Natural Sound Stereo Receiver
Récepteur stéréo “Son Naturel”
RX-V10
CONTENTS
Safety Instructions ...............Inside the Front Cover
Caution ............................................................2
Supplied Accessories ......................................3
Features ..........................................................4
Profile of This Unit ...........................................5
Speaker Setup ................................................6
Connections ....................................................7
Controls and Their Functions ........................12
Speaker Balance Adjustment ........................17
Basic Operations ...........................................20
Tuning Operations .........................................22
Preset Tuning ................................................23
Receiving RDS Stations
<Europe and U.K.models only>..................26
Using Digital Sound Field Processor (DSP)
......................................................................31
Troubleshooting .............................................35
Specifications ................................................36
TABLES DES MATIERES
Caractéristiques ............................................37
Accessoires fournis .......................................37
Attention ........................................................38
Aperçu de cet appareil ..................................39
Installation des enceintes acoustiques ..........40
Raccordements .............................................41
Les commandes et leurs fonctions.................46
Réglage de la balance des enceintes............51
Fonctionnement de base ...............................54
Syntonisation .................................................56
Syntonisation préréglée ................................57
Réception des station RDS
<Modèles pour I’Europe et le Royaume-Uni
seulement
>...................................................60
Utilisation du processeur de champ sonore
numérique (DSP) ........................................65
En cas de difficulté ........................................69
Caractéristiques techniques ..........................70
OWNER’S MANUAL
Thank you for selecting this YAMAHA stereo
receiver.
MODE D’EMPLOI
Nous vous remercions pour avoir porté votre
choix sur ce récepteur stéréo YAMAHA.
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the
manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause
the unit and
cart combination to overturn.
7 Wall or Ceiling Mounting – The unit should be mounted to
a wall or ceiling only as recommended by the
manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat.
10 Power Sources – The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
SAFETY INSTRUCTIONS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
•
Explanation of Graphical Symbols
CAUTION
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
1
English
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
SPECIAL NOTES FOR FCC COMPOSITE
DEVICE (for US customers only)
This device is a composite system. The digital device
component may not cause harmful interference.
19 For US customers only:
Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
FCC INFORMATION (for US customers only)
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring
or distortion – and, most importantly, without affecting your
sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
We Want You Listening For A Lifetime (for US customers only)
2
CAUTION : READ THIS BEFORE OPERATING YOUR UNIT.
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the unit to rain or water.
3. Never open the cabinet. If something drops into the set,
contact your dealer.
4. Do not use force on switches, controls or connection wires.
When moving the unit, first disconnect the power plug and
the wires connected to other equipment. Never pull the
wires themselves.
5. The openings on the cabinet assure proper ventilation of
the unit. If these openings are obstructed, the temperature
inside the cabinet will rise rapidly. Therefore, avoid placing
objects against these openings, and install the unit in well-
ventilated condition. Make sure to allow a space of at least
10 cm behind, on the both sides and above the top panel
of the unit. Otherwise it may not only damage the unit, but
also cause fire.
6. Always set the VOLUME control to “0” before starting the
audio source play. Increase the volume gradually to an
appropriate level after playback has been started.
7. Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding that
the unit is faulty.
9. When not planning to use this unit for long periods of time
(ie., vacation, etc.), disconnect the AC power plug from the
wall outlet.
10.To prevent lightning damage, disconnect the AC power
plug and disconnect the antenna cable when there is an
electrical storm.
11.Grounding or polarization – Precautions should be taken
so that the grounding or polarization of an appliance is not
defeated.
12.AC outlet
Do not connect audio equipment to the AC outlet on the
rear panel if that equipment requires more power than the
outlet is rated to provide.
IMPORTANT
Please record the serial number of this unit in the space
below.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
FOR CANADIAN CUSTOMERS
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT AND FULLY INSERT.
THIS CLASS B DIGITAL APPARATUS MEETS ALL
REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
3
English
AM Loop Antenna
Indoor FM Antenna
Remote Control Transmitter
Batteries (size AA, R6, UM-3)
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER VOLUME
PLAY
DVD/LD
2CH/5CH
PRESET
A/B/C/D/E
–+
LEVEL
DELAY/REAR
/CENTER
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VCR
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are included.
4
FEATURES
●
5 Speaker Configuration
Front: 45W + 45W (8Ω) RMS Output
Power, 0.04% THD, 20–20,000 Hz
Center: 45W (8Ω) RMS Output Power,
0.1% THD, 1 kHz
Rear: 15W (8Ω) RMS Output Power,
0.7% THD, 1 kHz
●
Digital Sound Field Processor
4 Programs for Digital Sound Field
Processing
2 Programs for Dolby Surround Decoding
(DOLBY PRO LOGIC and DOLBY PRO
LOGIC ENHANCED)
●
Automatic Input Balance Control for
Dolby Pro Logic Surround
●
Test Tone Generator for Easier Speaker
Balance Adjustment
●
3 Center Channel Modes
(NORMAL/WIDE/PHANTOM)
● 40-Station Random Access Preset Tuning
● Automatic Preset Tuning
● Preset Station Shifting Capability (Preset
Editing)
● IF Count Direct PLL Synthesizer Tuning
System
● Video Signal Input/Output Capability
● 5-Channel Discrete Input Terminals for
Connecting with a Dolby Digital (AC-3)
Decoder
● SLEEP Timer
● Remote Control Capability
<
Europe and U.K. models only
>
● Multi-Functions for RDS Broadcast
Reception
5
English
PROFILE OF THIS UNIT
You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field
Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to
bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system,
and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on.
In addition, you get incredible realism from sources encoded with Dolby Surround using the built-in Dolby Pro Logic Surround
Decoder.
Please read this operation manual carefully and store it in a safe place for later reference.
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to
the sound of a live performance, but chances are you’ll still
notice something missing: the acoustic environment of the live
concert hall. Extensive research into the exact nature of the
sonic reflections that create the ambience of a large hall has
made it possible for Yamaha engineers to bring you this same
sound in your own listening room, so you’ll feel all the sound of
a live concert.
Furthermore, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of a variety of venues such as an actual concert
hall, theater, etc. to allow you to accurately recreate one of
several actual live performance environments, all in your own
home.
Dolby Pro Logic Surround
This unit employs a Dolby Pro Logic Surround decoder similar
to professional Dolby Stereo decoders used in many movie
theaters. By using the Dolby Pro Logic Surround decoder, you
can experience the dramatic realism and impact of Dolby
Surround movie theater sound in your own home. Dolby Pro
Logic employs a four channel five speaker system. The Pro
Logic Surround system divides the input signal into four levels:
the left and right main channels, the center channel (used for
dialog), and the rear surround sound channels (used for sound
effects, background noise, and other ambient noises). The
center channel allows listeners seated in even less-than-ideal
positions to hear the dialog originating from the action on the
screen while experiencing good stereo imaging.
Dolby Surround is encoded on the sound track of pre-recorded
video tapes, laser discs, and some TV/cable broadcasts. When
you play a source encoded with Dolby Surround on this unit,
the Dolby Pro Logic Surround decoder decodes the signal and
distributes the surround-sound effects.
This Dolby Pro Logic Surround Decoder employs a digital
signal processing system. This system improves the stability of
sound at each channel and minimizes crosstalk between
channels, so that positioning of sounds around the room is
more accurate compared with conventional analog signal
processing systems.
In addition, this unit features a built-in automatic input balance
control. This always assures you the best performance without
manual adjustment.
Manufactured under license from Dolby Laboratories Licensing
Corporation. “Dolby”, the double-D symbol and “Pro Logic” are
trademarks of Dolby Laboratories Licensing Corporation.
Dolby Pro Logic Surround + DSP
Dolby Surround sound system shows its full ability in a large
movie theater, because movie sounds are originally designed
to be reproduced in a large movie theater using many
speakers. It is difficult to create a sound environment similar to
that of a movie theater in your listening room, because the
room size, materials of inside walls, the number of speakers,
etc. of your listening room is much different from those of a
movie theater.
Yamaha DSP technology made it possible to present you with
nearly the same sound experience as that of a large movie
theater in your listening room by compensating for lack of
presence and dynamics in your listening room with its original
digital sound fields combined with Dolby Surround sound field.
The combination of Dolby Pro Logic Surround and DSP is used
on the sound field program “ PRO LOGIC ENHANCED”.
6
SPEAKER SETUP
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with
this unit are front speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker
Configuration” shown below.)
The front speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your
present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center
sounds (dialog etc.) within programs encoded with Dolby Surround. The center speaker needs to be equal in power to the front
speakers, although the rear speakers should not be equal. However, all the speakers should have high enough power handling to
accept the maximum output of this unit.
SPEAKER CONFIGURATION
5-Speaker Configuration
This configuration is the most effective and recommended one.
In this configuration, the center speaker is necessary as well as
the rear speakers. If the program DOLBY PRO LOGIC or
DOLBY PRO LOGIC ENHANCED is selected, conversations
will be output from the center speaker and the ambience will be
excellent.
• Set the center channel mode to the “NORMAL” or “WIDE”
position. (For details, refer to page 18.)
4-Speaker Configuration
The center speaker is not used in this configuration. If the
program DOLBY PRO LOGIC or DOLBY PRO LOGIC
ENHANCED is selected, the center sound is output from the
left and the right front speakers. However, the sound effect of
other programs can be the same as that of the 5-speaker
configuration.
• Be sure to set the center channel mode to the “PHANTOM”
position. (For details, refer to page 18.)
SPEAKER PLACEMENT
The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: front speakers (your normal
stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.
Front: In normal position. (The position of your present
stereo speaker system.)
Rear: Behind your listening position, facing slightly inward.
Nearly six feet (approx. 1.8 m) up from the floor.
Center: Precisely between the front speakers. (To avoid
interference with TV sets, use a magnetically shielded
speaker.)
Front L Center Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L
Rear R
Front L Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L Rear R
Front R
Center
Front L
TV set
Rear R
Rear L
7
English
CONNECTIONS
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
CONNECTIONS WITH OTHER COMPONENTS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left)
to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
* If you have YAMAHA components numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making sure
to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.
*
: Refer to “ABOUT THE ACCESSORY TERMINALS” on page 10.
CENTER
MONITOR
OUT
MAIN
REAR
CENTER
REAR
8
Ω
MIN.
/SPEAKER
OUT
SUBWOOFER
SURROUND
DVD/LD 5CH DISCRT INPUT
IN
OUT
VCR
IN
PHONO
TAPE
GND
CD
OUT
VCR
GND
FM
ANT
75
Ω
UNBAL.
AM
ANT
DVD
/LD
1
TAPE
PB
3
REC
OUT
4
AUDIO SIGNAL SPEAKERS
VIDEO
SIGNAL
B
A
AC OUTLETS
DVD
/LD
VIDEO IN
GND
OUTPUT
AUDIO OUT
VIDEO OUT
AUDIO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
OUTPUT
LINE OUT
LINE IN
I20V 60Hz
I00W MAX. TOTAL
SWITCHED
(U.S.A. model)
To AC outlet
Turntable LD player etc. Video cassette recorder
Tape deck CD player Monitor TV
*
*
Connecting with a Dolby Digital (AC-3) Decoder
If you have a Dolby Digital (AC-3) Decoder unit or an LD player etc. which incorporates a Dolby Digital (AC-3) Decoder, its discrete
outputs can be connected to this unit.
8
Notes
• The laserdisc player with AC-3 RF output (or another unit
with AC-3 RF output) must be also connected to the DVD/LD
AUDIO SIGNAL input terminals of this unit for playing a
source with the Dolby Pro Logic Surround decoded or in
normal stereo (or monaural).
• The discrete signals input to this unit cannot be recorded by
a tape deck or VCR. To record a source played on the
laserdisc player with AC-3 RF output (or another unit with
AC-3 RF output), it must be connected to the DVD/LD
AUDIO/VIDEO SIGNAL input terminals of this unit.
CENTER
MONITOR
OUT
MAIN
SURROUND
DVD/LD 5CH DISCRT INPUT
IN
OUT
VCR
DVD
/LD
IN
PHONO
TAPE
GND
CD
OUT
VCR
GND
FM
ANT
75
Ω
UNBAL.
AM
ANT
DVD
/LD
1
TAPE
PB
3
REC
OUT
4
AUDIO SIGNAL SPEAKERS
VIDEO
SIGNAL
OUTPUT
MAIN CENTER SURROUND
SUBWOOFER
AC-3 RF
OUT
AC-3 RF
IN
VIDEO OUT
AUDIO OUT
Dolby Digital (AC-3) Decoder unit
Laserdisc player with AC-3 RF output or
another unit with AC-3 RF output
9
English
CONNECTING SPEAKERS
MAIN
REAR
CENTER
REAR
8
Ω
MIN.
/SPEAKER
OUT
SUBWOOFER
SURROUND
DVD/LD 5CH DISCRT INPUT
SPEAKERS
B
A
I00W MAX TOTAL
Note
Use speakers with the specified impedance shown on the rear
of this unit.
Note on front speaker connections:
One or two speaker systems can be connected to this unit. If
you use only one speaker system, connect it to either the
SPEAKERS A or B terminals.
Note on a subwoofer connection:
You may wish to add a subwoofer to reinforce the bass
frequencies.
Connect the SUBWOOFER OUT terminal of this unit to the
INPUT terminal of the subwoofer amplifier, and connect the
speaker terminals of the subwoofer amplifier to the subwoofer.
With some subwoofers, including the Yamaha Active Servo
Processing Subwoofer System, the amplifier and subwoofer
are in the same unit.
* The SUBWOOFER OUT terminal is for output to a monaural
amplifier driving a subwoofer. Only frequencies below 200
Hz from the front and center channels are output.
Rear speaker Rear speaker
Center speaker
Front speakers B
Left
Right
Left
Right
Front speakers A
Subwoofer system
Left
Right
10
For connecting to the FRONT SPEAKERS terminals
Red: positive (+)
Black: negative (–)
➀
Unscrew the knob.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Tighten the knob and
secure the wire.
<U.S.A. and General models only>
Banana Plug connections are also possible. Simply insert the
Banana Plug connector into the corresponding terminal.
For connecting to the REAR and CENTER SPEAKERS
terminals
Red: positive (+)
Black: negative (–)
➀
Press the tab.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Release the tab and
secure the wire.
➁
➂
➀
1
2
3
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S) (SWITCHED)
(U.S.A., Europe and General models)
.......................................................... 2 SWITCHED OUTLETS
(U.K. model) ........................................ 1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLET(S) is 100 watts.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to the GND
terminal will normally minimize hum, but in some cases better
results may be obtained with the ground wire disconnected.
Note
Even if you make this connection, never fail to make other wire
connections to this terminal. (See page 11.)
How to Connect:
Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are
faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and –
markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.
Caution
Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage
this unit and/or speakers.
11
English
ANTENNA CONNECTIONS
●
Each antenna should be connected to the designated terminals correctly, referring to the following diagram.
●
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
Connecting the AM loop antenna
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is
a metal stake driven into moist earth.
Notes
●
When connecting the indoor
FM antenna, insert its
connector into the FM ANT
terminal firmly.
●
If you need an outdoor
FM antenna to improve
FM reception quality, either
300-ohm feeder or coaxial cable may be used. In locations
troubled by electrical interference, coaxial cable is
preferable.
IN
PHONO
TAPE
GND
CD
OUT
VCR
GND
FM
ANT
75
Ω
UNBAL.
AM
ANT
DVD
/LD
1
TAPE
PB
3
REC
OUT
4
AUDIO SIGNAL
➀
➁
➂
Orient so that the best
reception is obtained.
1 2 3
Outdoor FM antenna
Outdoor AM antenna
AM loop
antenna
(included)
Ground
75-ohm/300-ohm
antenna adapter
75-ohm/300-ohm
antenna adapter
75-ohm coaxial cable
300-ohm feeder
Indoor FM
antenna
(included)
12
CONTROLS AND THEIR FUNCTIONS
FRONT PANEL
1 POWER switch
Press this switch to switch the power on. Press it again to
switch the power off.
2 Power indicator
<Europe, U.K. and General models only>
Lights up fully while the power is on.
* Standby mode
While the power is on, pressing the POWER key on the
remote control transmitter switches the unit to the standby
mode. In this mode, the power indicator is half illuminated.
3 Remote control sensor
Receives signals from the remote control transmitter.
4 Display panel
Shows station frequencies and various information. (Refer to
page 16 for details.)
5 INPUT selector
Selects a program source to listen to and/or watch. When
turned, the name of a selected source appears on the display.
PTY SELECTOR
<Europe and U.K. models only>
When this unit is in the PTY SEEK mode, turning this control
changes the currently selected program type.
6 VOLUME control
Used to raise or lower the volume level.
7 Control door
See page 13 for how to open and close the control door.
8 PHONES jack
When you listen with headphones, connect the headphones to
the PHONES jack. You can listen to the sound to be output
from the front speakers through headphones.
When listening with headphones privately, set both the
SPEAKERS A and B switches to the OFF position and switch
off the digital sound field processor (so that no DSP program
name is illuminated on the display) by pressing the EFFECT
key.
9 SPEAKERS switches
Set the switch A or B (or both A and B) for the front speaker
system (connected to this unit) you will use to the ON position.
Set the switch for the front speaker system you will not use to
the OFF position.
Parts in the shaded areas are provided for Europe and U.K. models only.
The power indicator (
2) is provided for Europe, U.K. and General models only.
SPEAKERS
OFFON
B
A
A/B/C/D/E
PRESET STATIONS
TUNING
KEY MODE
TUNING
MODE
FM/AM MEMORY PROGRAM
CENTER
MODE
EDIT
AUTO/MAN’L MONO MAN’L/AUTO FM
BASS TREBLE BALANCE
0
–+
0
–+
LR
INPUT
DVD-LD/ VCR / TAPE /CD / TUNER/ PHONO
VOLUME
0I0
POWER
PHONES
NATURAL SOUND STEREO RECEIVER
RX–V10
RDS MODE/FREQ
EON
PTY SEEK
MODE START
PTY SELECTOR
123 4
FG
56
ABC E79= D JK LHI
M8
5CH/2CH
PHONES
13
English
0 RDS MODE/FREQ button
<Europe and U.K. models only>
When an RDS station is received, pressing this button changes
the display mode into the PS mode, PTY mode and/or RT
mode (if the station employs those RDS data services), and
frequency display in turn.
A PTY SEEK MODE button
<Europe and U.K. models only>
When this button is pressed, the unit turns into the PTY SEEK
mode.
B PTY SEEK START button
<Europe and U.K. models only>
Press this button to begin searching for a station after the
desired program type is selected in the PTY SEEK mode.
C EON button
<Europe and U.K. models only>
Press this button to select a desired program type (NEWS,
INFO, AFFAIRS, SPORT) when you want to call a radio
program of that program type automatically.
D FM/AM buttons
Press this button to switch the reception band to FM or AM.
E A/B/C/D/E button
Press this button to select a desired group (A–E) of preset
stations.
F TUNING MODE (AUTO/MAN’L MONO) button
Press this button to switch the tuning mode to automatic or
manual. To select the automatic tuning mode, press this
button so that “AUTO” lights up on the display. To select the
manual tuning mode, press this button so that “AUTO” goes
off.
G MEMORY (MAN’L/AUTO FM) button
When this button is pressed, the MEMO indicator flashes for
about 5 seconds. During this period, select a desired preset
station number by pressing the PRESET STATIONS button
once or more, and then press the MEMORY button once again
to enter the displayed station into the memory.
When this button is pressed and held for about 3 seconds, the
automatic preset tuning begins. (Refer to page 24 for details.)
H PRESET STATIONS/TUNING button
Functions as the PRESET STATIONS button when “PRESET”
is illuminated on the display, and functions as the TUNING
button when “PRESET” is not illuminated on the display.
PRESET STATIONS:
Selects a preset station number (from 1 to 8) whenever the left
or the right side of this button is pressed.
TUNING:
Used for tuning. Press the side to tune in to higher
frequencies, and press the side to tune in to lower
frequencies.
I CENTER MODE button
Selects a center channel output mode (NORMAL, WIDE or
PHANTOM). (For details, refer to page 18.)
J PROGRAM button
Whenever this button is pressed, the built-in digital sound field
processor turns on and the currently selected DSP program
changes sequentially and then the digital sound field processor
turns off, and those are repeated.
K KEY MODE/EDIT button
Whenever this button is pressed, “PRESET” appears and
disappears on the display alternately. This is for switching the
function of the PRESET STATIONS/TUNING button.
This button is also used to exchange the places of two preset
stations with each other.
L Tone controls
BASS
Used to increase or decrease the low frequency response.
The 0 position produces flat response.
TREBLE
Used to increase or decrease the high frequency response.
The 0 position produces flat response.
M BALANCE control
Adjusts the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
Open/close the control door
When it is not necessary to operate controls inside the control door, close the door.
To open the door To close the door
14
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the
CD player and tape deck connected to this unit are YAMAHA components designed for remote control compatibility, then this
remote control transmitter will also control various functions of each component.
For Control of This Unit
1 DELAY/REAR/CENTER and LEVEL +/– keys
Adjust the delay time (DELAY), the rear channel output level
(REAR) and center channel output level (CENTER).
(For details, refer to page 33 and 34.)
2 Program selector keys
PROGRAM:
When the built-in digital sound field processor is on, this key
changes the currently selected DSP program whenever the
right or left side of this key is pressed.
PROLOGIC:
Directly selects the PRO LOGIC program.
ENHANCED:
Directly selects the PRO LOGIC ENHANCED program.
3 Tuner keys
Controls tuner.
+: Selects higher preset station number.
–: Selects lower preset station number.
A/B/C/D/E: Selects the group (A – E) of preset station
numbers.
4 SLEEP timer key
The power to this unit is automatically turned off one hour after
this key is pressed (so that “SLEEP” lights up on the display).
5 POWER key
Turns the power on/off.
*
<Europe, U.K. and General models only>
While the power is on, pressing the POWER key on the
remote control transmitter switches the unit from the
power-on mode to the standby mode, and vice versa. (In
the standby mode, the power indicator on the front panel is
half illuminated.)
6 VOLUME +/– keys
Turns the volume level up/down.
7 Input selector keys
Selects input source.
8 EFFECT ON/OFF key
Switches on/off the digital sound field processor (DSP).
9 TEST key
Used for speaker balance adjustment. (For details, refer to
page 17, 18 and 19.)
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER VOLUME
PLAY
DVD/LD
2CH/5CH
PRESET
A/B/C/D/E
–+
LEVEL
DELAY/REAR
/CENTER
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VCR
1
2
3
4
5
2
8
7
9
6
1
15
English
For Other Component Control
Identify the remote control transmitter keys with your
component’s keys. If these keys are identical, their functions
will be the same. On each key function, refer to the
corresponding instruction on your component’s manual.
1 Tape deck keys
Controls tape deck.
* DIR A, B and A/B are applicable only to double
cassette tape deck.
* For a single cassette deck with automatic reverse
function, pressing DIR A will reverse the direction of
tape running.
2 CD player keys
Controls compact disc player.
* DISC is applicable only to compact disc changer.
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
●
Use only AA, R6, UM-3 batteries for replacement.
●
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
●
Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
●
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
Remote control transmitter operation range
Notes
●
There should be no large obstacles between the remote
control transmitter and the main unit.
●
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid direct
lighting.
1
3
2
30°
30°
Remote control
sensor
Within approximately
6 m (19.7 feet)
16
DISPLAY PANEL
Indicators in the shaded area are provided for Europe and U.K. models only.
1 AUTO indicator
Lights up when this unit is in the automatic tuning mode.
2 MEMO indicator
When the MEMORY button is pressed, this indicator flashes for
about 5 seconds. During this period, the displayed station can
be programmed to the memory by using the A/B/C/D/E button
and the PRESET STATIONS button.
3 Preset station number indicator
Shows the selected group (A–E) and preset station number
(1–8).
4 Multi-information display
Displays various information, for example station frequency
and name of the selected source.
5 STEREO indicator
Lights up when an FM stereo broadcast with sufficient signal
strength is received.
6 Signal-level meter
Indicates the signal level of the received station.
If multipath interfernce is detected, the indication decreases.
7 PTY H (HOLD) indicator
<Europe and U.K. models only>
Lights up while the search is performed in the PTY SEEK
mode.
8 RDS mode indicators
<Europe and U.K. models only>
The name(s) of RDS mode(s) employed by the currently
received RDS station light(s) up. Illumination of the indicator on
the head of a name shows that the corresponding RDS mode
is now selected.
9 EON indicator
<Europe and U.K. models only>
Lights up when an RDS station that employs the EON data
service is received.
0 Program type name indicators
<Europe and U.K. models only>
The name selected in the EON mode lights up.
A DSP program indicators
The name of a selected DSP program lights up when the built-
in digital sound field processor is on.
B Center channel mode indicators
The name of a selected center channel mode lights up only
when the DOLBY PRO LOGIC or DOLBY PRO LOGIC
ENHANCED program is selected.
C TEST indicator
Flashes when the built-in test-tone generator is functioning
(when the test-tone is output from speakers).
D SLEEP indicator
Lights up while the built-in SLEEP timer is functioning.
12
34 56
789
<AB
CD
TEST
PRESET
MEMO
AUTO
PTY H
PTY
PS RT
EON INFO SPORT
NEWS AFFAIRS
ST
0
MHz
l00
FM
SLEEP
WIDE
NORMAL
PHANTOM
CONCERT
HALL
CONCERT
VIDEO
PRO LOGIC
ENHANCED
ROCK
CONCERT
MONO
MOVIE
17
English
1
Set to the “0” position.
2 Select the front speakers to be used.
* If you use two front speaker systems, press both the A
and B switches.
3
Set to the “0” position.
4 Turn the power on.
5 Select the PRO LOGIC or PRO LOGIC
ENHANCED program, so that the corresponding name
lights up on the display.
SPEAKER BALANCE ADJUSTMENT
This procedure lets you adjust the sound output level balance between the front, center, and rear speakers using the built-in test
tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from
each speaker. This is important for the best performance of the digital sound field processor.
The adjustment of each speaker output level should be done at your listening position with the remote control transmitter.
Otherwise, the result may not be satisfactory.
SPEAKERS
OFFON
B
A
BASS TREBLE
0
–+
0
–+
BALANCE
LR
VOLUME
0I0
POWER
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER VOLUME
PLAY
DVD/LD
2CH/5CH
PRESET
A/B/C/D/E
–+
LEVEL
DELAY/REAR
/CENTER
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VCR
5
CONTINUED
1
4
2
3
PROLOGIC
ENHANCED
18
6 Select the center channel output mode suitable for your
speaker configuration.
(Refer to “SPEAKER CONFIGURATION” on page 6.)
On the feature of each mode, refer to the “Note” shown
below.
7
Note
In step 6, when you select the center channel output mode,
note the following.
For 5 speaker configuration)
NORMAL: Select this mode when you use a center speaker
that is smaller than the front speakers. In this
mode, the bass tone will be output from the front
speakers.
WIDE: Select this mode when you use the center speaker
approximately same sized as the front speakers.
For 4 speaker configuration)
PHANTOM: Select this mode when you do not use the center
speaker. The center sound will be output from the
left and right front speakers.
8 Turn up the volume.
You will hear a test tone (like pink noise) from the left front
speaker, then the center speaker, then the right front
speaker, and then the rear speakers, for about two seconds
each. The display changes as shown below.
* The test tone from the left rear speaker and the right
rear speaker will be heard at the same time.
9 Adjust the BALANCE control so that the effect sound
output level of the left front speaker and the right front
speaker are the same.
Flashes continuously.
VOLUME
CENTER
MODE
TEST
TEST
NORMAL
WIDE
PHANTOM
REC/PAUSE
DIR BDIR A
PLAY
DISC
POWER VOLUME
PLAY
DVD/LD
2CH/5CH
PRESET
A/B/C/D/E
–+
LEVEL
DELAY/REAR
/CENTER
TEST
EFFECT
PROGRAM
PROLOGIC
ENHANCED
–+
SLEEP
TAPE
A/B
ON/OFF
TUNER
CD
PHONO
VCR
8
7
9
6
(L and R)
BALANCE
LR
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/