Indesit 7OHH 627 IXRU/HA Руководство пользователя

Категория
Кухонные плиты (варочные панели)
Тип
Руководство пользователя
Operating Instructions
OVEN
Contents
Installation, 2-4
Positioning
Electrical connections
Data plate
Assistance
Description of the appliance, 5
Overall view
Control panel
Start-up and use, 6
Starting the oven
Using the cooking timer
Cooking modes, 7-8
Cooking modes
Practical cooking advice
Cooking advice table
Hob, 9
Type of hob
Switching on the glass ceramic hob
Practical advice on using the glass ceramic hob
Precautions and tips, 10
General safety
Disposal
Respecting and conserving the environment
Maintenance and care, 11
Switching the appliance off
Cleaning the appliance
Cleaning the oven door
Replacing the light bulb
Sliding Rack Kit assembly
7OHH 627 RU/HA
7OHH 627 IX RU/HA
GB
Français, 12English,1
RSGB
2
GB
! Before placing your new appliance into operation
please read these operating instructions carefully.
They contain important information for safe use, for
installation and for care of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to possible new owners of
the appliance.
Positioning
! Keep packaging material out of the reach of
children. It can become a choking or suffocation
hazard (
see Precautions and tips
).
! The appliance must be installed by a qualified
person in compliance with the instructions provided.
Incorrect installation may cause harm to persons,
animals or may damage property.
Fitting the appliance
Use the appropriate cabinet to ensure that the
appliance functions properly.
The panels adjacent to the oven must be made of
heat-resistant material.
Cabinets with a veneer exterior must be assembled
with glues which can withstand temperatures of up
to 100°C.
To install the oven under the counter (
see
diagram
) and in a kitchen unit, the cabinet must
have the following dimensions:
! The appliance must not come into contact with
electrical parts once it has been installed.
The consumption indications on the data plate have
been calculated for this type of installation.
Ventilation
To ensure good ventilation, the back panel of the
cabinet must be removed. It is advisable to install the
oven so that it rests on two strips of wood, or on a
completely flat surface with an opening of at least 45 x
560 mm (
see diagrams
).
Centring and fastening
Position the 4 tabs on the side of the oven according
to the 4 holes of the outer frame. Adjust the tabs
according to the thickness of the cabinet side panel,
as shown below:
thickness of 20 mm: take off
the removable part of the tab
(
see diagram
)
thickness of 18 mm: use the
first groove, which has already
been set in the factory (
see
diagram
)
thickness of 16 mm: use the
second groove (
see diagram
)
Secure the appliance to the cabinet by opening the
oven door and putting 4 screws into the 4 holes of the
outer frame.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a
tool.
595
558
min
45
min
575-585
min
560
+4 -0
480
+4 -0
547 min
555
580
500
39
15
595
23
572
543
543
545
560 mm.
45 mm.
Installation
3
GB
Electrical connections
The cooker must be connected to the mains electricity
supply. It is designed to operate with alternating
current at the voltage and frequency indicated on the
data plate (
see the following page
).
The hob is connected to the cooker using a special
connector.
Replace the metal protection after performing all the
necessary hob connections. If the hob is removed
from its position, the red cap which was originally
protecting the red connector must be replaced.
Fitting the power supply cable
1. Open the terminal
board by inserting a
screwdriver into the
side tabs of the cover.
Use the screwdriver as
a lever by pushing it
down to open the cover
(
see diagram
).
2. Loosen the cable
clamp screw and
remove it, using a
screwdriver as a lever
(see figure).
3. Remove the wire
contact screws L-N-
, then fasten the wires
under the screw heads,
respecting the colour
code: Blue (N), Brown
(L) and Yellow-Green
Verde (
).
The terminal board is designed for a 400 V three-
phase connection (
see diagrams below
).
400V 3N~H05RR-F
5x2.5 CEI-UNEL 35363
If the electrical system has other characteristics (
see
diagrams below
), carry out the electrical connection
using the connection supports provided in the box P.
230V ~H05RR-F 3x4
CEI-UNEL 35363
400V 2N~H05RR-F 4x4
CEI-UNEL 35363
3. Secure the power supply cable by fastening the
clamp screw.
4. Close the cover of the terminal board.
BUILT-IN HOB
BUILT-IN COOKER
WHITE RED YELLOWBLUE GREEN
Only on
certain models
NL1L3L2
1
3
2
4
5
N
L2
L1
L3
P
NL
1
3
2
4
5
NL1L2
1
3
2
4
5
4
GB
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load
indicated on the data plate (
see side
).
The appliance must be directly connected to the
mains using an omnipolar circuit-breaker with a
minimum contact opening of 3 mm installed between
the appliance and the mains, suitable for the load
indicated and complying with current electrical
regulations (the earthing wire must not be interrupted
by the circuit-breaker). The supply cable must not
come into contact with surfaces with temperatures
higher than 50°C.
! The installer must ensure that the correct electrical
connection has been made and that it is compliant
with safety regulations.
Before connecting to the power supply, make sure
that:
The appliance is earthed and the plug is compliant
with the law.
The socket can withstand the maximum power of
the appliance, which is indicated on the data plate
(
see below
).
The voltage must be in the range between the
values indicated on the data plate (
see below
).
The socket is compatible with the plug of the
appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced
by authorised technicians only (
see Assistance
).
! The manufacturer declines any liability should
these safety measures not be observed.
DATA PLATE
Dimensions
width 43.5 cm
height 32 cm
depth 41,5 cm
Volume lt. 58
Ele ct ric al
connections
voltage: 230V/400V~ 3N 50/60Hz or
50Hz (see dat a plate)
maximum po wer ab sorbed 10800W
or 10700W
(
see data
p
late
)
ENERGY LABEL
Directive 2002/40/EC on the lab el of
electric ovens.
Standard EN 50304
Energy consumptio n for Natural
co nvection – heati ng mode: /
Convection mode.
Declared energy consumption for
Fo rced convection Class – h eat ing
mode: / Baking.
Th is a pplian ce conforms to the
f ollowing European Economic
Community directives:
2006/95/EEC o f 12/ 12/0 6 (Low
Voltage) and subsequent
amendments;
- 2004/108/EEC of 15/12/04
(Electromagnetic Compatibility) and
su bsequent amendments;
- 93/68/EEC of 22/07/93 and
su bsequent amendments.
- 2002/96/EC and subsequent
amendments.
Assistance
Communicating:
appliance model (Mod.)
serial number (S/N)
This information is found on the data plate located on the appliance and/or on the packaging.
5
GB
Overall view
Description of the
appliance
Control panel
*
Only on certain models
Control panel
GRILL
DRIPPING PAN
GUIDES for the
sliding racks
position 5
position 4
position 3
position 2
position 1
SELECTOR
knob
HOTPLATES
indicator light
EXTENDABLE
HOTPLATES
knob
THERMOSTAT
indicator light
HOTPLATES
knob
HOTPLATES
knob
THERMOSTAT
knob
COOKING
TIMER*
knob
EXTENDABLE
HOTPLATES
knob
6
GB
! The first time you use your appliance, heat the
empty oven with its door closed at its maximum
temperature for at least half an hour. Ensure that the
room is well ventilated before switching the oven off
and opening the oven door. The appliance may
produce a slightly unpleasant odour caused by the
burning away of protective substances used during
the manufacturing process.
Starting the oven
1. Select the desired cooking mode by turning the
SELECTOR knob.
2. Select the desired temperature with the
THERMOSTAT knob See the Cooking advice table for
cooking modes and the suggested cooking
temperatures (
see Cooking Modes
).
3. The THERMOSTAT indicator light indicates that the
oven is heating up to the temperature set.
4. You may do the following during cooking:
- change the cooking mode by turning the SELECTOR
knob
- change the temperature by turning the
THERMOSTAT knob.
- stop cooking by turning the SELECTOR knob to the
“0” position
! Never put objects directly on the oven bottom to
avoid damaging the enamel coating.
! Always place cookware on the rack(s) provided.
Cooling ventilation
In order to cool down the external temperature of the
oven, some models are fitted with a cooling fan that
blows out air between the control panel and the oven
door.
!Once the cooking has been completed, the cooling
fan remains on until the oven has cooled down
sufficiently.
Oven light
When selecting
/ with the SELECTOR knob
the oven light goes on. It remains on when a cooking
mode is selected.
Using the cooking timer*
1. To set the buzzer, turn the COOKING TIMER
knob clockwise almost one complete revolution.
2. Turn the knob anticlockwise to set the desired time:
align the minutes shown on the COOKING TIMER
knob with the indicator on the control panel.
3. When the selected time has elapsed, a buzzer
sounds and the oven turns off.
4. When the oven is off the cooking timer can be used
as a normal timer.
! To use the oven manually, in other words when you
do not wish to use the end of cooking timer, turn the
COOKING TIMER knob until it reaches the 9 symbol.
Start-up and use
*
Only on certain models
7
GB
Cooking modes
! A temperature value can be set for all cooking
modes between 60°C and Max, except for the
following modes:
BARBECUE (recommended: set only to MAX power
level)
GRATIN (recommended: do not exceed 200°C)
/ TRADITIONAL OVEN mode
Both the top and bottom heating elements will come
on. With this traditional cooking mode, it is best to use
one cooking rack only; if more than one rack is used,
the heat will be distributed unevenly.
/ MULTI-COOKING mode
All the heating elements (top, bottom and circular), as
well as the fan, will come on. Since the heat remains
constant throughout the oven, the air cooks and
browns food uniformly. A maximum of two racks may
be used at the same time.
/ BARBECUE mode
The top heating element comes on.
The high and direct temperature of the grill is
recommended for food that requires high surface
temperature. Always cook in this mode with the oven
door closed.
/ GRATIN mode
The top heating element, as well as the fan, will come
on. This combination of features increases the
effectiveness of the unidirectional thermal radiation of
the heating elements through forced circulation of the
air throughout the oven. This helps prevent food from
burning on the surface, allowing the heat to penetrate
right into the food. Always cook in this mode with the
oven door closed.
/ PIZZA mode
The bottom and circular heating elements, as well as
the fan, will come on. This combination heats the oven
rapidly by producing a considerable amount of heat,
particularly from the bottom element. If you use more
than one rack simultaneously, switch the position of
the dishes halfway through the cooking process.
Cooking modes
/ BAKING mode
The rear heating element and the fan come on,
guaranteeing the distribution of heat delicately and
uniformly throughout the oven. This mode is ideal for
baking and cooking temperature sensitive foods
such as cakes that need to rise and to prepare
certain tartlets on 3 shelves simultaneously.
Practical cooking advice
! Do not place racks in position 1 and 5 during fan-
assisted cooking. Excessive direct heat can burn
temperature sensitive foods.
! In the BARBECUE and GRATIN cooking modes,
place the dripping pan in position 1 to collect cooking
residues (fat and/or grease).
MULTI-COOKING
Use position 2 and 4, placing the food that requires
more heat on 2.
Place the dripping pan on the bottom and the rack
on top.
BARBECUE
Insert the rack in position 3 or 4. Place the food in
the centre of the rack.
We recommend that you set the maximum power
level. The top heating element is regulated by a
thermostat and may not always be on.
PIZZA MODE
Use a light aluminium pizza pan. Place it on the
rack provided.
For a crispy crust, do not use the dripping pan
(prevents crust from forming by extending cooking
time).
If the pizza has a lot of toppings, we recommend
adding the mozzarella cheese on top of the pizza
halfway through the cooking process.
8
GB
Cooking advice table
Cooking
modes
Foods Weight
(in kg)
Rack position Pre-heating
time (min)
Recommended
temperature
Cooking
time
(minutes)
Convection
Oven
Duck
Roast veal or beef
Pork roast
Biscuits (short pastry)
Tarts
1
1
1
-
1
3
3
3
3
3
15
15
15
15
15
200
200
200
180
180
65-75
70-75
70-80
15-20
30-35
Multi-cooking
Pizza (on 2 racks)
Lasagne
Lamb
Roast chicken + potatoes
Mackerel
Plum cake
Cream puffs (on 2 racks)
Biscuits (on 2 racks)
Sponge cake (on 1 rack)
Sponge cake (on 2 racks)
Savoury pies
1
1
1
1+1
1
1
0.5
0.5
0.5
1
1.5
2 and 4
3
2
2 and 4
2
2
2 and 4
2 and 4
2
2 and 4
3
15
10
10
15
10
10
10
10
10
10
15
230
180
180
200
180
170
190
180
170
170
200
15-20
30-35
40-45
60-70
30-35
40-50
20-25
10-15
15-20
20-25
25-30
Barbecue
Soles and cuttlefish
Squid and prawn kebabs
Cod filet
Grilled vegetables
Veal steak
Cutlets
Hamburgers
Mackerels
Toasted sandwiches
1
1
1
1
1
1
1
1
n.° 4
4
4
4
3 or 4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
MAX
MAX
MAX
MAX
MAX
MAX
MAX
MAX
MAX
8-10
6-8
10
10-15
15-20
15-20
7-10
15-20
2-3
Gratin
Grilled chicken
Cuttlefish
1.5
1.5
2
2
10
10
200
200
55-60
30-35
Pizza Mode
Pizza
Roast veal or beef
Chicken
0.5
1
1
3
2
2 or 3
15
10
10
220
220
180
15-20
25-30
60-70
Baking Mode
Tarts
Fruit cakes
Plum cake
Sponge cake
Stuffed pancakes (on 2 racks)
Small cakes (on 2 racks)
Cheese puffs (on 2 racks)
Cream puffs (on 3 racks)
Biscuits (on 3 racks)
Meringues (on 3 racks)
0.5
1
0.7
0.5
1.2
0.6
0.4
0.7
0.7
0.5
3
2 or 3
3
3
2 and 4
2 and 4
2 and 4
1 and 3 and 5
1 and 3 and 5
1 and 3 and 5
15
15
15
15
15
15
15
15
15
15
180
180
180
160
200
190
210
180
180
90
20-30
40-45
40-50
25-30
30-35
20-25
15-20
20-25
20-25
180
9
GB
Hob
Type of hob
The oven is combined with a hob
that can be made up of two types of
heating elements: cast-iron electric
plates (
see diagram 1
) or glass
ceramic hobs, which may be
traditional (
see diagram 2
) or with
extendable cooking zones (
see
diagram 3
).
Switching on the glass ceramic hob
Traditional cooking zones
Traditional cooking zones are made up of circular
heating elements. They turn red approximately ten
seconds after they have been turned on.
Each cooking zone is fitted with a control knob allowing
you to select from 9 different temperature settings from a
minimum of 1 to a maximum of 9.
Extendable cooking zones
The extendable radiant elements (B) are recognisable by
the fact that they have a double heating zone. You can
turn on only the smaller internal cooking zone or both the
external and internal zones.
The control knob allows you to choose between two
power levels, which are both adjustable between a
minimum value of 1 to a maximum of 9:
The lowest power level can be set by turning the
knob clockwise from 1 to 9.
Turn the knob to completely
(
AA
AA
A) until you hear a
slight click, to enable the maximum power level,
which in turn can be adjusted between 9 and 1 by
turning the knob anticlockwise. To restore the
minimum power level, turn the knob and set it back
to position 0.
For double cooking zones, the first part of the knob
movement activates the smaller cooking zone
(internal). To activate both (internal and external), it is
necessary to turn the knob completely (
AA
AA
A) and then
select the desired power level between 9 and 1.
Residual heat indicator lights (only available on
certain models)
The indicator lights (C) indicate that the temperature of
the corresponding cooking zones have exceeded 60°C,
even after the heating element has been switched off.
Recommended power levels for varus types of cooking:
Power Radiant plate
0OFF
1 To melt butter or chocolate
2 and 3 To heat liquids
4 To prepare creams or sauces
5 To boil meat
6 To cook pasta or rice
7 and 8 To cook meats, fish, omelettes
9 To fry
A
Activation of both cooking zones
Practical advice on using the glass
ceramic hob
!The glue that is applied on the gaskets leaves some
traces of grease on the glass. Before using the
appliance, we recommend you eliminate these with a
special non-abrasive cleaning product. During the first
few hours of use there may be a smell of rubber which
will disappear very quickly.
To obtain the best results with your hob:
Use flat-bottomed pans to ensure that they adhere
to the cooking zone perfectly.
Always use pans with a diameter that is large enough
to cover the hotplate fully, in order to use all the
available heat.
Make sure that the bottom of the cookware is always
dry and clean to guarantee correct adherence and
long life, not only for the cooking zones but also for
the cookware itself.
Avoid using the same cookware that is used on gas
burners: the heat concentration on gas burners may
deform the base of the pan, causing it not to adhere
correctly.
Never leave a cooking zone on without cookware on it
because as it heats up and rapidly reaches the
maximum level, it could damage the heating
elements.
C
A
A
A
A
C
A
A
B
B
diagram 2
diagram 3
diagram 1
10
GB
Precautions and tips
! The appliance was designed and manufactured in
compliance with international safety standards. The
following warnings are provided for safety reasons and must
be read carefully.
General safety
The appliance was designed for domestic use inside
the home and is not intended for commercial or
industrial use.
The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
When handling the appliance, always use the handles
provided on the sides of the oven.
Do not touch the appliance with bare feet or with wet or
moist hands and feet.
The appliance must be used by adults only for
the preparation of food, in accordance with the
instructions outlined in this booklet. Any other
use of the appliance (e.g. for heating the room)
constitutes improper use and is dangerous.
The manufacturer may not be held liable for
any damage resulting from improper, incorrect
and unreasonable use of the appliance.
Do not touch the heating elements and parts of the
oven door when the appliance is in use; these parts
become extremely hot. Keep children well away from
the appliance.
Ensure that the power supply cable of other electrical
appliances does not come into contact with the hot parts
of the oven.
The openings used for ventilation and dispersion of
heat must never be covered.
Always grip the oven door handle in the centre: the
ends may be hot.
Always use oven gloves to place cookware in the oven
or when removing it.
Do not use aluminium foil to line the bottom of the oven.
Do not place flammable materials in the oven: if the
appliance is switched on by mistake, it could catch
fire.
Always make sure the knobs are in the “z”/“
{” position
when the appliance is not in use.
When unplugging the appliance always pull the plug
from the mains socket, do not pull on the cable.
Never carry out any cleaning or maintenance work
without having unplugged the plug from the mains.
In the case of a malfunction, under no circumstances
should you attempt to repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or further malfunctioning of the appliance.
Contact a Service Centre (
see Assistance
).
Do not rest heavy objects on the open oven door.
The glass ceramic hob is resistant to mechanical
shocks, but it may crack (or even break) if hit with a
sharp object such as a tool. If this happens,
disconnect the appliance from the electricity mains
immediately and contact a Service Centre.
Remember that the temperature of the cooking zones
remains relatively high for at least thirty minutes after
they have been switched off.
Keep any object that could melt away from the hob, for
example plastic and aluminium objects, or products with
a high sugar content. Keep plastic or aluminium objects
away from the hob: if you forget them on surfaces that
are still hot, they may cause serious damage to the
hob.
The appliance should not be operated by people
(including children) with reduced physical,
sensory or mental capacities, by inexperienced
individuals or by anyone who is not familiar with
the product. These individuals should, at the very
least, be supervised by someone who assumes
responsibility for their safety or receive
preliminary instructions relating to the operation of
the appliance.
Do not let children play with the appliance.
Disposal
Observe local environmental standards when disposing
packaging material for recycling purposes. Observe
existing legislation when disposing of the old appliance.
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed of
in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimise the recovery and recycling of the materials they
contain and reduce the impact on human health and the
environment. The crossed out “wheeled bin” symbol on
the product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or retailer
for information concerning the correct disposal of their
old appliance.
Respecting and conserving the environment
By using the appliance in the hours between late
afternoon and early morning, you can help reduce the
work load placed on electrical companies.
Always keep the oven door closed when using the GRILL
mode to obtain best results and to save energy
(approximately 10%).
Regularly check the door seals and wipe clean to ensure
they are free of debris so that they adhere properly to the
door and do not allow heat to escape.
11
GB
Maintenance and care
Switching the appliance off
Disconnect your appliance from the electricity supply
before carrying out any work on it.
Cleaning the appliance
The stainless-steel or enamel-coated external parts as
well as the rubber seals may be cleaned using a
sponge that has been soaked in lukewarm water and
neutral soap. If these stains are difficult to remove,
use only specialised products. After cleaning, rinse
and dry thoroughly. Do not use abrasive powders or
corrosive substances.
Ideally, the inside of the oven should be cleaned after
each use, when it is still lukewarm. Use hot water and
detergent, rinse and dry with a soft cloth. Do not use
abrasive products.
All accessories - with the exception of the sliding
racks - can be washed like everyday crockery, and
are even dishwasher safe.
! Never use steam cleaners or pressure cleaners on
the appliance.
Cleaning the oven door
Clean the glass part of the oven door using a sponge
and a non-abrasive cleaning product, then dry
thoroughly with a soft cloth. Do not use rough abrasive
material or sharp metal scrapers as these could scratch
the surface and cause the glass to crack.
To clean more thoroughly, you
can remove the oven door.
1. Open the oven door fully
(
see diagram
).
2. Use a screwdriver to lift up
and turn the small levers
FF
FF
F
located on the two hinges (
see
diagram
).
3. Grip the door on the two
external sides and close it
approximately half way. Unlock
the door by pressing on the
clamps
FF
FF
F, then pull the door
towards you lifting it out of its
seat (
see diagram
).*
3. Grip the door on the two
outer sides and close it
approximately half way. Pull
the door towards you lifting it
out of its seat (
see diagram
).*
To replace the door, reverse
this sequence.
Inspecting the seals
Check the door seals around the oven periodically. If
the seals are damaged, please contact your nearest
After-sales Service Centre (
see Assistance
). We
recommend not using the oven until the seals have
been replaced.
Replacing the light bulb
To replace the oven light bulb:
1. Remove the glass cover of
the lamp-holder.
2. Remove the light bulb and
replace it with a similar one:
Wattage 25 W, cap E 14.
3. Replace the glass cover (
see
diagram
).
Sliding Rack Kit assembly
To assemble the sliding racks:
1. Loosen the two screws A
(
see diagram
). If the oven is
fitted with self-cleaning panels,
these will have to be temporarily
disassembled.
2. Replace the screws A with the
screws and spacers (B + C) supplied
with the kit.
3. Tighten the new screws B and the
corresponding spacers C, fitting the
self-cleaning panels on again.
4. Secure the two joints D of the
guide rail in the holes provided
on the oven walls (
see diagram
).
The holes for the left guide rail
are situated at the top, while the
holes for the right one are at the
bottom.
5. Finally, fit the guide rail on the spacer C.
! Do not place the sliding racks in position 5.
F
F
F
B
C
D
A
A
*
Only on certain models
Содержание
Монтаж, 13-14
Расположение
Электрическое подсоединение
Паспортная табличка
Техническое обслуживание
Описание изделия, 16
Общий вид
Панель управления
Включение и эксплуатация, 17
Включение духового шкафа
Программирование окончания приготовления при
помощи таймера
Программы, 18- 19
Программы приготовления
Практические советы по приготовлению
Таблица приготовления
Варочная панель, 20
Модели варочной панели
Включение стеклокерамической варочной панели
Практические рекомендации по использованию
стеклокерамической варочной панели
Предосторожности и рекомендации, 21
Общие требования к безопасности
Утилизация
Экономия электроэнергии и охрана окружающей
среды
Техническое обслуживание и уход, 22-
23
Отключение электропитания
Чистка изделия
Чистка дверцы
Замена лампочки
Крепление комплекта выдвижных направляющих
Руководство по
эксплуатации
ДУХОВОЙ ШКАФ
7OHH 627 RU/HA
7OHH 627 IX RU/HA
English, 1
RS
GB
Русский,
1212
1212
12
RS
RS
! Важно сохранить данное руководство для его
последующих консультаций. В случае продажи,
передачи изделия или при переезде на новое место
жительства необходимо проверить, чтобы
руководство оставалось вместе с изделием, для
того чтобы его новый владелец мог ознакомиться с
правилами эксплуатации и с соответствующими
предупреждениями.
! Внимательно прочитайте инструкции: в них
содержатся важные сведения об установке,
эксплуатации и безопасности изделия.
Расположение
! Не разрешайте детям играть с упаковочными
материалами. Упаковочные материалы должны
быть уничтожены в соответствии с правилами
раздельного сбора мусора (см. Предосторожности
и рекомендации).
! Установка изделия производится в соответствии с
данными инструкциями квалифицированными
специалистами. Неправильная установка изделия
может стать причиной повреждения имущества и
причинить ущерб людям и домашним животным.
Встроенный монтаж
Для обеспечения исправного функционирования
изделиякухонный элемент должен иметь
соответствующие характеристики:
панели кухонных элементов, прилегающих к
духовому шкафу, должны быть выполнены из
термостойкого материала.
клей кухонных элементов элементов из
фанерованного дерева должен быть устойчивым
к температуре 100°C.
для встраивания духового шкафапод кухонным
топом (см. рисунок) или в колонну ниша кухонного
элемента должна иметь следующие размеры:
! После встраивания изделия в кухонный элемент
должна быть исключена возможность касания к
электрическими частями.
Расход электроэнергии, указанный на паспортной
табличке изделия, был замерен для данного типа
монтажа.
Вентиляция
Для обеспечения надлежащей вентиляции
необходимо снять заднюю панель ниши кухонного
элемента. Рекомендуется установить духовой шкаф
на два деревянных бруска или на сплошное
основание с отверстием диаметром не менее 45 х
560 мм (см чертежи).
Центровка и крепление
4 крепежных элемента с боков духового шкафа
должны быть отрегулированы в соответствии с 4
отверстиями в раме в зависимости от толщины
боковой панели кухонного элемента:
толщина 20 мм: полностью
удалите съемную часть
крепежного элемента (см.
рисунок);
толщина 18 мм: использовать
первый паз, согласно уже
готовой конфигурации
производителя (см. рисунок);
толщина 16 мм: использовать
второй паз (см. рисунок).
Для крепления изделия к кухонному элементу: откройте
двурцу духового шкафа и завинтите 4 шурупа для
деревянных панелей в 4 отверстия в раме.
! Все защитные элементы должны быть закреплены
таким образом, чтобы их можно было снять только
при помощи специального инструмента.
595
558
min
45
min
575-585
min
560
+4 -0
480
+4 -0
547 min
555
580
500
39
15
595
23
572
543
543
545
560 mm.
45 mm.
Монтаж
14
RS
Электрическое подсоединение
Электрическое подсоединение изделия
выполняеться с кухонной плитой, расчитанной на
переменный ток, с напряжением и частотой,
указанными на паспортной табличке (см. следующую
страницу).
Варочная панель соединяется с кухонной плитой
при помощи специального разъема.
bqŠpnemm`“
b`pn)m`“ o`mek|
bqŠpnemm{i drunbni xj`t
aek{i jp`qm{i fekŠ{iqhmhi gekem{i
h2“ 2%*% "
…*%2%!/. % .
Установите на место защитную металлическую
заглушку после электрического подключения
варочной панели. В случае демонтажа варочной
панели необходимо установить на свое место
красную заглушку на красный разъем.
Подсоединение сетевого шнура
1. Откройте зажимную
коробку, нажав при
помощи отвертки на
выступы с боков
крышки: потяните и
откройте крышку (см.
рисунок).
2. Отвинтите винт
кабельного сальника и
выньте его, поддев
отверткой (см. схему).
3. Отвинтите винты
контактов L-N-
и
затем прикрепите
провода под
головками винтов,
соблюдая цветовую
маркировку Синий (N)
Коричневый (L) Желто-
зеленый (
).
Зажимная коробка расчитана на трехфазное
электропитание 400 В (см. рисунки ниже).
400В 3N~H05RR-F
5x2.5 CEI-UNEL 35363
Если электропроводка имеет другие
характеристики (см. рисунки ниже), для
электрического подсоединения используйте
соединительные перемычки, расположенные
внутри коробки Р.
230В ~H05RR-F 3x4
CEI-UNEL 35363
400В 2N~H05RR-F 4x4
CEI-UNEL 35363
3. Закрепите сетевой шнур в специальном
кабельном сальнике.
4. Закройте крышку зажимной коробки.
N
L2
L1
L3
P
NL
1
3
2
4
5
NL1L2
1
3
2
4
5
NL1L3L2
1
3
2
4
5
RS
Техническое обслуживание
! Никогда не обращайтесь к неуполномоченным техникам.
При обращении в Центр Технического обслуживания сообщите:
Тип неисправности;
Модель изделия (Мод.)
Номер тех. паспорта (серийный №)
Эти данные вы найдете на паспортной табличке, расположенной на изделии.
Подсоединение сетевого шнура к сети
электропитания
Установите на сетевой шнур нормализованную
штепсельную вилку, расчитанную на нагрузку,
указанную на паспортной табличке (см. сбоку).
В случае прямого подключения к сети электропитания
между кухонной плитой и сетью необходимо установить
мультиполярный выключатель с минимальным
расстоянием между контактами 3 мм, расчитанный на
данную нагрузку и соответствующий действующим
нормативам (выключатель не должен размыкать провод
заземления). Сетевой шнур должен быть расположен таким
образом, чтобы ни в одной точке его температура не
превышала температуру помещения более чем на 50°C.
! Электромонтер несет ответственность за
правильное подключение изделия к электрической
сети и за соблюдение правил безопасности.
Перед подсоединением сетевого шнура проверьте
следующее:
розетка должна быть соединена с заземлением и
соответствовать нормативам;
сетевая розетка должна быть рассчитана на
максимальную потребляемую мощность изделия,
указанную на паспортной табличке (см. ниже);
напряжение сети электропитания должно
находиться в пределах значений, указанных на
паспортной табличке (см. ниже);
сетевая розетка должна быть совместима со
штепсельной вилкой изделия. В противном
случае замените розетку или вилку; не
используйте удлинители или тройники.
! Изделие должно быть установлено таким образом,
чтобы электрический провод и сетевая розетка
были легко доступны.
! Электрический провод изделия не должен быть
согнут или сжат.
! Регулярно проверяйте состояние сетевого шнура
и в случае необходимости поручите его замену
только уполномоченным техникам (см. Техническое
обслуживание).
! Производитель не несет ответственности за
последствия несоблюдения перечисленных
требований.
ПАСПОРТНАЯ ТАБЛИЧК
А
Габаритные
размеры
шир ина 43, 5 см.
высота 32 см.
глубина 41,5 см.
Объем л 5
8
Эл ектропитание
напряжение 230
400 В ~ 3N
50/60 Гц или 50 Гц (см.
паспортную табличк у)
макс. поглощаемая мощность
10800 Вт или 10700 Вт (см.
паспо
р
тн
у
ю табличк
у)
МАРКИРОВКА
ПОТРЕБЛЕНИЯ
ЭЛЕКТРОЭНЕРГИИ
Директива 2002/40/СЕ об
этикетках электрических духовых
шкафов. Норматив EN 50304 -
Пот ребление электроэнергии -
Нат ураль ная конвекция
режим нагрева: /
Стандартная;
Заявление о расходе
элект роэнергии класса
принудительной конвекции -
функция нагревания: /
Кондитерская
выпечка.
Данное изделие соответствует
следующим Директивам
Евр опейского Сообщества:
2006/ 95/CEE от 12/12/06 (Низкое
напряжение) с последующими
изменениями 2004/108/СЕЕ от
15/12/04 (Электромагнитная
совместимость) с последующими
изменениями 93/68/СЕЕ от
22/07/93 с по следующими
изменениями. - 2002/96/СЕ с
послед
ющими изменениями.
16
RS
Панель управления
РЕШЕТКА
ПРОТИВЕНЬ
ВЫДВИЖНЫЕ
НАПРАВЛЯЮЩИЕ
для противеней и решеток
положение 5
положение 4
положение 3
положение 2
положение 1
*
Имеется только в некоторых моделях
Описание изделия
Общий вид
Панель управления
RS
! При первом включении духового шкафа
рекомендуем прокалить его примерно в течение 30
минут при максимальной температуре с закрытой
дверцей. Затем выключите духовой шкаф, откройте
дверцу и проветрите помещение. Запах, который
вы можете почувствовать, вызван испарением
веществ, использованных для предохранения
духового шкафа.
Включение духового шкафа
1. Выберите нужную программу приготовления при
помощи рукоятки ПРОГРАММЫ.
2. Выберите температуру при помощи регулятора
ТЕРМОСТАТ. В специальной таблице приводится
перечень типов приготовления с соответствующими
рекомендуемыми температурами (см. Программы).
Включенный индикатор ТЕРМОСТАТА означает
текущую фазу нагрева духовки до заданной
температуры.
В процессе приготовления в любой момент можно:
- изменить программу приготовления при помощи
рукоятки ПРОГРАММЫ;
- изменить температуру при помощи регулятора
ТЕРМОСТАТ;
- прервать приготовление, повернув рукоятку
ПРОГРАММЫ в положение «0».
! Никогда не ставьте никаких предметов на дно
духового шкафа, так как они могут повредить
эмалированное покрытие.
! Всегда ставьте посуду на прилагающуюся
решетку.
Охладительная вентиляция
Для понижения температуры вокруг работающего
духового шкафа некоторые модели оснащаются
охладительным вентилятором. Этот вентилятор
направляет струю воздуха между панелью
управления и дверцей духового шкафа.
По завершении приготовления вентилятор
продолжает работать вплоть до надлежащего
охлаждения духовки.
! По завершении приготовления вентилятор
продолжает работать вплоть до надлежащего
охлаждения духовки.
Освещение духового шкафа
Загорается при выборе
/ при помощи
рукоятки ПРОГРАММЫ. Остается включенной при
выборе программы приготовления.
Программирование окончания
приготовления при помощи таймера*
1. Прежде всго необходимо завести таймер,
повернув рукоятку ТАЙМЕР ОКОНЧАНИЯ
ПРИГОТОВЛЕНИЯ по часовой стрелке почти на
один полный оборот.
2. Поворачивая рукоятку обратно, против часовой
стрелки, задается нужное время – минуты на
рукоятке ТАЙМЕРА ОКОНЧАНИЯ
ПРИГОТОВЛЕНИЯ должны совпасть с отметками
на панели управления.
3. По истечении заданного времени раздается
звуковой сигнал и духовой шкаф выключается.
4. Когда духовой шкаф выключен, таймер
программирования окончания приготовления может
быть использован в качестве обычного таймера.
! для использования духового шкафа в ручном
режиме, т.е. исключив устройство
программирования окончания приготовления,
необходимо, чтобы фиксированная отметка на
передней панели духовки совпала с символом 9.
Включение и эксплуатация
*
Имеется только в некоторых моделях
18
RS
Программы приготовления
! Для всех программ можно задать температуру от
60°C до МАКС кроме:
ГРИЛЬ (рекомендуется устанавливать только
МАКС. температуру);
ПОДРУМЯНИВАНИЕ (рекомендуется не
превышать температуру 200°C).
/ Programma ТРАДИЦИОНАЛЬНАЯ
ДУХОВКА
Включаются два нагревательных элемента:
нижний и верхний. В режиме традиционального
приготовления рекомендуется использовать
только один уровень: при использовании
нескольких уровней распределение температуры
будет неоптимальным.
/ Программа ОДНОВРЕМЕННОЕ
ПРИГОТОВЛЕНИЕ
Включаются все нагревательные элементы
(верхний, нижний и круглый) и вентилятор. Так как
жар является постоянным во всем духовом
шкафу, воздух обеспечивает однородное
приготовление и подрумянивание продукта.
Одновременно можно использовать не более двух
уровней духового шкафа.
/ Программа ГРИЛЬ
Включается верхний нагревательный элемент.
Высокая температура и жар прямого действия
гриля рекомендуется для приготовления
продуктов, нуждающихся в высокой
поверхностной температуре. Готовьте блюда с
закрытой дверцей духового шкафа.
/ Программа GRATIN (Подрумянивание)
Включается верхний нагревательный элемент и
вертел. Сочетает однонаправленное выделение
жара с принудительной циркуляцией воздуха
внутри духового шкафа. Это препятствует
обгоранию поверхности продуктов, повышая
проникающую способность жара. Готовьте блюда
с закрытой дверцей духового шкафа.
/ Программа ПИЦЦА
Включаются нижний и круглый нагревательные
элементы и вентилятор. Такое сочетание позволяет
быстро разогреть духовку с более сильным
выделением жара снизу. Если используются
несколько уровней одновременно, необходимо
менять местами блюда в середине их приготовления.
/ Программа КОНДИТЕРСКАЯ
ВЫПЕЧКА
Включается задний нагревательный элемент и
вентилятор, обеспечивая умеренный и
однородный жар внутри духовки. Данная функция
рекомендуется для приготовления деликатных
блюд (например, кондитерских изделий,
требующих подъема теста) и мелкой выпечки
одновременно на трех уровнях.
Практические советы по
приготовлению
! В режиме вентилируемого приготовления не
используйте 1-ый и 5-ый уровни: они
подвергаются прямому воздействию горячего
воздуха, который может сжечь деликатные
продукты.
! При использовании функций ГРИЛЬ и
ПОДРУМЯНИВАНИЕ поместите противень на
уровень 1 для сбора жидкостей, выделяемого при
жарке (сок и/или жир).
ОДНОВРЕМЕННОЕ ПРИГОТОВЛЕНИЕ
Используются 2-ой и 4-ый уровни, на 2-ой
помещаются продукты, требующие более
интенсивного жара.
Установите проитвень снизу, а решетку сверху.
ГРИЛЬ
Установите решетку на уровень 3 или 4,
поместите продукты в центр решетки.
Рекомендуется выбрать максимальную
мощность духовки. Не беспокойтесь, если
верхний элемент не остается постоянно
включенным: его работа управляется
термостатом.
ПИЦЦА
Используйте противень из легкого алюминия,
устанавливая его на прилагающуюся решетку.
При использовании противеня время выпечки
удлиняется, что затрудняет получение
хрустящей пиццы.
В случае выпечки пиццы с обильной начинкой
рекомендуется положить на пиццу сыр
моццарелла в середине выпечки.
Программы
RS
Таблица приготовления
Программы
Продукты
Вес
(кг)
Уровень
Время
нагревания
(мин.)
Рекомендуемая
температура
Продолжит-ть
приготовления
(минуты)
Традициональная
духовка
Утка
Жаркое из телятины или
говядины
Жаркое из свинины
Печенье (песочное)
Песочный торт с начинкой
1
1
1
-
1
3
3
3
3
3
15
15
15
15
15
200
200
200
180
180
65-75
70-75
70-80
15-20
30-35
Одновременное
приготовление
Пицца (на 2-х уровнях)
Лазанья
Баранина
Жареная курица с картошкой
Скумбрия
Кекс
Эклеры (на 2-х уровнях)
Печенье (на 2-х уровнях)
Бисквит (на 1-ом уровне)
Бисквит (на 2-ух уровнях)
Несладкие торты
1
1
1
1+1
1
1
0.5
0.5
0.5
1
1.5
2 и 4
3
2
2 и 4
2
2
2 и 4
2 и 4
2
2 и 4
3
15
10
10
15
10
10
10
10
10
10
15
230
180
180
200
180
170
190
180
170
170
200
15-20
30-35
40-45
60-70
30-35
40-50
20-25
10-15
15-20
20-25
25-30
ГРИЛЬ
Камбала и каракатицы
Кальмары и креветки на
шампурах
Филе трески
Овощи-гриль
Телячий бифштекс
Отбивные
Гамбургер
Скумбрия
Горячие бутерброды
1
1
1
1
1
1
1
1
4 шт.
4
4
4
3 или 4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
MAКС.
MAКС.
MAКС.
MAКС.
MAКС.
MAКС.
MAКС.
MAКС.
MAКС.
8-10
6-8
10
10-15
15-20
15-20
7-10
15-20
2-3
Gratin
(Подрумянивание)
Курица-гриль
Морские каракатицы
1.5
1.5
2
2
5
5
200
200
55-60
30-35
Пицца
Пицца
Жаркое из телятины или
говядины
Курица
0.5
1
1
3
2
2 или 3
15
10
10
220
220
180
15-20
25-30
60-70
Кондитерская
выпечка
Песочный торт с начинкой
Фруктовый торт
Кекс
Бисквит
Блины с начинкой (на 2-х
уровнях)
Мелкие кексы (на 2-х уровнях)
Печенья из слоеного теста с
сыром (на 2-ух уровнях)
Эклеры (на 3-х уровнях)
Печенье (на 3-х уровнях)
Безе (на 3-х уровнях)
0.5
1
0.7
0.5
1.2
0.6
0.4
0.7
0.7
0.5
3
2 или 3
3
3
2 и 4
2 и 4
2 и 4
1 и 3 и 5
1 и 3 и 5
1 и 3 и 5
15
15
15
15
15
15
15
15
15
15
180
180
180
160
200
190
210
180
180
90
20-30
40-45
40-50
25-30
30-35
20-25
15-20
20-25
20-25
180
20
RS
Варочная панель,
Модели варочной панели
Духовой шкаф соединен с варочной
панелью, которая может иметь два
вида нагревательных элементов:
чугунные электрические конфорки
(см. рисунок 1) или
стеклокерамические конфорки,
которые могут быть
традициональными ( см. рисунок 2) с
расширяющимися варочными зонами ( см. рисунок 3).
Включение стеклокерамической
варочной панели
Традициональные конфорки
Традициональные нагревательные элементы (А)
состоят из круглых спиралей, раскаляющихся
докрасна только по прошествии нескольких десятков
секунд после их включения.
Каждая конфорка управляется регулятором,
позволяющим выбрать 9 различных температур от
минимального значения 1 до максимального 9.
Расширяющиеся конфорки
Расширяющиеся нагревательные элементы (В)
отличаются наличием двойной нагревательной зоны.
Можно включить только внутреннюю часть конфорки
или обе.
Регулятор позволяет выбрать один из двух уровней
мощности, оба из которых настраиваются от
минимального значения 1 до максимального 9.
поворачивая регулятор по часовой стрелки с 1 на 9,
задается более низкий уровень мощности.
повернув регулятор до упора (
AA
AA
A), что заметно по
легкому щелчку, подключается максимальная
мощность, которая может быть в свою очередь
отрегулирована от 9 до 1, поворачивая регулятор
против часовой стрелки. Для возврата к
минимальной мощности необходимо повернуть
регулятор в положение 0.
В случае двойных конфорок первая часть поворота
регулятора включает меньшую зону (внутреннюю).
Для включения обеих зон (внутренней и внешней)
необходимо повернуть регулятор до упора (
AA
AA
A) и
выбрать нужный уровень мощности от 9 до 1.
Индикаторы остаточного тепла (имеются только в
некоторых моделях)
Индикаторы (С) показывают, что температура
соответствующей конфорки выше 60°C даже после
отключения нагревательного элемента.
Рекомендуемые уровни мощности для различных
типов приготовления:
Практические рекомендации по
использованию стеклокерамической
варочной панели
! На стеклянной поверхности варочной панели могут
быть видны сальные следы от клея, нанесенного на
прокладки Перед началом эксплуатации изделия
следует удалить следы клея при помощи
специального неабразивного моющего средства. В
первые часы работы вы можете почувствовать запах
жженой резины, который быстро пропадает.
Для оптимальной эксплуатации варочной панели следует:
• спользовать посуду с плоским дном, идеально
прилегающим к зоне нагревания.
использовать кастрюли с дном такого диаметра,
чтобы полностью закрыть зону нагревания для
оптимального использования всего выделяемого
тепла.
проверить, чтобы дно используемой посуды было
всегда совершенно сухим и чистым для идеального
прилегания к конфорке и для долгого срока службы
как варочной панели, так и самой посуды.
не следует использовать ту же посуду,
использованную на газовых конфорках:
концентрация тепла на газовых конфорках может
деформировать дно посуды и нарушить прилегание
к нагревательной зоне;
никогда не оставлять какую-либо зону нагревания
включенной, не поместив на нее посуду, так как она
быстро достигает максимального нагрева, что
может повредить нагревательные элементы.
C
A
A
A
A
рисунок 3
C
A
A
B
B
рисунок 1
рисунок 2
Мощность
Электрическая конфорка
0 Выключено
1
Для растапливания сливочного
масла или шоколада
2 и 3 Нагрев жидкостей
4 Приготовление кремов или соусов
5 Вареное мясо
6
Приготовление макаронных изделий
или риса
7 и 8
Приготовления на сильном огне
мяса, рыбы, омлетов
9 Фритюр
A
Включение обеих зон нагревания
1 / 1

Indesit 7OHH 627 IXRU/HA Руководство пользователя

Категория
Кухонные плиты (варочные панели)
Тип
Руководство пользователя

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ

Спросите документ

на других языках