Sony DSC-TX10 Silver Руководство пользователя

4-265-636-41(1)

DSC-TX10

Digital Still Camera / Instruction Manual GB

Цифровой фотоаппарат / Инструкция по эксплуатации

RU

Цифровий фотоапарат / Посібник з експлуатації UA

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Left

GB

2

Owner’s Record

The model and serial numbers are located on the bottom. Record the serial number in the

space provided below. Refer to these numbers whenever you call your Sony dealer

regarding this product.

Model No. DSC-TX10

Serial No. ______________________________

Model No. AC-UB10/UB10B

Serial No. ______________________________

To reduce fire or shock hazard, do not expose the unit to rain or

moisture.

IMPORTANT SAFETY INSTRUCTIONS

-SAVE THESE INSTRUCTIONS

DANGER

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, CAREFULLY FOLLOW THESE

INSTRUCTIONS

If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the

proper configuration for the power outlet.

[ Battery pack

If the battery pack is mishandled, the battery pack can burst, cause a fire or even chemical

burns. Observe the following cautions.

• Do not disassemble.

• Do not crush and do not expose the battery pack to any shock or force such as

hammering, dropping or stepping on it.

• Do not short circuit and do not allow metal objects to come into contact with the battery

terminals.

• Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a

car parked in the sun.

• Do not incinerate or dispose of in fire.

English

WARNING

CAUTION

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Right

GB

3

GB

• Do not handle damaged or leaking lithium ion batteries.

• Be sure to charge the battery pack using a genuine Sony battery charger or a device that

can charge the battery pack.

• Keep the battery pack out of the reach of small children.

• Keep the battery pack dry.

• Replace only with the same or equivalent type recommended by Sony.

• Dispose of used battery packs promptly as described in the instructions.

[ AC Adaptor

Connect the AC Adaptor to the nearest wall outlet (wall socket).

If some trouble occurs while using the AC Adaptor, immediately shut off the power by

disconnecting the plug from the wall outlet (wall socket).

The power cord (mains lead), if supplied, is designed specifically for use with this camera

only, and should not be used with other electrical equipment.

[ RECYCLING LITHIUM-ION BATTERIES

Lithium-Ion batteries are recyclable.

You can help preserve our environment by returning your used

rechargeable batteries to the collection and recycling location nearest

you.

For more information regarding recycling of rechargeable batteries,

call toll free

1-800-822-8837, or visit http://www.rbrc.org/

Caution: Do not handle damaged or leaking Lithium-Ion batteries.

[ Battery pack

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

UL is an internationally recognized safety organization.

The UL Mark on the product means it has been UL Listed.

If you have any questions about this product, you may call:

Sony Customer Information Center

1-800-222-SONY (7669).

The number below is for the FCC related matters only.

For Customers in the U.S.A. and Canada

For Customers in the U.S.A.

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Left

GB

4

[ Regulatory Information

[ CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual

could void your authority to operate this equipment.

[ Note:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

The supplied interface cable must be used with the equipment in order to comply with the

limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

Declaration of Conformity

Trade Name: SONY

Model No.: DSC-TX10

Responsible Party: Sony Electronics Inc.

Address: 16530 Via Esprillo,

San Diego, CA 92127 U.S.A.

Telephone No.: 858-942-2230

This device complies with Part15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Right

GB

5

GB

[ Notice for the customers in the countries applying EU Directives

The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo,

108-0075 Japan. The Authorized Representative for EMC and product safety is Sony

Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or

guarantee matters please refer to the addresses given in separate service or guarantee

documents.

This product has been tested and found compliant with the limits set out in the EMC

Directive for using connection cables shorter than 3 meters (9.8 feet).

[ Attention

The electromagnetic fields at the specific frequencies may influence the picture and sound

of this unit.

[ Notice

If static electricity or electromagnetism causes data transfer to discontinue midway (fail),

restart the application or disconnect and connect the communication cable (USB, etc.)

again.

[ Disposal of Old Electrical & Electronic Equipment (Applicable in

the European Union and other European countries with separate

collection systems)

This symbol on the product or on its packaging indicates that this product

shall not be treated as household waste. Instead it shall be handed over to

the applicable collection point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling

of this product. The recycling of materials will help to conserve natural

resources. For more detailed information about recycling of this product,

please contact your local Civic Office, your household waste disposal service or the shop

where you purchased the product.

For Customers in Europe

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Left

GB

6

[ Disposal of waste batteries (applicable in the European Union

and other European countries with separate collection systems)

This symbol on the battery or on the packaging indicates that the battery

provided with this product shall not be treated as household waste.

On certain batteries this symbol might be used in combination with a

chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are

added if the battery contains more than 0.0005% mercury or 0.004% lead.

By ensuring these batteries are disposed of correctly, you will help prevent

potentially negative consequences for the environment and human health which could

otherwise be caused by inappropriate waste handling of the battery. The recycling of the

materials will help to conserve natural resources.

In case of products that for safety, performance or data integrity reasons require a

permanent connection with an incorporated battery, this battery should be replaced by

qualified service staff only. To ensure that the battery will be treated properly, hand over

the product at end-of-life to the applicable collection point for the recycling of electrical

and electronic equipment.

For all other batteries, please view the section on how to remove the battery from the

product safely.

Hand the battery over to the applicable collection point for the recycling of waste batteries.

For more detailed information about recycling of this product or battery, please contact

your local Civic Office, your household waste disposal service or the shop where you

purchased the product.

A moulded plug complying with BS 1363 is fitted to this equipment for your safety and

convenience.

Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the

supplied one and approved by ASTA or BSI to BS 1362, (i.e., marked with an or

mark) must be used.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the

fuse cover after you change the fuse. Never use the plug without the fuse cover. If you

should lose the fuse cover, please contact your nearest Sony service station.

Notice for customers in the United Kingdom

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Right

GB

7

GB

About water-proof, dust-proof, and shock-proof

performance of the camera

This camera is equipped to be water-proof, dust-proof and shock-proof.

Damage caused from misuse, abuse or failure to properly maintain the camera

is not covered by the limited warranty.

• This camera is water-proof/dust-proof equivalent to IEC60529 IP58. The

camera is operable up to a water depth of 5 m for 60 minutes.

• Do not subject the camera to pressurized water, such as from a tap.

• Do not use in hot springs.

• Use the camera in the recommended operating water temperature range of

–10°C to +40°C (14°F to 104°F).

• Conforming to MIL-STD 810F Method 516.5-Shock standards, this product

has passed testing when dropped from a height of 1.5 m above a 5-cm thick

plywood board

*

.

*Depending on use conditions and circumstances, no guarantee is made regarding

damage to, malfunction of, or the water-proof performance of this camera.

• As for dust-proof/shock-proof performance, there is no guarantee that the

camera will not become scratched or dented.

• Sometimes water-proof performance is lost if the camera is subjected to a

strong shock such as from being dropped. We recommend the camera be

inspected at an authorized repair shop for a fee.

• Accessories supplied do not meet water-proof, dust-proof, and shock-proof

specifications.

Notes before using the camera under/near water

• Make sure that no foreign matter such as

sand, hair, or dirt gets inside the battery/

memory card cover or multi-connector

cover. Even a small amount of foreign

matter may lead to water entering the

camera.

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Left

GB

8

• Confirm that the sealing gasket and its

mating surfaces have not become scratched.

Even a small scratch may lead to water

entering the camera. If the sealing gasket or

its mating surfaces become scratched, take

the camera to an authorized repair shop to

have the sealing gasket replaced for a fee.

• If dirt or sand gets on the sealing gasket or

its mating surfaces, wipe the area clean with

a soft cloth that will not leave behind any

fibers. Do not use a sharp-pointed implement to prevent the sealing gasket

and its mating surfaces from becoming scratched.

• Do not open/close the battery/memory card cover or multi-connector cover

with wet or sandy hands or near water. There is a risk this will lead to sand or

water getting inside. Before opening the cover, perform the procedure

described in “Cleaning after using the camera under/near water”.

• Open the battery/memory card cover and multi-connector cover with the

camera completely dry.

• Always confirm that the battery/memory card cover and multi-connector

cover have been securely locked.

Notes on using the camera under/near water

• The touch panel may be activated by water splashes on the screen icons.

When using the camera under/near water, it is recommended that you hide

the icons by touching on the right side of the screen. Touch for a few

seconds to display the icons again.

• The touch panel cannot be operated underwater. Use the buttons of the

camera to perform shooting or playback operations.

• Do not subject the camera to shock such as from jumping into water.

• Do not open and close the battery/memory card cover or multi-connector

cover while under/near water.

• Use a separately available housing (Marine Pack) if going more than

5 meters under water.

• This camera sinks in water. Place your hand through the wrist strap to

prevent the camera from sinking.

• Faint, white, circular spots may appear in under-water flash photos due to

reflections off of floating objects. This is not a malfunction.

• Select (Underwater) in Scene Selection to shoot underwater with less

distortion.

• If water drops or other foreign matter is present on the lens, you will be

unable to record clear images.

1 Sealing gasket

2 Surface contacting the

sealing gasket

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Right

GB

9

GB

• Do not open the lens cover where the sand is whirling.

Cleaning after using the camera under/near

water

• Always clean the camera with water after use

within 60 minutes, and do not open the battery/

memory card cover before cleaning is finished.

Sand or water may get inside places where it

cannot be seen. If not rinsed, water-proof

performance will be degraded.

• Allow the camera to sit in pure water poured into a cleaning bowl for about 5

minutes. Then, gently shake the camera, press each button, slide the zoom

lever or the lens cover inside the water, to clean away any salt, sand or other

matter lodged around the buttons or the lens cover.

• After rinsing, wipe away water drops with a soft cloth. Allow the camera to

dry completely in a shady location with good ventilation. Do not blow dry

with a hair dryer as there is a risk of deformation and/or degraded water-

proof performance.

• This camera is constructed to drain water. Water will drain from openings

around the ON/OFF (Power) button, zoom lever, and other controls. After

removing from water, place the camera on a dry cloth for a while to allow

water to drain.

• Bubbles may appear when the camera is placed under water. This is not a

malfunction.

• The camera body may become discolored if it comes in contact with

sunscreen or suntan oil. If the camera does come in contact with sunscreen or

suntan oil, quickly wipe it clean.

• Do not allow the camera to sit with salt water inside or on the surface. This

may lead to corrosion or discoloration, and degradation of water-proof

performance.

• To maintain the water-proof performance, we recommend that once a year

you take the camera to your dealer, or to an authorized repair shop, to have

the sealing gasket of the battery/memory card cover, or of the multi-

connector cover replaced for a fee.

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Left

GB

10

For details on advanced operations, please read “Cyber-shot User Guide”

(HTML) on the CD-ROM (supplied) using a computer.

For Windows users:

1 Click [User Guide] t [Install].

2 Start “User Guide” from the shortcut on the desktop.

For Macintosh users:

1 Select the [User Guide] folder and copy [eng] folder stored in [User Guide]

folder to your computer.

2 After copying is complete, double-click “index.html” in [eng] folder.

• Camera (1)

• Rechargeable battery pack NP-BN1 (1)

• Multi-use terminal USB cable (1)

• AC Adaptor AC-UB10/UB10B (1)

• Power cord (mains lead) (not supplied in the USA and Canada) (1)

• Paint pen (1)

• Wrist strap (1)

•CD-ROM (1)

– Cyber-shot application software

– “Cyber-shot User Guide”

• Instruction Manual (this manual) (1)

• Notes on the water-proofing (1)

Refer to “Cyber-shot User Guide” (HTML) on

supplied CD-ROM

Checking the supplied items

Insert the CD-ROM into the CD-ROM drive.

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Right_2 column

GB

11

GB

A Microphone

B Lens cover

C Flash

D Self-timer lamp/Smile Shutter

lamp/AF illuminator

E Lens

F (Playback) button

G MOVIE (Movie) button

H Screen/Touch panel

I ON/OFF (Power/Charge) button

J ON/OFF (Power/Charge) lamp

K Shutter button

L For shooting: W/T (Zoom) lever

For viewing: (Playback

zoom) lever/ (Index) lever

M Hook for wrist strap

N HDMI connector

O Multi connector (Type3b)

P Memory card slot

Q Access lamp

R Battery eject lever

S Connector cover

T Battery/memory card cover

U (TransferJet™) mark

V Battery insertion slot

W Tripod receptacle

• Use a tripod with a screw less

than 5.5 mm (7/32 inches) long.

Otherwise, you cannot firmly

secure the camera, and damage to

the camera may occur.

Identifying parts

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Left

GB

12

Inserting the battery pack

1

Open the cover.

2

Insert the battery pack.

• While pressing the battery eject lever, insert the battery pack as

illustrated. Make sure that the battery eject lever locks after insertion.

Charging the battery pack

Eject lever

Power cord

(Mains lead)

For customers in the USA,

Canada

For customers in countries/regions

other than the USA and Canada

Power/Charge lamp

Lit: Charging

Off: Charging finished

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Right

GB

13

GB

• Close the cover securely, so that the yellow mark under the slide lock is hidden.

• When the Power/Charge lamp on the camera does not lit even if the AC Adaptor is

connected to the camera and the wall outlet (wall socket), it indicates that the

charging stops temporarily on standby. The charging stops and enters the standby

status automatically when the temperature is outside of the recommended

operating temperature. When the temperature gets back within the appropriate

range, the charging resumes. We recommend charging the battery pack in an

ambient temperature of between 10°C to 30°C (50ºF to 86ºF).

• Connect the AC Adaptor (supplied) to the nearest wall outlet (wall socket). If any

malfunctions occur while using the AC Adaptor, disconnect the plug from the wall

outlet (wall socket) immediately to disconnect the power source.

• When charging is finished, disconnect the AC Adaptor from the wall outlet (wall

socket).

• Be sure to use only genuine Sony brand battery packs, multi-use terminal USB

cable (supplied) and AC Adaptor (supplied).

x

Charging by connecting to a computer

The battery pack can be charged by connecting the camera to a computer using

a multi-use terminal USB cable.

1

Open the connector cover and connect the camera and

the AC Adaptor (supplied), using the multi-use terminal

USB cable (supplied).

2

Connect the AC Adaptor to the wall outlet (wall socket).

The Power/Charge lamp lights orange, and charging starts.

• Turn off the camera while charging the battery.

• You can charge the battery pack even when it is partially charged.

Notes

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Left

GB

14

• Note the following points when charging via a computer:

– If the camera is connected to a laptop computer that is not connected to a power

source, the laptop battery level decreases. Do not charge for an extended period

of time.

– Do not turn on/off or restart the computer, or wake the computer resume from

sleep mode when a USB connection has been established between the computer

and the camera. The camera may cause a malfunction. Before turning on/off, or

restarting the computer or waking the computer from sleep mode, disconnect the

camera and the computer.

– No guarantees are made for charging using a custom-built computer or a

modified computer.

x

Charging time

The charging time is approximately 210 min. using the AC Adaptor

(supplied).

• The above charging time applies when charging a fully depleted battery pack at a

temperature of 25°C (77°F). Charging may take longer depending on conditions of

use and circumstances.

x

Battery life and number of still images you can record

and view

• The above number of still images applies when the battery pack is fully charged.

The number of still images may decrease depending on the conditions of use.

• The number of still images that can be recorded is for shooting under the following

conditions:

– Using Sony “Memory Stick PRO Duo” (Mark2) media (sold separately)

– The battery pack is used at an ambient temperature of 25°C (77°F).

• The number for “Shooting (still images)” is based on the CIPA standard, and is for

shooting under the following conditions:

(CIPA: Camera & Imaging Products Association)

– [Panel Brightness] is set to [3]

Note

Battery life Number of images

Shooting (still images) Approx. 125 min. Approx. 250 images

Viewing (still images) Approx. 190 min. Approx. 3800 images

Shooting (movies) Approx. 60 min. —

Notes

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Right

GB

15

GB

– Shooting once every 30 seconds.

– The zoom is switched alternately between the W and T ends.

– The flash strobes once every two times.

– The power turns on and off once every ten times.

• The battery life for movies applies shooting under the following conditions:

– Movie quality: AVCHD HQ

– When continuous shooting ends because of set limits (page 24), press the

MOVIE (Movie) button again and continue shooting. Shooting functions such as

the zoom do not operate.

x

Feeding power

The camera can be supplied with power from the wall outlet (wall socket) by

connecting to the AC Adaptor, using the multi-use terminal USB cable

(supplied).

You can import images to a computer without worrying about wearing down

the battery pack by connecting the camera to a computer using the multi-use

terminal USB cable.

• Power cannot be supplied when the battery pack is not inserted in the camera.

• Power supply from the wall outlet (wall socket) is available only when the camera

is in playback mode or when a connection is made between the camera and a

computer. If the camera is in shooting mode or while you are changing the settings

of the camera, power is not supplied even if you make a USB connection using the

multi-use terminal USB cable.

• If you connect the camera and a computer using the multi-use terminal USB cable

when the camera is in playback mode, the display on the camera is changed from

the playback screen to the USB connection screen. Press (Playback) button to

switch to the playback screen.

Notes

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Left

GB

16

x

Memory cards that you can use

• In this manual, products in A are collectively referred to as “Memory Stick Duo”

media, and products in B are collectively referred to as SD card.

Inserting a memory card (sold separately)

1

Open the cover.

2

Insert the memory card (sold separately).

• With the notched corner facing as illustrated, insert the memory card

until it clicks into place.

3

Close the cover securely, so that the yellow mark under

the slide lock is hidden.

• Closing the cover with the battery inserted incorrectly may damage the

camera.

Memory card For still images For movies

A

Memory Stick PRO Duo aa (Mark2 only)

Memory Stick PRO-HG Duo aa

Memory Stick Duo a —

B

SD memory card aa (Class 4 or faster)

SDHC memory card aa (Class 4 or faster)

SDXC memory card aa (Class 4 or faster)

Ensure the notched corner faces

correctly.

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Right

GB

17

GB

x

To remove the memory card/battery pack

Memory card: Push the memory card in once.

Battery pack: Slide the battery eject lever. Be sure not to drop the battery pack.

• Never remove the memory card/battery pack when the access lamp (page 11) is lit.

This may cause damage to data in the memory card/internal memory.

Note

Setting the clock

1

Lower the lens cover.

The camera is turned on. The power lamp lights up only when the camera

starts up.

• You can also turn on the camera by pressing the ON/OFF (Power)

button.

• It may take time for the power to turn on and allow operation.

2

Select a desired language.

3

Select the desired area following the instructions on the

screen, then touch [Next].

4

Set [Daylight Savings] or [Summer Time], [Date & Time

Format] and [Date & Time], then touch [Next].

• Midnight is indicated as 12:00 AM, and noon as 12:00 PM.

5

Touch [OK].

Lens coverON/OFF (Power)

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Left

GB

18

Shooting still images

Shooting movies

6

Select the desired display color, following the

instructions on the screen, then touch [OK].

7

When an [In-Camera Guide] introductory message is

appeared on the screen, touch [OK].

8

Read the waterproof precautions, then touch [OK].

Shooting still images/movies

1

Press the shutter button halfway down to focus.

When the image is in focus, a beep sounds and the z indicator lights.

2

Press the shutter button fully down.

1

Press the MOVIE (Movie) button to start recording.

• Use the W/T (zoom) lever to change the zoom scale.

2

Press the MOVIE button again to stop recording.

Shutter button

MOVIE (Movie) button

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Right

GB

19

GB

• The sound of the lens and lever operating will be recorded when the zoom function

operates while shooting a movie. The sound of the MOVIE button operating may

also be recorded when movie recording is finished.

• Continuous shooting is possible for approximately 29 minutes at one time at the

camera’s default settings and when the temperature is approximately 25°C (77°F).

When movie recording is finished, you can restart recording by pressing the

MOVIE button again. Recording may stop to protect the camera depending on the

ambient temperature.

x

Selecting next/previous image

Touch (Next)/ (Previous) on the screen.

• To play back movies, touch (Playback) in the center of the screen.

• To zoom in, touch the still image being played back.

x

Deleting an image

1 Touch (Delete) t [This Image].

x

Returning to shooting images

Touch on the screen.

• You can also return to shooting mode by pressing the shutter button halfwaydown.

Notes

Viewing images

1

Press the (Playback) button.

• When images on a memory card recorded with other cameras are played

back on this camera, the registration screen for the data file appears.

(Playback)

DSC-TX10

4-265-636-41(1)

F:\@Sagyou\1229\4265636411CEE2\4265636411DSCTX

10CEE2\01GB\010GB1.fm

master:Left

GB

20

This camera contains an internal function guide. This allows you to search the

camera’s functions according to your needs.

In-Camera Guide

1

Touch (In-Camera Guide).

• The mark will appear on the bottom right of the screen while viewing.

2

Select a search method from [In-Camera Guide].

Shoot/playback guide: Search for various operation functions in

shooting/viewing mode.

Icon guide: Search the function and meaning of displayed icons.

Troubleshooting: Search common problems and their solution.

Objective guide: Search functions according to your needs.

Keyword: Search functions by key words.

History: Display the last 10 items displayed in [In-Camera Guide].

Страница загружается ...

Sony DSC-TX10 Silver Руководство пользователя

Это руководство также подходит для

Sony DSC-TX10 Silver Руководство пользователя

Похожие модели бренда