Beko WRE6511WBD Руководство пользователя

WRE6511WBD

EN/LV/LT/ET/RU 2820671002

Washing Machine

User Manual

Pesumasin

Kasutusjuhend

Veļas mazgājamā mašīna

Letošanas rokasgrāmata

Skalbimo mašina

Vartotojo vadovas

2820671002

3 / EN Washing Machine / User’s Manual

1 Important instructions for safety and enviroment

This section contains safety instructions that will help protect from risk of personal injury or

property damage. Failure to follow these instructions shall void any warranty.

1.1. General safety

• This product can be used by children at and above 8 years old and by persons whose phy-

sical, sensory or mental capabilities were not fully developed or who lack experience and

knowledge provided that they are supervised or trained on the safe usage of the product

and the risks it brings out. Children must not play with the product. Cleaning and maintenan-

ce works should not be performed by children unless they are supervised by someone.

• Children of less than 3 years should be kept away unless continuously supervised.

• Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the

machine will cause electrical parts to overheat. This will cause problems with your product.

• If the product has a failure, it should not be operated unless it is repaired by the Authorized

Service Agent. There is the risk of electric shock!

• This product is designed to resume operating in the event of powering on after a power inte-

rruption. If you wish to cancel the programme, see “Cancelling the programme” section.

• Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect to have

the grounding installation made by a qualified electrician. Our company shall not be liable

for any damages that will arise when the product is used without grounding in accordance

with the local regulations.

• The water supply and draining hoses must be securely fastened and remain undamaged.

Otherwise, there is the risk of water leakage.

• Never open the loading door or remove the filter while there is still water in the drum.

Otherwise, risk of flooding and injury from hot water will occur.

• Do not force open the locked loading door. The loading door will be ready to open just a

few minutes after the washing cycle comes to an end. In case of forcing the loading door to

open, the door and the lock mechanism may get damaged.

• Unplug the product when not in use.

• Never wash the product by spreading or pouring water onto it! There is the risk of electric

shock!

• Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out

by grabbing the plug.

• Use detergents, softeners and supplements suitable for automatic washing machines only.

• Follow the instructions on the textile tags and on the detergent package.

• The product must be unplugged during installation, maintenance, cleaning and repairing

procedures.

• Always have the installation and repairing procedures carried out by the Authorized Service

Agent. Manufacturer shall not be held liable for damages that may arise from procedures

carried out by unauthorized persons.

• If the power cable is damaged, it must be replaced by the manufacturer, after sales service

or a similarly qualified person (preferably an electrician) or someone designated by the im-

porter in order to avoid possible risks.

• Place the product on a rigid, flat and level surface.

• Do not place it on a long-pile rug or similar surfaces.

• Do not place the product on a high platform or near the edge on a cascaded surface.

• Do not place the product on the power cable.

• Never use sponge or scrub materials. These will damage the painted, chrome plated and

plastic surfaces.

1.2. Intended use

• This product has been designed for domestic use. It is not suitable for commercial use and

it must not be used out of its intended use.

• The product must only be used for washing and rinsing of laundry that are marked accordin-

gly.

• The manufacturer waives any responsibility arisen from incorrect usage or transportation.

1.3 Children’s safety

• Packaging materials are dangerous to children. Keep packaging materials in a safe place

away from reach of the children.

• Electrical products are dangerous for the children. Keep children away from the product

when it is in use. Do not let them to tamper with the product. Use child lock to prevent chil-

dren from intervening with the product.

4 / EN

Washing Machine / User’s Manual

• Do not forget to close the loading door when leaving the room where the product is located.

• Store all detergents and additives in a safe place away from the reach of the children by clo-

sing the cover of the detergent container or sealing the detergent package.

While washing the laundry at high temperatures, the loading door glass

becomes hot. Therefore, keep especially the children away from the loading

door of the machine while the washing operation is in progress.

1.4. Package information

• Packaging materials of the product are manufactured from recyclable materials in accordan-

ce with our National Environment Regulations. Do not dispose of the packaging materials

together with the domestic or other wastes. Take them to the packaging material collection

points designated by the local authorities.

1.5. Disposing of the waste product

• This product has been manufactured with high quality parts and materials which can be

reused and are suitable for recycling. Therefore, do not dispose the product with normal

domestic waste at the end of its service life. Take it to a collection point for the recycling of

electrical and electronic equipment. Please consult your local authorities to learn the nea-

rest collection point. Help protect the environment and natural resources by recycling used

products. For children’s safety, cut the power cable and break the locking mechanism of the

loading door so that it will be non-functional before disposing of the product.

1.6. Compliance with WEEE Directive

This product complies with EU WEEE Directive (2012/19/EU). This product bears a

classification symbol for waste electrical and electronic equipment (WEEE).

This product has been manufactured with high quality parts and materials which

can be reused and are suitable for recycling. Do not dispose of the waste product

with normal domestic and other wastes at the end of its service life. Take it to the

collection center for the recycling of electrical and electronic equipment. Please

consult your local authorities to learn about these collection centers.

Compliance with RoHS Directive:

The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not

contain harmful and prohibited materials specified in the Directive.

2 Installation

Refer to the nearest Authorised Service Agent for installation of the product. To make the product

ready for use, review the information in the user manual and make sure that the electricity,

tap water supply and water drainage systems are appropriate before calling the Authorized

Service Agent. If they are not, call a qualified technician and plumber to have any necessary

arrangements carried out.

CPreparation of the location and electrical, tap water and waste water installations at the place of

installation is under customer's responsibility.

BWARNING: Installation and electrical connections of the product must be carried out by the

Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from

procedures carried out by unauthorized persons.

AWARNING: Prior to installation, visually check if the product has any defects on it. If so, do not

have it installed. Damaged products cause risks for your safety.

CMake sure that the water inlet and discharge hoses as well as the power cable are not folded,

pinched or crushed while pushing the product into its place after installation or cleaning

procedures.

2.1. Appropriate installation location

• Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.

• Total weight of the washing machine and the dryer -with full load- when they are placed on top

of each other reaches to approx 180 kilograms. Place the product on a solid and flat floor that

has sufficient load carrying capacity!

• Do not place the product on the power cable.

• Do not install the product at places where temperature may fall below 0°С.

• Place the product at least 1 cm away from the edges of other furniture.

5 / EN Washing Machine / User’s Manual

2.2. Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement.

Remove the packaging reinforcement by pulling the ribbon.

2.3. Removing the transportation locks

AWARNING: Do not remove the transportation locks before taking out the packaging

reinforcement.

AWARNING: Remove the transportation safety bolts before operating the washing machine!

Otherwise, the product will be damaged.

1. Loosen all the bolts with a suitable spanner until they rotate freely (C).

2. Remove transportation safety bolts by turning them gently.

3. Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)

CKeep the transportation safety bolts in a safe place to reuse when the washing machine needs to

be moved again in the future.

Never move the product without the transportation safety bolts properly fixed in place!

2.4. Connecting water supply

CThe water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is

necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your

machine run smoothly. Attach a pressure reducing valve if water pressure is higher.

CIf you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must

install the supplied stopper to the hot water valve before operating the product. (Applies for the

products supplied with a blind stopper group.)

AWARNING: Models with a single water inlet should not be connected to the hot water tap. In such

a case the laundry will get damaged or the product will switch to protection mode and will not

operate.

AWARNING: Do not use old or used water inlet hoses on the new product. It may cause stains on

your laundry.

1. Tighten all hose nuts by hand. Never use a tool when

tightening the nuts.

2. Open the taps completely after making the hose connection to

check for water leaks at the connection points. If any leaks occur,

turn off the tap and remove the nut. Retighten the nut carefully

after checking the seal. To prevent water leakages and damages

caused by them, keep the taps closed when the machine is not

in use.

2.5. Connecting to the drain

• The end of the drain hose must be directly connected to the wastewater drain or to the

washbasin.

AWARNING: Your house will be flooded if the hose comes out of its housing during water

discharge. Moreover, there is risk of scalding due to high washing temperatures! To prevent such

situations and to ensure smooth water intake and discharge of the machine, fix the end of the

discharge hose tightly so that it cannot come out.

6 / EN

Washing Machine / User’s Manual

• The hose should be attached to a height of at least 40

cm, and 100 cm at most.

• In case the hose is elevated after laying it on the floor

level or close to the ground (less than 40 cm above the

ground), water discharge becomes more difficult and

the laundry may come out excessively wet. Therefore,

follow the heights described in the figure.

• To prevent flowing of dirty water back into the machine

and to allow for easy discharge, do not immerse the

hose end nto the dirty water or do not drive it in the

drain more than 15 cm. If it is too long, cut it short.

• The end of the hose should not be bent, it should not be stepped on and the hose must not be

pinched between the drain and the machine.

• If the length of the hose is too short, use it by adding an original extension hose. Length of the

hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the

extension hose and the drain hose of the product must be fitted well with an appropriate clamp

as not to come off and leak.

2.6. Adjusting the feet

WARNING: In order to ensure that the product operates more

silently and vibration-free, it must stand level and balanced on its

feet. Balance the machine by adjusting the feet.

Otherwise, the product may move from its place and cause crushing

and vibration problems.

1. Loosen the lock nuts on the feet by hand.

2. Adjust the feet until the product stands level and balanced.

3. Tighten all lock nuts again by hand.

AWARNING: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.

2.7. Electrical connection

Connect the product to a grounded outlet protected by a 16 A fuse. Our company shall not be

liable for any damages that will arise when the product is used without grounding in accordance

with the local regulations.

• Connection must comply with national regulations.

• Power cable plug must be within easy reach after installation.

• If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified

electrician install a 16 Amp fuse.

• The voltage specified in the “Technical specifications” section must be equal to your mains

voltage.

• Do not make connections via extension cables or multi-plugs.

BWARNING: Damaged power cables must be replaced by the Authorized Service Agents.

Transportation of the product

1. Unplug the product before transporting it.

2. Remove water drain and water supply connections.

3. Drain all water that has remained in the product.

4.Install transportation safety bolts in the reverse order of removal procedure.

CNever move the product without the transportation safety bolts properly fixed in place!

AWARNING: Packaging materials are dangerous to children. Keep packaging materials in a safe

place away from reach of the children.

7 / EN Washing Machine / User’s Manual

3 Preparetion

3.1. Sorting the laundry

• Sort laundry according to type of fabric, colour, and degree of soiling and allowable water

temperature.

• Always obey the instructions given on the garment tags.

3.2. Preparing laundry for washing

• Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons

will damage the machine. Remove the metal pieces or wash the clothes by putting them in a

laundry bag or pillow case.

• Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets

inside out and brush. Such objects may damage the product or cause noise problem.

• Put small size clothes such as infant’s socks and nylon stockings in a laundry bag or pillow

case.

• Place curtains in without compressing them. Remove curtain attachment items.

• Fasten zippers, sew loose buttons and mend rips and tears.

• Wash “machine washable” or “hand washable” labeled products only with an appropriate

programme.

• Do not wash colours and whites together. New, dark coloured cottons release a lot of dye.

Wash them separately.

• Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.

• Use only dyes/colour changers and limescale removers suitable for machine wash. Always

follow the instructions on the package.

• Wash trousers and delicate laundry turned inside out.

• Keep laundry items made of Angora wool in the freezer for a few hours before washing. This

will reduce pilling.

• Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely

must be shaken off before placing into the machine. Such dusts and powders on the laundry

may build up on the inner parts of the machine in time and can cause damage.

3.3. Things to be done for energy saving

Following information will help you use the product in an ecological and energy-efficient manner.

• Operate the product in the highest capacity allowed by the programme you have selected, but

do not overload; see, “Programme and consumption table”.

• Always follow the instructions on the detergent packaging.

• Wash slightly soiled laundry at low temperatures.

• Use faster programmes for small quantities of lightly soiled laundry.

• Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.

• If you plan to dry your laundry in a dryer, select the highest spin speed recommended during

washing process.

• Do not use detergent in excess of the amount recommended on the detergent package.

3..4 Initial use

Before starting to use the product, make sure that all preparations are made in

accordance with the instructions in sections “Important safety instructions” and

“Installation”.

To prepare the product for washing laundry, perform first operation in Drum

Cleaning programme. If your product is not equipped with Drum Cleaning

programme, perform the Initial Use procedure in accordance with the methods

described under “5.2 Cleaning the loading door and the drum” section of the user

manual.

CUse an detergents suitable for the washing machines.

Some water might have remained in the product due to the quality control processes in the production.

It is not harmful for the product.

3.5. Correct load capacity

The maximum load capacity depends on the type of laundry, the degree of soiling and the

washing programme desired.

The machine automatically adjusts the amount of water according to the weight of the loaded

laundry.

Awarning: Follow the information in the “Programme and consumption table”. When overloaded,

machine's washing performance will drop. Moreover, noise and vibration problems may occur.

3.6. Loading the laundry

1. Open the loading door.

2. Place laundry items loosely into the machine.

3. Push the loading door to close until you hear a locking sound. Ensure that no items are caught

in the door.

8 / EN

Washing Machine / User’s Manual

CThe loading door is locked while a programme is running. The door can only be opened a while after

the programme comes to an end.

Awarning: In case of misplacing the laundry, noise and vibration problems may occur in the machine.

3.7. Using detergent and softener

CWhen using detergent, softener, starch, fabric dye, bleach or limescale remover read the manufacturer's

instructions on the package carefully and follow the suggested dosage values. Use measuring cup if

available.

Detergent, softener and other cleaning agents

• Add detergent and softener before starting the washing programme.

• Never leave the detergent drawer open while the washing programme is running!

• When using a programme without prewash, do not put any detergent into the prewash

compartment (compartment nr. “1”).

• In a programme with prewash, do not put liquid detergent into the prewash compartment

(compartment nr. “1”).

• Do not select a programme with prewash if you are using a detergent bag or dispensing ball.

Place the detergent bag or the dispensing ball directly among the laundry in the machine.

• If you are using liquid detergent, do not forget to place the liquid detergent cup into the main

wash compartment (compartment nr. “2”).

Choosing the detergent type

The type of detergent to be used depends on the type and colour of the fabric.

• Use different detergents for coloured and white laundry.

• Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo,

etc.) used solely for delicate clothes.

• When washing dark coloured clothes and quilts, it is recommended to use liquid detergent.

• Wash woolens with special detergent made specifically for woolens.

A

warning:

Use only detergents manufactured specifically for washing machines.

warning:

Do not use soap powder.

Adjusting detergent amount

The amount of washing detergent to be used depends on the amount of laundry, the degree of

soiling and water hardness.

• Do not use amounts exceeding the dosage quantities recommended on the detergent

package to avoid problems of excessive foam, poor rinsing, financial savings and finally,

environmental protection.

• Use lesser detergent for small amounts or lightly soiled clothes.

Using softeners

Pour the softener into the softener compartment of

the detergent drawer.

• Do not exceed the (>max<) level marking in the

softener compartment.

• If the softener has lost its fluidity, dilute it with

water before putting it in the detergent drawer.

Using liquid detergents

If the product contains a liquid detergent cup:

• Make sure that you have placed the liquid detergent cup in compartment nr. “2”.

• If the liquid detergent has lost its fluidity, dilute it with water before putting in the detergent

cup.

231Detergent Drawer

The detergent drawer is composed of three compartments:

– (1) for prewash

– (2) for main wash

– (3) for softener

– (*) in addition, there is siphon piece in the softener compartment.

2

9 / EN Washing Machine / User’s Manual

• If the liquid detergent has lost its fluidity, dilute it with water before putting in the detergent cup.

If the product does not contain a liquid detergent cup:

• Do not use liquid detergent for the prewash in a programme with prewash.

• Liquid detergent stains your clothes when used with Delayed Start function. If you are going

to use the Delayed Start function, do not use liquid detergent.

Using gel and tablet detergent

Apply the following instructions when using tablet, gel and similar detergents.

• If the gel detergent thickness is fluidal and your machine does not contain a special liquid

detergent cup, put the gel detergent into the main wash detergent compartment during first

water intake. If your machine contains a liquid detergent cup, fill the detergent into this cup

before starting the programme.

• If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it

directly into the drum before washing.

• Put tablet detergents into the main wash compartment (compartment nr. “2”) or directly into

the drum before washing.

CTablet detergents may leave residues in the detergent compartment. If you encounter such a case, place

the tablet detergent between the laundry, close to the lower part of the drum in future washings.

Use the tablet or gel detergent without selecting the prewash function.

Using starch

• Add liquid starch, powder starch or the fabric dye into the softener compartment.

• Do not use softener and starch together in a washing cycle.

• Wipe the inside of the machine with a damp and clean cloth after using starch.

Using bleaches

• Select a programme with prewash and add the bleaching agent at the beginning of the

prewash. Do not put detergent in the prewash compartment. As an alternative application,

select a programme with extra rinse and add the bleaching agent while the machine is

taking water from the detergent compartment during first rinsing step.

• Do not use bleaching agent and detergent by mixing them.

• Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as

it causes skin irritation. Do not pour the bleaching agent onto the clothes and do not use it

for coloured clothes.

• When using oxygen based bleaches, select a programme that washes at a lower

temperature.

• Oxygen based bleaches can be used together with detergents; however, if its thickness is

not the same with the detergent, put the detergent first into the compartment nr. “2” in the

detergent drawer and wait until the detergent flows while the machine is taking in water. Add

the bleaching agent from the same compartment while the machine is still taking in water.

When you want to use liquid detergent, pull the

apparatus towards yourself. The part that falls down

will serve as a barrier for the liquid detergent. If

required, clean the apparatus with water when it

is in place or by removing it. If you will use powder

detergent, the apparatus must be secured at top

position.

When you want to use liquid detergent, press on

the point shown to rotate the apparatus. The part

that falls off will function as a barrier for the liquid

detergent.

If required, clean the apparatus with water when it is

in place or by removing it.

If you will use powder detergent, the apparatus must

be secured at top position.

10 / EN

Washing Machine / User’s Manual

Light colours and whites Colours Dark colours Delicates/Woollens/

Silks

(Recommended

temperature range based

on soiling level: 40-90

°C)

(Recommended

temperature range

based on soiling level:

cold -40 °C)

(Recommended

temperature range

based on soiling

level: cold -40 °C)

(Recommended

temperature range

based on soiling

level: cold -30 °C)

Soiling Level

Heavily

Soiled

(difficult

stains such

as grass,

coffee, fruits

and blood.)

It may be necessary to

pre-treat the stains or

perform prewash. Powder

and liquid detergents

recommended for whites

can be used at dosages

recommended for

heavily soiled clothes. It

is recommended to use

powder detergents to

clean clay and soil stains

and the stains that are

sensitive to bleaches.

Powder and

liquid detergents

recommended for

colours can be

used at dosages

recommended for

heavily soiled clothes.

It is recommended to

use powder detergents

to clean clay and soil

stains and the stains

that are sensitive

to bleaches. Use

detergents without

bleach.

Liquid detergents

suitable for

colours and dark

colours can be

used at dosages

recommended

for heavily soiled

clothes.

Prefer liquid

detergents produced

for delicate clothes.

Woollen and silk

clothes must be

washed with special

woollen detergents.

Normally

Soiled

(For

example,

stains

caused by

body on

collars and

cuffs)

Powder and

liquid detergents

recommended for whites

can be used at dosages

recommended for

normally soiled clothes.

Powder and

liquid detergents

recommended for

colours can be used at

dosages recommended

for normally soiled

clothes. Use detergents

without bleach.

Liquid detergents

suitable for

colours and dark

colours can be

used at dosages

recommended for

normally soiled

clothes.

Prefer liquid

detergents produced

for delicate clothes.

Woollen and silk

clothes must be

washed with special

woollen detergents.

Lightly

Soiled

(No visible

stains exist.)

Powder and

liquid detergents

recommended for whites

can be used at dosages

recommended for lightly

soiled clothes.

Powder and

liquid detergents

recommended for

colours can be used at

dosages recommended

for lightly soiled clothes.

Use detergents without

bleach.

Liquid detergents

suitable for

colours and dark

colours can be

used at dosages

recommended

for lightly soiled

clothes.

Prefer liquid

detergents produced

for delicate clothes.

Woollen and silk

clothes must be

washed with special

woollen detergents.

11 / EN Washing Machine / User’s Manual

9

6

3

4 Operating the product

4.1. Control panel

1 - Programme Selection knob (Uppermost position On / Off)

2 - Spin Speed Indicator LEDs

3 - Child Lock Enabled LED

4 - Door Lock Enabled LED

5 - Delayed Start Indicator LEDs

6 - Programme Follow-up LEDs

7 - Start / Pause Button

8 - Delayed Start Setting Button

9 - Spin Speed Adjustment button

4.2. Preparing the machine

1.Make sure that the hoses are connected tightly.

2.Plug in your machine.

3.Turn the tap on completely.

4.Place the laundry in the machine.

5.Add detergent and fabric softener.

4.3. Programme selection and tips for efficient washing

1.Select the programme suitable for the type, quantity and soiling degree of the laundry in

accordance with the „Programme and consumption table“ and the temperature table below.

2.Select the desired programme with the Programme Selection knob.

12 / EN

Washing Machine / User’s Manual

Programme °C

Maximum load (kg)

Programme Duration (min)

Water consumption (l)

Power consuption (kVt/h)

Spin speed

Cottons

90 6 180 83 1.95 1000

60 6 180 81 1.750 1000

40 6 180 81 0.95 1000

20 6 180 81 0.50 1000

Cottons 60° With Prewash 60 6 200 92 1.80 1000

Eco 40-60

40*** 6 197 49.0 1.050 1000

40*** 3 155 40.0 0.522 1000

40*** 1. 5 155 36.0 0.400 1000

Synthetics

40 2.5 120 66 0.75 1000

Synthetics

20 2.5 120 66 0.25 1000

Mini

30°30 628 60 0.15 1000

Wool / Hand Wash 40°40 1. 5 65 45 0.45 1000

Down Wear 40°40 1. 5 105 85 0.8 1000

Shirts 40°40 2.5 80 42 0.6 800

Drum Clean 90 - 160 67 2.1 600

4.4. Programme and consumption table

***: Eco 40-60 is the test program in accordance with EN 60456:2016/prA:2019 and

energy label with Commission Delegated Regulation (EU) 2019/2014

- : See the programme description for maximum load.

C

Water and power consumption may vary subject to the changes in water pressure, water hardness

and temperature, ambient temperature, type and amount of laundry, spin speed, and changes in

electric voltage.

Depending on the amount of laundry you have loaded into your machine, there may be a

difference of 1-1.5 hours between the duration shown in the Programme and consumption table

and the actual washing duration. Duration will be automatically updated soon after the washing

starts.

Always select the lowest appropriate temperature. The most efficient programmes in terms of

energy consumption are generally those that perform at lower temperatures and longer duration.

Noise and remaining moisture content are influenced by the spinning speed: the higher the

spinning speed in the spinning phase, the higher the noise and the lower the remaining moisture

content.

13 / EN Washing Machine / User’s Manual

Eco 40-60

40 1000 63:17 1,050 49,0 42 62

40 1000 32:35 0,522 40,0 31 62

40 1000 1,5 2:35 0,400 36,0 27 62

Cottons 20 1000 603:00 0,500 81,0 20 62

60 1000 603:20 1,800 92,0 60 62

Synthetics 40 1000 2,5 02:00 0,750 66,0 40 45

Mini 30 1000 600:28 0,150 60,0 23 62

Temperature

selecton (° C)

Spn speed (rpm)

Capacty(kg)

Duraton of the

program (hh:

mm)

Energy

consumpton

(kWh / cycle)

Water

consumpton

(l / cycle)

Washng

temperature (° C)

Resdual

humdty (%)

Consumption Values (EN)

4.5. Main programmes

Depending on the type of fabric, use the following main programmes.

• Cottons 20-40-90

Use this programme for your cotton laundry (sheets, bedlinen, towels, bathrobes, underwear

etc.). Your laundry will be washed with vigorous washing action for a longer washing cycle.

• Synthetics

Use to wash your synthetic clothes (shirts, blouses, synthetic/cotton blends, etc.). Your

laundry will be washed with a gentle action for a shorter washing cycle when compared to the

Cottons programme. For curtains and tulle, it is recommended to use Synthetics 20˚C or 40˚C

programme.

• Woollens / Hand Wash)

Use to wash your woolen/delicate laundry. Your laundry will be washed with a very gentle

washing action in order not to damage the clothes.

4.6. Additional programmes

For special cases, additional programmes are available in the machine.

C

Additional programmes may differ according to the model of the machine.

• Eco 40-60

The Eco 40-60 programme is able to clean normally soiled cotton laundry declared to be

washable at 40 °C or 60 °C, together in the same cycle, and that this programme is used to

assess the compliance with the EU ecodesign legislation.

Although it washes longer than all other programmes, it provides high energy and water

savings. Actual water temperature may be different from the stated wash temperature. When

you load the machine with less laundry (e.g. ½ capacity or less), periods in programme stages

may automatically get shorter. In this case, energy and water consumption will decrease more.

• Cottons 60

Use to wash your normally soiled, durable cotton and linen laundry. Although it washes

longer than all other programmes, it provides high energy and water savings. Actual water

temperature may be different from the stated wash temperature. When you load the machine

with less laundry (e.g. ½ capacity or less), periods in programme stages may automatically

get shorter. In this case, energy and water consumption will decrease more, providing a more

economic wash.

• Cottons 60° with Prewash

Use this programme only for heavily soiled cotton clothes. Add detergent into the prewash

compartment.

14 / EN

Washing Machine / User’s Manual

• Express

Use this programme to wash your lightly soiled cotton clothes in a short time.

• Shirts

This programme is used to wash the shirts made from cotton, synthetic and synthetic

blended fabrics altogether. It reduces wrinkles. Pre-treatment algorithm is executed.

• Apply the pre-treatment chemical on your garments directly or add it together with

detergent when the machine starts to take water from the main washing compartment. Thus

the machine will wash them in a short period of time and expected lifespan of your shirts will

extend.

• Down Wear

Use this programme to wash your coats, vest, jackets etc. containing feathers with a

«machine-washable» label on them. Thanks to special spinning profiles, it is ensured that the

water reaches the air gaps amongst the feathers.

•Drum Clean

Use regularly (once in every 1-2 months) to clean the drum and provide the required hygiene.

Operate the programme while the machine is completely empty. To obtain better results, put

powder lime-scale remover for washing machines into the detergent compartment no. “2”.

When the programme is over, leave the loading door ajar so that the inside of the machine

gets dry.

CThis is not a washing programme. It is a maintenance programme.

Do not run the programme when there is something in the machine. If you try to do so, the

machine detects that there is load inside and aborts the programme.

4.7. Special programmes

For specific applications, select any of the following programmes.

• Rinse

Use when you want to rinse or starch separately.

• Spin+Drain

You can use this function to remove the water on the garment of drain the water in the

machine.

Before selecting this programme, select the desired spin speed and press Start / Pause

button. First, the machine will drain the water inside of it. Then, it will spin the laundry with the

set spin speed and drain the water coming out of them.

If you wish to drain only the water without spinning your laundry, select the Pump+Spin

programme and then select the No Spin function with the help of Spin Speed Adjustment

button. Press Start / Pause button.

C

Use a lower spin speed for delicate laundries.

4.8. Speed selection

Whenever a new programme is selected, the recommended spin speed of the selected

programme is displayed on the spin speed indicator.

To decrease the spin speed, press the Spin Speed Adjustment button. Spin speed decreases

gradually. Then, depending on the model of the product, «Rinse Hold» and «No Spin”

options appear on the display. When “No Spin” is selected, the rinse level indicator lights will

not turn on.

Rinse hold

If you are not going to unload your clothes immediately after the programme completes, you

can use rinse hold function to keep your laundry in the final rinsing water in order to prevent

them from getting wrinkled when there is no water in the machine. Press Start / Pause button

after this process if you want to drain the water without spinning your laundry. Programme will

resume and complete after draining the water.

If you want to spin the laundry held in water, adjust the Spin Speed and press Start / Pause

button.

The programme will resume. Water is drained, laundry is spun and the programme is

completed.

15 / EN Washing Machine / User’s Manual

C

If the programme has not reached the spinning step, you can change the speed without

switching the machine to Pause mode.

4.9. Delayed Start

With the Delayed Start function the end of the programme may be delayed up to 3, 6 or 9

hours.

C

If the programme has not reached the spinning step, you can change the speed without

switching the machine to Pause mode.

1.Open the loading door, place the laundry and put detergent, etc.

2.Select a washing programme and spin speed.

3.Set the desired time by pressing the Delayed Start button. When the button is pressed once,

3 hours delayed end is selected. When the same button is pressed again, 6 hours delay is

selected, and when it is pressed for the third time, 9 hours delayed end is selected. If you

press the Delayed Start button once again, Delayed End function will be canceled.

4.Press Start / Pause button. Previous delayed end time light turns off and next delayed end

time light turns on after every 3 hours.

5.At the end of the countdown, all delayed end lights will turn off and the selected programme

will start.

C

You can switch the machine to pause mode and add laundry during the delayed end period.

Changing the delayed end period

If you want to change the time during countdown, you will need to cancel the programme and

set the delay time again.

Canceling the Delayed End function

If you want to cancel the delayed end countdown and start the programme immediately:

1.Turn the Programme Selection knob to any programme. Thus, Delayed End function will be

canceled. The End/Cancel light flashes continuously.

2.Then, select the programme you want to run again.

3.Press Start / Pause button to start the programme.

4.10. Starting the programme

1.Press Start / Pause button to start the programme.

2.Programme follow-up light showing the startup of the programme will turn on.

4.11. Child Lock

Use Child Lock function to prevent children from tampering with the machine. Thus you can

avoid any changes in a running programme.

C

If the Programme Selection knob is rotated when the child lock is active, "Child Lock Enabled

LED" will flash 3 times. The Child Lock does not allow any change in the programmes or the

selected speed.

Even if another programme is selected with the Programme Selection knob while the Child Lock

is active, previously selected programme will continue running.

When the Child Lock is active and the machine is running, you can switch the machine to Pause

mode without deactivating the Child Lock by turning the Programme Selection knob to On / Off

position. When you turn the Programme Selection knob afterwards, the programme will resume.

To activate the Child Lock:

Press and hold Speed and Delayed Start buttons for 3 seconds. While you are holding for

3 seconds, the «Child Lock Enabled LED» will flash. You can release the buttons when the

LEDs become permanently on.

To deactivate the Child Lock:

Press and hold Speed and Delayed Start buttons for 3 seconds while any programme is

running. While you are holding for 3 seconds, the «Child Lock Enabled LED» will flash. You

can release the buttons when the LED turns off completely.

16 / EN

Washing Machine / User’s Manual

C

In addition to the method above, to deactivate the Child Lock, switch the Programme Selection

knob to On / Off position when no programme is running, and select another programme.

Child Lock is not deactivated after power failures or when the machine is unplugged.

4.12. Progress of programme

Progress of a running programme can be followed from the Programme Follow-up indicator.

At the beginning of every programme step, the relevant indicator light will turn on and light of

the completed step will turn off.

You can change the speed settings without stopping the programme flow while the

programme is running. To do this, the change you are going to make must be in a step after

the running programme step. If the change is not compatible, relevant lights will flash for 3

times.

C

If the machine does not proceed to the spinning step, the Rinse Hold function might be active

or the automatic unbalanced load detection system might be activated due to the unbalanced

distribution of the laundry in the machine.

4.13. Loading door lock

There is a locking system on the loading door of the machine that prevents opening of the

loading door in cases when the water level is unsuitable.

Loading door light will start flashing when the machine is switched to Pause mode. The

machine checks the level of the water inside. If the level is suitable, the Loading Door light

turns off and the loading door can be opened within 1-2 minutes.

If the level is unsuitable, the Loading Door light remains on and the loading door cannot be

opened. If you are obliged to open the Loading Door while the Loading Door light is on, you

must cancel the current programme. See. «Cancelling the programme»

4.14. Changing the selections after programme has started

Switching the machine to pause mode

Press the Start / Pause button to switch the machine to pause mode while a programme

is running. The light of the step which the machine is in starts flashing in the Programme

Follow-up indicator to show that the machine has been switched to the pause mode.

Additionally, when the loading door is openable, the Loading Door light turns off completely.

Changing the speed settings

You can change the speed settings of the programme that is currently running. See «Speed

selection».

C

If no change is allowed, the relevant light will flash 3 times.

Adding or taking out laundry

You can load/unload laundry when a programme is running if the water level is

appropriate to open the door. To do this:

1.Press Start / Pause button to switch the machine to pause mode. The programme follow-up

light of the relevant step during which the machine was switched into the pause mode will

flash.

2.Wait until the Loading Door can be opened.

3. Open the Loading Door and add or take out the laundry.

4.Close the Loading Door.

5. Make changes in speed settings, if necessary.

6. Press Start / Pause button to start the machine.

4.15. Cancelling the programme

To cancel the programme, turn the Programme Selection knob to select another

programme. Previous programme will be cancelled. End / Cancel light will flash

continuously to notify that the programme has been canceled.

Your machine will end the programme when you turn the Programme Selection

knob; however, it does not drain the water inside. When you select and start a new

programme, the newly selected programme will start depending on the step the

17 / EN Washing Machine / User’s Manual

previous programme was canceled in. For example, it may take in additional water or

continue to wash with the water inside.

C

Some programmes may start by discharging the water inside the machine. Depending on the

step where the programme was canceled in, you may have to put detergent and softener again

for the programme you have selected anew.

4.16. End of programme

When the programme ends, «End» LED becomes on at the Programme Follow-up indicator.

1.Wait until the „Door Lock Enabled LED“ goes off completely.

2.To switch off the machine, turn the Programme Selection Knob to On/Off position.

3.Take out your laundry and close the loading door. Your machine is ready for the next washing

cycle.

4.17. Your machine features “Pause Mode”.

After you switch on your machine with the programme selection button (by switching the

button to a different position than the On/Off position), if no programme is started or no

other procedure is performed in the selection step or no action is taken within approx. 2

minutes after the selected programme ends, your machine will switch to energy saving mode

automatically. The brightness of the indicator lights will decrease. Also, if your product has

a display that shows programme time, this display will be completely turned off. If you turn

the Programme Selection knob or touch any button, lights and display will switch back to

previous condition. The selections which you make when exiting from the energy efficiency

may change. Please check the correctness of your selections before starting the programme.

If necessary, please make your settings again. This is not an error.

5 Maintenance and cleaning

Service life of the product extends and frequently faced problems decrease if cleaned at regular

intervals.

5.1. Cleaning the detergent drawer

Clean the detergent drawer at regular intervals (every 4-5 washing

cycles) as shown below in order to prevent accumulation of powder

detergent in time.

Lift the rear part of the siphon to remove it as illustrated.

C

If more than normal amount of water and softener mixture starts to gather in the softener compartment,

clean the siphon.

2 Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin.

Wear protective gloves or use an appropriate brush to avoid touching of the residues in the

drawer with your skin when cleaning.

3 After cleaning, replace the siphon back to its seating and push its front section downwards to

make sure that the locking tab engages.

5.2. Cleaning the loading door and the drum

Residues of softener, detergent and dirt may accumulate in your machine in time and may

cause unpleasant odours and washing complaints. To avoid this, use the Drum Cleaning

programme. If your machine is not featured with Drum Cleaning programme, use Cottons-90

programme and select Additional Water or Extra Rinse auxiliary functions as well. Run the

programme without any laundry in the machine. Before starting the programme, put max. 100

g of powder detergents into the main wash detergent compartment(compartment nr. 2). If the

detergent is in tablet form, put only one tablet into compartment nr. 2. Dry the inside of the

bellow with a clean piece of cloth after the programme has come to an end.

CRepeat Drum Cleaning process in every 2 months.

Use an detergents suitable for the washing machines.

18 / EN

Washing Machine / User’s Manual

After every washing check that no foreign substance is left in the

drum.

If the holes on the bellow shown in the figure is blocked, open the

holes using a toothpick.

CForeign metal substances will cause rust stains in the drum. Clean the stains on the drum surface by

using cleaning agents for stainless steel. Never use steel wool or wire wool.

AWARNING: Never use sponge or scrub materials. These will damage the painted and plastic

surfaces.

5.3. Cleaning the body and control panel

Wipe the body of the machine with soapy water or non-corrosive mild gel detergents as

necessary, and dry with a soft cloth.

Use only a soft and damp cloth to clean the control panel.

5.4. Cleaning the water intake filters

There is a filter at the end of each water intake valve at the rear of the machine and also at the

end of each water intake hose where they are connected to the tap. These filters prevent foreign

substances and dirt in the water to enter the washing machine. Filters should be cleaned as they

do get dirty.

1 Close the taps.

2 Remove the nuts of the water intake hoses to

access the filters on the water intake valves. Clean

them with an appropriate brush. If the filters are

too dirty, take them out by means of pliers and

clean them.

3 Take out the filters on the flat ends of the water

intake hoses together with the gaskets and clean

thoroughly under running water.

4 Replace the gaskets and filters carefully in their

places and tighten the hose nuts by hand.

5.5. Draining remaining water and cleaning the pump filter

The filter system in your machine prevents solid items such as buttons, coins and fabric

fibers clogging the pump impeller during discharge of washing water. Thus, the water will be

discharged without any problem and the service life of the pump will extend.

If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it

is clogged or in every 3 months. Water must be drained off first to clean the pump filter.

In addition, prior to transporting the machine (e.g., when moving to another house) and in case

of freezing of the water, water may have to be drained completely.

19 / EN Washing Machine / User’s Manual

AWARNING: If the product is not in use, turn the tap off, detach the supply hose and drain the water

inside the machine against any freezing possibility in the region of installation.

WARNING: After each use close the supply hose tap of the product.

In order to clean the dirty filter and discharge the water:

1 Unplug the machine to cut off the supply power.

AWARNING: Temperature of the water inside the machine may rise up to 90 ½C. To avoid burning risk,

clean the filter after the water in the machine cools down.

2 Open the filter cap.

3 Some of our products have emergency

draining hose and some does not have.

Follow the steps below to discharge the

water.

Discharging the water when the product has an

emergency draining hose:

a Pull the emergency draining hose out from its

seat

b Place a large container at the end of the

hose. Drain the water into the container by

pulling out the plug at the end of the hose.

When the

container is full, block the inlet of the hose by replacing the plug. After the container is emptied,

repeat the above procedure to drain the water in the machine completely.

c When draining of water is finished, close the end by the plug again and fix the hose in its

place.

d Turn the pump filter to take it out.

Discharging the water when the product does

not have an emergency draining hose:

a Place a large container in front of the filter to

catch water from the filter.

b Loosen pump filter (anticlockwise) until water

starts to flow. Fill the flowing water into the

container you have placed in front of the filter.

Always keep a piece of cloth handy to absorb

any spilled water.

c When the water inside the machine is

finished, take out the filter completely by

turning it.

4 Clean any residues inside the filter as well as fibers, if any, around the pump impeller region.

5 Install the filter.

6 If the filter cap is composed of two pieces, close the filter cap by pressing on the tab. If it is

one piece, seat the tabs in the lower part into their places first, and then press the upper part

to close.

20 / EN

Washing Machine / User’s Manual

CThe model nformaton as stored n the product

database can be reached by enterng followng

webste and searchng for your model dentfer (*)

found on energy label.

https://eprel.ec.europa.eu/

A

Jméno Dodavatele IDENTIFIKÁTOR MODELU (*)

6 Technical specifications

Supplier name or trademark Beko

Model name WRE6511WBD

7329830033

Rated capacity (kg) 6

Maximum spin speed (rpm) 1000

Built-in N/A

Height (cm) 84

Width (cm) 60

Depth (cm) 44

Net weight (±4 kg.) 55

Single Water inlet / Double Water inlet • / -

• Available

Electrical input (V/Hz) 230 V / 50Hz

Total current (A) 10

Total power (W) 1550

Main model cjlt 9213

Страница загружается...

Beko WRE6511WBD Руководство пользователя

Похожие модели бренда

Модели других брендов