Samsung PS42B430P2W Руководство пользователя

English - 2

User Instructions

Screen Image retention 

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more

than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image

retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

Height 

The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not

install and operate there.

Heat on the top of the PDP TV 

The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper

part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be

prevented from touching the upper part of the product.

The product is making a ‘cracking’ noise. 

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as

temperature or humidity. This is normal and not a defect of the unit.

Cell Defects 

The PDP uses a panel consisting of 2,360,000(HD-level) to 6,221,000(FHD-level) pixels which require sophisticated technology to

produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of

the product.

Avoid operating the TV at temperatures below 5°C(41°F) 

A still image displayed too long may cause permanent damage to the PDP Panel. 

Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left,

right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a

game console may cause similar effect to the screen. Damages caused by the above effect are not covered by

the Warranty.

Afterimage on the Screen. 

Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Warranty 

Warranty does not cover any damage caused by image retention. -

Burn-in is not covered by the warranty. -

Installation 

Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures,

high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may

cause a serious damage to your set.

Digital TV Notice

1. Functionalities related to Digital TV(DVB) are only available in countries/areas where DVB-T (MPEG2 and MPEG4 AVC)

digital terrestrial signals are broadcasted or where you have access to a compatible DVB-C(MPEG2 and MPEG4 AAC)

cable-TV service. Please check with your local dealer the possibility to receive DVB-T or DVB-C signal.

2. DVB-T is the DVB European consortium standard for the broadcast transmission of digital terrestrial television and DVB-C

is that for the broadcast transmission of digital TV over cable.

However, some differentiated features like EPG (Electric Program Guide), VOD (Video on Demand) and so on, are not

included in this specication. So, they cannot be supported at this moment.

3. Although this TV set meets the latest DVB-T and DVB-C standards[August,2008], the compatibility with future DVB-T digital

terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.

4. Some cable-TV providers may charge an additional fee for such a service and you may be required to agree to terms and

conditions of their business.

5. Some Digital TV functions might be unavailable in some countries or regions and DVB-C might not work correctly with all

providers.

6. For more information, please contact your local Samsung customer care centre.

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG

customer care centre. (See back cover for more informations.)

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

N

Product design and specications may be changed without notice in order to enhance product performance.

BN68-02353F-Eng-1.indd 2 2009-06-30 �� 9:30:18

English

N O T

Symbol Press Note One-Touch Button TOOLS

English - 3

Contents

Connecting and Preparing Your TV

Checking Parts ■ ..........................................................................4

Using the Stand-Base ■ ...............................................................4

How to assemble the Stand-Base (depending on the model) ■ ... 4

Viewing the Control Panel ■ ......................................................... 5

Viewing the Connection Panel ■ ................................................... 6

Remote Control ■ ......................................................................... 8

Installing Batteries in the Remote Control ■ ................................. 9

Switching On and Off ■ ................................................................. 9

Placing Your Television in Standby Mode ■ .................................. 9

Viewing the Menus ■ .................................................................. 10

Using the TOOLS Button ■ ......................................................... 10

Viewing the Display ■ ................................................................. 10

Plug & Play Feature ■ ................................................................ 11

Channel Control

Storing Channels ■ ................................................................... 12

Managing Channels ■ ................................................................15

Picture Control

Changing the Picture Settings ■ ................................................. 17

Sound Control

Changing the Sound Setting ■ ...................................................20

Selecting the Sound Mode ■ ...................................................... 21

Function Description

Conguring the Setup Menu ■ ....................................................22

Setting the Time ■ ......................................................................24

Source List / Edit Name ■ ...........................................................25

PC Display ■ ..............................................................................26

Supported Program ■ ................................................................. 27

Recommendations for Use

Teletext Feature ■ .......................................................................28

Wall Mount Kit Specications (VESA) ■ ..................................... 29

Preparing before installing Wall- Mount on the wall ■ ................ 30

Securing the TV to the Wall ■ ..................................................... 30

Troubleshooting ■ ....................................................................... 31

Securing the Installation Space ■ ............................................... 31

Specications ■ .......................................................................... 32

BN68-02353F-Eng-1.indd 3 2009-06-30 �� 9:30:18

English - 4

Using the Stand-Base

Two or more people should carry the PDP. Never lay the PDP on the oor N

because of possible damage to the screen. Always keep the PDP upright.

The PDP can rotate 20 degrees in right and left directions.

N

How to assemble the Stand-Base (depending on the model)

Using the 4 screws for securing the stand base and the monitor, firmly attach the

monitor to the stand base.

(The exterior of the set may be different than the picture.)

In case of installing your TV on the wall, close the

cover (1) on the stand-base connection part using

two screws for hiding.

Warning

Firmly secure the stand to the TV before moving

it, as the stand may fall and could cause serious

injury.

Two or more people should carry the TV.

N

Never lay the TV on the oor because of

possible damage to the screen.

Always store the TV upright.

-20° ~ 20°

Checking Parts

Owner’s Instructions Remote Control/

AAA Batteries (2ea)

Power Cord Cloth-Clean

Warranty Card/

Safety Guide Manual

(Not available in all locations)

Screws (4ea) Cover-Bottom Holder-Ring (4ea)

(Refer to page 30)

Ferrite Core for Power

Cord (1ea)

The ferrite core is used to shield the cable from interference. When connecting a cable, open the ferrite N

core and clip it around the cable near the plug.

Connecting and Preparing Your TV

BN68-02353F-Eng-1.indd 4 2009-06-30 �� 9:30:20

English - 5

Viewing the Control Panel

The product colour and shape may vary depending on the model. N

Front Panel buttons

Touch each button to

operate.

1

SOURCE

Toggles between all the available input sources

(TV, Ext., AV, Component, HDMI1, HDMI2/DVI).

In the on-screen menu, use this button as you would use

N

the ENTER button on the remote control.

2

MENU

Press to see an on-screen menu of your TV’s features.

3

+ –

Press to increase or decrease the volume. In the on-screen

menu, use the + – buttons as you would use the

◄ and ► buttons on the remote control.

4

CH

Press to change channels. In the on-screen menu, use the

CH buttons as you would use the ▲ and ▼ buttons on

the remote control.

5

POWER INDICATOR

Lights up when the power is on.

6

(

POWER)

Press to turn the TV on and off.

7

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

8

SPEAKERS

BN68-02353F-Eng-1.indd 5 2009-06-30 �� 9:30:20

English - 6

Viewing the Connection Panel

Whenever you connect an audio or video system to your set, ensure that all elements are switched off. N

When connecting an external device, match the colour of the connection terminal to the cable. N

The product colour and shape may vary depending on the model. N

1

POWER IN

Connect the supplied power cord.

2

SERVICE 1, 2

Connector for service.

3

COMPONENT IN

Audio (AUDIO L/R) and video (Y/P

B

/P

R

) inputs for

Component.

4

EXT (RGB)

Inputs or outputs for external devices, such as VCR, DVD,

video game device or video disc players.

Input/Output Specification

Connector

Input Output

Video Audio(L/R) RGB Video + Audio(L/R)

EXT

✔ ✔ ✔

Only TV or DTV output

is available.

5

DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio Component.

6

AUDIO OUT(AUDIO R/L)

Connect RCA audio signals from the TV to an external source,

such as Audio equipment.

7 HDMI IN 1, 2 (DVI)

No additional Audio connection is needed for an HDMI to

HDMI connection.

When using an HDMI/DVI cable connection, you must use -

the HDMI IN 2 (DVI) jack.

What is HDMI?

N

High Definition Multimedia interface - allows the

transmission of high denition digital video data and

multiple channels of digital audio.

The HDMI/DVI terminal supports DVI connection to -

an extended device with the appropriate cable (not

supplied). The difference between HDMI and DVI is

that the HDMI device is smaller in size, has the HDCP

(High Bandwidth Digital Copy Protection) coding feature

installed, and supports multi - channel digital audio.

DVI AUDIO IN

DVI audio outputs for external devices.

8

ANT IN

75Ω Coaxial connector for Air/Cable Network.

Input/Output Specification

480i 480p 576i 576p 720p 1080i 1080p

HDMI/DVI 50Hz X X X O O O O

HDMI/DVI 60Hz X O X X O O O

Component O O O O O O O

Cable Television

Network

or

1

43

2

65

or

8

72

TV Rear Panel

BN68-02353F-Eng-1.indd 6 2009-06-30 �� 9:30:21

English - 7

1

COMMON INTERFACE Slot

Insert CI (Common Interface) card into the slot.

(refer to page 23)

When not in - serting CI CARD in some channels,

Scramble Signal is displayed on the screen.

The - pairing information containing a telephone number,

CI CARD ID, Host ID, and other information will be

displayed in about 2~3 minutes. If an error message is

displayed, please contact your service provider.

When the channel - information conguration has nished,

the message Updating Completed is displayed,

indicating that the channel list is now updated.

Insert the CI-Card in the direction marked on it.

N

CAM is not supported in some countries and

N

regions,check with your authorized dealer.

2

AV IN (VIDEO, AUDIO L/R)

Video and audio inputs for external devices, such as a

camcorder or VCR.

The product colour and shape may vary depending on the model. N

TV Side Panel

2

1

BN68-02353F-Eng-1.indd 7 2009-06-30 �� 9:30:21

English - 8

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

The performance of the remote control may be affected by bright light.

N

1

POWER button

(turns the TV on and off)

2

Selects the TV mode directly.

3

Number buttons for direct channel

access

4

Press to switch to your Favourite

channels.

5

Temporary sound switch-off

6

Volume increase

Volume decrease

7

Available source selection

8

Use to see information on the current

broadcast

9

Use to quickly select frequently used

functions.

0

Control the cursor in the menu

!

Used to display Channel Lists on the

screen

@

Use these buttons in the Channel list,

etc.

$

Previous channel

%

Next channel

Previous channel

^

Displays the main on-screen menu

&

Electronic Program Guide (EPG)

display

*

Returns to the previous menu

(

Exit the on-screen menu

)

Turn the audio description function on

or off.

a

Digital subtitle display

Teletext Functions

2

Exit from the teletext display

(depending on the model)

7

Teletext mode selection (LIST/FLOF)

8

Teletext reveal

9

Teletext size

!

Teletext store

@

Fastext topic selection

#

Teletext display/mix both

teletext information and the normal

broadcast

$

Teletext sub page

%

P :Teletext next page

P :Teletext previous page

^

Teletext index

*

Teletext hold

(

Teletext cancel

[ZW

BN68-02353F-Eng-1.indd 8 2009-06-30 �� 9:30:22

English - 9

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the gure.

2. Install two AAA size batteries.

Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside

N

the compartment.

3. Close the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the

N

remote control for a long time.

If the remote control doesn’t work, check the following N

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage or is the power cord unplugged?

5. Is there a special uorescent light or neon sign nearby?

Switching On and Off

The mains lead is attached to the rear of your set.

1. Plug the mains lead into an appropriate socket.

The standby indicator lights up on your set.

N

2. Press the POWER

P

button on your set.

Yo

N

u also can press the POWER

P

button or the TV button on the remote control to turn the TV on.

The programme that you were watching last is reselected automatically.

3. Press the numeric button (0~9) or channel up / down (< / >) button on the remote control or < CH > button on your set.

When

N

you switch the set on for the very rst time, you will be asked to choose language in which the menus are to be displayed.

4. To switch your set off, press the POWER

P

button again.

Placing Your Television in Standby Mode

Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to

interrupt viewing temporarily (during a meal, for example).

1. Press the POWER

P

button on the remote control.

T

N

he screen is turned off and a red standby indicator appears on your set.

2. To switch your set back on, simply press the POWER

P

, numeric buttons (0~9), TV button or channel up / down (< / >) button

again.

Do

N

not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug

the set from the mains and aerial.

BN68-02353F-Eng-1.indd 9 2009-06-30 �� 9:30:22

English - 10

Viewing the Menus

1. With the power on, press the MENU button. The main menu appears on the screen.

The menu’s left side has icons: Picture, Sound, Channel, Setup, Input, Support.

2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTER

E

button

to access the icon’s sub-menu.

3. Press the EXIT button to exit.

The on-screen menus disappear from the screen after about one minute.

N

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and easily. The Tools menu changes depending on

which external input mode you are viewing.

1. Press the TOOLS button. The Tools menu will appear.

2. Press the ▲ or ▼ button to select a menu, then press the ENTER

E

button.

3. Press the ▲ / ▼ / ◄ / ► / ENTER

E

buttons to display, change, or use the selected

items. For a more detailed description of each function, refer to the corresponding page.

Picture Mode, see page 17 •

Sound Mode, see page 20 •

Sleep Timer, see page 24 •

Energy Saving, see page 23 •

Add to Favourite (or Delete from Favourite), see page 15 •

Viewing the Display

The display identifies the current channel and the status of certain audio-video settings.

Press the

O INFO button to viewing the information.

Press the INFO button on the remote control. The TV will display the channel, the type of

sound, and the status of certain picture and sound settings.

▲, ▼: You can view other channel’s information. If you want to move to the currently •

selected channel, press ENTER

E

button.

◄, ►: You can view the desired program’s information at the current channel. •

Press the

N INFO button once more or wait approximately 10 seconds and the display

disappears automatically.

[ZW

DTV Air

15

abc1

18:1 1 Thu 6 Jan

Life On Venus Avenue

Unclassified

No Detaild Information

E Watch

' Information

[ZW

Tools

U

Move

E

Enter

e

Exit

Mode : Standard

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Colour : 50

Tint (G/R) : G50/R50

Picture

Picture Mode ◄ Standard ►

Sound Mode : Custom

Sleep Timer : Off

Energy Saving : Off

Add to Favourite

BN68-02353F-Eng-1.indd 10 2009-06-30 �� 9:30:22

English - 11

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.

The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is running.

N

The Screen Saver is activated if there is no operating signal for longer than 15 minutes. N

1. Press the POWER button on the remote control. You can set the menu language.

menu is automatically displayed. Select the appropriate language by pressing the

▲ or ▼ button.

Press the ENTER

E

button to conrm your choice.

2. Press the ◄ or ► button to select Store Demo or Home Use, then the ENTER

E

button.

We recommend setting the TV to

N Home Use mode for the best picture in your

home environment.

Store Demo

N mode is only intended for use in retail environments.

If the unit is accidentally set to

N Store Demo mode and you want to return to Home Use (Standard): Press the Volume button on

the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.

3. Press the ENTER

E

button. Select the appropriate country by pressing the ▲ or ▼ button. Press the ENTER

E

button to conrm

your choice.

4. Press the ▲ or ▼ button to memorize the channels of the selected connection, then press the ENTER

E

button.

Air: • Air antenna signal.

Cable: • Cable antenna signal.

5. Press the ▲ or ▼ button to select the channel source to memorize. Press the ENTER

E

button to select Start.

Digital & Analogue • : Digital and Analogue channels.

Digital • : Digital channels.

Analogue • : Analogue channels.

For more detailed description of selecting Cable mode,, refer to page 12.

N

The

N

channel search will start and end automatically.

Pr

N

ess the ENTER

E

button at any time to interrupt the memorization process.

A

N

fter all the available channels are stored, the message Set the Clock Mode. is displayed.

6. Press the ENTER

E

button. Press the ▲ or ▼ button to select Auto, then Press the ENTER

E

button.

If

N

you select Manual, Set current date and time is displayed. (refer to page 24)

If

N

you have received a digital signal, the time will be set automatically. If not, see page 24 to set the clock.

7. The brief instruction on How to get the best performance from your new HDTV. is displayed. Press the ENTER

E

button.

Th

N

is menu is available HD Connection Guide in the Support menu.

8. The message Enjoy your TV. is displayed. When you have nished, press the ENTER

E

button.

If you want to reset this feature...

1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup,

then press the ENTER

E

button.

2. Press the ENTER

E

button again to select Plug & Play.

3. Enter your 4 digit PIN number. The default PIN number of a new TV set is

‘0-0-0-0’.

If

N

you want to change PIN number, refer to 22 page.

The

N Plug & Play feature is only available in the TV mode.

Setup

Plug & Play

 ►

Menu Language : English

Time

Broadcast

Security

General

Plug & Play

You can set the menu language.

U

Move

E

Enter

▲

Nederlands

English

Eesti

▼

Menu Language :

BN68-02353F-Eng-1.indd 11 2009-06-30 �� 9:30:22

English - 12

Storing Channels

Country

❑

Digital Channel  : You can change the country for digital channels.

Analogue Channel

 : You can change the country for analogue channels.

The PIN number input screen appears. Enter your 4 digit PIN number. N

Auto Store

❑

Scans for all channels with active broadcast stations (and availability depends on your

country) and stores them in the TV's memory.

You can memorize the channels of the selected connection.

Air • : Air antenna signal.

Cable • : Cable antenna signal.

When selecting Cable,

N

Search Mode • : Displays the search mode. (Quick)

Network ID - : Displays the network identication code.

Frequency - : Displays the frequency for the channel.

Modulation - : Displays available modulation values.

Symbol Rate - : Displays available symbol rates.

Search Mode • : Displays the search mode. (Full, Network)

Frequency - (Start ~ Stop) : Displays the frequency for the channel.

Modulation - : Displays available modulation values.

Symbol Rate - : Displays available symbol rates.

You can memorize the Channel source

Digital & Analogue • : Digital and Analogue channels.

Digital • : Digital channels.

Analogue • : Analogue channels.

If you want to stop

N Auto Store, press the ENTER

E

button.

The

N Stop Auto Store? message will be displayed.

Select

N Yes by pressing the ◄ or ► button, then press the ENTER

E

button.

If a channel is locked using the

N Child Lock function, the PIN input window appears.

Channel Control

Continued...

Channel

Country

 ►

Auto Store

Manual Store

Cable Search Options

Now & Next Guide

Full Guide

Default Guide : Now/Next

BN68-02353F-Eng-1.indd 12 2009-06-30 �� 9:30:22

English - 13

Manual Store

❑

Scans for a channel manually and stores it in the TV’s memory.

Digital Channel 

(DTV)

Manual store for digital channels.

Digital Channel is only available in DTV mode.

N

Channel • : Set the Channel number using the ▲, ▼ or number (0~9) buttons.

Frequency • : Set the frequency using the number buttons.

Bandwidth • : Set the bandwidth using the ▲, ▼ or number (0~9) buttons.

When it has nished, channels are updated in the channel list.

N

Analogue Channel 

Manual store for analogue channel.

Programme • (Programme number to be assigned to a channel): Sets the programme number using the ▲, ▼ or number (0~9)

buttons.

ColourSystem→Auto • / PAL / SECAM / NTSC4.43: Sets the colour system value using the ▲ or ▼ button.

Sound System • → BG / L / I / DK: Sets the sound system value using the ▲ or ▼ button.

Channel • (When you know the number of the channel to be stored): Press the ▲ or ▼ button to select C (Air channel) or

S (Cable channel). Press the ► button, then press the ▲, ▼ or number (0~9) buttons to select the required number.

You can also select the channel number directly by pressing the number (

N

0~9) buttons.

If there is abnormal sound or no sound, reselect the sound standard required.

N

Search • (When you do not know the channel numbers): Press the ▲ or ▼ button to start the search. The tuner scans the

frequency range until the rst channel or the channel that you selected is received on the screen.

Store • (When you store the channel and associated programme number): Set to OK by pressing the ENTER

E

button.

Channel mode

N

C - (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting station in this

mode.

S - (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode.

Cable Search Options (Cable)

❑

You can add directly the channel search range in the network search mode.(Depending

on the each country)

Frequency (Start ~ Stop): • Displays the frequency for the channel.

Modulation • : Displays available modulation values.

Symbol Rate • : Displays available symbol rates.

Set the

N Frequency (Start~Stop) and Symbol Rate using the number (0~9) buttons.

No

❑

w & Next Guide / Full Guide

The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme entries may appear blank or out

of date as a result of the information broadcast on a given channel. The display will dynamically update as soon as new information

becomes available.

Now & Next Guide  : For the six channels indicated in the left-hand column, displays the Current programme and the Next

programme information.

Full Guide: Displays the programme information as time ordered One hour segments. One hours of programme information



is displayed which may be scrolled forwards or backwards in time.

Continued...

BN68-02353F-Eng-1.indd 13 2009-06-30 �� 9:30:22

English - 14

Default Guide

❑

Now/Next  / Full Guide:

You can decide whether to display either the Now/Next or

the Full Guide when the GUIDE button on the remote control is pressed.

You can also display the guide menu simply by pressing the

O GUIDE button.

Using the Now & Next Guide / Full Guide

▲ / ▼ / ◄ / ►

(ENTER)

Select a programme by pressing the ▲/▼/◄/► button.

If the next progrmme is selected, it is scheduled with the clock icon displayed. If the ENTER

E

button is

pressed again, press the ▲/▼/◄/► button to select Cancel Schedules, the scheduling is canceled with the

clock icon gone.

For details about scheduling programmes, refer to the section.

RED Toggle between the Now/Next or Full Guide.

GREEN Full Guide: Scroll backwards quickly (-24 hours).

YELLOW Full Guide: Scroll forwards quickly (+24 hours).

BLUE Exit the guide.

INFO

INFO button for the detailed information. Channel Number, Running Time, Status Bar, Parental Level, Video

Quality Information (HD/SD), Sound Modes, Subtitle or Teletext, languages of Subtitle or Teletext and brief

summary of the highlighted programme are included on the detailed information. “…” will be appeared if the

summary is long.

Channel List

❑

For the detailed procedures on using the Channel List, refer to the descriptions on pages 15~16.

Channel Mode

❑

When the P </> button is pressed, Channels will be switched within the selected channel list.

Added Ch.  : Channels will be switched within the memorized channel list.

Favourite Ch.

 : Channels will be switched within the favourite channel list.

Fine Tune

❑

(only analogue channels)

If the reception is clear, you do not have to ne tune the channel, as this is done automatically during the search and store

operation. If the signal is weak or distorted, you may have to ne tune the channel manually.

Fine tuned channels that have been saved are marked with an asterisk

N * on the right-hand side of the channel number in the

channel banner.

If you do not store the ne-tuned channel in memory, adjustments are not saved.

N

To reset the ne-tuning, select N Reset by pressing the ▼ button and then press the ENTER

E

button.

[ZW

Channel

Now & Next Guide

Full Guide

Default Guide : Now/Next ►

Channel List

Channel Mode : Added Ch.

Fine Tune

Full Guide

DTV Cable 900 f tn 2:10 Tue 1 Jun

Freshmen On Campus

2:00 - 2:30

No Detailed Information

Today 2:00 - 3:00 3:00 - 4:00

Mint Extra

Loaded

Fresh 40 with Dynamite MC

The Distillery

Smash Hits! Sunday

900 f tn

901 ITV Play

902 Kerrang!

903 Kiss

903 oneword

903 Smash Hits!

▼

Street Hypn..

Kisstory

No Information

Freshmen O..

Watch

Information

Page



Now/Next



Exit

Now & Next Guide

DTV Cable 900 f tn 2:10 Tue 1 Jun

Freshmen On Campus

2:00 - 2:30

No Detailed Information

Mint Extra

Loaded

Fresh 40 with Dynamite MC

The Distillery

Smash Hits! Sunday

900 f tn

901 ITV Play

902 Kerrang!

903 Kiss

903 oneword

903 Smash Hits!

▼

Street Hypn..

Kisstory

No Information

Freshmen O..

Watch

Information

Page



Full Guide



Exit

Now Next

BN68-02353F-Eng-1.indd 14 2009-06-30 �� 9:30:23

English - 15

Managing Channels

Using this menu, you can Add / Delete or set Favourite channels and use the programme

guide for digital broadcasts.

Select a channel in the

N All Channels, Added Channels, Favourites, or Programmed

screen by pressing the ▲ or ▼ buttons, and pressing the ENTERE button. Then you

can watch the selected channel.

All Channels • : Shows all currently available channels.

Added Channels • : Shows all added channels.

Favourites • : Shows all favourite channels.

Programmed • : Shows all current reserved programmes.

Using the Colour buttons with the Channel List

N

Red ( - Channel Type): Toggle between your TV, Radio, Data/Other and All.

Green - (Zoom): Enlarges or shrinks a channel number.

Yellow - (Select): Selects multiple channel lists.

T - TOOLS (Tools): Displays the Delete (or Add), Add to Favourite (or Delete from

Favourite), Timer Viewing, Edit Channel Name, Edit Channel Number, Sort,

Lock (or Unlock), Select All (or Deselect All), or Auto Store menu.

(The Options menus may differ depending on the situation.)

Channel Status Display Icons

N

A

An Analogue channel.

c

A channel selected by pressing the yellow button.

♥

A channel set as a Favourite.

(

A programme currently being broadcast.

\

A locked channel.

)

A reserved programme

Press the

O CH LIST button on the remote control to bring up the channel lists.

Channel List Tools Menu

❑

(in All Channels / Added Channels / Favourites)

Press the N TOOLS button to use the tools menu.

Option menu items may differ depending on the channel status.

N

Add  / Delete

You can delete or add a channel to display the channels you want.

All deleted channels will be shown on

N All Channels menu.

A gray-coloured channel indicates the channel has been deleted.

N

The N Add menu only appears for deleted channels.

You can also delete a channel to the

N Added Channels or Favourite menu in the

same manner.

Add to Favourite  / Delete from Favourite

You can set channels you watch frequently as favourites.

Press the T TOOLS button to display Tools menu.

You can also add the favourite channel by selecting Tools → Add to Favourite (or Delete from Favourite).

The “♥” symbol will be displayed and the channel will be set as a favourite.

N

All favourite channels will be shown on N Favourite menu.

To select the Favourite channels you have set up, press the

O FAV.CH button on the

remote control.

[ZW

Continued...

Channel

Full Guide

Default Guide : Now/Next

Channel List

Channel Mode : Added Ch.

Fine Tune

824 UKTV Gold

825 UKTV style

A

1 C --

A

2 C

--

A

3

♥

C

--

A

4 C

--

A

5 C

--

A

6 C

--

A

7 C

--

A

8 C

--

Added Channels

All



Channel Type



Zoom



Select

Tools

824 UKTV Gold

825 UKTV style

A

1 C --

A

2 C

--

A

3

C

--

A

4 C

--

A

5 C

--

A

6 C

--

A

7 C

--

A

8 C

--

All Channels

All



Channel Type



Zoom



Select

Tools

Delete

Add to Favourite

Timer Viewing

Edit Channel Name

Sort

Lock

▼

[ZW

BN68-02353F-Eng-1.indd 15 2009-06-30 �� 9:30:23

English - 16

Timer Viewing 

If you reserve a programme you want to watch, the channel is automatically switched to the reserved channel in the Channel List;

even when you are watching another channel. To reserve a programme set the current time rst. (See page 24)

Only memorized channels can be reserved.

N

You can set the channel, date, or start time directly by pressing the number buttons on the remote control. N

Reserving a programme will be shown on N Programmed menu.

Digital Programme Guide and Viewing Reservation

N

When a digital channel is selected, and you press the ► button, the Programme Guide for the channel appears.

You can reserve a programme according to the procedures described above.

Edit Channel Name  (only analogue channel)

Channels can labeled so that their call letters appear whenever the channel is selected.

The names of digital broadcasting channels are automatically assigned and cannot be labeled. N

Edit Channel Number  (only digital channel)

You can also edit the channel number by pressing the number buttons on the remote control.

Sort  (only analogue channel)

This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using

the auto store.

Lock



/ Unlock

You can lock a channel so that the channel cannot be selected and viewed. This function is available only when the Child Lock is

set to on. (see page 22)

The PIN number input screen appears. Enter your 4 digit PIN number.

N

The default PIN number of a new TV set is ‘0-0-0-0’. You can change the PIN, by selecting

N

Change PIN from the menu.

The “

N \” symbol will be displayed and the channel will be locked.

Select All  / Deselect All

Select All • : You can select all the channels in the channel list.

Deselect Al • l: You can deselect all the selected channels in the channel list.

You can perform the add / delete, add to Favourites / delete from Favourites, or lock / unlock function for multiple channels at

N

the same time. Select the required channels and press the yellow button to set all the selected channels at the same time.

The “

N c” mark appears to the left of the selected channels.

You can only select

N Deselect All when there is a selected channel.

Auto Store 

For further details on setting up options, refer to page 12. N

If a channel is locked using the N Child Lock function, the PIN input window appears.

Channel List Tools Menu

❑

(in Programmed)

You can view, modify or delete a reservation.

Press the

N TOOLS button to use the tools menu.

Change Info • : Select to change a viewing reservation.

Cancel Schedules • : Select to cancel a viewing reservation.

Information • : Select to view a viewing reservation. (You can also change the

reservation information.)

Select All • / Deselect All : You can select (or deselect) all channels in the channel list.

Programmed

1 / 1 / 2009

13:59 5 TV1 Quincy, M.E

18:59 2 TV3 The Equalizer

20:59 2 TV3 McMillan & Wife

21:59 2 TV3 M.Spillane’s mike Hammer

Change Info

Cancel Schedules

Information

Select All

All



Zoom



Select

Tools

Information

BN68-02353F-Eng-1.indd 16 2009-06-30 �� 9:30:24

English - 17

Changing the Picture Settings

Mode

❑

You can select the type of picture which best corresponds to your viewing requirements.

Dynamic • : Selects a high-denition picture for bright environments.

Standard • : Selects the optimal picture display for normal environments.

Movie • : Selects a comfortable picture display for dark environments.

Press the

T

TOOLS button to display Tools menu.

You can also set the picture mode by selecting Tools→PictureMode.

Cell Light

❑

/ Contrast / Brightness / Sharpness / Colour / Tint (G/R)

Your television has several setting options that allow you to control the picture quality.

Cell Light • : Adjusts the pixel brightness.

Contrast • : Adjusts the contrast level.

Brightness • : Adjusts the brightness level.

Sharpness • : Adjusts the sharpness.

Colour • : Adjusts the colour saturation of the picture using the bar on the screen.

Tint (G/R) • : The closer to Red 100, the more saturated the red colour becomes.

Select a picture mode to be adjusted rst. The adjusted values are saved for each picture mode.

N

When you make changes to N Cell Light, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted

accordingly.

In Analogue TV, Ext., AV modes of the PAL system, you cannot use the Tint Function.

N

Settings can be adjusted and stored for each external device you have connected to an input of the TV. N

The energy consumed during use can be signicantly reduced if the level of brightness of the picture is reduced, and then this N

will reduce the overall running cost.

Advanced Settings

❑

Samsung’s new TVs allow you to make even more precise picture settings than

previous models. See below to adjust detailed picture settings.

Advanced Settings

N is available in Standard or Movie mode.

BlackTone→Off  / Dark / Darker / Darkest

You can select the black level on the screen to adjust the screen depth.

DynamicContrast→Off  / Low / Medium / High

You can adjust the screen contrast so that the optimal contrast is provided.

Gamma 

You can adjust the primary colour (Red, Green, Blue) Intensity.

Colour Space 

Colour Space is a colour matrix composed of red, green and blue colours. Select your favourite Colour Space to experience the

most natural colour.

Auto • : Automatically sets the colour range depending on the input video source.

Native • : Sets a colour range wider than that of the input video source.

White Balance 

You can adjust the colour temperature for more natural picture colours.

R-Offset • / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain: Changing the adjustment value will refresh the adjusted screen.

Reset • : Resets the default white balance.

Flesh Tone 

You can emphasize the pink esh tone in the picture.

Changing the adjustment value will refresh the adjusted screen.

N

EdgeEnhancement→Off/On 

You can emphasize object boundaries in the picture.

Picture Control

Continued...

Colour : 50

Tint (G/R) : G50/R50

AdvancedSettings  ►

Picture Options

Picture Reset

Picture

Mode : Standard

►

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Colour : 50

Tint (G/R) : G50/R50

Picture

BN68-02353F-Eng-1.indd 17 2009-06-30 �� 9:30:24

English - 18

Picture Options

❑

Colour Tone  →Cool / Normal / Warm1 / Warm2

You can select the most comfortable colour tone to your eyes.

The adjusted values are stored according to the selected

N Picture mode.

Warm1

N or Warm2 is only activated when the picture mode is Movie.

Size 

You can select the picture size which best corresponds to your viewing requirements.

Auto Wide • : Sets the picture in Auto Wide format.

16:9 • : Sets the picture to the 16:9 aspect ratio.

Wide Zoom • : Select this menu to view 4:3 aspect ratio pictures over a 16:9 aspect ratio TV by stretching the 4:3 picture

vertically.

Zoom • : Stretches the 16:9 aspect ratio picture vertical

4:3 • : Sets the picture to the 4:3 aspect ratio.

Screen Fit • : Displays the full native HD signal that cannot be viewed using a normal TV.

The picture size options may vary depending on the input source.

N

The items available may differ depending on the selected mode. N

Settings can be adjusted and stored for each external device you have connected to an input of the TV. N

Temporary image retention may occur when viewing a static image on the set for more than two hours. N

Wide Zoom N : Press the ► button to select Position, then press the ENTER

E

button.

Press the ▲ or ▼ button to move the screen up / down. Then press the ENTER

E

button.

Zoom

N : Press the ► button to select Position, then press the ENTER

E

button. Press the ▲ or ▼ button to move the picture

up and down. Then press the ENTER

E

button. Press the ► button to select Size, then press the ENTER

E

button.

Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction. Then press the ENTER

E

button.

After selecting

N Screen Fit in HDMI (1080i / 1080p) or Component (1080i / 1080p) mode: Select Position by pressing

the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture.

Reset

N : Press the ◄ or ► button to select Reset, then press the ENTER

E

button. You can initialize the setting.

If you use the

N Screen Fit function with HDMI 720p input, 1 line will be cut at the top, bottom, left and right as in the overscan

function.

Screen Mode 

When setting the picture size to Auto Wide in a 16:9 wide TV, you can determine the picture size you want to see the 4:3 WSS

(Wide Screen Service) image or nothing. Each individual European country requires different picture size so this function is

intended for users to select it.

16:9 • : Sets the picture to the 16:9 aspect ratio.

Wide Zoom • : Select this menu to view 4:3 aspect ratio pictures over a 16:9 aspect ratio TV by stretching the 4:3 picture

vertically.

Zoom • : Stretches the 16:9 aspect ratio picture vertically.

4:3 • : Selects the screen mode as 4:3

This function is available in

N

Auto Wide mode.

This function is not available in,

N

Component or HDMI mode.

Digital NR  →Off / Low / Medium / High / Auto

If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static

and ghosting that may appear on the screen.

When the signal is weak, select one of the other options until the best picture is displayed.

N

HDMI Black Level



→Normal / Low

You can directly select the black level on the screen to adjust the screen depth.

This function is active only when the external input connects to HDMI (RGB signals).

N

Continued...

Tint (G/R) : G50/R50

Advanced Settings

PictureOptions  ►

Picture Reset

Picture

BN68-02353F-Eng-1.indd 18 2009-06-30 �� 9:30:24

English - 19

Film Mode 

You can optimize the picture mode for watching movies.

Off • : Basic video image processing applied and No auto-detection for lm-based programs.

Auto • : Automatically adjusts for the best image quality between lm and video programs.

Screen Burn Protection 

Congures the Screen Burn Protection Options to prevent and reduce pixel burn.

When an image remains in one position too long, it may cause a permanent burn on the screen.

Pixel Shift • : To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This

technology enables you to set picture movement up/down (Vertical) and side to side (Horizontal). The Time setting allows you to

program the time between movement of the picture in minutes.

Set

N

Pixel Shift to On by pressing the ▲ or ▼ button, then press the ENTERE button.

Select the required option by pressing the ▲ or ▼ button, then press the

N

ENTERE button.

Available options:

N

Horizontal, Vertical, Time.

Optimum condition for pixel shift

N

Item TV / Ext / AV/ / Component / HDMI

Horizontal 0~4 2

Vertical 0~4 2

Time (minute) 1~4 min 3 min

The Pixel Shift value may differ depending on the monitor size (inches) and mode.

N

This function is not available in the

N

Screen Fit mode.

Scrolling • : This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern

Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image

on the screen for a long time.

Side Grey • : When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white

balance on both extreme left and right sides.

Dark - : When you set the screen ratio to 4:3, it darkens the left and right sides.

Light - : When you set the screen ratio to 4:3, it brightens the left and right sides.

PictureReset→ResetPictureMode

❑

/ Cancel

Resets all picture settings to the default values.

Select a picture mode to be reset. The reset is performed for each picture mode.

N

Advanced Settings

Picture Options

Picture Reset ►

Picture

BN68-02353F-Eng-1.indd 19 2009-06-30 �� 9:30:24

English - 20

Changing the Sound Setting

Mode→Standard

❑

/ Music / Movie / Clear Voice / Custom

You can select the type of special sound effect to be used when watching a given

broadcast.

Press the T TOOLS button to display Tools menu.

You can also congure the sound mode by selecting Tools → Sound Mode.

Equalizer

❑

The sound settings can be adjusted to suit your personal preferences.

Mode • : You can select a sound mode to suit your personal preferences.

Balance • : Controls the balance between the right and left speakers.

100Hz • / 300Hz / 1KHz / 3KHz / 10KHz (Bandwidth Adjustment): To adjust the level of different bandwidth frequencies

Reset • : Resets the equalizer settings to the default values.

SRSTruSurroundHD→Off

❑

/ On

SRS TruSurround HD is the combined technology of TruSurround and FOCUS, TruBass.

SRS TruSurround HD is down mixing technology that makes the Surround Sound effect of virtual 5.1 channel via two speakers.

This function provide not only rich deep bass at a low-pitched sound but also improve the resolution at a high-pitched sound.

If the sound is abnormal while TV is playing music, please adjust the equalizer and

N SRS TruSurround HD (Off/On).

TruSurround HD, SRS and the symbol are trademarks of SRS Labs, Inc.

TruSurround HD technology is incorporated under license from SRS Labs, Inc.

Audio Language

❑

(only digital channel)

You can change the default value for audio languages. Displays the language information for the incoming stream.

You can only select the language among the actual languages being broadcast.

N

AudioFormat→MPEG

❑

/ Dolby Digital (only digital channel)

When sound is emitted from both the main speaker and the audio receiver, a sound echo may occur due to the decoding speed

difference between the main speaker and the audio receiver. In this case, use the TV Speaker function.

You can only select the language among the actual languages being broadcast.

N

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby Laboratories.

Audio Description

❑

(only digital channel)

This is an auxiliary audio function that provides an additional audio track for visually challenged persons. This function handles the

Audio Stream for the AD (Audio Description), when it is sent along with the Main audio from the broadcaster. Users can turn the

Audio Description On or Off and control the volume.

You can select these options simply by pressing the

O AD button on the remote

control.

AudioDescription→Off  / On

Turn the audio description function on or off.

Volume 

You can adjust the audio description volume.

Volume

N is active when Audio Description is set to On.

Sound Control

Continued...

[ZW

Mode : Custom

►

Equalizer

SRS TruSurround HD : Off

Audio Language : ----

Audio Format : ----

Audio Description

Auto Volume : Off

Sound

BN68-02353F-Eng-1.indd 20 2009-06-30 �� 9:30:24

English - 21

AutoVolume→Off

❑

/ On

Each broadcasting station has its own signal conditions, and so it is not easy to adjust the volume every time the channel is

changed. This feature lets you automatically adjust the volume of the desired channel by lowering the sound output when the

modulation signal is high or by raising the sound output when the modulation signal is low.

SpeakerSelect→ExternalSpeaker

❑

/ TV Speaker

If you want to hear the sound through separate speakers, cancel the internal amplier.

The

N – +, M MUTE buttons do not operate when the Speaker Select is set to External Speaker.

If you select

N External Speaker in the Speaker Select menu, the sound settings will be limited.

TV's Internal Speakers

Audio Out (Optical, L / R Out) to Sound System

TV / Ext. / AV / Component / HDMI

TV / Ext. / AV / Component

/ HDMI

TV Speaker Speaker Output Sound Output

External Speaker Mute Sound Output

Video No Signal Mute Mute

SoundReset→ResetAll/ResetSoundMode/Cancel

❑

You can restore the Sound settings to the factory defaults.

Selecting the Sound Mode

When you set to Dual l ll, the current sound mode is displayed on the screen.

Type of broadcast

On-screen indication

NICAM

Stereo

Regular broadcast

(Standard audio)

Mono (Normal use)

Regular + NICAM Mono

NICAM

Mono

(Normal)

NICAM-Stereo

NICAM

Stereo

Mono

(Normal)

NICAM Dual-I/II

NICAM

Dual-1

NICAM

Dual-2

Mono

(Normal)

A2

Stereo

Regular broadcast

(Standard audio)

Mono (Normal use)

Bilingual or DUAL-I/II

Dual I Dual II

Stereo Stereo

Mono

(Forced mono)

If the stereo signal is weak and an automatic switching occurs, then switch to the mono. N

This function is only activated in stereo sound signal. It is deactivated in mono sound signal. N

This function is only available in N TV mode.

Auto Volume : Off

Speaker Select : TV Speaker

SoundReset  ►

Sound

BN68-02353F-Eng-1.indd 21 2009-06-30 �� 9:30:24

Страница загружается ...

Samsung PS42B430P2W Руководство пользователя

Это руководство также подходит для

Samsung PS42B430P2W Руководство пользователя

на других языках

Похожие модели бренда