LG LF68V00S Инструкция по применению

LF68V00S

www.lg.com

OWNER’S MANUAL

FREE STANDING GAS COOKER

Please read this manual carefully before operating

your set and retain it for future reference.

MFL68462811

ENGLISH ARABICENGLISH AR

RUSSIAN

Dear Customer,

Our goal is to offer you products with high quality that exceed your expectations.

Your appliance is produced in modern facilities carefully and particularly tested for

quality.

This manual is prepared in order to help you use your appliance that is manufactured

by the most recent technology, with confidence and maximum efficiency.

Before using your appliance, carefully read this guide that includes the basic

information for right and safe installation, maintenance and use. Please contact to

the nearest Authorized Service for the installation of your product.

* Visuals used in this user manual are schematic and may vary depending on model.

CONTENTS:

1. BRIEF PRESENTATION OF PRODUCT

2. WARNINGS

3. INSTALLATION AND PREPARATIONS FOR USE

3.1 Environment where your appliance will be installed

3.2 Installation of product

3.3 Adjustment of feet

3.4 Gas connection

3.5 Electric connection and safety

3.6 Gas conversion

4. USE OF YOUR PRODUCT

4.1 Use of gas burners

4.1.1 Control of hob burners

4.1.2 Control of oven burner

4.1.3 Control of grill burner

4.1.4 Use of mechanical minute minder

4.2 Accessories used in oven

5. CLEANING AND MAINTENANCE

5.1 Cleaning

5.2 Maintenance

6. SERVICE AND TRANSPORT

6.1 Basic troubleshooting before contacting service

6.2 Information related to transport

1

2

11

12

13

14

15

1. BRIEF PRESENTATION OF PRODUCT

List of Components:

1- Lid

2- Cooktop

3- Control Panel

4- Oven Door Handle

5- Adjustable Feet

6- Oven Door

7- Oven Tray

8- Wire Grid

9- Grill Burner

10- Oven Lamp

11- Semi-Rapid(medium) Burner

12- Rapid (large) Burner

13- Auxillary (small) Burner

14- Pan Support

15- Semi-Rapid(medium) Burner

16- Oven Burner

DEPTH WIDTH HEIGHT

(cm) (cm) (cm)

60 60 90

9

10

1

2

3

4

5

6

7

8

* The appearance of your product may be different than the model shown above due to its aesthetic.

16

3

2. WARNINGS

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE USING YOUR

APPLIANCE, AND KEEP IT IN A CONVENIENT PLACE FOR REFERENCE WHEN NECESSARY.

THIS MANUAL IS PREPARED FOR MORE THAN ONE MODEL IN COMMON. YOUR

APPLIANCE MAY NOT HAVE SOME OF THE FEATURES THAT ARE EXPLAINED IN THIS

MANUAL. PAY ATTENTION TO THE EXPRESSIONS THAT HAVE FIGURES, WHILE YOU ARE

READING THE OPERATING MANUAL.

General Safety Warnings

- This appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they have

been given supervision or instruction concerning

use of the appliance in a safe way and

understand the hazards involved. Children shall

not play with the appliance. Cleaning

and user maintenance shall not be made by

children without supervision.

- The appliance is not intended for use by young

children or infirm persons without supervision. -

This appliance is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instruction concerning

use of the appliance by a person responsible for

their safety.

4

2. WARNINGS

- WARNING: The appliance and its accessible

parts become hot during use. Care should be

taken to avoid touching heating elements.

Children less than 8 years of age shall be kept

away unless continuously supervised.

- WARNING: Unattended cooking on a hob with

fat or oil can be dangerous and may result in

fire. NEVER try to extinguish a fire with water,

but switch off the appliance and then cover

flame e.g. with a lid or a fire blanket.

- WARNING: Danger of fire: do not store items

on the cooking surfaces.

- WARNING: If the surface is cracked, switch

off the appliance to avoid the possibility of

electric shock. - For hobs incorporating a lid,

any spillage should be removed from the lid

before opening. And also the hob surface

should be allowed to cool before closing the lid.

- The appliance is not intended to be operated

by means of an external timer or separate

remote-control system.

- WARNING: In order to prevent tipping of the

appliance, the stabilizing brackets must be

installed. (For detail information please read the

anti-tilting kit set guide.)

5

2. WARNINGS

- During use, the appliance becomes hot. Care

should be taken to avoid touching heating

elements inside the oven.

- During use, handles held for short periods in

normal use can get hot.

- Do not use harsh abrasive cleaners or sharp

metal scrapers to clean the oven door glass and

other surface since they can scratch the surface,

which may result in shattering of the glass or

damage to the surface.

- Do not use steam cleaners for cleaning the

appliance.

- WARNING: Ensure that the appliance is

switched off before replacing the lamp to avoid

the possibility of electric shock.

- WARNING: Accessible parts may be hot when

the cooking or grilling is in use. Young children

should be kept away.

- Your appliance is produced in accordance with all applicable local and international

standards and regulations.

- Maintenance and repair work must be made only by authorized service technicians.

Installation and repair work that is carried out by unauthorized technicians may endanger

you. It is dangerous to alter or modify the specifications of the appliance in any way.

- Prior to installation, ensure that the local distribution conditions (nature of the gas and gas

pressure or electricity voltage and frequency) and the requirements of the appliance are

compatible. The requirements for this appliance are stated on the label.

CAUTION: This appliance is designed only for cooking food and is intended for indoor

domestic household use only and should not be used for any other purpose or in any other

application, such as for non-domestic use or in a commercial environment or room heating.

- Do not try to lift or move the appliance by pulling the door handle.

6

2. WARNINGS

- This appliance is not connected to a combustion products evacuation device. It shall be

installed and connected in accordance with current installation regulations. Particular

attention shall be given to the relevant requirements regarding ventilation.

- If after 15 s the burner has not lit, stop operating the device and open the compartment

door and/or wait at least 1 min before attempting a further ignition of the burner.

- These instructions are only valid if the country symbol appears on the appliance. If the

symbol does not appear on the appliance, it is necessary to refer to the technical

instructions which will provide the necessary instructions concerning modification of the

appliance to the conditions of use of the country.

- All possible security measures have been taken to ensure your safety. Since the glass

may break, you should be careful while cleaning to avoid scratching. Avoid hitting or

knocking on the glass with accessories.

- Ensure that the supply cord is not wedged during the installation. If the supply cord is

damaged, it must be replaced by the manufacturer, its service agent or similarly qualified

persons in order to prevent a hazard.

- While the oven door is open, do not let children climb on the door or sit on it.

Installation Warnings

- Do not operate the appliance before it is fully installed.

- The appliance must be installed by an authorized technician and put into use. The

producer is notresponsible for any damage that might be caused by defective placement

and installation by unauthorized people.

- When you unpack the appliance, make sure that it is not damaged during transportation.

In case of any defect; do not use the appliance and contact a qualified service agent

immediately. As the materials used for packaging (nylon, staplers, styrofoam...etc) may

cause harmful effects to children, they should be collected and removed immediately.

- Protect your appliance against atmospheric effects. Do not expose it to effects such as

sun, rain, snow etc.

- The surrounding materials of the appliance (cabinet) must be able to withstand a

temperature of min 100°C.

During usage

- When you first run your oven a certain smell will emanate from the insulation materials

and the heater elements. For this reason, before using your oven, run it empty at maximum

temperature for 45 minutes. At the same time you need to properly ventilate the

environment in which the product is installed.

- During usage, the outer and inner surfaces of the oven get hot. While opening the oven

door, step back to avoid the hot steam coming out of the oven. There may be a risk of

burns.

- Do not put flammable or combustible materials, in or near the appliance when it is operating.

- Always use oven gloves to remove and replace food in the oven.

- Do not leave the cooker while cooking with solid or liquid oils. They may catch fire on

condition of extreme heating. Never pour water on to flames that are caused by oil. Cover the

saucepan or frypan with its cover in order to choke the flame that has occured in this case and

turn the cooker off.

- Always position pans over the centre of the cooking zone, and turn the handles to a safe

position so they cannot be knocked or grabbed.

- If you will not use the appliance for a long time, plug it off. Keep the main control switch

off. Also when you do not use the appliance, keep the gas valve off.

- Make sure the appliance control knobs are always in the "0" (stop) position when it is not

used.

- The trays incline when pulled out. Be careful not to let hot liquid spill over.

- WARNING: The use of a gas cooking appliance results in the production of heat,

moisture and products of combustion in the room in which it is installed. Ensure that the

kitchen is well ventilated especially when the appliance is in use, keep natural ventilation

holes open or install a mechanical ventilation device (mechanical extractor hood).

- Prolonged intensive use of the appliance may call for additional ventilation, for example

opening of a window, or more effective ventilation, for example increasing the level of

mechanical ventilation where present.

- While using the grill burner, keep the oven door open and always use the grill deflector

shield supplied with the product. Never use the grill burner with the oven door closed.

- CAUTION: Glass lids may shatter when heated.

Turn off all the burners before shutting the lid.

The hob surface should be allowed to cool before closing the lid.

- When the door or drawer of the oven is open, do not leave anything on it. You may

unbalance your appliance or break the cover.

- Do not put heavy things or flammable or ignitable goods (nylon, plastic bag, paper,

cloth...etc) into the drawer. This includes cookware with plastic accessories (e.g. handles).

- Do not hang towels, dishcloths or clothes from the appliance or its handles.

During cleaning and maintenance

-Please be careful while cleaning of oven internal cavity because some of inner

components may scratch during wiping.

- Always turn the appliance off before operations such as cleaning or maintenance. You

can do it after plugging the appliance off or turning the main switches off.- Do not remove

the control knobs to clean the control panel.

- Do not allow residues of sugary foods (such as jam) to set inside the oven. If left to set

for too long, they might damage the enamellining of the oven.

- If liquids are spilt on the closed lid, remove them thoroughly with a rag before opening it

Disposal

- For the protection of the environment, used appliances must be disposed of properly.

- The appliance must not be disposed of along with normal

domestic waste.

- Your local city council will inform you of times for uplifting special waste or identify public

disposal facilities for you.

TO MAINTAIN THE EFFICIENCY AND SAFETY OF YOUR APPLIANCE, WE

RECOMMEND YOU ALWAYS USE ORIGINAL SPARE PARTS AND TO CALL ONLY

OUR AUTHORIZED

SERVICE AGENTS IN CASE OF NEED.

7

2. WARNINGS

8

3. INSTALLATION AND PREPARATIONS FOR USE

This modern, functional and practical cooker, that was manufactured with the parts and materials of

highest quality, will meet your cooking needs in every aspect. You must surely read this manual so

that you don't have any problem in future and to be able to have satisfactory results. The following

information are the required rules for right installation and service processes. It must be read

especially by the technician who will install the appliance.

CAUTION: This appliance must be installed by a qualified people according to the

manufacturers installation instructions, local building regulations, gas authority codes and electrical

wiring instructions.

3.1 Environment where your appliance will be installed

• Your product must be set up and used in a place where it will always have ventilation.

• There must be a natural ventilation enough to provide the gas to be used in the environment.

The average air flow must directly come in through the air holes that will be opened on the walls

that are opened towards outside.

2

• These air holes must have at least the effective cross section of 100cm for fresh air circulation

(One or more air holes can be opened.). This hole (or holes) must be opened so that they are not

blocked. Preferably they must be placed close to the bottom and at opposite side of the smokes

of the burned gases that were emptied. If it seems not possible to open these ventilations in the

place where the appliance is set up, the needed air can also be obtained through the next room,

provided that this place is not a bedroom or a dangerous place. In this case this “next room”

must also be ventilated as required.

Emptying of the Burned Gases from Environment

The cooking appliances that operate with gas, throw the burned gas wastes out directly to the

outside or through the cooker hoods that are connected to the a chimney that opens directly to the

outside. If it seems not possible to install a cooker hood, it is required to set an electric fan on the

window or wall that has access to fresh air. This electric fan must have the capacity to change the air

of the kitchen environment 4-5 times of its own volume of air per hour.

!

Air inlet section

2

min. 100cm

Air inlet section

2

min. 100cm

Figure 1

Figure 2

9

3. INSTALLATION AND PREPARATIONS FOR USE

Cooker hood

flue

Electrical ventilator

Air inlet section

2

min. 100cm

Air inlet section

2

min. 100cm

Figure 3

Figure 4

3.2 Installation of product

There are some factors that must be paid attention to while installing your product. Surely be very

careful to while installing your product. Pay attention to our below instructions in order to be able

to prevent any problems and/or dangerous situations that may occur later.

• The appliance can be placed close to other furniture on condition that in the area where the

oven is set up, the furniture's height does not exceed the height of the cooker panel.

• Pay attention not to place it near the refrigerator, there must be no flammable or inflammable

materials such as curtain, waterproof cloth, etc. that will begin to burn quickly.

• It is required that there must be least a 2cm blank space around the product for air circulation.

• The furniture close to product must be manufactured resistant to temperatures up to 100°C.

• If the kitchen furniture are higher than the cooktop, it must be at least 10cm away from the

cooker's side.

The minimum heights from the pan support and wall cupboards to cooker hoods with fan over the

product, are shown in figure 5. Thus, the cooker hood must be at minimum 65cm height from the

pan support. If there is no cooker hood, this height must not be less than 70cm.

Figure 5

Min. 60cm

COOKER HOOD

Min. 42cm

Min. 65cm(with hood)

Min. 70cm(without hood)

3. INSTALLATION AND PREPARATIONS FOR USE

10

3.3 Adjustment of feet

Your product stands on 4 adjustable feet. When the product is

placed where to be used, check if the product is balanced. If it

is not balanced, you can make the adjustment by turning the

feet clockwise if required. It is possible to raise the appliance

maximum 30mm by the feet. If the feet are adjusted

appropriately, it is required not to move the appliance by

dragging, it should be moved by lifting it up.

3.4 Gas connection

Assembly of gas supply and leakage check

The connection of the appliance should be performed in accordance with local and international

standards and regulations applicable. You can find the information related to appropriate gas types

and appropriate gas injectors on technical data table. If the pressure of used gas is different than

these values stated or not stable in your area, it may be required to assemble an available pressure

regulator on the gas inlet. It is certainly required to contact to the authorized service to make these

adjusments.

The points that must be checked during flexible hose assembly

If the gas connection is made by a flexible hose that is fixed on the gas inlet of appliance, it must be

fixed by a pipe collar as well. Connect your appliance with a short and durable hose that is as close

as possible to the gas source. The hose's permitted maximum lenght is 1 m. The hose that brings

gas to the appliance must be changed once a year for your safety.

0

The hose must be kept clear from areas that may heat up to temperatures in excess of 90 C. The

hose must not be ruptured, bent or folded. It must be kept clear of sharp corners, moving things,

and should not be defective. Before assembly, it must be checked whether there is any production

defect.

As gas is turned on, all connection parts and hose must be checked with soapy water or leakage

fluids. Do not use naked flame to check gas leakage. All metal components used during gas

connection must be clear of rust. Also check the expiry dates of components to be used.

The points that must be checked during fixed gas connection assembly

To assemble a fixed gas connection (gas connection made by threads, e.g. a nut), there are different

methods used in different countries. The most common parts are already supplied with your appliance.

Any other part can be supplied as spare part.

During connections always keep the nut on the gas manifold fixed, while rotating the counter-part. Use

spanners of appropriate size for safe connection. For all surfaces between different components,

Figure 6

3. INSTALLATION AND PREPARATIONS FOR USE

11

always use the seals provided in the gas conversion kit. The seals used during connection should

also be approved to be used in gas connections. Do not use plumbing seals for gas connections.

Remember that this appliance is ready to be connected to gas supply in the country for which it has

been produced. The main country of destination is marked on the rear cover of the appliance. If you

need to use it in another country, any of the connections in the figure below can be required. In

such a case, learn the appropriate connection parts and obtain those parts to perform a safe

connection.

It is required to call the authorized service to be able to make the gas connections appropriately

and in compliance with safety standards.

CAUTION: Surely do not use any match or lighter for control of gas leakage.

3.5 Electric connection and safety

During the electric connection, follow the instructions stated in the user manual.

• The earthing cable must be connected to the earth terminal.

• You have to ensure the power cord with suitable insulation to be connected to the power source

during the connection. If there is no appropriate earthed electric outlet in accordance with

regulations in the place where the appliance to be installed, contact to our authorized service.

The earthed electric outlet must be close to the appliance.

• Do not use an extension cord.

• The power cord must not touch to the hot surface of the product.

• In case the cord is damaged, contact Authorized Service to have it changed.

• Any wrong electric connection may damage your appliance, as well as endangering your safety,

rendering your guarantee invalid.

!

Adapter

Gas Pipe Gas Pipe Gas Pipe Gas Pipe

Seal

Hose

Fitting

Gas Hose

with Collar

Mechanical

Gas Hose

Mechanical

Gas Hose

Mechanical

Gas Hose

Changing the gas inlet:

For some countries, the gas inlet type can be different for NG/LPG gases. In such a case, remove

the current connection components and nuts (if any) and connect the new gas supply accordingly.

In all conditions, all components used in gas connections should be approved by local and/or

international authorities. In all gas connections, refer to the “Assembly of gas supply and leakage

check” clause explained before.

Figure 7

12

• The appliance is adjusted for 230V 50Hz electricity. If the mains electricity is different contact

your authorized service.

L

N

BROWN

YELLOW+GREEN

BLUE

Figure 8

• The supply cord should be kept away from hot parts of appliance. Otherwise, the cord may be

damaged, causing short circuit.

• The manufacturer declares that it has no responsibility against any kind of damages and losses

that are caused by improper connections that are performed by unauthorized people.

3.6 Gas conversion

Caution : The following procedures must be undertaken by authorized service people.

Your appliance is adjusted to be operated with LPG/NG gas. The gas burners can be adapted to

different types of gas, by replacing the corresponding injectors and adjusting minimum flame length

suitable to the gas in use. For this purpose, following steps should be performed:

Changing injectors:

Hob Burners:

• Cut off the main gas supply and unplug from the electric mains.

• Remove the burner cap and the adapter(Figure 9).

• Unscrew the injectors. For this, use a 7mm spanner(Figure 10).

• Replace the injector with the ones from the gas conversion kit, with corresponding diameters

suitable to the type of gas that is going to be used, according to the information chart (which is

also supplied in the gas conversion kit).

3. INSTALLATION AND PREPARATIONS FOR USE

!

13

Oven/Grill Injectors:

The oven and grill injectors are assembled by a single screw that is placed on the tip of the burner.

For grill burners, this screw is already visible(Figure 11). Remove the screw, pull the grill burner to

yourself and you will see the injector revealed on the rear surface of the oven cavity (Figure 12).

For oven burners, open the drawer compartment and you will see the assembly screw below the

burner (Figure 13). Remove the screw, move the burner diagonally and the injector will be revealed on

the rear side of the burner box (Figure 12).

Remove the injectors with a 7mm spanner and replace the injector with the ones from the spare

set, with corresponding diameters suitable to the type of gas that is going to be used, according to

the information chart (which is also supplied in the gas conversion kit).

After conversion is completed, it is required to check gas leakage.

Adjusting the reduced flame position:

The flame length in the minimum position is adjusted with a flat screw located on the valve. For

valves with flame failure device, the screw is located on the side of the valve spindle(Figure 14). For

easier reduced flame adjustment, it is advised to remove the control panel (and microswitch, if

present) during adjustment.

3. INSTALLATION AND PREPARATIONS FOR USE

Figure 10

Injector

Spanner

Figure 12

Figure 11

Screw

Figure 13

Screw

Injector

Figure 9

3. INSTALLATION AND PREPARATIONS FOR USE

14

To determine the minimum position, ignite the burners and leave them on in minimum position.

Remove the with the help of a small screwdriver fasten or loosen the bypass screw around 90

angular degrees. When the flame has a length of at least 4mm, the gas is well distributed. Make

sure that the flame does not die out when passing from the maximum position to the minimum

position. Create an artificial wind with your hand toward the flame to see if the flames are stable.

For oven burner, operate the oven burner at minimum position for 5 minutes, then open and close

the oven door for 2-3 times to check the flame stability of the burner.

Reduced flame position adjustment is not required for grill burners.

The position the bypass screw must be loosened for conversion from LPG to NG. For conversion

from NG to LPG, the same screw must be fastened. Make sure that the appliance is unpluged from

the electric mains and the gas supply is open.

Figure 15

Bypass Screw

Figure 14

Bypass Screw

Valve with flame failure device

Thermostatic oven valve

4. USE OF YOUR PRODUCT

15

4.1 Use of gas burners

Ignition of the burners

To determine which knob controls which burner, check the position symbol above the knob.

• Manual Ignition of the Gas Burners

If your appliance is not equipped with any ignition aid or in case there is a failure in the electric

network, follow the procedures listed below:

For Hob Burners: To ignite one of the burners, press and turn its knob counter-clockwise so that the

knob is in maximum position, approach a match, taper or another manual aid to its upper

circumference. Move the ignition source away as soon as you see a stable flame.

For Oven Burner: To ignite the oven burner, press and turn the oven control knob counter-clockwise so

that the knob is in maximum position, approach a match, taper or another manual aid to the ignition

hole that is located on the front left corner of the burner. Move the ignition source away as soon as you

see a stable flame.

For Grill Burner: To ignite the grill burner, turn the grill valve in the clockwise position until the marker

on the knob points at the grill sign. Then, keep the knob pressed and approach a match, taper or

another manual aid to the holes that are situated on the burner. Move the ignition source away as soon

as you see a stable flame.

• Electrical Ignition

Ignition Through Hob Valve (micro switch): Press the valve of the burner you want to operate and

turn the valve in the counterclockwise direction (clockwise for the grill burner) so that the knob is in

maximum position while keeping the knob pressed. The spark plugs will generate sparks as long as

you keep the control knob pressed. The micro switch placed under the knob will automatically

create sparks through the spark plug of the burner. Continue pressing the knob until you see a

stable flame on the burner.

Control Panel

2

3

4

5

6

7

8

1

1-Turnspit and Oven Lamp Button

2- Timer

3- Oven Function Control Knob

4- Grill Control Knob

5- Gas Hob Kontrol Knob_Rear Left

6- Gas Hob Kontrol Knob_Front Left

7- Gas Hob Kontrol Knob_Front Right

8- Gas Hob Kontrol Knob_Rear Right

4. USE OF YOUR PRODUCT

16

Flame safety device:

Hob Burners

Hobs equipped with flame failure device provide security in case of accidentally extinguished flame.

If such a case occurs, the device will block the burners gas lines and will avoid any accumulation

of unburned gas. Wait 90 seconds before re-igniting an extinguished gas burner.

Oven / Grill Burners

Regardless of the model of your appliance, all oven burners are equipped with a gas safety device.

For this reason, during ignition, keep the oven knob pressed until you see stable flames. If the

flames are cut out after you release the knob, repeat the procedure again. If the oven burner does

not ignite after you keep the burner knob pressed for 30 seconds, open the oven door and do not

attempt re-ignition for at least 90 seconds. When oven flames go out accidentally, repeat the same

procedure.

4.1.1 Control of hob burners

The knob has 3 positions: Off (0), maximum (big flame symbol) and minimum (small flame symbol).

After you ignite the burner in maximum position; you can adjust the flame length between

maximum and min. positions. Do not operate the burners when the knob position is between

maximum and off positions.

After the ignition, check the flames visually. If you see yellow

tip, lifted or unstable flames; turn the gas flow off, and check

the assembly of burner caps and crowns (Figure 17). Also,

make sure that no liquid has flown into the burner cups. If

the burner flame goes out accidentally, turn the burner off,

ventilate the kitchen with fresh air, and do not attempt re-

ignition for 90 sec.

When turning the hob off, turn the knob in the clockwise

direction so that the knob shows "0" position or the marker

on the knob points upwards.

Figure 17

Cap

Crown

Spark

Plug

Burner

Cup

MAX. position

OFF position

Figure 16

MODULATE

MIN. position

4. USE OF YOUR PRODUCT

Your hob has burners of different diameters. The most economic way of using gas is to choose the

correct size gas burners for your cooking pan size and to bring the flame to minimum position once

the boiling point is reached. It is recommended to always cover your cooking pan.

In order to obtain maximum performance from the main burners, use pots with the following flat

bottom diameters. Using smaller pots than the minimum dimensions stated below will cause

energy loss.

Rapid / Wok Burner: 22-26cm

Semi-rapid Burner: 14-22cm

Auxiliary Burner: 12-18cm

Make sure that the tips of the flames do not spread out of the outer circumference of the pan, as

this may also harm the plastic accessories around the pan (handles etc.).

When the burners are not in use for prolonged periods, always turn the main gas control valve off.

WARNING:

• Use only flat pans and with a sufficiently thick base.

• Ensure that the base of the pan is dry before placing it on the burners.

• The temperature of accessible parts may be high when the appliance is operating. So it is

imperative to keep children and animals out of the reach of the burners during and after

cooking.

• After use, the hob remains very hot for a prolonged period of time, do not touch it and do not

place any object on top of the hob.

• Never place knives, forks, spoons and lids on the hob as they will get hot and could cause

serious burns.

Figure 18

!

CORRECT

INCORRECT

circular saucepan base

INCORRECT

saucepan’s base had not settled

INCORRECT

small saucepan diameter

Figure 19

17

Preheating

When you need to preheat the oven, we recommend you do so for 10 minutes. For recipes

needing high temperatures, e.g. bread, pastries, scones, soufflés etc., best results are achieved if

the oven is preheated first. For best results when cooking frozen or cooked chilled ready meals

always preheat the oven first.

Cooking

• Ensure that food is placed centrally on the shelf and there is sufficient room around the baking

tray/dish to allow for maximum circulation.

• Stand dishes on a suitably sized baking tray on the shelf to prevent spillage onto the oven base

and to help reduce cleaning.

• The material and finish of the baking tray and dishes used affect base browning. Enamel ware,

dark, heavy or non-stick utensils increase base browning. Shiny aluminum or polished steel

trays reflect the heat away and give less base browning.

• When cooking more than one dish in the oven, place dishes centrally on different shelves

rather than cluster several dishes on one shelf, this will allow the heat to circulate freely for the

best cooking results.

4.1.2 Control of Oven Burner

After you ignite the oven burner as explained before, you can adjust the temperature inside the

oven as you require, using the numbers on the control panel or knob ring: Bigger numbers mean

higher temperatures, while smaller numbers mean lower temperatures. If your oven is equipped

with an oven thermostat; refer to the temperature table below for the temperature references of

those numbers. Do not operate the appliance between "Off" position and first temperature

markerin the counter-clockwise direction. Always use the oven between maximum and minimum

numbers. When turning the oven off, turn the knob in the clockwise direction so that the knob

shows "0" position.

18

4. USE OF YOUR PRODUCT

60x60

TEMPERATURE

145

0

C

POSITION

MAX.

270

0

C

7

240

0

C

•

230

0

C

5

200

0

C

•

190

0

C

3

180

0

C

•

170

0

C

1

150

0

C

MIN.

Страница загружается ...

LG LF68V00S Инструкция по применению

LG LF68V00S Инструкция по применению

Похожие модели бренда

Модели других брендов