Yamaha MSR250 Руководство пользователя

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

POWERED SPEAKER

MSR250

MSR250 Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in

this manual, meets FCC requirements. Modiﬁcations not expressly

approved by Yamaha may void your authority, granted by the FCC, to

use the product.

2. IMPORTANT:

When connecting this product to accessories and/or

another product use only high quality shielded cables. Cable/s supplied

with this product MUST be used. Follow all installation instructions. Fail-

ure to follow instructions could void your FCC authorization to use this

product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reasonable

level of assurance that your use of this product in a residential environ-

ment will not result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed

and used according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

will not occur in all installations. If this product is found to be the source

of interference, which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being affected by the

interference.

Utilize power outlets that are on different branch (circuit breaker or fuse)

circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If

the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-

axial type cable.

If these corrective measures do not produce satisfactory results, please

contact the local retailer authorized to distribute this type of product. If

you can not locate the appropriate retailer, please contact Yamaha Cor-

poration of America, Electronic Service Division, 6600 Orangethorpe

Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING:

THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accordance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug

proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth

symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (3 wires)

The above warning is located on the bottom and rear of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol within an

equilateral triangle is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufﬁcient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliﬁers) that

produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type

plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety. If the

provided plug does not ﬁt into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly

at plugs, convenience receptacles, and the point where they exit

from the apparatus.

11 Only use attachments/accessories speciﬁed by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or

table speciﬁed by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualiﬁed service

personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged,

liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

ENGLISH

MSR250 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not

limited to, the following:

• Only use the voltage speciﬁed as correct for the device. The required

voltage is printed on the name plate of the device.

• Use only the included power cord.

• Do not place the power cord near heat sources such as heaters or

radiators, and do not excessively bend or otherwise damage the cord,

place heavy objects on it, or place it in a position where anyone could

walk on, trip over, or roll anything over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• Do not open the device or attempt to disassemble the internal parts or

modify them in any way. The device contains no user-serviceable parts.

If it should appear to be malfunctioning, discontinue use immediately

and have it inspected by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might

spill into any openings. If any liquid such as water seeps into the

device, turn off the power immediately and unplug the power cord from

the AC outlet. Then have the device inspected by qualiﬁed Yamaha

service personnel.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the device, or if any unusual smells

or smoke should appear to be caused by it, immediately turn off the

power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualiﬁed Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the

power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or

damage to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be

used for extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always

hold the plug itself and not the cord. Pulling by the cord can damage it.

• Always consult qualiﬁed Yamaha service personnel if the device

installation requires construction work, and make sure to observe the

following precautions.

- Choose mounting hardware and an installation location that can support

the weight of the device.

-Avoid locations that are exposed to constant vibration.

- Inspect the device periodically.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using

is easily accessible. If some trouble or malfunction occurs, immediately

turn off the power switch and disconnect the plug from the outlet. Even

when the power switch is turned off, electricity is still ﬂowing to the

product at the minimum level. When you are not using the product for a

long time, make sure to unplug the power cord from the wall AC outlet.

• Do not use the device in a conﬁned, poorly-ventilated location. Make

sure that there is adequate space between the device and surrounding

walls or other devices: at least 30cm at the sides, 30cm behind and

30cm above. Inadequate ventilation can result in overheating, possibly

causing damage to the device(s), or even ﬁre.

• Do not expose the device to excessive dust or vibrations, or extreme

cold or heat (such as in direct sunlight, near a heater, or in a car during

the day) to prevent the possibility of panel disﬁguration or damage to

the internal components.

• Do not place the device in an unstable position where it might

accidentally fall over.

• Do not block the vents. This device has ventilation holes at the rear to

prevent the internal temperature from becoming too high. Inadequate

ventilation can result in overheating, possibly causing damage to the

device(s), or even ﬁre.

• Before connecting the device to other devices, turn off the power for all

devices. Before turning the power on or off for all devices, set all

volume levels to minimum.

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

Connections

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

ENGLISH

MSR250 Owner’s Manual

• When turning on the AC power in your audio system, always turn on the

device LAST, to avoid speaker damage. When turning the power off, the

device should be turned off FIRST for the same reason.

• Do not insert your ﬁngers or hands in any gaps or openings on the

device (vents, ports, etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.)

into any gaps or openings on the device (vents, ports, etc.) If this

happens, turn off the power immediately and unplug the power cord

from the AC outlet. Then have the device inspected by qualiﬁed Yamaha

service personnel.

• Do not use the device for a long period of time at a high or

uncomfortable volume level, since this can cause permanent hearing

loss. If you experience any hearing loss or ringing in the ears, consult a

physician.

• Do not operate the device if the sound is distorting. Prolonged use in

this condition could cause overheating and result in ﬁre.

• Do not rest your weight on the device or place heavy objects on it, and

avoid use excessive force on the buttons, switches or connectors.

Interference From Cell Phones

Using a cell phone near the speaker system can induce noise. If this occurs, move the cell phone further away from the speaker system.

Air blowing out of the bass reﬂex ports is normal, and often occurs when the speaker is handling program material with heavy bass content.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha service

personnel about replacing defective components.

Handling caution

XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost or destroyed.

* This applies only to products distributed

by YAMAHA CORPORATION OF AMERICA.

IMPORTANT

Please record the serial number of this unit in the space below.

Model

Serial No.

The serial number is located on the bottom or rear of the unit.

Retain this Owner’s Manual in a safe place for future reference.

(Ser.No)

• The illustrations as shown in this manual are for instructional purposes only, and may be different from the ones on your equipment.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Included Accessories

• Owner’s Manual

• Power Cord

ENGLISH

MSR250 Owner’s Manual

Thank you for purchasing the Yamaha MSR250 powered speaker.

The development of this powered speaker is a natural extension of Yamaha’s extensive experience and

knowledge of PA devices. The MSR250 faithfully reproduces sound for a wide range of applications. Please

read this manual thoroughly to make the best use of the MSR250 for the longest possible period of time. Keep

the manual in a safe place for future reference.

INPUT 1 jacks

These balanced XLR/phone jacks connect a micro-

phone, mixer, or electronic musical instrument, etc. Set

the MIC/LINE switch (

) depending on the level of

the input signal.

XLR-type connectors are wired as follows (IEC60268

standard): pin 1: ground, pin 2: hot (+), and pin 3: cold

(–).

NOTE:

You may use either the XLR or the phone jack, but not

both types simultaneously. Please connect to only one

type of jack on the channel.

MIC/LINE switch

Set this switch to MIC or LINE for INPUT 1 jacks,

depending on the level of the input signal. For low-level

signals (such as microphones), set the switch to the MIC

( ) position. For high-level signals (such as electronic

musical instruments and audio equipment), set the

switch to the LINE ( ) position.

INPUT 2/3 jacks

These unbalanced phone/RCA pin jacks connect an

electronic musical instrument or audio equipment, etc.

NOTE:

You may use either the phone or RCA pin jacks, but not

both types simultaneously. Please connect to only one

type of jack on each channel.

LINK OUT jack

This outputs the mixed signals input via the INPUT1

and 2/3 jacks.

EQ controls

HIGH:

The HIGH control adjusts the output level at 10kHz

over a ±6 dB range. Rotate clockwise to boost or coun-

terclockwise to cut.

LOW:

The LOW control adjusts the output level at 60Hz over a

±3 dB range. Rotate clockwise to boost or counterclock-

wise to cut.

LEVEL controls

Determine the level of signals input from the INPUT1

or 2/3 jacks.

LIMITER indicator

This lights up if the output level is too high. In this case,

lower the level using the LEVEL controls (

) or lower

the input level.

POWER Indicator

This lights up when the power switch (

) is turned on.

When the protection circuit is activated due to overcur-

rent or heat, the output will be muted, with the POWER

indicator remaining lit.

Turn the power on again if you hear no sound after

waiting a while.

POWER switch

This switch turns the power on/off.

AC IN connector

Connect the included power cord here.

Part Names and Functions

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

ENGLISH

MSR250 Owner’s Manual

■

Connecting to a mixer

■

Connecting a microphone and

other sources directly

■

Daisy chain

NOTE:

The volume of each speaker will be virtually the same when the LEVEL controls for the second and subsequent units are set to

their nominal positions.

Connection Examples

LINE OUT L R

Mixer

Keyboard

LINE OUT L R

Mixer

To the next speakerTo the next speaker

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

MSR250 Owner’s Manual

■

General Speciﬁcations

Type ............................................ 2-way Bass Reﬂex Powered

Speaker

Speaker Unit

LF: ........................................... 10” (25cm) Cone

HF: .......................................... 1” (2.54cm) Compression

Driver

Frequency Range ......................... 55 Hz–20 kHz (–10 dB)

Maximum Output Level ............... 116 dB (1m on Axis)

Directional Angle ......................... 90° (H)/40° (V)

Dimension (W

D)................ 342

544.5

298 mm

Weight......................................... 14.1 kg

Color ........................................... Black

Tripod Pole Diameter ................... 35–36 mm

Included Accessories .................... Power cord (AC inlet type,

2.5 m), Owner’s Manual

■

Amp. Unit

Maximum Output Power ............. 200 W at 1 kHz, THD=1%,

RL=4

Ω

Crossover Frequency.................... 4.0 kHz (LF: 12dB/oct,

HF: 12dB/oct.)

Input Sensitivity

INPUT 1 (XLR): ........................ –60 dBu*(MIC),

–30 dBu* (LINE)

(Phone): .................... –50 dBu*(MIC),

–20 dBu* (LINE)

INPUT 2/3 (Phone/RCA-pin): ... –20 dBu*

Input Impedance

INPUT 1: ................................. 6 k

Ω

(XLR), 2 k

Ω

(Phone)

INPUT 2/3: .............................. 10 k

Ω

Output Impedance ...................... LINK OUT: 600

Ω

Controls

LEVEL Control: ......................... INPUT1, 2/3

CH EQ LOW: .......................... ±3 dB at 60 Hz

HIGH: ......................... ±6 dB at 10 kHz

POWER Switch (ON/OFF)

Input/Output Connectors

INPUT 1: ................................. XLR-3-31 / PHONE

(balanced)

INPUT 2/3: .............................. PHONE / RCA-pin

(unbalanced)

Indicators

POWER Indicator: .................... Green LED

LIMITER Indicator: ................... Red LED

Power Consumption .................... 40 W

* 0 dBu=0.775 V

Frequency Response

Horizontal Directivity

Speciﬁcations

Dimensions

342

544.5

120

152

2-M8 x 25

298

Tr ipod pole diameter 35-36

* Use of the stand should refer to stand

manufacturer's instructions.

Unit: mm

Performance Graph

Directivity Diagram

6300

8000

10000

3150

4000

5000

6dB / div.

Unit: Hz

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

MSR250 Owner’s Manual

* Speciﬁcations and descriptions in this owner’s manual are for

information purposes only. Yamaha Corp. reserves the right to

change or modify products or speciﬁcations at any time

without prior notice. Since speciﬁcations, equipment or

options may not be the same in every locale, please check

with your Yamaha dealer.

* Die technischen Daten und Beschreibungen in dieser

Bedienungsanleitung dienen nur der Information. Yamaha

Corp. behält sich das Recht vor, Produkte oder deren

technische Daten jederzeit ohne vorherige Ankündigung zu

verändern oder zu modiﬁzieren. Da die technischen Daten,

das Gerät selbst oder Sonderzubehör nicht in jedem Land

gleich sind, setzen Sie sich im Zweifel bitte mit Ihrem

Yamaha-Händler in Verbindung.

* Les caractéristiques techniques et les descriptions du mode

d’emploi ne sont données que pour information. Yamaha

Corp. se réserve le droit de changer ou modiﬁer les produits

et leurs caractéristiques techniques à tout moment sans

aucun avis. Du fait que les caractéristiques techniques, les

équipements et les options peuvent différer d’un pays à

l’autre, adressez-vous au distributeur Yamaha le plus proche.

* Las especiﬁcaciones y descripciones de este manual del

propietario tienen sólo el propósito de servir como

información. Yamaha Corp. se reserva el derecho a efectuar

cambios o modiﬁcaciones en los productos o especiﬁcaciones

en cualquier momento sin previo aviso. Puesto que las

especiﬁcaciones, equipos u opciones pueden no ser las

mismas en todos los mercados, solicite información a su

distribuidor Yamaha.

Block Diagram

INPUT

(CH1)

INPUT

(CH2/3)

LOW

BA BA

LEVEL

LIMITER

POWER

PROTECTION

LINK OUT

[0dBu]

LEVEL

LIMITER

SUM SUM

INV

SP EQ SP EQ

[–60 +20dBu]

[–20 +20dBu]

[–50 +30dBu]

[–26dBu]

MIC

LINE

(PUSH : LINE)

30dB

[–26dBu]

[–26dBu][–26dBu][–26dBu]

[–8dBu]

[–8dBu] [–8dBu] [0dBu]

[–8dBu]

[+12dBu] [+25dBu]

HIGH

LOW

HIGH

OVER CURRENT

ON/OFF MUTE

Те хнические характеристики и их описания в данном

руководстве пользователя предназначены только для

общего сведения. Корпорация Yamaha сохраняет за

собой право модифицировать свои изделия и менять их

технические характеристики без предварительного

уведомления. Поскольку технические характеристики,

оборудование и набор возможностей могут зависеть от

региона, обращайтесь за информацией к местному

представителю корпорации Yamaha.

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

Memo

MSR250 Owner’s Manual

CANADA

Yamaha Canada Music Ltd.

135 Milner Avenue, Scarborough, Ontario,

M1S 3R1, Canada

Tel: 416-298-1311

U.S.A.

Yamaha Corporation of America

6600 Orangethorpe Ave., Buena Park, Calif. 90620,

U.S.A.

Tel: 714-522-9011

MEXICO

Yamaha de México S.A. de C.V.

Calz. Javier Rojo Gómez #1149,

Col. Guadalupe del Moral

C.P. 09300, México, D.F., México

Tel: 55-5804-0600

BRAZIL

Yamaha Musical do Brasil Ltda.

Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi,

CEP 04534-013 Sao Paulo, SP. BRAZIL

Tel: 011-3704-1377

ARGENTINA

Yamaha Music Latin America, S.A.

Sucursal de Argentina

Viamonte 1145 Piso2-B 1053,

Buenos Aires, Argentina

Tel: 1-4371-7021

PANAMA AND OTHER LATIN

AMERICAN COUNTRIES/

CARIBBEAN COUNTRIES

Yamaha Music Latin America, S.A.

Torre Banco General, Piso 7, Urbanización Marbella,

Calle 47 y Aquilino de la Guardia,

Ciudad de Panamá, Panamá

Tel: +507-269-5311

THE UNITED KINGDOM

Yamaha Music U.K. Ltd.

Sherbourne Drive, Tilbrook, Milton Keynes,

MK7 8BL, England

Tel: 01908-366700

GERMANY

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

SWITZERLAND/LIECHTENSTEIN

Yamaha Music Central Europe GmbH,

Branch Switzerland

Seefeldstrasse 94, 8008 Zürich, Switzerland

Tel: 01-383 3990

AUSTRIA

Yamaha Music Central Europe GmbH,

Branch Austria

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-60203900

CZECH REPUBLIC/SLOVAKIA/

HUNGARY/SLOVENIA

Yamaha Music Central Europe GmbH,

Branch Austria, CEE Department

Schleiergasse 20, A-1100 Wien, Austria

Tel: 01-602039025

POLAND

Yamaha Music Central Europe GmbH

Sp.z. o.o. Oddzial w Polsce

ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland

Tel: 022-868-07-57

THE NETHERLANDS/

BELGIUM/LUXEMBOURG

Yamaha Music Central Europe GmbH,

Branch Benelux

Clarissenhof 5-b, 4133 AB Vianen, The Netherlands

Tel: 0347-358 040

FRANCE

Yamaha Musique France

BP 70-77312 Marne-la-Vallée Cedex 2, France

Tel: 01-64-61-4000

ITALY

Yamaha Musica Italia S.P.A.

Combo Division

Viale Italia 88, 20020 Lainate (Milano), Italy

Tel: 02-935-771

SPAIN/PORTUGAL

Yamaha Música Ibérica, S.A.

Ctra. de la Coruna km. 17, 200, 28230

Las Rozas (Madrid), Spain

Tel: 91-639-8888

SWEDEN

Yamaha Scandinavia AB

J. A. Wettergrens Gata 1, Box 30053

S-400 43 Göteborg, Sweden

Tel: 031 89 34 00

DENMARK

YS Copenhagen Liaison Ofﬁce

Generatorvej 6A, DK-2730 Herlev, Denmark

Tel: 44 92 49 00

NORWAY

Norsk ﬁlial av Yamaha Scandinavia AB

Grini Næringspark 1, N-1345 Østerås, Norway

Tel: 67 16 77 70

RUSSIA

Yamaha Music (Russia)

Ofﬁce 4015, entrance 2, 21/5 Kuznetskii

Most street, Moscow, 107996, Russia

Tel: 495 626 0660

OTHER EUROPEAN COUNTRIES

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: +49-4101-3030

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2313

TURKEY/CYPRUS

Yamaha Music Central Europe GmbH

Siemensstraße 22-34, 25462 Rellingen, Germany

Tel: 04101-3030

OTHER COUNTRIES

Yamaha Music Gulf FZE

LOB 16-513, P.O.Box 17328, Jubel Ali,

Dubai, United Arab Emirates

Tel: +971-4-881-5868

THE PEOPLE’S REPUBLIC OF CHINA

Yamaha Music & Electronics (China) Co.,Ltd.

25/F., United Plaza, 1468 Nanjing Road (West),

Jingan, Shanghai, China

Tel: 021-6247-2211

INDONESIA

PT. Yamaha Music Indonesia (Distributor)

PT. Nusantik

Gedung Yamaha Music Center, Jalan Jend. Gatot

Subroto Kav. 4, Jakarta 12930, Indonesia

Tel: 21-520-2577

KOREA

Yamaha Music Korea Ltd.

8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong,

Kangnam-Gu, Seoul, Korea

Tel: 080-004-0022

MALAYSIA

Yamaha Music Malaysia, Sdn., Bhd.

Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,

Petaling Jaya, Selangor, Malaysia

Tel: 3-78030900

SINGAPORE

Yamaha Music Asia Pte., Ltd.

#03-11 A-Z Building

140 Paya Lebor Road, Singapore 409015

Tel: 747-4374

TAIWAN

Yamaha KHS Music Co., Ltd.

3F, #6, Sec.2, Nan Jing E. Rd. Taipei.

Taiwan 104, R.O.C.

Tel: 02-2511-8688

THAILAND

Siam Music Yamaha Co., Ltd.

891/1 Siam Motors Building, 15-16 ﬂoor

Rama 1 road, Wangmai, Pathumwan

Bangkok 10330, Thailand

Tel: 02-215-2626

OTHER ASIAN COUNTRIES

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2317

AUSTRALIA

Yamaha Music Australia Pty. Ltd.

Level 1, 99 Queensbridge Street, Southbank,

Victoria 3006, Australia

Tel: 3-9693-5111

COUNTRIES AND TRUST

TERRITORIES IN PACIFIC OCEAN

Yamaha Corporation,

Asia-Paciﬁc Music Marketing Group

Nakazawa-cho 10-1, Naka-ku, Hamamatsu,

Japan 430-8650

Tel: +81-53-460-2313

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division

Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650

Tel: +81-53-460-2441

PA19

For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below.

712IP-01A0

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

Yamaha Pro Audio global web site:

http://www.yamahaproaudio.com/

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

Printed in China

Yamaha MSR250 Руководство пользователя

Похожие модели бренда