Yamaha V1 Руководство пользователя

Бренд: Yamaha

Модель: V1

Тип: Руководство пользователя

Это руководство также подходит для

PM5D system software V1.12 includes the following changes and additions relative to V1.04 (changes up to V1.10 are also included).

Use ENCODER [ON] keys to turn phan-

tom power (+48V) on/off (from V1.05)

A “USE ENCODER-ON AS +48V” option has been added

to the PREFERENCE 1 screen. If this option is on, and HA

(head amp input sensitivity) is selected as the encoder

mode, you can use the ENCODER [ON] key located above

each encoder to turn phantom power supply (+48V) on/off.

Switch parameter value indication on/

off in the Name display (from V1.05)

A “CHANNEL NAME NUMERIC DISPLAY” field has been

added to the PREFERENCE 2 screen. In V1.04 and earlier,

operating the fader or encoder (pan setting) of each chan-

nel caused the name display to show the value of that

parameter. In V1.05 and later, turning the “ENCODER

VALUE” and “FADER VALUE” options off will prevent the

respective parameter value from appearing when you oper-

ate the fader or encoder.

Select the monitor source from the

panel (from V1.05)

When selecting a monitor source from the panel in V1.04 or

earlier, you could simultaneously select one source from

[2TR A1]–[2TR D3] or [DEFINE] and one source from

[STEREO A]/[STEREO B] (including LCR), for a maxi-

mum total of two sources. In V1.05 and later, turning on

one key will turn off the other keys, allowing you to select a

single monitor source more rapidly. If you want to select

two sources simultaneously (as in V1.04 and earlier), press

the corresponding panel keys simultaneously, or use the

MONITOR screen.

HA follows Recall Safe on/off operations

(from V1.05)

A new SAFE KEY MODE SELECT section has been added

to the RECALL SAFE screen. If you turn on the HA+CH

button, using the [RECALL SAFE] key of the panel or the

RECALL SAFE button in the CH VIEW screen (INPUT

VIEW function) to turn Recall Safe on/off will now also

turn on/off the Recall Safe setting for the HA patched to the

corresponding channel. If the CH button is on, the HA

Recall Safe setting will not be linked.

DCA group name Recall Safe and Selec-

tive Recall can be switched on/off (from

V1.05)

A new WITH NAME button has been added to the DCA

area of the RECALL SAFE screen and SELECTIVE RECALL

screen. This allows you to exclude just the DCA group name

from DCA group Recall Safe and Selective Recall. If the

WITH NAME button is on, Recall Safe and Selective Recall

will apply to the DCA group names of DCA groups for

which these functions are on. If the WITH NAME button is

off, DCA group names are excluded from Recall Safe and

Selective Recall.

PM5D V1.12 Supplementary Manual

PM5DV112E Page 1 Monday, December 27, 2004 11:17 AM

Parameter operation for Recall Safe/

Selective Recall (from V1.12)

When using Recall Safe or Selective Recall, there has been a

change in the behavior of parameters of which only one

exists for each pair of adjacent odd-numbered/even-num-

bered channels or modules (see owner's manual p.165). If

Recall Safe or Selective Recall is specified for only one of

these channels or modules, the parameters will behave as

follows.

• PAIR

Forcibly turned off (pairing will be defeated).

• GATE STEREO LINK

• COMP STEREO LINK

• GEQ LINK

LINK parameters will be forcibly turned off (link will be

defeated).

• DELAY GANG

• ATT GANG

GANG parameters will be recalled. If GANG turns On

because of the recall, the relative differences of the

DELAY and ATT parameter values following the recall

will be maintained when they are edited.

• MS DECODE

• FIXED/VARI

These will not be recalled.

• PAN MODE

The PAN MODE parameter will be recalled. However, if

the recall would cause the PAN MODE setting to change

from BALANCE to some other setting, or from some

other setting to BALANCE, then the PAN MODE and

PAN parameters will not be recalled. Also, if the recall

causes the PAN MODE to become GANG PAN, the rel-

ative difference of the PAN parameter values following

the recall will be maintained when they are edited.

Support for the Y96K card (from V1.10)

A PLUG-IN screen has been added to the EFFECT func-

tion. Also, PLUGIN parameters have been added to the

RECALL SAFE screen and SELECTIVE RECALL screen of

the SCENE function. These additions are in order to sup-

port the Y96K card that will become available in the near

future from the Waves Corporation. For details on opera-

tion, refer to the owner’s manual for the Y96K.

Please note that the Y96K card will operate as follows.

• Data will be stored/recalled as scene data, but the Undo

function is not supported.

• If you power-off and then power-on the PM5D, con-

ventional scene data will be in the same state as when

you powered-off, but the Y96K will be in the state that

was last stored or recalled.

• If you recall a scene that produces a major change in the

settings of the Y96K, the settings of the Y96K will change

several seconds after recall occurs on the PM5D. If you

want the timing of the change to be synchronized, use

the FADE TIME screen to specify a START OFFSET.

• Do not perform scene store/recall operations in the

Y96K’s update waiting screen. If you do so, the screen

will become inoperable for up to 30 seconds.

• The Scene Store operation saves the Y96K settings in the

PM5D. If you executed Scene Store while the Y96K had

previously been installed, and then once again store the

scene with the Y96K not installed, the previous Y96K

settings will remain. If a scene has never been stored

while the Y96K is installed, recalling that scene with the

Y96K installed will not affect the Y96K in any way.

• In PREVIEW mode, the PLUG-IN screen does not dis-

play the Y96K status.

MIDI EVENT etc. data now maintained

during scene recall (from V1.05)

The MIDI EVENT, GPI OUT CONTROL, and REMOTE

TRANSPORT data included in a scene is now maintained

when a scene recall occurs. This means that if you store a

recalled scene into another scene, this data will be stored as

it was when recalled.

DME series monitor source selection and

EXTERNAL CUE on/off (from V1.05)

A MONITOR button and monitor source select button have

been added to the DME CONTROL screen. When you click

the monitor source select button ( ), the MONITOR

POINT SELECT window will appear, letting you select the

DME series unit monitor source. If the MONITOR button

is on, the EXTERNAL CUE indicator in the upper part of

the display will turn on, and the monitor signal of the DME

series unit will be sent to the PM5D’s CUE bus.

Note

Before turning on the MONITOR button, you must select the

same port as the monitor output on the DME series unit and

as the monitor input for the PM5D. To specify the DME series

unit monitor output, use the “Monitor Out” dialog box of DME

Designer, accessed by [Tools] menu

→

[Monitor]. To specify

the PM5D monitor input, use the MONITOR PORT field on the

SETUP page of the DME CONTROL screen.

DME64N/24N version (from V1.12)

In order to use the DME CONTROL functionality, the

PM5D must be V1.12 or higher, and all connected

DME64N/24N units must be version 1.1 or higher.

PM5DV112E Page 2 Monday, December 27, 2004 11:17 AM

Newly added bulk dump data types

(from V1.05)

The following data types can now be handled by bulk dump.

SETUP data compatibility (from V1.05)

SETUP data created on system software V1.05 or later can-

not be loaded into a system that’s running V1.03 or earlier.

However, SETUP data created on system software V1.03 or

earlier can be loaded by a system that’s running V1.05 or

later.

Scene data compatibility (from V1.10)

In conjunction with Y96K card support, compatibility of

scene data (ALL DATA, SCENE MEMORY, SCENE MEM-

ORY with LINKED LIBRARY) has been changed as follows.

Scene data created with system software V1.10 or later can-

not be loaded into a system running V1.04 or earlier.

However, scene data created on a system running V1.04 or

earlier can be loaded into a system running V1.10 or later.

In this case, the Y96K settings will remain as they were prior

to loading. If you save this data on a system running V1.10

or later, the data size will increase by the amount required

for Y96K support.

A note regarding scenes/libraries imme-

diately after system startup

After the system is started up, the PM5D takes several min-

utes to transfer scene/library data within internal memory.

(The time required depends on the amount of data.) This

means that the following restrictions apply during this time.

• You can’t execute the PASTE button in the GLOBAL

PASTE screen.

• You can’t execute the scene memory UNDO function.

• Scene memory recall will take a bit of time.

Support for Studio Manager (PM5D Edi-

tor) (from V1.10)

Now you can use the included Studio Manager application

software to control the PM5D. For details on Studio Man-

ager, refer to the Studio Manager installation guide.

Data name

(D0)

Data Number

(D1,2)

tx/rx Function

‘K’

512

(Current Data)

tx/rx

Surround Setting

& Request

‘V’

512-

(Current Data)

tx/rx

User Defined Keys

& Request

‘L’

512-

(Current Data)

tx/rx

MIDI Remote &

Request

‘U’

512-

(Current Data)

tx/rx

Fader Mode &

Request

PM5DV112E Page 3 Monday, December 27, 2004 11:17 AM

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

PM5DV112E Page 4 Monday, December 27, 2004 11:17 AM

Yamaha V1 Руководство пользователя

Бренд: Yamaha

Модель: V1

Тип: Руководство пользователя

Это руководство также подходит для

Скачать PDF

сообщить о нарушении

Yamaha V1 Руководство пользователя

Это руководство также подходит для

Yamaha V1 Руководство пользователя

на других языках

Похожие модели бренда