Yamaha RX-V293 Инструкция по применению
- Категория
- Кассетные плееры
- Тип
- Инструкция по применению
OWNER’S MANUAL
MODE D’EMPLOI
Natural Sound AV Receiver
Récepteur audiovisuel
RX-V293
U C A
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A A unit and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the unit and
cart combination to overturn.
7 Wall or Ceiling Mounting – The unit
should be mounted to a wall or ceiling
only as recommended by the
manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat.
10 Power Sources – The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
SAFETY INSTRUCTIONS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
•
Explanation of Graphical Symbols
CAUTION
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
IMPORTANT
Please record the serial number of this unit in
the space below.
Model:
Serial No.:
The serial number is located on the rear of
the unit.
Retain this Owner’s Manual in a safe place
for future reference.
1
English
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
SPECIAL NOTES FOR FCC COMPOSITE
DEVICE (for US customers only)
This device is a composite system. The digital device
component may not cause harmful interference.
19 For US customers only:
Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
FCC INFORMATION (for US customers only)
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring
or distortion – and, most importantly, without affecting your
sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
We Want You Listening For A Lifetime
2
●
Indoor FM Antenna
●
AM Loop Antenna
●
Antenna adapter
(U.S.A. and Canada models only)
●
Remote Control Transmitter
●
Batteries (size AA, R6, UM-3)
After unpacking, check that the following parts are included.
TEST
—
+
DELAY TIME
PHONO
SKIP CD
DISC SKIP
—
+
A
/
B
/
C
/
D
/
E
TUNER
DIR A
A
/
B
TAPE
VCR
REC/PAUSE
—
+
PRESET
DIR B
VIDEO
EFFECT
VOLUME
PRO LOGIC
ROCK
SUR.
HALL
3 STEREO
DSP
SLEEPPOWER
SAFETY INSTRUCTIONS....Inside the Front Cover
SUPPLIED ACCESSORIES ...........................2
FEATURES .....................................................3
CAUTION ........................................................4
NOTES ABOUT THE REMOTE CONTROL
TRANSMITTER ...............................................5
PROFILE OF THIS UNIT ................................6
SPEAKER SETUP ..........................................7
CONNECTIONS ..............................................8
CONTROLS AND THEIR FUNCTIONS ........12
SPEAKER BALANCE ADJUSTMENT ..........16
BASIC OPERATIONS ...................................18
TUNING OPERATIONS ................................20
PRESET TUNING .........................................21
USING DIGITAL SOUND FIELD
PROCESSOR (DSP) ....................................24
TROUBLESHOOTING ..................................27
SPECIFICATIONS .........................................28
CONTENTS
SUPPLIED ACCESSORIES
3
English
FEATURES
●
5 Speaker Configuration
(Power Amp. Section)
Main: 50W + 50W (8Ω) RMS Output
Power, 0.04% THD, 20–20,000 Hz
Center: 50W (8Ω) RMS Output
Power, 0.04% THD, 1 kHz
Rear: 20W (8Ω) RMS Output
Power, 0.04% THD, 1 kHz
●
Digital Sound Field Processor
●
Dolby Pro Logic Surround Decoder
●
Automatic Input Balance Control for
Dolby Pro Logic Surround
●
Test Tone Generator for Easier Speaker
Balance Adjustment
●
3 Center Channel Modes
(NORM/WIDE/PHANTOM)
● 40-Station Random Access Preset Tuning
● Automatic Preset Tuning
● Preset Station Shifting Capability (Preset
Editing)
● IF Count Direct PLL Synthesizer Tuning
System
● Video Signal Input/Output Capability
● SLEEP Timer
● Remote Control Capability
4
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the unit to rain or water.
3. Never open the cabinet. If something drops into the set,
contact your dealer.
4. Do not use force on switches, controls or connection wires.
When moving the unit, first disconnect the power plug and
the wires connected to other equipment. Never pull the
wires themselves.
5. The openings on the cabinet assure proper ventilation of
the unit. If these openings are obstructed, the temperature
inside the cabinet will rise rapidly. Therefore, avoid placing
objects against these openings, and install the unit in well-
ventilated condition. Be sure to allow a space of at least
20 cm behind, 20 cm on the both sides and 30 cm above
the top panel of the unit. Otherwise it may not only damage
the unit, but also cause fire.
6. Always set the VOLUME control to “–
∞
” before starting
the audio source play. Increase the volume gradually to an
appropriate level after playback has been started.
7. Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding that
the unit is faulty.
9. When not planning to use this unit for long periods of time
(ie., vacation, etc.), disconnect the AC power plug from the
wall outlet.
10.To prevent lightning damage, disconnect the AC power
plug and antenna cable when there is an electrical storm.
11.Grounding or polarization – Precautions should be taken
so that the grounding or polarization of an appliance is not
defeated.
12.Do not connect audio equipment to the AC outlet on the
rear panel if the equipment requires more power than the
outlet is rated to provide.
13.Voltage Selector (China and General Models only)
The voltage selector on the rear panel of this unit must
be set for your local main voltage BEFORE plugging
into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off. This state is called the standby mode.
In this state, this unit is designed to consume a very small
quantity of power.
FOR CANADIAN CUSTOMERS
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT AND FULLY INSERT.
THIS CLASS B DIGITAL APPARATUS MEETS ALL
REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
FREQUENCY STEP switch (China and General Models
only)
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP switch (located
at the rear) according to the frequency spacing in your area.
Before setting this switch, disconnect the AC power plug of
this unit from the AC outlet.
CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE
STANDBY/ON SWITCH IS PRESSED;
The IMPEDANCE SELECTOR switch may not be set to
either end. If so, set the switch to either end when this unit
is in the standby mode.
IMPEDANCE SELECTOR
(U.S.A. model)
I20V 60Hz
I00W MAX. TOTAL
SWITCHED
AC OUTLETS
REAR
CENTER
MAIN
SINGLE
:
8
Ω
MIN. /SPEAKER
DUAL
:4
Ω
MIN. /SPEAKER
8
Ω
MIN. /SPEAKER
8
Ω
MIN. /SPEAKER
REAR
CENTER
MAIN
SINGLE
:
6
Ω
MIN. /SPEAKER
DUAL
:3
Ω
MIN. /SPEAKER
6
Ω
MIN. /SPEAKER
4
Ω
MIN. /SPEAKER
SET BEFORE POWER ON
IMPEDANCE SELECTOR
5
English
Battery installation
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
●
Use only AA, R6, UM-3 batteries for replacement.
●
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
●
Remove the batteries if the remote control transmitter is not
used for an extended period of time.
●
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
Remote control transmitter operation range
Notes
●
There should be no large obstacles between the remote
control transmitter and the main unit.
●
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid direct
lighting.
2
1
3
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
l6
20
28
40
60
l2
8
4
2
0
–dB
30°
30°
Remote control
sensor
Within approximately
6 m (19.7 feet)
6
PROFILE OF THIS UNIT
You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field
Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to
bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system,
and this unit will sonically transform your room into a totally new listening environment. In addition, you will get incredible realism
from sources encoded with Dolby Surround using the built-in Dolby Pro Logic Surround Decoder.
Please read this operation manual carefully and store it in a safe place for later reference.
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology enables you to get extremely
close to the sound of a live performance, but chances are you’ll
still notice something missing: the acoustic environment of the
live concert hall. Extensive research into the exact nature of
the sonic reflections that create the ambience of a large hall
has made it possible for Yamaha engineers to bring you this
same sound in your own listening room, so you’ll feel all the
sound of a live concert.
Furthermore, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of actual music venues to allow you to accurately
recreate live performance environments in your own home.
Dolby Pro Logic Surround
This unit employs a Dolby Pro Logic Surround decoder similar
to professional Dolby Stereo decoders used in many movie
theaters. By using the Dolby Pro Logic Surround decoder, you
can experience the dramatic realism and impact of Dolby
Stereo theater sound in your own home.
Dolby Pro Logic employs a four-channel-five-speaker system.
The Pro Logic Surround system divides the input signal into
four levels: the left and right main channels, the center channel
(used for dialog), and the rear surround sound channel (used
for sound effects, background noise, and other ambient
noises). The center channel allows listeners seated in even
less-than-ideal positions to hear the dialog originating from the
action on the screen while experiencing good stereo imaging.
Dolby Surround is encoded on many sound tracks of pre-
recorded video tapes, laserdiscs, and some TV/cable
broadcasts. When you play a source encoded with Dolby
Surround on this unit, the Dolby Pro Logic Surround decoder
decodes the signal and supplies the surround-sound effects to
you.
In addition, this unit features a built-in automatic input balance
control. This always assures you of the best performance
without manual adjustment.
Manufactured under license from Dolby Laboratories Licensing
Corporation. “Dolby”, the double-D symbol and “Pro Logic” are
trademarks of Dolby Laboratories Licensing Corporation.
7
English
SPEAKER SETUP
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with a 5-speaker configuration. The most effective speakers to use with
this unit are main speakers, rear speakers and a center speaker. You can use only one rear speaker instead of using two rear
speakers, and omit the center speaker. (Refer to the “SPEAKER CONFIGURATION” shown below.)
The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your
present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center
sounds (dialog etc.) within the programs encoded with Dolby Surround. The center speaker needs to be equal in power to the main
speakers although the rear speakers should not be equal. However, all the speakers should have high enough power handling to
accept the maximum output of this unit.
SPEAKER CONFIGURATION
5-Speaker Configuration
This configuration is the most effective and recommended one.
In this configuration, the center speaker is necessary as well as
the rear speakers. If the program PRO LOGIC or 3
STEREO is selected, conversations will be output from the
center speaker and the ambience will be excellent.
• Set the center channel mode to the “NORM” or “WIDE”
position. (For details, refer to page 16.)
4-Speaker Configuration (without the center speaker)
The center speaker is not used in this configuration. If the
program PRO LOGIC is selected, the center sound will be
output from the left and the right main speakers. The program
3 STEREO has no effect in this configuration. However,
the sound effect of other programs can be almost the same as
that of the 5-speaker configuration.
• Be sure to set the center channel mode to the “PHANTOM”
position. (For details, refer to page 16.)
SPEAKER PLACEMENT
The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: main speakers (your normal
stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.
Main: In normal position. (The position of your present
stereo speaker system.)
Rear: Behind your listening position, facing slightly inward.
Nearly 1.8m (approx. 6 feet) up from the floor.
Center: Precisely between the main speakers. (To avoid
interference with TV sets, use a magnetically shielded
speaker.)
Front R
Center
Front L
TV set
Rear R
Rear L
Main L
Main R
Main L Center Center
Main R
Rear L
Rear R
Main L
Main R
Rear L
Rear R
Main L
Main R
Rear
Main L
Main R
Rear
(Two rear speakers)
(One rear speaker)
(Two rear speakers)
(One rear speaker)
Note
As this unit is equipped with a monaural amplifier for the rear channel, sounds output from the rear speakers are in monaual.
So, you may use only one rear speaker instead of using two rear speakers.
However, the use of two rear speakers is recommended when there is more than one listener in the listening room.
When using one rear speaker, place it right behind your listening position.
8
CONNECTIONS
Never plug in this unit and other components until all connections are completed.
CONNECTIONS WITH OTHER COMPONENTS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left)
to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
* If you have YAMAHA components numbered as 1, 3, 4, etc. on the rear panel, connections can be made easily by making sure
to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.
*
1
,
*
2
: See page 10.
FM
ANT
AM
ANT
GND
75Ω
UNBAL.
GND
MONITOR
OUT
VIDEO
VCR
IN OUT
VCR
PHONO VIDEO
PLAY REC IN OUT
1 3 4
VIDEO SIGNAL
TAPE/MD
AUDIO SIGNAL
I20V 60Hz
I00W MAX. TOTAL
SWITCHED
AC OUTLETS
CD
REAR
CENTER
MAIN
SINGLE
:
8
Ω
MIN. /SPEAKER
DUAL
:4
Ω
MIN. /SPEAKER
8
Ω
MIN. /SPEAKER
8
Ω
MIN. /SPEAKER
REAR
CENTER
MAIN
SINGLE
:
6
Ω
MIN. /SPEAKER
DUAL
:3
Ω
MIN. /SPEAKER
6
Ω
MIN. /SPEAKER
4
Ω
MIN. /SPEAKER
SET BEFORE POWER ON
CENTER
MAIN
REAR
SINGLE
REAR
SPEAKERS
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
IMPEDANCE SELECTOR
GND
OUTPUT
VIDEO IN
AUDIO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
LINE OUT
LINE IN
VIDEO OUT
AUDIO OUT
OUTPUT
(U.S.A. model)
To AC outlet
Turntable
LD player,
DVD player, etc.
Video cassette recorder
Tape deck,
MD recorder, etc.
CD player
Monitor TV
*
2
*
1
9
English
CONNECTING SPEAKERS
REAR
CENTER
MAIN
SINGLE
:
8
Ω
MIN. /SPEAKER
DUAL
:4
Ω
MIN. /SPEAKER
8
Ω
MIN. /SPEAKER
8
Ω
MIN. /SPEAKER
REAR
CENTER
MAIN
SINGLE
:
6
Ω
MIN. /SPEAKER
DUAL
:3
Ω
MIN. /SPEAKER
6
Ω
MIN. /SPEAKER
4
Ω
MIN. /SPEAKER
SET BEFORE POWER ON
CENTER
MAIN
REAR
REAR
SINGLE
REAR
SPEAKERS
CAUTION
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
IMPEDANCE SELECTOR
Rear speaker Rear speakerCenter speaker
Main speakers
Left
Right
Left
Right
(U.S.A. model)
Note
Use speakers with the specified impedance
shown on the rear of this unit.
For connecting to the MAIN SPEAKERS terminals
Red: positive (+)
Black: negative (–)
➀
Press the tab.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Release the tab and
secure the wire.
For connecting to the REAR and CENTER SPEAKERS
terminals
Red: positive (+)
Black: negative (–)
➀
Press the tab.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Release the tab and
secure the wire.
➁
➂
➀
How to Connect:
Connect the SPEAKERS terminals to your speakers with wire of the proper gauge (cut as short as possible). If the connections are
faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and –
markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.
Caution
Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or
speakers.
➁
➂
➀
AC OUTLETS (SWITCHED)
(U.S.A., Europe, Canada, China and General models)
.......................................................... 2 SWITCHED OUTLETS
(Australia model).................................. 1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
STANDBY/ON switch or the provided remote control
transmitter’s POWER /I key. These outlets will supply power
to any component whenever this unit is turned on.
The maximum power (total power consumption of components)
that can be connected to the SWITCHED AC OUTLETS is 100
watts.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to the GND
terminal will normally minimize hum, but in some cases better
results may be obtained with the ground wire disconnected.
10
Be sure to switch the position only when the power to this unit
is not on.
Select the position whose requirements your speaker system
meets.
(Upper position)
Rear: If you use one rear speaker, the impedance of the
speaker must be 6Ω or higher.
If you use two rear speakers, the impedance of each
speaker must be 3Ω or higher.
Center: The impedance of the speaker must be 6Ω or higher.
Main: The impedance of each speaker must be 4Ω or
higher.
(Lower position)
Rear: If you use one rear speaker, the impedance of the
speaker must be 8Ω or higher.
If you use two rear speakers, the impedance of each
speaker must be 4Ω or higher.
Center: The impedance of the speaker must be 8Ω or higher.
Main: The impedance of each speaker must be 8Ω or
higher.
IMPEDANCE SELECTOR switch
REAR
CENTER
MAIN
SINGLE
:
8
Ω
MIN. /SPEAKER
DUAL
:4
Ω
MIN. /SPEAKER
8
Ω
MIN. /SPEAKER
8
Ω
MIN. /SPEAKER
REAR
CENTER
MAIN
SINGLE
:
6
Ω
MIN. /SPEAKER
DUAL
:3
Ω
MIN. /SPEAKER
6
Ω
MIN. /SPEAKER
4
Ω
MIN. /SPEAKER
SET BEFORE POWER ON
IMPEDANCE SELECTOR
(U.S.A. model)
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise
this unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE
STANDBY/ON SWITCH IS PRESSED;
The IMPEDANCE SELECTOR switch may not be set to
either end. If so, set the switch to either end when this unit
is in the standby mode.
*
1
*
2
Rear speaker
CENTERREAR
REAR
SINGLE
REAR
SPEAKERS
Note on connecting only one rear speaker:
You can use only one rear speaker in place of two rear
speakers. For connecting one rear speaker, follow the method
shown on the right.
11
English
ANTENNA CONNECTIONS
●
Each antenna should be connected to the designated terminal(s) correctly, referring to the following diagram.
●
Both AM and FM indoor antennas are supplied to this unit. In general, these antennas will provide sufficient signal strength.
Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception
quality only with the indoor antennas, the use of an outdoor antenna may result in improvement.
Connecting the AM loop antenna
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground, which is a metal stake
driven into moist earth.
Notes
●
When connecting the indoor
FM antenna, insert its
connector into the FM ANT
terminal firmly.
●
If you need an outdoor
FM antenna to improve
FM reception quality, either
300-ohm feeder or coaxial cable may be used. In locations
troubled by electrical interference, a coaxial cable is
preferable.
FM
ANT
AM
ANT
GND
75Ω
UNBAL.
➀
➁
➂
Orient so that the best
reception is obtained.
1 2 3
Outdoor FM antenna
Outdoor AM antenna
AM loop
antenna
(included)
Ground
75-ohm/300-ohm
antenna adapter
75-ohm/300-ohm
antenna adapter
75-ohm coaxial cable
300-ohm feeder
Indoor FM
antenna
(included)
(U.S.A. model)
12
CONTROLS AND THEIR FUNCTIONS
FRONT PANEL
STANDBY/ON
NATURAL SOUND AV RECEIVER
PHONES
BASS TREBLE BALANCE
VOLUME
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
55
4
3
2
l
0
l
2
3
4
FM
/
AM
MAN'L
/
AUTO FM
TUNING
MODE
AUTO
/
MAN'L MONO
CENTER
MODE
DOWN
TUNING
UP
EFFECT
MEMORY
EDIT
PROGRAM
A
/
B
/
C
/
D
/
E
1
2 3 4 5 6 7 8
TAPE/MD
MONITOR
VIDEOVCR
TUNER
CD
PHONO
REAR
LEVEL
CENTER
LEVEL
0l0 0l0
1
6789 0 BCEG
I JH
A
FD
23 45
1 STANDBY/ON switch
Press this switch to turn on the power to this unit. Press it
again to turn this unit into the standby mode.
Standby mode
In this state, this unit consumes a very small quantity of
power to receive infrared-signals from the remote control
transmitter.
2 Remote control sensor
Receives signals from the remote control transmitter.
3 Display panel
Shows various information. (For details, refer to page 15.)
4 Input selector buttons
Select a program source to listen to or watch. When a button is
pressed, the name of the selected source appears on the
display.
5 VOLUME control
Used to raise or lower the volume level.
6 PHONES jack
When you listen with headphones privately, connect the
headphones to the PHONES jack and switch off the digital
sound field processor (so that no DSP program name is
illuminated on the display) by pressing the EFFECT button.
You can listen to the sound to be output from the main
speakers through headphones.
PHONES
13
English
7 A/B/C/D/E button
Press this button to select a desired group (A–E) of preset
stations.
8 Preset station number selector buttons
Select a preset station number (1 to 8).
9 Tone controls
These controls are effective only for the sound from the main
speakers.
BASS
Used to increase or decrease the low frequency response.
The 0 position produces flat response.
TREBLE
Used to increase or decrease the high frequency response.
The 0 position produces flat response.
0 BALANCE control
This control is effective only for the sound from the main
speakers.
Adjusts the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
A FM/AM button
Press this button to switch the reception band to FM or AM.
B MEMORY (MAN’L/AUTO FM) button
When this button is pressed, the
“
MEMORY” indicator flashes
for about 5 seconds. While the indicator is flashing, select a
desired preset station number by pressing the corresponding
preset station number selector button to enter the displayed
station into the memory.
When this button is held down for more than 3 seconds, the
automatic preset tuning begins. (For details, refer to page 22.)
C EDIT button
This button is used to exchange the places of two preset
stations with each other.
D TUNING DOWN/UP button
Used for tuning. Press the “UP” side to tune in to higher
frequencies, and press the “DOWN” side to tune in to lower
frequencies.
E TUNING MODE (AUTO/MAN’L MONO) button
Press this button to switch the tuning mode to automatic or
manual. To select the automatic tuning mode, press this
button so that the “AUTO TUNING” indicator lights up on the
display. To select the manual tuning mode, press this button
so that the “AUTO TUNING” indicator goes off.
F EFFECT button
Switches on/off the digital sound field processor (including the
Dolby Pro Logic Surround decoder).
G PROGRAM selector button
When the built-in digital sound field processor (including the
Dolby Pro Logic Surround decoder) is on, this button changes
the currently selected DSP program every time the right or left
side of this button is pressed.
H CENTER MODE button
Selects a center channel output mode (NORM, WIDE or
PHANTOM). (For details, refer to page 16.)
I CENTER LEVEL control
Adjusts the sound output level of the center speaker.
J REAR LEVEL control
Adjusts the sound output level of the rear speakers.
14
For Control of This Unit
1 Tuner keys
Control tuner.
+: Selects higher preset station number.
–: Selects lower preset station number.
A/B/C/D/E: Selects the group (A – E) of preset station
numbers.
2 TEST key
Used for speaker balance adjustment. (For details, refer to
page 16–17.)
3 DSP program selector keys
Select a DSP program. When a key is pressed, the name of
selected program lights up on the display.
4 POWER /I key
Turns the power to this unit on and turns this unit into the
standby mode alternately.
5 SLEEP timer key
This unit is automatically turned into the standby mode one hour
after this key is pressed (so that “SLEEP” indicator lights up).
To cancel this function, press this key again so that “SLEEP”
indicator goes off.
6 Input selector keys
Select input source.
7 DELAY TIME +/– keys
Adjust the delay time, or the time difference between the
begining of source sound and the begining of effect sound.
(For details, refer to page 26.)
8 EFFECT key
Switches on/off the digital sound field processor (including the
Dolby Pro Logic Surround decoder).
9 VOLUME +/– keys
Turn the volume level up/down.
For Other Component Control
Identify the remote control transmitter keys with your
component’s keys. If these keys are identical, their functions
will be the same. On each key function, refer to the
corresponding instruction on your component’s manual.
1 CD player keys
Control compact disc player.
* DISC SKIP is applicable only to compact disc changer.
2 Tape deck keys
Control tape deck.
* DIR A, DIR B and A/B are applicable only to double
cassette tape deck.
* For a single cassette deck with automatic reverse
function, pressing DIR A will reverse the direction of
tape running.
REMOTE CONTROL TRANSMITTER
The remote control transmitter supplied to this unit is designed to control all the most commonly used functions of this unit. If the CD
player and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, this remote control
transmitter will also control various functions of each component.
TEST
—
+
DELAY TIME
PHONO
SKIP CD
DISC SKIP
—
+
TUNER
DIR A
A
/
B
TAPE
VCR
REC/PAUSE
—
+
PRESET
DIR B
VIDEO
EFFECT
VOLUME
PRO LOGIC
ROCK
SUR.
HALL
3 STEREO
DSP
SLEEPPOWER
A
/
B
/
C
/
D
/
E
2
6
8
7
9
4
3
5
1
1
2
15
English
DISPLAY PANEL
1 Multi-information display
Displays various information, for example station frequency,
preset station number and name of selected input source.
2 STEREO indicator
Lights up when an FM stereo broadcast with sufficient signal
strength is received.
3 Signal-level meter
Indicates the signal level of the received station.
If multipath interference is detected, the indication decreases.
4 DSP program indicators
The name of a selected DSP program lights up when the built-
in digital sound field processor and/or the Dolby Pro Logic
Surround decoder is on.
5 MEMORY indicator
When the MEMORY button is pressed, this indicator flashes
for about 5 seconds. While this indicator is flashing, the
displayed station can be programmed to the memory by using
the A/B/C/D/E button and the preset station number selector
buttons.
6 AUTO TUNING indicator
Lights up when this unit is in the automatic tuning mode.
7 TAPE MONITOR indicator
Lights up when the tape deck (or MD recorder etc.) is selected
as the input source by pressing the TAPE/MD MONITOR
button.
8 SLEEP indicator
Lights up while the built-in SLEEP timer is functioning.
9 Center channel mode indicators
The name of a selected center channel mode lights up only
when a program which uses the Dolby Pro Logic Surround
decoder is selected.
0 TEST indicator
Flashes when the built-in test tone generator is functioning
(when the test-tone is output from speakers).
PRESET
kHz
MHz
MEMORY
AM
FM
TAPE
VCR MONITOR
STEREO
0
20
l00
AUTO TUNING
NORMWIDEPHANTOM TEST
SLEEP
PRO LOGIC
3 STEREO
HALL ROCK
ms
1
2
3
4
5
6 7 8 09
16
1
Set to the “
∞
” position.
2 Turn the power on.
3
Set to the “0” position.
4
5 Select the center channel output mode suitable for your
speaker configuration.
(Refer to “SPEAKER CONFIGURATION” on page 7.)
On the feature of each mode, refer to the “Note” shown
below.
Note
In step 5, when you select a center channel output mode,
note the following.
For 5-speaker configuration)
NORM: Select this mode when you use a center speaker
that is smaller than the main speakers. In this
mode, the bass tone will be output from the main
speakers.
WIDE: Select this mode when you use the center
speaker approximately same sized as the main
speakers.
For 4-speaker configuration)
PHANTOM: Select this mode when you do not use the center
speaker. The center sound will be output from
the left and right main speakers.
SPEAKER BALANCE ADJUSTMENT
This procedure lets you adjust the sound output level balance between the main, center, and rear speakers using the built-in test
tone generator. When this adjustment is made, the sound output level heard at the listening position will be the same from each
speaker. This is important for the best performance of the digital sound field processor and the Dolby Pro Logic Surround decoder.
BASS TREBLE
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
STANDBY/ON
TEST
—
+
DELAY TIME
PHONO
SKIP CD
DISC SKIP
—
+
A
/
B
/
C
/
D
/
E
TUNER
DIR A
A
/
B
TAPE
VCR
REC/PAUSE
—
+
PRESET
DIR B
VIDEO
EFFECT
VOLUME
PRO LOGIC
ROCK
SUR.
HALL
3 STEREO
DSP
SLEEPPOWER
1
2
STANDBY/ON
NATURAL SOUND AV RECEIVER
PHONES
BASS TREBLE BALANCE
VOLUME
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
55
4
3
2
l
0
l
2
3
4
FM
/
AM
MAN'L
/
AUTO FM
TUNING
MODE
AUTO
/
MAN'L MONO
CENTER
MODE
DOWN
TUNING
UP
EFFECT
MEMORY
EDIT
PROGRAM
A
/
B
/
C
/
D
/
E
1
2 3 4 5 6 7 8
TAPE/MD
MONITOR
VIDEOVCR
TUNER
CD
PHONO
REAR
LEVEL
CENTER
LEVEL
0l0 0l0
3
4
TEST
ORM.WIDEPHANTOM TEST
CONTINUED
CENTER
MODE
NORM
WIDE
PHANTOM
5
17
English
6 Turn up the volume.
You will hear a test tone (like pink noise) from the left main
speaker, then the center speaker, then the right main
speaker, and then the rear speakers, for about two seconds
each. The display changes as shown below.
* The test tone from the left rear speaker and the right
rear speaker will be heard at the same time.
7 Adjust the BALANCE control so that the effect sound
output level of the left main speaker and the right main
speaker are the same.
8 Adjust the sound output levels of the center speaker and
the rear speakers so that they become almost as same
as those of the main speakers.
9 Cancel the test tone.
Notes
●
Once you have completed these adjustments, you can
adjust whole sound level on your audio system by using
the VOLUME control (or the VOLUME keys on the remote
control transmitter) only.
●
If you use external power amplifiers, you may also use
their volume controls to obtain proper balance.
●
In step 5, if the center channel mode is in the
“PHANTOM” position, the sound output level of the center
speaker cannot be adjusted. This is because in this
mode, the center sound is automatically output from the
left and right main speakers.
Front (L)
Rear
(L and R)
Center
Front (R)
Disappears.
DEPHANTOM TEST
CENTER
LEVEL
0l0
REAR
LEVEL
0l0
STANDBY/ON
NATURAL SOUND AV RECEIVER
PHONES
BASS TREBLE BALANCE
VOLUME
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
55
4
3
2
l
0
l
2
3
4
FM
/
AM
MAN'L
/
AUTO FM
TUNING
MODE
AUTO
/
MAN'L MONO
CENTER
MODE
DOWN
TUNING
UP
EFFECT
MEMORY
EDIT
PROGRAM
A
/
B
/
C
/
D
/
E
1
2 3 4 5 6 7 8
TAPE/MD
MONITOR
VIDEOVCR
TUNER
CD
PHONO
REAR
LEVEL
CENTER
LEVEL
0l0 0l0
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
8
7
6
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
6
9
TEST
—
+
DELAY TIME
PHONO
SKIP CD
DISC SKIP
—
+
A
/
B
/
C
/
D
/
E
TUNER
DIR A
A
/
B
TAPE
VCR
REC/PAUSE
—
+
PRESET
DIR B
VIDEO
EFFECT
VOLUME
PRO LOGIC
ROCK
SUR.
HALL
3 STEREO
DSP
SLEEPPOWER
TEST
18
1
Set to the “
∞
” position.
2 Turn the power on.
3 Select the desired input source by using the input
selector buttons.
(For video sources, turn the TV/monitor ON.)
* The name of the selected input source will appear on
the display.
4 Play the source. (For detailed information on the tuning
operation, refer to page 20.)
5
Adjust to the desired output level.
6 If desired, adjust the BASS, TREBLE and BALANCE
controls (refer to page 19), and use the digital sound
field processor. (Refer to page 25.)
Notes on using the input selector buttons
●
Note that pressing each input selector button selects the
source which is connected to the corresponding input
terminals on the rear panel.
●
The selection of TAPE/MD MONITOR cannot be canceled
by pressing another input selector button. To cancel it,
press TAPE/MD MONITOR again so that the “TAPE
MONITOR” indicator disappears from the display.
When you select a button other than TAPE/MD
MONITOR, make sure that the “TAPE MONITOR”
indicator is not illuminated on the display.
●
If you select the input selector button for a video source
without canceling the selection of TAPE/MD MONITOR,
the playback result will be the video image from the video
source and the sound from the audio tape (or MD etc.).
●
Once you play a video source, its video image will not be
interrupted even if the input selector button for an audio
source is selected.
When you finish using this unit
Press the STANDBY/ON switch on the front panel again or
the POWER /I key on the remote control transmitter to turn
this unit into the standby mode.
BASIC OPERATIONS
TO PLAY A SOURCE
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
TUNER
CD
PHONO
STANDBY/ON
1, 5
2
6
STANDBY/ON
NATURAL SOUND AV RECEIVER
PHONES
BASS TREBLE BALANCE
VOLUME
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
55
4
3
2
l
0
l
2
3
4
FM
/
AM
MAN'L
/
AUTO FM
TUNING
MODE
AUTO
/
MAN'L MONO
CENTER
MODE
DOWN
TUNING
UP
EFFECT
MEMORY
EDIT
PROGRAM
A
/
B
/
C
/
D
/
E
1
2 3 4 5 6 7 8
TAPE/MD
MONITOR
VIDEOVCR
TUNER
CD
PHONO
REAR
LEVEL
CENTER
LEVEL
0l0 0l0
3
From page 18 to 26, this manual describes how to operate this unit mainly by using the front panel control parts.
To operate this unit on the remote control transmitter, use the corresponding keys on the remote control transmitter.
6
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
Страница загружается ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Yamaha RX-V293 Инструкция по применению
- Категория
- Кассетные плееры
- Тип
- Инструкция по применению
Задайте вопрос, и я найду ответ в документе
Поиск информации в документе стал проще с помощью ИИ
на других языках
- English: Yamaha RX-V293 Owner's manual
- français: Yamaha RX-V293 Le manuel du propriétaire
- italiano: Yamaha RX-V293 Manuale del proprietario
- español: Yamaha RX-V293 El manual del propietario
- Deutsch: Yamaha RX-V293 Bedienungsanleitung
- Nederlands: Yamaha RX-V293 de handleiding
- português: Yamaha RX-V293 Manual do proprietário
- dansk: Yamaha RX-V293 Brugervejledning
- polski: Yamaha RX-V293 Instrukcja obsługi
- čeština: Yamaha RX-V293 Návod k obsluze
- svenska: Yamaha RX-V293 Bruksanvisning
- Türkçe: Yamaha RX-V293 El kitabı
- suomi: Yamaha RX-V293 Omistajan opas
- română: Yamaha RX-V293 Manualul proprietarului
Похожие модели бренда
-
Yamaha RX-V493 Инструкция по применению
-
-
-
-
-
-
-
-
-
