Страница загружается...
SL-07N Cloud
Design. Uniqueness. InnovationsDesign. Uniqueness. Innovations
Техническая
поддержка
User manual
1-34
Инструкция по эксплуатации
35-68
Technical support
SL-07N Cloud
1REV. 2.0 2
Attention!
As a result of continuous upgrades and functionality improvements, technical
characteristics of the device can be changed without any preliminary declaration.
This manual can contain some inaccuracy or misprint. The owner reserves the right to
make corrections to the information described in the user manual and device package.
The last revision of this manual is available on www.slinex.com
Safety instructions
Read and keep that manual.
The device installation process should be carried out by the qulied specialists.
Use the device from –10 ˚C to +55 ˚C, always keep it within that temperature range.
Installation surface should be free from vibration and impact inuence.
Keep this device far from open sources of heat, such as radiators, heaters, and ovens.
The device can be installed near other electronic equipment in case if the temperature of the environment
does not exceed previously mentioned range.
The device should be protected from the direct inuence of the natural phenomena, such as direct
sunlight, rain or snow.
Don’t use aggressive or abradant detergent for the device surface cleaning.
Use soft wet cloth or tissue to remove strong dirt.
Don’t overpower outlets. It can cause re or electric shock.
Nature protection
Don’t throw away the device with other industrial or nutritive trash if you see that
symbol. Some regions have separation and recycling systems for the electronic
equipment. Connect with local authorities to receive information about recycling of
electronic equipment for your region.
Rights and limitation of liability
All rights reserved. Any part of that document can not be published in any form, translated into other
languages or reproduced in any way including electronic or mechanical.
Document recording and copying is strictly denied without owner permission.
Table of contents
1. Package ................................................................................................................................................................................... 3
2. Specication.......................................................................................................................................................................... 3
3. Description............................................................................................................................................................................. 4
4. Installation.............................................................................................................................................................................. 5
4.1. Cable requirements............................................................................................................................................. 5
4.2. Schematic diagrams............................................................................................................................................ 6
4.3. Unit mount ............................................................................................................................................................. 8
5. Operation................................................................................................................................................................................ 9
5.1. Incoming call ......................................................................................................................................................... 9
5.2. Outdoor panel and camera monitoring ...................................................................................................... 10
5.3. Incoming call redirection .................................................................................................................................. 11
5.4. Intercom .................................................................................................................................................................. 12
6. Main menu............................................................................................................................................................................. 12
7. Records playback................................................................................................................................................................. 14
8. Settings.................................................................................................................................................................................... 16
8.1. System settings..................................................................................................................................................... 16
8.2. Door settings ......................................................................................................................................................... 17
8.3. Custom MP3 ringtone ........................................................................................................................................ 18
8.4. Camera settings.................................................................................................................................................... 19
8.5. Network settings .................................................................................................................................................. 20
8.6. Service settings..................................................................................................................................................... 21
8.7. Information............................................................................................................................................................. 21
9. Notication modes.............................................................................................................................................................. 22
10. Photo frame......................................................................................................................................................................... 22
11. Standby clock ..................................................................................................................................................................... 23
12. Network connection diagrams..................................................................................................................................... 24
13. Software................................................................................................................................................................................ 25
13.1. Creating new account...................................................................................................................................... 25
13.2. Wired network connection steps................................................................................................................. 25
13.3. Wireless Wi-Fi network connection steps in «AP mode» ..................................................................... 27
13.4. Wireless Wi-Fi network connection steps in «EZ mode»...................................................................... 28
13.5. Operation.............................................................................................................................................................. 29
13.6. Sharing with the other devices..................................................................................................................... 31
13.7. Notication messages...................................................................................................................................... 32
12. Limited Warranty............................................................................................................................................................... 33
!
SL-07N Cloud
3 4
SCREEN
7”, color IPS
RESOLUTION
1024×600 px.
VIDEO SYSTEM
PAL / NTSC / AHD, TVI, CVI (720p,1080p)
AUDIO TYPE
Half duplex
CALL DURATION
70 seconds
MEMORY
MicroSD card, up to 256 Gb
STANDBY MODE POWER CONSUMPTION
4 W
WORKING MODE POWER CONSUMPTION
8 W
POWER SUPPLY
Built-in power supply, ~100–240 V
MOUNTING TYPE
Surface mount
DIMENSIONS
230×165×22 mm (9.06×6.50×0.87")
WORKING TEMPERATURE
10 ... +55 ˚C (+14...+131 ˚F)
3. Description
1. Package
SL-07N Cloud indoor monitor − 1 pc.
External antenna− 1 pc.
Wall mounting bracket − 1 pc.
Connection wires kit − 1 pkg.
Mounting screws and anchors kit − 1 pkg.
User manual − 1 pc.
165 mm
230 mm 22
mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Power LED. Active when the power is on;
First door panel LED. Active when the rst door panel is on;
Second door panel LED. Active when the second door panel is on;
Display;
«Up» button – increase talking volume, system settings menu cursor movement,
parameter increase inside settings menu;
«Down» button – decrease talking volume, system settings menu cursor movement,
parameter decrease inside settings menu;
Speaker (on the back side of the monitor);
«Settings» button:
• press this button in standby mode to enter system settings menu;
• press this button on parameter inside system settings menu to change its value.
Then press it again to confirm the changes;
«Intercom» button – call another monitor or incoming call redirection;
«Monitor» button – door panel or camera image monitoring;
«Answer» button – incoming call answer and start talking with the visitor;
«Unlock» button – door unlocking;
MicroSD memory card slot (on the side of the monitor);
«Hang Up» button – stop conversation with the visitor / exit current menu;
Microphone.
5
1 2 3 4
6
7
8
9
10
11
12
13
14
15
Door 1
Door 2
Camera 1
Camera 2 Output
Ext. power
Network
4.2. Schematic diagrams
Diagram 1. Outdoor panels, cameras and locks connection.
SL-07N Cloud
5 6
SL-07N Cloud (Master)
GND
+13,5 V
*
4. Installation
4.1. Cable requirements
Disconnect all power cables before device installation.
able type that is used for device connection depends on the distance between the last indoor monitor in
the system and outdoor panel:
) Use 4-wire cable with such parameters:
• distance up to 25 meters (82 ft.) use a cable with 0,22 mm square of one wire (AWG 24);
• distance 25 to 50 (82-164 ft.) meters use a cable with 0,41 mm square of one wire (AWG 21);
• distance 50 to 100 meters (164-328 ft.) use a cable with 0,75 mm square of one wire (AWG 18).
b) If the distance between door monitor and door panel is between 80 and 100 meters (262-328 ft.) then
use a 3-wire cable with 0,75 mm (AWG 18) square of one wire and RG-59 or RG-6 coaxial cable for the
video signal.
c) Shielded or non-shielded twisted pair (not recommended):
• distance up to 25 meters (82 ft.) non-shielded twisted pair can be used;
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
0 - 50 m
Shield
Shield
50 - 80 m
80 - 100 m
RG-59 or RG-6
0 - 25 m
25 - 50 m
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Shield Shield
164 - 262 ft.
0 - 164 ft.
262 - 328 ft.
0 - 82 ft.
82 - 164 ft.
Outdoor
panel 1
Outdoor
panel 2
Lock Lock power
supply
Lock Lock power
supply
Power
Audio
GND
Video
Power
Audio
GND
Video
Not used
Alarm
GND
Video
Not used
Alarm
GND
Video
Video
GND
GND
+12 V
Video
GND
GND
+12 V
CCTV 2
CCTV 1
Camera
power
suppply
Camera
power
suppply
Motion
sensor
Motion
sensor
RJ-45 connector
Door 1
Door 2
Camera 1
Camera 2 Output
Ext. powerNetwork
SL-07N Cloud (Master)
Door 1
Door 2
CCTV 1
CCTV 2
Input
Output
Ext. power
Door 1
Door 2
CCTV 1
CCTV 2
Input
Output
Ext. power
Diagram 2. SL-07IPHD and Sonik 7 monitors connection into one system.
SL-07N Cloud
7 8
Sonik 7 (Slave)
Sonik 7 (Slave)
4.3. Unit mount
1) Take the surface mount bracket from the kit and place it on 150-160 cm height.
2) Mark and drill four halls in the wall.
3) Take four anchors from the kit and hammer them into the drilled halls.
4) Fix surface mount bracket on the wall with four screws from the kit.
5) Connect all communication wires and x the monitor on the surface mount bracket.
Notes:
* Use «Power» plug to connect external power supply +13,5 V. While use external power supply please
keep main power cord ~100-240 V disconnected from the outlet, otherwise it can damage monitor
circuits.
** Outdoor panels, cameras, power supplies, locks and motion sensors illustrated on the diagrams are
optional devices and aren’t included into monitor kit.
Audio
GND
Data
Video
Audio
GND
Data
Video
Audio
GND
Data
Video
SL-07N Cloud
9 10
5.2. Outdoor panel and camera monitoring
Standby mode
Monitor will display
the image from the
rst door panel
(monitoring time – 60 seconds)
Monitor will display
the image from the
second door panel
(monitoring time – 60 seconds)
Press «Monitor»
button on the
monitor
5. Operation
5.1. Incoming call
Standby mode
Standby mode
Melody is ringing on the
monitor and door panel,
image from the door panel
appears on the monitor screen
Visitor presses call button
on the rst door panel
Visitor presses call button
on the second door panel
Press «Answer» button to start
conversation with the visitor
Melody stops ringing and
conversation starts,
talking time is 120 seconds
Press «Hang up» button to
stop conversation or
incoming call
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock
Note:
Monitor will be automatically switched into standby mode if the user doesn’t answer incoming call
during 30 seconds;
Standby mode
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Monitor will display
the image from the
rst CCTV camera
(monitoring time – 60 seconds)
Monitor will display
the image from the
second CCTV camera
(monitoring time – 60 seconds)
Press «Hang up» button to
stop monitoring or
conversation
Press «Answer» button to start
conversation with the visitor
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock
SL-07N Cloud
11 12
5.4. Intercom
Two monitors are connected into one system.
Melody starts
ringing on the
other monitor
Standby mode
5.3. Incoming call redirection
Two monitors are connected into one system.
Notes:
1) If several monitors connected into one system, the user can view the image from door panels on any
monitor inside this system. The image will be transferred from the «Master» monitor outdoor panels to
the «Slave» monitors.
2) If somebody press call button on the outdoor panel while monitoring is active then the image from
this outdoor panel appears on the monitor screen and call melody starts. Press «Answer» button
to start conversation with the visitor.
Note:
If incoming call was successfully redirected to the other monitor and other user answered the call then
current monitor will enter standby mode.
Melody starts ringing on
the other monitor inside
the system and visitor image
appears on the monitor screen
Conversation with the
visitor on the other
monitor begins
Incoming call from the
outdoor panel and user
started conversation
Press «Intercom»
button to start
call redirection
Note:
If someone press call button on the door panel while intercom is active then the image from this door
panel appears on the monitor screen and call melody starts. Press «Answer» button to start
conversation with the visitor.
6. Main menu
Press button in standby mode to enter main menu. Use or buttons to move through
the settings. Press button again to enter current setting. Then press or button to change
current parameter value and approve the setting by pressing button.
Press button on the keyboard or move to icon and press button to exit from the
current menu.
Press «Answer» button on the
other monitor to start
conversation with the visitor
Standby mode
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock
Press «Hang up» button to
stop conversation or
incoming call
Standby mode
Conversation with the
other monitor starts
Press «Answer» button on
the other monitor to start
conversation
Press «Hang up»
button to stop
conversation
Intercom
Press «Intercom»
button to start
intercom call
Intercom
Door 1
REC
− +
− +
− +
− +
08
35
27
29
13 14
SL-07N Cloud
7. Records playback
Press «Records» icon in the main menu to enter records playback menu:
Following folders are available in the «Records» menu:
Call records − incoming call video records viewing;
Message records − voice records from outdoor panel if nobody is at home;
Motion records − software motion detection video records;
Alarm records − hardware motion detection video records using external sensors .
Current video channel
Image and
volume
settings bar
Decrease current
parameter value Increase current
parameter value
Enable/disable
image and volume
settings bar
Start/stop
video recording
Image monitoring screen has following elements:
Records
Records
Settings
Intercom
Photo frame
Monitoring
At home
06-10-2021 12 : 01
Motion records
Message records
Call records
Alarm records
Camera1
Door2
Door1
Camera2
06-10-2021 12 : 01
Main menu
Monitoring
REC
Main menu
Outdoor panels and cameras monitoring is available directly from the main menu of the monitor by
choosing corresponding icons:
Door1 − door 1 image monitoring;
Door1 − door 2 image monitoring;
Camera1 − camera 1 image monitoring;
Camera1 − camera 2 image monitoring.
Main menu
Take a
snapshot
SL-07N Cloud
15 16
Main menu
Records
Call records
Message records
Motion records
Alarm records
Next page Exit folderPrevious page
Record
playback
2019/09/18 15:40:42
Press icon on the right side of the file name to start current file playback. Also you can stop playback,
delete current le, set up volume or get back to the list of video les using the buttons on the bottom of
the screen:
− start/stop playback;
− previous/next le playback;
− delete current le;
− decrease/increase playback volume;
− get back to the les list.
− +
20210105061950_0010_DOOR2.mov
00:00 00:03 7
DOOR2 05/01/2021 06:19:50
−+
8. Settings
8.1. System settings
Press «Settings» icon in the main menu then press «System setting» icon to enter system settings menu:
Following folders are available in the «Settings» menu::
System setting − monitor system settings, language setting, time setting, etc.;
Door setting − outdoor panels video standard setting, melody and motion detection settings;
Camera setting− cameras video standard and motion detection settings;
Network setting− device network settings;
Service − microSD card format, factory default settings and software update;
Information − program software version and UUID identication number.
Main menu
Settings
Camera setting
Network setting
Door setting
Information
System setting
Service
ID
Main menu
Settings
System setting
System setting
Device id 1
Time 08-11-2021 14:55
Date format DD-MM-YY
Standby clock 60 S
Language English
Keytone O’
Key backlight On
Door panel backlight On
Call records (11-1/2)
20210105061950_0010_DOOR2.mov Прочитано
20210105061842_0002_DOOR1.mov Не прочитано
20210105061840_0000_DOOR1.mov Не прочитано
20210105061727_0001_DOOR1.mov Не прочитано
20210105061725_0001_DOOR1.jpg Прочитано
20210105061724_0001_DOOR1.mov Не прочитано
20210105061549_0001_DOOR1.jpg Не прочитано
20210105061548_0001_DOOR1.jpg Не прочитано
20210105061546_0001_DOOR2.jpg Прочитано
20210105061544_0001_DOOR2.jpg Прочитано
( )
( ) ( )
SL-07N Cloud
17 18
Main menu
Settings
Door setting
Main menu → Settings → System
Device ID − this monitor model can only be «Master» in the system;
Time − current date and time settings;
Date format − date format setting;
Standby clock − clock display in standby mode time, from 10 to 180 sec. or Off;
Language − menu language setting;
Keytone − enable/disable screen touching sound;
Key backlight − enable/disable keyboard backlight on the monitor;
Door panel backlight − enable/disable call button backlight on the outdoor panel.
8.2. Door settings
Press «Settings» icon in the main menu then press «Door setting» icon to enter outdoor panels settings:
Main menu → Settings → Door setting
Channel activation − include or exclude current video channel from viewing list;
Signal mode − PAL, NTSC or Automatic;
Signal type − AHD 720P / AHD 1080P / TVI 720P / TVI 1080P /CVI 720P / CVI 1080P / CVBS;
Unlock time − relay unlocking time, from 1 to 10 sec.;
Record mode − record type when incoming call or motion event occurs, «Snapshot» or «Video»;
Motion detection − enable and set the sensitivity of program motion detection;
Motion detection duration − program motion detection recording time;
Motion display − enable/disable screen activation if program motion detection occurs;
Motion ringtone − enable and set the melody if program motion detection occurs;;
Message − time of message recording if «Not at home mode» is activeated;
Ring setting − outdoor panels melody settings;
Door 1
Channel activation On
Signal mode PAL
Signal type AHD1080
Unlock time 2 S
Record mode Video
Motion detection Medium
Motion detection duration 10 S
Motion display On
Motion ringtone O
Message 30 S
Ring setting
Door 1
Door 2
Main menu
Settings
Door setting
Ring setting
Door 1 / Ring 1
Schedule 06 : 00 - 12 : 00
Time 10 Sec
Ring mode Standard
Ring select 4
Ring volume 5
Outdoor panel volume 7
Ring 1
Ring 2
Ring 3
Main menu → Settings → Door setting→ Ring setting
Schedule − time of the day to apply following settings;
Time − incoming call melody ringing time from 5 to 45 sec.;
Ring mode − «Standard» - default melodies from internal memory or «Customize» - choose mp3
melody from the «Ring» folder on microSD card;
Ring select − choose the melody for the current outdoor panel;
Ring volume − set incoming call melody volume level on the monitor, from 0 to 10;
Outdoor panel volume − set call melody volume level on the outdoor panel, from 1 to 10 or O.
8.3. Custom MP3 ringtone
Create «Ring» folder in the root of microSD card, if it isn’t already created by the monitor. Paste MP3 files
you would like to use as a ringtone into this folder. File names must have only English letters and figures in
its names and its quantity must not exceed 8 symbols to be visible on the monitor.
Insert microSD card into the monitor and go to the «Settings» → «Door setting» → «Ring setting» menu.
Then choose «Ring mode» → «Custom» and choose the melody to use as a ringtone in the «Ring select»
menu.
Pay attention that melody is active only for the time period specified in the «Schedule» menu. There are 3
time periods for every outdoor panel specified as «Ring 1», «Ring 2» and «Ring 3» bookmarks on the left
SL-07N Cloud
19 20
Network
Net pairing mode AP mode
Cloud services Unconnected
Wi-Fi hotspot SmartLife-b1e24f
Password 12345678
Main menu → Settings → Camera setting
Channel activation − include or exclude current video channel from viewing list;
Sensor type − type of the sensor connected to the corresponding camera:
«NO», motion sensor with normally disconnected (opened) contacts is used;
«NC», motion sensor with normally connected contacts is used;
«O», motion sensor is not used;
Signal mode − PAL, NTSC or Automatic;
Signal type − AHD 720P / AHD 1080P / TVI 720P / TVI 1080P /CVI 720P / CVI 1080P / CVBS;
Alarm time − alarm time in case of hardware motion detection event, from 1 to 20 sec.;
Alarm record mode − record type when motion event occurs, «Snapshot» or «Video»;
Motion detection − enable and set the sensitivity of program motion detection;
Motion detection duration − program motion detection recording time;
Motion display − enable/disable screen activation if program motion detection occurs;
Motion ringtone − enable and set the melody if program motion detection occurs.
Hardware motion detection can detect motion by means of external device (hardware motion sensor).
There are two types of sensors that can be connected to the monitor: sensor with normally opened
contacts (NO) and sensor with normally closed contacts (NC).
Depending on the type of sensors that are used appropriate settings must be made in the hardware
motion detection settings menu. External sensors connection diagram you can nd on the page 6.
Main menu → Settings → Network setting
Net pairing mode − monitor network connection mode,
«AP mode» – manual Wi-Fi connection mode;
«Cable» – wiring conection to the local network;
«EZ mode» – automatic Wi-Fi connection mode;
Cloud services − cloud server connection status;
Wi-Fi hotspot − hotspot name;
Password − hotspot password;
IP address − device network IP address (available only in «Cable» and «EZ mode»);
MAC − device MAC address (available only in «Cable» and «EZ mode»).
Main menu
Settings
Camera setting
8.4. Camera settings
Press «Settings» icon in the main menu then press «Camera setting» icon to enter camera settings menu:
Camera 1
Channel activation On
Sensor type NO
Signal mode PAL
Signal type AHD1080
Alarm time 4 S
Alarm record mode Video
Motion detection O
Motion detection duration 20 S
Motion display On
Motion ringtone O
Camera 1
Camera 2
Main menu
Settings
Network setting
8.5. Network settings
Press «Settings» icon in the main menu then press «Network setting» icon to enter network settings menu:
SL-07N Cloud
21 22
8.7. Information
Press «Settings» icon in the main menu then press «Information» icon to enter information menu.
Main menu → Settings → Information
Software version − current software version of the monitor;
Release date − software release date;
SD remain space − microSD card installed into monitor slot information;
UUID − unique cloud identification number.
Main menu → Settings → Service
Formatting SD disk − microSD card format;
Factory settings − restore factory default settings of the monitor;
Software update − software update of the monitor. Place update file «update.ius» in microSD root
folder, then choose this menu to start update process;
Restart system − monitor reboot.
Service
Formatting SD disk Ok
Factory settings Ok
Software update Ok
Restart system Ok
Information
Software version 3.0.0.1
Release date 2021-10-21
SD remain space 7.1G/7.2G
UUID *04be4d97
9. Notication modes
Monitor has 3 modes. Depending on the current active mode, sound notications type changes. User can
change current mode by touching corresponding icon in the main menu:
Sound notifications are enabled, both on the monitor and on the outdoor panel;
Sound notifications are disabled on the monitor, but enabled on the outdoor panel;
Visitor can leave voice messages for the user in this mode if corresponding «Message»
function is enabled in the «Settings» → «Door setting» menu;
Sound notifications are disabled, both on the monitor and on the outdoor panel.
Dormant
At home
Not at home
8.6. Service settings
Press «Settings» icon in the main menu then press «Service» icon to enter service settings menu:
Main menu
Settings
Service
Main menu
Settings
Information
10. Photo frame
Create «Digital Frame» folder in the root of microSD card, if it isn’t already created by the monitor. Paste
JPG images you would like to view into this folder. File name must have only English letters and figures in
its name and its length must not exceed 30 symbols to be visible on the monitor .
Note that JPG images resolution must not exceed 2560×1440 pixels. Other image formats and resolutions
are not supprted.
SL-07N Cloud
23 24
Insert microSD card into the monitor slot and press «Photo frame» icon in the main menu to enter photo
frame settings:
Photo frame
Main menu
Photo frame
Photo frame On
Switching time 3 S
Background music O
Background volume 5
Main menu → Photo frame
Photo frame − enable/disable photo frame function in standby mode;
Switching time − photo switching interval, from 3 to 30 sec.;
Background music − enable/disable background music playback in photo frame mode;
Background volume − set background music volume in photo frame mode.
11. Standby clock
If «Standby clock» function is enabled in «Settings» → «System setting» menu then user can see the
folowing screen after exiting from the main menu or conversation ending:
11 : 28
26-10-2021 Вторник
0 22 1
Call records
Message records
Motion records
Alarm records
WAN 1 2 3 4
WAN 1 2 3 4
Android / iOS
Android / iOS
Smart call
Smart call
Smart call
Internet
3G / Wi-Fi
Router
PC
PC
12. Network connection diagrams
Diagram 1. SL-07N Cloud wired network connection.
Diagram 2. SL-07N Cloud wireless Wi-Fi network connection.
Android / iOS
Internet
3G / Wi-Fi
Wi-Fi (LAN)
«AP or EZ mode»
Router
SL-07N Cloud
SL-07N Cloud
SL-07N Cloud
25 26
13. Software
Enter «Google Play» (for Android) or «Apple App Store» (for iOS) and search for «Smart Call» application,
then install this applicationи on your mobile device.
13.1. Creating new account
1) Start «Smart Call» application on your mobile device and press «SIgn up» button to create an account;
2) Choose destination country and enter your Email, then press «Get verication code» button to receive
an Email with verification code;
3) Check the Email, specied on the previous step;
4) Enter 6-digit code from the letter to activate your account. Set your password and press «Finish» to
nalize account creation process. Use your Email as a login for
13.2. Wired network connection steps
1) Use twisted pair CAT5 or CAT6 cable to connect device to the router;
2) Connect mobile device into the same local network;
3) Press «Add device» button and choose device model for connection. Then choose «Cable» connection
type in the upper right corner;
4) Turn on the monitor power and press «Next» button in the application;
5) In the monitor main menu press «Settings» → «Network setting» → «Net pairing mode» set «Cable»
type of connection. Monitor will reboot after exiting «Network» menu. After monitor reboot press
«Next» button in the «Smart Call» application;
6) Enable «Next step» switch then press «Next» button. Network devices search will be started;
7) Choose Sonik7 Cloud device in the list and it will be paired to the current account of the «Smart Call»
application.
SL-07N Cloud
27 28
13.3. Wireless Wi-Fi network connection steps in «AP mode»
1) Connect mobile device into the same Wi-Fi network you want to connect the monitor;
2) Disable 3G/4G internet connection on your mobile device;
3) Press «Add device» button and choose device model for connection;
4) Turn on the monitor power and press «Next» button in the application;
5) In the monitor main menu press «Settings» → «Network setting» → «Net pairing mode» set «AP mode»
type of connection. Monitor will reboot after exiting «Network» menu. After monitor reboot press
«Next» button in the «Smart Call» application;
6) Enable «Next step» switch then press «Next» button;
7) Enter Wi-Fi network name, the monitor will be conected to, and network password. Then press «Next»
button to go to the next step;
8) Press «Go to connect» button and manually conect mobile phone to the Wi-Fi hotspot of the monitor.
Wi-Fi hotspot name is «SmartLife-xxxxxx». Password: 12345678;
9) When mobile phone is connected to the Wi-Fi hotspot, come back to the mobile application. The
monitor will be connected to the Wi-Fi network, specied on the 7-th step and paired to the current
account of the «Smart Call» application.
If current device is already paired to some account in
the «Smart Call» application
, then it
is impossible to add this device to any other account. To add this device to some other
account delete this device in the account, it is currently connected to!
!
13.4. Wireless Wi-Fi network connection steps in EZ mode
1) Connect mobile device into the same Wi-Fi network you want to connect the monitor;
2) Disable 3G/4G internet connection on your mobile device;
3) Press «Add device» button and choose device model for connection. Then choose «EZ mode»
connection type in the upper right corner of the screen;
4) Turn on the monitor power and press «Next» button in the application;
5) In the monitor main menu press «Settings» → «Network setting» → «Net pairing mode» set «EZ mode»
type of connection. Monitor will reboot after exiting «Network» menu. After reboot press «Next»
SL-07N Cloud
29 30
button in the application;
6) Enable «Next step» switch then press «Next» button;
7) Enter Wi-Fi network name, the monitor will be conected to, and network password. Then press «Next»
button to go to the next step;
8) The monitor will be connected to the Wi-Fi network, specied on the 7-th step and paired to the
current account of the «Smart Call» application.
13.5. Operation
Press device icon
to start monitoring
Go to the
main menu
Enable conversation
mode
Outdoor panel 1
Outdoor panel 2
Camera 1
Camera 2
Take a snapshot
Record video
Video channels
switching
Records playback
from the
monitor archive
Mobile phone records
local archive playback
Open lock
(Default password:
888888)
Advanced settings
menu
Enable sound
from the
outdoor panel
Main
settings
Full screen
mode
Main menu Monitoring menu
SL-07N Cloud
31 32
13.6. Sharing with the other devices
The account, device is added for the first time, is master account. This account has master permissions and
can change all the settings. If several mobile phones are going to be used with the same device then
personal account must be created on every mobile phone. Here are the steps to add the same device on
several mobile phones:
1) Create an account on the rst mobile phone application and add your device. Account on this mobile
phone will be the master account for this device;
2) Install «Smart Call» application on every mobile phone that is going to be used and create its own
account in every application. Every mobile phone must use it’s own account in the application;
3) Using master account enter device monitoring screen, press icon on the right upper corner of
the screen and enter «Add sharing» menu. Enter account name, used on the shared device and press
«Done» button on the right upper corner of the screen. Shared account must be added to the sharing
list. It means that the user on the shared mobile phone now have an access to this device;
4) In the same manner add all other mobile devices into sharing list.
Press «Accept» button to start
conversation with the visitor or
«Decline» to hang up incoming
call.
13.7. Notication messages
Press «Me» bookmark on the bottom of the main screen, then press icon on the right upper corner of
the screen and enter «App Notication» menu. Here you can enable or disable notification messages from
the application.
SL-07N Cloud
33 34
14. Limited warranty
Manufacturer guarantees product normal functioning during the warranty period if the user keeps all
safety instructions described in that manual.
Warranty period is 12 months from the moment of the product purchasing (warranty period could be
extended up to 24 months or more, depending on the local regulations).
Warranty period allows user to make guarantee repair in cases when normal functioning of the product
was violated by the fault of manufacturer and the user has not oend transporting, installation and
working conditions.
This limited warranty does not cover any damage to the product that results from improper installation,
accident, abuse, misuse, natural disaster, insucient or excessive electrical supply, abnormal mechanical
or environmental conditions, or any unauthorized disassembly, repair or modication.
Warranty void in such cases:
• the product was damaged by the fault of the customer;
• the product wasn’t properly installed according reccomendations from the manual;
• the sticker on the backside of the product was broken;
• the product was not used for its intended function.
This limited warranty covers only repair, replacement, refund or credit for defective products, as provided
above. Manufacturer is not liable for, and does not cover under warranty, any damages or losses of any
kind whatsoever resulting from loss of, damage to, or corruption of, content or data or any costs
associated with determining the source of system problems or removing, servicing or installing products.
This warranty excludes third party software, connected equipment or stored data. Manufacturer is
therefore not liable for any losses or damage attributable to third party software, connected equipment or
stored data.
In the event a product has been discontinued, manufacturer shall either repair the product, oer to
replace it with a comparable product or provide a refund at the lesser of the purchase price or the
product’s current value.
Repaired or replacement products will continue to be covered by this limited warranty for the remainder
of the original warranty term.
Содержание
1. Комплект поставки............................................................................................................................................................ 37
2. Характеристики.................................................................................................................................................................. 37
3. Описание ............................................................................................................................................................................... 38
4. Установка............................................................................................................................................................................... 39
4.1 Выбор кабеля ........................................................................................................................................................ 39
4.2 Схемы подключения.......................................................................................................................................... 40
4.3 Монтаж..................................................................................................................................................................... 42
5. Эксплуатация ....................................................................................................................................................................... 43
5.1. Вызов с вызывной панели.............................................................................................................................. 43
5.2. Просмотр панелей и камер........................................................................................................................... 44
5.3. Переадресация вызова ................................................................................................................................... 45
5.4. Внутренняя связь ............................................................................................................................................... 46
6. Главное меню....................................................................................................................................................................... 46
7. Просмотр записей............................................................................................................................................................. 48
8. Настройки ............................................................................................................................................................................. 50
8.1. Системные настройки...................................................................................................................................... 50
8.2. Настройки вызывных панелей..................................................................................................................... 51
8.3. Установка пользовательских MP3 мелодий........................................................................................... 52
8.4. Настройки дополнительных камер ........................................................................................................... 53
8.5. Cетевые настройки............................................................................................................................................ 54
8.6. Cервисные настройки...................................................................................................................................... 55
8.7. Информация о системе ................................................................................................................................... 55
9. Режим работы...................................................................................................................................................................... 56
10. Фоторамка.......................................................................................................................................................................... 56
11. Часы в режиме ожидания............................................................................................................................................ 57
12. Схемы подключения домофона к локальной сети .......................................................................................... 58
13. Программное обеспечение........................................................................................................................................ 59
13.1. Создание учетной записи............................................................................................................................ 59
13.2. Подключение к проводной сети............................................................................................................... 59
13.3. Подключение к беспроводной Wi-Fi сети в режиме AP................................................................. 61
13.4. Подключение к беспроводной Wi-Fi сети в режиме EZ.................................................................. 62
13.5. Управление........................................................................................................................................................ 63
13.6. Общий доступ к устройству........................................................................................................................ 65
13.7. Оповещения о входящих вызовах........................................................................................................... 66
14. Условия гарантии............................................................................................................................................................ 67
Указания по безопасности
Прочтите и сохраните эту инструкцию.
Все работы, связанные с установкой данного продукта, должен выполнять квалифицированный
специалист.
Соблюдайте температурный режим, используйте прибор при температуре от -10 ˚C до +55 ˚C.
Устанавливать устройство следует на поверхностях, не склонных к вибрациям или ударным
нагрузкам.
Устанавливайте устройство вдали от открытых источников тепла, таких как радиаторы,
обогреватели и печи.
Допускается установка устройства вблизи других устройств бытовой электроники, если
температура окружающей среды не выходит за границы вышеупомянутых температур.
Устройство должно быть защищено от погодных воздействий, таких как прямой солнечный свет,
вода (дождь) или снег.
Не используйте агрессивные или абразивные моющие средства для чистки корпуса прибора.
Используйте мягкую увлажненную ткань или салфетку для удаления трудных загрязнений.
Защита окружающей среды
Если вы видите этот символ на продукте, не выбрасывайте его с промышленными
или пищевыми отходами. В некоторых регионах созданы системы для сбора и
утилизации электронного оборудования. Свяжитесь с местными органами власти
для получения информации об утилизации для вашего региона.
Авторские права и ограничение ответственности
Все права защищены. Никакая часть данной публикации не может быть воспроизведена в любой
форме и любыми средствами, переведена на другой язык, переписана, переделана в любой другой
форме, храниться в поисковой системе или передаваться любыми средствами, включая
электронные или механические.
Запрещена запись или ксерокопирование без предварительного письменного разрешения
владельца.
Внимание!
В связи с постоянным проведением модернизаций и улучшения функциональности
оборудования, внешний вид, технические характеристики и функциональность
могут быть изменены без предварительного уведомления.
Данное руководство пользователя может содержать неточности или опечатки.
Производитель оставляет за собой право вносить изменения к информации,
содержащейся в данном руководстве, а также к комплектации и/или общему
описанию изделия.
SL-07N Cloud
35 REV. 2.0 36
!
7”, IPS
1024×600
PAL/NTSC/AHD, TVI, CVI (720p,1080p)
70
MicroSD, 256
4
8
, ~100-240
176×133×20
10 ... +55 ˚C
SL-07N Cloud
37 38
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
. ;
. ;
. ;
;
«» – ,
, ;
«» – ,
, ;
( );
«»:
• , ;
• , ,
;
• ,
// ;
«» –
;
«» – ;
«» – ;
«» – ;
microSD ( );
«» – / ;
.
165 мм
230 мм 22
мм
1.
SL-07N Cloud − 1 .
Wi-Fi − 1 .
− 1 .
− 1 .
− 1 .
− 1 .
2.
5
1 2 3 4
6
7
8
9
10
11
12
13
14
15
3.
/