Yamaha N3X Инструкция по применению

FRANÇAIS

ESPAÑOL

Owner’s Manual

Mode d'emploi

Manual de instrucciones

IMPORTANT – Check your power supply –

Make sure that your local AC mains voltage matches the voltage

specified on the name plate on the bottom panel. In some areas

a voltage selector may be provided on the bottom of the main

keyboard unit near the power cord. Make sure that the voltage

selector is set for the voltage in your area. The voltage selector

is set at 240V when the unit is initially shipped. To change the

setting use a “minus” screwdriver to rotate the selector dial so

that the correct voltage appears next to the pointer on the panel.

Before using this instrument, be sure to read “PRECAUTIONS”

on pages 5–6.

When assembling the unit, consult a qualified AvantGrand

dealer. (Refer to the assembly instructions at the end of this

manual.)

IMPORTANT – Vérifiez votre source d'alimentation –

Vérifiez que la tension de l'alimentation secteur correspond à

celle spécifiée sur la plaque du fabricant, située sur le panneau

inférieur. Les instruments vendus dans certaines régions

disposent d'un sélecteur de tension sur la partie inférieure du

clavier de l'unité principale, à côté du cordon d'alimentation.

Assurez-vous que le sélecteur de tension est réglé sur la tension

utilisée dans votre région. À sa sortie d'usine, le sélecteur est

réglé sur 240 V. Pour modifier ce réglage, utilisez un tournevis

plat et faites tourner le cadran du sélecteur jusqu'à ce que la

valeur correcte apparaisse à côté de l'indicateur sur le panneau.

Avant d'utiliser cet instrument, lisez attentivement la section

« PRÉCAUTIONS D'USAGE » aux pages 5-6.

Lors du montage de l'unité, contactez un revendeur AvantGrand

agréé. (Reportez-vous aux instructions de montage figurant à la

fin de ce manuel.)

IMPORTANTE – Compruebe la fuente de alimentación –

Asegúrese de que la tensión de la red eléctrica local de CA

coincide con la tensión especificada en la placa situada en el

panel inferior. Es posible que en algunas zonas se suministre un

selector de tensión en la parte inferior de la unidad del teclado

principal, junto al cable de alimentación. Asegúrese de que este

selector está ajustado según la tensión de la zona. El selector

de tensión viene ajustado de fábrica para 240 V. Para cambiar

el ajuste, utilice un destornillador de punta normal para girar el

selector hasta que la tensión correcta aparezca al lado del

puntero del panel.

Antes de utilizar el instrumento, lea la sección

“PRECAUCIONES”, en las páginas 5-6.

Al montar la unidad, consulte con un concesionario cualificado

de Avant Grand (consulte las instrucciones de montaje al final

de este manual).

ENGLISH

N3X

2•N3X

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these graph-

ics appears on this page. Please observe all cautions indi-

cated on this page and those indicated in the safety

instruction section.

See bottom of Keyboard enclosure for graphic symbol

markings.

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important operat-

ing and maintenance (servicing) instruc-

tions in the literature accompanying the

product.

The lightning flash with arrowhead

symbol, within the equilateral triangle,

is intended to alert the user to the pres-

ence of uninsulated “dangerous volt-

age” within the product’s enclosure that

may be of sufficient magnitude to con-

stitute a risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic products

are tested and approved by an independent safety testing

laboratory in order that you may be sure that when it is

properly installed and used in its normal and customary

manner, all foreseeable risks have been eliminated. DO

NOT modify this unit or commission others to do so unless

specifically authorized by Yamaha. Product performance

and/or safety standards may be diminished. Claims filed

under the expressed warranty may be denied if the unit is/

has been modified. Implied warranties may also be

affected.

SPECIFICATIONS SUBJECT TO CHANGE: The

information contained in this manual is believed to be cor-

rect at the time of printing. However, Yamaha reserves the

right to change or modify any of the specifications without

notice or obligation to update existing units.

ENVIRONMENTAL ISSUES: Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargeable battery which (if applicable) is soldered in

place. The average life span of this type of battery is

approximately five years. When replacement becomes nec-

essary, contact a qualified service representative to per-

form the replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away from

children. Dispose of used batteries promptly and as regu-

lated by applicable laws. Note: In some areas, the servicer

is required by law to return the defective parts. However,

you do have the option of having the servicer dispose of

these parts for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and fed-

eral regulations that relate to the disposal of products that

contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the manu-

facturer’s warranty, and are therefore the owners responsi-

bility. Please study this manual carefully and consult your

dealer before requesting service.

NAME PLATE LOCATION: The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number,

and the date of purchase in the spaces provided below and

retain this manual as a permanent record of your purchase.

Model

Serial No.

Purchase Date

SPECIAL MESSAGE SECTION

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

92-469-q (bottom)

N3X •3

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifica-

tions not expressly approved by Yamaha may void your author-

ity, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class

“B” digital devices. Compliance with these requirements pro-

vides a reasonable level of assurance that your use of this

product in a residential environment will not result in harmful

interference with other electronic devices. This equipment gen-

erates/uses radio frequencies and, if not installed and used

according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic

devices. Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If this product

is found to be the source of interference, which can be deter-

mined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected

by the interference.

Utilize power outlets that are on different branch (circuit breaker

or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distribute

this type of product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of America, Elec-

tronic Service Division, 6600 Orangethorpe Ave, Buena Park,

CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Hybrid Piano

Model Name : N3X

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference

that may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

* This applies only to products distributed by YAMAHA

CORPORATION OF AMERICA.

(FCC DoC)

4•N3X Owner’s Manual

The above warning is located on the bottom of the unit.

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and main-

tenance (servicing) instructions in the liter-

ature accompanying the product.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accor-

dance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tri-

pod, bracket, or table specified by

the manufacturer, or sold with the

apparatus. When a cart is used,

use caution when moving the

cart/apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualified service personnel. Ser-

vicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has

been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT SAFETY INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

N3X Owner’s Manual •5

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the

following:

• Do not place the power cord near heat sources such as heaters or radiators. Also,

do not excessively bend or otherwise damage the cord, or place heavy objects on

it.

• Only use the voltage specified as correct for the instrument. The required voltage

is printed on the name plate of the instrument.

• Use only the supplied power cord/plug.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the instrument

or attempt to disassemble or modify the internal components in any way. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place on it any containers (such as vases, bottles or glasses)

containing liquids which might spill into any openings. If any liquid such as water

seeps into the instrument, turn off the power immediately and unplug the power

cord from the AC outlet. Then have the instrument inspected by qualified Yamaha

service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may fall

over and cause a fire.

• When one of the following problems occur, immediately turn off the power switch

and disconnect the electric plug from the outlet. Then have the device inspected

by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• When removing the electric plug from the instrument or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used for

extended periods of time, or during electrical storms.

• Read carefully the attached documentation explaining the assembly process.

Failure to assemble the instrument in the proper sequence might result in damage

to the instrument or even injury.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

• Since this product is very heavy, make sure that a sufficient number of people are

on hand to help, so you can lift and move it safely and easily. Attempting to lift or

move the instrument by force may damage your back, result in other injury, or

cause damage to the instrument itself.

• Before moving the instrument, remove all connected cables, to prevent damage to

the cables or injury to anyone who might trip over them.

• When setting up the product, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the power

switch and disconnect the plug from the outlet. Even when the power switch is

turned off, electricity is still flowing to the product at the minimum level. When

you are not using the product for a long time, make sure to unplug the power cord

from the wall AC outlet.

Power supply/Power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/Power cord

Assembly

Location

DMI-5 1/2

6•N3X Owner’s Manual

• Though the wooden parts of this instrument have been designed and produced

with care concerning the environment and human health, in some rare instances

customers may sense an unusual odor or develop irritation in the eyes, due to the

coating material and adhesive.

To avoid this, we recommend that you observe the following:

1. Specially ventilate the room for several days after unpacking and installing this

instrument, since it has been packed in airtight conditions in order to maintain

quality during transportation.

2. If the room housing the instrument is small, continue to ventilate it normally,

either daily or periodically.

3. If you have left the instrument in a closed room for a long time under high

temperature, ventilate the room, then lower the temperature if possible, before

using the instrument.

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all components,

set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum levels and

gradually raise the volume controls while playing the instrument to set the desired

listening level.

• Do not insert a finger or hand in any gaps on the fallboard or instrument. Also

take care that the fallboard does not pinch your finger.

• Do not apply excessive force when closing the fallboard.

A fallboard equipped with the SOFT-CLOSE™ mechanism closes the cover

slowly. Applying excessive force to the fallboard when closing it could damage

the SOFT-CLOSE™ mechanism, and possibly result in injury to your hands and

fingers caught under the closing fallboard.

• Never insert or drop paper, metallic, or other objects into the gaps on the

fallboard, panel or keyboard. This could cause physical injury to you or others,

damage to the instrument or other property, or operational failure.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a

high or uncomfortable volume level, since this can cause permanent hearing loss.

If you experience any hearing loss or ringing in the ears, consult a physician.

• Do not place the bench in an unstable position where it might accidentally fall

over.

• Do not play carelessly with or stand on the bench. Using it as a tool or stepladder

or for any other purpose might result in accident or injury.

• Only one person should sit on the bench at a time, in order to prevent the

possibility of accident or injury.

• For benches that can be adjusted, do not adjust the bench height while sitting on

the bench, since this can cause excessive force to be imposed on the adjustment

mechanism, possibly resulting in damage to the mechanism or even injury.

• If the bench screws become loose due to extensive long-term use, tighten them

periodically using the specified tool in order to prevent the possibility of accident

or injury.

• Keep special watch over any small children so that they don’t fall off the rear of the

bench. Since the bench does not have a backrest, unsupervised use may result in

accident or injury.

Always turn the power off when the instrument is not in use.

NOTICE

To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.

 Handling

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio

may generate noise. When you use the instrument along with an application on your iPad, iPhone or iPod touch, we recommend that you set “Airplane

Mode” to “ON” on that device in order to avoid noise caused by communication.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day)

to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation. (Verified operating temperature range: 5° –

40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.

• Bumping the surface of the instrument with metal, porcelain, or other hard objects can cause the finish to crack or peel. Use caution.

 Maintenance

• When cleaning the instrument, use a soft and dry/slightly damp cloth. Do not use paint thinners, solvents, alcohol, cleaning fluids, or chemical-

impregnated wiping cloths.

• Gently remove dust and dirt with a soft cloth. Do not wipe too hard since small particles of dirt can scratch the instrument's finish.

• During extreme changes in temperature or humidity, condensation may occur and water may collect on the surface of the instrument. If water is left, the

wooden parts may absorb the water and be damaged. Make sure to wipe any water off immediately with a soft cloth.

 Saving data

• Some of the data of this instrument (page 40) are retained when the power is turned off. However, the saved data may be lost due to some failure, an

operation mistake, etc.

• The Song data saved to the internal memory of this instrument (page 34) are retained when the power is turned off. However, the saved data may be lost

due to some failure, an operation mistake, etc. Save your important data onto USB flash drive/an external device such as a computer (pages 38, 43).

Before using a USB flash drive, make sure to refer to page 36.

• To protect against data loss through USB flash drive damage, we recommend that you save your important data onto spare USB flash drive or an external

device such as a computer as backup data.

Connections

Handling caution

Using the bench (If included)

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

DMI-5 2/2

N3X Owner’s Manual •7

Information

 About copyrights

• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal

use.

• This product incorporates and bundles contents in which Yamaha owns copyrights or with respect to which Yamaha has license to use others' copyrights.

Due to copyright laws and other relevant laws, you are NOT allowed to distribute media in which these contents are saved or recorded and remain virtually

the same or very similar to those in the product.

* The contents described above include a computer program, Accompaniment Style data, MIDI data, WAVE data, voice recording data, a score, score

data, etc.

* You are allowed to distribute medium in which your performance or music production using these contents is recorded, and the permission of Yamaha

Corporation is not required in such cases.

 About functions/data bundled with the instrument

• Some of the preset songs have been edited for length or arrangement, and may not be exactly the same as the original.

 About this manual

• The illustrations and displays as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your

instrument.

• iPad, iPhone or iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

 Tuning

• Unlike an acoustic piano, this instrument does not need to be tuned by an expert (although the pitch can be user-adjusted to match other instruments).

This is because the pitch of digital instruments is always maintained perfectly. However, if you feel there is something abnormal concerning the keyboard

touch, contact your Yamaha dealer.

Transporting / Placing

If you move to another location, transport the instrument

horizontally. Do not lean it up against a wall or stand it up

side down. Do not subject the instrument to excessive

vibration or shock.

CAUTION

When moving the instrument, always hold the bottom of the

main unit.

Be sure not to hold the control panel located on the bottom left.

Improper handling can result in damage to the instrument or

personal injury.

To enhance the safety and to protect the floor, we recommend

to put the instrument on caster cups (for a grand piano).

Do not hold here.

Hold here.

Do not hold the control panel.

The model number, serial number, power requirements, etc., may be found

on or near the name plate, which is at the bottom of the unit. You should

note this serial number in the space provided below and retain this manual

as a permanent record of your purchase to aid identification in the event of

theft.

Model No.

Serial No.

(bottom_en_01)

The name plate is located

on the bottom of the unit.

8•N3X Owner’s Manual

Hybrid Piano

N3X

Combining over a century’s experience in crafting world-class pianos with the latest in advanced

technologies, Yamaha proudly introduces an instrument that is closer than ever to an actual

acoustic grand piano—equipped with every essential element pianists demand.

Authentic acoustic piano touch with special grand piano action and piano keyboard

An actual acoustic grand piano has an unmistakable rich expressive quality, thanks to its finely nuanced touch and

exceptional response. The remarkable AvantGrand N3X is the culmination of our many decades of expertise in

crafting grand pianos, and offers the discerning player a specially-developed grand piano action featuring a

configuration identical to the action of a real grand. The wood construction of the keyboard mirrors that of a grand

piano, and features the material ”Ivorite” for the white keys, giving them a texture amazingly close to that of natural

ivory. The result is a wonderfully expressive keyboard that provides an authentic touch and feel. In addition to a

hammer sensor, this instrument employs a non-contact key sensor that has no effect on the movement of the keys, yet

accurately recognizes the player's pressure on the keyboard, timing, and the other delicate nuances that affect musical

expression. Moreover, the TRS (Tactile Response System;

page 25) realistically reproduces the resonance of the

instrument, or the physical vibration that you feel from the keys or the pedals when you play a real grand piano.

Unique acoustic-sampling technique and speaker system

One of the most important factors in the resonance of an actual grand piano is the soundboard. Aiming to effectively

recreate that resonance, we sampled the grand piano voices utilizing Spatial Acoustic Sampling, which samples at

not only the left and right, but also center and rear positions. In addition, the installed speakers mimic the positions in

the grand piano from which the original samples were taken, and each of the speakers is equipped with its own

dedicated amplifier. This Spatial Acoustic Speaker System ensures optimum sound at the player's position, providing

more natural expression in the delicate nuances of each note. Moreover, a Soundboard Resonator, installed where the

music rest would be when laid flat, enhances the expressive response of the sound, providing a realistic response—

especially in the high notes.

The sound of several famous grand pianos in a single instrument  Page 20

The AvantGrand N3X puts the sounds of several different renowned grand pianos at your fingertips, including the

CFX, Yamaha’s flagship concert grand piano, a Bösendorfer* Imperial, an instrument esteemed by pianists

throughout its long history, and more—each with its own distinctive appeal and sonic characteristics. Simply select

the particular piano sound desired, according to the music you intend to play or your personal preferences.

* Bösendorfer is a subsidiary company of Yamaha.

Natural sound distance sensation for headphone play  Page 18

This instrument features a binaural sampling sound designed especially for use with headphones. Binaural sampling

is a method which uses two microphones placed where the ears of a performer would be, and records that piano

sound as it is. Listening to the sound created through this method with headphones gives the impression of being

immersed in the sound, as if it was actually emanating from the piano.

N3X Owner’s Manual •9

Table of Contents

About Manuals

This instrument has the following documents and instructional materials.

 Included Documents

Owner’s Manual (this book)

This manual describes how to use this instrument.

 Online Materials (from Yamaha Downloads)

iPhone/iPad Connection Manual (only in English,

French, German and Spanish)

Explains how to connect the instrument to smart

devices, such as an iPhone, iPad, etc.

Computer-related Operations

Includes instructions on connecting this instrument to a

computer, and operations related to transferring files

and MIDI data.

MIDI Reference

Contains MIDI related information such as MIDI Data

Format and the MIDI Implementation Chart.

MIDI Basics (only in English, French, German and

Spanish)

Contains basic explanations about MIDI.

To obtain these manuals, access the Yamaha Downloads, enter the

model name for searching the desired files.

Included Accessories

Owner’s Manual (this book)

Online Member Product Registration

The “PRODUCT ID” on the sheet will be needed when you fill out the

User Registration form.

Warranty*

Felt key cover

Power cord

Bench*

* May not be included depending on your area. Check with your Yamaha

dealer.

Yamaha Downloads http://download.yamaha.com/

PRECAUTIONS ....................................................... 5

Setting Up

Panel Controls and Terminals .................................. 10

Playing the Keyboard ................................................ 12

Opening/Closing the Fallboard....................................12

Using the Music Rest...................................................12

Opening/Closing the Lid ..............................................13

Power Supply ..............................................................14

Turning the Power On/Off............................................15

Adjusting the Master Volume.......................................17

Using Headphones......................................................18

Using the Pedals .........................................................19

Main Operations

Basic Operations and More ...................................... 20

Selecting a Voice.........................................................20

Listening to the Voice Demo Songs ............................21

Using the Metronome ..................................................22

Adjusting the Tempo....................................................23

Changing the Touch Sensitivity ...................................24

Adjusting the Strength of Vibration (TRS) ...................25

Playing the Realistic Resonance-enhanced VRM

Voices..........................................................................26

Enhancing the Sound with Reverb ..............................27

Adjusting the Brightness of the Sound (Brilliance) ......27

Transposing the Pitch in Semitones ............................28

Fine-tuning the Pitch....................................................29

Setting the Scale Tuning .............................................30

Playing Back Songs...................................................31

Songs compatible with this instrument........................ 31

Playing back Songs .................................................... 32

Recording Your Performance ...................................34

Using USB Flash Drives ............................................ 36

About USB Flash Drives ............................................. 36

Formatting USB Flash Drive ....................................... 37

Copying User Songs in the Instrument to USB Flash Drive

.38

Deleting a Song file..................................................... 39

Managing files on a USB flash drive ........................... 39

Backup Data and Initializing ..................................... 40

Backup Data in Internal Memory................................. 40

Initializing the Backup Data......................................... 40

Connections ............................................................... 41

Connecting Audio Devices ([AUX IN] jack, AUX OUT

[L/L+R] [R] jacks) ........................................................ 41

Connecting to a Mixer—OUTPUT [L] [R] jacks

(Balanced)................................................................... 42

Connecting to a Computer ([USB TO HOST] terminal)

... 43

Connecting to an iPhone/iPad (MIDI [IN] [OUT]

connectors, [USB TO HOST] terminal) ....................... 43

Connecting External MIDI Devices (MIDI [IN] [OUT]

connectors) ................................................................. 44

Appendix

Message List .............................................................. 46

Troubleshooting......................................................... 47

Preset Song List......................................................... 48

Assembling the Unit .................................................. 49

Specifications.............................................................52

Index............................................................................ 53

Quick Operation Guide* ............................................54

* This is a quick reference for operation of the functions assigned to the buttons

and keyboard.

Getting started playing your new Avant Grand!

This section explains how to make detailed settings for the

instrument’s various functions.

This section includes a list of display messages, Quick

Operation Guide and other information.

10 • N3X Owner’s Manual

Panel Controls and Terminals

Overview

The jacks and terminals on the underside of the instrument as shown here may seem to be in reverse from your per-

spective in front of the instrument. Make sure when using these to carefully check the names as printed on the panel

before making connections.

Jacks and Terminals

q [PHONES] jacks .................................. page 18

w [AUX IN] jack........................................ page 41

e [USB TO DEVICE] terminal ................. page 36

r [USB TO HOST] terminal .....................page 43

t MIDI [IN] [OUT] connectors..........pages 43, 44

y AUX OUT [L/L+R] [R] jacks .................page 42

u OUTPUT [L] [R] jacks ..........................page 42

Stay

(page 13)

Jacks and Terminals

(See below.)

Lid

(page 13)

Music rest

(page 12)

Fallboard

(page 12)

Pedals

(page 19)

[AC IN]

connector

(page 14)

Power switch

(page 15)

Underneath

the instrument

Right

(toward higher

keys)

Towa rd

rear leg

Left

(toward lower

keys)

Underneath

the instrument

Underneath

the instrument

Control panel

(page 11)

Jacks and Terminals

(See below.)

NOTE

Do not place any objects on the soundboard

(area shaded in gray in the illustration above).

Doing so may adversely affect the sound.

Soundboard

qwe

ty ur

Setting Up

Panel Controls and Terminals

N3X Owner’s Manual •11

Control Panel

i [MASTER VOLUME] control ................ page 17

o Display.............................................See below.

!0 [RECORD] button ................................ page 35

!1 [PLAY/STOP] button..................... pages 32, 35

!2 [+]/[-] button

!3 [DEMO/SONG] button ........... pages 21, 32, 34

!4 [PIANO/VOICE] button ........................ page 20

!5 [TRS] button......................................... page 25

!6 [REVERB] button ................................. page 27

!7 [METRONOME] button ................ pages 22, 23

!8 [FUNCTION] button ..........pages 16, 27, 28, 29

!0 !1 !2 !3 !4 !5 !6 !7 !8

NOTICE

Do not pull on the [MASTER VOLUME] control to

slide out the control panel.

The control panel is located at

the bottom left of the instrument.

Slide the panel out to use it.

Display

Indicates various values such as Song number and Parameter value. Note that the display turns dark and cannot

be seen after the value is set.

This display also indicates various three-character messages. For details, refer to page 46.

d.01

Song number Parameter value

12 • N3X Owner’s Manual

Playing the Keyboard

To open the fallboard, hold the hand grip with both hands, then lift the fallboard slightly, and push it up

and back. To close the fallboard, lower the fallboard back in place gently with both hands.

The fallboard is equipped with the special SOFT-CLOSE™ mechanism which closes the cover slowly.

CAUTION

• Hold the fallboard with both hands when opening or closing it. Do not release it until it is fully opened or closed. Be careful to

avoid catching fingers (yours or others, especially children’s) between the fallboard and the unit.

• Do not apply excessive force when closing the fallboard. Applying excessive force to the fallboard when closing it could dam-

age the SOFT-CLOSE™ mechanism, and possibly result in injury to your hands and fingers caught under the closing fall-

board.

• Do not place anything (such as metal objects or pieces of paper) on top of the fallboard. Small objects placed on the fallboard

may fall inside the unit when the fallboard is opened and may be nearly impossible to remove. Once inside, they could cause

electric shock, short circuit, fire or other serious damage to the instrument.

CAUTION

When raising or lowering the music rest, do not release your hands from the music rest until it is all the way up or down.

To raise the music rest:

1 Gently open the front portion of the lid.

2 Pull the music rest up and toward yourself until it

remains at the desired angle. The music rest is

latched at angles of 35 degrees and 70 degrees.

3 Open the music brace.

CAUTION

Do not apply excessive force to the music brace. Doing so could

release the stopper of the music rest and the music rest could be

lowered suddenly, possibly resulting in injury to your hands and fin-

gers caught under the music rest.

Opening/Closing the Fallboard

Using the Music Rest

CAUTION

Be careful to avoid catching your fingers

when opening/closing the fallboard.

Playing the Keyboard

N3X Owner’s Manual •13

To lower the music rest:

1 Close the music brace.

2 Pull the music rest toward yourself as far as it will

go. When the music rest is at a 35 degree angle,

raise it to a 70 degree angle, then pull it toward

yourself.

3 Gently lower the music rest backward until it is all

the way down.

4 Gently close the front portion of the lid.

WARNING

Do not let children open or close the lid. Also, be careful to avoid catching fingers (yours or others, and especially those of chil-

dren) when raising or lowering the lid.

To open the lid

1 Gently open the front portion of the lid.

2 Hold the right side of the lid and raise it.

3 Raise the lid stay and carefully lower the lid so

that the end of the stay fits into the recess in the

lid.

WARNING

• Make sure that the end of the stay fits securely in the lid recess. If

the stay is not properly seated in the recess, the lid may fall, caus-

ing damage or injury.

• When the lid is open, do not place your head or other parts of your

body under it. Otherwise, severe injury could result if the lid

should fall.

• Be careful that you or others do not bump the stay while the lid is

raised. Also, make sure to close the lid when moving the instru-

ment. If bumped, the stay may be dislodged out of the lid recess

causing the lid to fall.

Opening/Closing the Lid

Do not hold here.

Hold here.

Lid stay

Playing the Keyboard

14 • N3X Owner’s Manual

To close the lid

1 Hold the lid stay and carefully raise the lid.

2 Hold the lid in its raised position and lower the lid

stay.

3 Carefully lower the lid.

When using the music rest, lower the music rest (page 13)

before going on to the next step.

4 Gently close the front portion of the lid.

1 Make sure the power switch on the instrument is

set to the off position.

2 Connecting the power cord

2-1 Set the voltage selector and insert the power cord plug to

the [AC IN] connector. Refer to the “Panel Controls and

Terminals” on page 10 for information on the location of

the [AC IN] connector.

WARNING

Make sure your instrument is rated for the AC voltage supplied in the area in which it is to be used. (The voltage rat-

ing appears on the name plate on the bottom panel). Connecting the unit to an inappropriate AC supply can seri-

ously damage the internal circuitry and may even pose a shock hazard!

2-2 Insert the plug on the other end of the power cord to a standard AC outlet.

Power Supply

Voltage Selector

Before connecting the AC power cord, check the setting of the voltage selector which is provided in some

areas. To set the selector for 110V, 127V, 220V or 240V main voltages, use a “minus” screwdriver to rotate

the selector dial so that the correct voltage for your region appears next to the pointer on the panel. The volt-

age selector is set at 240V when the unit is initially shipped. After the proper voltage has been selected, con-

nect the AC power cord to the AC IN and an AC wall outlet. A plug adaptor may be also provided in some

areas to match the pin configuration of the AC wall outlets in your area.

Do not hold here.

Hold here.

Lid stay

Power switch: off

Voltage

Selector

[AC IN] connector

(The shape of the plug differs depending

on the locale.)

Playing the Keyboard

N3X Owner’s Manual •15

WARNING

Use only the AC power cord supplied with the instrument. If the supplied power cord is lost or damaged and needs

to be replaced, contact your Yamaha dealer. The use of an inappropriate replacement can pose a fire and shock haz-

ard!

WARNING

The type of AC power cord provided with the instrument may be different depending on the country in which the

instrument was purchased. (In some areas a plug adaptor may be provided to match the pin configuration of the AC

wall outlets in your area.) Do NOT modify the plug provided with the instrument. If the plug will not fit the outlet,

have a proper outlet installed by a qualified electrician.

CAUTION

When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or mal-

function occurs, immediately turn off the power switch and disconnect the plug from the outlet.

NOTE

When disconnecting the power cord, first turn off the power, then follow this procedure in reverse order.

1 Grip the control panel located at the bottom left of

the instrument and slide it out towards you.

NOTICE

Do not pull on the [MASTER VOLUME] control to slide out the con-

trol panel.

2 Turn down the [MASTER VOLUME] control to

“MIN.”

3 Turn on the switch located on the bottom left of

the keyboard to turn the power on.

The [POWER] indicator located below the left end of the key-

board lights up. The display indicators flash in a pattern, indi-

cating the instrument is currently starting up, and stop flashing

when startup is completed.

NOTICE

Do not press any keys until the instrument has completely started up (approx. ten seconds after turning on the switch).

Doing so may cause some keys to not sound normally.

4 Playing the keyboard.

While playing the keyboard, adjust the volume level by using the [MASTER VOLUME] control located at the

left of the panel.

Turning the Power On/Off

Lights up

Off On

Power switch

Increases

the level.

Decreases

the level.

Playing the Keyboard

16 • N3X Owner’s Manual

5 Turn the switch off to turn the power off.

The [POWER] indicator turns off. Slide the control panel back into the bottom of the keyboard after use.

CAUTION

Even after the power switch is turned off, electricity is still flowing to the instrument at the minimum level. Remove the

electric plug from the outlet when the instrument is not to be used for extended periods of time, or during electrical

storms.

NOTICE

Press only the power switch when turning the power on. Any other operations, such as pressing the keys, buttons or ped-

als may cause the instrument to malfunction.

Auto Power Off function

To prevent unnecessary power consumption, this instrument features an Auto Power Off function that

automatically turns the power off if the instrument is not operated for approximately 30 minutes.

Disabling Auto Power Off (simple method)

Turn the power on while holding down the lowest key on the keyboard.

The indication “

PoF

” appears on the display briefly and Auto Power Off is disabled.

Disabling or enabling the Auto Power Off setting

While the power is on, simultaneously hold down the [FUNCTION] button and press the A5 key. Pressing the A5 key

repeatedly in this condition toggles between “

OFF

” (disabled) and “

” (enabled), and the setting appears on the

display.

NOTE

To turn the power on again after Auto Power Off has been enabled, turn the power switch to the off position once, and then back to the ON position.

Lowest key (A-1)

PoF

Highest key (C7)

Playing the Keyboard

N3X Owner’s Manual •17

To adjust the volume level by using the [MASTER VOLUME] control located at the left of the panel

while playing the keyboard.

CAUTION

Do not use this instrument at a high volume level for a long period of time, or your hearing may be damaged.

Intelligent Acoustic Control (IAC)

This function automatically adjusts and controls the sound quality according to the overall volume of the instrument.

Even when the volume is low, it permits both low sounds and high sounds to be clearly heard. Note that the IAC is

effective only from the sound output of the instrument speakers.

 To turn on/off the IAC:

While holding down [FUNCTION], press the C0 key repeatedly (as necessary).

Default setting: On

 To adjust the IAC Depth:

While holding down [FUNCTION], press one of the keys between A0–D#1.

Setting range: -3 (A0) – 0 (C1) – 3 (D#1)

Default setting: 0 (C1)

The higher the value, the more clearly that low and high sounds are heard at lower volume levels.

Adjusting the Master Volume

Increases

the level.

Decreases

the level.

C0 C1

(0)

(-3)

D#1 (3)

Lowest

key (

A-1)

Playing the Keyboard

18 • N3X Owner’s Manual

Since this instrument is equipped with two [PHONES] jacks, you

can connect two sets of standard stereo headphones. If you are

using only one set of headphones, insert a plug into either jack;

this automatically shuts off the speakers.

CAUTION

Avoid listening to the instrument at a high volume level through headphones

for a long period of time, to prevent hearing damage.

NOTE

The TRS is turned off when headphones are connected. Press the [TRS] button to turn it on (page 25).

NOTE

When the TRS (page 25) is on, sound can be heard to some degree even when the headphones are connected.

Reproducing the Natural Sound Distance Sensation (when using Headphones)—Binaural Sampling

and Stereophonic Optimizer

This instrument features two advanced technologies that allow you to enjoy exceptionally realistic, natural sound,

even though listening on headphones.

 Binaural Sampling (“CFX Grand” Voice only)

Binaural sampling is a method that uses two special microphones set at the ear position of a performer and records

the sound from a piano as it is. Listening to the sound with this effect through headphones gives the impression of

being immersed in the sound, as if it was actually emanating from the piano. Moreover, you can enjoy the sound

naturally for a long time without ear strain. When the default voice, “CFX Grand” (page 20) is selected, connecting

the headphones automatically enables the binaural sampling sound.

 Stereophonic Optimizer (Voices other than “CFX Grand”)

The Stereophonic Optimizer is an effect which reproduces natural sound distance like the sound of binaural sam-

pling even though you hear it on headphones. When the voice except “CFX Grand” (page 20) is selected, connect-

ing the headphones makes this Stereophonic Optimizer effective.

Turning the Binaural Sampling and Stereophonic Optimizer function on/off

When headphones are connected, the sound from this instrument changed to the sound of Binaural Sampling or the

sound enhanced with the Stereophonic Optimizer. Since these sounds are optimized for listening with headphones,

we recommend that you set this function to “OFF” (as described below).

While holding down [PIANO/VOICE] button, press the C6 key repeatedly (if necessary) to turn this function on/off.

The specified value is shown on the display while both controls are held.

Default setting: On

Using Headphones

You should turn these functions off when:

• Playing the sound of this instrument with an external powered speaker system or a mixer, while monitoring the sound

output from this instrument on connected headphones.

• Making an audio recording (page 34) and then playing that recorded audio Song through speakers.

(Make sure to turn off these functions before audio recording.)

NOTE

Before connecting an external powered speaker system or a mixer, be sure to read “Using an External Stereo System for Playback—AUX OUT [L/L+R] [R] jacks (unbalanced)” (page

42) or “Connecting to a Mixer—OUTPUT [L] [R] jacks (Balanced)” (page 42).

Standard stereo

phone plug

Highest key (C7)

Playing the Keyboard

N3X Owner’s Manual •19

The instrument has three pedals that produce a range of expressive effects similar to those produced by

the pedals on an acoustic piano.

Damper Pedal (Right)

Pressing this pedal will sustain notes longer. Releasing this pedal immediately stops

(damps) any sustained notes. The damper pedal features a half-pedal function.

 Half-pedal function

This function allows the sustain length to vary depending on how far the pedal is

pressed. The farther you press the pedal, the more the sound sustains. For example, if

you press the damper pedal and all notes you are playing sound a bit murky and loud

with too much sustain, you can release the pedal half way to subdue the sustain (murk-

iness).

Sostenuto Pedal (Center)

Pressing this pedal while holding the notes will sustain the pressed notes (as if the

damper pedal had been pressed), but all subsequently played notes will not be sus-

tained. This makes it possible to sustain a chord, for example, while the other notes are

played “staccato.”

Soft Pedal (Left)

Pressing this pedal will reduce the volume and slightly change the timbre of the notes.

The notes played before this pedal is pressed are not affected.

Using the Pedals

If you press and hold the

damper pedal here, all the

notes shown will be sus-

tained.

If you press and hold the soste-

nuto pedal here, only the notes

held at this timing will be sus-

tained.

20 • N3X Owner’s Manual

Basic Operations and More

 To select the CFX Grand Voice:

Simply press [PIANO/VOICE].

 To select a different Voice:

While holding down [PIANO/VOICE], press [+] or [-].

Voice List

*VRM: Simulated string resonance sound with physical modeling when the damper pedal is pressed or keys

are pressed. Refer to page 26 for details.

Selecting a Voice

NOTE

To understand the characteristics of various

voices, listen to demo songs for each voice

(page 21).

Display Voice name Descriptions VRM*

CFX Grand

Four-channel Voice featuring multi sampling of Yamaha’s

CFX flagship concert grand piano sound, with wide dynamic

range for maximum expressive control. It is suitable for play-

ing in any music genre and style. When headphones are

connected, this Voice is automatically changed to “Binaural

CFX Grand” (below).



Binaural CFX

Grand

Yamaha’s CFX flagship concert grand piano sound sampled

by Binaural Sampling, the method optimized for headphone

use. Listening this through headphones gives the impres-

sion of being immersed in the sound, as if it was actually

emanating from the piano. This Voice is selected automati-

cally when headphones are connected. Refer to page 18 for

details. (This Voice cannot be selected following the proce-

dure of “Selecting a Voice” instructions above.)



Bösendorfer

Imperial

The sound of the famed Vienna-made Bösendorfer flagship

grand piano, utilizing four-channel sampling. This Voice has

a rich and captivating sound, ideal for expressing the most

delicate and tender musical passages.



Bright Grand

Bright piano sound. Good for clear expression and “cutting

through” other instruments in an ensemble.



Bösendorfer Grand

The Bösendorfer grand piano sound with a lively attack and

brilliant presence.



Pop Grand

A bright, richly metallic sound ideal for pop music styles and

for playing in ensembles.



Stage E.Piano

The sound of an electric piano using hammerstruck metallic

“tines.” Soft tone when played lightly, and an aggressive tone

when played hard.

DX E.Piano

An electronic piano sound produced by an FM synthesizer.

The tone will change as you vary your playing touch. Ideal

for popular music.

Vintage E.Piano

A different type of electric piano sound than Stage E.piano.

Widely used in rock and popular music.

Harpsichord 8’

The sound of the instrument frequently used in baroque

music. Variations in playing touch will not affect the volume,

and a characteristic sound will be heard when you release

the key.

Harpsichord 8’+4’

A harpsichord with an added upper octave. Produces a more

brilliant sound. Variations in playing touch will not affect the

volume.

Main Operations

Страница загружается...

Yamaha N3X Инструкция по применению

Похожие модели бренда