English
Operating Instructions
OVEN
Contents
Operating Instructions,1
Warnings,2
Assistance,4
Description of the appliance,5
Description of the appliance,6
Installation,7
Start-up and use,9
Modes,10
Precautions and tips,14
Maintenance and care,14
Troubleshooting,17
7OFK 1039EL PX RU/HA
7OFK1039ELSPX RU/HA
Русскии
Руководство по эксплуатации
ДУХОВОЙ ШКАФ
Содержание
Руководство по эксплуатации,1
Предупреждения,3
Сервисное обслуживание,4
Описание изделия,5
Описание изделия,6
Установка,18
Включение и эксплуатация,20
Программы,22
Предосторожности и рекомендации,26
Техническое обслуживание и уход,27
Неисправности и методы их устранения,29
2
Warnings
WARNING: The appliance and its
accessible parts become hot during use.
Care should be taken to avoid touching
heating elements. Children less than 8
years of age shall be kept away unless
continuously supervised. This appliance
can be used by children aged from 8 years
and above and persons with reduced
physical, sensory or mental capabilities
or lack of experience and knowledge
if they have been given supervision
or instruction concerning use of the
appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and
user maintenance shall not be made by
children without supervision.
Do not use harsh abrasive cleaners or
sharp metal scrapers to clean the oven door
glass since they can scratch the surface,
which may result in shattering of the glass.
“Before initiating the automatic cleaning
cycle:
• clean the oven door;
• remove large or coarse food residues
from the inside of the oven using a
damp sponge. Do not use detergents;
• remove all accessories and the sliding
rack kit (where present);
• do not place tea towels”
Keep children away from the appliance
during the automatic cleaning cycle as
surfaces may become very hot.
Never use steam cleaners or pressure
cleaners on the appliance.
WARNING: Ensure that the appliance is
switched off before replacing the lamp to
avoid the possibility of electric shock.
! When you place the rack inside, make
sure that the stop is directed upwards and
in the back of the cavity.
3
Предупреждения
ВНИМАНИЕ: Данное изделие и его
доступные комплектующие сильно
нагреваются в процессе эксплуатации.
Будьте осторожны и не касайтесь
нагревательных элементов.
Не разрешайте детям младше 8 лет
приближаться к изделию без контроля.
Данное изделие может быть
использовано детьми старше 8 лет и
лицами с ограниченными физическими,
сенсорными или умственными
способностями или без опыта и знания
о правилах использования изделия при
условии надлежащего контроля или
обучения безопасному использованию
изделия с учетом соответствующих
рисков. Не разрешайте детям играть
с изделием. Не разрешайте детям
осуществлять чистку и уход за
изделием без контроля взрослых.
Не используйте абразивные вещества
или режущие металлические скребки
для чистки стеклянной дверцы духового
шкафа, так как они могут поцарапать
поверхность, что может привести к
разбиванию стекла.
Подготовка к автоматической чистке:
• протрите дверцу духовки
• влажной губкой удалите из духовки
наиболее крупные загрязнения. Не
используйте моющие средства;
• выньте все съемные детали и
комплект выдвижных направляющих
(если имеется);
• не вешайте тряпки или кухонные
полотенца на ручку дверцы духового
шкафа.
В процессе пиролитической чистки
поверхности могут сильно нагреться:
не разрешайте детям приближаться к
духовому шкафу.
Никогда не используйте паровые
чистящие агрегаты или агрегаты под
высоким давлением для чистки изделия.
ВНИМАНИЕ: Проверьте, чтобы изделие
было выключено, перед заменой
лампочки во избежание возможных
ударов током.
! При установке решетки проверить,
чтобы фиксатор был повернут вверх
с задней стороны выемки.
4
Assistance
Warning:
The appliance is tted with an automatic diagnostic system
which detects any malfunctions. Malfunctions are signalled
through messages of the following type: “F—” followed by
numbers.
Call for technical assistance in the event of a malfunction.
Before calling for Assistance:
• Check whether you can x the problem yourself.
• Restart the programme to check whether the malfunction
has disappeared.
• If it has not, contact the Authorised Technical Assistance
Service.
! Never use the services of an unauthorised technician.
Please have the following information to hand:
• The type of problem encountered.
• The message shown on the TEMPERATURE display.
• The appliance model (Mod.).
• The serial number (S/N).
The latter two pieces of information can be found on the
data plate located on the appliance.
Сервисное обслуживание
Внимание:
Изделие оснащено системой автоматической
диагностики, позволяющей выявить возможные
неисправности. Неисправности показываются на
дисплее посредством следующих сообщений: “F—” с
последующими цифрами.
В этом случае необходимо вызвать техника из центра
сервисного обслуживания.
Перед тем как обратиться в Центр Технического
обслуживания:
• Проверьте, можно ли устранить неисправность
самостоятельно;
• Вновь запустите программу для проверки
исправности машины;
• В противном случае обратитесь в уполномоченный
Центр Технического обслуживания.
! Никогда не обращайтесь к неуполномоченным
техникам.
При обращении в Центр Технического Обслуживания
необходимо сообщить:
• Тип неисправности;
• сообщение, показываемое на дисплее
ТЕМПЕРАТУРЫ
• Модель изделия (Мод.)
• Номер тех. паспорта (серийный №)
Эти данные вы найдете на паспортной табличке,
расположенной на изделии.
5
Description of the appliance
Overall view
1 POSITION 1
2 POSITION 2
3 POSITION 3
4 POSITION 4
5 POSITION 5
6 GUIDES for the sliding racks
7 DRIPPING PAN
8 GRILL
9 Control panel
Описание изделия
Общии вид
1 ПОЛОЖЕНИЕ 1
2 ПОЛОЖЕНИЕ 2
3 ПОЛОЖЕНИЕ 3
4 ПОЛОЖЕНИЕ 4
5 ПОЛОЖЕНИЕ 5
6 ВЫДВИЖНЫЕ НАПРАВЛЯЮЩИЕ уровней
7 ПРОТИВЕНЬ
8 РЕШЕТКА
9 Панель управления
7
8
9 6
1
2
3
4
5
6
Description of the appliance
Control panel
1. MANUAL COOKING MODE Icons
2. FAST CLEAN selector
3. TEMPERATURE display
4. TEMPERATURE icon
5. DURATION icon
6. TIME display
7. END OF COOKING Icon
8. CONTROL PANEL LOCK icon
9. START / STOP
10. LIGHT icon
11. CLOCK icon
12. MINUTE MINDER Icon
13. TIME / TEMPERATURE ADJUSTMENT Icons
14. PREHEATING / RESIDUAL HEAT icons
15. DOOR LOCK indicator
16. AUTOMATIC/ECO COOKING MODE icons
17. CONTROL PANEL POWER BUTTON
Описание изделия
Панель управления
1. Символы ПРОГРАММ РУЧНОГО РЕЖИМА
2. Выбор FAST CLEAN
3. Дисплей ТЕМПЕРАТУРЫ
4. Символ ТЕМПЕРАТУРА
5. Символ ПРОДОЛЖИТЕЛЬНОСТЬ
6. Дисплей ВРЕМЯ
7. Символ КОНЕЦ ПРИГОТОВЛЕНИЯ
8. Символ БЛОКИРОВКА УПРАВЛЕНИЙ
9. ПУСК / ОСТАНОВКА
10. Символ ОСВЕЩЕНИЕ
11. Символ ЧАСЫ
12. Символ ТАЙМЕР
13. Символы НАСТРОЙКИ ВРЕМЕНИ / ТЕМПЕРАТУРЫ
14. Символы НАГРЕВ / ОСТАТОЧНОЕ ТЕПЛО
15. Индикатор ДВЕРЦА ЗАБЛОКИРОВАНА
16. Символы АВТОМАТИЧЕСКИХ/ECO ПРОГРАММ
17. ВКЛЮЧЕНИЕ ПАНЕЛИ УПРАВЛЕНИЯ
10
11
12
13
15
1
43
7
6
5
8
9
16
2
14
17
GB
7
Installation
! Please keep this instruction booklet in a safe place for
future reference. If the appliance is sold, given away or
moved, please make sure the booklet is also passed on to
the new owners so that they may benet from the advice
contained within it.
! Please read this instruction manual carefully: it contains
important information concerning the safe operation,
installation and maintenance of the appliance.
Positioning
! Do not let children play with the packaging material; it
should be disposed of in accordance with local separated
waste collection standards (see Precautions and tips).
! The appliance must be installed by a qualied professional
in accordance with the instructions provided. Incorrect
installation may damage property or cause harm to people
or animals.
Built-in appliances
Use an appropriate cabinet to ensure that the appliance
operates properly:
• The panels adjacent to the oven must be made of heat-
resistant material.
• Cabinets with a veneer exterior must be assembled with
glues which can withstand temperatures of up to 100°C.
• To install the oven under the counter (see diagram) or
in a kitchen unit, the cabinet must have the following
dimensions:
590 mm.
595 mm.
22,5 mm.*
20,5 mm.
550 mm.
570 mm.
20 mm.
575-585 mm.
45 mm.
560 mm.
550 mm.
min.
* Stainless steel models only
! The appliance must not come into contact with electrical
parts once it has been installed.
The indications for consumption given on the data plate
have been calculated for this type of installation.
Ventilation
To ensure adequate ventilation, the back panel of the
cabinet must be removed. It is advisable to install the oven
so that it rests on two strips of wood, or on a completely
at surface with an opening of at least 45 x 560 mm (see
diagrams).
560 mm.
45 mm.
Centring and xing
Secure the appliance to the cabinet:
• Open the oven door.
• slide out the side gaskets at the top until the 2 xing holes
are exposed;
• Fix the oven to the cabinet using the 2 wood screws.
• reposition the 2 gaskets.
! All parts which ensure the safe operation of the appliance
must not be removable without the aid of a tool.
8
GB
Electrical connection
Ovens equipped with a three-pole power supply cable are
designed to operate with alternating current at the voltage
and frequency indicated on the data plate located on the
appliance (see below).
Fitting the power supply cable
1. Open the terminal board
by inserting a screwdriver
into the side tabs of the
cover. Use the screwdriver
as a lever by pushing it
down to open the cover (see
diagram).
2. Install the power supply
cable by loosening the
cable clamp screw and the
three wire contact screws
L-N- .
Connect the wires to the
corresponding terminals:
the Blue wire to the terminal
marked (N), the Brown wire
to the terminal marked (L)
and the Yellow/Green wire
to the terminal marked
(see diagram).
3. Secure the cable by fastening the clamp screw.
4. Close the cover of the terminal board.
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load
indicated on the data plate (see table).
The appliance must be directly connected to the mains using
an omnipolar switch with a minimum contact opening of 3
mm installed between the appliance and the mains. The
switch must be suitable for the charge indicated and must
comply with current electrical regulations (the earthing wire
must not be interrupted by the switch). The supply cable
must be positioned so that it does not come into contact
with temperatures higher than 50°C at any point (the back
panel of the oven, for example).
! The installer must ensure that the correct electrical
connection has been performed and that it is fully compliant
with safety regulations.
Before connecting the appliance to the power supply, make
sure that
• The appliance is earthed and the plug is compliant with
the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate.
• The voltage is in the range between the values indicated
on the data plate.
N
L
• The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it. Do not use extension
cords or multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
! The manufacturer declines any liability should these
safety measures not be observed.
APPLIANCE SPECIFICATIONS
Dimensions*
width 43.5 cm
height 32,4 cm
depth 41.5 cm
Volume*
59 l
Dimensions**
width 45.5 cm
height 32,4 cm
depth 41.5 cm
Volume**
62 l
Electrical
connections
voltage: 220 - 240 V~ 50/60 Hz or
50 Hz (see data plate)
maximum power absorbed
2800 W
ENERGY
LABEL
Directive 2002/40/EC on the label
of electric ovens. Standard EN 50304
Declared energy consumption
for Forced convection Class –
heating mode:
ECO.
* Only for models with drawn rails.
** Only for models with wire rails.
This appliance conforms to the following
European Economic Community
directives:
- 2006/95/EEC dated 12/12/06 (Low
Voltage) and subsequent amendments.
- 2004/108/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent amendments.
- 93/68/EEC dated 22/07/93 and
subsequent amendments.
- 2012/19/EC and subsequent
amendments.
- 1275/2008 standby/off mode.
GB
9
Start-up and use
WARNING! The oven is
provided with a stop system
to extract the racks and
prevent them from coming
out of the oven (1).
As shown in the drawing,
to extract them completely,
simply lift the racks, holding
them on the front part, and
pull (2).
! The rst time you use your appliance, heat the empty oven with
its door closed at its maximum temperature for at least half an
hour. Make sure that the room is well ventilated before switching
the oven off and opening the oven door. The appliance may emit
a slightly unpleasant odour caused by protective substances
used during the manufacturing process burning away.
! To make the setting process easier, press and hold the “ ”
and “ ” buttons to scroll through the numbers on the display
rapidly.
! Each setting will automatically be stored in the appliance
memory after 10 seconds.
! The touch controls cannot be activated if the user is
wearing gloves.
! In order to optimise the cooking performance, when
starting the selected function, product settings will be
applied that could cause a delayed start of the fan and
heating elements
Some models are equipped with a system of hinges which
allows the door to close slowly, without the user having to
follow the movement through with his/her hand. To use the
system correctly, before closing the door:
• Open the door fully.
• Do not force the closing movement manually.
Control panel lock
! The control panel can be locked while the oven is off, once
cooking has started or nished and during programming.
To lock the oven controls, press and hold the button
for at least 2 seconds. A buzzer will sound and the
TEMPERATURE display shows the key symbol “O—n”. The
icon will light up to indicate lock activation.
To deactivate the lock, press and hold the button again
for at least 2 seconds.
! When cleaning the appliance, the door lock may be closed
accidentally (there is an exposed spring). If this happens,
reopen it by turning the door lock upwards (see gure).
KO OK
Setting the clock
! The clock can only be set when the oven is switched off. If
the oven is in standby mode, pressing the button once will
display the current time setting. Press it again to set the time.
After connection to the power supply network or after a
blackout, the button and the digits on the TIME display
will ash for 10 seconds.
To set the clock:
1. Press the button.
2. Adjust the hour gure using the “ ” and “ ” buttons.
3. Once you have reached the correct hour value, press
the button.
4. Repeat the above process to set the minutes.
If a blackout occurs, it will be necessary to reset the clock.
If the icon ashes on the display, this indicates that the
clock has not been set correctly.
Setting the minute minder
! The minute minder may be set regardless of whether the
oven is switched on or off. It does not switch the oven on or off.
When the set time has elapsed, the timer emits a buzzer
that will automatically stop after 30 seconds or when any
active button on the control panel is pressed.
To adjust the timer proceed as follows:
1. Press button .
2. Set the desired time using buttons “ ” and “ ”.
3. Once you have reached the desired value, press the
button again.
The lit symbol will remind you that the minute minder
is on.
To cancel the minute minder, press the button and
use the “ ” and “ ” buttons to set the time to 00:00. Press
button again.
The icon will switch off to indicate that the minute minder
has been disabled.
Starting the oven
1. Switch the control panel on by pressing the button.
The appliance buzzer sounds three times (ascending) and
all buttons light up in sequence.
2. Press the button corresponding to the desired cooking
mode. The TEMPERATURE display shows:
- the temperature associated with the mode, if programming
manually;
- “Auto”, if programming is automatic.
The TIME display shows:
- the current time, if programming manually;
- the duration, if programming is automatic.
3. Press the button to begin cooking.
4. The oven will begin its preheating phase, the preheating
indicators will light up as the temperature rises.
5. When the preheating process has nished, a buzzer sounds
and all the preheating indicator lights show that this stage has
been completed: the food can then be placed in the oven.
10
GB
6. During cooking it is always possible to:
- change the temperature by pressing the button,
followed by the “ ” and “ ” buttons (manual modes only);
- set the duration of a cooking mode (see Cooking Modes);
- press the button to stop cooking. In this case the
appliance stores the temperature modied previously in its
memory (manual modes only);
- switch off the oven by pressing the button for 3 seconds.
7. If a blackout occurs while the oven is already in operation,
an automatic system within the appliance will reactivate the
cooking mode from the point at which it was interrupted,
provided that the temperature has not dropped below a
certain level. Programmed cooking modes which have not
yet started will not be restored and must be reprogrammed
(for example: a cooking mode has been programmed to
start at 20:30. At 19:30 a blackout occurs. When the power
supply is restored, the mode will have to be reprogrammed).
! There is no preheating stage for the GRILL mode.
! Never put objects directly on the bottom of the oven; this
will prevent the enamel coating from being damaged.
! Always place cookware on the rack(s) provided.
Cooling ventilation
In order to cool down the external temperature of the oven, a
cooling fan blows a stream of air between the control panel and
the oven door, as well as towards the bottom of the oven door.
At the beginning of the FAST CLEAN mode, the cooling fan
operates at low speed.
! Once cooking has been completed, the cooling fan continues
to operate until the oven has cooled down sufciently.
Oven light
The light comes on when the oven door is opened or when
a cooking mode starts. When models featuring LED INSIDE
technology begin cooking, the LEDs on the door light up for
improved illumination of all cooking levels.
The button can be used to switch on the light at any time.
Residual heat indicators
The appliance is tted with a residual heat indicator. When
the oven is off, the “residual heat” bar on the display lights
up to indicate high temperatures inside the oven cavity. The
individual segments of the bar switch off one by one as the
temperature inside the oven falls.
Concealed handle
Some models have a concealed handle built into the oven door.
Simply press lightly and the push/push opening will improve
your grip when opening and closing the oven. When you have
nished using it, close it again by applying light pressure.
Demo mode
The oven can operate in the DEMO mode: all heating
elements are deactivated, and the controls remain operative.
To activate DEMO mode, press and release button , then
buttons “ ” and “ ” simultaneously for 6 seconds, and then
press and release button .
A buzzer sounds and the TEMPERATURE display shows
“dEon”. To deactivate DEMO mode, when the oven is off
press and hold button and button “ ” simultaneously
for 3 seconds. A buzzer sounds and the “dEoF” message
disappears from the display.
Restoring the factory settings
The oven factory settings can be restored to reset all
selections made by the user (clock and customised
durations). To carry out a reset, switch off the oven, then
press and hold the button corresponding to the rst manual
cooking mode (top left) and the button simultaneously
for 6 seconds. Once the restore procedure is complete, a
buzzer will sound. The rst time the button is pressed, the
oven will behave as if it is being switched on for the rst time.
Standby
This product complies with the requirements of the latest
European Directive on the limitation of power consumption
of the standby mode. If no buttons are pressed for 30
minutes and the control panel/door lock has not been
activated, the appliance automatically reverts to standby
mode. Standby mode is indicated by the high luminosity
“Clock button” light. As soon as interaction with the machine
resumes, the system’s operating mode is restored.
Modes
! In order to guarantee wonderfully soft and crunchy
foodstuffs, the oven releases – in the form of water vapour -
the humidity naturally withheld in the food itself. In this way,
optimal cooking results can be achieved for all types of food.
! Every time the oven is switched on, it suggests the rst
manual cooking mode.
Manual cooking modes
! All cooking modes have a default cooking temperature which
may be adjusted manually to a value between 30°C and
250°C as desired (300°C for GRILL mode). Any temperature
adjustments will be stored in the appliance memory and
suggested again the next time this mode is used. If the
selected temperature is lower than the temperature inside the
oven, the text “Hot” appears on the TEMPERATURE display.
However, it will still be possible to start cooking.
MULTILEVEL mode
All heating elements and the fan are activated. Since the
heat remains constant throughout the oven, the air cooks
and browns food in a uniform manner. A maximum of two
racks may be used at the same time.
GB
11
BARBECUE mode
The top heating element and the rotisserie spit (where
present) are activated. The high and direct temperature
of the grill is recommended for food which requires a high
surface temperature. Always cook in this mode with the oven
door closed (see “Practical cooking advice”).
FAN GRILLING mode
The top heating element and the rotisserie spit (where
present) are activated and the fan begins to operate.
During part of the cycle the circular heating element is
also activated. This combination of features increases the
effectiveness of the unidirectional thermal radiation provided
by the heating elements through the forced circulation of
the air throughout the oven.
This helps prevent food from burning on the surface and
allows the heat to penetrate right into the food. Always
cook in this mode with the oven door closed (see “Practical
cooking advice”).
LOW TEMPERATURE modes
This type of cooking can be used for proving, defrosting,
preparing yoghurt, heating dishes at the required speed and
slow cooking at low temperatures. The temperature options
are: 40, 65 and 90°C.
PIZZA modes
The top and circular heating elements switch on and the fan
begins to operate. This combination heats the oven rapidly.
If you use more than one rack at a time, switch the position
of the dishes halfway through the cooking process.
BAKING mode
The rear heating element and the fan are switched on, thus
guaranteeing the distribution of heat in a delicate and uniform
manner throughout the entire oven. This mode is ideal for baking
temperature sensitive foods (such as cakes, which need to rise).
ECO mode
The rear heating element and the fan are switched on,
thus guaranteeing the distribution of heat in a delicate and
uniform manner throughout the entire oven.This energy
saving mode is recommended for small dishes, ideal for
heating foods and nishing off cooking.
Rotisserie spit*
To operate the rotisserie
function (see diagram)
proceed as follows:
1. Place the dripping pan in
position 1.
2. Place the rotisserie
support in position 3 and
insert the spit in the hole
provided on the back panel
of the oven.
3. Start the rotisserie
function by selecting the or modes;
! When mode is on, the rotisserie will stop if the door
is opened.
Automatic cooking modes
! The temperature and cooking duration are pre-set values,
guaranteeing a perfect result every time - automatically. These
values are set using the C.O.P.® (Programmed Optimal
Cooking) system. The cooking cycle stops automatically and
the oven indicates when the dish is cooked. You may start
cooking whether the oven has been preheated or not.
The cooking duration can be customised according to
personal taste by modifying the relevant value - before
cooking begins - by ±5/20 minutes depending on the
selected programme. The duration can however be modied
even once cooking has begun. If the value is modied
before the programme begins, it is stored in the memory
and suggested again by the appliance when the programme
is next used. If the temperature inside the oven is higher
than the suggested value for the selected mode, the text
“Hot” appears on the TEMPERATURE display and it will
not be possible to begin cooking; wait for the oven to cool.
! When the cooking stage has been reached, the oven
buzzer sounds.
! Do not open the oven door as this will disrupt the cooking
time and temperature.
BEEF mode
Use this function to cook beef, pork and lamb. Place the
food inside the oven while it is still cold. The dish may also
be placed in a preheated oven.
FISH FILLETS mode
This function is ideal for cooking small-medium llets. Place
the food inside the oven while it is still cold.
BREAD mode
Use this function to bake bread. To obtain the best results,
we recommend that you carefully observe the instructions
below:
• follow the recipe;
• do not exceed the maximum weight of the dripping pan;
• remember to pour 50 g (0,5 dl) of cold water into the
baking tray in position 5.
• The dough must be left to rise at room temperature for
1 – 1 ½ hours (depending on the room temperature) or
until the dough has doubled in size.
Recipe for BREAD:
1 Dripping pan holding 1000 g Max, lower level
2 Dripping pans each holding 1000 g Max, medium and
lower levels
Recipe for 1000 g of dough: 600 g our, 360 g water, 11g
salt, 25 g fresh yeast (or 2 sachets of powder yeast)
Method:
• Mix the our and salt in a large bowl.
* Only available in certain models.
12
GB
• Dilute the yeast in lukewarm water (approximately 35
degrees).
• Make a small well in the mound of our.
• Pour in the water and yeast mixture.
• Knead the dough by stretching and folding it over itself
with the palm of your hand for 10 minutes until it has a
uniform consistency and is not too sticky.
• Form the dough into a ball shape, place it in a large bowl
and cover it with transparent plastic wrap to prevent the
surface of the dough from drying out. Select the manual
LOW TEMPERATURE function on the oven and set the
temperature to 40°C. Place the bowl inside and leave
the dough to rise for approximately 1 hour (the dough
should double in volume).
• Cut the dough into equal sized loaves.
• Place them in the dripping pan, on a sheet of baking
paper.
• Dust the loaves with our.
• Make incisions on the loaves.
• Place the food inside the oven while it is still cold.
• Start the BREAD cooking mode.
• Once baked, leave the loaves on one of the grill racks
until they have cooled completely.
BAKED CAKES mode
This function is ideal for cooking desserts which are made
using natural yeast, baking powder and desserts which
contain no yeast. Place the dish in the oven while it is still
cold. The dish may also be placed in a preheated oven.
TARTS mode
This function is ideal for all tart recipes (which normally need
to be heated well from underneath). Place the food inside
the oven while it is still cold.
The dish may also be placed in a preheated oven.
Programming cooking
! A cooking mode must be selected before programming
can take place.
! Once a cooking mode has been selected, the button
is activated; it will then be possible to program a duration.
The button is only activated after a duration has been
set; it will then be possible to program a delayed start.
Programming the duration
1. Press the button; the button and the numbers on
the TIME display will ash.
2. Set the duration by pressing buttons “ ” and “ ”.
3. Once you have reached the desired duration, press the
button again.
4. Press the button to begin cooking.
5. When cooking has nished, “END” appears on the
TEMPERATURE display and a buzzer sounds.
• For example: it is 9:00 a.m. and a duration of 1 hour and
15 minutes is programmed. The programme will stop
automatically at 10:15 a.m.
Programming delayed cooking
! A cooking duration must be set before the cooking end
time can be scheduled.
! For the delayed programming to work properly, the clock
should be set to the correct time.
1. Press the button and repeat steps 1 to 3 as described
for the duration setting.
2. Then press the button and set the end time using
the “ ” and “ ” buttons.
3. Once you have reached the desired end time, press the
button again.
4. Press the button to activate the programmed mode.
The and buttons will ash alternately to indicate that
programming has taken place; in the time before cooking
starts, the TIME display will show the duration and the
cooking end time alternately.
5. Once cooking has finished, “END” appears on the
TEMPERATURE display and a buzzer sounds.
• For example: it is 9:00 a.m. and a time of 1 hour and 15
minutes is programmed, while the end time is set to 12:30.
The programme will start automatically at 11:15 a.m.
To cancel programming press the button.
Practical cooking advice
! Do not place racks in position 1 and 5 during fan-assisted
cooking. This is because excessive direct heat can burn
temperature sensitive foods.
! In the GRILL and FAN GRILLING cooking modes,
particularly when using the rotisserie spit, place the dripping
pan in position 1 to collect cooking residues (fat and/or
grease).
MULTILEVEL
• Use positions 2 and 4, placing the food which requires
more heat on 2.
• Place the dripping pan on the bottom and the rack on
top.
GRILL
• Place the rack in position 3 or 4. Position the food in the
centre of the rack.
• We recommend that the temperature is set to its
maximum level. The top heating element is regulated by
a thermostat and may not always operate constantly.
PIZZA
• Use a lightweight aluminium pizza pan. Place it on the
rack provided.
For a crispy crust, do not use the dripping pan as this
extends the total cooking duration and prevents the crust
from forming.
• If the pizza has a lot of toppings, we recommend adding
the mozzarella cheese to the top of the pizza halfway
through the cooking process.
GB
13
Modes Foods Weight
(in kg)
Preheating
Manual
Standard
guide
rails
Sliding
guide
rails
Multilevel*
1+1
1
1
1
2 and 4
2 and 4
2 and 4
1 and 2/3
2
1 or 2
2
2 and 4
1 and 3
1 and 3
1 and 3
1 and 3
1 and 3
1
1
1
1 and 3
1 and 3
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
20-25
30-35
20-30
65-75
45-50
30-35
35-40
20-25
10-20
20-25
25-35
Grill*
1
0,7
0,7
0,7
0,5
0,8
0,7
n° 4 or 5
n° 4 or 6
1
1
4
4
4
4
3 or 4
4
4
4
4
-
-
3
3
3
3
2 or 3
3
3
3
3
-
-
no
no
no
no
no
no
no
no
no
no
no
300
300
300
300
300
300
300
300
300
300
300
10-20
10-15
10-15
10-15
15-20
10-20
10-20
10-12
3-5
70-80
70-80
Fan grilling*
1,5
1
1,5
1,5
1
1
1
2
2
-
-
2
2
2
2
2
-
-
2
2
2
no
no
no
no
no
no
no
210
200
210
210
210
210
210
55-60
30-35
70-80
60-70
60-75
70-80
40-45
Proving / Defrosting
White meringues
Meat / Fish
-
-
-
2
2
2
1
1
1
no
no
no
40
65
90
-
8-12 ore
90-180
Pizza*
Pizza
Focaccia bread
0,5
0,5
2
2
1
1
yes
yes
15-20
20-25
Baking*
0,5
1
0,7
0,7
0,6
0,7
0,7
0,8
0,5
0,5
2 or 3
2 or 3
2 or 3
2 and 4
2 or 3
1 and 3
1 and 3
2
1 and 3
2
1 or 2
1 or 2
1 or 2
1 and 3
1 or 2
1 and 2
1 and 2
1
1 and 2
1
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
180
180
180
180-190
160-170
180-190
180
200
90
210
25-35
40-50
45-55
20-25
35-40
20-30
20-25
30-35
180
20-25
Automatic**
Beef
Roast dishes12 or 32 no
Fish fillets
Cod
Perch
Trout
0,4-0,5
0,4-0,5
0,4-0,5
2 or 3
2 or 3
2 or 3
2
2
2
no
no
no
Bread***
Bread (see recipe)
11 or 21 no
Baked cakes
Baked cakes
12 or 32 no
Tarts
Tarts
0,52 or 32 no
Cooking advice table
Low
temperature*
Rack position Recommended
Temperature
(°C)
Cooking
duration
(minutes)
1 and 3 and 5
1 and 3 and 5
1 and 2 and 4
1 and 2 and 4
50 0,5
210-220
180
160-170
200-210
190-200
180
180-190
190
180
210
190-200
210-220
190-200
! ECO programme: This programme – which has longer cooking times but guarantees sensible energy saving – is recommended for dishes such as fish
fillets, small pastries and ve
g
etables. It is also suitable for warmin
g
foodstuffs and for completin
g
cookin
g
.
14
GB
Precautions and tips
! This appliance has been designed and manufactured
in compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
General safety
• The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial use.
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
• When moving or positioning the appliance, always use
the handles provided on the sides of the oven.
• Do not touch the appliance while barefoot or with wet or
damp hands and feet.
• The appliance must be used by adults only for
the preparation of food, in accordance with the
instructions provided in this booklet. Any other
use of the appliance (e.g. for heating the room)
constitutes improper use and is dangerous. The
manufacturer may not be held responsible for any
damage caused as a result of improper, incorrect
and unreasonable use of the appliance.
• Do not touch the heating elements or certain parts
of the oven door when the appliance is in use; these
parts become extremely hot. Keep children well away
from the appliance.
• Make sure that the power supply cables of other electrical
appliances do not come into contact with the hot parts of
the oven.
• The ventilation and heat dispersal openings must never
be obstructed.
• Always grip the oven door handle in the centre: the ends
may be hot.
• Always use oven gloves when placing cookware in the
oven or when removing it.
• Do not use aluminium foil to line the bottom of the oven.
• Do not place ammable materials in the oven: if the
appliance is switched on accidentally, the materials could
catch re.
• When unplugging the appliance, always pull the plug
from the mains socket; do not pull on the cable.
• Do not perform any cleaning or maintenance work without
having disconnected the appliance from the electricity
mains.
• If the event of malfunctions, under no circumstances
should you attempt to perform the repairs yourself.
Contact an authorised Service Centre (see Assistance).
• Do not rest objects on the open oven door.
• Do not let children play with the appliance.
• The appliance should not be operated by people (including
children) with reduced physical, sensory or mental
capacities, by inexperienced individuals or by anyone
who is not familiar with the product. These individuals
should, at the very least, be supervised by someone who
assumes responsibility for their safety or receive preliminary
instructions relating to the operation of the appliance.
• The appliance is not intended to be operated by
means of an external timer or separate remote-
control system.
Disposal
• When disposing of packaging material: observe local
legislation so that the packaging may be reused.
• The European Directive 2012/19/EC on Waste
Electrical and Electronic Equipment (WEEE), requires
that old household electrical appliances must not
be disposed of in the normal unsorted municipal
waste stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product
reminds you of your obligation, that when you dispose
of the appliance it must be separately collected.
Consumers should contact their local authority or retailer
for information concerning the correct disposal of their
old appliance.
Respecting and conserving the environment
• You can help to reduce the peak load of the electricity
supply network companies by using the oven in the
hours between late afternoon and the early hours of
the morning. The cooking mode programming options,
the “delayed cooking” mode (see Cooking modes) and
“delayed automatic cleaning” mode (see Care and
Maintenance) in particular, enable the user to organise
their time efciently.
• Always keep the oven door closed when using the GRILL
and FAN GRILLING modes: this will achieve improved
results while saving energy (approximately 10%).
• Check the door seals regularly and wipe them clean
to ensure they are free of debris so that they adhere
properly to the door, thus avoiding the dispersal of heat.
! This product complies with the requirements of the latest
European Directive on the limitation of power consumption
of the standby mode.
Maintenance and care
Switching the appliance off
Disconnect your appliance from the electricity supply before
carrying out any work on it.
Cleaning the appliance
• Slight differences in colour on the front of the oven are due
to the different materials used, i.e. glass, plastic or metal.
• Any shady areas resembling grooves on the oven door
glass are caused by reections from the oven light.
• The enamel is branded at very high temperatures. This
process may cause colour variations. This is normal and
will not affect appliance operation in any way. The thin
edges of the sheet metal cannot be entirely enamelled
and may therefore appear to be unnished. This will not
affect the rust protection.
• The stainless steel or enamel-coated external parts and
the rubber seals may be cleaned using a sponge that
has been soaked in lukewarm water and neutral soap.
Use specialised products for the removal of stubborn
stains. After cleaning, rinse and dry thoroughly. Do not
use abrasive powders or corrosive substances.
GB
15
• The inside of the oven should ideally be cleaned after
each use, while it is still lukewarm. Use hot water and
detergent, then rinse well and dry with a soft cloth. Do
not use abrasive products.
• All accessories - with the exception of the sliding racks
- can be washed like everyday crockery, and are even
dishwasher safe.
• We recommend that detergents are not sprayed directly
onto the control panel, but that a sponge is used instead.
! Never use steam cleaners or pressure cleaners on the
appliance.
Cleaning the oven door
! The door of LED INSIDE models cannot be removed.
Clean the glass part of the oven door using a sponge and
a non-abrasive cleaning product, then dry thoroughly with
a soft cloth. Do not use rough abrasive material or sharp
metal scrapers as these could scratch the surface and cause
the glass to crack.
For more thorough cleaning purposes, the oven door may
be removed:
1. Open the oven door fully (see diagram).
2. Use a screwdriver to lift up and turn the small levers F
located on the two hinges (see diagram).
F
3. Grip the door on the two outer
sides and close it approximately
half way. Pull the door towards you,
lifting it out of its slot (see diagram).
To replace the door, reverse this
sequence.
Inspecting the seals
Check the door seals around the oven regularly. If the seals
are damaged, please contact your nearest Service Centre
(see Assistance). We recommend that the oven is not used
until the seals have been replaced.
Replacing the light bulb
To replace the oven light
bulb:
1. Remove the glass cover
of the lamp-holder.
2. Remove the light bulb and
replace it with a similar one:
halogen lamp voltage 230 V,
wattage 25 W, cap G 9.
3. Replace the glass cover
(see diagram).
Glass cover
Lamp
Lamp
Holder
compartment
! Do not touch the light bulb directly with your hands.
! Do not use the oven lamp as/for ambient lighting.
Sliding rack kit assembly
To assemble the sliding
racks:
1. Remove the two frames,
lifting them away from the
spacers A (see gure).
2. Choose which shelf to use
with the sliding rack. Paying
attention to the direction in
which the sliding rack is to
be extracted, position joint B
and then joint C on the
frame.
3. Secure the two frames
with the guide rails using the
holes provided on the oven
walls (see diagram). The
holes for the left frame are
situated at the top, while the
holes for the right frame are
at the bottom.
4. Finally, t the frames on
the spacers A.
! Do not place the sliding racks in position 5.
Automatic cleaning with the FAST CLEAN
function
With the FAST CLEAN mode, the internal temperature of the
oven reaches 500°C. The pyrolytic cycle is activated, burning
away food and grime residues. Dirt is literally incinerated.
Keep children away from the appliance during the automatic
cleaning cycle as surfaces may become very hot. Particles
may ignite inside the oven as a result of the combustion
process. There is no cause for concern: this process is both
normal and hazard-free.
Before initiating the FAST CLEAN mode:
• clean the oven door;
• remove large or coarse food residues from the inside of
the oven using a damp sponge. Do not use detergents;
• remove all accessories and the sliding rack kit (where
present);
• do not place tea towels or pot holders over the oven
handle.
A
B
C
Left
guide rail
Right guide
rail
Direction
of extraction
D
16
GB
! If the oven is too hot, the pyrolytic cycle may not start.
Wait for the oven to cool down.
! The programme may only be started once the oven door
has been closed.
To activate the Fast Clean programme:
1. Switch the control panel on by pressing the button.
2. Press the button; the TIME display will show the default
duration of 1:30 h (normal cycle), while he TEMPERATURE
display will show “Piro” and “nor” alternately;
3. The desired cleaning level can be selected by pressing
the button, then:
- pressing “ ” to switch to the intensive cycle: the duration
is 2 h and the TEMPERATURE display shows the text “Piro”
and “int” alternately;
- pressing “ ” to switch to the economy cycle: the duration
is 1 h and the TEMPERATURE display shows the text “Piro”
and “eco” alternately.
Safety devices
• the door locks automatically as soon as the temperature
reaches a high value; the icon lights up on the
display;
• pressing the button cancels the cleaning cycle t any
time;
• if a malfunction occurs, the heating elements will be
switched off;
• once the oven door has been locked, you cannot change
the duration and end time settings.
Programming delayed automatic cleaning
! Programming is possible only after selecting the FAST
CLEAN mode.
1. Press the button and set the end time using the “
” and “ ” buttons.
2. Once you have reached the desired end time, press the
button again.
3. Press the button to activate the programmed mode.
4. When the selected time has elapsed, “END” appears on
the TEMPERATURE display and a buzzer sounds.
• For example: it is 9:00 a.m. and the Economy (ECO)
FAST CLEAN level has been selected, with the default
duration of 1 hour. 12:30 is scheduled as the end time.
The programme will start automatically at 11:30 a.m.
The icons and ash to indicate that programming
has taken place. After programming, in the time before the
Fast Clean mode starts, the TIME display indicates the
duration and end of the Fast Clean mode alternately.
To cancel programming press the button.
Once the automatic cleaning cycle is over
Before you can open the oven door, you will have to wait
for the icon to switch off: this indicates the oven
temperature has dropped to an acceptable level. You will
notice some white dust deposits on the bottom and the sides
of your oven; remove these deposits with a damp sponge
once the oven has cooled down completely. Alternatively,
you can make use of the already heated oven, in which
case it is not necessary to remove the deposits, they are
completely harmless and will not affect your food in any way.
NOTICE
Do not place
or rest anything
on the open door
Make sure that the racks
and dripping pans have been
inserted fully before closing the door
Please read the manual
carefully for information
regarding the automatic
cleaning (pyrolytic) cycle
GB
GB
17
Problem
Possible cause
Solution
The appliance has just been
connected to the electricity mains
or there has been a blackout.
Set the clock.
A programmed cooking mode
does not start.
There has been a blackout. Reprogram the cooking mode.
Only the high luminosity
“Clock button” is lit.
The appliance is in standby mode Press any button to exit
standby mode.
The temperature inside the oven
is higher than the suggested
value for the selected mode.
Wait for the oven to cool down.
Fan-assisted cooking has been
selected and the food looks burnt.
Positions 1 and 5: the direct
heat could cause
temperature-sensitive
foods to burn.
We recommend switching
dripping pan positions halfway
through cooking.
The “Clock button” and the
digits on the display flash.
An automatic mode has been
selected. “Hot” appears on the
display and cooking does not
start.
Troubleshooting
18
RS
Установка
! Важно сохранить данное руководство для его
последующих консультации. В случае продажи,
передачи изделия или при переезде на новое место
жительства необходимо проверить, чтобы руководство
оставалось вместе с изделием, для того чтобы его новыи
владелец мог ознакомиться с правилами эксплуатации
и с соответствующими предупреждениями.
! Внимательно прочитаите инструкции: в них содержатся
важные сведения об установке, эксплуатации и
безопасности изделия.
Расположение
! Не разрешаите детям играть с упаковочными
материалами. Упаковочные материалы должны быть
уничтожены в соответствии с правилами раздельного
сбора мусора (см. Предосторожности и рекомендации).
! Монтаж изделия производится в соответствии
с данными инструкциями квалифицированными
специалистами. Неправильныи монтаж изделия может
стать причинои повреждения имущества и причинить
ущерб людям и домашним животным.
Встроенный монтаж
Для обеспечения исправного функционирования
встраиваемого изделия кухонный элемент должен иметь
соответствующие характеристики:
• панели кухонных элементов, прилегающих к духовому
шкафу, должны быть выполнены из термостойкого
материала;
• клей кухонных элементов элементов, шпонированных
деревом, должен быть устойчивым к температуре
100°C.
• для встраивания духового шкафа под кухонным
топом (см. схему) или в пенал ниша кухонного
элемента должна иметь следующие размеры:
590 mm.
595 mm.
22,5 mm.*
20,5 mm.
550 mm.
570 mm.
20 mm.
575-585 mm.
45 mm.
560 mm.
550 mm.
min.
* Только для моделей из нержавеющей стали
! После встраивания изделия в кухонный элемент
должна быть исключена возможность касания к
электрическими частями.
Расход электроэнергии, указанный на паспортной
табличке изделия, был замерян для данного типа
монтажа.
Вентиляция
Для обеспечения надлежащеи вентиляции необходимо
снять заднюю панель ниши кухонного элемента.
Рекомендуется установить духовои шкаф на два
деревянных бруска или на сплошное основание с
отверстием диаметром не менее 45 х 560 мм (см чертежи).
560 mm.
45 mm.
Центровка и крепление
Для крепления изделия к кухонному элементу:
• откройте дверцу духовки;
• снять боковые уплотнения в верхней части,
освобождая 2 крепежных отверстия;
• прикрепите духовой шкаф к нише 2 шурупами для
дерева;
• установить на место 2 уплотнения.
! Все защитные элементы должны быть закреплены
таким образом, чтобы их можно было снять только при
помощи специального инструмента.
Электрическое подключение
Духовые шкафы, укомплектованные трехполюсным
сетевым кабелем, расчитаны на функционирование
с переменным током с напряжением и частотой
электропитания, указанными на паспортной табличке с
данными (см. ниже).
19
RS
Подсоединение сетевого кабеля
1. Откройте зажимную
коробку, нажав при помощи
отвертки на выступы с
боков крышки: потяните
и откройте крышку (см.
схему).
2. Порядок подсоединения
сетевого кабеля: отвинтите
винт кабельного сальника
и три винта контактов L-N-
и затем прикрепите
провода под головками
винтов, соблюдая цветовую
маркировку Синий (N)
Коричневый (L) Желто-
зеленый (см. схему).
3. Закрепите сетевой
кабель в специальном
кабельном сальнике.
4. Закройте крышку
зажимной коробки.
Подсоединение сетевого шнура изделия к сети
электропитания
Установите на сетевой кабель нормализованную
штепсельную вилку, расчитанную на нагрузку, указанную
на паспортной табличке (см. сбоку).
В случае прямого подключения к сети электропитания
между изделием и сетью необходимо установить
многополюсный выключатель с минимальным
расстоянием между контактами 3 мм, расчитанный
на данную нагрузку и соответствующий действующим
нормативам (выключатель не должен размыкать провод
заземления). Сетевой кабель должен быть расположен
таким образом, чтобы ни в одной точке его температура
не превышала температуру помещения более чем на
50°C (например, задняя панель духового шкафа).
! Электромонтер несет ответственность за правильное
подключение изделия к электрическои сети и за
соблюдение правил безопасности.
Перед подключением изделия к сети электропитания
проверьте следующее:
• розетка должна быть соединена с заземлением и
соответствовать нормативам;
• сетевая розетка должна быть рассчитана на
максимальную потребляемую мощность изделия,
указанную в таблице технических характеристик;
• напряжение и частота тока сети должны
соответствовать электрическим данным изделия;
• сетевая розетка должна быть совместима со штепсельнои
вилкои изделия. В противном случае замените розетку
или вилку; не используите удлинители или троиники.
! Изделие должно быть установлено таким образом,
чтобы электрическии провод и сетевая розетка были
легко доступны.
N
L
! Электрическии провод изделия не должен быть согнут
или сжат.
! Регулярно проверяите состояние кабеля
электропитания и в случае необходимости поручите
его замену только уполномоченным техникам (см.
Техническое обслуживание).
! Производитель не несет ответственности за
последствия несоблюдения перечисленных выше
требовании.
* Только для моделей с направляющими, изготовленными методом вытяжки.
** Только для моделей с направляющими из прутка.
ПАСПОРТНАЯ ТАБЛИЧКА
Габаритные
размеры*
ширина 43,5 см.
высота 32,4 см.
глубина 41,5 см.
Объем*
59 л
Электрическое
подключение
напряжение 220-240 В ~ 50/60 Гц
или
50 Гц
(см. Паспортную табличку),
максимальная поглощаемая
мощность 2800 Вт
ENERGY
LABEL
Директива 2002/40/СЕ об этикетках
электрических духовых шкафов.
Норматив EN 50304
Заявление о расходе электроэнергии
класса принудительной
конвекции - режим нагрева:
ECO.
Данное изделие соответствует
следующим Директивам
Европейского Сообщества:
2006/95/CEE от 12.12.06 (Низкое
напряжение) с последующими
изменениями – 2004/108/СЕЕ от
15.12.2004 (Электромагнитная
совместимость) с последующими
изменениями – 93/68/СЕЕ от 22/07/93
с последующими изменениями.
- 2012/19/CE с последующими
изменениями.
- 1275/2008 режим
энергосбережения/выкл.
Габаритные
размеры**
ширина 45,5 см.
высота 32,4 см.
глубина 41,5 см.
Объем**
62 л
20
RS
Включение и эксплуатация
ВНИМАНИЕ! Духовой
шкаф укомплектован
системой блокировки
решеток, позволяющей
вынимать их из духовки
не полностью (1).
Для полного вынимания
решеток достаточно
поднять их, как показано
на схеме, взяв их за передний край, и потянуть на себя
(2).
! При первом включении духового шкафа рекомендуем
прокалить его примерно в течение часа при
максимальной температуре с закрытой дверцей. Затем
выключите духовой шкаф, откройте дверцу и проветрите
помещение. Запах, который вы можете почувствовать,
вызван испарением веществ, использованных для
предохранения духового шкафа.
! Для облегчения настройки держите нажатыми кнопки
“ ” и “ ” : цифры на дисплее будут сменяться быстрее.
! Каждая настройка автоматически сохраняется в
памяти по прошествии 10 секунд.
! Активировать сенсорные кнопки touch в перчатках нельзя.
! Для оптимизации приготовления в момент
активирования выбранной функции производится
настройка параметром изделия, которая может вызвать
задержку включения вентилятора и нагревательных
элементов.
Некоторые модели укомплектованы петельной
системой, позволяющей плавно закрыть дверцу, не
прижимая ее рукой. Для правильного использования
системы перед закрыванием дверцы:
• полностью открыть дверцу.
• избегать закрывания дверцы с силой.
Блокировка управлений
! Управления можно заблокировать при выключенной
духовке, после начала или по завершении приготовленя
и в процессе программирования.
Для блокировки управлений духовки нажмите кнопку
примерно на 2 секунды. Раздается звуковой
сигнал, на дисплее ТЕМПЕРАТУРЫ появляется символ
ключа “O—n”. Включенный символ означает, что
блокировка активирована. Для разблокировки вновь
нажмите примерно на 2 секунды кнопку .
! При чистке изделия можно случайно закрыть блокировку
дверцы (видна пружина). В этом случае открыть ее
можно, повернув блокировку дверцы вверх (см. схему).
KO OK
Настройка часов
! Настройка часов производится только при выключенной
духовке. Если духовка в режиме энергосбережения, при
первом нажатии кнопки показывается текущее время.
Вновь нажмите эту кнопку для настройки времени.
После подключения к электросети или после отключения
энергоснабжения кнопка и цифры на дисплее
ВРЕМЯ мигают в течение 10 секунд.
Настройка часов:
1. Нажмите кнопку .
2. Выставите время при помощи кнопок “ ” и “ ”.
3. Выставив точное время, вновь нажмите кнопку .
4. повторить вышеописанную операцию для выставления
минут.
В случае прерывания энергоснабжения необходимо
вновь выставить время. Символ , мигающий на
дисплее, показывает, что часы настроены неправильно.
Настройка таймера
! Настроить таймер можно как при включенном, так и
при выключенном духовом шкафу. Таймер не управляет
включением или выключением духового шкафа.
По истечении заданного времени таймер включает
звуковой сигнал, который прерывается через 30 секунд
или после нажатия на любую активированную кнопку.
Порядок настройки таймера:
1. Нажмите кнопку .
2. Настроить нужное время при помощи кнопок и .
3. Выставив нужное время, вновь нажмите кнопку .
Включенный символ показывает, что таймер
включен.
Для отмены функции таймера нажмите кнопку и при
помощи кнопок “ ” и “ ” установите время на 00:00.
Вновь нажмите кнопку .
Выключение символа означает отключение таймера.
Порядок включения духового шкафа
1. Включите консоль управления при помощи кнопки
. Изделие издает три звуковых сигнала возрастающей
громкости, и последовательно загораются все кнопки.
2. Нажмите кнопку нужной программы приготовления.
На дисплее ТЕМПЕРАТУРЫ показывается:
- если выбрана программа приготовления в ручном
режиме, температура данной программы;
- “Auto” при выборе приготовления в автоматическом
режиме.
на дисплее ВРЕМЯ показывается:
- при выборе программы приготовления в ручном
режиме, текущее время;
- продолжительность при выборе приготовления в
автоматическом режиме.
3. Нажмите кнопку для начала приготовления.
4. Духовка начнет нагреваться, индикаторы нагрева
будут загораться по мере повышения температуры.
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/