RS60
q w
e
r
t y
e
e
w
q
w
t
y
w
w
r
3
4
1
2
YAMAHA
Electronic Drum Rack System
Assembly Instructions
Thank you for purchasing the Yamaha Electronic Drum Rack System RS60.
Before using, thoroughly read this assembly manual, and use this product safely and correctly.
RS60
* Specifications are subject to change without notice.
* Specifications are subject to change without notice.
Before using, please read this “Assembly Instruction” sheet,
and use this product in a safe and proper manner.
The Electronic Drum Rack System will be used in conjunction
with the electronic drum set, pads, stands and foot pedals.
When deciding the area in which you will place the device,
please follow the precautions below.
Especially for small children, parents or an instructor should
teach the children the proper manner in which to use the device.
Always set the instrument on a flat and solid surface.
Placement on a sloping, unstable surface or on steps
may result in the instrument being unstable and over-
turning.
Make sure all bolts are tightened firmly. Loose bolts
may result in the rack overturning or parts dropping
causing injury.
When adjusting the height or angle, do not suddenly
loosen the bolt. The pad may drop or rack pipes may
slip pinching or causing injury to hands or fingers.
Do not sit or step on the rack. The rack may overturn
or be damaged resulting in injury.
The electronic drum set has many pads and stands
so do not play or roughhouse around it. You may hit
your face or head. Many people roughhousing around
the set may result in the set being overturned so chil-
dren should refrain from playing around the set.
Depending upon the strength of the earthquake, strong
shocks may cause the set to overturn or move about.
Stay clear of the set during earthquakes.
If this symbol is ignored and the equipment is
used improperly, fatal injury to persons or se-
rious damage could occur.
Do not put your hands or feet under the foot pedal or
foot switch. They may be pinched resulting in injury.
Watch your fingers when adjusting clamps. They may
become pinched resulting in injury.
Be careful around pipe ends and inside the pipe. Metal
shavings, etc., may injure your fingers. Do not insert
your fingers into the pipe on purpose or for any other
reason.
Only attach pads that have been designed for use on the
rack. Attaching tom toms or other acoustic drums may
damage the clamps; drums may drop, causing injury.
If this symbol is ignored and the equipment is
used improperly, there is a danger of injury to
persons handling the equipment, and material
damage could occur.
• Icons are used to indicate and explain the precau-
tions. To promote the safe and proper use of this prod-
uct, and to protect you and others from injury and
loss of personal property.
• Please read the precautions after you understand
the meaning of the icons.
CAUTION
WARNING
Caution (including danger, or warning). This mark indicates
cautions in which you should pay close attention to.
Acts indicated with this icon are prohibited and should not
be attempted.
This icon indicates acts that you are urged to follow.
● For a move flexible snare/Hi-Hat
setup, set the pads as shown in
the illustration below.
e
e
w
q
w
t
y
w
w
r
Left Side Assembly
(x1)
Right Side Assembly
(x1)
■ RS60 Rack Stand Parts
■ RS60
+
Pad
grouping : Set up example
* Before assembling the rack stand, make sure all of the parts shown below are included.
● Pad and Drum Trigger Grouping (option)
qDTXP
DTXPRESS
Drum Trigger Module
wTP60
Drum Pad
ePCY60
Cymbal Pad
rKP60
Kick Pad
tHH60
Hi-hat Control Pedal
yFoot Pedal
* FP-700 etc.
Center Pipe Assembly (x1)
Module Holder (x1)
(4 screws included)
Module Holder
Clamp (x1)
Hex Rod Cylinder (x6)
Drum Pad Clamp (x3)
Cymbal Holder (x2)
Cable Band (x10)
Tuning Key (x1)
Assembly Instructions
(this sheet)
3
Attach the Drum Pad Clamps
3-1 Insert the Hex Rod Cylinder into the Drum Pad Clamp ,
and tighten the fixing bolt.
3-2 Attach the Drum Pad Clamps
to the tom tom and hi-hat lo-
cations.
3-3 Insert the Hex Rod Cylinder
into the Pads, adjust the angle
and secure.
4
1
Attach the Center Pipe Assembly to the Left Side Assembly
and the Right Side Assembly , and tighten the fixing bolts.
2
Module Holder
DTXP
Hex Rod Cylinder
Attach the Module Holder Clamp
Left Side Assembly
Attach the Center Pipe
Right Side Assembly
Cymbal Holder
Drum Pad Clamp
Hex Rod Cylinder
■ RS60 Assembly
* A screw driver (+ or -) is necessary to complete the assembly.
• Over-tightening of the fixing bolts may result in damage. Take care when tightening fixing bolts and screws.
• When attaching the pads and the DTXPRESS to the rack, make sure their weight is not extremely unbalanced. Also, take into consideration
the forces that are applied while playing the RS60 so that it can be played in a stable condition without excessive deflection.
Step 4-2
Step 3-1
Step 4-1
Step 2-1
Step 2-2
Step 2-3
Step 2-4
Step 3-3
Step 3-2
Cymbal Pad
Tighten
Tighten
Tighten
Tighten
After the above assembly is complete, set the Kick Pad, Hi-Hat Con-
trol Pedal, etc. into position and connect the necessary cables. To
keep cable out of the way while playing, use the supplied Cable Bands
to hold the cables to the rack systems’s pipes.
Drum Pad Clamp
Cymbal Holder
Left Side Assembly
Attach the Module Holder
2-1 Insert the Hex Rod Cylinder into the Module Holder Clamp
, and tighten the fixing bolts.
2-2 Attach the Module Holder Clamp
to the Left Side Assembly
pipe.
2-3 Attach the DTXPRESS to the Module Holder
. With a screw-
driver, use the screws included with the Module Holder to at-
tach the holder to the bottom of the DTXPRESS.
2-4 Attach the Module Holder
(with the DTXPRESS attached)
to the Module Holder Clamp
.
Attach the Cymbal Holders
4-1 Insert the Cymbal Holders into the Cymbal Holder Clamps
that are attach to the left and right sides of the Center Pipe
,
and tighten all fixing bolts.
4-2 Attach the Cymbal Pad to the Cymbal Holders
, adjust the
position and tighten the fixing bolts. (Refer to the Cymbal Pad’s
Owner’s Manual for instructions on attaching the cymbal pad to
the cymbal holder.)
/