Yamaha DTX900 Инструкция по применению

Owner’s Manual

EN

2

DTX900 Owner’s Manual

PLEASE KEEP THIS MANUAL

This product utilizes batteries or an external power supply (adapter). DO

NOT connect this product to any power supply or adapter other than one

described in the manual, on the name plate, or speciﬁcally recom-

mended by Yamaha.

WARNING:

Do not place this product in a position where anyone could

walk on, trip over ,or roll anything over power or connecting cords of any

kind. The use of an extension cord is not recommended! If you must use

an extension cord, the minimum wire size for a 25’ cord (or less ) is 18

AWG. NOTE: The smaller the AWG number ,the larger the current han-

dling capacity. For longer extension cords, consult a local electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that accom-

pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at the

time of printing. However, Yamaha reserves the right to change or modify

any of the speciﬁcations without notice or obligation to update existing

units.

This product, either alone or in combination with an ampliﬁer and head-

phones or speaker/s, may be capable of producing sound levels that

could cause permanent hearing loss. DO NOT operate for long periods

of time at a high volume level or at a level that is uncomfortable. If you

experience any hearing loss or ringing in the ears, you should consult an

audiologist.

IMPORTANT: The louder the sound, the shorter the time period before

damage occurs.

Some Yamaha products may have benches and / or accessory mounting

ﬁxtures that are either supplied with the product or as optional accesso-

ries. Some of these items are designed to be dealer assembled or

installed. Please make sure that benches are stable and any optional ﬁx-

tures (where applicable) are well secured BEFORE using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how a

function or effect works (when the unit is operating as designed) are not

covered by the manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and consult your dealer

before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and environ-

mentally friendly. We sincerely believe that our products and the produc-

tion methods used to produce them, meet these goals. In keeping with

both the letter and the spirit of the law, we want you to be aware of the

following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of bat-

tery is approximately ﬁve years. When replacement becomes necessary,

contact a qualiﬁed service representative to perform the replacement.

This product may also use “household” type batteries. Some of these

may be rechargeable. Make sure that the battery being charged is a

rechargeable type and that the charger is intended for the battery being

charged.

When installing batteries, do not mix batteries with new, or with batteries

of a different type. Batteries MUST be installed correctly. Mismatches or

incorrect installation may result in overheating and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all batter-

ies away from children. Dispose of used batteries promptly and as regu-

lated by the laws in your area. Note: Check with any retailer of

household type batteries in your area for battery disposal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some reason

its useful life is considered to be at an end, please observe all local,

state, and federal regulations that relate to the disposal of products that

contain lead, batteries, plastics, etc. If your dealer is unable to assist

you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model num-

ber, serial number, power requirements, etc., are located on this plate.

You should record the model number, serial number, and the date of pur-

chase in the spaces provided below and retain this manual as a perma-

nent record of your purchase.

Model

Serial No.

Purchase Date

SPECIAL MESSAGE SECTION

92-BP

(bottom)

DTX900 Owner’s Manual

3

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT:

When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE:

This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : DRUM TRIGGER MODULE

Model Name : DTX900

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference

that may cause undesired operation.

See user manual instructions if interference to radio reception is sus-

pected.

(FCC DoC)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured makings identifying the

terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth termi-

nal of the three pin plug.

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be

mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national

legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health

and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the

point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the

correct method of disposal.

OBSERVERA!

Apparaten kopplas inte ur växelströmskällan (nätet) så länge som den ar ansluten till vägguttaget,

även om själva apparaten har stängts av.

ADVARSEL:

Netspændingen til dette apparat er IKKE afbrudt, sålæenge netledningen siddr i en

stikkontakt, som er t endt — også selvom der or slukket på apparatets afbryder.

VAROITUS:

Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta.

(standby)

• This applies only to products distributed by

Yamaha Music U.K. Ltd.

(2 wires)

4

DTX900 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or

radiators, and do not excessively bend or otherwise damage the

cord, place heavy objects on it, or place it in a position where

anyone could walk on, trip over, or roll anything over it.

• Only use the voltage speciﬁed as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

• Use the speciﬁed adaptor (page 155) only. Using the wrong adaptor

can result in damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it.

• This instrument contains no user-serviceable parts. Do not open the

instrument or attempt to disassemble or modify the internal

components in any way. If it should appear to be malfunctioning,

discontinue use immediately and have it inspected by qualiﬁed

Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or

wet conditions, or place containers on it containing liquids which

might spill into any openings. If any liquid such as water seeps into

the instrument, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the instrument inspected

by qualiﬁed Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

• When one of the following problems occur, immediately turn off the

power switch and disconnect the electric plug from the outlet. Then

have the device inspected by Yamaha service personnel.

• The power cord or plug becomes frayed or damaged.

• It emits unusual smells or smoke.

• Some object has been dropped into the instrument.

• There is a sudden loss of sound during use of the instrument.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a

multiple-connector. Doing so can result in lower sound quality, or

possibly cause overheating in the outlet.

• When removing the electric plug from the instrument or an outlet,

always hold the plug itself and not the cord. Pulling by the cord can

damage it.

• Remove the electric plug from the outlet when the instrument is not

to be used for extended periods of time, or during electrical storms.

• Do not place the instrument in an unstable position where it might

accidentally fall over.

• Before moving the instrument, remove all connected cables.

• When setting up the product, make sure that the AC outlet you are

using is easily accessible. If some trouble or malfunction occurs,

immediately turn off the power switch and disconnect the plug from

the outlet. Even when the power switch is turned off, electricity is

still ﬂowing to the product at the minimum level. When you are not

using the product for a long time, make sure to unplug the power

cord from the wall AC outlet.

• Use only the stand/rack speciﬁed for the instrument. When attaching

the stand or rack, use the provided screws only. Failure to do so

could cause damage to the internal components or result in the

instrument falling over.

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/AC power adaptor

Location

(7)-1

1/2

DTX900 Owner’s Manual

5

• Before connecting the instrument to other electronic components,

turn off the power for all components. Before turning the power on

or off for all components, set all volume levels to minimum.

• Be sure to set the volumes of all components at their minimum

levels and gradually raise the volume controls while playing the

instrument to set the desired listening level.

• Never insert or drop paper, metallic, or other objects into the gaps

on the panel.

• Do not rest your weight on, or place heavy objects on the

instrument, and do not use excessive force on the buttons, switches

or connectors.

• Do not use the instrument/device or headphones for a long period of

time at a high or uncomfortable volume level, since this can cause

permanent hearing loss. If you experience any hearing loss or

ringing in the ears, consult a physician.

Always turn the power off when the instrument is not in use.

Even when the power switch is in the “STANDBY” position, electricity is still ﬂowing to the instrument at the minimum level. When you are not using

the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

Connections Handling caution

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the instrument, or data that is lost or destroyed.

NOTICE

To avoid the possibility of damage to the product, data or other property, follow the notices below.

■

Handling and Maintenance

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the

instrument, TV, or radio may generate noise.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car

during the day) to prevent the possibility of panel disﬁguration or damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel or keyboard.

• When cleaning the instrument, use a soft, dry or slightly damp cloth. Do not use paint thinners, solvents, cleaning ﬂuids, or chemical-

impregnated wiping cloths.

■

Saving data

• DRAM data (page 76) is lost when you turn off the power to the instrument. Save the data to external USB storage device.

•To protect against data loss through media damage, we recommend that you save your important data onto two USB storage devices.

■

About the latest Firmware Version

Yamaha may from time to time update ﬁrmware of the product without notice for improvement. We recommend that you check our web site

for later releases and upgrade your ﬁrmware of the DTX900.

http://www.yamaha.co.jp/english/product/drums/ed/

Note that the explanations in this Owner’s Manual apply to the version of ﬁrmware when this Owner’s Manual was produced. For details about

functions added in later releases, refer to the above website.

■

About the pads

This Owner’s Manual described the model names of the drum pads which can be connected to the DTX900. Note that these were the latest

models at the time this Owner’s Manual was produced. For details about more recently released models, refer to the following website.

http://www.yamaha.co.jp/english/product/drums/ed/

(7)-2

2/2

6

DTX900 Owner’s Manual

Introduction

Thank you for purchasing the YAMAHA DTX900.

The new DTX900 incorporates the highly acclaimed AWM2 tone generator

and a sophisticated music sequencer.

In addition to the functions of its predecessor, DTX900 provides full support of the current

Yamaha trigger products and also sports a USB terminal for MIDI connections (in addition to conventional MIDI

connectors) — and has a built-in sampling feature that allows you to create your own Drum Voices.

The instrument is ideal for virtually any application — live performance, rhythm training, music creation and

studio recording. To get the most out of your DTX900, please read this manual carefully. After reading through

the manual, make sure to store it in a safe place so that you can refer back to it again as needed.

Included Accessories

●

AC Power Adaptor

●

Module stand

●

Module stand fastening screws (4; included)

●

Owner’s Manual (this document)

●

Data List

●

DVD-ROM* (containing software)

* For details on the bundled DVD-ROM, see page 159.

Information

■

About copyrights

• Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited

except for your personal use.

• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which

it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style ﬁles,

MIDI ﬁles, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of per-

sonal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE

OR USE ILLEGAL COPIES.

■

About functions/data bundled with the instrument

• This device is capable of using various types/formats of music data by optimizing them to the proper format music data for use with

the device in advance. As a result, this device may not play them back precisely as their producers or composers originally intended.

■

About this manual

• The contents of this Owner’s Manual and the copyrights thereof are under exclusive ownership by Yamaha Corporation.

• The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat different

from those on your instrument.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

DTX900 Owner’s Manual

7

Main Features

Designed primarily for professional drummers, the DTX900 has a Drum Trigger feature, a 64-note polyphonic Tone Gener-

ator, a built-in Sampling feature that lets you expand the available sounds, a high-performance Metronome (Click) feature and

a built-in music sequencer that enables recording and playback of rhythm or accompaniment patterns, and even lets you create

an entire Song. The DTX900 is an exceptionally versatile instrument that can be used in a variety of situations such as live

performance, personal practice, and much more.

■

Drum Trigger

• The DTX900 drum trigger module is compatible with the

new pads (XP series.)

• Built into the unit are 15 Trigger Input jacks and a Hi-Hat

Controller jack.

• The instrument also features jacks that are compatible with

two-zone or three-zone pads (pads that transmit different

signals depending on the area that is hit). Moreover, the

snare drum jack is compatible with pad-controller-equipped

pads. This lets you adjust the ‘virtual’ snares and the tun-

ing—just as you would with a snare drum. All in all, the

DTX900 offers virtually the same playability, expressive-

ness and functionality that you get in an acoustic drum kit.

• By combining the Stack function, which lets you play mul-

tiple voices (MIDI notes) at the same time, along with the

Alternate function, which lets you play a sequence of the

Stack program, you can create complex performances and

play passages in realtime that would otherwise be impossi-

ble on conventional acoustic drums.

■

Tone Generator

• The DTX900 is equipped with a high-quality, 16-bit AWM2

(PCM) tone generator with 64-voice polyphony that pro-

duces dynamic voices or exceptional realism.

• The instrument has a wide variety of Voices including

authentic acoustic drums, unique electronic percussion,

sound effects, and normal keyboard Voices. It can also be

used as a high-quality drum tone generator along with vari-

ous MIDI devices, even without using the Drum Pads.

• Also included in the unit are 50 preset Drum Kits which

contain natural, authentic sounding acoustic Drum Kits, and

cover a wide range of music genres, such as rock, funk,

jazz, reggae, Latin, etc. Moreover, User kit memory is avail-

able for storing 50 sets. With this, you can set up your own

original Drum Kits using the various Drum Voices.

• The Sampling feature lets you record the audio signal to the

DTX900 or load the audio ﬁle from the USB storage device

to create your original Voice. The created Voice can be

assigned to the Drum Kit as desired.

• The instrument is equipped with a Variation Effect which

can be used for each Drum Kit as well as Reverb, Chorus

and Master Effects which can be used for the entire

DTX900. In addition, an Insertion Effect for the sound input

via the AUX IN/SAMPLING IN jack is provided, allowing

you to adjust the quality of AUX IN/SAMPLING IN sound

or record an audio signal to which the Insertion Effect is

applied to the DTX900 in the Sampling mode.

■

Music Sequencer (Song)

• The built-in sequencer contains a wide variety of Preset

Songs. The Mute function lets you turn on/off the rhythm

(drum & percussion sound) part, bass part and other accom-

paniment part individually, or turn each track on/off.

• The DTX900 also allows you to record your performance in

real time and allows you to play along with the Song data

while muting the original drum part.

•Four Pad Songs can be individually controlled and simulta-

neously played by trigger input from the pads.

■

High-performance Metronome (Click)

• The DTX900 provides a comprehensive, multi-function

metronome, allowing various click settings such as voice

and tuning for each beat timing. Furthermore, you can

change the accent timing and use the Measure Break feature

that alternates click playback between on and off (mute)

repeatedly.

• The Groove Check Function checks and provides instant

feedback on your rhythmic skills—a powerful tool for

improving your technique. It includes a Rhythm Gate func-

tion that produces sounds only if your timing is accurate.

■

Chain

• Programming a Chain sequence lets you call up the Drum

Kit number, Song number and Click settings (tempo and

beat) in order during your live performance. Each step in

the programmed Chain can be called up by hitting the pad.

■

Interfaces

• The USB terminal and MIDI connectors on the rear panel

let you connect a computer and other MIDI devices to the

DTX900. These enable fast, efﬁcient and comprehensive

music-creation capabilities, letting you play sounds from an

external tone generator as well as record your own perfor-

mance using the included Cubase AI.

• Each of the six INDIVIDUAL OUTPUT jacks can sepa-

rately output any speciﬁed Drum Voice such as Snare and

Tom to send each instrument signal to an external mixer for

live performance or recording session. In addition, a Digital

Output (S/PDIF) terminal lets you transfer the DTX900 ste-

reo sounds to other devices with no noise and full digital

quality.

• The instrument has a built-in AUX IN/SAMPLING IN jack

which lets you connect a CD player to the DTX900—allow-

ing you to play the instrument along with CD playback as

well as use the powerful Sampling feature.

8

DTX900 Owner’s Manual

Contents

Introduction .............................................................6

Included Accessories ..............................................6

Main Features .........................................................7

Panel Controls..................................................... 10

Basic Operation................................................... 13

Setting Up ............................................................ 16

Connecting the Pads.............................................16

Setting Up the Power Supply ................................18

Turning the Power On...........................................18

Connecting to Speakers or Headphones..............19

Connecting to External Audio Equipment .............19

Connecting External MIDI Devices .......................20

Connecting a USB Storage Device.......................21

Selecting the Trigger Setup ..................................22

Connecting a Computer ........................................24

Setting up Cubase Remote Control ......................25

Creating a Song by Using a Computer .................26

Adjusting the Sound and Display Contrast ...........27

Quick Guide 28

How to Play the Drum Pads ............................... 28

Playing the DTX900............................................. 30

Hitting the Pads.....................................................30

Selecting a Drum Kit .............................................30

Adjusting the Volume by Using the Sliders...........31

Playing Along With the Click ............................. 32

Start the Click (Metronome) ..................................32

Changing the Tempo and Time Signature

(Beat) of the Click .................................................33

Tap Tempo ........................................................... 34

Playing Along With a Song ................................ 35

Song Playback ......................................................35

Adjusting the Volume of the Song

Accompaniment ....................................................38

Changing the Tempo of the Song .........................38

Song Part Mute Setting.........................................39

Creating a Drum Kit ............................................ 40

Recording Your Drum Performance to a Song

.. 43

Recording System.................................................43

Recording Methods...............................................43

Recording Your Drum Performance to a Song .....44

Recording Additional Notes to an

Already-recorded Track (Overdub) .......................46

Recording Along With the Preset Song ................46

Re-recording a Track After Clearing .....................48

Assigning a Name to a User Song........................49

Using the Groove Check Function.....................50

Setting the Check Timing ..................................... 50

Trying Out Groove Check..................................... 51

Trying Out Rhythm Gate....................................... 52

Saving the Created Data to a USB Storage

Device ...................................................................54

File/Folder Selection............................................. 54

Saving the Created Data to a USB Storage

Device................................................................... 55

Loading a File Saved to a USB Storage Device... 56

Reference 57

Basic Structure of the DTX900 ...........................57

The Functional Blocks .......................................... 57

Pads (Trigger Input Sources) and

Trigger Signals ..................................................... 58

Tone Generator Block (Drum Kits and

Drum Voices)........................................................ 62

Sampling............................................................... 65

Song ..................................................................... 67

Effects................................................................... 68

Internal Memory and File Management................ 76

Drum Kit Mode [DRUM KIT] ................................78

Basic Procedure in the Drum Kit Mode ................ 78

Selecting a Drum Kit [F1] PLAY ........................... 79

Setting Drum Voice Parameters [F2] VOICE........ 79

Programming the Stack/Alternate [F3] STK/ALT.. 86

Effect Settings [F4] EFFECT ................................ 89

Pad Settings [F5] PAD.......................................... 92

Other Settings [F6] OTHER.................................. 95

Song Mode [SONG] .............................................98

Song Play [F1] PLAY............................................ 98

Song Recording [F1] PLAY

→

[REC] ................... 98

Song Jobs [F2] JOB ............................................. 98

Click Mode [CLICK] ...........................................104

Basic Procedure in the Click Mode..................... 104

Basic Settings of the Click Sound [F1] PLAY ..... 105

Click Voice Settings [F2] VOICE ........................ 106

Tap Tempo Function [F3] TAP ........................... 106

Groove Check Function [F4] GROOVE.............. 106

Click Sound Settings [F5] OTHER...................... 107

Trigger Mode [TRIGGER] ..................................108

Basic Procedure in the Trigger Mode ................. 108

Selecting the Trigger Setup [F1] SELECT.......... 109

Selecting the Pad Type [F2] TYPE..................... 109

Trigger Sensitivity Settings [F3] SENS ............... 109

Setting the Rejection [F4] REJECT .................... 110

Other Settings [F5] OTHER................................ 111

Contents

DTX900 Owner’s Manual

9

File Mode [FILE] .................................................112

Terminology in the File Mode ............................. 112

File Types Compatible With the DTX900 ........... 113

Saving a File [F1] SAVE ..................................... 114

Loading a File [F2] LOAD ................................... 116

Changing the Name of a File or Directory

[F3] RENAME ..................................................... 121

Deleting a File or Directory [F4] DELETE........... 122

Formatting USB Storage Media [F5] FORMAT .. 123

Utility Mode [UTILITY]........................................124

Basic Procedure in the Utility Mode.................... 124

General Settings [F1] GENERAL ....................... 124

Pad Settings [F2] PAD........................................ 126

Effect Settings [F3] EFFECT .............................. 127

External Audio Settings [F4] AUXIN ................... 128

MIDI Settings [F5] MIDI ...................................... 130

Resetting the User Memory to the Initial

Factory Settings [F6] FACTSET ......................... 131

Chain Mode [CHAIN]..........................................132

Using a Programmed Chain [F1] SELECT ......... 132

Programming a Chain [F2] EDIT ........................ 133

Naming the Created Chain [F3] NAME .............. 134

Sampling Mode [SAMPLING] ............................135

Sampling Setup .................................................. 135

Sampling Operation and User Voice Assignment

[F1] SELECT/[F2] SETTING............................... 136

Trimming a User Voice [F3] TRIM ...................... 139

Sampling Jobs [F4] JOB..................................... 142

Appendix 147

Optional DIMM Installation................................147

Troubleshooting.................................................150

Display Messages ..............................................153

Specifications.....................................................155

Index....................................................................156

About the Accessory Disk.................................159

SOFTWARE LICENSE AGREEMENT................159

10

DTX900 Owner’s Manual

Panel Controls

■

Front Panel

q

LCD display

The large LCD Display shows information and data needed to

operate the DTX900.

w

LED display

The LED display indicates the current Drum Kit or tempo value

in three digits.

e

[DRUM KIT] button

Pressing this button enters the Drum Kit mode, allowing you to

select the desired Drum Kit (pages 30 and 78).

r

[CLICK] button

Pressing this button enters the Click mode, allowing you to per-

form the Click (Metronome) setup (pages 32 and 104).

t

[FILE] button

Pressing this button enters the File mode, allowing you to man-

age data created in each of the modes (pages 54 and 112).

y

[CHAIN] button

Pressing this button enters the Chain mode, allowing you to

program a Chain, which is a series of Drum Kits and Songs

arranged in the order you want (page 132).

u

[SONG] button

Pressing this button enters the Song mode, allowing you to

play an existing Song or record your drum performance (pages

35 and 98).

i [TRIGGER] button

Pressing this button enters the Trigger mode, allowing you to

select or program a Trigger Setup (pages 22 and 108).

o [UTILITY] button

Pressing this button enters the Utility mode, allowing you to set

parameters related to the entire system of the DTX900 (page

124).

!0 [SAMPLING] button

Pressing this button enters the Sampling mode, allowing you to

record the external audio signal then create User Voices (page

135).

888

w

e u

r i

t o

y !0

!1

!2

!3

!6

!7 !8 !9

@0 @1 @2 @3 @4 @5

@7 @8

#0 #1

@6

@9

!4

q

!5

NOTE

• Before use, be sure to remove the transparent ﬁlm applied to the LCD

display to protect it during transportation.

NOTE

• Before use, be sure to remove the transparent ﬁlm applied to the LED

display to protect it during transportation.

Panel Controls

DTX900 Owner’s Manual

11

!1

TRIGGER INDICATOR

This lamp indicates whether or not the DTX900 receives the

trigger signal via the Trigger Input jacks. The lamp is turned on

when receiving the trigger signal. This lamp is turned on also

when pressing the Audition button (described below).

!2 Audition button

You can use this button instead of the drum pad. Pressing this

button is equivalent to receiving a signal from the currently

selected trigger input source (page 58). When turning the

power on, pressing this button is equivalent to striking the head

of the snare pad (the pad connected to the SNARE jack).

!3 [F1] – [F6] (Function) buttons

These buttons located directly below the LCD display call up

the corresponding functions indicated in the display. In the dis-

play hierarchy, these functions [F] rank just below the modes.

!4 [SF1] – [SF6] (Sub-Function) buttons

These buttons located directly below the LCD display call up

the corresponding sub functions indicated in the display. In the

display hierarchy, these sub functions [SF] rank just below the

functions [F].

!5 Transport buttons (page 35)

These buttons control recording and playback of the Song

sequence data.

pp

(Top) button

Instantly returns to the beginning of the current Song (i.e.,

the ﬁrst beat of the ﬁrst measure).

rr

(Reverse) button

Press brieﬂy to move back one measure at a time, or hold

to continuously rewind.

ff

(Forward) button

Press brieﬂy to move forward one measure at a time, or

hold to continuously fast-forward.

REC (Record) button

Press this to enable Song recording. (The indicator lights.)

>>

/■ (Play/Stop) button

Press to start/stop recording or playback. Pressing this but-

ton during playback stops playback at the current point in

the Song then pressing this again starts playback from that

point. During recording and playback, the indicator lights.

CLICK ON/OFF button

Press this button to start/stop the metronome (click sound).

!6 MASTER slider (page 31)

Adjusts the output volume of the stereo mix from the OUTPUT

L/MONO and R jacks.

!7 PHONES slider (page 31)

Adjusts the output volume of the stereo-mixed sounds for the

PHONES jack. This is independent from the MASTER slider

setting.

!8 CLICK slider (page 31)

Adjusts the output volume of the click sound.

!9 ACCOMP slider (page 31)

Adjusts the output volume of the accompaniment parts (those

other than MIDI channel 10) in the Song.

@0 KICK slider (page 31)

Adjusts the volume of the bass drum.

@1 SNARE slider (page 31)

Adjusts the volume of the snare drum.

@2 TOM slider (page 31)

Adjusts the volume of the toms.

@3 CYMBAL slider (page 31)

Adjusts the volume of the cymbals.

@4 HI-HAT slider (page 31)

Adjusts the volume of the hi-hat cymbals.

@5 MISC slider (page 31)

Adjusts the volume of miscellaneous rhythm or percussion

sounds – other than snare and bass drums, toms, hi-hats, and

ride and crash cymbals.

@6 Data dial

For editing the currently selected parameter. To increase the

value, turn the dial right (clockwise); to decrease the value, turn

the dial left (counter-clockwise). If a parameter with a wide

value range is selected, you can change the value in broader

strokes by quickly turning the dial.

@7 [DEC/NO] button (page 13)

For decreasing the value of the currently selected parameter.

Also use it to cancel a Job or a Store operation.

@8 [INC/YES] button (page 13)

For increasing the value of the currently selected parameter.

Also use it to actually execute a Job or a Store operation.

@9 Cursor buttons (page 13)

The cursor buttons move the “cursor” around the LCD display

screen, highlighting and selecting the various parameters.

#0 [EXIT] button

Press this button to cancel an operation when a conﬁrmation

message is shown in the LCD. This button can be used also

when the drum sound continues inadvertently or unexpectedly

and you want to stop it.

#1 [ENTER/STORE] button

As with the ENTER button, press this to enter the display of the

selected Song Job/Sampling Job, for example.

As with the STORE button, press this to store the edited data in

the Drum Kit mode, Click mode, Trigger mode, Utility mode,

and Chain mode.

You can also use this button when executing the Song Job or

Sampling Job.

Panel Controls

12

DTX900 Owner’s Manual

■ Rear Panel

q F (Standby/On) switch

Press to turn the power ON or OFF.

w DC IN terminal

Connect the AC power adaptor to this terminal.

e Cable clip

Wrap the DC output cable of the adaptor around the cable clip

to prevent accidental unplugging of the cable during operation.

r LCD Contrast Control

Use this control to set the LCD display for optimum legibility.

t GAIN knob

For adjusting the input gain of the audio at the AUX IN/SAM-

PLING IN jack. Depending on the connected device (micro-

phone, CD player, etc.), you may need to adjust this for

optimum level. Increase the gain by rotating the knob clock-

wise, and decrease it by rotating the knob counter-clockwise.

y AUX IN/SAMPLING IN jack

External audio signals can be input via this phone jack (stan-

dard stereo phone plug). This is convenient for playing along

with music from a CD player or other device. In the Sampling

mode, this jack is used for capturing audio data as User Voices.

u OUTPUT L/MONO and R jacks

External audio signals can be input via these phone jacks (1/4"

mono phone plug). Various devices such as microphone, gui-

tar, bass, CD player, can be connected to these jacks. For ste-

reo signals (such as from audio equipment), use both jacks.

For mono signals (such as from a microphone or guitar), use

only the L jack.

i PHONES jack

For connection to a pair of stereo headphones.

o INDIVIDUAL OUTPUT 1 – 6 jacks

Line level audio signals are output from this instrument via

these phone jacks (1/4" mono phone plug). These outputs are

independent of the main output (at the L/MONO and R jacks),

and can be freely assigned to any Drum Voice. This lets you

route speciﬁc sounds for processing with a favorite outboard

effect unit.

!0 DIGITAL OUT connector

This is for connecting to a coaxial digital input (S/P DIF) on an

external audio device. This jack digitally outputs stereo audio

signals identical to those from the OUTPUT L/MONO and R

jacks, but is not affected by the !6 MASTER volume slider set-

ting (the digital jack always outputs audio signals at the maxi-

mum volume level).

!1 MIDI IN/OUT connectors

These jacks are for the transfer of MIDI data to and from exter-

nal MIDI devices.

!2 USB terminals

This instrument is equipped with two types of USB terminals on

the rear panel – USB TO HOST and USB TO DEVICE. The

USB TO HOST terminal is used to connect this instrument to

the computer via the USB cable. The USB connection between

the instrument and the computer can only be used for transfer

of MIDI data. No audio data can be transferred via USB. The

USB TO DEVICE terminal is used to connect this instrument to

a USB storage device (ﬂash memory, hard disk drive, etc.) via

the USB cable. This lets you save the data created on this

instrument to an external USB storage device as well as load

data from the device to the instrument. Save/Load operations

can be performed in the File mode.

!3 HI-HAT CONTROL jack

This jack is used to connect a hi-hat controller. Depending on

the setting on the Drum Kit mode (page 78), you can transmit

the MIDI messages such as Control Change by using the Hi-

Hat Controller.

!4 Trigger Input jacks (q SNARE – o HI-HAT)

These jacks, which are compatible with stereo pads (two-zone

and three-zone pads) as well as mono pads, receive the Trigger

Signal transmitted from the drum pads. Furthermore, the q

SNARE – t TOM4 jacks are also compatible with the Pad

Controller (page 59).

!5 Trigger Input jack (!0/!1 KICK)

This jack is designed to accept two separate trigger signals

from two mono (single) pad by using a Y-shaped cable (stereo

phone plug for this jack and two mono plugs for the two pads).

When using the KP125W/KP65 equipped with the PAD INPUT

jack, the Trigger Signals of another pad connected to the PAD

INPUT jack and KP itself can be transferred via a single stereo

cable (no need for a Y-shaped cable) to the DTX900. In this

case, the stereo cable is plugged into the OUTPUT jack of a

pad and this Trigger Input jack.

!6 Trigger Input jacks (!2 – !5)

These jacks, which are compatible with stereo pads (two-zone

and three-zone pads) as well as mono pads, receive the Trigger

Signal transmitted from the drum pads.

wq

e

t

y

u

i

r

o

!0

!1

!2

!5

!3

!6 !4

DTX900 Owner’s Manual

13

Basic Operation

Use these four buttons to navigate through the display,

moving the cursor around the various selectable items and

parameters in the screen. When selected, the relevant item

is highlighted (the cursor appears as a dark block with

inverse characters). You can change the value of the item

(parameter) at which the cursor is located by using the data

dial, [INC/YES] and [DEC/NO] buttons.

Rotating the data dial to the right (clockwise) increases the

value, while rotating it to the left (counter-clockwise)

decreases it. For parameters with large value ranges, you

can increase the value by 10 by simultaneously holding

down the [INC/YES] button and pressing the [DEC/NO]

button. To decrease by 10, do the opposite; simultaneously

hold down the [DEC/NO] button and press the [INC/YES]

button.

Each mode described above contains various displays, with

various functions and parameters. To navigate your way

through these displays and select a desired function, use the

[F1] – [F6] buttons and the [SF1] – [SF6] buttons. When

you select a mode, the available displays or menus appear

directly above the buttons at the bottom of the display (as

shown below).

Depending on the currently selected mode, up to six func-

tions are available and can be called up with the [F1] – [F6]

buttons. Keep in mind that the available functions differ

depending on the selected mode.

Depending on the currently selected mode, up to six func-

tions (sub-functions) are also available and can be called up

with the [SF1] – [SF6] buttons. Keep in mind that the avail-

able functions differ depending on the selected mode.

(Some displays may not have any sub-functions for these

buttons.)

Moving the Cursor

Changing or Editing Parameter Values

IncreaseDecrease

Increase

by 1

Decrease

by 1

Functions and Sub-Functions

These functions can be selected

via the corresponding button

([F1] – [F6]).

These functions can be selected

via the corresponding button

([SF1] – [SF6]).

Basic Operation

14

DTX900 Owner’s Manual

In order to make operation of the DTX900 as comprehen-

sive and as smooth as possible, all functions and operations

have been grouped in “modes.” To enter the desired mode,

press the corresponding Mode button.

The function of each mode is as follows:

You can adjust or set various parameters by using the data

dial, [INC/YES] button and [DEC/NO] button in each

mode. When changing the value of the parameter in these

modes, the [E] (Edit Indicator) will appear on the top left

corner of the LCD display. This indicates that the current

program (Drum Kit, etc.) has been modiﬁed but not yet

stored. If you wish to store the status or sound obtained by

editing, be sure to store the current program to internal

User memory by pressing the [ENTER/STORE] button

before selecting another program.

For parameters having large value ranges, you can also

enter the value directly, using the buttons below the LCD

display as a numeric keypad. When the cursor is located on

such a parameter, the [NUM] icon appears at the lower

right corner of the LCD display. When the [SF6] NUM but-

ton is pressed in this status, each digit (1 – 9, 0) is assigned

to the [SF1] – [SF5] and [F1] – [F5] buttons as shown

below, allowing you to input a number directly by using

these buttons.

After completing the number input, press the [ENTER/

STORE] button to actually enter the number.

Note that the cursor highlight can be moved to the currently

edited number by pressing the [F6] CURSOR button, and

then moved from digit to digit by using the Cursor [N] and

[M] buttons. This method is useful when you want to

directly change only one speciﬁc digit. The cursor disap-

pears when pressing the [F6] button again.

Modes

Mode Function Page

Drum Kit Selecting/editing a Drum Kit. 78

Click

Setting the Click (Metronome) related

parameters and performing the Groove

Check function.

104

File Managing ﬁles and directories (folders). 112

Chain Programming a Chain sequence. 132

Song Selecting/recording a Song. 98

Tr igger Selecting/editing a Trigger Setup. 108

Utility Setting the system related parameters. 124

Sampling

Recording audio signals to create a User

Voice.

135

Edit Indicator

If the Edit Indicator appears...

Inputting a Number Directly

Numeric

Keypad

Basic Operation

DTX900 Owner’s Manual

15

As shown below, you can set the name by repeating the two

operations – moving the cursor to the desired location by

using the Cursor buttons and then selecting a character by

using the data dial, [INC/YES] button, and [DEC/NO] but-

ton.

■ Using the character list

If you ﬁnd it difﬁcult to select the desired characters with

the above method, you may want to use the following

method – selecting the characters directly from a list.

Inputting Characters (Naming, etc.)

Move the cursor to the desired location in the name

Select a character at the cursor location

When the cursor is located at the Name, this [LIST]

icon appears and you can call up the Character List

display by holding the [SF6] button. Release the

[SF6] button to return back to the original display.

Perform the operations below while holding the [SF6] button.

Move the cursor to the desired location.

Select a character for the cursor location in the name.

16

DTX900 Owner’s Manual

Setting Up

Connecting the Pads

Referring to the illustration below, connect the output cable from each pad to each Trigger Input jack located on the rear

panel of the DTX900. All Trigger Input jacks are conveniently labeled (1 SNARE, etc.), so make sure each pad is connected

to its corresponding Trigger Input jack.

■ DTX900K

IMPORTANT

You’ll need to change the Trigger Settings of the DTX900 according to the type of drum set you are using (Stan-

dard Set/Special Set/Acoustic Drums, etc.). If the setting is not appropriate, problems may occur—such as

improper sound, or inappropriate volume balance among the pads. Refer to the “Selecting the Trigger Setup”

section on page 22 on how to select the appropriate setup.

•To prevent electric shock and damage to the devices, make sure the power is switched OFF on the DTX900 and all

related devices before making any connections to the DTX900’s input and output jacks.

WARNING

PCY135

DTX900

PCY155

PCY135

KP125W

XP120SD

RHH135

XP100T XP100T

XP100T

Attaching the module stand

Attach the included module stand to the

DTX900 using the module stand fastening

screws.

* Be sure to use the included screws.

to 1SNARE

to JKICK/K

to 2TOM1 to 3TOM2

to 4TOM3

to HI-HAT

CONTROL

to 9HI-HAT

to 7CRASH

to 6RIDE

DTX900

Module stand

(included)

Module stand fastening

screws x 4 (included)

* First, connect the RHH135’s

[PAD] output jack to the 9HI-

HAT jack on the DTX900,

then connect the RHH135’s

[HI-HAT CONTROL] output

jack to the HI-HAT CON-

TROL jack on the DTX900.

*Foot pedal is not included

in the Standard Set.

NOTE

• The pad models described in the illustrations were

included in the Standard Set/Special Set at the moment

this Owner’s Manual was produced. Keep in mind that the

model names of your Standard Set or Special Set may be

different from the ones illustrated here. For details about

the latest information on Yamaha drum pads, refer to the

following website.

http://www.yamaha.co.jp/english/product/drums/ed/

to 8CRASH2

Setting Up

DTX900 Owner’s Manual

17

■ DTX950K

■ Setting up with Acoustic Drums

The DTX900 can be played from an acoustic drum kit if the kit is ﬁtted with an optional set of drum triggers (such as

Yamaha DT20 Drum Triggers) and the triggers are properly connected to the input jacks of the DTX900.

PCY135

DTX900

PCY155

KP125W

XP120SD

RHH135

XP100T XP100T

XP120T

Attaching the module stand

Attach the included module stand to the

DTX900 using the module stand fastening

screws.

* Be sure to use the included screws.

DTX900

Module stand

(included)

Module stand fastening

screws x 4 (included)

to 1SNARE

to JKICK/K

*Foot pedal is not included

in the Special Set.

to 9HI-HAT

to HI-HAT

CONTROL

to 7CRASH1

to 2TOM1 to 3TOM2

to 5TOM4

to 4TOM3

to 6RIDE

to 8CRASH2

* First, connect the RHH135’s

[PAD] output jack to the 9HI-

HAT jack on the DTX900, then

connect the RHH135’s [HI-HAT

CONTROL] output jack to the

HI-HAT CONTROL jack on the

DTX900.

Setting Up

18

DTX900 Owner’s Manual

Setting Up the Power Supply

1

Make sure that the F (Standby/On) switch

of the instrument is set to standby ( ).

2

Connect the DC plug of the included AC

power adaptor to the DC IN jack on the

rear panel. To prevent the cord from being

unplugged accidentally, wrap the cord

around the cable clip and secure it.

3

Connect the other end of the power cord

to an AC outlet.

Turning the Power On

After you’ve made all necessary connections (trigger,

audio, MIDI), turn down all volume controls of the

DTX900 and other audio equipment.

Turn the power on ( ) by pressing the F (Standby/On)

switch on the rear panel of the DTX900, then turn on the

power of the ampliﬁers.

■ Connecting a mixer or other MIDI

devices

Make sure that all volume settings are turned down all the

way to the minimum. Then turn on the every device in your

setup in the order of MIDI masters (controllers), MIDI

slaves (receivers), then audio equipment (mixers, ampliﬁ-

ers, speakers, etc.).

• Make sure that the power adaptor’s cord is not bent at an extreme

angle when wrapping the cord around the clip. Doing this can dam-

age or sever the cord and create a ﬁre hazard.

• Use only the included power adaptor or an equivalent recom-

mended by Yamaha. The use of any other adaptors may cause

irregular operation or damage to the device.

• Only use the voltage speciﬁed as correct for the DTX900.

•Even when the instrument is turned off, electricity is still ﬂowing to

the instrument at the minimum level. When you are not using the

DTX900 for a long time, make sure to unplug the AC power adap-

tor from the wall AC outlet.

CAUTION

WARNING

NOTE

• When powering down the setup, ﬁrst turn down the volume for each audio

devices, then switch off each device in the reverse order (ﬁrst audio equip-

ment, then MIDI).

888

1 DTX900

(transmitting device)

2 MIDI slave

3 External audio equipment

(mixer → ampliﬁer)

Setting Up

DTX900 Owner’s Manual

19

Connecting to Speakers or

Headphones

Since the DTX900 has no built-in speakers, you’ll need an

external audio system or a set of stereo headphones to

properly monitor it.

■ OUTPUT L/MONO, R jacks (standard

mono phone)

These jacks allow you to connect the DTX900 to an exter-

nal ampliﬁer/speaker system and produce full, ampliﬁed

sound.

• Use the DTX900’s OUTPUT L/MONO jack when

connecting to a device with a mono input.

■ PHONES jack (standard stereo phone

jack)

The overall headphone level is adjusted by the PHONES

slider.

Connecting to External Audio

Equipment

When recording your performance on a DTX900 Drum Kit

or sending its sounds to a mixer, connect your equipment as

follows:

The OUTPUT (L/MONO and R) and INDIVIDUAL OUT-

PUT (1 to 6) jacks produce line level audio signals regard-

less of whether headphones are connected or not. These

jacks are mono phone type. To make audio connections via

these jacks, use cables with a mono phone plug for the

DTX900 and an appropriate plug for the other device.

Use both OUTPUT jacks (L/MONO and R) for stereo out-

put. If the other device has a mono input, use the L/MONO

jack only.

The DIGITAL OUTPUT connector can be connected to a

coaxial digital input (S/P DIF) on an external audio device.

This connector digitally outputs stereo audio signals identi-

cal to those from the OUTPUT L/MONO and R jacks.

External audio signals input to AUX IN/SAMPLING IN

jack can be monitored together with the DTX900 sounds

via headphones connected to the PHONES jack, and can be

recorded to create additional User Voices. If necessary, you

can use the [GAIN] knob on the rear panel to adjust the

gain of the input signal.

• Whenever making connections, make sure that the plug on the cable

being used corresponds to the type of jack on the device.

• Do not use the DTX900 at a high volume level for a long period of time,

or your hearing may be damaged. Doing so may cause hearing loss.

Headphones

Monitor system for the DTX series

MS100DR, MS50DR, etc.

OUTPUT L/MONO, R

PHONES

NOTICE

CAUTION

NOTE

• Connect a set of headphones to the PHONES jack for monitoring the ste-

reo output (identical to that of the OUTPUT jacks). The sounds output from

the INDIVIDUAL OUTPUT jacks cannot be heard from the headphones

connected to the PHONES jack.

• Depending on the connected equipment, you may need to change the

parameter settings in the Utility mode. For details, see page 128.

INDIVIDUAL

OUTPUT

DIGITAL OUT

DIGITAL IN

AUX OUT

LINE OUT

AUX IN

O1V96

SOLO SOLO

ON ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ON

SOLO

ONON

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

PEAK

SIGNAL

1-16 17-32 MASTER REMOTE

LAYER

SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SELSEL

ST IN

ENTER

EQUALIZER

HIGH

HIGH-MID

LOW-MID

LOW

Q

FREQUENCY

GAIN

STEREO

SELECTED CHANNEL

PAN

DEC INC

SOLO CLEAR

RECALL

STORE

SCENE MEMORY

PHONES

MONITOR

OUT

MONITOR

2TR IN

CH15

/

16

2TR IN

LEVEL

PHONES

LEVEL

0

10

0

10

+4

-26

GAIN

+4

-26

GAIN

+4

-26

GAIN

+4

-26

GAIN

20dB

-16 -60

GAIN

20dB

-16 -60

GAIN

20dB20dB20dB20dB20dB20dB20dB20dB20dB20dB

-16 -60

GAIN

-16 -60

GAIN

-16 -60

GAIN

-16 -60

GAIN

-16 -60

GAIN

-16 -60

GAIN

-16 -60

GAIN

-16 -60

GAIN

-16 -60

GAIN

-16 -60

PAD

FADER MODE

DISPLAY ACCESS

AUX 1

AUX 1 AUX 2 AUX 3 AUX 4 AUX 5 AUX 6 AUX 7 AUX 8 BUS 1 BUS 2 BUS 3 BUS 4 BUS 5 BUS 6 BUS 7 BUS 8

AUX 2 AUX 3 AUX 4

AUX 8AUX 7AUX 6AUX 5

HOME (METER)

DYNAMICS

EQ EFFECT VIEW

PATCH

UTILITYMIDISCENE

DIO/SETUP

/ INSERT/

DELAY

PAN/

ROUTING

PAIR/

GROUP

A

B

A

B

A

B

A

B

A

B

A

B

A

B

A

B

A

B

A

B

A

B

A

B

16

1513

121110987643215

14

INSERT I

/

OINSERT I

/

OINSERT I

/

OINSERT I

/

OINSERT I

/

OINSERT I

/

OINSERT I

/

OINSERT I

/

OINSERT I

/

OINSERT I

/

OINSERT I

/

OINSERT I

/

O

L

R

IN OUT

2TR

-10dBV (UNBAL)

PHANTOM +48V

CH9-12CH5-8CH1-4

INPUT

(BAL)

INSERT

OUTIN

(UNBAL)

ST IN 1 ST IN 2

USER DEFINED

KEYS

12

34

56

78

55

5

+10

5

1010

10

1515

15

2020

20

303030

30

4040

40

5050

50

6060

7070

20

30

40

50

60

70

00

5

10

15

20

0

5

+10

5

10

15

30

20

30

40

50

60

70

20

30

40

50

60

70

20

30

40

50

60

70

20

30

40

50

60

70

20

30

40

50

60

70

15

0

5

10

15

20

0

5

+10

5

10

0

30

15

5

10

15

20

0

5

+10

5

10

0

30

15

5

10

15

20

0

5

+10

5

10

0

30

15

5

10

15

20

0

5

+10

5

10

0

30

15

20

30

40

50

60

70

30

15

20

30

40

20

30

40

20

30

40

20

30

40

50

50505050

20

30

40

50

20

30

40

50

60

70

40

50

60

70

40

50

60

70

40

50

60

70

40

50

60

70

40

50

60

70

40

50

60

70

40

50

60

70

30

15

5

10

15

20

0

5

+10

5

10

0

5

10

15

20

0

5

+10

5

10

0

5

10

15

20

0

30

5

10

15

20

0

30

5

10

15

20

0

30

5

10

15

20

0

30

5

10

15

20

0

303030

5

10

15

20

0

5

10

15

20

0

5

10

15

20

0

5

+10

5

10

0

15

5

+10

5

10

0

15

5

+10

5

10

0

15

5

+10

5

10

0

15

20

30

40

50

15 15

20

30

40

50

15

5

+10

5

10

0

5

+10

5

10

0

5

+10

5

10

0

5

+10

5

10

0

123456

7

891011 12

7

891011 12

13 14 15 16

32313029282726252423222120191817

STEREO

13 14 15 16

OVER

0

-3

-6

-9

-12

-15

-18

-24

-30

-36

-48

888

CD player

MD player

DTX900

Setting Up

20

DTX900 Owner’s Manual

Connecting External MIDI Devices

Using a standard MIDI cable (available separately), you can connect an external MIDI device, and control it from the

DTX900.

This connection lets you sound an external MIDI tone generator (synthesizer, tone generator module, etc.) by playing the

DTX900 or playing back a Song on the DTX900. Also, an external sequencer can be used to drive the DTX900’s Tone Gen-

erator. Furthermore, the use of MIDI functions allows for an even greater range of performance and recording possibilities

with the DTX900.

■ Controlling an external tone generator or synthesizer

Use a MIDI cable to connect the MIDI OUT connector on the DTX900 with the MIDI IN connector on the external MIDI

device.

■ Controlling from an external MIDI keyboard or synthesizer

Use a MIDI cable to connect the MIDI IN connector on the DTX900 with the MIDI OUT connector on the external MIDI

device.

NOTE

•Any one of the DTX900 interfaces (MIDI connectors or the USB terminal) can be used for MIDI data transmission/

reception. However, they cannot be used at the same time. Select which connector is used for MIDI data transfer in

the Utility mode with the following operation: [UTILITY] → [F5] MIDI → [SF3] OTHER → MIDI IN/OUT

888

DTX900

MIDI device

MIDI IN connector

MIDI OUT connector

MIDI cable

888

DTX900

MIDI device

MIDI OUT connector

MIDI IN connector

MIDI cable

Synchronizing with an external MIDI instrument (Master and Slave)

The Songs of this instrument can be synchronized to the playback of an external MIDI sequencer, To do this, one device

must be set to internal clock operation and the other (as well as all other devices to be controlled) to external clock. The

device set to internal clock serves as a reference for all connected devices, and is referred to as the “master” instrument.

The connected devices set to external clock are referred to as “slaves.” When recording playback data of an external MIDI

sequencer to a Song of the DTX900 in the above connection example, make sure to set the MIDI synchronization param-

eter to follow external clock with the following operation in the Utility mode.

Страница загружается...

Yamaha DTX900, DTX-900 Инструкция по применению

Похожие модели бренда