Quick Installation Guide
9-Port 10/100M Ethernet Desktop Switch
8FE+1GE Desktop Switch
TEF1109D/TEF1109DT
Package contents
· Switch * 1
· Power adapter * 1
· Quick installation guide * 1
Connect your devices
Power
LAN1 LAN2 LAN3 LAN4 WAN
VLAN
on
Grounding terminal
Internet
Router
IP camera
Computer
Printer
Port 9
LAN port WAN port
Tip:
All ports of your switch support the auto MDI/MDIX function, indicating that either straight cable or crossover cable is acceptable
to connect your switch to Ethernet devices.
To protect your switch from lightning damage, connect the grounding terminal of the switch to a grounding cable.
IEEE 802.3, IEEE 802.3u,
IEEE 802.3x
IEEE 802.3, IEEE 802.3u,
IEEE 802.3x,
IEEE 802.3ab
10/100/1000 Mbps RJ45 Port
Auto learning & auto aging
140.2 mm * 66.2 mm * 25.2 mm
Input: 100-240 V AC, 50/60 Hz, 0.3 A
Output: 9 V DC, 0.6 A
Temperature: (0 - 40) °C
Humidity: (10 - 90) % RH, non-condensing
Temperature: (-40 - 70) °C
Humidity: (5 - 90) % RH, non-condensing
Ethernet: 10 Mbps (half duplex) / 20 Mbps
(full duplex)
Fast Ethernet: 100 Mbps (half duplex) / 200
Mbps (full duplex)
Gigabit Ethernet:
2000 Mbps (full
duplex)
Ethernet: CAT3 UTP/STP cable or better
Fast Ethernet: CAT5 UTP/STP cable or better
Gigabit Ethernet: CAT5e
or CAT6 UTP/STP cable
(recommended)
Specifications
The switch is connected to a
power resource properly.
The switch is disconnected or not
properly connected to a power
resource.
The port is connected properly.
Data is being transmitted over the
port.
The port is disconnected or
improperly connected.
LED indicators
Working mode introduction
The switch has two modes: VLAN off and VLAN on. Use the
slide switch to set the switch to your required mode
according to the following descriptions.
VLAN off: Default mode of the switch. In this mode, all ports
can communicate with each other.
VLAN on: In this mode, ports 1 to 8 of TEF1109D/TEF1109DT
can communicate with port 9 but cannot communicate with
each other. You can enable this mode to reduce broadcast
storm and isolate DHCP broadcast.
English
Das Gerät ist korrekt an eine
Stromversorgung angeschlossen.
Der Switch ist von der
Stromversorgung getrennt oder nicht
ordnungsgemäß angeschlossen.
Der Port ist korrekt verbunden.
Die Daten werden über den Port
übertragen.
Der Port ist nicht verbunden oder
falsch angeschlossen.
LED-Anzeige
Einführung in die Betriebsmodi
Der Switch hat zwei Modi: VLAN off und VLAN on. Schalten
Sie den Switch über den Schieberegler in den gewünschten
Modus. Wählen Sie den Modus gemäß der nachfolgenden
Beschreibungen aus.
VLAN off: Ist der Standardmodus des Switches. In diesem
Modus können alle Ports des Switches untereinander
kommunizieren.
VLAN on: In diesem Modus können die Ports 1 bis 8 des
TEF1109D/TEF1109DT mit dem Port 9 kommunizieren aber
nicht untereinander. Verwenden Sie diesen Modus, um
Broadcast-Storm zu reduzieren oder den DHCP-Broadcast
zu isolieren.
Deutsch
Le dispositif est branché
correctement à l'alimentation.
Le commutateur est déconnecté de la
source d’alimentation ou n’est pas
connecté à une source d’alimentation.
Le port est correctement connecté.
Les données sont transmises à travers
le port.
Le port est déconnecté ou n’est pas
correctement connecté.
Indicateurs LED
Introduction du mode de
fonctionnement
Le commutateur a deux modes: VLAN off, et VLAN on.
Utilisez la glissière pour régler le commutateur au mode
requis selon les descriptions suivantes.
VLAN off: Mode par défaut du commutateur. Dans ce mode,
tous les ports du commutateur pourraient communiquer
entre eux.
VLAN on: Dans ce mode, les ports 1 à 8 de
TEF1109D/TEF1109DT peuvent communiquer avec le port9
mais pas entre eux. Vous pouvez activer ce mode pour
réduire la diffusion et isoler la diffusion DHCP.
Français
El dispositivo está conectado a la
fuente de alimentación
correctamente.
El switch está desconectado o no
correctamente conectado a una
fuente de alimentación.
El puerto está conectado
correctamente.
Se están transmitiendo datos sobre el
puerto.
El puerto está desconectado o mal
conectado.
Indicadores LED
Introducción al Modo Trabajo
El switch dispone de dos modos: VLAN off y VLAN on. Use el
interruptor para establecer el switch en el modo requerido
de acuerdo con las descripciones siguientes.
VLAN off: modo predeterminado del switch. En este modo,
todos los puertos del conmutador pueden comunicarse
entre sí.
VLAN on: En este modo, los puertos 1 a 8 del
TEF1109D/TEF1109DT pueden comunicarse con el puerto 9
pero no pueden comunicarse entre sí. Puede usar este
modo para reducir la tormenta de difusión y aislar la
transmisión DHCP.
Español
O dispositivo está ligado à fonte de
alimentação adequada.
O interruptor é desligado da fonte de
alimentação ou não é conectado a
uma fonte de alimentação.
A porta está ligada corretamente.
Os dados estão a ser transmitidos
pela porta.
A porta está desconectada ou
indevidamente conectada.
Indicadores LED
Introdução ao Modo de Trabalho
O interruptor tem dois modos: VLAN off e VLAN on. Use o
controlo deslizante para definir o interruptor para o modo
necessário de acordo com as seguintes descrições.
VLAN off: Modo padrão do interruptor. Neste modo, todas
as portas do switch podem se comunicar entre si.
VLAN on: Neste modo, as portas 1 a 8 do
TEF1109D/TEF1109DT podem comunicar com a porta 9 mas
não podem comunicar entre si. Pode utilizar este modo para
reduzir os distúrbios de transmissão e isolar a transmissão
DHCP.
Português
Il dispositivo è collegato alla rete
elettrica correttamente.
L'interruttore è scollegato
dall'alimentazione o non
correttamente collegato a una presa
di corrente.
La porta è collegata correttamente.
I dati vengono trasmessi attraverso
la porta.
La porta è scollegata o collegata in
modo non corretto.
Indicatori LED
Introduzione modalità di lavoro
Lo switch presenta due modalità: VLAN off, e VLAN on.
Utilizzare l'interruttore scorrevole per regolare l'interruttore
nella modalità richiesta secondo le seguenti indicazioni.
VLAN off: Modalità predefinita dell'interruttore. In questa
modalità tutte le porte dello switch possono comunicare tra
loro.
VLAN on: In questa modalità, le porte 1 - 8 del
TEF1109D/TEF1109DT possono comunicare con la porta 9
ma non tra di loro. Si può utilizzare questa modalità per
ridurre il broadcast storm e isolare la trasmissione DHCP.
Italiano
A készülék helyesen van az
energiaellátáshoz csatlakoztatva.
A váltó nincs, vagy nem
megfelelően van csatlakoztatva a
tápegységhez.
Az egyező port helyesen van
csatlakoztatva.
Adatátvitel van folyamatban a
porton keresztül.
A port nincs, vagy nem
megfelelően van csatlakoztatva.
LED-jelzők
Bevezetés: üzemmódok
A kapcsoló két üzemmóddal rendelkezik: VLAN off (VLAN
kikapcsolva) és VLAN on (VLAN bekapcsolva). A
csúszókapcsolóval állítsa a kapcsolót a kívánt üzemmódba
az alábbi leírások szerint.
VLAN off: A kapcsoló alapértelmezett üzemmódja. Ebben a
módban a váltó összes portja tud kommunikálni egymással.
VLAN on: Ebben az üzemmódban a TEF1109D/TEF1109DT
1–8-es portja képes kommunikálni az 9-ös porttal, de nem
képesek kommunikálni egymással. Ezzel az üzemmóddal
csökkentheti a szórási viharokat, és elkülönítheti a
DHCP-szórást.
Magyar
Превключвателятесвързан
правилноселектрозахранването.
Прекъсвачътеизключенот
захранванетоилинеесвързан
правилноснего.
Портътесвързанправилно.
Даннитесепредаватпрезпорта.
Портътепрекъснатили
неправилносвързан.
LED индикатори
Въведениевработниярежим
Превключвателятимадварежима:VLANoff(VLAN
изключено)иVLANon(VLANвключено).Използвайте
страничнияпревключвател,заданастроите
превключвателявизискваниярежимспоредследните
описания.
VLANoff:Режимпоподразбираненапревключвателя.
Втозирежимвсичкипортовемогатдакомуникират
единсдруг.
VLANon:Втозирежимпортовеот1до8от
TEF1109D/TEF1109DTмогатдакомуникиратспорт9,но
немогатдакомуникиратединсдруг.Можетеда
използватетозирежим,заданамалитебродкаст
бурятаидаизолиратеизлъчванетонаDHCP.
Български
Urządzenie jest prawidłowo
podłączone do źródła zasilania.
Urządzenie jest odłączone od źródła
zasilania lub nie zostało do niego
poprawnie podłączone.
Gniazdo jest połączone poprawnie.
Port obsługuje przesyłanie danych.
Port jest odłączony lub niepoprawnie
podłączony.
Kontrolki LED
Wprowadzenie do trybów pracy
Switch może działać w dwóch trybach: VLAN off. i VLAN on.
Za pomocą przełącznika włącz w switchu wymagany tryb
pracy. Opisy trybów znajdują się poniżej.
VLAN off: Tryb domyślny switcha. W tym trybie wszystkie
porty switcha mogą się ze sobą komunikować.
VLAN on: W tym trybie porty od 1 do 8 urządzenia
TEF1109D/TEF1109DT mogą komunikować się z portem 9,
ale nie ze sobą nawzajem. Dzięki temu trybowi można
zmniejszyć liczbę burz broadcastowych i odizolować
rozgłaszanie DHCP.
Polski
Dispozitivul este conectat corect la
sursa de alimentare.
Switch-ul este deconectat de la sursa
de alimentare sau nu este conectat
corect la sursa de alimentare.
Portul corespunzător este conectat
corect.
Datele sunt transmise prin port.
Portul este deconectat sau nu este
conectat corect.
Indicatoare LED
Prezentarea modurilor de lucru
Switch-ul are două moduri: VLAN off şi VLAN on. Setati
switch-ul în modul dorit din comutator, conform
următoarelor descrieri.
VLAN off: Modul implicit al switch-ului. În acest mod, toate
porturile pot comunica între ele.
VLAN on: În acest mod, porturile 1 - 8 ale
TEF1109D/TEF1109DT pot comunica cu portul 9 dar nu pot
comunica între ele. Puteți utiliza acest mod pentru a reduce
broadcast storm și pentru a izola DHCP broadcast.
Română
Коммутаторподключенк
источникупитания.
Коммутаторотключенот
источникапитанияили
подключенкнемунеправильно.
Портподключенправильно.
Черезпортосуществляется
передачаданных.
Портнеподключенилиподключн
неправильно.
Светодиодныеиндикаторы
Обзоррежимовработы
Укоммутатораестьдварежима:VLANoffиVLAN
on.Используйтепереключательдляперевода
коммутаторавнужныйрежим,выбранныйна
основеописания.
VLANoff:Режимкоммутаторапоумолчанию.В
этомрежимевсепортымогутподключатьсядругк
другуиимеютодинаковыйприоритет.
VLANon:Вэтомрежимепорты1‒8устройства
TEF1109D/TEF1109DTмогутподключатьсяк
порту9,нонемогутподключатьсядругкдругу.В
этотрежимможноперейти,чтобыуменьшить
broadcastштормиизолироватьDHCPbroadcast.
Русский
Горит
постоянно
Горит
постоянно
FCC Statement
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules.These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment.This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
This device complies with Part 15 of the FCC Rules.Operation is
subject to the following two conditions:(1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Caution!
Anychanges or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. (2) To avoid unnecessary radiation interference, it is
recommended to use a shielded RJ45 cable.
Caution:
Adapter Model: BN049-A05009E/BN049-A05009B
Manufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.
Input: 100 - 240 V AC 50/60 Hz, 0.3 A
Output: 9 V 600 mA
: DC Voltage
NOMBRE DEL PRODUCTO:
Switch de escritorio 8FE+1GE
MODELO: TEF1109DT
Alimentador de Energía:
Alimentación: 100-240 V ca 50/60 Hz, 0.3 A
Salida: 9 V cc 0.6 A
CE Mark Warning
This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
The mains plug is used as disconnect device; the disconnect device
shall remain readily operable.
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this
equipment. (2) To avoid unnecessary radiation interference, it is
recommended to use a shielded RJ45 cable.
This product bears the selective sorting symbol for Waste electrical
and electronic equipment (WEEE). This means that this product must
be handled pursuant to European directive 2012/19/EU in order to
be recycled or dismantled to minimize its impact on the
environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when he buys a new electrical or
electronic equipment.
RECYCLING
LA OPERACIóN DE ESTE DISPOSITIVO ESTA SUJETA A LAS
SIGUIENTES CONDICIONES:
a) Es posible que este equipo o dispositivo no cause
interferencia perjudicial.
b) Este equipo o dispositivo debe aceptar cualquier tipo de
interferencia, incluyendo la que pueda causar su operación no
deseada.
NOMBRE DEL PRODUCTO:
Switch de escritorio Ethernet de 9 puertos 10 / 100M
MODELO: TEF1109D
Alimentador de Energía:
Alimentación: 100-240 V ca 50/60 Hz, 0.3 A
Salida: 9 V cc 0.6 A
Copyright
Copyright © 2018 Shenzhen Tenda Technology Co., Ltd. All rights
reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda
Technology Co., Ltd. Other brand and product names mentioned
herein are trademarks or registered trademarks of their respective
holders. Specifications are subject to change without notice.
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan
District, Shenzhen, China. 518052
Canada hotline: 1-888-998-8966
Hong Kong hotline: 00852-81931998
Website: http://www.tendacn.com
If any item is missing, damaged or incorrect, please keep the
original packaging and contact the local reseller or distributor
immediately.
Example: TEF1109D
