Yamaha DSP-A5 Инструкция по применению

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia ID

V472000

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

DSP-A5

Natural Sound AV Amplifier

Amplificateur audio-vidéo

DSP-A5

G B

00DSP-A5-cv(ML) 3/1/0, 10:50 AM1

CAUTION

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1. To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2. Install this unit in a cool, dry, clean place — away

from windows, heat sources, sources of excessive

vibration, dust, moisture and cold. Avoid sources of

humming (transformers, motors). To prevent fire or

electrical shock, do not expose the unit to rain or

water.

3. Never open the cabinet. If something drops into the

unit, contact your dealer.

4. Do not use force on switches, controls or connection

cables. When moving the unit, first disconnect the

power cord and then the cables connected to other

component. Never pull the cables themselves.

5. The openings on the cover assure proper ventilation

of the unit. If these openings are obstructed, the

temperature inside the unit will rise rapidly.

Therefore, avoid placing objects against these

openings, and install the unit in a well-ventilated area

to prevent fire and damage.

Be sure to allow a space of at least 20 cm behind,

20 cm on both sides and 30 cm above the top panel

of the unit to prevent fire and damage.

6. The voltage used must be the same as that specified

on this unit. Using this unit with a higher voltage than

specified is dangerous and may result in fire or other

accidents. YAMAHA will not be held responsible for

any damage resulting from the use of this unit with a

voltage other than that specified.

7. Digital signals generated by this unit may interfere

with other component such as tuners, receivers and

TVs. Move this unit farther away from such

component if interference is observed.

8. Always set VOLUME to the “m” position before

starting the audio source play. Increase the volume

gradually to an appropriate level after playback has

been started.

9. Do not attempt to clean the unit with chemical

solvents; this might damage the finish. Use a clean,

dry cloth.

10. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before

concluding that the unit is faulty.

11. When not planning to use this unit for a long period

of time (e.g., a vacation), disconnect the AC power

cord from the wall outlet.

12. To prevent lightning damage, disconnect the AC

power cord and disconnect the antenna cable when

there is an electrical storm.

13. Grounding or polarization — Precautions should be

taken so that the grounding or polarization of the unit

is not defeated.

14. AC outlet — Do not connect audio component to the

AC outlet on the rear panel if that component

requires more power than the outlet is rated to

provide.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off. This state is called the standby

mode. In this state, this unit is designed to consume a

very small quantity of power.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note

• The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug, proceed

as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured BROWN

must be connected to the terminal which is marked with

the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

0101DSP-A5_caution_EN 2/29/0, 4:53 PM2

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

1

FEATURES

5-Channel Power Amplification

◆ Minimum RMS Output

(0.06% THD, 20 Hz – 20 kHz)

Main: 70 W +70 W (8 Ω)

Center: 70 W (8 Ω)

Rear: 70 W + 70 W (8 Ω)

Multi-Mode Digital Sound Field

Processing

◆ Digital Sound Field Processor (DSP)

◆ Dolby Pro Logic Decoder

◆ Dolby Digital Decoder

◆ DTS Decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

Technology and Dolby Pro Logic, Dolby Digital or

DTS

Other Features

◆ 96-kHz/24-bit D/A Converter

◆ “SET MENU” which Provides You with 12 Items

for Optimizing This Unit for Your Audio/Video

System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other Future

Formats

◆ S Video Signal Input/Output Capability

◆ 3 Optical/2 Coaxial Digital Signal Input Terminals

◆ SLEEP Timer

◆ Remote Control with Preset Manufacturer Codes

INTRODUCTION

CONTENTS

PREPARATION

SPEAKER SETUP....................................................... 9

CONNECTIONS........................................................ 10

ADJUSTING THE SPEAKER BALANCE ............ 17

BASIC OPERATION

PLAYING A SOURCE .............................................. 19

DIGITAL SOUND FIELD PROCESSOR (DSP)

EFFECT .................................................................. 23

RECORDING A SOURCE ON TAPE, MD OR

VIDEO CASSETTE ............................................... 25

ADVANCED OPERATION

SOUND FIELD PROGRAM .................................... 26

SET MENU................................................................. 29

DELAY TIME AND SPEAKER

OUTPUT LEVELS ................................................. 33

SLEEP TIMER .......................................................... 35

PRESET REMOTE CONTROL .............................. 36

APPENDIX

TROUBLESHOOTING ............................................ 44

SPECIFICATIONS.................................................... 48

GLOSSARY................................................................ 49

INDEX ........................................................................ 50

INTRODUCTION

FEATURES .................................................................. 1

CONTENTS ................................................................. 1

GETTING STARTED ................................................. 2

CONTROLS AND FUNCTIONS ............................... 4

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic” and the

double-D symbol are trademarks of Dolby

Laboratories. Confidential Unpublished Works.

rights reserved.

Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other world-wide patents issued and

pending. “DTS”, “DTS Digital Surround”, are trademarks of

y indicates a tip for your operation.

• When buttons on this unit and the remote control are

noted together in this Owner’s Manual, these button

names are in principle noted in the order of “button name

(remote control button name)”.

0102DSP-A501-08_EN 2/29/0, 4:53 PM1

2

GETTING STARTED

Checking the Package Contents

Check that the following items are included in your package.

Remote control

Batteries (AAA, R03, UM-4 type)

Quick reference card

Connection guide

Battery Installation in the Remote

Control

1 Turn the remote control over and slide the

battery compartment cover in the direction of

the arrow.

2 Insert the batteries (AAA, R03 or UM-4 type)

according the polarity markings on the inside

of the battery compartment.

3 Close the battery compartment cover.

Battery Replacement

If the remote control operates only when it is close to the

unit, the batteries are weak. Replace all the batteries with

new ones.

Be sure to replace the batteries within about two minutes.

If it takes longer than two minutes, the codes set for the

remote control will return to the factory settings. (Refer

to pages 36 to 43 about the remote control.)

Notes

• Use only AAA, R03 or UM-4 batteries for replacement.

• Be sure the battery polarity is correct. (See the illustration inside

the battery compartment.)

• Remove the batteries if the remote control will not be used for an

extended period of time.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

1

2

3

Quick Reference Card

0102DSP-A501-08_EN 2/29/0, 4:53 PM2

3

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

Using the Remote Control

The remote control transmits a directional infrared beam. Be

sure to aim the remote control directly at the infrared sensor

during operation. When the sensor is covered or there is a

large object between the remote control and the sensor, the

sensor cannot receive signals. The sensor may not be able to

receive signals properly when it is exposed to direct sunlight

or a strong artificial light (such as a fluorescent or strobe

light). In this case, change the direction of the light or

reposition the unit to avoid direct lighting.

Notes

• Handle the remote control with care.

• Do not spill water, tea or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following

conditions:

– high humidity or temperature such as near a heater, stove or

bath;

– dusty places; or

– extremely low temperature.

GETTING STARTED

Remote control

sensor

Within approximately 6 m

(20 feet)

0102DSP-A501-08_EN 2/29/0, 4:53 PM3

4

LR

–

+

–

+



12 3 4 65

7890qwert y

5

INPUT SELECTOR

Turn this selector to select the input source (TUNER, CD,

PHONO, CBL/SAT, V-AUX, VCR, D-TV, DVD/LD) that

you want to listen to or watch. The arrow for the selected

input source indicator lights up on the display.

6 VOLUME

Turn this control to turn up or down the volume.

7 PHONES jack

Connect the headphones to the PHONES jack. You can

listen to the sound to be output from the main speakers

through the headphones.

When listening with headphones privately, set both

SPEAKERS A and B to the OFF position, press EFFECT to

turn off the effect speakers (center and rear) and set “BASS

OUT” on the SET MENU to the MAIN position (so that no

DSP program name appears on the display).

CONTROLS AND FUNCTIONS

Front Panel

1 STANDBY/ON

Press this switch to turn on the power of this unit or to set

this unit in the standby mode. Before turning the power on,

set VOLUME to the “m” position.

Standby mode

In this mode, this unit consumes a very small quantity of

power to receive infrared-signals from the remote

control.

2 Remote control sensor

This receives signals from the remote control.

3 Display

This shows various information. (Refer to page 6 for

details.)

4 INPUT MODE

Press this button to select the input mode among AUTO,

DTS and ANALOG for the DVD/LD, TV/digital TV and

cable TV/satellite tuner sources.

0102DSP-A501-08_EN 2/29/0, 4:53 PM4

5

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

8 SPEAKERS

Set A or B (or both A and B) to the ON position for the main

speaker system (connected to this unit) that you want to use.

Set the button(s) to the OFF position for the main speaker

system that you don’t want to use.

9 SET MENU +/–

Press these buttons to adjust the setting on the SET MENU.

0 NEXT

This button is used to shift the selection to the next item on

the SET MENU.

q Tone controls

These controls are only effective for the sound from the

main speakers.

a) BASS

Turn this control clockwise to increase or counterclockwise

to decrease the low-frequency response. The “0” position

produces a flat response.

b) TREBLE

Turn this control clockwise to increase or counterclockwise

to decrease the high-frequency response. The “0” position

produces a flat response.

w TAPE/MD MON / EXT. DECODER

Press this button to select a tape or an MD source. The

“TAPE/MD MONITOR” indicator lights up on the display.

When you press the button again, the “TAPE/MD

MONITOR” indicator goes off, “EXT. DECODER” appears

on the display and you can listen to a source connected to

the EXTERNAL DECODER INPUT terminals.

e BALANCE

This control is only effective for the sound from the main

speakers.

Turn the control to adjust the balance of the output volume

from the right and left main speakers to compensate for

sound imbalance caused by the speaker location or listening

room conditions.

r EFFECT

Press this button to turn on or off the effect speakers (center

and rear). If you turn them off, the signals of the center and

rear channels are directed to the right and left main speakers

when playing a source encoded with Dolby Digital and

DTS. In this case, the output levels of the right and left

speakers may not match.

t PROGRAM selector

Press l or h to select a DSP program when the effect

speakers (center and rear) are turned on. The name of the

selected program appears on the display.

y VIDEO AUX terminals

Connect an auxiliary audio or video input source such as a

camcorder to these terminals. If the connected video unit

has an S video output terminal, connect it to the S VIDEO

terminal to obtain a high-resolution picture. Use INPUT

SELECTOR to select the source connected to these

terminals.

CONTROLS AND FUNCTIONS

0102DSP-A501-08_EN 2/29/0, 4:53 PM5

6

Display

4 Input source indicators

One of the arrows for these indicators lights up depending

on which source is selected.

5 TAPE/MD MONITOR indicator

This lights up when the tape deck or MD recorder, etc. is

selected as the input source by pressing TAPE/MD MON /

EXT. DECODER (or TAPE/MD).

6 g and o indicators

“ g ” lights up when the built-in Dolby Digital

decoder is on. “ o ” lights up when the built-in

Dolby Pro Logic decoder is on.

7 x indicator

“ x ” lights up when the built-in digital sound

field processor is on.

8 SLEEP indicator

This lights up while the built-in SLEEP timer is on.



CONTROLS AND FUNCTIONS

1 t indicator

The “t” indicator lights up when the built-in DTS

decoder is on.

2 DSP program indicators

These indicators light up when DSP program No. 2, 3 or the

subprogram “ENHANCED” of No. 1 is selected.

3 Multi-information display

This display shows various information: for example the

name of the selected DSP program and the various settings

during adjustment with the SET MENU.

0102DSP-A501-08_EN 2/29/0, 4:53 PM6

7

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

Remote Control

CONTROLS AND FUNCTIONS

1

2

8

9

0

3

q

4

w

6

r

e

t

y



u

7

5

TV VOLUME

TV POWER

TV INPUT

EFFECT

Select the

AMP/TUN

position.

This section describes the basic operation of this unit with

the remote control. First, set the selector dial to the AMP/

TUN position. Refer to “PRESET REMOTE CONTROL”

on page 36 for full details.

1 DSP

Press this button to switch the function of the numeric

buttons to the DSP program selector. (Refer to page 8.)

2 Indicator window

This displays the name of components which can be

controlled.

3 Numeric buttons (Input selector buttons)

These buttons select the input source.

CD: To play a CD

TUNER: To listen to an FM (RDS) or AM broadcast

TAPE/MD: To play a tape or MD

DVD/LD: To play a DVD or LD

D-TV: To watch a TV

VCR: To play a video cassette

PHONO: To play an analog record

CBL/SAT: To watch cable TV or satellite broadcast

V-AUX: To use a camcorder

EXT. DEC.: To play another multi-channel source

Refer to page 8 for details.

4 TEST

Press this button to output the test tone for each speaker.

5 j (left), i (right)

These buttons adjust the settings of the SET MENU and

TIME/LEVEL mode.

6 TIME/LEVEL

Press this button to select the items in the TIME/LEVEL

mode.

7 SLEEP

Press this button to set the SLEEP timer.

8 INPUT

Press this button to switch the function of the numeric

buttons to the input selector. (Refer to page 8.)

9 Indicator

This flashes in red when pressing a button on the remote

control.

0 Selector dial

Turn this dial to select the position for the component to be

controlled. (The proper code must be set for your

component. Refer to “Setup codes” on page 42.) When the

position is selected, the remote control is set to that

component operation mode.

Refer to

page 8.

0102DSP-A501-08_EN 2/29/0, 4:53 PM7

8

q A/B/C/D/E, PRESET +/–

These buttons are used to select a preset station when using

the YAMAHA tuner.

A/B/C/D/E: To select one of a group (A to E) of preset

stations

PRESET +/–: To select a preset station number (1 to 8)

w d (next), u (back)

These buttons are used to advance or go back one selection

on the SET MENU and TIME/LEVEL mode.

e SET MENU

Press this button to select the items on the SET MENU.

r POWER

Press this button to turn this unit on.

t STANDBY

Press this button to set this unit in the standby mode.

y VOLUME (+/–)

These buttons are used to adjust the volume level.

u MUTE

Press this button to mute the sound. To cancel mute, press

this button again.

EFFECT

Press this button to turn on or off the effect speakers (center

and rear) in the following cases:

• When the selector dial is set to the DSP/TUN position.

• While the indicator is lit for about three seconds after

pressing DSP.

Description of the Numeric Buttons

The Numeric buttons function in various ways depending

on the position of the selector dial or the combination of

other instructions.

■ When selecting an input source

1 Press INPUT regardless of the position of the

selector dial.

The indicator lights up for about three seconds.

2 You can select an input source with the

numeric buttons while the indicator is lit.

CONTROLS AND FUNCTIONS

■ When selecting a DSP program

and turning on or off the effect

speakers (center and rear)

A

1 Press DSP regardless of the position of the

selector dial.

The indicator lights up for about three seconds.

2 You can select a DSP program with the

numeric buttons (1 to 8) and turn on or off the

effect speakers (center and rear) by pressing

EFFECT while the indicator is lit.

B

1 Set the selector dial to the DSP/TUN position.

2 You can select a DSP program directly with the

numeric buttons (1 to 8) and turn on or off the

effect speakers (center and rear) by pressing

EFFECT.

A

B

0102DSP-A501-08_EN 2/29/0, 4:53 PM8

9

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

SPEAKER SETUP

Speaker Placement

Refer to the following diagram when you place the

speakers.

Speakers to Be Used

This unit is designed to provide the best sound-field quality

with a 5-speaker system, using main speakers, rear speakers

and a center speaker. If you use different brands of speakers

(with different tonal qualities) in your system, the tone of a

moving human voice and other types of sound may not shift

smoothly. We recommend that you use speakers from the

same manufacture or speakers with the same tonal quality.

The main speakers are used for the main source sound plus

the effect sounds. They will probably be the speakers from

your present stereo system. The rear speakers are used for

the effect and surround sounds, and the center speaker is for

the center sounds (dialog, vocals, etc.). If for some reason it

is not practical to use a center speaker, you can do without

it. Best results, however, are obtained with the full system.

The main speakers should be high-performance models and

have enough power-handling capacity to accept the

maximum output of your audio system. The other speakers

do not have to be equal to the main speakers. For precise

sound localization, however, it is ideal to use high-

performance models that can reproduce sounds over the full

range for the center speaker and the rear speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is effective

not only for reinforcing bass frequencies from any or all

channels, but also for reproducing the LFE (low frequency

effect) channel with high fidelity when playing back a

source encoded with Dolby Digital or DTS. The YAMAHA

Active Servo Processing Subwoofer System is ideal for

natural and lively bass reproduction.

Main

speaker (L)

Center speaker

Main speaker (R)

Subwoofer

Rear speaker (L)

Rear speaker (R)

1.8 m

■ Main speakers

Place the right and left main speakers an equal distance

from the ideal listening position. The distance of each

speaker from each side of the TV monitor should be the

same.

■ Rear speakers

Place these speakers behind your listening position, facing

slightly inwards, nearly 1.8 m (approx. 6 feet) above the

floor.

■ Center speaker

Align the front face of the center speaker with the front face

of your TV monitor. Place the speaker as close to the

monitor as possible, such as directly over or under the

monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the center channel sound will be

heard from the right and left main speakers. In that case,

“CENTER SP” on the SET MENU is set to the NONE position.

(Refer to page 30 for details.)

■ Subwoofer

The position of the subwoofer is not so critical, because low

bass sounds are not highly directional. But it is better to

place the subwoofer near the main speakers. Turn it slightly

toward the center of the room to reduce the wall reflections.

CAUTION

Some types of speakers interfere with a TV monitor. If

this problem occurs, move the speakers away from the

monitor. If you cannot avoid installing the center speaker

or subwoofer near the TV monitor, use magnetically

shielded speakers.

PREPARATION

0103DSP-A509-18_EN 2/29/0, 4:53 PM9

10

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been

completed.

Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some

components require different connection methods and have different terminal names. Refer to the instructions for each

component to be connected to this unit.

When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect

it to the terminals with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products.

Use RCA-type pin plug cables for connecting audio/video components with the exception described later.

The input and output terminals for pin plugs can be distinguished as follows:

Yellow video signals (composite)

White analog audio signals for the left channel

Red analog audio signals for the right channel

coaxial digital signals

After completing all connections, check them again to make sure they are correct.

A

B

Connecting an Audio

Component (page 11)

Connecting a Video

Component (pages 12 and 13)

IMPEDANCE SELECTOR

switch (page 16)

Connecting to an External

Decoder (page 13)

Connecting the Speakers

(pages 14 and 15)

Connecting the Power

Supply Cords (page 16)

(Europe model)

V V

C C

L

R

L

R

0103DSP-A509-18_EN 2/29/0, 4:53 PM10

11

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

Connecting an Audio Component

■ PHONO terminals

These terminals are used to connect a turntable with an MM

or high-output MC cartridge. If you have a turntable with a

low-output MC cartridge, use an inline boosting transformer

or MC head amplifier when connecting to these terminals.

y

Connecting the ground (earth) wire of the turntable to the GND

terminal will normally minimize hum, but in some cases, better

results may be obtained with the ground wire disconnected.

CONNECTIONS

Be sure to connect the right channel (R), left channel (L),

input (IN) and output (OUT) properly.

Tape deck or

MD recorder

L R

L

R

OUTPUT

L R L R

OUTPUT OUTPUT

LINE OUT

LINE IN

GND

Turntable

(Europe model)

CD player

Analog signal

Signal flow

Tuner

0103DSP-A509-18_EN 2/29/0, 4:53 PM11

12

Connecting a Video Component

■ Audio signal terminals

Be sure to connect the right channel (R), left channel (L),

input (IN) and output (OUT) properly.

■ S Video signal terminals

Use a special S VIDEO cable (commercially available) for

the S VIDEO connection.

■ Digital audio signal terminals

If your DVD/LD player, TV/digital TV or cable TV/satellite

tuner, etc. has coaxial or optical digital signal output

terminals, they can be connected to this unit’s COAXIAL

and/or OPTICAL digital signal input terminals. To make a

connection between the optical digital signal terminals,

remove the cover from each terminal, and then connect

them by using a commercially available optical fiber cable

that conforms to EIA standards. Other cables might not

function correctly.

When making connections between the digital signal

terminals, you should connect the components to the same-

named analog audio signal terminals of this unit, because a

digital signal cannot be recorded by a tape deck, MD

recorder or VCR connected to this unit.

Notes

• Be sure to attach the covers when the OPTICAL terminals are not

being used in order to protect them from dust.

• If your LD player has a Dolby Digital RF signal output terminal,

be sure to use the RF demodulator (separately purchased).

• No sound will be heard when connecting your LD player’s Dolby

Digital RF signal output terminal directly to this unit’s COAXIAL

DVD/LD digital signal input terminal.

y

• The input signal from the DVD/LD or CBL/SAT input terminals

is selected in the following order of priority with the input mode

set to AUTO: COAXIAL terminal → OPTICAL terminal →

Analog terminal. Refer to page 21 for details.

• All digital signal input terminals are applicable to sampling

frequencies of 32 kHz, 44.1 kHz, 48 kHz and 96 kHz. (Refer to

page 22 about 96-kHz sampling 24-bit digital signals.)

CONNECTIONS

L R

L

R

C

L R

ANALOG

AUDIO OUT

AUDIO

IN

ANALOG

AUDIO OUT

AUDIO

OUT

S VIDEO

OUT

S VIDEO

OUT

OPTICAL

DIGITAL OUT

S VIDEO

IN

S VIDEO

OUT

S VIDEO

IN

COAXIAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

O

S S

S

SS

S

L R

ANALOG

AUDIO OUT

S VIDEO

OUT

OPTICAL

DIGITAL OUT

O

S

C

COAXIAL

DIGITAL OUT

DVD/LD player Cable TV/satellite tuner

(Europe model)

Analog signal

S Video signal

Digital signal

(optical)

Digital signal

(coaxial)

Signal flow

TV monitor

TV/digital TV

VCR

0103DSP-A509-18_EN 2/29/0, 4:53 PM12

13

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

■ VIDEO terminals (composite)

If your video components do not have “S” video terminals,

they can be connected to this unit’s VIDEO terminals. Be

sure to connect the input (IN) and output (OUT) properly.

Note

• If video signals are input from both the S VIDEO input and

composite input terminals, the signals will be directed to their

respective output terminals.

■ TV monitor with a 21-pin connector

Make a connection as shown above with a commercially available SCART-plug connector cable.

■ VIDEO AUX terminals (on the front panel)

These terminals are used to connect any video input source

such as a camcorder to this unit.

Connecting to an External Decoder

This unit has additional 6-channel audio signal input

terminals for connecting an external decoder to this unit.

Connect the 6-channel audio signal output terminals of the

decoder to the EXTERNAL DECODER INPUT terminals

of this unit.

Notes

• When a source connected to these terminals is selected, the digital

sound field processor cannot be used.

• The settings of “CENTER SP”, “REAR SP”, “MAIN SP” and

“BASS OUT” on the SET MENU have no effect on a source

connected to these terminals. The setting of “MAIN LVL” is

effective. (Refer to pages 30 and 31 for details.)

• Adjustment of the output level of the center speaker, rear speakers

and subwoofer is effective when a source connected to these

terminals is selected as the input source. (Refer to page 33 for

details.)

CONNECTIONS

L R

V

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

S VIDEO OUT

S

DVD/LD player

L R L R

MAIN

OUT

SURROUND

OUT

CENTER

OUT

SUBWOOFER

OUT

External decoder

(Europe model)

V

VIDEO

IN

V

L R

V

VIDEO OUT

V

VIDEO OUT

V

VIDEO

OUT

V

VIDEO

OUT

V

VIDEO

IN

Cable TV/satellite tuner

TV/digital TV

VCR

SCART-plug

No

connection

Video signal

Signal flow

Camcorder

TV monitor

0103DSP-A509-18_EN 2/29/0, 4:53 PM13

14

Connecting the Speakers

Be sure to connect the right channel (R), left channel (L),

“+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the

polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTIONS

• Use speakers with the specified impedance shown on

the rear panel of this unit.

• Do not let the bare speaker wires touch each other and

do not let them touch any metal part of this unit. This

could damage the unit and/or speakers.

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these

terminals. If you use only one speaker system, connect it to

either of the SPEAKERS A or B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

CONNECTIONS

R

L

Main speakers A

Right Left

Main speakers B

Right Left

(Europe model)

Center speaker Rear speakers

Right Left

Subwoofer connection

When using a subwoofer with built-

in amplifier, including the

YAMAHA Active Servo Processing

Subwoofer System, connect the

input terminal of the subwoofer

system to the SUBWOOFER

OUTPUT terminal of this unit.

Low bass signals distributed from

the main, center and/or rear

channels are directed to this

terminal. (The cut-off frequency of

this terminals is 90 Hz.) The LFE

(low frequency effect) signals

generated when Dolby Digital or

DTS is decoded are also directed if

they are assigned to this terminal.

Subwoofer

system

0103DSP-A509-18_EN 2/29/0, 4:53 PM14

15

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

■ Speaker cables

1 Remove approx. 10 mm (3/8”) of insulation

from each of the speaker cables.

2 Twist the exposed wires of the cable together

to prevent short circuits.

■ Connecting to the MAIN SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side of

each terminal.

3 Tighten the knob to secure the wire.

■ Connecting to the REAR and CENTER SPEAKERS terminals

1 Open the tab.

2 Insert one bare wire into the hole of each

terminal.

3 Return the tab to secure the wire.

■ Connecting to an external amplifier

The speaker connections described on page 14 are fine for most applications. If you wish to drive your existing amplifier, the

following terminals are available for connecting an external amplifier(s) to this unit.

Note

• Output signals from these terminals are affected by the use of VOLUME, BASS, TREBLE and BALANCE.

CONNECTIONS

2

1

3

Red: positive (+)

Black: negative (–)

2

3

1

Red: positive (+)

Black: negative (–)

1 MAIN OUTPUT terminals

These terminals are for the main channel line output.

Connect the input terminals of the external amplifier to

these terminals.

2 CENTER OUTPUT terminals

These terminals are for the center channel line output.

Connect the input terminals of the external amplifier to

these terminals.

3 REAR (SURROUND) OUTPUT terminals

These terminals are for the rear channel line output.

Connect the input terminals of the external amplifier to

these terminals.

Note

• If an external amplifier is connected to the MAIN, CENTER or

REAR OUTPUT terminals, disconnect the corresponding

speakers (main, center or rear) from the SPEAKERS terminals.

1

23

12

10 mm (3/8”)

(Europe model)

0103DSP-A509-18_EN 2/29/0, 4:53 PM15

16

IMPEDANCE SELECTOR Switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise the unit may be

damaged.

If this unit fails to turn on when STANDBY/ON (or POWER) is pressed, the IMPEDANCE SELECTOR switch may not

be fully slide to either position. If so, slide the switch to either position fully when this unit is in the standby mode.

Select the right or left position according to the impedance of speakers in your system. Be sure to move this switch only

when this unit is in the standby mode.

Connecting the Power Supply Cords

After completing all connections, connect the AC power

cord to an AC power outlet. Disconnect the AC power cord

if you will not use this unit for a long period of time.

■ AC OUTLETS (SWITCHED)

Europe model .................................................... 2 OUTLETS

U.K. model.......................................................... 1 OUTLET

Use these outlets to connect the power cords from your

components to this unit. The power to the AC OUTLET(S)

is controlled by this unit’s STANDBY/ON (or POWER and

STANDBY). These outlets will supply power to any

connected component whenever this unit is turned on. The

maximum power (total power consumption of components)

that can be connected to the AC OUTLET(S) is 100 W.

If you use left position right position

CONNECTIONS

(Europe model)

SWITCHED

(Europe model)

To AC outlet

IMPEDANCE

SELECTOR

Rear speakers The impedance of each

speaker must be 6 Ω or

higher.

The impedance of each

speaker must be 8 Ω or

higher.

Center

speaker

The impedance must be 6 Ω

or higher.

The impedance must be 8 Ω

or higher.

If you use one pair of main

speakers, the impedance of

each speaker must be 4 Ω or

higher.

If you use one pair of main

speakers, the impedance of

each speaker must be 8 Ω or

higher.

If you use two pairs of main

speakers, the impedance of

each speaker must be 8 Ω or

higher.

If you use two pairs of main

speakers, the impedance of

each speaker must be 16 Ω or

higher.

Main

speakers

0103DSP-A509-18_EN 2/29/0, 4:53 PM16

17

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

Using the Test Tone

The adjustment of each speaker sound output level should

be performed at your listening position with the remote

control. After completing the adjustments, use VOLUME

(+/–) at your listening position to check if the adjustments

are satisfactory.

1 Set the selector dial to the

AMP/TUN (or DSP/TUN)

position.

2 Press TEST.

“TEST LEFT” appears on the display.

3 Turn up the volume.

You will hear a test tone (like pink noise) from each

speaker for about two seconds in the following order:

left main speaker, center speaker, right main speaker,

right rear speaker and left rear speaker. The display

changes as shown below.

Notes

• If the test tone cannot be heard, turn down the volume, set the unit

in the standby mode and check the speaker connections.

• If the test tone cannot be heard from the center speaker, check the

setting of “CENTER SP” on the SET MENU.

ADJUSTING THE SPEAKER BALANCE

1

2,7

5

3

6

TEST

LEFT

TEST

RIGHT

TEST L SUR. TEST R SUR.

TEST CENTER

This procedure lets you adjust the sound output level

balance between the main, center and rear speakers by using

the built-in test tone generator. When this adjustment is

performed, the sound output level heard at the listening

position will be the same from each speaker. This is

important for the best performance of the digital sound field

processor, the Dolby Pro Logic decoder, Dolby Digital

decoder and DTS decoder.

Before You Start Adjusting

1 Set VOLUME to the “m”

position.

2 Turn the power on.

3 Press SPEAKERS A or B

to select the main

speakers to be used.

If you use two main speaker

systems, press both A and B.

4 Set BASS, TREBLE and BALANCE to the “0”

position.

LR

–+–+

12

4

3

LR

–+–+

0103DSP-A509-18_EN 2/29/0, 4:53 PM17

18

4 Adjust BALANCE on the

front panel so that the

sound output level of the

right main speaker and the

left main speaker is the

same.

5 Press TIME/LEVEL

repeatedly to select the

speaker to be adjusted.

“CENTER”, “R SUR.” or

“L SUR.” appears on the

display.

y

After pressing TIME/LEVEL once, you can also select the item by

pressing d. (Pressing u changes the selection in the reverse order.)

6 Press i to raise and j to

lower the level. Adjust the

sound output levels of the

center speaker and the

rear speakers so that they

become almost the same

as that of the main

speakers.

While adjusting, the test tone is

heard from the selected speaker.

Note

• You cannot adjust the delay time while the test tone is being heard

even if “DELAY” appears on the display.

ADJUSTING THE SPEAKER BALANCE

Front panel

LR

7 When the adjustment is complete, press TEST.

“TEST OFF” appears on the display and the test tone

stops.

Note

• If “CENTER SP” on the SET MENU is set to the NONE position,

the sound output level of the center speaker cannot be adjusted in

step 6. The center channel sound is automatically output from the

right and left main speakers.

y

• Once you have completed the adjustments, you can only adjust

the overall volume level of your audio system by using VOLUME

(or VOLUME (+/–)).

• If you use external amplifiers, you may also use their volume

controls to achieve the proper balance.

• If there is insufficient sound output from the center and rear

speakers, you may decrease the main speaker output level by

setting “MAIN LVL” on the SET MENU to “–10 dB”. (Refer to

page 31 for details.)

0103DSP-A509-18_EN 2/29/0, 4:53 PM18

Страница загружается ...

Yamaha DSP-A5 Инструкция по применению

Yamaha DSP-A5 Инструкция по применению

на других языках

Похожие модели бренда