Yamaha ME02R Инструкция по применению

Бренд: Yamaha

Модель: ME02R

Тип: Инструкция по применению

Yamaha ME02R расширит память вашего микшера в семь раз, до 7 Мб, что сделает его еще более универсальным и удобным в использовании. Данный комплект расширения должен быть установлен авторизованным специалистом по обслуживанию. Перед установкой ME02R96 обязательно сохраните все важные данные с устройства 02R96 на внешнее MIDI-устройство. Процесс установки сотрет всю пользовательскую память устройства и сбросит все настройки до значений по умолчанию. Плата ME02R96 чувствительна к электростатическому разряду.

ME02R96

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

ME02R96

Owner’s Manual

Thank you for your purchase of the YAMAHA ME02R96 memory expansion kit for the 02R96 mixer.

By replacing the original CPU board with this ME02R96 expansion board, you will expand your

mixer’s automix memory to 7MB—a sevenfold increase that will make your mixer even more versa-

tile and even easier to use.

Please read through the following precautions carefully before having the serviceperson install this

ME02R96 expansion kit. Be sure to retain the manual in a safe place.

Precautions

WARNINGS

Failure to observe the following warnings may lead to fatality or serious injury from ﬁre or

electric shock.

CAUTIONS

Failure to observe the following cautions may lead to injury, or may result in damage to

equipment or other property.

●

Do not attempt to disassemble or modify the

ME02R96 board. Do not apply excessive force to

board connectors or other board components.

(Mishandling of the board may lead to shock, ﬁre

hazard, or equipment failure.)

●

Be sure to unplug the 02R96 main unit from the

power supply before installing the ME02R96

board (to eliminate shock hazard).

●

Be careful to avoid catching or snagging ﬁngers

while carrying out the installation.

●

Before starting installation, be sure to save all

important data from the 02R96 unit to an external

MIDI device. This installation process will clear all

of the unit’s user memory and will reset all set-

tings to their defaults.

●

When handling the ME02R96 board, do not

touch the board’s metallic leads (pins). (Pins are

sharp and may cause hand cuts.)

●

The ME02R96 board is electrostatic-sensitive.

Before handling the board, you should brieﬂy

touch the main unit’s metal casing with your bare

hand so as to drain off any static charge from

your body.

●

Be sure to install the included lithium battery. This

is a backup battery that is required maintain the

data in the 02R96’s expanded memory.

The ME02R96 expansion kit must be installed by an authorized

serviceperson. Please contact a local Yamaha dealer or a service

center to arrange for installation. Do not attempt to install the

ME02R96 on your own.

1. IMPORTANT NOTICE: DO NOT MOD-

IFY THIS UNIT!

This product, when installed as indicated

in the instructions contained in this man-

ual, meets FCC requirements. Modiﬁca-

tions not expressly approved by Yamaha

may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT: When connecting this

product to accessories and/or another

product use only high quality shielded

cables. Cable/s supplied with this prod-

uct MUST be used. Follow all installation

instructions. Failure to follow instructions

could void your FCC authorization to use

this product in the USA.

3. NOTE: This product has been tested

and found to comply with the require-

ments listed in FCC Regulations, Part 15

for Class “B” digital devices. Compliance

with these requirements provides a rea-

sonable level of assurance that your use

of this product in a residential environ-

ment will not result in harmful interfer-

ence with other electronic devices. This

equipment generates/uses radio fre-

quencies and, if not installed and used

according to the instructions found in the

users manual, may cause interference

harmful to the operation of other elec-

tronic devices. Compliance with FCC

regulations does not guarantee that

interference will not occur in all installa-

tions. If this product is found to be the

source of interference, which can be

determined by turning the unit “OFF”

and “ON”, please try to eliminate the

problem by using one of the following

measures:

Relocate either this product or the

device that is being affected by the inter-

ference.

Utilize power outlets that are on different

branch (circuit breaker or fuse) circuits

or install AC line ﬁlter/s.

In the case of radio or TV interference,

relocate/reorient the antenna. If the

antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type

cable.

If these corrective measures do not pro-

duce satisfactory results, please contact

the local retailer authorized to distribute

this type of product. If you can not locate

the appropriate retailer, please contact

Yamaha Corporation of America, Elec-

tronic Service Division, 6600 Orangetho-

rpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by Yamaha Corpora-

tion of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

ME02R96

ENGLISH

* Please dispose of used batteries in accordance with local regulations.

* Illustrations in this manual are for explanatory purposes only, and may not match the actual appearance of

the product.

* Company names and product names used herein are trademarks or registered trademarks of their respec-

tive owners.

* Use of the software and this manual is governed by the license agreement which the purchaser fully agrees

to upon breaking the seal of the software packaging. (Please read carefully the important information and

the Software Licensing Agreement of the Studio Manager’s installation guide included with 02R96 before

installing the software.)

* Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp.

reserves the right to change or modify products or speciﬁcations at any time without prior notice. Since

speciﬁcations, equipment or options may not be the same in every locale, please check with your Yamaha

dealer.

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or

data that is lost or destroyed.

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af

samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som

rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmista-

jan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

NEDERLAND THE NETHERLANDS

●

Dit apparaat bevat een lithium batterij voor

geheugen back-up.

●

This apparatus contains a lithium battery for

memory back-up.

●

Raadpleeg uw leverancier over de verwijde-

ring van de batterij op het moment dat u het

apparaat ann het einde van de levensduur

afdankt of de volgende Yamaha Service

Afdeiing:

Yamaha Music Nederland Service Afdeiing

Kanaalweg 18-G, 3526 KL UTRECHT

Tel. 030-2828425

●

For the removal of the battery at the moment

of the disposal at the end of the service life

please consult your retailer or Yamaha Ser-

vice Center as follows:

Yamaha Music Nederland Service Center

Address: Kanaalweg 18-G, 3526 KL

UTRECHT

Tel: 030-2828425

●

Gooi de batterij niet weg, maar lever hem in

als KCA.

●

Do not throw away the battery. Instead, hand

it in as small chemical waste.

ME02R96

ENGLISH

●

Note About Versions and Upgrades

System software:

The ME02R96 includes system version 1.20 or higher, and is not compatible with pre-V1.20 soft-

ware. Before upgrading your 02R96 again in the future, be sure that your updater program is V1.20

or higher.

Studio Manager:

The ME02R96 is not compatible with Studio Manager versions prior to V1.1.1. If your version is

older than V1.1.1, please replace it by installing the Studio Manager version included on the accom-

panying CD-ROM. For information about how to carry out the installation, refer to Studio Manager’s

installation guide.

Note that Macintosh system requirements are now as indicated in the table below.

Macintosh System Requirements

For the latest information about System software and Studio Manager, please visit our website at:

www

.yamahaproaudio.com.

●

Save the Data from the 02R96

Press the DISPLAY ACCESS [MIDI] key to open the Bulk Dump page.

Set CATEGORY to ALL, select the TRANSMIT button, and then press the [ENTER] key to

start the save.

Computer A Macintosh G3/233 MHz or better and a USB port

OS Mac OS 8.6 to 9.2.2 (Mac OS X not supported)

Memory 120 MB or more of free memory (Virtual memory must be turned off)

Hard Disk 7 MB or more

Display 1024

768 pixels, 256 colors or higher

1280

1024, 32,000 colors recommended

Other OMS 2.3.3 or later

Note: If you are using a PowerBook on battery power, open the Energy Save

control panel, and in Advanced Settings, Additional Power Savings, turn off

Allow processor cycling.

The board installation procedure will clear all 02R96 user memory, and will reset all 02R96 settings to

their defaults. Before starting installation, use the following procedure to save the data from the 02R96

into an external MIDI device. You can then restore the data after completing the installation.

As an alternative, you can use Studio Manager to save the 02R96 data into a computer. For details,

refer to the Studio Manager owner’s manual (PDF ﬁle).

ME02R96

ENGLISH

●

Install the ME02R96 Expansion Kit

~The following instructions are intended for use by authorized serviceper-

sons only.~

Detach and Raise the Control Panel

Turn off the 02R96 power switch, and unplug the 02R96 power cord from the power supply.

If SP02R96 side panels are installed on the 02R96, remove both of these panels (one from the

left, and the other from the right). To remove each panel, remove 6 screws as shown below

(for a total of 12 screws).

For more information about SP02R96 side panels, refer to the 02R96 owner’s manual.

When removing each screw, note its location and be sure to return it to the same place when reassem-

bling. Screws come in various sizes and are not interchangeable.

This kit is not user-installable. Users should contact a local

Yamaha dealer or a service center to arrange for installation by a

Yamaha-authorized serviceperson.

02R96

SP02R96

(Side Panel)

6 Screws

ME02R96

ENGLISH

If the MB02R96 peak meter bridge is installed on the 02R96, remove it. First disconnect the

bridge cable from the METER connector on the 02R96. Then remove the 4 screws holding the

bridge in place (as shown below), and remove the bridge.

2 Screws

METER Connector

2 Screws

02R96

ME02R96

ENGLISH

Remove the screws indicated in the illustration below: 7 screws from the left side, 7 screws

from the right side, 7 screws from the front, and 7 screws (or 5 screws, if 2 were already

removed at Step 3) from the rear.

Hold onto the LCD, and lift up the rear of the control panel.

Secure the raised control panel in place, so that it does not fall back down.

Positioning

Screw

Position-

ing Screw

LCD

7 Screws

7 Screws

7 Screws

Positioning

Screw

7 Screws

Position-

ing Screw

LCD

ME02R96

ENGLISH

Install the ME02R96 Expansion Board and the Battery

Disconnect the 2 flat cables from the connectors

on the CPU board.

The cables are connected to white connectors.

Before disconnecting each cable, pull the con-

nector latch up as shown in the illustration.

Remove the 4 screws holding the CPU board in place, and remove the CPU board.

Mount the ME02R96 board.

Connect the two black connectors on the underside of the ME02R96 board to the two black

connectors on the 02R96. Then fasten the ME02R96 into place using 4 screws (the 4 screws

you removed above, or the 4 screws included in the kit).

Reconnect the 2 flat cables.

To reconnect: Push the latch down, then insert the cable so that the red line on the cable is

aligned with the

▼

mark on the board.

Install the supplied lithium battery. This is a backup battery that is required to maintain data in

the 02R96 unit’s expanded memory.

When installing the expansion board, you can use either these 4 screws or else the 4 screws included

in the kit. If you reuse these original screws, you will not need the screws in the kit.

CPU

4 Screws

Lithium Battery

Flat Cable

Latch

ME02R96

ENGLISH

Reattach the Control Panel

Lower the control panel back into place. Then refasten with the original screws, in the following

order: front panel first, then the sides, and then the rear. When fastening each panel, always

fasten the positioning screw first (see illustrations on page 6 above).

If applicable:

Reinstall the MB02R96 peak meter bridge and/or the SP02R96 side panels by

reversing the removal procedures given on page 4 and 5 above.

●

Restoring the Saved 02R96 Data

If you saved the 02R96 data to an external MIDI device as described on page 3 above, you can now

restore that data as follows.

After completing the kit installation, turn on the 02R96 power. The start-up screen displays the

message

MEMORY EXPANDED

Press the DISPLAY ACCESS [MIDI] key to open the Bulk Dump page.

Set the CATEGORY to ALL, select the REQUEST button, and then press the [ENTER] key.

●

Kit Contents

European models

Purchaser/User Information speciﬁed in EN55103-1 and EN55103-2.

Conforms to Environments: E1, E2, E3 and E4

Before screwing in the control panel, check to make sure that you have not left any loose screws or

tools inside the 02R96 casing. Loose objects left in the casing may cause damage to the equipment.

It is not possible to load automix data that exceeds the mixer’s automix memory capacity (7MB with

the ME02R96 installed; 1MB if it is not installed). If you attempt to load such data, the 02R96 will dis-

play an appropriate message and will execute the load. Any data already existing in the 02R96 will

remain unchanged.

ME02R96 Expansion Board

Lithium battery

4 Screws

ME02R96 Owner’s Manual (this booklet)

CD-ROM (Studio Manager)

Yamaha Manual Library

http://www2.yamaha.co.jp/manual/english/

Yamaha ME02R Инструкция по применению

Бренд: Yamaha

Модель: ME02R

Тип: Инструкция по применению

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha ME02R Owner's manual
français: Yamaha ME02R Le manuel du propriétaire
italiano: Yamaha ME02R Manuale del proprietario
español: Yamaha ME02R El manual del propietario
Deutsch: Yamaha ME02R Bedienungsanleitung
Nederlands: Yamaha ME02R de handleiding
português: Yamaha ME02R Manual do proprietário
dansk: Yamaha ME02R Brugervejledning
polski: Yamaha ME02R Instrukcja obsługi
čeština: Yamaha ME02R Návod k obsluze
svenska: Yamaha ME02R Bruksanvisning
日本語: Yamaha ME02R 取扱説明書
Türkçe: Yamaha ME02R El kitabı
română: Yamaha ME02R Manualul proprietarului

Yamaha ME02R Инструкция по применению

Yamaha ME02R Инструкция по применению

на других языках

Похожие модели бренда