LED TV
user manual
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/register
Model _____________ Serial No. _____________
J5000-SQ_MI_BN68-08166K-00_L02.indb 1 2016-07-27 �� 1:31:26
English - 2
Important Safety Instructions
Warning! Important Safety Instructions
(Please read the appropriate section that corresponds to the marking on your
Samsung product before attempting to install the product.)
CAUTION
This symbol indicates that high voltage is present inside. It is
dangerous to make any kind of contact with any internal part
of this product.
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO
QUALIFIED PERSONNEL.
This symbol alerts you that important literature concerning
operation and maintenance has been included with this
product.
• The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable operation of this apparatus,
and to protect it from overheating, these slots and openings must never be blocked or covered.
− Do not cover this apparatus in a confined space, such as a bookcase, or built-in cabinet, unless proper ventilation is provided.
− Do not place this apparatus near or over a radiator or heat resistor, or where it is exposed to direct sunlight.
− Do not place a water containing vessel (vases etc.) on this apparatus, as this can result in a risk of fire or electric shock.
• Do not expose this apparatus to rain or place it near water (near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a
swimming pool etc.). If this apparatus accidentally gets wet, unplug it and contact an authorised dealer immediately. Make sure to pull out the power
cord from the outlet before cleaning.
• This apparatus use batteries. In your community there might be regulations that require you to dispose of these batteries properly under
environmental considerations. Please contact your local authorities for disposal or recycling information.
• Do not overload wall outlets, extension cords or adaptors beyond their capacity, since this can result in fire or electric shock.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular
attention to cords at plug end, adaptors and the point where they exit from the appliance.
• To protect this apparatus from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the set due to lightning and power line surges.
• Before connecting the AC power cord to the DC adaptor outlet, make sure the voltage designation of the DC adaptor corresponds to the local
electrical supply.
• Never insert anything metallic into the open parts of this apparatus. Doing so may create a danger of electric shock.
• To avoid electric shock, never touch the inside of this apparatus. Only a qualified technician should open this apparatus.
• Make sure to plug the power cord in until it is firmly inserted. When removing the power cord, make sure to hold the power plug when pulling the
plug from the outlet. Do not touch the power cord with wet hands.
• If this apparatus does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and
contact an authorised dealer or service centre.
• Be sure to pull the power plug out of the outlet if the TV is to remain unused or if you are to leave the house for an extended period of time (especially
when children, elderly or disabled people will be left alone in the house).
− Accumulated dust can cause an electric shock, an electric leakage or a fire by causing the power cord to generate sparks and heat or the
insulation to deteriorate.
• Be sure to contact an authorised service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity,
chemical substances or where it will operates for 24 hours a day such as in an airport, a train station, etc. Failure to do so may cause serious
damage to your set.
• Use only a properly grounded plug and receptacle.
• An improper ground may cause electric shock or equipment damage. (Class l Equipment only.)
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.
• Do not allow children to hang onto the product.
• Store the accessories (battery, etc.) in a location safely out of the reach of children.
• Do not install the product in an unstable location such as a shaky self, a slanted floor or a location exposed to vibration.
• Do not drop or impart any shock to the product. If the product is damaged, disconnect the power cord and contact a service centre.
• Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol,
thinners, insecticide, aerial freshener, lubricant or detergent. This may damage the appearance or erase the printing on the product.
• Apparatus shall not be exposed to dripping or splashing.
• Do not dispose of batteries in a fire.
• Do not short circuit, disassemble or overheat the batteries.
• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• WARNING - TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT
ALL TIMES.
English
J5000-SQ_MI_BN68-08166K-00_L02.indb 2 2016-07-27 �� 1:31:29
English - 3
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product
appearance. Product design and specifications may be changed without notice.
Important Warranty Information Regarding Television Format
Viewing
1. Functionalities related to Digital TV (DVB) are only available in countries/areas where DVB-T (MPEG2 and MPEG4
AVC) digital terrestrial signals are broadcasted or where you are able to access to a compatible DVB-C (MPEG2 and
MPEG4 AAC) cable-TV service. Please check with your local dealer the possibility to receive DVB-T or DVB-C signal.
2. DVB-T is the DVB European consortium standard for the broadcast transmission of digital terrestrial television and
DVB-C is that for the broadcast transmission of digital TV over cable. However, some differentiated features like
EPG (Electric Programme Guide), VOD (Video On Demand) and so on, are not included in this specification. So, they
cannot be workable at this moment.
3. Although this TV set meets the latest DVB-T and DVB-C standards, as of [August, 2008], the compatibility with
future DVB-T digital terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.
4. Depending on the countries/areas where this TV set is used some cable-TV providers may charge an additional fee
for such a service and you may be required to agree to terms and conditions of their business.
5. Some Digital TV functions might be unavailable in some countries or regions and DVB-C might not work correctly
with some cable service providers.
6. For more information, please contact your local Samsung customer care centre.
✎
The reception quality of TV may be affected due to differences in broadcasting method between the countries.
Please check the TV performance in the local SAMSUNG Authorised Dealer, or the Samsung Call Centre
whether it can be improved by reconfiguring TV setting or not.
J5000-SQ_MI_BN68-08166K-00_L02.indb 3 2016-07-27 �� 1:31:30
English - 4
List of Features
•
Media Play
: Allows you to play music files, pictures, and movies saved on a USB device.
•
e-Manual
: Allows you to read on screen full manual. (p. 8)
Accessories
✎
Please make sure the following items are included with your TV. If any items are missing, contact your dealer.
✎
The items’ colours and shapes may vary depending on the models.
✎
Cables not included in the package contents can be purchased separately.
[
CAUTION: INSERT SECURELY LEST SHOULD BE DETACHED IN SET
• Remote Control & Batteries (AAA x 2) • Power Cord
• Regulatory Guide / Warranty Card (Not available in some locations) • User Manual
Wall mount Adapter (Only for 40")
Cable Holder
(Not available in some locations)
Assembling the Cable Holder
J5000-SQ_MI_BN68-08166K-00_L02.indb 4 2016-07-27 �� 1:31:31
English - 5
Viewing the Remote Control
✎
This remote control has Braille points on the
Power
,
Channel
,
Volume
and
Enter
buttons and can be used by visually
impaired persons.
Turns the TV on and off.
Displays and selects the available
video sources.
Returns to the previous channel.
Cuts off the sound temporarily.
Changes channels.
Displays channel lists on the screen.
Displays the EPG (Electronic
Programme Guide).
Displays information on the TV
screen.
Exits the menu.
Press to directly access to channels.
Adjusts the volume.
Alternately select Teletext ON, Double,
Mix or OFF.
Displays the main on-screen menu.
Quickly select frequently used
functions.
Displays
Media Play
.
Returns to the previous menu.
Selects the on-screen menu items and
changes the values seen on the menu.
Use these buttons according to the
direction on screen.
Use these buttons in a specific
feature.
For details, refer to the e-Manual.
E-MANUAL
: Displays the
e-Manual
.
(p. 8)
PIC SIZE
: Change the picture size.
AD/SUBT.:
Audio Description selection.
(Not available in some locations) /
Displays digital subtitles.
J5000-SQ_MI_BN68-08166K-00_L02.indb 5 2016-07-27 �� 1:31:32
English - 6
Installing batteries (Battery size: AAA)
Using the TV’s Controller (Panel Key)
The TV's Controller at the right bottom of the TV, lets you control the TV without the remote control.
: Turns the TV on or off.
/ : Changes channels.
/ : Adjusts the volume.
: Displays and selects the available video sources.
Control Menu
Remote control sensor/TV Controller
Press: Move
Press & Hold: Select
✎
If you press it first, the control menu appears. You can select the function by pressing and holding the TV's
Controller
✎
The product colour and shape may vary depending on the model.
✎
With the TV's Controller, you cannot perform other operations except for turning the TV on or off, changing the
channel, adjusting the volume, and switching the input source.
Standby mode
Do not leave your TV in standby mode for long periods of time (when you are away on a holiday, for example). A small
amount of electric power is still consumed even when the power button is turned off. It is best to unplug the power cord.
J5000-SQ_MI_BN68-08166K-00_L02.indb 6 2016-07-27 �� 1:31:34
English - 7
Initial Setup
When the TV is initially powered on, a sequence of on-screen prompts will assist in configuring basic settings. Press the
POWER
P button.
Setup
is available only when the source is set to TV.
✎
If you connect any device to
HDMI IN 1 (STB)
before starting the installation,
Channel Source
will be changed to
Set-top
box
automatically. If you do not want to select
Set-top box
, please select
Aerial
.
If You Want to Reset This Feature...
Select
System
-
Setup
(Initial Setup). Enter your 4 digit PIN number. The default password is “0-0-0-0”. If you want to
change the PIN number, use the
Change PIN
function.
You should do Setup (
MENU
→ System) again at home even though you did in shop already.
✎
If you forget the PIN code, press the remote control buttons in the following sequence in Standby mode, which
resets the PIN to “0-0-0-0”:
MUTE
→ 8 → 2 → 4 →
POWER
(on)
Changing the Input Source
Source
TV / HDMI1 / HDMI2/DVI / AV / Component
Use to select TV or other external input sources such as DVD / Blu-ray players / cable box / STB satellite receiver
connected to the TV.
✎
Press the
SOURCE
button. In the displayed
Source
list, connected inputs will be highlighted.
✎
PC(D-Sub) input is not supported. If you want to connect PC to the TV, you can connect the HDMI to DVI cable with
the
HDMI IN 2 (DVI)
port on the TV.
✎
Press the
TOOLS
button.
• Edit Name
You can set an external input source name you want.
− When connecting a PC to the
HDMI IN 2 (DVI)
port with HDMI cable, you should set the TV to PC mode under
Edit Name.
− When connecting a PC to the
HDMI IN 2 (DVI)
port with HDMI to DVI cable, you should set the TV to DVI PC
mode under
Edit Name
.
− When connecting an AV devices to the
HDMI IN 2 (DVI)
port with HDMI to DVI cable, you should set the TV to DVI
Devices mode under
Edit Name
.
• Information
You can see detailed information about the connected external device.
J5000-SQ_MI_BN68-08166K-00_L02.indb 7 2016-07-27 �� 1:31:36
English - 8
How to use the e-Manual
You can find instructions about your TV’s features in the
e-Manual
in your TV. To use, press the
E-MANUAL
button on your remote. Move the cursor using the up/down/right/left buttons to highlight a
category, then a topic, and then press the
ENTER
E button. The
e-Manual
displays the page you want
to see.
You can also access it through the menu:
O
MENU
m →
Support
→
e-Manual
→
ENTER
E
✎
To return to the
e-Manual
main menu, press the
E-MANUAL
button on the remote.
Screen Display
Basic Features
Changing the Preset Picture Mode
Adjusting Picture Settings
Changing the Picture Options
Changing the Preset Sound Mode
Adjusting Sound Settings
}
Index
E
Enter
e
Exit
Currently displayed
video, TV
Programme, etc.
The category list. Press l or r button to
select the category you want.
Displays the sub-menu list. Use the arrow
buttons on your remote to move the cursor.
Press
ENTER
E button to select the sub-
menu you want.
Operation Buttons
}
Index
: Displays the index screen.
− Index available depending on the language.
E
Enter
: Selects a category or sub-menu.
e
Exit
: Exit the e-Manual.
<Viewing the Contents>
a
Try Now
: Displays the OSD menu that corresponds to the topic. To return to the e-Manual screen, press the
E-MANUAL
button.
b
Home
: Moves to the e-Manual home screen.
L
Page
: Moves to previous or next page.
{
Zoom
: Magnifies a screen.
− Press the { (
Zoom
) button to magnify the screen. You can scroll through the magnified screen by using the u or
d buttons. To return to the screen to normal size, press the
RETURN
button.
J5000-SQ_MI_BN68-08166K-00_L02.indb 8 2016-07-27 �� 1:31:38
English - 9
How to toggle between an e-Manual topic and the corresponding OSD menu(s).
✎
This function is not enabled in some menus.
✎
You cannot use the Try Now function if the menu is not activated.
Method 1 Method 2
1. If you want to use the menu that corresponds to an
e-Manual topic, press the red button to select
Try
Now
.
2. To return to the
e-Manual
screen, press the
E-MANUAL
button.
1. Press the
ENTER
E button when a topic is
displayed. “
Are you sure?
” appears. Select
Yes
, and
then press the
ENTER
E button. The OSD window
appears.
2. To return to the
e-Manual
screen, press the
E-MANUAL
button.
How to search for a topic on the index page
✎
This function may not be supported depending on the language.
1. If you want to search a keyword, press the blue button to select
Index
.
2. Press the l or r button to select a character order you want.
3. Press the u or d button to select a keyword you want to see, and then press the
ENTER
E button.
4. You can view the corresponding e-Manual instruction screen.
✎
To close the
Index
screen, press the
RETURN
button.
J5000-SQ_MI_BN68-08166K-00_L02.indb 9 2016-07-27 �� 1:31:39
English - 10
Teletext Feature
The index page of the Teletext service gives you information on how to use the service. For Teletext information to be
displayed correctly, channel reception must be stable. Otherwise, information may be missing or some pages may not
be displayed.
✎
You can change Teletext pages by pressing the numeric buttons on the remote control.
1
0 (mode): Selects the Teletext mode (LIST/FLOF). If pressed during LIST
mode, switches the mode to List save mode. In List save mode, you can
save a Teletext page into a list using the 8(store) button.
2
/ (Full TTX/Double TTX/Mix/Off): Activates the Teletext mode for the
current channel. Press the button twice to overlap the Teletext mode with the
current broadcasting screen. Press it one more time to exit Teletext.
3
1 (sub-page): Displays the available sub-page.
4
8 (store): Stores the Teletext pages.
5
6 (index): Displays the index (contents) page at any time while you are
viewing Teletext.
6
4 (size): Displays the Teletext on the upper half of the screen in double-size.
To move the text to the lower half of the screen, press it again. For normal
display, press it once again.
7
9 (hold): Holds the display at the current page, in the case that there are
several secondary pages that follow automatically. To undo, press it again.
8
2 (page up): Displays the next Teletext page.
9
3 (page down): Displays the previous Teletext page.
0
5 (reveal): Displays the hidden text (answers to quiz games, for example).
To display the normal screen, press it again.
!
7 (cancel): Shrinks the Teletext display to overlap with the current
broadcast.
@
Colour buttons (red, green, yellow, blue): If the FASTEXT system is used by
the broadcasting company, the different topics on a Teletext page are colour-
coded and can be selected by pressing the coloured buttons. Press the
colour corresponding to the topic of your choice. A new colour coded page
is displayed. Items can be selected in the same way. To display the previous
or next page, press the corresponding coloured button.
The Teletext pages are organized according to six categories
Part
Contents
A
E
F
B C D
A Selected page number.
B Broadcasting channel identity.
C Current page number or search indications.
D Date and time.
E Text.
F Status information. FASTEXT information.
J5000-SQ_MI_BN68-08166K-00_L02.indb 10 2016-07-27 �� 1:31:41
English - 11
Troubleshooting
If the TV seems to have a problem, first try this list of possible problems and solutions. If none of these troubleshooting
tips apply, visit “www.samsung.com”, then click on Support, or call Samsung customer service centre.
Issues Solutions and Explanations
Picture Quality
First of all, please perform the
Picture Test
and confirm that your TV is properly displaying test image.
(go to
MENU
-
Support - Self Diagnosis - Picture Test
) If the test image is properly displayed, the poor
picture may caused by the source or signal.
The TV image does not look as
good as it did in the store.
• If you have an analogue cable/set top box, upgrade to a digital set top box. Use HDMI or Component
cables to deliver HD (high definition) picture quality.
• Cable/Satellite subscribers: Try HD stations from the channel line up.
• Aerial connection: Try HD stations after performing Auto tuning.
• Many HD channels are up scaled from SD (Standard Definition) contents.
• Adjust the Cable/Set top box video output resolution to 1080i or 720p.
• Make sure you are watching the TV at the minimum recommended distance based on the size and
definition of the signal.
The picture is distorted:
macroblock error, small block,
dots, pixelization
• Compression of video contents may cause picture distortion especially in fast moving pictures such as
sports and action movies.
• Low signal level or bad quality can cause picture distortion. This is not a TV issue.
• Mobile phones used close to the TV (cca up to 1m) may cause noise in picture on analogue and digital
T V.
Colour is wrong or missing.
• If you’re using a component connection, make sure the component cables are connected to the correct
jacks. Incorrect or loose connections may cause colour problems or a blank screen.
There is poor colour or
brightness.
• Adjust the Picture options in the TV menu. (go to Picture Mode / Colour / Brightness / Sharpness)
• Adjust Energy Saving option in the TV menu. (go to MENU - System - Eco Solution - Energy Saving)
• Try resetting the picture to view the default picture settings. (go to MENU - Picture - Reset Picture)
There is a dotted line on the
edge of the screen.
• If the picture size is set to Screen Fit, change it to 16:9.
• Change cable/satellite box resolution.
The picture is black and white.
• If you are using an AV composite input, connect the video cable (yellow) to the Green jack of
component input 1 on the TV.
When changing channels, the
picture freezes or is distorted
or delayed.
• If connected with a cable box, please try to reset the cable box. Reconnect the AC cord and wait until
the cable box reboots. It may take up to 20 minutes.
• Set the output resolution of the cable box to 1080i or 720p.
Sound Quality
First of all, please perform the Sound Test to confirm that your TV audio is properly operating. (go to
MENU - Support - Self Diagnosis - Sound Test)
If the audio is ok, the sound problem may be caused by the source or signal.
There is no sound or the sound
is too low at maximum volume.
• Please check the volume of the device (Cable/Sat Box, DVD, Blu-ray etc) connected to your TV.
J5000-SQ_MI_BN68-08166K-00_L02.indb 11 2016-07-27 �� 1:31:42
English - 12
Issues Solutions and Explanations
The picture is good but there is
no sound.
• Set the Speaker Select option to TV Speaker in the sound menu.
• If you are using an external device, make sure the audio cables are connected to the correct audio input
jacks on the TV.
• If you are using an external device, check the device’s audio output option (ex. you may need to change
your cable box’s audio option to HDMI when you have a HDMI connected to your TV).
• If you are using a DVI to HDMI cable, a separate audio cable is required.
• Reboot the connected device by reconnecting the device’s power cable.
The speakers are making an
inappropriate noise.
• Check the cable connections. Make sure a video cable is not connected to an audio input.
• For aerial or cable connections, check the signal strength. Low signal level may cause sound distortion.
No Picture, No Video
The TV will not turn on.
• Make sure the AC power cord is securely plugged in to the wall outlet and the T V.
• Make sure the wall outlet is working.
• Try pressing the
POWER
button on the TV to make sure the problem is not the remote. If the TV turns
on, refer to “The remote control does not work” below.
The TV turns off automatically.
• Ensure the Sleep Timer is set to Off in the Time menu.
• If your PC is connected to the TV, check your PC power settings.
• Make sure the AC power cord is plugged in securely to the wall outlet and the TV.
•
No Signal Power Off
turns off the TV if no signal has been received by the TV for a specified period time.
Auto Power Off turns off the TV if there has been no user input in four hours.
There is no picture/video.
• Check cable connections (remove and reconnect all cables connected to the TV and external devices).
• Set your external device’s (Cable/Set top Box, DVD, Blu-ray etc) video outputs to match the
connections to the TV input. For example, if an external device’s output is HDMI, it should be connected
to an HDMI input on the TV.
• Make sure your connected devices are powered on.
• Be sure to select the TV’s correct source by pressing the
SOURCE
button on the remote control.
• Reboot the connected device by reconnecting the device’s power cable.
Aerial (Air/Cable) Connection
The TV is not receiving all
channels.
• Make sure the Aerial cable is connected securely.
• Please try
Setup
(Initial setup) to add available channels to the channel list. Go to
MENU
-
System -
Setup
(Initial setup) and wait for all available channels to be stored.
• Verify the Aerial is positioned correctly.
The picture is distorted: macro
block error small block, dots,
pixelization
• Compression of video contents may cause picture distortion, especially on fast moving pictures such as
sports and action movies.
• A low signal can cause picture distortion. This is not a TV issue.
Others
The picture will not display in
full screen.
• HD channels will have black bars on either side of the screen when displaying up scaled SD (4:3)
contents.
• Black bars on the top and bottom will appear during movies that have aspect ratios different from your
T V.
• Adjust the picture size options on your external device or TV to full screen.
The remote control does not
work.
• Replace the remote control batteries with the poles (+/–) in the right direction.
• Clean the sensor’s transmission window on the remote.
• Try pointing the remote directly at the TV from 1.5 ~ 1.8m away.
J5000-SQ_MI_BN68-08166K-00_L02.indb 12 2016-07-27 �� 1:31:43
English - 13
Issues Solutions and Explanations
The cable/set top box remote
control doesn’t turn the TV on
or off, or adjust the volume.
• Programme the Cable/Set top box remote control to operate the TV. Refer to the Cable/Set top box
user manual for the SAMSUNG TV code.
A “
Mode Not Supported
”
message appears.
• Check the supported resolution of the TV, and adjust the external device’s output resolution accordingly.
There is a plastic smell from
the TV.
• This smell is normal and will dissipate over time.
The TV Signal Information
is unavailable in the Self
Diagnosis Test menu.
• This function is only available with digital channels from an Aerial / RF / Coax connection.
TV is tilted to the right or left
side.
• Remove the stand base from the TV and reassemble it.
There are difficulties
assembling the stand base.
• Make sure the TV is placed on a flat surface. If you cannot remove the screws from the TV, please use a
magnetized screw driver.
The
Broadcasting
menu is grey
out (unavailable).
• The
Broadcasting
menu is only available when the TV source is selected.
Your settings are lost after 5
minutes or every time the TV is
turned off.
• If the TV is in the Store Demo mode, it will reset audio and picture settings every 5 minutes. If you want
to change the settings from Store Demo mode to Home Use, press the SOURCE button to select TV
mode, and go to MENU - Support - Use Mode.
You have intermittent loss of
audio or video.
• Check the cable connections and reconnect them.
• Loss of audio or video can be caused by using overly rigid or thick cables. Make sure the cables are
flexible enough for long term use. If mounting the TV to the wall, we recommend using cables with 90
degree connectors.
You see small particles when
you look closely at the edge of
the frame of the TV.
• This is part of the product’s design and is not a defect.
The
PIP
menu is not available.
•
PIP
functionality is only available when you are using a HDMI or components source.
You turned the TV off 45
minutes ago, and it turned on
again.
• It is normal. The TV operates the OTA (Over The Aerial) function itself to upgrade firmware downloaded
whilst your watching TV.
The message “
Scrambled
Signal
” or “
Weak or No Signal
”
appears.
• If you are using a CAM CARD (CI/CI+), check that it is installed into the common interface slot.
• If there is still a problem, pull the CAM CARD out of the TV and insert it into the slot again.
There are recurrent picture/
sound issues.
• Check and change the signal/source.
A reaction may occur between
the rubber cushion pads on the
base stand and the top finish
of some furniture.
• To prevent this, use felt pads on any surface of the TV that comes in direct contact with furniture.
The message “
This file may not
be playable properly.
” appears.
• This may appear because of high bit rate of content. Content generally will play but could experience
some playability issue.
✎
You can keep your TV in optimum operating condition by upgrading to the latest firmware (www.samsung.com →
support) by USB.
✎
This TFT LED panel uses a panel consisting of sub pixels which require sophisticated technology to produce.
However, there may be a few bright or dark pixels on the screen. These pixels will have no impact on the
performance of the product.
✎
Some functions and pictures shown in this manual are available on specific models only.
J5000-SQ_MI_BN68-08166K-00_L02.indb 13 2016-07-27 �� 1:31:45
English - 14
Installing the Wall Mount
Installing other Wall Mount Kits, Please refer as follow:
The wall mount kit (sold separately) allows you to mount the TV on the wall. For detailed information on installing the wall
mount, see the instructions provided with the wall mount. Contact a technician for assistance when installing the wall
mount bracket. We do not advice you to do it yourself.
Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you select to
install the TV on your own.
TV
Wall mount
Bracket
C
TV
Wall mount
Bracket
C
Wall mount
Adapter
48 inche
40 inche
Before installing any other wall mounting kit, assemble the wall mount adapter provided separately with the TV. (Only for
40")
Wall Mount Kit Specifications (VESA)
✎
Wall mount kit is not supplied but sold separately.
✎
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please
contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
✎
NOTE
• Standard dimensions for wall mount kits are shown in the table below.
• When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are
provided.
• Do not use screws that do not comply with the VESA standard screw specifications.
• Do not use screws longer than the standard dimension, as they may cause damage to the inside of the TV set.
• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may
differ depending on their specifications.
• Do not fasten the screws too strongly, this may damage the product or cause the product to fall, leading to
personal injury. Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is
used or the consumer fails to follow the product installation instructions.
• Do not exceed 15 degrees tilt when mounting this TV.
inches VESA Spec. (A * B) Standard Screw Quantity
40
200 x 200 M8 4
48
Do not install your Wall Mount Kit while your TV is turned on. It may result in personal injury due to electric
shock.
J5000-SQ_MI_BN68-08166K-00_L02.indb 14 2016-07-27 �� 1:31:48
English - 15
Securing the TV to the Wall
Caution
: Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular, ensure
your children do not hang on or destabilize the TV. Doing so may cause the TV to tip over,
causing serious injuries or death. Follow all safety precautions provided in the Safety Flyer
included with your TV. For added stability and safety, you can purchase and install the anti-
fall device as described below.
To avoid the TV from falling
1. Put the screws into the clamps and firmly fasten them onto the wall.
Confirm that the screws have been firmly installed onto the wall.
✎
You may need additional material such as an anchor depending
on the type of wall.
✎
Since the necessary clamps, screws, and string are not supplied,
please purchase these additionally.
2. Remove the screws from the centre back of the TV, put the screws
into the clamps, and then fasten the screws onto the TV again.
✎
Screw Specifications
• For a 40 - 48 inches: M8
3. Connect the clamps fixed onto the TV and the clamps fixed onto the
wall with a strong string and then tie the string tightly.
✎
NOTE
• Install the TV near to the wall so that it does not fall backwards.
• It is safe to connect the string so that the clamps fixed on the
wall are equal to or lower than the clamps fixed on the TV.
• Untie the string before moving the TV.
4. Verify all connections are properly secured. Periodically check
connections for any sign of fatigue for failure. If you have any doubt
about the security of your connections, contact a professional
installer.
Wall
• The product colour and shape may
vary depending on the model.
J5000-SQ_MI_BN68-08166K-00_L02.indb 15 2016-07-27 �� 1:31:50
English - 16
Securing the Installation Space
Keep the required distances between the product and other objects (e.g. walls) to ensure proper ventilation.
Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature of the
product.
✎
When using a stand or wall-mount, use parts provided by Samsung Electronics only.
• If you use parts provided by another manufacturer, it may result in a problem with the product or an injury due to
the product falling.
✎
The appearance may differ depending on the product.
✎
Be careful when you contact the TV because some parts can be somewhat hot.
Installation with a stand. Installation with a wall-mount.
10 cm10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
Storage and Maintenance
✎
If you remove the attached sticker on the TV screen, clean the residues and then watch TV.
✎
The exterior and screen of the product can get scratched during cleaning. Be sure to wipe the exterior and screen
carefully using a soft cloth to prevent scratches.
Do not spray water directly onto the product. Any liquid that goes
into the product may cause a failure, fire, or electric shock.
Clean the product with a soft cloth dampened with a small amount
of water. Do not use a flammable liquid (e.g. benzene, thinners) or
a cleaning agent.
J5000-SQ_MI_BN68-08166K-00_L02.indb 16 2016-07-27 �� 1:31:51
English - 17
Anti-theft Kensington Lock
The Kensington Lock is not supplied by Samsung. It is a device used to physically fix the system when using it in a
public place. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer
to the manual provided with the Kensington Lock for additional information on proper use.
✎
Please find a “K” icon on the rear of the TV. A kensington slot is beside the “K” icon.
✎
The position and colour may differ depending on the model.
<Optional>
To lock the product, follow these steps:
1. Wrap the Kensington lock cable around a large, stationary object such as desk or chair.
2. Slide the end of the cable with the lock attached through the looped end of the Kensington lock cable.
3. Insert the locking device into the Kensington slot on the product.
4. Lock the lock.
✎
These are general instructions. For exact instructions, see the User manual supplied with the locking device.
✎
The locking device has to be purchased separately.
J5000-SQ_MI_BN68-08166K-00_L02.indb 17 2016-07-27 �� 1:31:52
English - 18
Specifications
Display Resolution
1920 x 1080
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
10°C to 40°C (50°F to 104°F)
10% to 80%, non-condensing
-20°C to 45°C (-4°F to 113°F)
5% to 95%, non-condensing
Sound (Output)
10W x 2
Model Name
UA40J5000 UA48J5000
Screen Size
40 Inches 48 Inches
Dimensions (W x H x D)
Body
With stand
922.7 x 530.7 x 72.0 mm
922.7 x 590.5 x 288.1 mm
1098.7 x 638.7 x 73.9 mm
1098.7 x 699.5 x 310.5 mm
Weight
Without Stand
With Stand
6.4 kg
7.4 kg
10.2 kg
11.3 kg
✎
Design and specifications are subject to change without prior notice.
✎
For information about power supply, and more about power consumption, refer to the label attached to the product.
J5000-SQ_MI_BN68-08166K-00_L02.indb 18 2016-07-27 �� 1:31:53
English - 19
Supported Video Formats
File Extention Container Video Codec Resolution Frame rate (fps)
Bit rate
(Mbps)
Audio Codec
*.avi
*.mkv
*.asf
*.wmv
*.mp4
*.3gp
*.vro
*.mpg
*.mpeg
*.ts
*.tp
*.trp
*.mov
*.flv
*.vob
*.svi
*.divx
AVI
MKV
ASF
MP4
3GP
VRO
VOB
PS
TS
Divx 3.11 / 4 / 5 / 6
1920 x 1080
6 ~ 30
30
Dolby Digital
LPCM
ADPCM (IMA, MS)
AAC
HE-AAC
WMA
Dolby Digital Plus
MPEG (MP3)
DTS (Core)
G.711 (A-Law, μ-Law)
MPEG4 SP/ASP
H.264 BP/MP/HP
Motion JPEG 640 x 480 8
Window Media Video v9
1920 x 1080 30
MPEG2
MPEG1
✎
Other Restrictions
• Video content will not play, or not play correctly, if there is an error in the content or the container.
• Sound or video may not work if the contents have a standard bit rate/frame rate above the compatible Frame/sec
listed in the table.
• If the Index Table is in error, the Seek (Jump) function is not supported.
• Some USB/digital camera devices may not be compatible with the player.
• The menu can be displayed late if the video is over 10Mbps(bit rate).
Video decoder Audio decoder
• Supports up to H.264, Level 4.1 (FMO/ASO/RS
are not supported.)
• frame rate:
− Below 1280 x 720: 60 frame max
− Above 1280 x 720: 30 frame max
• VC1 AP L4 is not supported.
• GMC 2 or higher is not supported.
• WMA 10 Pro supports up to 5.1 channel and M2
profile.
• WMA lossless audio is not supported.
• Vorbis supports up to 2ch.
• DD+ supports up to 5.1 channel.
Supported Subtitle Formats
• External
Name File extension
MPEG-4 timed text .ttxt
SAMI .smi
SubRip .srt
SubViewer .sub
Micro DVD .sub or .txt
SubStation Alpha .ssa
Advanced SubStation Alpha .ass
Powerdivx .psb
• Internal
Name Container Format
Xsub AVI Picture Format
SubStation Alpha MKV Tex t Format
Advanced SubStation Alpha MKV Text Format
SubRip MKV Text Format
MPEG-4 Timed text MP4 Text Format
J5000-SQ_MI_BN68-08166K-00_L02.indb 19 2016-07-27 �� 1:31:55
English - 20
Supported Photo Formats
File Extension Type Resolution
*.jpg
*.jpeg
JPEG 15360 X 8640
*.bmp BMP 4096 X 4096
*.mpo MPO 15360 X 8640
✎
The MPO type file does not support Zoom, Rotate
and Slide Show Effect functions.
Supported Music Formats
File Extension Type Codec Remark
*.mp3 MPEG
MPEG1 Audio
Layer 3
*.m4a
*.mpa
*.aac
MPEG4 AAC
*.flac FLAC FLAC Supports up to 2ch.
*.ogg OGG Vorbis Supports up to 2ch.
*.wma WMA WMA
WMA 10 Pro supports up to 5.1
channel and M2 profile. (WMA
lossless audio is not supported.)
*.wav wav wav
*.mid
*.midi
midi midi type 0 and type 1
Full available resolution
Optimal resolution is 5 series: 1920 x 1080@60Hz. See specification page for full available resolution.
Mode Resolution
Horizontal
Frequency (KHz)
Vertical Frequency
(Hz)
Pixel Clock
Frequency (MHz)
Sync Polarity
(H / V)
1920 X 1080
IBM 720 x 400 31.469 70.087 28.322 -/+
c
MAC
640 x 480 35.000 66.667 30.240 -/-
c
832 x 624 49.726 74.551 57.284 -/-
c
1152 x 870 68.681 75.062 100.000 -/-
c
VESA DMT
640 x 480 31.469 59.940 25.175 -/-
c
640 x 480 37.861 72.809 31.500 -/-
c
640 x 480 37.500 75.000 31.500 -/-
c
800 x 600 37.879 60.317 40.000 +/+
c
800 x 600 48.077 72.188 50.000 +/+
c
800 x 600 46.875 75.000 49.500 +/+
c
1024 x 768 48.363 60.004 65.000 -/-
c
1024 x 768 56.476 70.069 75.000 -/-
c
1024 x 768 60.023 75.029 78.750 +/+
c
1152 x 864 67.500 75.000 108.000 +/+
c
1280 x 720 45.000 60.000 74.250 +/+
c
1280 x 800 49.702 59.810 83.500 -/+
c
1280 x 1024 63.981 60.020 108.000 +/+
c
1280 x 1024 79.976 75.025 135.000 +/+
c
1366 x 768 47.712 59.790 85.500 +/+
c
1440 x 900 55.935 59.887 106.500 -/+
c
1600 x 900RB 60.000 60.000 108.000 +/+
c
1680 x 1050 65.290 59.954 146.250 -/+
c
1920 x 1080 67.500 60.000 148.500 +/+
c
✎
NOTE
• The interlace mode is not supported.
• The set might operate abnormally if a non-standard video format is selected.
J5000-SQ_MI_BN68-08166K-00_L02.indb 20 2016-07-27 �� 1:31:58
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/