Yamaha RX-V395 Инструкция по применению
- Категория
- Ресиверы
- Тип
- Инструкция по применению
Это руководство также подходит для
RX-V395
NATURAL SOUND AV RECEIVER
AMPLI-TUNER AUDIO-VIDEO
OWNER’S MANUAL
MODE D’EMPLOI
UCA
SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
● Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
1. Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2. Retain Instructions – The safety and operating instructions
should be retained for future reference.
3. Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4. Follow Instructions – All operating and other instructions
should be followed.
5. Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6. Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the
manufacturer.
6A. A unit and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
unit and cart combination to overturn.
7. Wall or Ceiling Mounting – The unit should be mounted to
a wall or ceiling only as recommended by the
manufacturer.
8. Ventilation – The unit should be situated so that its location
or position does not interfere with its proper ventilation.
For example, the unit should not be situated on a bed,
sofa, rug, or similar surface, that may block the ventilation
openings; or placed in a built-in installation, such as a
bookcase or cabinet that may impede the flow of air
through the ventilation openings.
9. Heat – The unit should be situated away from heat sources
such as radiators, stoves, or other appliances that produce
heat.
10. Power Sources – The unit should be connected to a power
supply only of the type described in the operating
instructions or as marked on the unit.
11.Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12. Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13. Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14. Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15. Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or exhibits
a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16. Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17. Power Lines – An outdoor antenna should be located
away from power lines.
18.Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
English
19.For US customers only:
Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC
– NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound
come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
1
2
SUPPLIED ACCESSORIES ● After unpacking, check that the following parts are included.
ACCESSORIES FOURNIS ● Après le déballage, vérifier que les pièces suivantes sont incluses.
● Indoor FM Antenna
● Antenne FM intérieure
6CH
2CH
● Remote Control Transmitter
● Emetteur de télécommande
● Batteries (size AAA, R03, UM-4) (4)
● Piles (taille AAA, R03, UM-4) (4)
● AM Loop Antenna
● Cadre-antenne AM
● Antenna adapter (U.S.A. and Canada models only)
● Adaptateur d’antenne (Modèles pour les États-Unis et le
Canada seulement)
3
English
● 5 Speaker Configuration
(Power Amp. Section)
Main: 60W + 60W (8Ω) RMS Output
Power, 0.04% THD,
20–20,000 Hz
Center: 60W (8Ω) RMS Output Power,
0.04% THD, 20–20,000 Hz
Rear: 60W + 60W (8Ω) RMS Output
Power, 0.04% THD,
20–20,000 Hz
● Digital Sound Field Processor
● Dolby Pro Logic Surround Decoder
● Theater-like Sound Experience by the
Combination of Dolby Pro Logic and
YAMAHA DSP Technology (CINEMA DSP)
● Automatic Input Balance Control for
Dolby Pro Logic Surround
● Test Tone Generator for Easier Speaker
Balance Adjustment
Thank you for selecting this YAMAHA AV receiver.
FEATURES
CONTENTS
● 3 Center Channel Modes
(NORMAL/WIDE/PHANTOM)V395RDS o
● 40-Station Random Access Preset Tuning
● Automatic Preset Tuning
● Preset Station Shifting Capability (Preset
Editing)
● IF Count Direct PLL Synthesizer Tuning
System
● 6-Channel External Decoder Input for
Dolby Digital, DTS, and Other Future
Formats
● Video Signal Input/Output Capability
● SLEEP Timer
● Universal Remote Control Transmitter
with Preset Manufacturer Codes
SUPPLIED ACCESSORIES............................2
FEATURES .....................................................3
CAUTION ........................................................4
NOTES ABOUT THE REMOTE CONTROL
TRANSMITTER...............................................5
PROFILE OF THIS UNIT ................................6
SPEAKER SETUP ..........................................7
CONNECTIONS..............................................8
CONTROLS AND THEIR FUNCTIONS ........14
SPEAKER BALANCE ADJUSTMENT ..........19
BASIC OPERATIONS ...................................22
TUNING OPERATIONS ................................26
PRESET TUNING .........................................27
REMOTE CONTROL TRANSMITTER..........30
USING DIGITAL SOUND FIELD
PROCESSOR (DSP) ....................................36
SETTING THE SLEEP TIMER......................40
SETUP CODES ............................................41
TROUBLESHOOTING ..................................42
SPECIFICATIONS ........................................43
LIST OF MANUFACTURER’S CODES.........87
4
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the unit to rain or water.
3. Never open the cabinet. If something drops into the set,
contact your dealer.
4. Do not use force on switches, controls or connection wires.
When moving the unit, first disconnect the power plug and
the wires connected to other equipment. Never pull the
wires themselves.
5. The openings on the unit cover assure proper ventilation of
the unit. If these openings are obstructed, the temperature
inside the unit will rise rapidly. Therefore, avoid placing
objects against these openings, and install the unit in a
well-ventilated area to prevent fire and damage.
<China, U.K. and Europe models only>
Be sure to allow a space of at least 20 cm behind, 20 cm
on the both sides and 30 cm above the top panel of the
unit to prevent fire and damage.
6. Always set the VOLUME control to “– ∞” before starting
the audio source play. Increase the volume gradually to an
appropriate level after playback has been started.
7. Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding that
the unit is faulty.
9. When not planning to use this unit for long periods of time
(i.e., vacation, etc.), disconnect the AC power plug from
the wall outlet.
10.To prevent lightning damage, disconnect the AC power
plug and antenna cable when there is an electrical storm.
11.Grounding or polarization – Precautions should be taken
so that the grounding or polarization of an appliance is not
defeated.
12.Do not connect audio equipment to the AC outlet on the
rear panel if the equipment requires more power than the
outlet is rated to provide.
13.Voltage Selector <China and General models only>
The voltage selector on the rear panel of this unit must
be set for your local main voltage BEFORE plugging
into the AC power supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.
IMPORTANT
Please record the serial number of this unit in the space
below.
Model:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off. This state is called the standby mode.
In this state, this unit is designed to consume a very small
quantity of power.
FREQUENCY STEP switch <China and General models
only>
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP switch (located
on the rear panel) according to the frequency spacing in
your area.
Before setting this switch, disconnect the AC power plug of
this unit from the AC outlet.
For Canadian Customers
To prevent electric shock, match wide blade of plug to wide
slot and fully insert.
This Class B digital apparatus complies with CANADIAN
ICES-003
5
English
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Battery replacement
When you notice a decrease in the operating range of the
remote control transmitter, the batteries are weak. Replace all
batteries with new ones.
Notes
● Use only AAA, R03, UM-4 batteries for replacement.
● Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
● Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
● If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
● When replacing batteries, try to install the new batteries
within two minutes of removing the old batteries, or
information stored in the remote control transmitter may be
lost.
2
1
3
LR
Remote control
sensor
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described on the right.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L
or coloured RED. Making sure that neither core is
connected to the earth terminal of the three pin plug.
Within approximately
6 m (19.7 feet)
Remote control transmitter operation range
Notes
● There should be no large obstacles between the remote
control transmitter and the main unit.
● If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp,
etc.), it might cause the remote control transmitter not to
work correctly. In this case, reposition the main unit to avoid
direct lighting.
6
PROFILE OF THIS UNIT
You are the proud owner of a Yamaha stereo receiver – an extremely sophisticated audio component. The Digital Sound Field
Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to
bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system,
and this unit will sonically transform your room into a wide range of listening environments – movie theater, concert hall, and so on.
In addition, you get incredible realism from sources encoded with Dolby Surround using the built-in Dolby Pro Logic Surround
decoder.
Please read this owner’s manual carefully and store it in a safe place for later reference.
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to
the sound of a live performance, but chances are you’ll still
notice something missing: the acoustic environment of the live
concert hall. Extensive research into the exact nature of the
sonic reflections that create the ambience of a large hall has
made it possible for Yamaha engineers to bring you this same
sound in your own listening room, so you’ll feel all the sound of
a live concert.
Dolby Pro Logic Surround
This unit employs a Dolby Pro Logic Surround decoder similar
to professional Dolby Stereo decoders used in many movie
theaters. By using the Dolby Pro Logic Surround decoder, you
can experience the dramatic realism and impact of Dolby
Surround movie theater sound in your own home. Dolby Pro
Logic employs a four channel five speaker system. The Pro
Logic Surround system divides the input signal into four levels:
the left and right main channels, the center channel (used for
dialog), and the rear surround sound channel (used for sound
effects, background noise, and other ambient noises). The
center channel allows listeners seated in even less-than-ideal
positions to hear the dialog originating from the action on the
screen while experiencing good stereo imaging.
Dolby Surround is encoded on the sound track of pre-recorded
video tapes, laser discs, and some TV/cable broadcasts. When
you play a source encoded with Dolby Surround on this unit,
the Dolby Pro Logic Surround decoder decodes the signal and
distributes the surround-sound effects.
Dolby Pro Logic Surround + DSP
A Dolby Surround sound system shows its full ability in a large
movie theater, because movie sounds are originally designed
to be reproduced in a large movie theater using many
speakers. It is difficult to create a sound environment similar to
that of a movie theater in your listening room, because the
room size, materials of inside walls, the number of speakers,
etc. of your listening room is much different from those of a
movie theater.
Yamaha DSP technology made it possible to present you with
nearly the same sound experience as that of a large movie
theater in your listening room by compensating for lack of
presence and dynamics in your listening room with its original
digital sound fields combined with Dolby Surround sound field.
Furthermore, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of a variety of venues such as an actual concert
hall, theater, etc. to allow you to accurately recreate one of
several actual live performance environments, all in your own
home.
This Dolby Pro Logic Surround Decoder employs a digital
signal processing system. This system improves the stability of
sound at each channel and minimizes crosstalk between
channels, so that positioning of sounds around the room is
more accurate compared with conventional analog signal
processing systems.
In addition, this unit features a built-in automatic input balance
control. This always assures you the best performance without
manual adjustment.
Manufactured under license from Dolby Laboratories. “Dolby”,
“AC-3”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
The combination of Dolby Pro Logic Surround and DSP is used
on the sound field program “
PRO LOGIC ENHANCED”.
CINEMA DSP
The YAMAHA “CINEMA DSP” logo indicates these programs
are created by the combination of Dolby Pro Logic and
YAMAHA DSP technology.
Digital Sound Field Processing
7
English
SPEAKER SETUP
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with
this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker
Configuration” shown below.)
The main speakers are used for the majority of the sound output as well as effect sounds. The rear speakers are used for the effect
and surround sounds, and the center speaker is for the center sounds (dialog, etc.) within programs encoded with Dolby Surround.
The center speaker needs to be equal in power to the main speakers, though the rear speakers should be slightly lower in power.
However, all the speakers should have high enough power handling to accept the maximum output of this unit.
5-Speaker Configuration
This configuration is the most effective and recommended one.
In this configuration, the center speaker is necessary as well as
the rear speakers. If the program DOLBY PRO LOGIC or
DOLBY PRO LOGIC ENHANCED is selected, conversations
will be output from the center speaker and the ambience will be
excellent.
● Set the center channel mode to the “NORMAL” or “WIDE”
position. (For details, refer to page 20.)
Main L
Main R Main L
Main R
SPEAKER PLACEMENT
The recommended 5-speaker configuration requires a pair of main speakers, a center speaker, and a pair of rear speakers
(sometimes referred to as surround speakers). When arranging your speakers, refer to the illustration and information below.
Main: Position the main speakers at equal distances away
from the listening position and at equal distances on
either side of the center speaker.
Rear: Position rear speakers directly behind the listening
position at a height of approximately 1.8m (6 feet) up
from the floor, facing slightly inward. If the speakers
cannot be placed behind the listening position, they
may also be placed at the side of the listening
position, facing toward the listening position.
Center: Position the center speaker directly in front of the
listening position between the main speakers. (When
placing on or near a television, use a magnetically
shielded speaker to avoid unwanted interference.)
4-Speaker Configuration
The center speaker is not used in this configuration. If the
program DOLBY PRO LOGIC or DOLBY PRO LOGIC
ENHANCED is selected, the center sound is output from the
left and the right main speakers. However, the sound effect of
other programs can be the same as that of the 5-speaker
configuration.
● Be sure to set the center channel mode to the “PHANTOM”
position. (For details, refer to page 20.)
SPEAKER CONFIGURATION
Center
Dialogue
Surround sound
Rear L
Rear R
Rear L
Rear R
Dialogue
Surround sound
Main R
Center
Main L
Rear L
Rear R
TV set
8
FM
ANT
AM
ANT
GND
75ΩUNBAL.
GND
MONITOR
OUT
DVD/LD
TV/DBS
IN
OUT
VCR
IN
OUT
VCR
PHONO
CD
DVD/LD TV/DBS
1
3
4
A OR B
: 4
Ω
MIN. /SPEAKER
A B
: 8
Ω
MIN. /SPEAKER
:
6
Ω
MIN. /SPEAKER
:
6
Ω
MIN. /SPEAKER
A OR B
: 8
Ω
MIN. /SPEAKER
A B
:
16
Ω
MIN. /SPEAKER
:
8
Ω
MIN. /SPEAKER
:
8
Ω
MIN. /SPEAKER
MAIN
R
L
SURROUND
R
L
CENTER
SUB
WOOFER
6CH DISCRETE INPUT
VIDEO SIGNAL
TAPE/MD
AUDIO SIGNAL
AC OUTLETS
MAIN
CENTER
REAR
MAIN
CENTER
REAR
I00W MAX. TOTAL
SWITCHED
IN OUT
(REC)(PLAY)
R
REAR
(SURROUND)
FREQUENCY
STEP
50kHz
/ 9kHz
100kHz
/10kHz
FM / AM
SET BEFORE POWER ON
IMPEDANCE SELECTOR
A
B
VOLTAGE SELECTOR
GND
OUTPUT
AUDIO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
VIDEO IN
AUDIO OUT
VIDEO OUT
LINE OUT
LINE IN
OUTPUT
VIDEO OUT
AUDIO OUT
CONNECTIONS WITH OTHER COMPONENTS
Never plug in this unit and other components until all connections are completed.
When making connections between this unit and other components, be sure all connections are made correctly; that is to say L (left)
to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
* If you have YAMAHA components numbered as 1, 3, 4, etc. on the rear panel, connections can be made easily by connecting
the output (or input) terminals of each component to the same-numbered terminals on this unit.
Turntable
Monitor TV TV/Satellite tuner Video cassette recorder
To AC outlet
LD player,
DVD player, etc.
Tape deck,
MD recorder, etc.
CD player
*1
*2
*3
*1 Ground (GND) terminal (For turntable use)
Connecting the ground wire of the turntable to the GND
terminal will normally minimize hum, but in some cases
better results may be obtained with the ground wire
disconnected.
*2 Voltage Selector <China and General models only>
The voltage selector on the rear panel of this unit must be
set for your local main voltage BEFORE plugging into the
AC power supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
*3 AC OUTLETS (SWITCHED)
<Europe, Canada, U.S.A., China and General models>
.....................................................2 SWITCHED OUTLETS
<U.K. and Australia models> .......... 1 SWITCHED OUTLET
Use these to connect the power cords from your
components to this unit.
The power to the SWITCHED AC OUTLETS is controlled
by this unit’s STANDBY/ON switch or the provided remote
control transmitter’s POWER
/I key. These outlets will
supply power to any component whenever this unit is
turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLETS is 100 watts.
CONNECTIONS
<General model>
9
English
Connecting an external decoder for Dolby Digital, DTS and other future formats
or a DVD player, etc.
If you have a separate Dolby Digital, DTS or other format decoder, or if you have a DVD player or other component which
incorporates a Dolby Digital, DTS, or other format decoder, its 6 channel discrete outputs can be connected to the 6CH DISCRETE
INPUT terminals of this unit.
(Example)
Dolby Digital decoder
RF Demodulator
Laserdisc player or other unit with
Dolby Digital RF (AC-3 RF) output
<General model>
FM
ANT
AM
ANT
GND
75ΩUNBAL.
GND
IN
OUT
VCR
PHONO
CD
DVD/LD TV/DBS
1
3
4
MAIN
R
L
SURROUND
R
L
CENTER
SUB
WOOFER
6CH DISCRETE INPUT
TAPE/MD
AUDIO SIGNAL
IN OUT
(REC)(PLAY)
MONITOR
OUT
DVD/LD
TV/DBS
IN
OUT
VCR
VIDEO SIGNAL
FREQUENCY
STEP
50kHz
/
9kHz
100kHz
/10kHz
FM / AM
DOLBY DIGITAL
RF (AC-3 RF) OUT
DOLBY DIGITAL
RF (AC-3 RF) IN
DIGITAL
IN
DIGITAL
OUT
VIDEO OUT
AUDIO OUT
6CH DISCRETE OUTPUT
SUB
WOOFER
CENTER SURROUNDMAIN
Notes
● The laserdisc player (or other unit) must be also connected
to the DVD/LD (or TV/DBS) AUDIO SIGNAL input terminals
of this unit to play a source encoded with Dolby Pro Logic
Surround or in normal stereo (or monaural).
● The discrete signals input to this unit cannot be recorded by
a tape deck, MD recorder or VCR. To record a source
played on the laserdisc player (or another unit), it must be
connected to the DVD/LD (or TV/DBS) AUDIO/VIDEO
SIGNAL input terminals of this unit.
● If you made no connection to the SUB WOOFER input
terminal of this unit or you will not use a subwoofer, you
should be able to make a setting on the decoder to
distribute SUB WOOFER channel signals to the right and
left MAIN output terminals.
For details, refer to the owner’s manual supplied with the
decoder.
10
CONNECTING SPEAKERS
Main speakers A
Right Left
Subwoofer system
Main speakers B
Left
Right
Right Left
Rear speakers
Center speaker
<General model>
MAIN
OUTPUT
SUB
WOOFER
SPEAKERS
R
CENTER
REAR
(SURROUND)
A OR B
: 4
Ω
MIN. /SPEAKER
A B
: 8
Ω
MIN. /SPEAKER
:
6
Ω
MIN. /SPEAKER
:
6
Ω
MIN. /SPEAKER
A OR B
: 8
Ω
MIN. /SPEAKER
A B
:
16
Ω
MIN. /SPEAKER
:
8
Ω
MIN. /SPEAKER
:
8
Ω
MIN. /SPEAKER
MAIN
CENTER
REAR
MAIN
CENTER
REAR
SET BEFORE POWER ON
IMPEDANCE SELECTOR
CAUTION
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
A
B
Note
Use speakers with the specified impedance shown on the
rear of this unit.
Note on main speaker connections:
One or two speaker systems can be connected to this unit. If
you use only one speaker system, connect it to either the
SPEAKERS A or B terminals.
Note on subwoofer connection:
You may wish to add a subwoofer to reinforce low frequencies
or to output low bass sound from the subwoofer channel when
reproducing discrete signals.
Connect the SUBWOOFER OUTPUT terminal of this unit to
the input terminal of the subwoofer amplifier, and connect the
speaker terminals of the subwoofer amplifier to the subwoofer.
With some subwoofers, including the Yamaha Active Servo
Processing Subwoofer System, the amplifier and subwoofer
are in the same unit.
11
English
How to Connect:
Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are
faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and –
markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.
Caution
Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or
speakers.
To connect to the MAIN SPEAKERS terminals
Red: positive (+)
Black: negative (–)
1 Unscrew the knob.
2 Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
3 Tighten the knob and
secure the wire.
To connect to the REAR and CENTER SPEAKERS
terminals
Red: positive (+)
Black: negative (–)
1 Press the tab.
2 Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
3 Release the tab and
secure the wire.
<U.S.A., Canada, Australia, China and General models
only>
Banana Plug connections are also possible. Simply insert the
Banana Plug connector into the corresponding terminal.
1
2
3
2
3
1
12
SUBWOOFER OUTPUT terminal
This terminal is for connecting to the input terminal of an
amplifier driving a subwoofer.
This terminal outputs low frequencies from the main and center
channels. (The cut-off frequency of signals output from this
terminal is 150 Hz.)
When 6 channel discrete signals are input to this unit and are
selected as the input source, this terminal outputs signals from
the subwoofer channel.
OUTPUT
SUB
WOOFER
IMPEDANCE SELECTOR switch
Be sure to switch this only when the power to this unit is not
on.
Select the position whose requirements your speaker system
meets.
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/
ON SWITCH IS PRESSED, the IMPEDANCE SELECTOR
switch may not be set to either end closely. If so, set the
switch to either end closely.
<General model>
IMPEDANCE SELECTOR
A OR B
: 4
Ω
MIN. /SPEAKER
A B
: 8
Ω
MIN. /SPEAKER
:
6
Ω
MIN. /SPEAKER
:
6
Ω
MIN. /SPEAKER
A OR B
: 8
Ω
MIN. /SPEAKER
A B
:
16
Ω
MIN. /SPEAKER
:
8
Ω
MIN. /SPEAKER
:
8
Ω
MIN. /SPEAKER
AC OUTLETS
MAIN
CENTER
REAR
MAIN
CENTER
REAR
I00W MAX. TOTAL
SWITCHED
SET BEFORE POWER ON
IMPEDANCE SELECTOR
VOLTAGE SELECTOR
(Left position)
Main: If you use one pair of main speakers, the impedance
of each speaker must be 4Ω or higher.
If you use two pairs of main speakers, the impedance
of each speaker must be 8Ω or higher.
Center: The impedance of the speaker must be 6Ω or higher.
Rear: The impedance of each speaker must be 6Ω or
higher.
(Right position)
Main: <Except for Canada model>
If you use one pair of main speakers, the impedance
of each speaker must be 8Ω or higher.
If you use two pairs of main speakers, the impedance
of each speaker must be 16Ω or higher.
<Canada model only>
The impedance of each speaker must be 8Ω or
higher.
Center: The impedance of the speaker must be 8Ω or higher.
Rear: The impedance of each speaker must be 8Ω or
higher.
13
English
ANTENNA CONNECTIONS
● Each antenna should be connected to the designated terminals correctly, referring to the following diagram.
● Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor
reception quality, an outdoor antenna may result in improvement.
Outdoor FM antenna
75-ohm/300-ohm
antenna adapter
75-ohm coaxial cable
75-ohm/300-ohm
antenna adapter
300-ohm feeder
Ground
Indoor FM
antenna
(included)
Outdoor AM antenna
AM loop
antenna
(included)
FM
ANT
AM
ANT
GND
75Ω
UNBAL.
Connecting the AM loop antenna
12 3
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
Orient so that the best
reception is obtained.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is a
metal stake driven into moist earth.
Notes
● When connecting the indoor FM
antenna, insert its connector into
the FM ANT terminal firmly.
● If you need an outdoor
FM antenna to improve
FM reception quality, either
300-ohm feeder or coaxial cable
may be used. In locations
troubled by electrical interference, coaxial cable is
preferable.
14
CONTROLS AND THEIR FUNCTIONS
FRONT PANEL
~ STANDBY/ON switch
Press this switch to turn the power to this unit on. Press it
again to put this unit in the standby mode.
In STANDBY, this unit consumes a very small quantity of
power to receive infrared signals from the remote control
transmitter.
Ÿ Remote control sensor
Receives signals from the remote control transmitter.
! Display panel
Shows various information. (Refer to page 18.)
⁄ MEMORY (MAN’L/AUTO FM) button
Press this button to preset AM and FM radio frequencies
manually. (Refer to page 27.)
When this button is pressed and held for more than 3 seconds,
automatic preset tuning begins. (Refer to page 28.)
@ EDIT button
This button is used to exchange the places of two preset
stations with each other. (Refer to page 29.)
¤ TUNING MODE (AUTO/MAN’L MONO) button
Press this button to switch the tuning mode to automatic or
manual. To select the automatic tuning mode, press this button
so that the AUTO indicator lights up on the display. To select
the manual tuning mode, press this button so that the AUTO
indicator goes off. (Refer to page 26.)
# FM/AM button
Press this button to switch the reception band to FM or AM.
(Refer to page 26.)
‹ Input selector buttons
Select a program source to listen to or watch. When a button is
pressed, the name of selected source appears on the display.
When either the TV/DBS or DVD/LD input source is selected,
pressing the same selector button repeatedly switches the
input signals between 2 channel stereo signals and 6 channel
discrete signals. When switched to “6ch”, discrete signals from
the unit connected to the 6CH DISCRETE INPUT terminals of
this unit are selected as the input signals.
$ VOLUME control
Use to raise or lower the volume level.
BASS TREBLE BALANCE
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
LR55
4
3
2
l
0
l
2
3
4
VOLUME
l6
20
28
40
60
l2
8
4
2
0
–dB
SPEAKERS
PHONES
A
ON
B
OFF
A
/
B
/
C
/
D
/
E
1
2
3
4
567
8
STANDBY/ON
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO MOVIE
CENTER MODE
DISCO
CONCERT
HALL
ROCK
CONCERT
EFFECT
TV SPORTS
DELAY/CENTER/
REAR/SWFR
TUNING
UPDOWN
TIME
/
LEVEL
FM
/
AM
MAN'L
/
AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
MEMORY
EDIT
VCR
TV
/
DBS
TAPE/MD
MONITOR
2CH/6CH
TUNER
CD
PHONO
2CH/6CH
DVD/LD
NATURAL SOUND AV RECEIVER
~
›
%
fi
^
fl
Ÿ
$
&
‹
@¤
#
(*
‡
°
⁄
·
!
15
English
PHONES
› PHONES jack
To listen with headphones, connect the headphones to the
PHONES jack. The sound output from the PHONES jack is the
same as that from the main speakers.
When listening with headphones privately, set both the
SPEAKERS A and B switches to the OFF position and switch
off the digital sound field processor (so that no DSP program
indicator is lit in the display) by pressing the EFFECT button.
% SPEAKERS switches
Set the switch A or B (or both A and B) for the main speaker
system (connected to this unit) you will use to the ON position.
Set the switch for the main speaker system you will not use to
the OFF position. (Refer to page 25.)
fi A/B/C/D/E button
Press this button to select a desired group (A–E) of preset
stations. (Refer to page 27.)
^ Preset station number selector buttons
Press to select a preset station number (1 to 8). (Refer to page
27.)
fl Tone controls
These controls are effective only for the sound from the main
speakers. (Refer to page 25.)
BASS
Used to increase or decrease the low frequency response.
The 0 position produces flat response.
TREBLE
Used to increase or decrease the high frequency response.
The 0 position produces flat response.
& BALANCE control
This control is effective only for the sound from the main
speakers.
Adjusts the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions. (Refer to page
25.)
‡ TUNING DOWN/UP button
Use for tuning radio stations. Press the UP side to tune in to
higher frequencies, and press the DOWN side to tune in to
lower frequencies.
* DSP program selector buttons
Select a DSP program. When a button is pressed, the name of
selected program lights up on the display. (Refer to page 36.)
° EFFECT button
Switches the digital sound field processor on and off (including
the Dolby Pro Logic Surround decoder). (Refer to page 37.)
( CENTER MODE button
Selects a center channel output mode (NORMAL, WIDE or
PHANTOM). (Refer to page 20.)
· DELAY/CENTER/REAR/SWFR and TIME/LEVEL +/–
buttons
Adjust the delay time (DELAY), the center channel output level
(CENTER), the rear channel output level (REAR) and the
output level to the SUBWOOFER OUTPUT terminal (SWFR).
Select the item which you want to adjust by pressing the
DELAY/CENTER/REAR/SWFR button and adjust its time or
level by pressing the TIME/LEVEL +/– button. (Refer to pages
25, 38, and 39.)
16
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit as well
as the components connected to it. The remote control transmitter is factory set to control this unit and most Yamaha components.
To set up the remote control transmitter to control the components of other manufacturers, refer to “SETUP CODES” on page 41.
6CH
2CH
17
English
~ Component selector
Press the button for the component you want to control with the
remote control transmitter. (The proper code must be set for
your component. See “SETUP CODES” on page 41.)
When the component selector has been pressed, the remote
control transmitter is set to operate that component.
Ÿ POWER /I
When you have preset the code for a YAMAHA component, this
button switches between the power on and standby mode.
When you have preset the code for another manufacturer’s
component, this button turns on that component if it has a
remote control transmitter with a power button.
* Functions only when the component selector button
AMP<TUNER>, TAPE/MD, CD, DVD/LD or DVD MENU has
been pressed.
! TEST
Press this button to output the test tone for each speaker.
* Functions only when the component selector button
AMP<TUNER> has been pressed.
⁄ MUTE
Press this button to mute the sound.
@ VOLUME
These buttons are used to adjust the volume.
: Turns up the volume.
: Turns down the volume.
¤ SLEEP
This button is used to set the SLEEP timer.
# PRG+, PRG–
These buttons are used to select a DSP program.
* Function only when the component selector button
AMP<TUNER> has been pressed.
‹ Indicator
This flashes in red when a button on the remote control
transmitter is pressed. When it flashes rapidly several times,
press the selected button again.
$ Input selector (1 to 7)
1)
/ Numeric buttons
2)
1) These buttons are used to select the program source to be
played.
* Function only when the component selector button
AMP<TUNER>, TAPE/MD, CD or DVD/LD has been
pressed.
2) These buttons are used to select the menu or channel.
* Function only when the component selector button DVD
MENU, VCR, CBL/DBS or TV has been pressed.
› EFFECT
1)
/ CLEAR
2)
/ +100
3)
1) This button is used to switch the DSP program on or off.
* Functions only when AMP<TUNER>, TAPE/MD, CD,
DVD/LD, VCR or TV on the component selector has been
pressed.
2) This button is used to clear the settings.
* Functions only when the component selector button DVD
MENU has been pressed.
3) This button is used to select the channel.
* Functions only when the component selector button CBL/
DBS has been pressed.
% ENTER
1)
/ +10
2)
/ A/B/C/D/E
3)
1) This button is used to enter the channel.
* Functions only when the component selector button VCR,
CBL/DBS or TV has been pressed.
2) This button is used to select the menu.
* Functions only when the component selector button DVD
MENU has been pressed.
3) This button is used to select a group of presets.
* Functions only when the component selector button AMP
<TUNER> has been pressed.
fi DISC SKIP +/–
1)
/ CH +/–
2)
/ PRESET +/–
3)
1) These buttons are used to skip to the next or previous disc.
* Function only when the component selector button CD,
DVD/LD or DVD MENU has been pressed.
2) These buttons are used to select the next or previous
channel.
* Function only when the component selector button VCR,
CBL/DBS or TV has been pressed.
3) These buttons are used to select a preset station.
* Functions only when the component selector button AMP
<TUNER> has been pressed.
^ Operation buttons
1)
/ Setup buttons
2)
1) These buttons function as play, stop, skip, etc. for operating
the component.
* Function only when the component selector button TAPE/
MD, CD, DVD/LD, VCR or TV has been pressed.
2) These buttons are for adjusting various settings.
* Function only when the component selector button DVD
MENU or CBL/DBS has been pressed.
18
DISPLAY PANEL
~ Multi-information display
Displays various information, for example station frequency,
preset station number and name of selected input source.
Ÿ STEREO indicator
Lights up when an FM stereo broadcast with sufficient signal
strength is received.
! Signal-level meter
Indicates the signal level of the received station.
If multipath interference is detected, the indication decreases.
⁄ SLEEP indicator
Lights up while the built-in SLEEP timer is functioning.
@ Center channel mode indicators
The name of a selected center channel mode lights up only
when a program which uses Dolby Pro Logic Surround is
selected.
¤ EFFECT OFF indicator
Lights up if neither the digital sound field processor nor the
Dolby Pro Logic Surround decoder is on. In this state, sound
output is 2-channel stereo.
# MEMORY indicator
When the MEMORY button is pressed, this indicator flashes for
about 5 seconds. During this period, the displayed station can
be programmed to the memory by using the A/B/C/D/E button
and the preset station number selector buttons.
‹ AUTO indicator
Lights up when this unit is in the automatic tuning mode.
$ TAPE MON indicator
Lights up when the tape deck (or MD recorder, etc.) is selected
as the input source by pressing the TAPE/MD MONITOR
button.
› DSP program indicators
The name of a selected DSP program lights up when the built-
in digital sound field processor or the Dolby Pro Logic Surround
decoder is on.
PRESET
kHz
MHz
MEMORY
AUTO
SLEEP
TAPE MON
STEREO
0
20
l00
ms dB
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
TV SPORTS
DISCO
ROCK CONCERT
CONCERT HALL
NORM
WIDE
PHANTOM
EFFECT OFF
~Ÿ
@¤
›$#
‹
⁄
!
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
Yamaha RX-V395 Инструкция по применению
- Категория
- Ресиверы
- Тип
- Инструкция по применению
- Это руководство также подходит для
Задайте вопрос, и я найду ответ в документе
Поиск информации в документе стал проще с помощью ИИ
на других языках
- English: Yamaha RX-V395 Owner's manual
- français: Yamaha RX-V395 Le manuel du propriétaire
- italiano: Yamaha RX-V395 Manuale del proprietario
- español: Yamaha RX-V395 El manual del propietario
- Deutsch: Yamaha RX-V395 Bedienungsanleitung
- Nederlands: Yamaha RX-V395 de handleiding
- português: Yamaha RX-V395 Manual do proprietário
- dansk: Yamaha RX-V395 Brugervejledning
- polski: Yamaha RX-V395 Instrukcja obsługi
- čeština: Yamaha RX-V395 Návod k obsluze
- Türkçe: Yamaha RX-V395 El kitabı
- suomi: Yamaha RX-V395 Omistajan opas
- română: Yamaha RX-V395 Manualul proprietarului
Похожие модели бренда
-
Yamaha DSP-E492 Руководство пользователя
-
-
-
-
-
-
-
-
-