Yamaha Clavinova CLP-320 Инструкция по применению

Категория
Дополнительное музыкальное оборудование
Тип
Инструкция по применению

Это руководство также подходит для

EN
CLP-320
OWNER’S MANUAL
IMPORTANT
—Check your power supply—
Make sure that your local AC mains voltage matches the voltage specified on the name plate on the bottom panel. In some areas a voltage selector may
be provided on the bottom panel of the main keyboard unit near the power cord. Make sure that the voltage selector is set for the voltage in your area.
The voltage selector is set at 240V when the unit is initially shipped. To change the setting use a "minus" screwdriver to rotate the selector dial so that the
correct voltage appears next to the pointer on the panel.
For information on assembling the keyboard stand, refer to the instructions at the end of this manual.
ENGLISH
CLP-320
Owner’s Manual
2
Introduction
92-469
1
(bottom)
SPECIAL MESSAGE SECTION
PRODUCT SAFETY MARKINGS:
Yamaha electronic
products may have either labels similar to the graphics
shown below or molded/stamped facsimiles of these
graphics on the enclosure. The explanation of these
graphics appears on this page. Please observe all cautions
indicated on this page and those indicated in the safety
instruction section.
See bottom of Keyboard enclosure for graphic symbol markings.
The exclamation point within the
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servic-
ing) instructions in the literature
accompanying the product.
The lightning flash with arrowhead
symbol, within the equilateral trian-
gle, is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product’s enclo-
sure that may be of sufficient magni-
tude to constitute a risk of electrical
shock.
IMPORTANT NOTICE:
All Yamaha electronic products
are tested and approved by an independent safety testing
laboratory in order that you may be sure that when it is
properly installed and used in its normal and customary
manner, all foreseeable risks have been eliminated. DO
NOT modify this unit or commission others to do so
unless specifically authorized by Yamaha. Product perfor-
mance and/or safety standards may be diminished.
Claims filed under the expressed warranty may be denied
if the unit is/has been modified. Implied warranties may
also be affected.
SPECIFICATIONS SUBJECT TO CHANGE:
The
information contained in this manual is believed to be
correct at the time of printing. However, Yamaha reserves
the right to change or modify any of the specifications
without notice or obligation to update existing units.
ENVIRONMENTAL ISSUES:
Yamaha strives to pro-
duce products that are both user safe and environmentally
friendly. We sincerely believe that our products and the
production methods used to produce them, meet these
goals. In keeping with both the letter and the spirit of the
law, we want you to be aware of the following:
Battery Notice:
This product MAY contain a small non-
rechargable battery which (if applicable) is soldered in
place. The average life span of this type of battery is
approximately five years. When replacement becomes
necessary, contact a qualified service representative to
perform the replacement.
Warning:
Do not attempt to recharge, disassemble, or
incinerate this type of battery. Keep all batteries away
from children. Dispose of used batteries promptly and as
regulated by applicable laws. Note: In some areas, the
servicer is required by law to return the defective parts.
However, you do have the option of having the servicer
dispose of these parts for you.
Disposal Notice:
Should this product become damaged
beyond repair, or for some reason its useful life is consid-
ered to be at an end, please observe all local, state, and
federal regulations that relate to the disposal of products
that contain lead, batteries, plastics, etc.
NOTICE:
Service charges incurred due to lack of knowl-
edge relating to how a function or effect works (when the
unit is operating as designed) are not covered by the man-
ufacturer’s warranty, and are therefore the owners respon-
sibility. Please study this manual carefully and consult
your dealer before requesting service.
NAME PLATE LOCATION:
The graphic below indi-
cates the location of the name plate. The model number,
serial number, power requirements, etc., are located on
this plate. You should record the model number, serial
number, and the date of purchase in the spaces provided
below and retain this manual as a permanent record of
your purchase.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Model
Serial No.
Purchase Date
CLP-320
ENGLISH
CLP-320
Owner’s Manual
3
The above warning is located on the bottom side of the unit.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand,
tripod, bracket, or table specified
by the manufacturer, or sold with
the apparatus. When a cart is
used, use caution when moving
the cart/apparatus combination
to avoid injury from tip-over.
13 Unplug this apparatus during
lightning storms or when unused for long periods of
time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
(UL60065_03)
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
1
ENGLISH
CLP-320
Owner’s Manual
4
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Only use the voltage specified as correct for the instrument. The required
voltage is printed on the name plate of the instrument.
Check the electric plug periodically and remove any dirt or dust which may have
accumulated on it.
Use only the supplied power cord/plug.
Do not place the power cord near heat sources such as heaters or radiators, and
do not excessively bend or otherwise damage the cord, place heavy objects on
it, or place it in a position where anyone could walk on, trip over, or roll anything
over it.
Do not open the instrument or attempt to disassemble the internal parts or
modify them in any way. The instrument contains no user-serviceable parts. If it
should appear to be malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
Do not expose the instrument to rain, use it near water or in damp or wet
conditions, or place containers on it containing liquids which might spill into
any openings. If any liquid such as water seeps into the instrument, turn off the
power immediately and unplug the power cord from the AC outlet. Then have
the instrument inspected by qualified Yamaha service personnel.
Never insert or remove an electric plug with wet hands.
Do not put burning items, such as candles, on the unit.
A burning item may fall over and cause a fire.
If the power cord or plug becomes frayed or damaged, or if there is a sudden
loss of sound during use of the instrument, or if any unusual smells or smoke
should appear to be caused by it, immediately turn off the power switch,
disconnect the electric plug from the outlet, and have the instrument inspected
by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the instrument or other property. These precautions include, but are not limited to, the following:
When removing the electric plug from the instrument or an outlet, always hold
the plug itself and not the cord. Pulling by the cord can damage it.
Remove the electric plug from the outlet when the instrument is not to be used
for extended periods of time, or during electrical storms.
Do not connect the instrument to an electrical outlet using a multiple-connector.
Doing so can result in lower sound quality, or possibly cause overheating in the
outlet.
Read carefully the attached documentation explaining the assembly process.
Failure to assemble the instrument in the proper sequence might result in
damage to the instrument or even injury.
Do not expose the instrument to excessive dust or vibrations, or extreme cold or
heat (such as in direct sunlight, near a heater, or in a car during the day) to
prevent the possibility of panel disfiguration or damage to the internal
components.
Do not use the instrument in the vicinity of a TV, radio, stereo equipment,
mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio
may generate noise.
Do not place the instrument in an unstable position where it might accidentally
fall over.
Before moving the instrument, remove all connected cables.
When setting up the product, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn off
the power switch and disconnect the plug from the outlet. Even when the power
switch is turned off, electricity is still flowing to the product at the minimum
level. When you are not using the product for a long time, make sure to unplug
the power cord from the wall AC outlet.
Power supply/Power cord
Do not open
Water warning
Fire warning
If you notice any abnormality
Power supply/Power cord
Assembly
Location
2
(1)B-12
1/2
ENGLISH
CLP-320
Owner’s Manual
5
Before connecting the instrument to other electronic components, turn off the
power for all components. Before turning the power on or off for all
components, set all volume levels to minimum. Also, be sure to set the volumes
of all components at their minimum levels and gradually raise the volume
controls while playing the instrument to set the desired listening level.
In the case of a model with a polished finish, gently remove dust and dirt with a
soft cloth. Do not wipe too hard since small particles of dirt can scratch the
instrument’s finish.
When cleaning the instrument, use a soft,dry or slightly damp cloth. Do not use
paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping
cloths.
•Take care that the key cover does not pinch your fingers, and do not insert a
finger or hand in any gaps on the key cover or instrument.
Never insert or drop paper, metallic, or other objects into the gaps on the key
cover, panel or keyboard. If this happens, turn off the power immediately and
unplug the power cord from the AC outlet. Then have the instrument inspected
by qualified Yamaha service personnel.
Do not place vinyl, plastic or rubber objects on the instrument, since this might
discolor the panel or keyboard.
In the case of a model with a polished finish, bumping the surface of the
instrument with metal, porcelain, or other hard objects can cause the finish to
crack or peel. Use caution.
Do not rest your weight on, or place heavy objects on the instrument, and do not
use excessive force on the buttons, switches or connectors.
Do not use the instrument/device or headphones for a long period of time at a
high or uncomfortable volume level, since this can cause permanent hearing
loss. If you experience any hearing loss or ringing in the ears, consult a
physician.
Do not place the bench in an unstable position where it might accidentally fall
over.
Do not play carelessly with or stand on the bench. Using it as a tool or step-
ladder or for any other purpose might result in accident or injury.
Only one person should sit on the bench at a time, in order to prevent the
possibility of accident or injury.
If the bench screws become loose due to extensive long-term use, tighten them
periodically using the included tool.
Saving and backing up your data
Data in the instrument’s internal memory can be lost due to operational errors or
malfunction. Be sure to save any important data to external media via a
computer connected to the instrument. (page 31)
Always turn the power off when the instrument is not in use.
Even when the power switch is turned off, electricity is still flowing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure
you unplug the AC power plug from the wall AC outlet.
Connections
Maintenance
Handling caution
Using the bench (If included)
Saving data
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.
3
(1)B-12
2/2
Welcome
CLP-320
Owner’s Manual
6
ENGLISH
Welcome
Thank you for purchasing the Yamaha Clavinova! We recommend that you read this manual carefully so that you can take
full advantage of the advanced and convenient functions of your new Clavinova.
We also recommend that you keep this manual in a safe, convenient place for future reference.
About the Documentation and Refer-
ence Materials for this Instrument
The documentation and reference materials for this instrument consist of the following:
Owner’s Manual (this book)
Introduction (P2):
Please read this section first.
Reference (P15):
This section explains how to make detailed settings for the instrument’s various functions.
Appendix (P40):
This section introduces specifications and other information.
Quick Operation Guide (separate sheet)
This Guide explains detailed operation of the functions assigned to the buttons and keyboard.
Data List
You can download various MIDI-related reference materials, such as the MIDI Data Format and MIDI Implementa-
tion Chart, from the
Yamaha Manual Library
.
Connect to the Internet, visit the following website, type the model name of your instrument (such as “CLP-320”) in
the Model Name text box, then click the Search button.
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
•The illustrations as shown in this owner’s manual are for instructional purposes only, and may be different from the
ones on your instrument.
Trademarks:
•Windows is a registered trademark of Microsoft® Corporation in the United States and other countries.
•The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with
respect to which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all
computer software, style files, MIDI files, WAVE data, musical scores and sound recordings. Any unauthorized use of
such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright
has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.
Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is
strictly prohibited except for your personal use.
4
Accessories
CLP-320
Owner’s Manual
7
ENGLISH
Accessories
Owner’s Manual (this book)
Quick Operation Guide (separate sheet)
“50 Greats for the Piano” (Music Book)
AC Power cord
Bench*
* Included or optional depending on locale.
Tuning
Unlike an acoustic piano, this instrument does not need to be tuned. It always stays perfectly in tune.
Transporting
If you move to another location, you can transport this instrument along with your other belongings. You can move
the unit as it is (assembled) or you can disassemble the unit before moving.
Tr ansport the keyboard horizontally. Do not lean it up against a wall or stand it up on its side. Do not subject the
instrument to excessive vibration or shock.
5
Features
CLP-320
Owner’s Manual
8
ENGLISH
Features
AWM Dynamic Stereo Sampling
The Yamaha Clavinova CLP-320 digital piano offers a rich and versatile range of sounds, which are created using
Yamahas proprietary sampling tone-generation system, AWM Dynamic Stereo Sampling.
The AWM (Advanced Wave Memory) is a sampling system which creates sound close to that of an acoustic instru-
ment by using digital technology to record the instrument sound and applying high-quality digital filter technology
to the recorded audio samples.
The waveform of the sound created by playing the key of an acoustic piano differs depending on the playing
strength from pianissimo to fortissimo. The AWM Dynamic Stereo Sampling can produce such dynamic nuances by
recording samples of various playing strengths. The greater the number of samples used, the higher the expressive
quality and potential becomes.
The piano voice “Grand Piano 1” , features totally new sample recorded from a full-size concert grand piano. Each
note in the sample has been adjusted meticulously so that the digital piano will play only the very best piano sounds.
The piano voices are well-separated sounds featuring a fast attack and a satisfying response.
The “Grand Piano 1” voice features multiple wave samples for different velocities (Dynamic Sampling); that is, dif-
ferent samples are used depending on how fast or strong you strike the keys. Therefore, this voice expresses detailed
dynamics and sounds much closer to a true acoustic piano.
GH(Graded Hammer) keyboard
A special Graded Hammer keyboard on the CLP-320, features graded key weight and response throughout the key-
board range. They respond to a heavier touch in the low range of the keyboard and a lighter touch in the higher
range of the keyboard, thus providing natural grand-piano type playability. The matte finish of the black keys
enhances keyboard’s luxurious appearance. The Graded Hammer keyboard also offers superb playability for trem-
olo and other repetitive-striking techniques.
6
Table of Contents
CLP-320
Owner’s Manual
9
ENGLISH
Table of Contents
Introduction
SPECIAL MESSAGE SECTION ...................... 2
About the Documentation and Reference
Materials for this Instrument...................... 6
Accessories .................................................. 7
Features....................................................... 8
Part Names and Functions........................ 10
Before Using.............................................. 12
Key Cover ..........................................................12
Music Rest .........................................................12
Connecting the Power Cord.............................13
Turning the Power On......................................13
Setting the Volume............................................14
Using Headphones............................................14
Reference
Listening to the Demo Songs ................... 15
Listening to 50 Piano Preset Songs .......... 16
Listening to Songs Loaded from the
Computer .................................................. 17
Selecting & Playing Voices........................ 18
Selecting Voices.................................................18
Using the Pedals ................................................19
Adding Variations to the Sound – Reverb.......20
Layering Two Voices (Dual mode) ..................21
Transposition ....................................................22
Fine-tuning the Pitch........................................22
Using the Metronome.......................................23
Adjusting the Keyboard Touch (Touch
Sensitivity) .........................................................24
Recording your Performance.................... 25
Playing Back Recorded Performance Data ......26
Erasing Recorded Performance Data ...............26
Connecting MIDI Instruments .................. 27
About MIDI ...................................................... 27
MIDI’s Capability ............................................. 27
Connecting a Computer ...........................28
MIDI Functions ..........................................29
MIDI Transmit/Receive Channel Selection .... 29
Local Control ON/OFF .................................... 29
Program Change ON/OFF............................... 30
Control Change ON/OFF ................................ 30
Transmitting Song Data between the
Computer and the Clavinova.................... 31
Loading Song Data from a Computer to the
Clavinova .......................................................... 31
Transmitting Song Data from the Clavinova to a
Computer.......................................................... 32
Backing up Data and Initializing the Settings. 32
Troubleshooting........................................ 33
Options...................................................... 33
Keyboard Stand Assembly ........................34
Index.......................................................... 38
Appendix
Specifications ............................................40
7
Part Names and Functions
CLP-320
Owner’s Manual
10
ENGLISH
Part Names and Functions
POWER
PHONES
[DEMO/SONG]
Listen to the playback of a demo song for each
voice and 50 piano preset songs (page 15).
[METRONOME]
Control the metronome functions (page 23).
[REC]
Record your performance (page 25).
[PLAY]
Play back your recorded performance (page 26).
[MASTER VOLUME]
Adjust the volume level using this control (page 14).
[+]/[–]
These buttons enable you to select a song to play
back from voice demo songs or from “50 Greats
for the Piano. (pages 15, 16)
They also enable you to change the voice or
tempo. (pages 18, 23)
[PIANO/VOICE]
This button enables you to select any voice from
10 voices. (page 18)
You can also layer two voices (page 21), or select a
type of reverb (page 20).
[PHONES]
A set of standard stereo headphones can be
plugged in here for private practice (page 14).
[POWER]
This power switch turns the power to the
unit on or off. (page 13)
Bottom of the keyboard
8
Part Names and Functions
CLP-320
Owner’s Manual
11
ENGLISH
MIDI
INOUT
PEDAL
POWER
[PEDAL]
Connect the pedal cord (page 36).
MIDI [IN/OUT]
Connect a MIDI device to this connector to
use various MIDI functions.
(Connecting MIDI Instruments—page 27)
Shows the MIDI [IN/OUT] and [PEDAL]
jacks as seen when viewed from the rear of
the instrument.
[AC IN]
Connect the included power cord here.
(page 13)
Pedals
Use these pedals when you want notes to
sustain longer or to sound softer and round.
(Using the Pedals—page 19)
Bottom of the keyboard
9
Before Using
CLP-320
Owner’s Manual
12
ENGLISH
Before Using
Key Cover
To open the key cover:
Lift the cover slightly, then push and slide it
open.
To close the key cover:
Slide the cover toward you and gently lower the
cover over the keys.
CAUTION
Hold the cover with both hands when opening or
closing it. Do not release it until it is fully opened or
closed. Be careful to avoid catching fingers (yours or
others, especially children’s) between the cover and
main unit.
CAUTION
Do not place objects, such as a piece of metal or paper, on top of the key cover. Small objects placed on the key cover
may fall inside the unit when the cover is opened and may be nearly impossible to remove. This could cause electric
shock, short circuit, fire or other serious damage to the instrument.
If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the instrument
inspected by qualified Yamaha service personnel.
Music Rest
To raise the music rest:
1. Pull the music rest up and toward yourself as far as it will
go.
2. Flip down the two metal supports at the left and right on
the rear of the music rest.
3. Lower the music rest so that it rests on the metal sup-
ports.
To lower the music rest:
1. Pull the music rest toward yourself as far as it will go.
2. Raise the two metal supports (at the rear of the music
rest).
3. Gently lower the music rest backward until it is all the
way down.
CAUTION
Do not try to use the music rest in a half-raised position.
When lowering the music rest, do not release your hands
from the music rest until it is all the way down.
CAUTION
Be careful to avoid catching your fingers
when opening or closing the cover.
10
Before Using
CLP-320 Owner’s Manual
13
ENGLISH
Connecting the Power Cord
Read the instructions below very carefully to make sure that you correctly connect the power cord.
1. Insert the plug on one end of the power cord to the [AC IN] connector. Refer to the “Part Names and
Functions” on page 11 for information on the location of the [AC IN] connector.
2. Insert the plug on the other end of the power cord to a standard AC outlet.
(The shape of the plug differs depending on locale.)
WARNING
Make sure your Clavinova is rated for the AC voltage supplied in the area in which the piano will be used. (The voltage rating appears on
the name plate on the bottom panel). In some areas, a voltage selector may be provided on the bottom panel of the main keyboard unit
near the power cord. Make sure that the voltage selector is set for the voltage in your area. Connecting the unit to an inappropriate AC
supply can seriously damage the internal circuitry and may even pose a shock hazard!
Use only the AC power cord supplied with the instrument. If the supplied power cord is lost or damaged and needs to be replaced, contact
your Yamaha dealer. The use of an inappropriate replacement can pose a fire and shock hazard!
The type of AC power cord provided with the instrument may be different depending on the country in which the instrument was pur-
chased. (In some areas a plug adaptor may be provided to match the pin configuration of the AC wall outlets in your area.)
Do NOT modify the plug provided with the instrument. If the plug will not fit the outlet, have a proper outlet installed by a qualified electri-
cian.
Turning the Power On
Press the [POWER] switch on the right end of the keyboard to turn on the power to the unit.
The power indicator located below the left end of the keyboard lights up.
Press the [POWER] switch again to turn off the power to the unit.
The power indicator turns off.
Power indicator
If you forget to turn off the power to the piano and close the key cover, the power indicator will remain lit, indicating that
the power is still on.
CAUTION
A small amount of electrical current remains even after the power switch is turned off. If you plan not to use the instru-
ment for a long period of time, be sure to unplug the instrument from the AC outlet.
12
(Bottom of the
keyboard)
Power indicator
[POWER]
11
Before Using
CLP-320 Owner’s Manual
14
ENGLISH
Setting the Volume
When you start playing, adjust the [MASTER VOLUME] control to the most comfortable listening level.
CAUTION
Do not use this instrument at a high volume level for a long period of time, or your hearing may be damaged.
Using Headphones
Connect a pair of headphones to one of the [PHONES] jacks.
Two [PHONES] jacks are provided.
You can connect two sets of standard stereo headphones. (If you are
using only one pair of headphones, you can plug them into either
jack.)
CAUTION
Do not listen to the instrument at a high volume level through head-
phones for a long period of time, or your hearing may be damaged.
Using the Headphone Hanger
A headphone hanger is included in the package so that you can hang the head-
phones on this instrument. Install the headphone hanger using the included
two screws (4 × 10mm) as shown in the figure.
CAUTION
Do not hang anything other than the headphones on the hanger. Otherwise,
this instrument or the hanger may be damaged.
The level decreases. The level increases.
PHONES
Bottom of the keyboard
Standard stereo
phone plug
PHONES
12
Listening to the Demo Songs
CLP-320 Owner’s Manual
15
ENGLISH
13
Listening to the Demo Songs
Demo songs are provided that effectively demonstrate each of this instrument’s voices.
Refer to the voice list on
page 18 for more information on
the characteristics of each pre-
set voice.
1. Turn on the power.
While a demo song is playing,
press and hold down the [MET-
RONOME] button and press the
[+] or [–] button to change the
song tempo.
If you are using the metronome
(page 23) during demo song
playback, press the [+] or [–]
button to change the song
tempo.
You can also press keys to
change the tempo. (page 23)
The demo songs will not be
transmitted via MIDI.
You can also change to the next
or previous demo song by
pressing and holding down the
[DEMO/SONG] button and
pressing the [+] or [–] button.
Adjusting the Volume
Use the [MASTER VOLUME]
control to adjust the volume.
(In case the power is not turned on) Press the [POWER] button.
2. Start playing back a demo song.
Press the [DEMO/SONG] button.
The demo song for the currently-selected voice starts playing.
3. Select and play a demo song.
While a demo song is playing, press the [+] or [–] button to select and play the
next or previous demo song.
If you wish to select a particular demo song from 10 voice demo songs, press
and hold down the [DEMO/SONG] button, then press one of the C1–A1 keys.
The selected demo song starts to play. Starting with the selected song, the
playback of the demo songs will continue in the following sequence: other
voice demo songs, followed by 50 piano preset songs, and any songs
loaded from the computer. The sequence then returns to the first demo
song and repeats until you stop it.
Demo Songs
Each of the 10 voices features its own demo song that showcases the corre-
sponding voice. Please refer to “Selecting Voices on page 18.
The demo songs listed below are re-arranged excerpts from the original compo-
sitions.
The other demo songs are Yamaha’s original pieces (©2008 Yamaha Corpora-
tion).
4. Stop the Voice demo.
Press the [DEMO/SONG] button to stop playback.
Procedure
C1 A1
The lowest key
Key Voice Name Title Composer
C1 GRAND PIANO 1 Albumbrad, Lyriske stykker IV, op.47-2 E. H. Grieg
E1 HARPSICHORD 1 Concerto a cembalo obbligato, 2 violini, viola e continuo No.7, BWV.1058 J. S. Bach
F1 HARPSICHORD 2 Gigue, Französische Suiten Nr.5, BWV.816 J. S. Bach
G1 CHURCH ORGAN 1 Herr Christ, der ein’ge Gottes-Sohn, BWV.601 J. S. Bach
G
1 CHURCH ORGAN 2 Triosonate Nr.6, BWV.530 J. S. Bach
Reference
Listening to 50 Piano Preset Songs
CLP-320 Owner’s Manual
16
ENGLISH
Listening to 50 Piano Preset Songs
The Clavinova provides performance data for 50 piano songs as well as voice demo songs. You can
simply listen to these songs. You can also refer to the included “50 Greats for the Piano” that con-
tains scores for 50 piano preset songs.
1. Select and play back a piano preset song.
You can play the keyboard
along with the preset song. You
can change the voice playing on
the keyboard.
The default tempo is automati-
cally selected whenever a new
preset song is selected, and
when a new preset song begins
playback.
While a piano preset song is
playing, hold down the [MET-
RONOME] button and press the
[+] or [–] button to change the
song tempo.
If you are using the metronome
(page 23) during preset song
playback, press the [+] or [–]
button to change the song
tempo.
You can also press keys to
change the tempo. (page 23)
When you select a different
song (or a different song is
selected during chained play-
back), an appropriate reverb
type will be selected accord-
ingly.
The 50 piano preset songs will
not be transmitted via MIDI.
The number of each piano preset song is assigned to the C2–C
6 keys.
While holding down the [DEMO/SONG] button, press one of the C2–C
6 keys
to select a song to play back.
The selected piano song starts to play.
To play all preset songs consecutively in sequence, while holding down the
[DEMO/SONG] button, press the D6 key.
While a piano preset song is playing, press the [+] or [–] button to change to the
next or previous piano song.
Adjusting the Volume
Use the [MASTER VOLUME] control to adjust the volume.
2. Stop playback.
To stop the song during playback (or continuous playback), press the [DEMO/
SONG]
button.
•To continue playing other songs, see procedure 1 above.
Procedure
Song:
On this instrument, perfor-
mance data is called a
“Song.This includes demo
songs and 50 piano preset
tunes.
C2 C4C3 C5
The highest
key (C7)
Consecutive
playback
(D6)
1st song 10th song 20th song 30th song 40th song 50th song (C
6)
14
Listening to Songs Loaded from the Computer
CLP-320 Owner’s Manual
17
ENGLISH
Listening to Songs Loaded from the
Computer
You can transfer song data from your computer to this instrument and play back the songs. (See
page 31 for more information on loading song data from the computer.)
1. Select and play back a song.
You can load up to 10 songs or
up to 337 KB of data from the
computer.
Songs loaded from the com-
puter will be numbered auto-
matically.
Use the following table to write
down the song titles you loaded
from the computer.
Song numbers (1 through 10) are assigned to the D
6–C7 keys (see the illustra-
tion below).
While holding down the [DEMO/SONG] button, press one of the D
6–C7 keys
to select a song to play back.
The selected song starts to play.
Adjusting the Volume
Use the [MASTER VOLUME] control to adjust the volume while listening to the
song.
2. Stop playback.
To stop the song during playback, press the [DEMO/SONG] button.
Selecting a Song Playback Channel
If a song loaded from the computer uses a voice that is not supported by this
instrument, the originally-assigned voice may not be reproduced accurately. In
this case, switching the song playback channel from All” to “1 + 2” may
improve the tone to more natural sound.
Selecting 1 + 2 song playback channels:
While pressing and holding down the
[DEMO/SONG] button and the [PIANO/
VOICE]
button simultaneously, press the C7 key.
Channels 1 + 2 will produce the sound.
Selecting all song playback channels:
While pressing and holding down the [DEMO/SONG] button and the [PIANO/
VOICE]
button simultaneously, press the B6 key.
All channels 1 through 16 will produce the sound.
Procedure
Key Song title
D
6
E6
F6
F
6
G6
G
6
A6
A
6
B6
C7
C7
D 6
1st song 10th song
(The highest key)
C7
The highest key
B6
The highest key
15
Selecting & Playing Voices
CLP-320 Owner’s Manual
18
ENGLISH
Selecting & Playing Voices
Selecting Voices
To understand the characteris-
tics of various voices, listen to
demo songs for each voice
(page 15).
Press and release the [PIANO/VOICE] button to select the Grand Piano 1 voice.
Press and release the [PIANO/VOICE] button, press the [+] or [–] button to select a dif-
ferent voice.
Selecting a voice automatically
engages the best-suited reverb
type and depth (page 20) for
that particular voice.
If you wish to select a particular voice directly, press and hold down the [PIANO/
VOICE]
button, then press one of the C1–A1 keys.
Turn the [MASTER VOLUME] control to adjust the volume level while playing the key-
board.
Procedure
Voice:
On this instrument, a voice
means a “tone” or “tonal
color.
Key Voice Name Description
C1 Grand Piano 1 Recorded samples from a full concert grand piano. Perfect for classical
compositions as well as any other style that requires acoustic piano.
C
1Grand Piano 2 Spacious and clear piano with bright reverb. Good for popular music.
D1 E.Piano 1
An electronic piano sound created by FM synthesis. Good for popular music.
D
1 E.Piano 2 The sound of an electric piano using hammer-struck metallic “tines. Soft
tone when played lightly, and an aggressive tone when played hard.
E1 Harpsichord 1 The definitive instrument for baroque music. Since the strings of a harpsi-
chord are plucked, there is no touch response.
F1 Harpsichord 2 Mixes the same voice an octave higher for a more brilliant tone.
F
1 Vibraphone The sound of a vibraphone played with relatively soft mallets.
G1 Church Organ 1 This is a typical pipe organ sound (8 feet + 4 feet + 2 feet). Good for
sacred music from the Baroque period.
G
1 Church Organ 2 This is the organ’s full coupler sound, often associated with Bach’s “Toc-
cata and Fugue”.
A1 Strings Spacious and large-scale string ensemble. Try combining this voice with
piano in DUAL mode.
C1 D1 E1 F1 G1 A1
C 1
D 1
F 1
G 1
The lowest key
16
Selecting & Playing Voices
CLP-320 Owner’s Manual
19
ENGLISH
Using the Pedals
If the damper pedal doesn’t
work, make sure that the pedal
cord is properly plugged into the
main unit (page 36).
Organ and string voices will
continue to sound for as long as
the sostenuto pedal is
depressed.
Damper (Right) Pedal
The damper pedal functions in the same way as a
damper pedal on an acoustic piano. When the
damper pedal is pressed, notes sustain longer.
Releasing the pedal immediately stops (damps) any
sustained notes.
The damper pedal features a half-pedal function.
Sostenuto (Center) Pedal
If you play a note or chord on the keyboard and
press the sostenuto pedal while the note(s) are
held, those notes will sustain as long as you hold
the pedal (as if the damper pedal had been pressed)
but all subsequently played notes will not be sus-
tained. This makes it possible to sustain a chord,
for example, while other notes are played “stac-
cato.
Soft (Left) Pedal
The soft pedal reduces the volume and slightly changes the timbre of notes played while
the pedal is pressed. The soft pedal will not affect notes that are already playing when it
is pressed.
What is the half-pedal
function?
This function allows the sus-
tain length to vary depend-
ing on how far the pedal is
pressed. The farther you
press the pedal, the more
the sound sustains.
For example, if you press the
damper pedal and all notes
you are playing sound a bit
murky and loud with too
much sustain, you can
release the pedal half way to
subdue the sustain (murki-
ness).
When you press the damper pedal
here, the notes you play before you
release the pedal sustain longer.
When you press the sostenuto pedal
here while holding the note, the note
will sustain as long as you hold the
pedal.
17
Selecting & Playing Voices
CLP-320 Owner’s Manual
20
ENGLISH
Adding Variations to the Sound – Reverb
This control enables you to select various digital reverb effects that add extra depth and expression
to the sound to create a realistic acoustic ambience.
While holding down the [PIANO/VOICE] button, press one of the C2–E2 keys to select
a reverb type.
Adjusting Reverb Depth
The default reverb type (includ-
ing OFF) and depth settings are
different for each voice.
depth 0: no effect
depth 20: maximum reverb
depth
Adjust the reverb depth for the selected voice by pressing one of the C3–G
4 keys while
holding down the [PIANO/VOICE] button. The depth range is from 0 through 20.
While holding down the [PIANO/VOICE] button, press the A4 key to set the reverb to
the depth most suitable for the selected voice.
Procedure
Key Reverb Type Description
C2 Room This setting adds a continuous reverb effect to the sound, similar to
the acoustic reverberation you would hear in a room.
C
2 Hall1 For a “bigger” reverb sound, use the HALL 1 setting. This effect simu-
lates the natural reverberation of a small-size concert hall.
D2 Hall2 For a truly spacious reverb sound, use the HALL 2 setting. This effect
simulates the natural reverberation of a large concert hall.
D
2 Stage Simulates the reverb of a stage environment.
E2 Off No effect is applied.
C2 D2 E2
C 2
D 2
The lowest key
The depth value increases as you press higher keys.
A4
The lowest key C3: depth 0
G
4: depth 20
18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Yamaha Clavinova CLP-320 Инструкция по применению

Категория
Дополнительное музыкальное оборудование
Тип
Инструкция по применению
Это руководство также подходит для

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ