English
E-1
Read this before using the speakers.
●
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
●
Install the speakers in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the speakers to rain or water.
● To prevent the enclosure from warping or discoloring, do
not place the speakers where they will be exposed to
direct sunlight or excessive humidity.
● Do not place the following objects on the speakers:
Glass, china, etc.
If glass etc. falls by vibrations and breaks, it may cause
personal injury.
A burning candle etc.
If the candle falls by vibrations, it may cause fire and
personal injury.
A vessel with water in it
If the vessel falls by vibrations and water spills, it may
cause damage to the speakers, and/or you may get an
electric shock.
● Do not place the speakers where foreign objects such as
water drips might fall. It might cause a fire, damage to
the speakers, and/or personal injury.
● Do not place the speakers where they are liable to be
knocked over or struck by falling objects. Stable
placement will also ensure better sound performance.
PRECAUTIONS
Thank you for selecting this YAMAHA NS-6HX speaker system.
● Placing the speakers on the same shelf or rack as the
turntable can result in feedback.
● Never put a hand or a foreign object into the port located
on the front of the speaker as this might cause personal
injury and/or damage to the speaker.
● When moving the speaker, do not hold the port as it
might cause personal injury and/or damage to the
speaker.
● Any time you note distortion, reduce the volume control
on your amplifier to a lower setting. Never allow your
amplifier to be driven into “clipping”. Otherwise the
speakers may be damaged.
●
When using an amplifier with a rated output power higher
than the nominal input power of the speakers, care should
be taken never to exceed the speakers’ maximum input.
●
Do not attempt to clean the speakers with chemical solvents
as this might damage the finish. Use a clean, dry cloth.
● Do not attempt to modify or fix the speakers. Contact
qualified YAMAHA service personnel when any service
is needed. The cabinet should never be opened for any
reasons.
● Secure placement or installation is the owner’s
responsibility.
YAMAHA shall not be liable for any accident caused
by improper placement or installation of speakers.
The speaker is constructed with the majority of the weight
located in its upper portion, and is thus susceptible to falling
over if proper care is not taken to insure its stability. If the
speaker falls over, it may damage the speaker or be the
cause of injury (or even death) to persons and/or damage to
personal property.
PRECAUTIONS WHEN POSITIONING
For safe and proper use of the speaker:
• Position the speaker in a location that is solid, level,
smooth, and low (with respect to the floor).
• Do not push or apply pressure to the side of the speaker
when moving, or lean objects against the side of the
speaker.
• Do not sit on or set objects on top of the speaker.
• Do not remove the stands attached to the bottom of the
speaker as this might cause the serious accidents,
resulting from falling over of the speaker.
Vibrations or jolts associated with earthquakes and other
phenomena or activities may cause the speaker to fall over.
For safety reasons, using commercially available products
that increase stability in the speaker is recommended
(metal fittings or chains, etc.).
NS-6HX
Speaker System
OWNER’S MANUAL
G R
E-2
ATTACHING THE SPIKES
When setting up the speakers on a thick carpet, use the
spikes to increase stability and improve sound quality.
Attach the spikes at four points on the speaker properly by
following the procedure below.
Procedure:
1
Turn the nut close to the tip of the spike.
2
Screw the spikes into the hole of the stands.
3
Place the speaker in the desired location in an upright
position and adjust the length of the spike to match the
depth of the carpet.
4
When adjustment is finished, turn the nut up to the base
of the stand firmly.
Notes
●
The tips of the spikes may scratch or otherwise
damage the flooring. Please be careful when
positioning the speakers.
●
If force is applied to the side of the speaker, it may fall
and damage the speaker or cause personal injury.
Please be careful.
Nut x 4
Spike x 4
PLACING THE SPEAKERS
■ Using as 2ch stereo speakers
Better stereo images will be obtained when the speakers
are slightly angled in towards the listeners.
■ Using as main speakers in a multi channel
system
Position the speakers on both sides of the TV. The
positioning of speakers is important, because it controls the
whole sound quality of a multi channel system. Set up the
speakers on the basis of your listening position by following
the owner’s manual supplied with your amplifier.
Note
These speakers feature a magnetically shielded design,
but there is still a chance that placing them too close to
a TV set might impair picture color. Should this happen,
move the speakers away from the TV set.
Effect L
Effect R
Subwoofer
Center
NS-6HX
NS-6HX
1
2
English
E-3
SPEAKERS
A
B
L
R
+
+
–
–
+
–
CONNECTIONS TO YOUR AMPLIFIER
Amplifier or
Receiver
Tighten
NS-6HX (L)
This speaker system is capable of standard connections and bi-wired connections. Before making
connections, make sure that the amplifier is switched off.
■ CONNECTIONS
• Connect the screw-type input terminals at the rear of the
speakers to the speaker output terminals of the amplifier
(or receiver) with the speaker cable.
• Connect the (+) terminals on the amplifier (or receiver)
and the speakers using one side of the cable. Connect
the (–) terminals on both components using the other
side of the cable.
• Connect one speaker to the left (marked L) terminals of
your amplifier, and another speaker to the right (marked
R) terminals, making sure not to reverse the polarity
(+, –). If one speaker is connected with reversed polarity,
the sound will be unnatural and lack bass.
How to connect:
1 Loosen the knob.
2 Insert the bare wire. [Remove the insulation coating at
the extremity of each speaker cable by twisting the
coating off.]
3 Tighten the knob and secure the cable.
Test the firmness of the connection by pulling lightly on
the cable at the terminal.
Note
Do not let the bare speaker wires touch each other as
this could damage the speaker or the amplifier, or both
of them.
Loosen
<Standard connections>
Short bar
Leave the short
bars in place when
connecting.
NS-6HX (R)
Speakers output
terminals of the
amplifier (or
receiver)
E-4
+ ––
SPEAKERS
L
R
SPEAKERS
A
B
L
R
++ ––
+
+
–
When using a banana plug
<General model only>
1 Remove the cover by pulling it toward you.
2 Tighten the terminal knob.
3 Simply insert the banana plug into the terminal.
Bi-Wired Connections
This speaker system is capable of bi-wired
connections. To connect the speaker to the output
terminals of the amplifier (or receiver), two pairs
of cables for each of woofer and tweeter/mid-
range are used instead of standard connections.
This type of connection decreases the modulation
distortion caused by electric resistance of the
cables and driving current of the speakers.
Consequently, purer sound quality can be
expected.
To utilize bi-wired connections, remove the short
bars from the terminals first, and then connect the
woofer and tweeter/mid-range to the amplifier
separately using two pairs of cables.
<Bi-wired connections>
Remove the short
bars before
connecting.
Amplifier or
Receiver
Woofer terminals
Tweeter/Mid-range
terminals
Banana plug
2
1
3
Amplifier or
Receiver
NS-6HX (L)NS-6HX (R) NS-6HX (L)NS-6HX (R)
Both SPEAKERS A and B
should be selected.
English
E-5
SPECIFICATIONS
Type .......................................3-way 3-speaker bass reflex
speaker system
Magnetic shielding type
Driver ............................................ 20 cm (8”) cone woofer
Wave guide horn 13 cm (5”) cone mid-range
Wave guide horn 3 cm (1”) dome tweeter
Impedance ................................................................... 6 Ω
Frequency Response ................................45 Hz to 50 kHz
Nominal Input Power ................................................ 100 W
Maximum Input Power.............................................. 300 W
Sensitivity ...................................................91 dB/2.83 V/m
Crossover Frequency ...................................600 Hz, 4 kHz
Dimensions (WxHxD) .......................364 x 1062 x 397 mm
(14-5/16” x 41-13/16” x 15-5/8”)
Weight ............................................ 29.0 kg (63 lbs. 15 oz.)
Accessories ......................................................... Spike x 4
Nut x 4
● Specifications subject to change without notice due to
product improvements.
● Care should be taken not to exceed the input power
values noted above.
ATTACHING THE FRONT COVER
The speaker and the front cover are packed separately.
To attach the cover, line up the six pegs on the speaker
with the six corresponding holes on the inside surface of
the cover and push gently.
To remove the cover, hold on to both sides and slowly pull
straight away from the speaker.
Note
When the cover is removed, take care not to touch the
speaker units with your hands or to exert excessive
force with tools.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
V819270
Printed in Indonesia
/