Yamaha RX-V1067 Инструкция по применению

Категория
Аудио-видео ресиверы
Тип
Инструкция по применению
1
3
2
2
within 6 m
- 1 -
English
Quick Reference Guide
for Asia*, Africa, Oceania
and Latin America
*Except for China and Korea
E.g. E.g.
Preparing the remote control
Accessories
Items necessary for connection
The following accessories are supplied with this product.
Speakers
External components
Remote control
Front speaker
E.g. E.g.
Batteries (2)
(AAA, R03, UM-4)
Center speaker
AM loop antenna
Surround speaker, surround back
speaker, and presence speaker
Indoor FM antenna
Active subwoofer
Power cable*
1
Take off the battery compartment cover.
2
Insert the two supplied AAA batteries
into the battery case, following the
polarity markings.
3
Snap the battery compartment cover
back into place.
Be sure to aim the remote control directly at the remote
control sensor on this unit during operation.
TV
Cable
Cables for connecting external components
(may differ depending on the components you are connecting)
• Speaker cables
(a quantity to match the number of speakers you are connecting)
Audio pin cable
(for subwoofer)
Playback device such as BD
(Blu-ray Disc)/DVD players
Use speakers with an impedance of at least 6Ω. 4Ω speakers can also be used as the front speakers. For more information on speaker
impedance, refer to page 3.
If you are using a CRT monitor, we recommend that you use magnetically shielded speakers.
Prepare at least two front speakers. The priority of the other speakers is as follows:
1 Two surround speakers
2 One center speaker
3 One (or two) surround back speaker(s)/presence speakers
YPAO microphone
* The  gure of the supplied power cable may differ depending upon regions.
7.1
6.1
7.1
- 2 -
Connect and install as follows the  rst time you use this unit.
See the following explanations for the connections for each number.
1
1
Connect the speakers
2
2
Connect a TV
3
3
Connect playback devices such as BD/DVD players and recorders
4
4
Set the VOLTAGE SELECTOR and connect the power cable
(General model)
Connect the power cable
(Other models)
5
5
Set up the speaker parameters automatically (YPAO)
This unit
TV
Subwoofer
1
1
1
1
2
2
3
3
4
4
BD/DVD player
(recorder)
Center speaker
Surround
speaker R
Surround
speaker L
Surround back
speaker L
Surround back
speaker
Surround back
speaker R
Front
speaker R
Front
speaker L
7.1
Connect when using with 7.1-channel speaker
layout. Place the surround back speakers
(L/R) 30 cm or more away from each other.
6.1
Connect when using with 6.1-channel speaker
layout. Place the surround back speaker
behind the listening position.
AC
SURROUND SURROUND BACK/
SPEAKERS
CENTER
AV 1 AV 2 AV 3 AV 4
HDMI
AV 5 AV 6 AV 7
SINGLE
FRONT
BI-AMP
AV 3
AV 4
F
RONT
SURROUND
SUR. BACK
SUBWOOFER
CENTER
MULTI CH INPUT
COMPONENT VIDEO
MONITOR OUT/ZONE OUT
ZONE OUT PRE OUT
ZONE 2
YP
B
P
R
P
B
P
R
YP
B
P
R
C
D
SURROUND
SUR. BACK
CENTER
SUBWOOFER
1
2
RS-232C
2
1
TRIGGER
OUT
+12V 0.1A MAX.
FRONT
(1 BD/DVD)
(SINGLE)
ZONE2/
F.PRESENCE
EXTRA SP
IN
OUT
REMOTE
A
C
S
P
E
K
E
R
S
A
V
A
A
1
A
V
A
A
2
A
V
A
A
3
A
V
A
A
4
H
D
M
I
A
V
A
A
5
A
V
A
A
6
A
V
A
A
7
A
V
A
A
3
A
V
A
A
4
F
R
O
N
T
S
U
R
R
O
U
N
D
S
U
R
.
B
A
C
K
S
U
B
W
O
O
F
E
R
C
E
N
T
E
R
M
U
L
T
L
L
I
C
H
I
N
P
U
T
C
O
M
P
O
N
E
N
T
V
I
D
E
O
M
O
N
I
T
O
R
O
U
T
/
T
T
Z
/
/
O
N
E
O
U
T
Z
O
N
E
O
U
T
P
R
E
O
U
T
Z
O
N
E
2
Y
P
B
P
R
P
B
P
R
Y
P
B
P
R
C
D
S
U
R
R
O
U
N
D
S
U
R
.
B
A
C
K
C
E
N
T
E
R
S
U
B
W
O
O
F
E
R
2
R
S
-
2
3
2
C
2
1
T
R
I
G
G
E
R
O
U
T
+
1
2
V
0
.
1
A
M
A
X
.
F
R
O
N
T
(
1
B
D
/
D
V
D
)
(
S
I
N
G
L
E
)
Z
O
N
E
2
/
F
.
F
F
P
R
E
S
E
N
C
E
E
X
T
R
A
S
P
I
N
O
U
T
R
E
M
O
T
E
6.1
7.1 7.1
- 3 -
1
1
Connect the speakers
Front speaker
R L
Subwoofer
Center speaker
R L
Surround back
speaker
R L
Surround
speaker
Connecting speakers
Connecting the subwoofer
1
Connect the subwoofer input jack to the
SUBWOOFER 1 jack on this unit with an audio
pin cable.
(
SINGLE
)
SUBWOOFER
PRE OUT
CENTER
CENTER
SUR. BACKSURRUND
1
2
FRONT
When connecting the presence speakers, refer to “Presence speaker
connection” in the Owner’s Manual.
This unit can connect speakers that support Bi-amp connection for front
speakers. Refer to “Bi-amp connection” in the Owner’s Manual.
7.1
Connect when using with 7.1-channel speaker layout.
6.1
Connect when using with 6.1-channel speaker layout.
2
Set the subwoofer volume as follows.
Volume: Set to approximately half volume (or slightly less than half).
Crossover frequency (if available): Set to maximum.
Subwoofer examples
VOLUME
MIN MAX
CROSSOVER/
HIGH CUT
MIN MAX
Caution:
Remove the power cable of this unit from the power outlet before
connecting the speakers.
Generally speaker cables consist of two parallel insulated
cables. One of these cables is a different color, or has a line
running along it, to indicate different polarity. Insert the different
colored (or lined) cable into the “+” (positive, red) terminal
on this unit and the speakers, and the other cable into the “-”
(minus, black) terminal.
Be careful that the core of the speaker cable does not touch
anything or come into contact with the metal areas of this unit.
This may damage this unit or the speakers. If the speaker cables
short circuit, “CHECK SP WIRES!” will appear on the front panel
display when this unit is switched on.
This unit is con gured for 8Ω speakers at the factory setting.
When connecting 6Ω speakers, con gure the speaker impedance
setting of this unit to 6Ω. When this unit is con gured for 6Ω
speakers, 4Ω speakers can also be used as the front speakers.
For more information on setting the speaker impedance, refer to
“Changing speaker impedance” in the Owner’s Manual.
FRONT
-
2
2
3
1
4
4
+
1
Remove approximately 10 mm of insulation from
the ends of the speaker cables, and twist the bare
wires of the cables together  rmly so that they will
not cause short circuits.
2
Loosen the speaker terminals.
3
Insert the bare wire of the speaker cable into the
gap on the side of the terminal.
4
Tighten the terminal.
SURROUND SURROUND BACK/
SPEAKERS
C
AV 1
HDMI OUT
AV 2 AV 3 AV 4
HDMI
AV 5
SINGLE
BI-AMP
12
AV 3
AV 4
C
AL
OPTICAL
AUDIO 1
(2 TV)
(3 CD)
AUDIO 2 AUDIO 3 AUDIO 4
FRONT
SURROUND
SUR. BACK
SUBWOOFER
CENTER
MULTI CH INPUT
COMPONENT VIDEO
COAXIAL
MONITOR OUT/ZONE OUT
ZONE OUT PRE OUT
ZONE 2
AV OUT
YP
B
P
R
YP
B
P
R
YP
B
P
R
C
D
SURROUND
SUR. BACK
MON.OUT/ZONE OUT
ARC ARC
SELECTABLE
FRONT
(1 BD/DVD)
AV 1
AV 2
B
A
Ԝԝ
(SINGLE)
IN
RE
M
S
U
R
R
O
U
N
D
S
U
R
R
O
U
N
D
B
A
C
K
/
KK
S
P
E
A
K
E
R
S
C
A
V
A
A
1
A
V
A
A
2
A
V
A
A
3
A
V
A
A
4
H
D
M
I
A
V
A
A
5
S
I
N
G
L
E
B
I
-
A
M
P
A
V
A
A
3
A
V
A
A
4
C
A
L
O
P
T
I
C
A
L
A
U
D
I
O
1
(
2
T
V
)
(
3
C
D
)
A
U
D
I
O
2
A
U
D
I
O
3
A
U
D
I
O
4
F
R
O
N
T
S
U
R
R
O
U
N
D
S
U
R
.
B
A
C
K
S
U
B
W
O
O
F
E
R
C
E
N
T
E
R
M
U
L
T
L
L
I
C
H
I
N
P
U
T
C
O
M
P
O
N
E
N
T
V
I
D
E
O
C
O
A
X
I
A
L
Z
O
N
E
O
U
T
P
R
E
O
U
T
Z
O
N
E
2
A
V
A
A
O
U
T
Y
P
B
P
R
Y
P
B
P
R
C
D
S
U
R
R
O
U
N
D
S
U
R
.
B
A
C
K
F
R
O
N
T
(
1
B
D
/
D
V
D
)
A
V
A
A
1
A
V
A
A
2
B
A
Ԝ
ԝ
(
S
I
N
G
L
E
)
I
N
R
E
M
VIDEO
S VIDEO
COMPONENT
VIDEO
HDMI
HDMI
HDMI
Y
P
R
P
R
Y
P
B
P
B
V
V
S
S
* For details on selecting the active HDMI OUT jack, refer to “Selecting the active HDMI OUT jack” in the Owner’s Manual.
A When the HDMI input
is available.*
B When the component
video input is available.
C
When the S-video input is
available.
D
When only the video input
is available.
- 4 -
2
2
Connect a TV
Listening to TV audio
To play back TV audio on this unit, connect the TV audio output to this unit.
Connect the following input jacks, matching the audio output jacks on your TV.
When viewing your TV, select the appropriate input source on this unit.
HDMI OUT
12
O
(1 BD/DVD)
AV 1
KNETWORK
AV 2 AV 3 AV 4
COAXIAL COAXIAL
OPTICAL OPTICAL
OPTICAL
AUDI O 1
(2 TV)
(3 CD)
AUDIO 2 AUDIO 3 AUDIO 4
COAXIAL
AV O UT
Y
MON.OUT/ZONE OUT
ARC ARC
SELECTABLE
AV 1
AV 2
B
A
ԘԙԚԛ Ԝԝ
ANTENNA
75
GND
AMFM
(4 RADIO)
O
(
1
B
D
/
D
V
D
)
A
V
A
A
1
K
N
E
T
W
O
R
K
A
V
A
A
2
A
V
A
A
3
A
V
A
A
4
C
O
A
X
I
A
L
C
O
A
X
I
A
L
O
P
T
I
C
A
L
O
P
T
I
C
A
L
A
V
A
A
O
U
T
Y
M
O
N
.
O
U
T
/
T
T
Z
/
/
O
N
E
O
U
T
A
V
A
A
1
A
V
A
A
2
B
A
Ԙ
ԙ
Ԛ
ԛ
A
N
T
E
N
N
A
7
5
G
N
D
A
M
F
M
(
4
R
A
D
I
O
)
OPTICAL
O
O
Audio
output
Audio output from TV Input jack on this unit
Optical digital output
AUDIO1
Coaxial digital output
AUDIO2
Analog output
AUDIO1
,
AUDIO2
, AUDIO3, or AUDIO4
HDMI Audio Return Channel
(Described in the right column)
HDMI OUT1 or HDMI OUT2
Connecting to AUDIO1 allows you to playback TV audio just by pressing
the SCENE2 key.
When using a TV that supports the Audio Return Channel
function and HDMI Control function
When using an HDMI compatible TV that supports
Audio Return Channel functions and / or HDMI Control functions
(e.g., Panasonic VIERA Link), you can enjoy the TV sound on this
unit.
The audio / video output from the unit to the TV and audio output
from the TV to the unit are possible using a single HDMI cable.
The input source is switched automatically to match operations
carried out on the TV, and that makes TV sound control easier to
use.
For the connections and settings, refer to “Using the HDMI Control
function” in the Owner’s Manual.
If your TV has multiple inputs, connect with the following priority (A to D).
When connecting to an HDMI compatible TV
Video signal such as component video, S-video and video received by
this unit is converted to HDMI and output to the TV. Just select HDMI
input on the TV to view video from any external source connected to
this unit.
HDMI
COMPONENT
VIDEO
HDMI
VIDEO
S VIDEO
Input Output
HDMI input
Through
Converted
TV
For more information on video signal conversion, refer to “Connecting a TV monitor” in the Owner’s Manual.
When connecting to a non-HDMI compatible TV
Connect to the TV using the same type of connection that you used to
connect to the playback device.
If the playback device and TV are equipped with different types of
analog video jacks, this unit will convert the video signals to another
type of video signal according to the type of video input jacks used
on the TV.
COMPONENT
VIDEO
HDMI
VIDEO
COMPONENT
VIDEO
HDMI
VIDEO
S VIDEO
S VIDEO
Input Output
Component
video input
S-video input
Video input
Through
Converted
TV
Refer “Connecting BD/DVD players and other devices” in Owner’s Manual for details on connection other than above illustration.
When playing back a device, select the corresponding input source to which the jack is connected.
If necessary, you can connect components that cannot be connected using the above methods, such as devices that output video from
component video output jacks and audio from analog output jacks. Refer to “Connecting external components” in the Owners Manual for details.
At the default settings, input sources and sound programs are preset on the SCENE keys. When a playback device is connected to AV1,
pressing the SCENE1 key selects the AV1 input. When a playback device is connected to AUDIO2, pressing the SCENE3 selects the AUDIO2
input. The input source and sound program preset on the SCENE key can be changed.
Default scene settings
SCENE Input Audio Select HDMI Output
Sound
Program
Pure Direct
Mode
Tone Control Adaptive DRC Enhancer
1 (BD/DVD) AV1 Auto OUT1+2 Drama Auto
Bass:0.0dB
Trebele:0.0dB
On Off
2 (TV) AUDIO1 Auto OUT1+2 STRAIGHT Auto
Bass:0.0dB
Trebele:0.0dB
On On
3 (CD) AUDIO2 Auto OUT1+2 STRAIGHT Auto
Bass:0.0dB
Trebele:0.0dB
Off Off
4 (RADIO) TUNER --- OUT1+2 STRAIGHT Auto
Bass:0.0dB
Trebele:0.0dB
Off On
The several settings other than ones in the above table can be assigned to the SCENE keys. For more information on the SCENE function, refer to “Changing input
settings with a single key (SCENE function)” in the Owner’s Manual.
AUDIO
VIDEO
COMPONENT
VIDEO
COAXIAL
OPTICAL
COMPONENT
VIDEO
HDMI
ANTENNA
75
GND
AMFM
(4 RADIO)
SURROUND
AV 1
HDMI OUT
AV 2 AV 3
12
PHONO
GND
(1 BD/DVD)
AV 1
DOCK NETWORK
AV 2 AV 3 AV 4
AV 3
AV 4
COAXIAL COAXIAL
OPTICAL OPTICAL
OPTICAL
AUDI O 1
(2 TV)
(3 CD)
AUDIO 2 AUDIO 3 AUDIO 4
FRONT
SURROUND
SUR. BACK
SUBWOOFER
CENTER
MULTI CH INPUT
COMPONENT VIDEO
COAXIAL
ZON
E
ZONE 2
AV OUT
YP
B
P
R
YP
B
P
R
C
D
MON.OUT/ZONE OUT
ARC ARC
SELECTABLE
(1 BD/DVD)
AV 1
AV 2
B
A
ԘԙԚԛ Ԝԝ
A
N
T
E
N
N
A
7
5
G
N
D
A
M
F
M
(
4
R
A
D
I
O
)
S
U
R
R
O
U
N
D
H
D
M
I
O
U
T
A
V
A
A
2
A
V
A
A
3
1
2
P
H
O
N
O
G
N
D
(
1
B
D
/
D
V
D
)
A
V
A
A
1
D
O
C
K
N
E
T
W
O
R
K
A
V
A
A
2
A
V
A
A
3
C
O
A
X
I
A
L
O
P
T
I
C
A
L
O
P
T
I
C
A
L
A
U
D
I
O
1
(
2
T
V
)
(
3
C
D
)
A
U
D
I
O
2
A
U
D
I
O
3
A
U
D
I
O
4
F
R
O
N
T
S
U
R
R
O
U
N
D
S
U
R
.
B
A
C
K
S
U
B
W
O
O
F
E
R
C
E
N
T
E
R
M
U
L
T
L
L
I
C
H
I
N
P
U
T
C
O
M
P
O
N
E
N
T
V
I
D
E
O
C
O
A
X
I
A
L
Z
O
N
E
Z
O
N
E
2
A
V
A
A
O
U
T
Y
P
B
P
R
A
V
A
A
4
D
M
O
N
.
O
U
T
/
TT
Z
/
/
O
N
E
O
U
T
A
R
C
A
R
C
S
E
L
E
C
T
A
T
T
B
L
E
A
V
A
A
1
A
Ԙ
ԛ
Ԝ
ԝ
O
R
R
C
V
V
L
L
O
C
O
P
R
Y
P
R
YP
B
HDMI
HDMI
P
B
P
B
P
B
P
R
Y
P
R
Y
A
When the HDMI output is
available.
B
When the component video
output is available (with optical
digital audio output).
C
When the component video
output is available (with coaxial
digital audio output).
D
When only the video input
is available (with the analog
audio output).
- 5 -
3
3
Connect playback devices such as BD/DVD players and recorders
If your playback device has multiple audio/video outputs, connect with the following priority
(A to D) to enjoy a higher quality sounds and images.
Plug the supplied
power cable into
the AC inlet after all
other connections
are complete, then
plug the power
cable into an AC
wall outlet.
AC IN
RS-232C
2
1
T
RIGGER
OUT
V
0.1A MAX.
ZONE2/
F.PRESENCE
EXTRA SP
A
C
I
N
R
S
-
2
3
2
C
2
1
T
R
I
G
G
E
R
O
U
T
V
0
.
1
A
M
A
X
.
Z
O
N
E
2
/
F
.
F
F
P
R
E
S
E
N
C
E
E
X
T
R
A
S
P
VOLTAGE SELECTOR
110V-
120V
220V-
240V
VOLTAGE SELECTOR
(General model only)
Select the switch position according to your local
voltage using a straight slot screwdriver.
Voltages are AC 110-120/220-240 V, 50/60 Hz.
Caution
The VOLTAGE SELECTOR on the rear
panel of this unit must be set for your local
voltage BEFORE plugging the power cable
into the AC wall outlet. Improper setting of the
VOLTAGE SELECTOR may cause damage
to this unit and create a potential  re hazard.
4
4
Set the VOLTAGE SELECTOR and connect the power cable
(General model)
Connect the power cable (Other models)
AC IN
RS-232C
2
1
T
RIGGER
OUT
V
0.1A MAX.
ZONE2/
F.PRESENCE
EXTRA SP
R
S
-
2
3
2
C
2
1
T
R
I
G
G
E
R
O
U
T
V
0
.
1
A
M
A
X
.
Z
O
N
E
2
/
F
.
F
F
P
R
E
S
E
N
C
E
E
X
T
R
A
S
P
Power cable
To the AC wall outlet
Continues to
the next page
- 6 -
When all connections are complete, adjust the con guration, sizes, and volume
balance of the speakers to provide an optimal sound  eld. This unit is equipped with a
Yamaha Parametric Room Acoustic Optimizer (YPAO) function that adjusts the speaker
balance automatically with a simple procedure.
Be aware of the following when using YPAO.
The amount of time for measurement varies from about two to ten minutes according to settings.
The test tone is output at high volume. Refrain from using this function at night when it may be a nuisance to others.
Take care that the test tone does not frighten small children.
YPAO operations can be viewed on the front panel display or TV screen. TV display is used here to explain operation.
1
Check the following before using YPAO.
This unit
The headphones are removed.
TV
This unit is connected to the TV correctly.
The power is turned on.
The video input to which the video output
from this unit has been selected.
Subwoofer
The power is turned on.
Volume is set to approximately half, and the
cross-over frequency (if present) is set to
maximum.
2
Place the supplied YPAO microphone at ear height in your listening
position.
When positioning the microphone, we recommend that you use equipment that allows you
to adjust the height (such as a tripod) as a microphone stand. When using a tripod, use the
tripod screws to  x the microphone in place.
Measuring, for multiple listening positions, is also available. For more information, refer to
“Setting up the speaker parameters automatically (YPAO)” in the Owner’s Manual.
3
Press RECEIVER A on the remote control to switch this unit on.
4
Connect the YPAO microphone to the YPAO MIC jack on the front panel.
YPAO microphone
“Mic On View ON SCREEN”
appears on the front panel
display, and the display at right
appears on the TV screen.
YPAO can be performed
viewing only front panel display
on this unit without the TV
screen.
Opening and closing the front panel door
Before step 4, gently press the bottom of the door to open it.
Keep the door closed when not using controls or jacks behind the
front panel door.
This completes preparation. To achieve more accurate results, take note of the
following when measuring acoustics.
Keep the room as quiet as possible for a few minutes.
Wait in a corner of the room, or leave it entirely, while acoustics are measured to
avoid creating an obstruction between the speakers and the YPAO microphone.
5
5
Set up the speaker parameters automatically (YPAO)
YPAO microphone
VOLUME
MIN MAX
CROSSOVER/
HIGH CUT
MIN MAX
Subwoofer examples
- 7 -
SCENE
VOLUME
ENHANCER
SUR. DECODE
STRAIGHTSLEEP PURE DIRECT
AV
AUDIO
1234
75
FM
INFO
MEMORY
AM
PRESET
PA RT Y
MOVIE MUSIC
MUTE
ENTER
7856
90
10
1234
REC
ENT
TV
TV VOL TV CH
TOP
MENU
POP-UP
MENU
SOURCE
MAIN
ZONE 2
RECEIVER
CODE SET
INPUT
MUTE
DOCK
HDMI OUT
MULTI
1234
6
V-AUX
USB
NET
TUNER
PHONO
TUNING
ON SCREEN OPTION
1
2
3
4
BD/DVD
TV
CD
RADIO
1
2
3
4
BD/DVD
TV
CD
RADIO
RETURN
DISPLAY
S
C
E
N
E
V
O
L
U
M
E
E
N
H
A
N
C
E
R
S
U
R
.
D
E
C
O
D
E
S
T
R
A
I
G
H
T
P
U
R
E
D
I
R
E
C
T
M
O
V
I
E
M
U
S
I
C
M
U
T
E
7
8
5
6
9
0
1
0
1
2
3
4
R
E
C
E
N
T
T
V
T
V
V
O
L
T
V
C
H
T
O
P
M
E
N
U
P
O
P
-
U
P
M
E
N
U
S
O
U
R
C
E
M
A
I
N
Z
O
N
E
2
R
E
C
E
I
V
E
R
C
O
D
E
S
E
T
S
L
E
E
P
P
A
P
P
R
T
Y
F
M
I
N
F
O
M
E
M
O
R
Y
A
M
P
R
E
S
E
T
A
U
D
I
O
A
V
A
A
1
2
3
4
7
5
I
N
P
U
T
M
U
T
E
D
O
C
K
H
D
M
I
O
U
T
M
U
L
T
L
L
I
1
2
3
4
6
V
-
V
V
A
U
X
U
S
B
N
E
T
T
U
N
E
R
P
H
O
N
O
T
U
N
I
N
G
O
N
S
C
R
E
E
N
O
P
T
I
O
N
1
1
2
2
3
3
4
4
B
B
D
D
/
/
D
D
V
V
D
D
T
T
V
V
C
C
D
D
R
R
A
A
D
D
I
I
O
O
R
E
T
U
R
N
D
I
S
P
L
A
Y
A
A
RECEIVER A
ENTER, Cursor
5
Use the cursor B/C to select the “Measure and press ENTER to start
measurement.
When “Multi Position” is set to “Yes” (default), the
measurement of multiple positions will follow. Refer to
“Setting up the speaker parameters automatically (YPAO)”
for details on “Multi Position” in the Owner’s Manual.
The display at right appears if measurement  nishes
without any problems.
Result
Displays the results of automatic acoustics measurement.
For details, refer to “Reviewing the automatic setup
parameters” in the Owner’s Manual.
Save/Exit
Applies the result to the speaker setup and  nishes the
automatic measurement.
Note
If a problem occurs, an error message or report is displayed either during or after acoustic
measurement. Refer to “When an error message is displayed during measurement, or “When a
warning message is displayed after measurement” in the Owner’s Manual to resolve the problem
and measure acoustics with YPAO again.
6
Use the cursor B/C to select “Save/Exit” and press ENTER.
7
Use the cursor D/E to select “SAVE” and press ENTER.
When the display at right appears, the YPAO setup is
complete.
8
Press ENTER.
YPAO is terminated. Disconnect the YPAO microphone.
All the preparation is completed.
Enjoy the various functions provided by this unit. For details on the operations, refer to the Owners
Manual.
SCENE
VOLUME
ENHANCER
SUR. DECODE
STRAIGHTSLEEP PURE DIRECT
AV
AUDIO
1234
75
FM
INFO
MEMORY
AM
PRESET
PARTY
MOVIE MUSIC
MUTE
ENTER
7856
90
10
1234
REC
ENT
TV
TV VOL TV CH
TOP
MENU
POP-UP
MENU
SOURCE
MAIN
ZONE 2
RECEIVER
CODE SET
INPUT
MUTE
DOCK
HDMI OUT
MULTI
1234
6
V-AUX
USB
NET
TUNER
PHONO
TUNING
ON SCREEN OPTION
1
2
3
4
BD/DVD
TV
CD
RADIO
1
2
3
4
BD/DVD
TV
CD
RADIO
RETURN
DISPLAY
- 8 -
A
Switches this unit between on and standby mode
This unit switches between on and standby mode every time you press this key.
B
Selects an input source to listen to
The name of the selected input source appears on the front panel display.
VOLUME
A.Sel: AUTO
AV1
C
Selects a scene
You can switch the settings such as input sources and sound  eld programs with a single key.
Refer to “Default scene settings” on page 5 for details on the settings assigned to this unit.
D
Adjusts the volume level
The current volume level is displayed on the front panel display.
VOLUME
Main Volume
E
Mutes the sound
The MUTE indicator blinks while the sound is muted.
F
Selects sound 
eld programs and sound decoders
Front
panel
Remote
control
Description
MOVIE
Selects sound  eld programs optimized for appreciating music.
MUSIC
Selects sound  eld programs optimized for viewing movies,
dramas, and sports.
SUR. DECODE
Selects surround decoders such as Dolby Pro Logic II.
STRAIGHT
Switches to Straight decoding mode for stereo/multi-channel
playback without using a sound  eld program.
PURE DIRECT
PURE DIRECT
Switches to Pure Direct Mode for faithful reproduction of audio.
G
Turns on Compressed Music Enhancer
Press ENHANCER to turn on Compressed Music Enhancer for playback of the compressed music
source with better sound quality.
VOLU ME
ENHANCER
Enhancer On
To disable Compressed Music Enhancer, press ENHANCER again.
Basic operations
© 2010 Yamaha Corporation
YC597A0/QREN1
Owner’s Manual
AV Receiver English for Asia*, Africa, Oceania
and Latin America
*Except for China and Korea
En 2
BEFORE USE
About this manual
Supplied accessories
Check that you received all of the following parts.
Remote control
Batteries (AAA, R03, UM-4) x 2
Power cable
YPAO microphone
AM loop antenna
Indoor FM antenna
Language selection
This procedure allows you to select the language of
menus and messages on the TV screen.
1
Press jON SCREEN to display the ON
SCREEN menu.
2
Press kCursor B / C to select “Setup” and
press kENTER.
3
Press kCursor D / E to select the
“Language” and press kENTER.
4
Press kCursor B / C to select the favorite
language from the following options.
5
Press jON SCREEN to close the ON
SCREEN menu.
jON SCREEN
kCursor B / C / D / E
kENTER
ENTER
ON SCREEN
SCEN
E
VO
L
U
ME
MUTE
ENHANCE
R
SU
R. DE
CO
D
E
STRAIGH
T
PURE DIRECT
MOVI
E
MUSI
C
SLEE
P
P
ARTY
FM
INFO
M
EMORY
AM
PRESE
T
AUDI
O
AV
1
2
3
4
7
5
7
8
5
6
9
0
10
1
2
3
4
R
EC
ENT
T
OP
MENU
P
OP-U
P
MENU
SOU
R
C
E
MAIN
Z
O
NE 2
RE
C
EIVER
CODE SET
INPUT
MU
T
E
D
OCK
HDMI
O
UT
MULTI
1
2
3
4
6
V-AU
X
U
SB
NET
TUNER
P
HON
O
TUNING
O
PTIO
N
1
1
2
2
3
3
4
4
BD
/
DVD
BD/DVD
TV
TV
CD
CD
RADI
O
RADIO
RETURN
D
ISPLAY
k
j
Some features are not available in certain regions.
This manual is created prior to production. Design and
specifications are subject to change in part as a result
of improvements, etc. In case of differences between
the manual and product, the product has priority.
jON SCREEN” (example) indicates the name of
the parts on the remote control. Refer to the “Remote
control” (
p. 12) for the information about each
position of the parts.
J
1 indicates that the reference is in the footnote.
Refer to the corresponding numbers on the bottom of
the page.
indicates the page describing the related
information.
Click on the “ ” at the bottom of the page to
display the corresponding page in “Part names and
functions.
Front panel
Rear panel
Front panel display
Remote control
English (English), (Japanese),
(French), (German), (Spanish),
(Russian)
En 3
CONTENTS
INTRODUCTION
Features and capabilities...................................................5
Using the TV OSD to operate the unit.............................6
Basic operation of OSD menu..........................................6
Viewing or modifying content
for the current input source <Content window>...............6
Configuring settings for this unit
<ON SCREEN menu>......................................................6
Adjust settings for each input source
<Option menu>.................................................................7
Part names and functions..................................................8
Front panel........................................................................8
Front panel with the cover opened ...................................9
Rear panel.......................................................................10
Front panel display.........................................................11
Remote control ...............................................................12
Remote control (sequel) .................................................13
On-screen display...........................................................14
CONNECTIONS
Connecting speakers........................................................15
Speaker channels and functions......................................15
Speaker layout................................................................16
Connecting speakers and subwoofers.............................19
Advanced speaker configuration....................................22
Speaker layout utilizing an external power amplifier.....22
Connecting an external amplifier ...................................22
Connecting external components....................................23
Jacks and cables..............................................................23
Connecting a TV monitor...............................................24
Connecting BD/DVD players and other devices............27
Connecting game consoles or video camcorders............32
Connecting a multi-format player
or an external decoder ....................................................32
Connecting a SCENE link
playback-compatible device...........................................33
Using the Trigger function to link external component
power..............................................................................33
Connecting audio/video recording devices....................34
Connecting to the network .............................................34
Connecting a USB storage device..................................35
Connecting the FM/AM antennas..................................36
Setting up the speaker parameters automatically
(YPAO)..............................................................................37
PLAYBACK
Basic playback procedure...............................................44
Changing input settings with a single key
(SCENE function)............................................................46
Selecting the SCENE suitable
for the external component.............................................46
Enjoying favorite sound field effect ...............................47
Selecting sound programs and sound decoders..............47
Enjoying spatial sound
with the CINEMA DSP function ...................................47
Enjoying unprocessed playback
(Straight decoding mode)...............................................48
Enjoying Hi-Fi Sound Quality (Pure Direct Mode)....... 49
Enjoying stereo playback...............................................49
Enjoying compressed music source with better sound
quality (Compressed Music Enhancer)..........................49
Sound programs..............................................................50
Controlling this unit while viewing the TV screen .......52
Basic operations via the TV screen display ...................52
Configuring settings specific to an individual input
source (Option menu)......................................................54
Option menu display and setup......................................54
Option menu...................................................................55
Confirming and operating input sources from the
content window................................................................58
Displaying the content window on the TV screen .........58
Switching the display between the Now Playing view
and the Browse view ......................................................58
FM/AM tuning................................................................. 59
Selecting a frequency for reception (Normal tuning) .... 59
Navigating the FM/AM tuner
from the content window ............................................... 61
Playing back tunes on the PC......................................... 63
Windows Media Player setup......................................... 63
Playback of PC music contents...................................... 63
Playing back tunes on the USB storage devices............ 65
Playback of the USB storage device.............................. 65
Listening to the Internet Radio...................................... 67
Listening to Internet Radio ............................................ 67
Using shortcut function................................................... 69
Playing back tunes from your iPod™/iPhone™........... 70
Connecting the Universal Dock for iPod....................... 70
Controlling an iPod™/iPhone™.................................... 70
Playing iPod™/iPhone™ from the menu screen
(Menu browse control)................................................... 71
Operating basic playback functions
via the remote control (Simple remote control)............. 72
Playing iPod™/iPhone™ with wireless connection...... 72
Playing back tunes from Bluetooth™ components ...... 74
Connecting a Yamaha Bluetooth Wireless Audio
Receiver.......................................................................... 74
Pairing Bluetooth™ components................................... 74
Using Bluetooth™ components..................................... 75
Controlling this unit by using the Web browser
(Web Control Center)...................................................... 76
Displaying and Operating Web Control Center............. 76
En 4
SETUP
Configuring input sources (Input menu).......................78
Configuring input sources ..............................................78
Input menu......................................................................79
Editing the SCENE function (Scene menu)...................81
Editing a scene................................................................81
Scene menu.....................................................................82
Simple registering as the SCENE...................................83
Setting sound program parameters
(Sound Program menu)...................................................84
Editing sound programs..................................................84
CINEMA DSP parameters .............................................85
Parameters usable in certain sound programs ................87
Parameters usable in surround decoder..........................88
Setting various functions (Setup menu).........................89
Operating the Setup menu ..............................................89
Setup menu.....................................................................90
Manages settings for speakers........................................90
Setting the audio output function of this unit.................94
Setting this unit’s video output function.........................96
Setting HDMI functions.................................................97
Adjusting this unit’s network parameters.......................99
Setting this unit’s multi-zone function .........................100
Making the receiver easier to use .................................101
Language ......................................................................104
Confirming information of this unit
(Information menu) .......................................................105
Selecting information ...................................................105
Controlling the remote control to operate various
functions..........................................................................107
Keys connecting external components .........................107
Default remote control code settings............................107
Registering remote control codes
for external component operations...............................108
Resetting all remote control codes ...............................109
Extended functionality that can be configured
as needed (Advanced Setup menu)...............................110
Displaying/Setting the Advanced Setup menu.............110
Setting the impedance of speakers...............................110
Remote sensor..............................................................110
Avoiding crossing remote control signals
when using multiple Yamaha receivers........................111
Changing FM/AM frequency steps
(Asia and General models only)...................................111
Changing TV format ....................................................111
Removing HDMI video output up-scaling limits......... 112
Recovery and backup of the system settings................112
Initializing various settings for this unit.......................112
Firmware update...........................................................113
Firmware version.......................................................... 113
Using the HDMI Control function ...............................114
Enjoying the contents in another room .......................118
Connecting Zone2........................................................118
Controlling Zone2........................................................120
Enjoying the music in all rooms...................................120
APPENDIX
Troubleshooting .............................................................121
General.........................................................................121
HDMI™ .......................................................................123
Tuner (FM/AM) ........................................................... 124
USB and Network ........................................................125
iPod™/iPhone™ ..........................................................126
Bluetooth™..................................................................127
Remote control.............................................................127
Glossary..........................................................................128
Audio information........................................................128
Sound program information.........................................129
Video information ........................................................130
Compatibility of the input
and output video signals...............................................130
Information on HDMI™............................................... 131
About trademarks ......................................................... 132
Specifications.................................................................. 133
Index............................................................................... 135
En 5
INTRODUCTION
Built-in high-quality, high-power 7-channel amplifier
Multi-channel speaker configuration capability
2- to 7.1-channel speaker configurations.................................................................................................16
Presence speaker connections for playback with a richer sound field effect...........................................19
Bi-amplification connections for high-quality playback .........................................................................20
External amplifier connections for high-quality playback and expansion of channels ...........................22
Speaker impedance configuration............................................................................................................20
HDMI compatibility
8 HDMI input jacks (7 on the rear, 1 on the front) supporting 3D video signal input ............................27
2 selectable HDMI output jacks supporting Audio Return Channel and 3D video signal......................25
Automatic setup for speaker acoustic parameters
(YPAO - Yamaha Parametric Room Acoustic Optimizer) ......................................37
Extensive inputs (max. 13) for external playback components
BD/DVD/CD player connection..............................................................................................................27
Game console / video camcorder connection ..........................................................................................32
Multi-format player / external decoder connection .................................................................................32
iPod/iPhone wired connection.................................................................................................................70
iPod/iPhone wireless connection.............................................................................................................72
Bluetooth component connection ............................................................................................................74
1-button input/sound program/setting switching (SCENE function)...................46
Built-in sound programs and surround decoders for playback variety of sources
Spatial sound playback with sound field effects (CINEMA DSP)..........................................................47
Playback with no sound field effects (straight decoding)........................................................................48
High-fidelity sound playback (Pure Direct).............................................................................................49
Enhanced sound playback for compressed sources (Compressed Music Enhancer)...............................49
Tuner playback
FM/AM broadcast....................................................................................................................................59
(Asia and General models only) Changing FM/AM frequency steps......................................................59
Playback and control via network
Playback of music on the PC and DLNA server......................................................................................63
Internet radio service playback................................................................................................................67
Control this unit via network (Web Browser Control).............................................................................76
Playback of music on the USB storage devices................................................... 65
Sophisticated on-screen display (OSD) for easy operation
Selection of input sources, scenes, and sound programs.........................................................................52
Navigation for the current input source (content window)......................................................................58
Setup for this unit (ON SCREEN menu).................................................................................................78
Setup for each input source (Option menu).............................................................................................54
Customizable remote control
Remote control code setup for operation of external components ........................................................107
Multi-room listening capability (Zone2)............................................................... 118
Features and capabilities
Most of functions can be operated with on-screen display on the TV screen. Refer to “Using the TV
OSD to operate the unit” on the following pages for information on functions that can be controlled
using the on-screen display.
INTRODUCTION
En 6
This unit features a sophisticated on-screen display (OSD) for the TV screen. The OSD is designed to enable visual guidance that simplifies operations. The OSD mainly displays the ON SCREEN and
Option menus, as well as the content window that displays the content of current input sources.
Basic operation of OSD menu
Select an input source, scene and sound program
Select an input source..............................................................................................................................52
Select a scene...........................................................................................................................................52
Select a sound program............................................................................................................................53
Select a language
Change the language displayed on the TV screen <Language>............................................................104
Viewing or modifying content for the current input source
<Content window>
Operate the FM/AM tuner
Display preset stations for selection ........................................................................................................61
Display information on the station currently received.............................................................................61
Perform operations such as searching for and registering stations using the screen buttons ..................61
Operate the Internet radio
Display information on the station currently received.............................................................................67
Play back the radio contents ....................................................................................................................67
Bookmark Internet radio stations.............................................................................................................67
Operate the iPod music sources
Display the list of iPod music sources for selection ................................................................................71
Perform operations such as play, stop and pause using the TV screen <Menu browse control> ............71
Configuring settings for this unit <ON SCREEN menu>
Configure an input source
Change the input source name <Rename/Icon Select> ...........................................................................79
Specify a format for digital audio signals <Decoder Mode> ..................................................................80
Enhance the sound of compressed audio <Enhancer> ............................................................................80
Output a video signal input from another input source
while playing a multi-channel audio signal <Video Out>.......................................................................80
Charge the iPod/iPhone when this unit is in standby mode <Standby Charge>......................................80
Play the music sources on PC with the external control <DMC Control>..............................................80
Customize a scene
Register or clear settings for a selected scene <Save>, <Load>, <Reset> ........................................82, 83
Turn on a Yamaha BD/DVD player or CD player connected to this unit automatically
when a scene is selected <SCENE IR> ...................................................................................................82
Changing a scene name and icon <Rename/Icon Select> .......................................................................83
Adjust a sound program (sound program)
Adjust sound program parameters...........................................................................................................84
Display settings information for this unit
Display audio signal information <Audio Signal>................................................................................105
Display video signal information <Video Signal> ................................................................................105
Display HDMI signal information <HDMI Monitor>...........................................................................105
Display network information <Network>..............................................................................................106
Display system information <System>..................................................................................................106
Display Zone information <Zone>........................................................................................................106
Using the TV OSD to operate the unit
Continues to the
next page
INTRODUCTION
Using the TV OSD to operate the unit
En 7
Adjust acoustic parameters to match your speakers and listening environment
Specify speaker acoustic parameters automatically
(Yamaha Parametric Room Acoustic Optimizer - YPAO).......................................................................37
Set up this unit’s speaker configuration simply <Power Amp Assign> ..................................................91
Specify settings for each speaker <Configuration>.................................................................................91
Control volume control for each speaker <Level> ..................................................................................93
Apply speaker distance settings <Distance> ...........................................................................................93
Control equalizer sound quality <Parametric EQ>..................................................................................93
Adjust test tone speaker <Test Tone> ......................................................................................................94
Adjust audio signals output from this unit
Correct lag between audio and video signals <Lipsync> ........................................................................94
Select a dynamic range adjustment method <Dynamic Range> .............................................................95
Specify the maximum volume <Max Volume>.......................................................................................95
Specify the initial volume <Initial Volume>............................................................................................95
Restrict the video signals during the Pure Direct Mode <Pure Direct Mode>........................................95
Adjust DSP effect and volume level <Adaptive DSP Level>..................................................................95
Adjust video signals output from this unit
Convert analog video signal to another type of signal <Analog to Analog Conversion> .......................96
Specify the resolution and aspect ratio of output video signals <Processing>........................................96
HDMI settings
Assign the audio input source for the TV <TV Audio Input>.................................................................98
Listen to TV audio with HDMI cable connection <ARC (Audio Return Channel)>..............................97
Transmit HDMI audio/video to the TV during standby mode <Standby Through>...............................98
Change the output destination of HDMI input audio signals <Audio Output>.......................................98
Network settings
Set the IP address of this unit <IP Address> ...........................................................................................99
Accept the commands via LAN network when this unit is in the standby mode
<Network Standby>.................................................................................................................................99
Set the mac address filter for this unit <MAC Address Filter> ...............................................................99
Enable listening in multiple rooms (multi-zone function)
Adjust Zone2 volume <Zone2 Set>.......................................................................................................100
Display the Zone2 menu on the TV <Monitor Out Assign>.................................................................100
Rename each zone or scene <Zone2 Scene Rename/Zone Rename> ...................................................101
Specify other functions for this unit
Enter standby mode automatically when no operations are performed <Auto Power Down> .............102
Assign the other input to the selected input source <Input Assignment> .............................................102
Adjust the brightness of the front panel display <Dimmer> .................................................................103
Change the wall paper displayed on the TV screen <Wall Paper>........................................................103
Specify the function of the TRIGGER OUT jack for controlling external components
<Trigger Output1/Trigger Output2>......................................................................................................103
Prohibit changes to settings <Memory Guard>.....................................................................................104
Adjust settings for each input source <Option menu>
Adjust bass and treble levels <Tone Control>.........................................................................................56
Enable low-volume background music <Adaptive DRC> ......................................................................56
Enjoying more spatial sound fields <CINEMA DSP 3D Mode>............................................................56
Adjust the vertical position of dialogues <Dialogue Lift>......................................................................56
Select the 5.1-channel signal playback method <Extended Surround> ..................................................56
Adjust the volume of input sources <Volume Trim>...............................................................................57
Selecting audio input jacks <Audio Select>............................................................................................57
Shuffle or repeat the song <Shuffle/Repeat>...........................................................................................57
Connect / Disconnect Bluetooth component to this unit <Connect/Disconnect> ...................................57
Pairing Bluetooth component with this unit <Pairing>...........................................................................57
INTRODUCTION
En 8
Front panel
a MAIN ZONE A (Power)
Switches this unit between on and standby mode.
b HDMI Through/iPod Charge indicator
Lights up in any of the following cases while the unit is in standby
mode.
When the Standby Through function is enabled and audio/video
from an external component connected with HDMI is output to a TV
during standby mode (
p. 98).
When an iPod/iPhone, which is placed in the Universal Dock for
iPod, is charging while the unit is in standby mode (
p. 80).
This indicator also lights up when the Yamaha Wireless System for
iPod is connected to this unit (
p. 72).
c Front panel display
Displays information on this unit (
p. 11).
d PURE DIRECT
Switches this unit to Pure Direct Mode (
p. 49).
e INPUT selector
Selects an input source from which to playback. Rotate this selector to
cycle through the input sources in order.
f VOLUME
Adjusts the volume level.
Part names and functions
Opening and closing the front panel door
To use controls or jacks behind the front panel door, gently press
the bottom of the door to open it. Keep the door closed when not
using controls or jacks behind the front panel door.
Continues to the
next page
a
e f
c db
En 9
INTRODUCTION
Part names and functions
Front panel with the cover opened
g ON SCREEN
Turns on and off the ON SCREEN menu.
h OPTION
Turns on and off the Option menu (
p. 54).
i TONE/BALANCE
Adjusts high-frequency/low-frequency output of speakers/headphones
in each zone (
p. 45, p. 120).
Adjusts the balance of the volume of the left and right channels in
Zone2 (
p. 120).
j STRAIGHT
Changes a sound program to straight decoding mode (
p. 48).
k PROGRAM l / h
Selects a sound program (
p. 47). Press the left or right key
repeatedly to cycle through sound programs.
l SCENE
Switches the input source, the sound program, and the HDMI OUT
with a single button (
p. 46, p. 81). When this unit is in standby
mode, press this key to switch on.
m MULTI ZONE
ZONE2
Switches to enable/disable the audio and video output to Zone2
(
p. 100, p. 118).
ZONE CONTROLS
Switches to Zone2 operation mode. This unit, or its remote control,
can be used to select input sources or adjust volume for an external
amplifier in another room or the built-in amplifier for speakers in
another room (
p. 120).
n INFO
Changes the information displayed on the front panel display
(
p. 11).
o MEMORY
Registers FM/AM stations as preset stations (
p. 60). J1
p FM/AM
Sets the FM/AM tuner band to FM or AM (
p. 59). J1
q PRESET j / i
Selects an FM/AM preset station (
p. 60). J1
r Cursor B / C / D / E, ENTER, RETURN
s USB port
For connecting a USB memory device or USB portable audio player
(
p. 35).
t DISPLAY
Switches the display between the Now Playing view and the Browse view.
u YPAO MIC jack
Connect the supplied YPAO microphone and adjust the speaker
balance automatically (
p. 37).
v PHONES jack
For plugging headphones in. Sound effects applied during playback
can also be heard through the headphones.
w VIDEO AUX jacks
For connecting game consoles to this unit temporarily (
p. 32).
x TUNING/CH jj / ii
Changes FM/AM tuner frequencies (
p. 59). J1
Cursor B / C / D / E Select menu items and change settings when
menus, etc., are displayed.
ENTER Confirms a selected item.
RETURN Returns to the previous screen when menus are
displayed, or close the menu.
n
r
xt w
k
mg li onjh p
vus
q
J
1 : Usable when you have selected TUNER input.
En 10
INTRODUCTION
Part names and functions
Rear panel
a PHONO jacks
For connecting a turntable (
p. 31).
b DOCK jack
For connecting an optional Universal Dock for iPod (such as YDS-
12), Wireless System for iPod (YID-W10), or Bluetooth Wireless
Audio Receiver (YBA-10) (
p. 70, p. 72, p. 74).
c NETWORK port
For connecting to the network (
p. 34).
d HDMI OUT 1-2 jacks
For connecting an HDMI - compatible TV to output audio/video
signals (
p. 25).
e MON.OUT/ZONE OUT jacks (S-VIDEO/VIDEO jacks)
For connecting a TV capable of receiving video input, and outputting
video signals to it (
p. 25, p. 26).
f COMPONENT VIDEO jacks
For connecting external components equipped component video-
compatible outputs to receive video signals (
p. 28).
g HDMI input jacks
For connecting external components equipped with HDMI-
compatible outputs to receive audio/video signals (
p. 27).
h MONITOR OUT/ZONE OUT jacks (COMPONENT VIDEO
jacks)
For connecting TV that are compatible with component video signals,
using three cables to output video signal (
p. 25).
i REMOTE IN/OUT jacks
For connecting an external component that supports the remote
control function (
p. 33).
j TRIGGER OUT 1-2 jack
For connecting an external component that supports the trigger
function to operate it linked with operation of this unit (
p. 33).
k RS-232C terminal
This is a control expansion terminal for custom installation. Consult
your dealer for details.
l VOLTAGE SELECTOR
(General model only)
Select the switch position according to your local voltage (Refer to
Quick Reference Guide).
m AV1-4 jacks
For connecting to external components equipped with audio/video
outputs to receive audio/video signals (
p. 28).
n ANTENNA jacks
For connecting AM and FM antennas (
p. 36).
o AV OUT jacks
For outputting audio/video signals received when analog inputs are
selected (
p. 34).
p AUDIO1-4 jacks
For connecting external components equipped with audio outputs to
receive audio signals (
p. 31).
q MULTI CH INPUT jacks
For connecting a player that supports a multi-channel output
(
p. 32).
r ZONE OUT jacks
Outputs sound of this unit to an external amplifier set in a different
room. (
p. 118).
s PRE OUT terminals
For connecting a subwoofer with built-in amplifier or an external
power amplifier (
p. 21, p. 22).
t SPEAKERS terminals
For connecting the front, center, surround and surround back speakers
(
p. 19). Connect the presence speakers (p. 19) or the speakers for
Zone2 (
p. 18) to the EXTRA SP jacks.
u AC IN
For connecting the supplied power cable.
HDMI OUT
12
ZONE OUT PRE OUT
ZONE 2
AV OU T
YP
B
P
R
SURROUND
SUR. BACK
CENTER
SUBWOOFER
1
2
MON.OUT/ZONE OUT
ARC ARC
SELECTABLE
FRONT
(SINGLE)
SU
RR
OU
ND
SU
RR
OU
ND BA
C
K
/
S
PEAKER
S
C
ENTE
R
AV 1
AV 2
AV
3
AV 4
HDMI
AV
5
AV
6
AV 7
S
IN
G
L
E
FR
O
BI
-
AMP
4
AV
3
A
V 4
T
ICAL
O
PTICA
L
AU
DI
O
1
(
2 TV
)
(3 CD)
A
U
DI
O
2 A
U
DI
O
3
AU
DI
O
4
FRON
T
SURROUND
SUR. BAC
K
S
UBWOOFE
R
C
ENTER
M
U
LTI
C
H INP
UT
CO
MP
O
NENT VIDE
O
C
OAXIA
L
Y
P
B
P
R
Y
P
B
P
R
C
D
(
1 BD/DVD
)
AV 1
A
V 2
B
A
Ԝ
ԝ
IN
OUT
R
EM
O
TE
Distinguishing the input and output jacks
The area around the audio/video output jacks is marked
in white to prevent connection errors. Use these jacks to
output audio/video signals to a TV or other external
component.
Output jacks
AC IN
SURROUND SURROUND BACK/
SPEAKERS
CENTER
AV 1
HDMI OUT
AV 2 AV 3 AV 4
HDMI
AV 5 AV 6 AV 7
SINGLE
FRONT
BI-AMP
12
PHONO
GND
(1 BD/DVD)
AV 1
DOCK NETWORK
AV 2 AV 3 AV 4
AV 3
AV 4
COAXIAL COAXIAL
OPTICAL OPTICAL
OPTICAL
AUDIO 1
(2 TV)
(3 CD)
AUDIO 2 AUDIO 3 AUDIO 4
FRONT
SURROUND
SUR. BACK
SUBWOOFER
CENTER
MULTI CH INPUT
COMPONENT VIDEO
COAXIAL
MONITOR OUT/ZONE OUT
ZONE OUT PRE OUT
ZONE 2
AV OUT
YP
B
P
R
YP
B
P
R
YP
B
P
R
C
D
SURROUND
SUR. BACK
CENTER
SUBWOOFER
1
2
RS-232C
2
1
TRIGGER
OUT
+12V 0.1A MAX.
MON.OUT/ZONE OUT
ARC ARC
SELECTABLE
FRONT
(1 BD/DVD)
AV 1
AV 2
B
A
ԘԙԚԛ Ԝԝ
(SINGLE)
ZONE2/
F.PRESENCE
EXTRA SP
ANTENNA
75
GND
AM
(4 RADIO)
IN
OUT
REMOTE
bad g kjf
tm onu
c
e h i
p q r s
l
En 11
INTRODUCTION
Part names and functions
Front panel display
a Tuner indicator
Light up according to the status of a received station (
p. 59).
b ZONE2 indicator
Lights up when the audio and video output to Zone2 is enabled
(
p. 120).
c SLEEP indicator
Blinks when the sleep timer is on (
p. 12, p. 120).
d PARTY indicator
Lights up when the party mode is active (
p. 100).
e Multi information display
Displays a range of information on menu items and settings.
f VOLUME indicator
Displays the current volume level.
g HDMI indicator
Lights up during normal HDMI communication.
IN indicator
Lights up when this unit detects the external component connected to
the HDMI input jack (
p. 27).
OUT 1/OUT 2 indicators
Indicate which HDMI OUT jack outputs audio/video signals
(
p. 25).
h ENHANCER indicator
Lights up when the Compressed Music Enhancer is active (
p. 49).
i CINEMA DSP indicator
Lights up when a sound field effect that uses CINEMA DSP
technology is selected.
j CINEMA DSP 3D indicator
Lights up when CINEMA DSP 3D is activated (
p. 48).
k Cursor indicators
Light up if corresponding cursors on the remote control are available
for operations.
l MUTE indicator
Blinks when audio is muted.
m Speaker indicators
Indicate speaker terminals from which signals are output.
n ADAPTIVE DRC indicator
Lights up when the adaptive dynamic range control feature is tuned on
(
p. 56).
Surround speaker L
Subwoofer 1
Surround speaker R
Center speaker
Surround back
speaker L
Surround back
speaker R
Surround back
speaker J1
Presence speaker L Presence speaker
R
Front speaker L Front speaker R
Subwoofer 2
Switching information on the front panel display
The front panel can display sound programs and surround
decoder names as well as the active input source.
Press fINFO repeatedly to cycle through displayed
informations. J2
VOLUME
AV1

Standard
Input source name
Sound program (DSP program)
STEREO
TUNED
PARTY
ENHANCER
SLEEP
MUTE
VOLUME
ADAPTIVE
DRC
a be fc
ihj mknlgk
d
J
1 : “SB” is displayed when using a 6.1-channel configuration only.
J
2 : During FM/AM reception, the frequency is displayed instead of the input source.
En 12
INTRODUCTION
Part names and functions
Remote control
a Remote control signal transmitter
Transmits infrared signals.
b MAIN/ZONE2
Switches the zone to be operated by the remote control between the
Main zone and Zone2 (
p. 120).
c SOURCE A (SOURCE Power)
Switches an external component on and off.
d Input selector
Select an input source on this unit from which to playback.
e Radio control keys
Operates the FM/AM tuner. These keys are used when using the tuner
input.
f INFO
Cycles the information displayed on the front panel display (the name
of the currently selected input source, the sound program, the
surround decoder, the FM/AM tuner frequency, etc.).
g SLEEP
Switches this unit to standby mode automatically after a specified
period of time has elapsed (sleep timer). Press this key repeatedly to
set the time for the sleep timer function.
The SLEEP indicator lights up when the sleep timer is on.
h PARTY
Switches the party mode on and off (
p. 120).
i SCENE
Switch the input source and the sound program with a single button
(
p. 46). When this unit is in standby mode, press this key to switch on.
j ON SCREEN
Turns on and off the ON SCREEN menu.
SCENE
VOLUME
ENHANCER
SUR. DECODE
STRAIGHTSLEEP PURE DIRECT
AV
AUDIO
1234
75
FM
INFO
MEMORY
AM
PRESET
PARTY
MOVIE MUSIC
MUTE
ENTER
7856
90
10
1234
REC
ENT
TV
TV VOL TV CH
TOP
MENU
POP-UP
MENU
SOURCE
MAIN
ZONE 2
RECEIVER
CODE SET
INPUT
MUTE
DOCK
HDMI OUT
MULTI
1234
6
V-AUX
USB
NET
TUNER
PHONO
TUNING
ON SCREEN OPTION
1
2
3
4
BD/DVD
TV
CD
RADIO
1
2
3
4
BD/DVD
TV
CD
RADIO
RETURN
DISPLAY
a
c
b
e
i
j
f
g
h
d
AV1-7 AV1-7 jacks
V-AUX Front panel VIDEO AUX jacks
AUDIO1-4 AUDIO1-4 jacks
USB A USB storage device connected to the USB port.
NET Internet radio, a USB connected to the USB port,
or a PC connected to the NETWORK port.
MULTI MULTI CH INPUT jacks
DOCK A Universal Dock for iPod, Wireless System for
iPod, or Bluetooth Wireless Audio Receiver
connected to the DOCK jack.
TUNER FM/AM tuner
PHONO PHONO jacks
FM Sets the FM/AM tuner band to FM.
AM Sets the FM/AM tuner band to AM.
MEMORY Presets radio stations.
PRESET F / G Selects a preset stations when the FM/AM.
TUNING H / I Changes tuning frequencies.
120min. 90min.
60min.30min.Off
Installing batteries in the remote control
When inserting batteries in the remote control, remove the
battery compartment cover from the reverse side of the remote
control, and insert four AAA batteries into the battery
compartment so that they match with the polarity markings (+
and -).
Replace the batteries with new ones if the remote control can
only be operated within a narrow range.
NOTE
If there are remote control codes for external components
registered to the remote control, removing the batteries for more
than 2 minutes, or leaving exhausted batteries in the remote
control, may clear the remote control codes. If this should occur,
replace the batteries with new ones, and set the remote control
codes.
a
c
b
Battery compartment
cover
Battery compartment
Continues to the
next page
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146

Yamaha RX-V1067 Инструкция по применению

Категория
Аудио-видео ресиверы
Тип
Инструкция по применению

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ

на других языках