Yamaha HY144 Руководство пользователя

Бренд: Yamaha

Модель: HY144

Тип: Руководство пользователя

Yamaha HY144 — это универсальная карта расширения, предлагающая широкий спектр возможностей для работы с аудио.

HY144-D-SRC Firmware Update Guide 1

■ Precautions

・ The user assumes full responsibility for the update.

・ Update the firmware components one device at a time.

・ Please note that the device may be damaged if you fail to follow these instructions

properly, or turn off the device or disconnect the cable while the update is in

progress.

・ If the update fails, and the device still does not operate correctly even after you

execute the update once again, please contact your Yamaha dealer.

・ This guide is the exclusive copyrights of Yamaha Corporation.

・ Audinate owns exclusive copyrights for the Dante firmware and its update program.

・ It is prohibited to duplicate or modify the firmware, software or this guide, in part or

in their entirety, without permission from the copyright owner.

・ The illustrations and screens as shown in this guide are for instructional purposes

only.

・ Yamaha Corporation makes no representations or warranties with regard to the use

of the software and documentation and cannot be held responsible for the results

of the use of this guide and the software.

・ Windows is a registered trademark of Microsoft ® Corporation in the United States

and other countries.

・ Mac is trademark of Apple Inc., registered in the U.S. and other countries.

・ The company names and product names in this guide are the trademarks or

registered trademarks of their respective companies.

・ Software may be revised and updated without prior notice.

■ Contents

Preparing for the update

.................................................... 2

Update procedure sequence ........................................... 2

Install the Dante Firmware Update Manager .................. 3

Computer TCP/IP setting ................................................. 4

Updating the firmware ..................................................... 6

About Failsafe Mode ....................................................... 10

Trouble shooting ............................................................ 14

SRC mode ........................................................................ 15

HY144-D-SRC Firmware Update Guide

Thank you for choosing a Yamaha product. This guide explains how to update the HY144-D-SRC

firmware. The SRC modes can be changed by updating to the card’s firmware corresponding to each

SRC mode (page 7).

HY144-D-SRC Firmware Update Guide 2

Preparing for the update

In order to update, you will need to prepare the

following items.

• A Windows or a Mac computer

For the system requirements, refer to the

Yamaha Pro Audio website.

https://www.yamaha.com/proaudio/

• An Ethernet cable

CAT5e or higher recommended. Straight or

cross.

• The HY144-D-SRC firmware update

program

Download the latest program from the

following URL.

https://www.yamaha.com/proaudio/

Update procedure

sequence

Update each firmware component in the

following sequence.

To update more than one HY144-D-SRC,

configure “Computer TCP/IP setting” and

perform “Updating the firmware” one by one.

Install the Dante Firmware Update Manager

↓

Computer TCP/IP setting

↓

Updating the firmware

NOTE

For details of the Dante Firmware Update Manager, refer to

“AUD-MAN-Firmware_Update_Manager-vx.x.pdf" (x.x represents

the version number) stored in the compressed file folder.

HY144-D-SRC Firmware Update Guide 3

Before you update the firmware, you must install

the Dante Firmware Update Manager.

Double-click the Dante Firmware Update

Manager installer downloaded in “

Preparing for

the update

” (Windows:

DanteFirmwareUpdateManager-x.x.x.exe,

Mac: DanteFirmwareUpdateManager-x.x.x.dmg)

and follow the on-screen instructions to install

the firmware.

x.x.x represents the version number of the Dante

Firmware Update Manager.

In addition, extract the Dante firmware

(extension: .dnt) from the compressed file.

Only alphanumeric characters, “-” (hyphen), and

“_”(underscore) can be used in the path to save

the Dante firmware. If the path contains other

characters, Dante Firmware Update Manager will

not work properly. You must save the Dante

firmware in a directory whose name contains

only alphanumeric characters, “-” (hyphen), or

“_” (underscore) (e.g., C:\temp).

NOTE

• The “Windows Security” dialog box may appear. In such case,

click [Install this driver software anyway].

• You may be prompted to restart the computer after the

installation is complete. Before proceeding to update, restart

the computer.

• When installing the Dante Firmware Update Manager,

temporarily disable any running anti-virus software.

Install the Dante Firmware Update Manager

HY144-D-SRC Firmware Update Guide 4

To update Dante firmware, configure computer

TCP/IP settings.

Windows

1. Open the “Network and Sharing Center”

as described below.

Windows 7

Select [Start] → [Control Panel], then click or

double-click [Network and Sharing Center]

or [View network status and tasks].

Windows 8.1 and Windows 10

Right-click [Start] → [Control Panel], then

click or double-click [Network and Sharing

Center] or [View network status and tasks].

The “Network and Sharing Center” is

displayed.

2. Click [Manage network connection] or

[Change Adapter settings] from the

“Tasks” list located in the left side of

“Network and Sharing Center” window,

then double-click [Local Area

Connection].

The “Local Area Connection Status” dialog

box will be displayed.

NOTE

• The “User Account Control” dialog box may appear. Click

[Continue] or [Yes].

• If the “Local Area Connection properties” dialog box

appears, skip ahead to step 4.

3. Click [Properties].

The “Local Area Connection properties”

dialog box will be displayed.

Computer TCP/IP setting

HY144-D-SRC Firmware Update Guide 5

NOTE

The “User Account Control” dialog box may appear. Click

[Continue] or [Yes].

4. Select [Internet Protocol Version 4

(TCP/IPv4)], then click [Properties].

The “Internet Protocol Version 4(TCP/IPv4)

Properties” dialog box will be displayed.

5. Click [Obtain an IP address

automatically].

6. Click [OK].

Mac

1. Click [System Preferences] → [Network].

The “Network” dialog box will be displayed.

2. Click the service that you want to connect

to the device.

If you're using the Ethernet port that's built

into the Mac, click [Ethernet].

3. In “Configure IPv4,” choose [Using

DHCP].

4. Click [Apply] button, then close

“Network” dialog box.

HY144-D-SRC Firmware Update Guide 6

Described below are the procedures to update

the Dante module firmware integrated in the

HY144-D-SRC.

NOTE

Perform the update with the HY144-D-SRC installed in the slot of

a compatible device.

1. Connect the Dante [PRIMARY] connector

of the HY144-D-SRC to the Ethernet

connector on the computer using an

Ethernet cable.

Be sure to directly connect the computer

and the HY144-D-SRC, and do not connect

any other Dante device to the computer.

2. Turn on the power to the device to which

the HY144-D-SRC is installed.

3. Windows: Select [Start]→[All programs]

or [All apps]→[Audinate]→[Dante

Firmware Update Manager]→[Dante

Firmware Update Manager] , then right-

click and select [Run as Administrator].

Mac: [Application]→[Dante Firmware

Update Manager], then double-click

“Dante Firmware Update Manager.”

The Dante Firmware Update Manager will

start up. Check that the version number is

3.10.4.6 or higher from the title bar.

NOTE

The “User Account Control” dialog box may appear. Click

[Continue] or [Yes].

Updating the firmware

HY144-D-SRC Firmware Update Guide 7

4. If you see the interface selection screen,

select the interface card to connect the

Dante device.

5. Click [Update Dante Firmware].

6. Click [Browse] and select

“FWUpdate_HY144-D-SRC

_mode_vxxx_swyyy.dnt,” then click

[Open].

mode represents the SRC mode name, xxx

and yyy represent the firmware version

number.

NOTE

Only alphanumeric characters, “-” (hyphen), and

“_”(underscore) can be used in the path to save the Dante

firmware. If the path contains other characters, Dante

Firmware Update Manager will not work properly. You must

save the Dante firmware in a directory whose name

contains only alphanumeric characters, “-” (hyphen), or “_”

(underscore) (e.g., C:\temp).

NOTE

The SRC modes can be changed by updating to the card’s

firmware corresponding to each SRC mode.



144io mode

FWUpdate_HY144-D-SRC_144io_vxxx_swyyy.dnt



144io Sync SRC mode

FWUpdate_HY144-D-SRC_144ioSyncSRC_vxxx_swyyy.dnt



72io Async SRC mode

FWUpdate_HY144-D-SRC_72ioAsyncSRC_vxxx_swyyy.dnt



144i Async SRC mode

FWUpdate_HY144-D-SRC_144iAsyncSRC_vxxx_swyyy.dnt



144o Async SRC mode

FWUpdate_HY144-D-SRC_144oAsyncSRC_vxxx_swyyy.dnt

For details on each of the SRC modes, refer to the “SRC

mode.”

7. Click [Next].

NOTE

In some cases the Windows firewall may be blocking the

Dante Firmware Update Manager. Select the [Private

network] check box, and click [Allow access]. Alternatively,

in the Windows firewall, click [Allow programs or functions

through the Windows firewall], and if the “fum” checkbox is

HY144-D-SRC Firmware Update Guide 8

unselected, select this check box to allow access.

If the update manager is blocked by the Windows firewall,

the “Upgrade failed.” dialog box appears.

8. Check the HY144-D-SRC to update.

Check the version of the update files and the

version number indicated in the HY144-D-

SRC line.

NOTE

If the HY144-D-SRC is not indicated, click [Refresh]. If it is

still not indicated, check whether the cable might be

disconnected or broken, whether the TCP/IP settings are

correct or not, whether the device to which the HY144-D-

SRC is installed is running or not, and whether the HY144-D-

SRC is recognized by the Dante Controller.

9. Click [Start].

The update operation will begin.

“Updating(n/m)” appears in the Status field

during updating. “Done” is displayed once

update is completed.

NOTICE

Update takes 2 to 4 minutes. During the update operation,

do not turn off the power to the device or disconnect the

cable. If update fails due to disconnection of the power

cable during the update, or due to other reasons, the device

may become inoperative.

NOTE

If the update is not completed after 5 minutes, or an update

failure indication appears, click X at the upper right corner

of Dante Firmware Update Manager to exit the program

without turning off the power of the device to which the

HY144-D-SRC Firmware Update Guide 9

HY144-D-SRC is installed, and restart the procedure from

the step 3. If update still fails, follow the instructions stated

in “About Failsafe Mode” to perform the recovery process.

10. Turn off the power to the device to which

the HY144-D-SRC is installed, and then on

again.

NOTE

Rapidly turning the unit on and off in succession can cause

it to malfunction. After turning the unit off, wait for at least

few seconds before turning it on again. Refer to the owner’s

manual supplied with each device for how much time

should elapse between turning the power off and on again.

11. Windows: Select [Start]→[All programs]

or [All apps]→[Audinate]→[Dante

Controller]→[Dante Controller] , then

right-click and select [Run as

Administrator].

Mac: [Application]→[Dante Controller],

then double-click “Dante Controller.”

The Dante Controller will start up.

NOTE

The “User Account Control” dialog box may appear. Click

[Continue] or [Yes].

12. Perform the “Clear Config” operation to

initialize the HY144-D-SRC.

NOTE

When you change the SRC mode, the settings before the

mode change may still be present and the device may not

work properly. To prevent this problem, take a note of the

Dante settings in advance, initialize all the Dante settings

using “Clear Config,” and then set them again manually.

For details on instruction, refer to the Dante

Controller User Guide available on the

following website:

https://www.yamaha.com/proaudio/

The firmware update is now complete.

HY144-D-SRC Firmware Update Guide 10

The Dante module integrated in the HY144-D-

SRC may become unusable due to data

corruption if the Dante device is powered-off

during a firmware update.

To recover from such a state, the Dante module

will enter “failsafe mode.”

To restore the Dante module from failsafe mode,

a recovery image must be sent from the Dante

Firmware Update Manager.

If the red ERROR indicator of the HY144-D-SRC is

lit, it may be that the Dante module is in failsafe

mode.

Use Dante Controller to check whether the

Dante module is in failsafe mode.

A Dante module that is in failsafe mode is shown

as a red device name in the network grid view of

Dante Controller (version 3.1.x or later).

About Failsafe Mode

HY144-D-SRC Firmware Update Guide 11

Described below are the procedures to recover

the Dante module integrated in the HY144-D-

SRC.

1. Turn off the power to the device to which

the HY144-D-SRC is installed.

2. Separate the HY144-D-SRC from the

Dante network.

3. Connect the Dante [PRIMARY] connector

of the HY144-D-SRC to the Ethernet

connector on the computer using an

Ethernet cable.

In some cases, an error may occur during

recovery if you are going through a network

switch. Connect the computer with the

HY144-D-SRC in a one-to-one connection.

4. Turn on the power to the device to which

the HY144-D-SRC is installed.

5. Disable all but one of the network

interfaces on your computer.

You should also disable the wireless LAN.

6. Windows: Select [Start]→[All programs]

or [All apps]→[Audinate]→[Dante

Firmware Update Manager]→[Dante

Firmware Update Manager ] , then right-

click and select [Run as Administrator].

Mac: [Application]→[Dante Firmware

Update Manager], then double-click

“Dante Firmware Update Manager.”

The Dante Firmware Update Manager will

start up.

NOTE

The “User Account Control” dialog box may appear. Click

[Continue] or [Yes].

HY144-D-SRC Firmware Update Guide 12

7. If you see the interface selection screen,

select the interface card to connect the

Dante device.

8. Click [Failsafe Recovery].

9. When the HY144-D-SRC is detected, click

the [Stop Scan] button.

If several minutes have passed without

detection, check whether the cable might be

disconnected or broken, whether the TCP/IP

settings are correct or not, whether the

device to which the HY144-D-SRC is installed

is running or not, and whether the HY144-D-

SRC is recognized by the Dante Controller.

10. Select the check box of the detected

HY144-D-SRC.

HY144-D-SRC Firmware Update Guide 13

11. Click [Start].

A pop-up is displayed confirming that you

wish to proceed.

12. Click [OK] to start the recovery.

Dante Firmware Update Manager will display

“Processing Safe Recovery,” and then “Safe

Recovery Done.” when the device(s) are

recovered.

13. Exit the Dante Firmware Update Manager,

and wait for two minutes before turning

off the power to the device to which the

HY144-D-SRC is installed.

After recovery, the Dante module will be

restarted. If you power-off the device to

which the HY144-D-SRC is installed before

restart is completed, the data of the Dante

module will be corrupted, and you will have

to perform the recovery once again. Start

Dante Controller, and if the device name is

shown in black, it is safe to turn off the

power.

14. The correct Dante firmware now needs to

be loaded.

After recovery, the Dante firmware will not

be the latest version. To update to the latest

firmware, perform steps 2 through 10 of

“Updating the firmware.”

The recovery and the firmware update are now

complete.

HY144-D-SRC Firmware Update Guide 14

Trouble shooting

• Is the Ethernet cable broken?

Replace with an Ethernet cable which can

communicate properly.

• Are the network settings configured

correctly?

Check your computer settings (page 4).

• Is there any resident security software

installed?

If the firewall function of anti-virus or security

software is enabled, the communication may

not be established properly.

• Is the HY144-D-SRC to be updated is locked

by Dante Device Lock?

Unlock the Dante Device Lock function of the

HY144-D-SRC using Dante Controller.

HY144-D-SRC Firmware Update Guide 15

SRC mode

The HY144-D-SRC has five SRC modes and they can be changed according to your sound system.

Data length and number of inputs/outputs are limited by the selected SRC mode.

You can confirm the SRC mode in use from Dante Controller “Device Information” or SLOT settings on

the touch screen of the control surface.

Synchronous SRC: When the word clock ratio of the Dante network to the host device is synchronized at 1:2 (48 kHz:96 kHz or 44.1

kHz:88.2 kHz), data with different sampling frequencies can be transmitted without reducing the number of input and output channels.

When the Dante network sampling frequency is 44.1 kHz, frequency characteristics above 18 kHz slightly deteriorate to eliminate aliasing

noise.

Asynchronous SRC: Dante network and host device do not need to be synchronized, and separate sampling

frequencies can be set.

SRC Mode

name

SRC

Number of channels

Sampling frequency [kHz]

Pullup/down

Data

length

Input

Output

Dante Host device*

144io N/A 144 144

44.1 ⇔ 44.1

48 ⇔ 48

88.2 ⇔ 88.2

96 ⇔ 96

Not supported 24/32

144io Sync SRC Synchronized 144 144

44.1 ⇔ 88.2

48 ⇔ 96

Not supported 24

72io Async SRC

Asynchronous

44.1/48/88.2/96 ⇔ 44.1/48/88.2/96

Supported

144i Async SRC

Asynchronous

144

44.1/48/88.2/96 ⇔ 44.1/48/88.2/96

Supported

144o Async SRC

Asynchronous

144

44.1/48/88.2/96 ⇔ 44.1/48/88.2/96

Supported

* The device to which the HY144-D-SRC is installed.

Manual Development Group

Published 07/2018 YJHH-A0

Yamaha HY144 Руководство пользователя

Бренд: Yamaha

Модель: HY144

Тип: Руководство пользователя

Yamaha HY144 — это универсальная карта расширения, предлагающая широкий спектр возможностей для работы с аудио.

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha HY144 User guide
français: Yamaha HY144 Mode d'emploi
italiano: Yamaha HY144 Guida utente
español: Yamaha HY144 Guía del usuario
Deutsch: Yamaha HY144 Benutzerhandbuch
Nederlands: Yamaha HY144 Gebruikershandleiding
português: Yamaha HY144 Guia de usuario
dansk: Yamaha HY144 Brugervejledning
polski: Yamaha HY144 instrukcja
čeština: Yamaha HY144 Uživatelská příručka
svenska: Yamaha HY144 Användarguide
日本語: Yamaha HY144 ユーザーガイド
Türkçe: Yamaha HY144 Kullanici rehberi
suomi: Yamaha HY144 Käyttöohjeet
română: Yamaha HY144 Manualul utilizatorului

Yamaha HY144 Руководство пользователя

Yamaha HY144 Руководство пользователя

на других языках

Похожие модели бренда