademarks or registered trademarks of their respective owners.

Before Making Connections

■ Phone Plug Wiring

Phone plugs for connection to the phone jack inputs should be wired as

shown on the right. Be sure to use proper speaker cable — NOT shielded

instrument or line cable — for all speaker connections.

■ Neutrik NL4FC Plug Wiring

If you will be using the Neutrik connectors for speaker input,

wire the plugs as shown to the right. Be sure to use proper

speaker cable — NOT shielded instrument or line cable — for all

speaker connections.

Connections

Handling caution

Special Notice

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device.

2– (NO USE)

2+ (NO USE)

1+ : HOT (+)

1– : COLD (–)

Neutrik NL4FC connector

■ Subwoofer Parallel-connection

The subwoofer A15W features four input/parallel connectors—two 1/4" phone jacks and two Neutrik NL4MP con-

nectors. Use either a phone jack or a Neutrik connector to receive input from your sound system/power ampliﬁer.

One of the spare connectors can be used to parallel-connect an additional main speaker (keeping in mind the imped-

ance considerations mentioned below).

■ Impedance Considerations

When connecting speakers in parallel be sure to check the rated load impedance of the power ampliﬁer. Most power

ampliﬁers are capable of safely driving speakers with minimum impedance of 8 ohms or 4 ohms. A pair of parallel-

connected 8-ohm speakers have a total impedance of 4 ohms. Two 8-ohm speakers can safely be paralleled on one

output. 4-ohm speakers, however, should not be parallel-connected with other speakers. These models can be con-

nected in parallel, however, if you are using a power ampliﬁer that can safely drive load impedances of 2 ohms or

lower. Check your speaker impedance in the table below.

Speciﬁcations

*: EIA RS-426

Model A10 A12 A15 A12M A15W

Type

2 way Bass reﬂex

Bass reﬂex

Speaker Unit

10" cone 12" cone 15" cone 12" cone 15" cone

1" VC, Horn-TW —

Frequency Response

65 Hz-20 kHz 60 Hz-20 kHz 65 Hz-20 kHz

50 Hz-200 Hz

with the internal low

pass ﬁltering

Power Capacity

NOISE*

125 W 150 W 200 W 150 W 250 W

PGM

250 W 300 W 400 W 300 W 500 W

MAX

500 W 600 W 800 W 600 W 1000 W

Nominal Impedance

Ω

Sensitivity

96 dB SPL (1 W, 1 m) 97 dB SPL (1 W, 1 m) 98 dB SPL (1 W, 1 m) 97 dB SPL (1 W, 1 m) 97 dB SPL (1 W, 1 m)

Input Connectors

1/4" phone jack

× 1, Neutrik SPEAKON NL4MP

× 1

1/4" phone jack

× 2,

Neutrik SPEAKON

NL4MP

× 2

Socket Mount Diameter

35 mm (1 - 3/8")

Dimensions (W

×H

×D)

385 mm

× 542 mm

307 mm

405 mm

× 582 mm

323 mm

470 mm

× 672 mm

375 mm

582 mm

× 405 mm

323 mm

485 mm

× 622 mm

485 mm

Weight

13.0 kg 15.5 kg 21.5 kg 15.5 kg 28.0 kg

77.5

102.5

120

A10/A12/A15 A12M A15W

Unit: mm

Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp.

reserves the right to change or modify products or speciﬁcations at any time without prior notice. Since speciﬁ-

cations, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

For details of products, please contact your nearest Yamaha

representative or the authorized distributor listed below.

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149,

Col. Guadalupe del Moral

C.P. 09300, México, D.F., México

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Av. Reboucas 2636-Pinheiros CEP: 05402-400

Sao Paulo-SP. Brasil

Tel: 011-3085-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Viamonte 1145 Piso2-B 1053,

Buenos Aires, Argentina

Tel: 1-4371-7021

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

THE UNITED KINGDOM

Yamaha-Kemble Music (U.K.) Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

GERMANY

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Central Europe GmbH,

Branch Switzerland

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Music Central Europe GmbH,

Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

THE NETHERLANDS

Yamaha Music Central Europe,

Branch Nederland

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

BELGIUM/LUXEMBOURG

Yamaha Music Central Europe GmbH,

Branch Belgium

Rue de Geneve (Genevastraat) 10, 1140 - Brussels,

Belgium

Tel: 02-726 6032

FRANCE

Yamaha Musique France

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.

Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha-Hazen Música, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: 91-639-8888

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1

Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Ofﬁce

Generatorvej 6A

DK-2730 Herlev, Denmark

Tel: 44 92 49 00

NORWAY

Norsk ﬁlial av Yamaha Scandinavia AB

Grini Næringspark 1

N-1345 Østerås, Norway

Tel: 67 16 77 70

OTHER EUROPEAN COUNTRIES

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2313

TURKEY/CYPRUS

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LB21-128 Jebel Ali Freezone

P.O.Box 17328, Dubai, U.A.E.

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

25/F., United Plaza, 1468 Nanjing Road (West),

Jingan, Shanghai, China

Tel: 021-6247-2211

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong,

Youngdungpo-ku, Seoul, Korea

Tel: 02-3770-0660

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-78030900

SINGAPORE

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building

140 Paya Lebor Road, Singapore 409015

Tel: 747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

891/1 Siam Motors Building, 15-16 ﬂoor

Rama 1 road, Wangmai, Pathumwan

Bangkok 10330, Thailand

Tel: 02-215-2626

OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2317

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2313

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

HEAD OFFICE

Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2441

PA11

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

410CR-01A0

Printed in China

Yamaha Pro Audio global web site

http://www.yamahaproaudio.com/

Yamaha Manual Library

http://www2.yamaha.co.jp/manual/english/

Yamaha A12M, A10, A12, A15, A15W Инструкция по применению

Похожие модели бренда