Pioneer A-70DA-S Руководство пользователя

A-70DA-K/-S
A-
50DA-K/-S
Integrated Amplifier | Amplificateur Intégré | 
Eingebauter Verstärker | Amplificatore Integrato | 
Geïntegreerde versterker | Amplificador integrado | 
Operating Instructions | Mode d’emploi | Bedienungsanleitung | 
Istruzioni per I’uso | Handleiding | Manual de instrucciones | 
Инструкции по эксплуатации
Интегральный усилитель
A70_SYXE8_0728.book  1 ページ  ２０１５年７月２８日　火曜日　午後３時５４分

WARNING

This equipment is not waterproof. To prevent a fire or

shock hazard, do not place any container filled with

liquid near this equipment (such as a vase or flower

pot) or expose it to dripping, splashing, rain or

moisture.

D3-4-2-1-3_A1_En

WARNING

To prevent a fire hazard, do not place any naked flame

sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A1_En

VENTILATION CAUTION

When installing this unit, make sure to leave space

around the unit for ventilation to improve heat radiation

(at least 30 cm at top, 10 cm at rear, and 10 cm at each

side).

WARNING

Slots and openings in the cabinet are provided for

ventilation to ensure reliable operation of the product,

and to protect it from overheating. To prevent fire

hazard, the openings should never be blocked or

covered with items (such as newspapers, table-cloths,

curtains) or by operating the equipment on thick carpet

or a bed.

D3-4-2-1-7b*_A1_En

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean

that used electrical and electronic products and batteries should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old products and used batteries,

please take them to applicable collection points in accordance with your national

legislation.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries,

please contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

These symbols are only valid in the European Union.

For countries outside the European Union:

If you wish to discard these items, please contact your local authorities or dealer and

ask for the correct method of disposal.

K058a_A1_En

Symbol examples

for batteries

Symbol for

equipment

Pb

CAUTION

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

D3-4-2-1-1_B1_En

A70_SYXE8_0728.book 2 ページ２０１５年７月２８日　火曜日　午後３時５４分

3

CAUTION

The /I STANDBY/ON switch on this unit will not

completely shut off all power from the AC outlet.

Since the power cord serves as the main disconnect

device for the unit, you will need to unplug it from the

AC outlet to shut down all power. Therefore, make

sure the unit has been installed so that the power

cord can be easily unplugged from the AC outlet in

case of an accident. To avoid fire hazard, the power

cord should also be unplugged from the AC outlet

when left unused for a long period of time (for

example, when on vacation).

D3-4-2-2-2a*_A1_En

Operating Environment

Operating environment temperature and humidity:

+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH

(cooling vents not blocked)

Do not install this unit in a poorly ventilated area, or in

locations exposed to high humidity or direct sunlight (or

strong artificial light)

D3-4-2-1-7c*_A1_En

This product is for general household purposes. Any

failure due to use for other than household purposes

(such as long-term use for business purposes in a

restaurant or use in a car or ship) and which requires

repair will be charged for even during the warranty

period.

K041_A1_En

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the

plug by tugging the cord and never touch the power

cord when your hands are wet as this could cause a

short circuit or electric shock. Do not place the unit, a

piece of furniture, etc., on the power cord, or pinch the

cord. Never make a knot in the cord or tie it with other

cords. The power cords should be routed such that they

are not likely to be stepped on. A damaged power cord

can cause a fire or give you an electrical shock. Check

the power cord once in a while. When you find it

damaged, ask your nearest PIONEER authorized

service center or your dealer for a replacement.

S002*_A1_En

Thank you for buying this Pioneer

product.

Please read through these operating instructions so that

you will know how to operate your model properly. After

you have finished reading the instructions, put them in a

safe place for future reference.

Contents

01 Before you start

What’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . .4

Loading the batteries in the remote control . . . . . .4

Using the remote control. . . . . . . . . . . . . . . . . . . . .4

Installing the amplifier. . . . . . . . . . . . . . . . . . . . . .4

02 Connecting up

Making cable connections. . . . . . . . . . . . . . . . . . .5

About “Bi-wiring” . . . . . . . . . . . . . . . . . . . . . . . . . .5

Connecting speaker cables . . . . . . . . . . . . . . . . . .6

Connecting audio cables . . . . . . . . . . . . . . . . . . . .6

Connecting to the balanced input terminals (A-70DA

only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Digital audio input connections. . . . . . . . . . . . . . .7

Using a USB cable to connect to a computer . . . .7

Using centralized control with other Pioneer

components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

03 Controls and displays

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . .10

04 Operation

Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Set the power to Standby. . . . . . . . . . . . . . . . . . . .11

When using the unit as a power amplifier . . . . . . .11

Playing music from a digital audio component . . .11

Making an audio recording . . . . . . . . . . . . . . . . .12

To set for automatic standby status (Auto Power

Down) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Restoring all the settings to the factory default

settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

05 Using the USB DAC function

Install the driver. . . . . . . . . . . . . . . . . . . . . . . . . .13

Playing music from a computer. . . . . . . . . . . . . .13

06 Additional information

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . .14

About the USB DAC function . . . . . . . . . . . . . . . .15

Cleaning the unit . . . . . . . . . . . . . . . . . . . . . . . . .15

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .16

A70_SYXE8_0728.book 3 ページ２０１５年７月２８日　火曜日　午後３時５４分

01 Before you start

4

En

Chapter 1:

Before you start

What’s in the box

Please confirm that the following accessories are in the

box when you open it.

•Remote control

• AAA/IEC R03 dry cell batteries x2

• Short pin plug x 2

(At time of purchase, these plugs have been factory

installed in the rear panel’s PHONO IN terminals.)

• Power cord (Length: 1.8 m)

• Warranty card

• Caution sheet (To first-time users)

• Operating instructions (This document)

WARNING

• Store small parts out of the reach of children and

infants. If accidentally swallowed, contact a doctor

immediately.

Note

• Illustrations featured in the Operating Instructions

may have been modified or simplified for ease of

explanation, and may therefore differ from the

actual product appearance.

• The illustrations used here are mainly of the A-

70DA.

Loading the batteries in the remote

control

1 Open the rear lid.

2 Insert the new batteries, matching the

polarities as indicated inside the case.

3 Close the rear lid.

The batteries included with the unit have been provided

to allow you check product operation and may not last

long. We recommend using alkaline batteries that have

a longer life.

WARNING

• Do not use or store batteries in direct sunlight or

other excessively hot place, such as inside a car or

near a heater. This can cause batteries to leak,

overheat, explode or catch fire. It can also reduce

the life or performance of batteries.

Caution

Incorrect use of batteries may result in such hazards as

leakage and bursting. Observe the following

precautions:

• When inserting the batteries, make sure not to

damage the springs on the battery’s  terminals.

This can cause batteries to leak or overheat.

• Do not use any batteries other than the ones

specified. Also, do not use a new battery together

with an old one.

• When loading the batteries into the remote control,

set them in the proper direction, as indicated by the

polarity marks ( and ).

• Do not heat batteries, disassemble them, or throw

them into flames or water.

• Batteries may have different voltages, even if they

are the same size and shape. Do not use different

types of batteries together.

• To prevent leakage of battery fluid, remove the

batteries if you do not plan to use the remote

control for a long period of time (1 month or more).

If the fluid should leak, wipe it carefully off the

inside of the case, then insert new batteries. If a

battery should leak and the fluid should get on your

skin, flush it off with large quantities of water.

• When disposing of used batteries, please comply

with governmental regulations or environmental

public institution’s rules that apply in your country/

area.

1

2

3

Using the remote control

The remote has a range of about 7 m at an angle of about

30º from the remote sensor.

Keep in mind the following when using the remote

control:

• Make sure that there are no obstacles between the

remote and the remote sensor on the unit.

• Remote operation may become unreliable if strong

sunlight or fluorescent light is shining on the unit’s

remote sensor.

• Remote controllers for different devices can

interfere with each other. Avoid using remotes for

other equipment located close to this unit.

• Replace the batteries when you notice a fall off in

the operating range of the remote.

Installing the amplifier

When installing this unit, make sure to put it on a level

and stable surface.

• Don’t install it on the following places:

– on a color TV (the screen may distort)

– near a cassette deck (or close to a device that

gives off a magnetic field). This may interfere with

the sound.

– in direct sunlight

– in damp or wet areas

– in extremely hot or cold areas

– in places where there is vibration or other

movement

– in places that are very dusty

– in places that have hot fumes or oils (such as a

kitchen)

• Do not mount the unit on a sofa or other object or

material with absorbent qualities, since sound

quality may be adversely affected.

7 m

30 °

A70_SYXE8_0728.book 4 ページ２０１５年７月２８日　火曜日　午後３時５４分

Connecting up 02

5

En

English

DeutschFrançais

Nederlands

Italiano Español Русский

Chapter 2:

Connecting up

Making cable connections

Caution

• Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.

• Connect the power cord after all the connections between devices have been completed.

NORMAL

INVERSION

PHASE

LINE2

LINE1

USB

COAXIAL

PHONO

(MM/MC)

SIGNAL

GND

NETWORK

SACD/CD

DIGITAL IN

ANALOG IN

OPTICAL

LINE2

OUT

POWER

AMP

DIRECT

BALANCED IN

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

L

R

MENU

iPod





Music>

Extras>

Settings>

Shuffle Songs

Backlight

SOURCE

/I STANDBY/ON

STANDBY

iPod/iPhone

5V 1A

DIRECT Hi-Bit 32 Up Sampling

SOURCE



 



SACD/CD player

Network audio player

PRE OUT jacks on pre-

amplifier or AV amplifier

Speaker system B

Speaker system A

Turntable

Audio device with

balanced output terminals

iPod dock, etc.

Recording device

or other device

Right Left

Right

Left

Power cord

(included)

This unit’s

rear panel

Caution

•The SIGNAL GND terminal is provided to reduce

noise when connecting the unit to components

such as an analog turntable.

•The PHONO IN terminals are factory equipped with

short pin plugs. These should not be removed

except when connecting a turntable. Be sure to

save the short pin plugs in a safe place.

• Do not insert the short pin plugs in any connectors

other than the PHONO IN terminals. Connecting

them to any other terminals may cause

malfunctions.

• Do not connect the PHONO IN terminals to any

component other than a turntable; also, do not

connect to a turntable equipped with built-in

equalizer. An excessively high sound output may be

produced, resulting in damage to your speakers or

other devices.

• The A-50DA’s PHONO IN terminals are designed to

be used only with turntables equipped with MM

(moving-magnet) type cartridges. Turntables

equipped with MC (moving-coil) cartridges cannot

be used.

• Make sure not to bend the cables over the top of

this unit (as shown in the illustration). If this

happens, the magnetic field produced by the

transformers in this unit may cause a humming

noise from the speakers.

• The unit’s POWER AMP DIRECT terminals should

never be connected to any other component’s

connectors except PRE-AMP OUT.

• If your turntable has a grounding wire, secure it to

the ground terminal on this amplifier.

Note

• When connecting a tape cassette deck, playback

noise may be heard, depending on the installation

location. This noise is caused by leakage flux from

the amplifier’s transformer. In this event, change

the installation location, or move the deck farther

from the amplifier.

• iPod is a trademark of Apple Inc., registered in the

U.S. and other countries.

About “Bi-wiring”

This unit can be used with speakers that support bi-

wiring. Be sure to connect the high-frequency and

low-frequency connections correctly.

• During playback, be sure that both the SPEAKERS

A button and SPEAKERS B button are set to ON

(page 8).

Caution

• When using bi-wiring to connect speakers, avoid

adverse affects on the amplifier by being sure to

remove the HIGH and LOW short bars provided

with the speakers. For detailed information, consult

the instructions provided with the speakers.

HIGH

LOW

HIGH

LOW

Speaker system

Left

Speaker system

Right

This unit’s

rear panel

Remove the shorting

bar between the +

and – terminals.

A70_SYXE8_0728.book 5 ページ２０１５年７月２８日　火曜日　午後３時５４分

02 Connecting up

6

En

• When using speakers with removable network

circuits, note that if the network is removed, no

effect will be produced and damage may be caused

to the speaker.

• Another method of connection is to connect the

SPEAKERS A terminals to HIGH and the SPEAKERS

B terminals to LOW (reverse that shown in the

illustration).

Connecting speaker cables

1 Twist the cable cores.

2 Loosen the nut on the

SPEAKERS

terminal, and insert the speaker cable into

the exposed hole in the terminal shaft.

3 Retighten the terminal nut.

Caution

• When using only one set of speaker terminals

(SPEAKERS A or SPEAKERS B), or when utilizing

bi-wiring connections, the speaker used should

have a nominal impedance between 4  and

16 . When using both sets of terminals, the

connected speakers should have nominal

impedance between 8  and 32 . Consult the

instructions accompanying your speakers for

details regarding the impedance value.

• Make sure the positive and negative (+/–) terminals

on the amplifier match those on the speakers.

• These speaker terminals carry HAZARDOUS live

voltage. To prevent the risk of electric shock when

connecting or disconnecting the speaker cables,

disconnect the power cord before touching any

uninsulated parts.

• Make sure that all the bare speaker wire is twisted

together and inserted fully into the speaker

terminal. If any of the bare speaker wire touches the

back panel it may cause the power to cut off as a

safety measure.

Connecting audio cables

Connect the white plug to the left (L) jack, and the red

plug to the right (R) jack. Be sure to insert the plugs fully

into the jacks.

123

10 mm

Left (white)

Right (red)Right (red)

Connecting to the balanced input

terminals (A-70DA only)

Connect the BALANCED IN terminals of the unit to a

SACD player, USB DAC, network player, or other device

with balanced output terminals.

Caution

•The BASS, TREBLE, BALANCE, and LOUDNESS

functions do not work for a device connected to the

BALANCED IN terminals.

The phase may differ depending on the device to be

connected. Use the phase selector switch on the rear

panel of the unit to match the phase.

• Initial setting (No. 2 HOT)

• Settings when polarity changed

(No. 3 HOT)

Note

• For details on the phase of the balanced output

terminals of the device to be connected, refer to the

instruction manual of the device.

• When connecting the unit to a Pioneer player,

match the phase to the initial setting (No. 2 HOT).

LINE2

LINE1

USB

COAXIAL

PHONO

(MM/MC)

SIGNAL

GND

NETWORK

SACD/CD

DIGITAL IN

ANALOG IN

OPTICAL

LINE2

OUT

P.

AMP

DIRECT

BALANCED IN

NORMAL

INVERSION

PHASE

Audio device with

balanced output terminals

Balanced cable

(sold separately)

Balanced cable

(sold separately)

A-70DA’s rear panel

NORMALNORMAL

INVERSIONINVERSION

PHASEPHASE

1 Ground

3 COLD (-)

2 HOT (+)

NORMAL

INVERSION

PHASE

1 Ground

3 HOT (+)

2 COLD (-)

A70_SYXE8_0728.book 6 ページ２０１５年７月２８日　火曜日　午後３時５４分

Connecting up 02

7

En

English

DeutschFrançais

Nederlands

Italiano Español Русский

Digital audio input connections

If you connect the DIGITAL IN terminal of the unit and

the digital audio output of a digital audio device with a

separately sold digital cable, you can play the audio of

the digital audio device with the unit.

For details on the output of audio input to the DIGITAL

IN terminal, refer to page 11.

Note

• Digital signal formats that can be input to this unit

include linear PCM signals with sampling rate and

quantitative bits up to 192 kHz/32 bits. (Depending

on the connected device and environment,

operation may not be successful).

Using a USB cable to connect to a

computer

If a USB cable (sold separately) is used to connect this

unit’s DIGITAL IN USB terminal to a computer’s USB

port, music files located on the computer can be played

through this unit.

For more information regarding the output of audio

signals input to the DIGITAL IN USB terminal, consult

page 13.

Important

• A dedicated driver needs to be installed on your

computer (page 13).

Note

• This unit cannot be used to play audio files from a

computer unless Media Player is installed on the

connected computer.

LINE2

LINE1

USB

COAXIAL

DIGITAL IN

G

IN

ANALOG IN

OPTICAL

LINE2

OUT

C

ED IN

BALANCED IN

NORMAL

INVERSION

PHASE

DIGITAL OUT

COAXIAL

DIGITAL OUT

OPTICAL

Digital audio

equipment, etc.

Coaxial digital audio cable

(sold separately)

A-70DA’s rear panel

Optical digital audio cable

(sold separately)

Digital audio

equipment, etc.

LINE2LINE2

LINE1LINE1

USBUSB

COAXIALCOAXIAL

DIGITAL INDIGITAL IN

G INANALOG IN

OPTICALOPTICAL

LINE2LINE2

OUT OUT

CED INBALANCED IN

NORMALNORMAL

INVERSIONINVERSION

PHASEPHASE

USB

USB cable

(sold separately)

A-type

B-type

PC

A-70DA’s rear panel

Using centralized control with other

Pioneer components

Multiple Pioneer components equipped with CONTROL

IN/OUT jacks can be connected to the unit, allowing

centralized control of the components via the remote

sensor on the unit. This also allows remote control of

components not equipped with a remote sensor, or

installed in places where the component’s remote

sensor cannot be accessed.

Note

• For connections use a commercially available

monaural miniplug cord (without resistor).

• When connecting the CONTROL IN/OUT jacks,

commercially available audio cords must also be

used to make analog connections. Merely

connecting the CONTROL IN/OUT jacks alone will

not allow proper system control.

• When a control cord is connected to the unit’s

CONTROL IN jack, the unit cannot be controlled by

pointing the remote control at the unit (the remote

sensor is automatically disabled).

Plugging in

Important

• When going on a trip or otherwise not using the

unit for an extended period, always disconnect the

power cord from its outlet. Note that various

internal settings will not be lost even if the power

cord is disconnected from its outlet for an extended

time.

• If it is necessary to detach the power cord, first be

sure to press the 

/I

STANDBY/ON button on the

front panel of the unit so the unit is turned OFF

before detaching the cord.

Caution

• The use of a power cord other than the one provided

will invalidate the warranty, since Pioneer will not

be responsible for any damage incurred. (The

power cord provided with the unit has a rated

current capacity of 10 A.)

• Do not use any power cord other than the one

supplied with this unit.

• Do not use the supplied power cord for any purpose

other than that described below.

After you’ve finished making all connections, plug the

unit into an AC outlet.

1 Plug the supplied power cord into the

AC IN

socket on the rear panel of the unit.

2 Plug the other end into an AC outlet.

IN

OUT

CONTROL

Other Pioneer

component equipped

with CONTROL IN/

OUT jacks

To other Pioneer

component

equipped with

CONTROL IN jack

A-70DA

Aim remote control

at the sensor on the

unit.

Remote

control

To AC outlet

This unit’s rear panel

Power cord

(included)

A70_SYXE8_0728.book 7 ページ２０１５年７月２８日　火曜日　午後３時５４分

03 Controls and displays

8

En

Chapter 3:

Controls and displays

Front panel

1



/I

STANDBY/ON

Switches the amplifier between off and on.

When power is turned on, the power indicator in the

center of the button will light.

2

STANDBY/APD

indicator

When power is set to standby, the indicator lights red.

When the Auto Power Down (APD) function is on, the

indicator lights green (page 12).

3

SPEAKERS A

button/indicator

Use this button to listen to the speaker system

connected to SPEAKERS A terminals.

On : The indicator lights. Sound is heard from the

speaker system.

Off : The indicator goes off. No sound is heard from the

speaker system.

4

SPEAKERS B

button/indicator

Use this button to listen to the speaker system

connected to SPEAKERS B terminals.

On : The indicator lights. Sound is heard from the

speaker system.

Off : The indicator goes off. No sound is heard from the

speaker system.

5

LOUDNESS

button/indicator

Use when listening at low volume levels.

On : The indicator lights: Boosts low and high

frequencies to give added punch to playback even at a

low volume level.

Off : The indicator goes off: Should normally be left in

this position.

• This button does not operate when the DIRECT

button is in the on position.

• When sound volume is raised, the amount of

change produced by the LOUDNESS circuit is

reduced.

A-70DA

31

6

2 54

7

14 1612

9

10 11 13 15

8

6 Remote sensor

Receives the signals from the remote control (page 4).

7

PHONES

jack

Use to connect headphones (when connected, there is

no sound output from the speakers). No sound is

produced when the POWER AMP DIRECT button is ON.

8 DIRECT button/indicator

On : The indicator lights: When this button is set to ON,

sound signals are output directly, without being passed

through the various adjustment circuits (BASS, TREBLE,

BALANCE, LOUDNESS). This allows reproduction of the

signals with greater fidelity, but it disables any settings

made with the BASS, TREBLE, BALANCE or LOUDNESS

controls. When a device connected to the BALANCED IN

terminals is played, DIRECT turns on and cannot be

turned off.

Off : The indicator goes off: The signal passes through

the various frequency adjusting circuits. When the

indicator is OFF, adjustments can be made with the

BASS, TREBLE, BALANCE, and LOUDNESS controls.

9

BASS

tone control

Use to adjust the low-frequency tone. The center position

is the flat (normal) position. When turned to the right,

low-frequency tones are emphasized; when turned to the

left, low-frequency tones are de-emphasized.

• This button does not operate when the DIRECT

button is in the on position.

10

TREBLE

tone control

Use to adjust the high-frequency tone. The center

position is the flat (normal) position. When turned to the

right, high-frequency tones are emphasized; when

turned to the left, high-frequency tones are de-

emphasized.

• This button does not operate when the DIRECT

button is in the on position.

11

BALANCE

control

Should normally be left in the center position. Adjust

balance if the sound is louder from one of the speakers.

If the right side is louder, turn toward the L (left) position

and if the left side is louder, turn toward the R (right)

position.

• This button does not operate when the DIRECT

button is in the on position.

12

ATTENUATOR

button (A-70DA only)

Press when you wish to make fine adjustments to the

sound volume when playing at very low sound volume

levels.

13 VOLUME control

Use to adjust the volume level. (Also allows adjustment

of the headphone sound volume.)

14

CARTRIDGE

select switch (A-70DA only)

Select the type of cartridge used with your turntable.

15

POWER AMP DIRECT

button/indicator

Press this button when the unit is to be used as a power

amplifier (page 11).

16

INPUT SELECTOR

knob/indicators

Turn the knob clockwise or counterclockwise so that the

indicator lights for your desired input source. Turning

the knob clockwise causes the lit indicator to right.

Turning counterclockwise causes it to left. When the

remote control’s MUTE button is pressed to mute the

sound, the indicator for the input source selected with

the INPUT SELECTOR knob flashes.

A70_SYXE8_0728.book 8 ページ２０１５年７月２８日　火曜日　午後３時５４分

Controls and displays 03

9

En

English

DeutschFrançais

Nederlands

Italiano Español Русский

Rear panel

See pages 5-7 for details regarding connections.

1

PHONO IN (MM/MC)

terminals

(A-70DA)

PHONO IN (MM) terminals (A-50DA)

2

POWER AMP DIRECT

IN

terminals

When using the unit as a power amplifier, connect the

pre-amplifier here (page 11).

3 BALANCED

IN

terminals (A-70DA only)

4 Phase selector switch (A-70DA only)

Switches the phase of the BALANCED IN terminals.

5

DIGITAL IN USB

terminal

6

SPEAKERS A

terminals (Right channel)

7

SPEAKERS B

terminals (Right channel)

8

SPEAKERS B

terminals (Left channel)

9

SPEAKERS A

terminals (Left channel)

10 GND (Turntable ground) terminal

This ground terminal is designed to help reduce noise

when a turntable is connected. It is not a safety ground.

11

NETWORK

IN

terminals

12

SACD/CD

IN

terminals

13

LINE

1 terminals

14

LINE

2

IN/OUT

terminals

15

DIGITAL IN OPTICAL

terminal

16

DIGITAL IN COAXIAL

terminal

17

CONTROL IN/OUT

jack

18

AC IN

jack

Connect power cord to here and an AC wall socket.

LINE2

LINE1

USB

COAXIAL

PHONO

(MM/MC)

SIGNAL

GND

NETWORK

SACD/CD

DIGITAL IN

ANALOG IN

OPTICAL

LINE2

OUT

POWER

AMP

DIRECT

BALANCED IN

NORMAL

INVERSION

PHASE

21 2 2724

2

10 11 15 16 1817

29

3

28

12 13

5 26

14

A70_SYXE8_0728.book 9 ページ２０１５年７月２８日　火曜日　午後３時５４分

03 Controls and displays

10

En

Remote control

STANDBY/ON

A

B

APD

1

8

10

9

12

11

13

2

3

4

6

4

7

5

1

 STANDBY/ON

Switches the amplifier between standby and on.

2 Input selector buttons

Press to select an input source. These select the

component connected to the corresponding input on the

rear panel.

•The BALANCED button cannot be used with the A-

50DA.

3 SACD PLAYER control buttons

Use to control Pioneer SACD player.

4 NETWORK AUDIO PLAYER control

buttons

Use to control Pioneer network audio player.

5

LOUDNESS

Use to set the loudness circuit ON/OFF (page 8).

6

MUTE

Mutes/unmutes the sound.

7

DIRECT

Press to access Direct listening (page 8).

8

DIMMER

This button allows the illumination of the unit's front

panel indicators to be set in three levels (does not affect

the STANDBY indicator).

9

POWER AMP DIRECT

Press this button when the unit is to be used as a power

amplifier (page 11).

10

SPEAKERS A

Use this button to listen to the speaker system

connected to SPEAKERS A terminals.

11

SPEAKERS B

Use this button to listen to the speaker system

connected to SPEAKERS B terminals.

12

VOLUME +/–

Use to set the listening volume.

13

APD

Use to set the Auto Power Down function to ON/OFF

(page 12).

A70_SYXE8_0728.book 10 ページ２０１５年７月２８日　火曜日　午後３時５４分

Operation 04

11

En

English

DeutschFrançais

Nederlands

Italiano Español Русский

Chapter 4:

Operation

Playback

1 Turn on the power of the playback

component.

2 Turn power ON to the unit.

• If the unit is in the standby mode, press the remote

control’s  STANDBY/ON button.

3 Select the source you want to playback.

Select the playback component.

• When using the front panel controls, rotate the

INPUT SELECTOR knob.

• In the case of the A-70DA, if PHONO is selected,

use the CARTRIDGE select switch to designate the

type of cartridge used with your turntable, either

MM () or MC ().

4 Start playback of the component you

selected in step 1.

5 Adjust playback volume with

VOLUME

control.

6 Adjust the tone to your preference using

the

BASS

and

TREBLE

controls, and

LOUDNESS

button.

If the DIRECT button has been set to ON, these controls

are disabled.

3566

62

MENU

iPod





Music>

Extras>

Settings>

Shuffle Songs

Backlight

SOURCE

/I STANDBY/ON

STANDBY

iPod/iPhone

5V 1A

DIRECT Hi-Bit 32 Up Sampling

SOURCE



 



SACD/CD player

Network audio player

Turntable

iPod dock, etc.

Recording device

or other device

Playback

Audio device with

balanced output terminals

VOLUME

Caution

•The BASS, TREBLE, BALANCE, and LOUDNESS

functions do not work for a device connected to the

BALANCED IN terminals.

Set the power to Standby

1 Press the remote control’s

 STANDBY/

ON

button.

The next time you wish to turn on the power, press the

remote control’s  STANDBY/ON button.

• If the front panel’s /I STANDBY/ON button is

pressed, the power will be turned off. In this case, if

the power is off, pressing the remote control’s

 STANDBY/ON button will not turn on the power.

To turn on the power again, press the front panel’s

/I STANDBY/ON button.

When using the unit as a power amplifier

When a pre-amplifier is connected to the unit’s POWER

AMP DIRECT IN terminals, the unit can be used as a

power amplifier.

1 Press the

POWER AMP DIRECT

button

on the remote control or front panel of the

unit.

The POWER AMP DIRECT indicator will light.

Caution

•When the POWER AMP DIRECT indicator is

lighted, operations change as follows:

– The unit’s front-panel VOLUME, BASS, TREBLE,

and BALANCE controls are disabled. These

adjustments are controlled by the component

connected to the unit’s POWER AMP DIRECT IN

terminals.

–The LOUDNESS button and ATTENUATOR

button (A-70DA only) are disabled.

–When the POWER AMP DIRECT indicator is

lighted, sound volume from the unit will

automatically be fixed at its maximum output.

When using this unit as a power amplifier,

check the output level of the component

connected to the POWER AMP DIRECT IN

terminals and set it to a low level as appropriate

before turning on the POWER AMP DIRECT

indicator. If the sound volume of the component

connected to the POWER AMP DIRECT IN

terminals is initially set to a high output level,

loud sound may suddenly be output when the

POWER AMP DIRECT indicator lights.

– Sound is not produced from the PHONES jack

and LINE 2 OUT terminals.

• For more information, consult the operating

instructions for the component connected to the

unit’s POWER AMP DIRECT IN terminals.

Playing music from a digital audio

component

Output the digital audio input to the DIGITAL IN

COAXIAL or OPTICAL terminal.

1 Make a digital input connection.

• See Digital audio input connections on page 7.

2 Switch to the

COAXIAL

or

OPTICAL

input.

Each press of the COAXIAL/OPTICAL button on the

remote control switches the input alternately.

• When using the front panel controls, rotate the

INPUT SELECTOR knob.

• Sound is produced from the LINE 2 OUT terminals.

Note

• Digital signal formats that can be input to this unit

include linear PCM signals with sampling rates and

quantitative bits up to 192 kHz/32 bits (Depending

on the connected device and environment,

operation may not be successful).

A70_SYXE8_0728.book 11 ページ２０１５年７月２８日　火曜日　午後３時５４分

04 Operation

12

En

Making an audio recording

You can make an audio recording from any audio source connected to the amplifier.

1 Select the source you want to record. 2 Start recording, then start playback of

the source component.

Caution

• Confirm that the short pin plugs are not inserted in

the LINE 2 OUT terminals, since malfunction will

result if they are inserted.

• Audio connected to the following terminals cannot

be output from the LINE 2 OUT terminals.

-

LINE 2 IN

-

BALANCED IN

-

POWER AMP DIRECT IN

1

MENU

iPod





Music>

Extras>

Settings>

Shuffle Songs

Backlight

SOURCE

/I STANDBY/ON

STANDBY

iPod/iPhone

5V 1A

DIRECT Hi-Bit 32 Up Sampling

SOURCE



 



SACD/CD player

Network audio player

Turntable

iPod dock, etc

Audio recording component

(CD recorder, tape deck, etc.)

Playback

Recording

To set for automatic standby status (Auto Power Down)

This function automatically switches the unit to standby mode if no signal or switch operation is detected for 30

minutes.

1 If the unit’s power is ON, press the

APD

button on the remote control.

When this condition is set to ON, the STANDBY/APD indicator on the unit’s front panel will light green. Press the

buttons again to disable the setting.

• This setting can also be made by pressing the front panel LOUDNESS button and POWER AMP DIRECT button

simultaneously and holding them depressed for 3 seconds.

• The factory default setting is ON.

•Rotating the TREBLE, BASS, BALANCE, or VOLUME controls will not be counted as a control operation for

purposes of resetting the Automatic Power-Down 30-minute timer.

Note

• Depending on the connected devices, the unit may not be automatically powered down for reasons such as there

being a lot of noise.

Restoring all the settings to the factory default settings

1 When power is in standby mode, hold the front-panel’s SPEAKERS A button and

POWER AMP DIRECT button depressed simultaneously for five seconds.

2 Turn power ON to the unit.

A70_SYXE8_0728.book 12 ページ２０１５年７月２８日　火曜日　午後３時５４分

Using the USB DAC function 05

13

En

English

DeutschFrançais

Nederlands

Italiano Español Русский

Chapter 5:

Using the USB DAC function

Install the driver

• To use the DIGITAL IN USB terminal to play back

music files on the computer with the unit, you need

to install a dedicated driver on your computer. For

details, refer to the Pioneer website. The instruction

manual also contains information regarding the

installation procedure and computer settings, so

refer to the instruction manual as well.

Playing music from a computer

Use this function to play digital audio input to the unit's

rear panel DIGITAL IN USB port.

1 Connect the unit to a computer via USB

cable (page 7).

2Press

USB

to select

DIGITAL IN USB

as

the input source.

• When using the front panel controls, rotate the

INPUT SELECTOR knob.

• Sound is produced from the LINE 2 OUT terminals.

3 Begin playback on the computer.

Note

• When the unit and a computer are connected to

play back audio with a USB cable, the unit can

input the following signals:

Linear PCM

– Quantitative bits: 16 bit, 24 bit, 32 bit

– Sampling frequency: 44.1 kHz, 48 kHz, 88.2 kHz,

96 kHz, 176.4 kHz, 192 kHz, 352.8 kHz, 384 kHz

DSD

– Sampling frequency: 2.8 MHz, 5.6 MHz, 11.2

MHz

• Playback cannot be controlled from this unit during

use of this function; use your computer to control

playback.

• When disconnecting the USB cable, always stop

playback on the computer first.

• Sound may not be produced if your computer does

not support USB 2.0 HS.

• This unit does not support use of a USB hub.

Always use a USB cable to connect the unit directly

to the computer.

A70_SYXE8_0728.book 13 ページ２０１５年７月２８日　火曜日　午後３時５４分

06 Additional information

14

En

Chapter 6:

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with

this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other

components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks

listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug

from the outlet and insert again to return to normal operating conditions.

Problem Remedy

The power does not turn on. • Is the power plug disconnected from the power outlet? Connect the power plug

correctly to its outlet (page 7).

•Is the power cord disconnected from the AC IN connector? Connect the power cord

correctly (page 7).

Power turns off. •Is the Auto Power Down function turned ON? If you do not want the power to turn off

automatically, disable the Auto Power Down function (page 12).

The power turned off and the

STANDBY/APD

indicator is flashing

three times repeatedly.

•The protection circuit has been activated. This condition will result if a very low-

frequency sound is played at a high sound volume level.

- Turn the power OFF and wait for at least one minute, then turn the power ON again;

play the music at a lower sound volume level.

- After restarting the power, if the

STANDBY/APD

indicator flashes four times, it

indicates the receiver channels are malfunctioning. Disconnect the power cord and

consult your dealer or nearest Pioneer service station.

The power turned off and the

STANDBY/APD

indicator is flashing

once every two seconds.

•The unit’s internal temperature has risen and the safety circuit has operated.

- Turn power OFF and wait for a minute or more, allowing the unit’s temperature to

cool before turning the power ON again.

- Install the unit in a location with better ventilation.

- Confirm that the unit is installed correctly; if the unit is turned on again without

being allowed to cool, the same symptoms may appear (page 4).

The power turned off and the

STANDBY/APD

indicator is flashing

twice repeatedly.

•Are you using speakers with impedance values not supported by this unit? Confirm

the speaker’s nominal impedance value (page 6).

•Are any speaker cables loose from the

SPEAKERS

terminals and touching other

wires or the surface of the rear panel? Disconnect the power cord and reconnect the

speaker cables correctly (page 6).

The power turned off and the

STANDBY/APD

indicator is flashing

six times repeatedly.

•The protection circuit has been activated. This condition will result if a very high-

frequency sound is played at a high sound volume level.

- Lower the sound volume and try playing again.

- If the same symptom appears when the power is turned OFF then ON again, the

unit’s circuitry may be damaged. Disconnect the power cord and consult your

dealer or nearest Pioneer service station.

The

STANDBY/APD

indicator is

flashing four times, five times, or

seven times repeatedly and the power

does not turn on.

•The unit’s circuitry is damaged. Disconnect the power cord and consult your dealer

or nearest

Pioneer authorized service center

.

No sound is output when a function is

selected.

•A connection cable is disconnected or connected improperly. Check your

connections (page 5).

•Connectors or pin plugs on a cable are dirty. Wipe off any dirt from connectors and

pin plugs.

•Confirm that the unit’s input selector is set to the desired playback component. Set

selector correctly (page 11).

•Press

MUTE

on the remote control to turn muting off (page 10).

No sound from one speaker. •Are the connection cables or speaker cables disconnected on one side? Reconnect

securely (page 5).

Can’t operate the remote

control.

•Replace the battery (page 4).

•Operate within 7 m, 30° of the remote sensor on the front panel (page 4).

•Remove the obstacle or operate from another position.

•Avoid exposing the remote sensor on the front panel to direct light.

•Is the control cord for one component connected improperly? Confirm correct

connections (page 7).

Can’t change input source. •Check whether

POWER AMP DIRECT

function is ON. If so, press the front panel’s

POWER AMP DIRECT

button to turn the function OFF (page 11).

Sound of the digital input is not

output.

•The digital format of the output device is not supported. If the output device is set to

an audio signal (Dolby Digital, DTS, etc.) other than PCM, change the setting to PCM.

Sound of the digital input is not output

when playing back a SACD.

•Many SACD players (including Blu-ray players and DVD players compatible with

SACD playback) are not designed to output digital when playing back a SACD. Check

the specifications of the SACD player. Alternatively, play back the audio with an analog

connection.

No sound is heard when a linear PCM

signal with frequency of 96 kHz or

more is input to the

DIGITAL IN

COAXIAL

terminal.

•Sound may not be output properly depending on the digital coaxial cable used; try

replacing the cable (sold separately) with another.

Problem Remedy

A70_SYXE8_0728.book 14 ページ２０１５年７月２８日　火曜日　午後３時５４分

Additional information 06

15

En

English

DeutschFrançais

Nederlands

Italiano Español Русский

About the USB DAC function

Important

• For details on the computer settings, also refer to the instruction manual of the driver software available on the

Pioneer website.

Problem Remedy

Music files on a computer connected

via USB cannot be played back.

•To connect a computer and the unit via USB and then play back music files input via

USB, you need to download a dedicated driver from the Pioneer website and then

install it on the computer. Consult the Pioneer website for instructions on installing the

driver.

No sound is produced when

attempting to play files on a computer.

•Are volume settings correct for the OS and application program? Raise the volume

settings as required.

•Is the OS audio output set to MUTE? Cancel the MUTE setting.

•Are multiple applications running simultaneously? Try closing applications that are

not in use.

•Has the audio output been set properly within the OS or application used? For audio

device select

“

Pioneer A-70DA A-50DA USB Audio

”

.

No sound is produced when using a

USB input.

•Is another device selected in the computer settings or is the sound muted in the

computer settings? Check the computer settings.

•Is the unit connected correct? Is the unit detected by the computer? If the unit is

switched to the USB input after it is connected to a computer, other than unit may be

selected in the sound settings of the computer. If that happens, select the unit again.

Also check the connection.

•Are the file format, operating system, and software supported? Check the supported

operating systems, software, and file sampling frequencies.

•Is the dedicated driver installed on the computer? A dedicated driver needs to be

installed on the computer. For details, refer to the Pioneer website.

Non-musical computer sounds from

the USB input are audible.

•Depending on the computer settings, the startup sound, error sounds, and other

sounds of the computer may be played back from the unit. Check the computer

settings.

When using a source other than USB

input, music files on the computer

can't be played.

•When the input is other than USB, the unit is recognized from the computer. Switch

the input to USB and then select the unit in the sound settings of the computer again.

If 384 kHz or 356 kHz is set in the

sound settings of the computer, a

certain browser or software is

terminated and the audio plays back

without sound.

•The browser or software may not support 384 kHz or 356 kHz. Check the

specifications of the browser or software.

Cleaning the unit

• Use a polishing cloth or dry cloth to wipe off dust

and dirt.

• When the surface is dirty, wipe with a soft cloth

dipped in some neutral cleanser diluted five or six

times with water, and wrung out well, and then

wipe again with a dry cloth. Do not use furniture

wax or cleansers.

• Never use thinners, benzine, insecticide sprays or

other chemicals on or near this unit, since these

will corrode the surface.

A70_SYXE8_0728.book 15 ページ２０１５年７月２８日　火曜日　午後３時５４分

06 Additional information

16

En

Specifications

Amplifier section

Power output specification is for when power supply is 230 V.

• Continuous power output (both

channels driven at 20 Hz to 20 kHz)

A-70DA/A-50DA. . . . . . . . . . . . . . . . . . . . . . .90 W + 90 W

(THD 0.5 %, 4 )

A-70DA/A-50DA. . . . . . . . . . . . . . . . . . . . . . .65 W + 65 W

(THD 0.5 %, 8 )

Audio section

• Input terminals (sensitivity/impedance)

BALANCED . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/82 k

SACD/CD, NETWORK, LINE 1, LINE 2 . . . 200 mV/50 k

POWER AMP DIRECT. . . . . . . . . . . . . . . . . . . . .1 V/10 k

PHONO (MM) . . . . . . . . . . . . . . . . . . . . . . . 2.8 mV/50 k

PHONO (MC). . . . . . . . . . . 0.24 mV/100 A-70DA only

COAXIAL . . . . . . . . . . . . . . . . . . . . . . . . . 500 mVp-p/75 

• Output (Level/Impedance)

LINE 2 OUT . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/2.2 k

• Frequency response

SACD/CD, NETWORK, LINE 1, LINE 2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hz to 50 kHz ±3 dB*

• RIAA DEVIATION

PHONO (MM) . . . . . . . . . . . . . 20 Hz to 20 kHz ±0.5 dB*

PHONO (MC)

. . . . . . . . . . . . . 20 Hz to 20 kHz ±0.5 dB*A-70DA only

* Measured with DIRECT button switched on.

• Tone control

Bass . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 10 dB (100 Hz)

Treble . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 10 dB (10 kHz)

• Signal-to-Noise Ratio (IHF SHORTED,

A-NETWORK)

SACD/CD, NETWORK, LINE 1, LINE 2 . . . . . . . . 101 dB*

PHONO (MM, 5 mV input) . . . . . . . . . . . . . . . . . . . 89 dB*

PHONO (MC, 0.5 mV input) . . . . . .74 dB*A-70DA only

* Measured with DIRECT button switched on.

• Guaranteed impedance

A, B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  to 16 

A+B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  to 32 

Bi-wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  to 16 

Miscellaneous

Power requirements

. . . . . . . . . . . . . . . . . . . . . . . . . . AC 220 V to 230 V, 50 Hz

Power consumption

A-70DA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 W

A-50DA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 W

In standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 W

Dimensions

A-70DA. . . . . 435 mm (W) x 141.5 mm (H) x 370 mm (D)

A-50DA. . . . . 435 mm (W) x 138.5 mm (H) x 368 mm (D)

Weight (without package)

A-70DA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.2 kg

A-50DA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11.2 kg

Accessories

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

AAA/IEC R03 dry cell batteries . . . . . . . . . . . . . . . . . . . . 2

Short pin plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Power cord

Warranty card

Caution sheet

Operating instructions (This document)

Note

• Specifications and the design are subject to

possible modifications without notice, due to

improvements.

• Corporation and product names mentioned herein

are trademarks or registered trademarks of the

respective corporations.

• “Pioneer” is a trademark of Pioneer Corporation,

and is used under license.

A70_SYXE8_0728.book 16 ページ２０１５年７月２８日　火曜日　午後３時５４分

Additional information 06

17

En

English

DeutschFrançais

Nederlands

Italiano Español Русский

A70_SYXE8_0728.book 17 ページ２０１５年７月２８日　火曜日　午後３時５４分

AVERTISSEMENT

Cet appareil n’est pas étanche. Pour éviter les risques

d’incendie et de décharge électrique, ne placez près de

lui un récipient rempli d’eau, tel qu’un vase ou un pot

de fleurs, et ne l’exposez pas à des gouttes d’eau, des

éclaboussures, de la pluie ou de l’humidité.

D3-4-2-1-3_A1_Fr

AVERTISSEMENT

Pour éviter les risques d’incendie, ne placez aucune

flamme nue (telle qu’une bougie allumée) sur

l’appareil.

D3-4-2-1-7a_A1_Fr

PRÉCAUTION DE VENTILATION

Lors de l’installation de l’appareil, veillez à laisser un

espace suffisant autour de ses parois de manière à

améliorer la dissipation de chaleur (au moins 30 cm sur

le dessus, 10 cm à l’arrière et 10 cm de chaque côté).

AVERTISSEMENT

Les fentes et ouvertures du coffret sont prévues pour la

ventilation, pour assurer un fonctionnement stable de

l’appareil et pour éviter sa surchauffe. Pour éviter les

risques d’incendie, ne bouchez jamais les ouvertures et

ne les recouvrez pas d’objets, tels que journaux, nappes

ou rideaux, et n’utilisez pas l’appareil posé sur un tapis

épais ou un lit.

D3-4-2-1-7b*_A1_Fr

K058a_A1_Fr

Pb

Information à destination des utilisateurs sur la collecte et l’élimination des

équipements et batteries usagés

Ces symboles qui figurent sur les produits, les emballages et/ou les documents

d’accompagnement signifient que les équipements électriques et électroniques et

batteries usagés ne doivent pas être jetés avec les déchets ménagers et font l’objet

d’une collecte sélective.

Pour assurer l’enlèvement et le traitement appropriés des produits et batteries

usagés, merci de les retourner dans les points de collecte sélective habilités

conformément à la législation locale en vigueur.

En respectant les circuits de collecte sélective mis en place pour ces produits, vous

contribuerez à économiser des ressources précieuses et à prévenir les impacts

négatifs éventuels sur la santé humaine et l’environnement qui pourraient résulter

d’une mauvaise gestion des déchets.

Pour plus d’information sur la collecte et le traitement des produits et batteries

usagés, veuillez contacter votre municipalité, votre service de gestion des déchets

ou le point de vente chez qui vous avez acheté ces produits.

Ces symboles ne sont valables que dans les pays de l’Union Européenne.

Pour les pays n’appartenant pas à l’Union Européenne :

Si vous souhaitez jeter ces articles, veuillez contacter les autorités ou revendeurs

locaux pour connaître les méthodes d’élimination appropriées.

Exemples de marquage

pour les batteries

Marquage pour les

équipements

ATTENTION

POUR ÉVITER TOUT RISQUE D’ÉLECTROCUTION, NE

PAS ENLEVER LE COUVERCLE (NI LE PANNEAU

ARRIÈRE). AUCUNE PIÈCE RÉPARABLE PAR

L’UTILISATEUR NE SE TROUVE À L’INTÉRIEUR.

CONFIER TOUT ENTRETIEN À UN PERSONNEL

QUALIFIÉ UNIQUEMENT.

D3-4-2-1-1_B1_Fr

A70_SYXE8-FR.book 2 ページ２０１５年７月２８日　火曜日　午後４時１８分

3

ATTENTION

L’interrupteur /I STANDBY/ON de cet appareil ne

coupe pas complètement celui-ci de sa prise secteur.

Comme le cordon d’alimentation fait office de

dispositif de déconnexion du secteur, il devra être

débranché au niveau de la prise secteur pour que

l’appareil soit complètement hors tension. Par

conséquent, veillez à installer l’appareil de telle

manière que son cordon d’alimentation puisse être

facilement débranché de la prise secteur en cas

d’accident. Pour éviter tout risque d’incendie, le

cordon d’alimentation sera débranché au niveau de

la prise secteur si vous prévoyez une période

prolongée de non utilisation (par exemple avant un

départ en vacances).

D3-4-2-2-2a*_A1_Fr

Milieu de fonctionnement

Température et humidité du milieu de fonctionnement :

De +5 °C à +35 °C (de +41 °F à +95 °F) ; Humidité

relative inférieure à 85 % (orifices de ventilation non

obstrués)

N’installez pas l’appareil dans un endroit mal ventilé ou

un lieu soumis à une forte humidité ou en plein soleil

(ou à une forte lumière artificielle).

D3-4-2-1-7c*_A1_Fr

Ce produit est destiné à une utilisation domestique

générale. Toute panne due à une utilisation autre qu'à

des fins privées (comme une utilisation à des fins

commerciales dans un restaurant, dans un autocar

ou sur un bateau) et qui nécessite une réparation

sera aux frais du client, même pendant la période de

garantie.

K041_A1_Fr

NOTE IMPORTANTE SUR LE CABLE D’ALIMENTATION

Tenir le câble d’alimentation par la fiche. Ne pas

débrancher la prise en tirant sur le câble et ne pas

toucher le câble avec les mains mouillées. Cela risque de

provoquer un court-circuit ou un choc électrique. Ne pas

poser l’appareil ou un meuble sur le câble. Ne pas pincer

le câble. Ne pas faire de noeud avec le câble ou l’attacher

à d’autres câbles. Les câbles d’alimentation doivent être

posés de façon à ne pas être écrasés. Un câble abîmé

peut provoquer un risque d’incendie ou un choc

électrique. Vérifier le câble d’alimentation de temps en

temps. Contacter le service après-vente PIONEER le plus

proche ou le revendeur pour un remplacement.

S002*_A1_Fr

Nous vous remercions pour cet

achat d’un produit Pioneer.

Nous vous demandons de lire soigneusement ce mode

d’emploi ; vous serez ainsi à même de faire fonctionner

l’appareil correctement. Après avoir bien lu le mode

d’emploi, le ranger dans un endroit sûr pour pouvoir s’y

référer ultérieurement.

Table des

matières

01 Préparatifs

Contenu de la boîte . . . . . . . . . . . . . . . . . . . . . . . .4

Chargement des piles dans la télécommande . . . . 4

Utilisation de la télécommande . . . . . . . . . . . . . . . .4

Installation de l’amplificateur . . . . . . . . . . . . . . . .4

02 Raccordement

Raccordements des câbles . . . . . . . . . . . . . . . . . .5

A propos de “bi-câblage (bi-wiring)”. . . . . . . . . . . .5

Connexion des câbles d’enceinte. . . . . . . . . . . . . .6

Raccordement des câbles audio . . . . . . . . . . . . . .6

Raccordement aux bornes d’entrée symétriques

(A-70DA uniquement) . . . . . . . . . . . . . . . . . . . . . .6

Connexions d’entrée audio numérique . . . . . . . . .7

Utilisation d’un câble USB pour brancher un

ordinateur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Utilisation de la commande centralisée avec

d’autres composants Pioneer . . . . . . . . . . . . . . . .7

Branchement. . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

03 Commandes et afficheur

Panneau avant. . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Panneau arrière. . . . . . . . . . . . . . . . . . . . . . . . . . .9

Télécommande . . . . . . . . . . . . . . . . . . . . . . . . . . 10

04 Fonctionnement

Lecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Réglage de la puissance sur la mise en veille . . . .11

Lorsque vous utilisez l’appareil

comme amplificateur de puissance. . . . . . . . . . . .11

Lecture de musique depuis un composant audio

numérique. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Réalisation d’un enregistrement audio . . . . . . . .12

Pour régler un statut de veille automatique

(fonction de mise hors tension automatique). . . .12

Pour restaurer tous les réglages

sur les valeurs par défaut. . . . . . . . . . . . . . . . . . .12

05 Utilisation de la fonction USB DAC

Installation du pilote . . . . . . . . . . . . . . . . . . . . . .13

Lecture de musique depuis ordinateur . . . . . . . .13

06 Informations supplémentaires

Guide de dépannage . . . . . . . . . . . . . . . . . . . . . .14

À propos de la fonction DAC USB . . . . . . . . . . . . .15

Nettoyage de l’unité. . . . . . . . . . . . . . . . . . . . . . .15

Spécifications . . . . . . . . . . . . . . . . . . . . . . . . . . .16

A70_SYXE8-FR.book 3 ページ２０１５年７月２８日　火曜日　午後４時１８分

01 Préparatifs

4

Fr

Chapitre 1 :

Préparatifs

Contenu de la boîte

Veuillez confirmer que les accessoires suivants sont

présents dans la boîte quand vous l’ouvrez.

•Télécommande

• Piles sèches AAA/IEC R03 x 2

• Fiches à broche courte x 2

(Lors de l’achat, ces fiches sont déjà installées sur

les bornes PHONO IN du panneau arrière.)

• Cordon d’alimentation (Longueur : 1,8 m)

• Carte de garantie

• Feuille d’avertissements (pour la première

utilisation)

• Mode d’emploi (ce document)

AVERTISSEMENT

• Gardez les pièces de petite taille hors de la portée

des bébés et des enfants. En cas d’ingestion

accidentelle, veuillez contacter immédiatement un

médecin.

Remarque

• Les illustrations des instructions opérationnelles

peuvent avoir été modifiées ou simplifiées dans le

but de clarification et en conséquence peuvent

différer de l’apparence actuelle du produit.

• Les illustrations utilisées ici représentent

principalement l’A-70DA.

Chargement des piles dans la

télécommande

1 Ouvrez le couvercle arrière.

2 Placez les piles neuves, en faisant

correspondre la polarité à celle du boîtier.

3 Fermez le couvercle arrière.

Les piles incluses avec l’unité ont été fournies pour

permettre de contrôler le fonctionnement du produit et

ne dureront pas longtemps. Nous recommandons

d’utiliser des piles alcalines qui ont une durée de vie

utile plus longue.

AVERTISSEMENT

• N’utilisez ni ne conservez les piles sous la lumière

directe du soleil ou dans un endroit excessivement

chaud, comme une voiture ou à proximité d’un

appareil de chauffage. Les piles risqueraient de

fuir, de surchauffer, d’exploser ou de s’enflammer.

Leur durée de vie ou leur performance pourrait

également être réduite.

Attention

Toute utilisation incorrecte des piles peut entraîner des

accidents, par exemple une fuite ou une explosion.

Respectez les précautions suivantes :

• Lorsque vous placez les piles, prenez soin de ne pas

endommager les ressorts des bornes des piles .

Ceci peut entraîner la fuite ou la surchauffe des

piles.

• Ne pas utiliser de piles autres que celles qui sont

indiquées. Ne pas utiliser non plus une pile neuve

avec une pile usée.

• Lorsque vous installez les piles dans la

télécommande, orientez-les batteries dans la

bonne direction en respectant la polarité ( et ).

• Ne pas chauffer, ni démonter, ni ne jeter les piles

dans le feu ou l’eau.

• La tension des piles peut différer l’une de l’autre et

cela même si leur type et forme sont identiques.

Utiliser ensemble uniquement des piles du même

type.

• Pour éviter que les piles ne fuient, enlever les piles

lorsque le produit n’est pas censé être utilisé

pendant une période prolongée (à savoir 1 mois ou

plus). Si les piles ont fuit, nettoyer soigneusement

1

2

3

l’intérieur du compartiment et placer ensuite les

piles. Si une pile fuit et que du liquide entre en

contact avec votre peau, nettoyer à grande quantité

d’eau.

• Lorsque vous jetez des piles usées, veuillez vous

conformer aux normes gouvernementales ou à la

réglementation des institutions publiques

environnementales en vigueur dans votre pays ou

région.

Utilisation de la télécommande

La télécommande a une portée d’environ 7 mètres avec

un angle de 30° par rapport au capteur de

télécommande.

Gardez à l’esprit ce qui suit lorsque vous utilisez la

télécommande :

• Assurez-vous de l’absence d’obstacles entre la

télécommande et le capteur de l’appareil.

• La télécommande risque de ne pas fonctionner

correctement si la lumière du soleil ou une lampe

fluorescente puissante éclaire le capteur de

l’appareil.

• Les télécommandes de différents appareils

peuvent interférer entre elles. Evitez d’utiliser des

télécommandes commandant d’autres

équipements situés à proximité de cet appareil.

• Remplacez les piles lorsque vous constatez une

diminution de la portée de fonctionnement de la

télécommande.

Installation de l’amplificateur

Lors de l’installation de l’appareil, assurez-vous que ce

dernier est posé sur une surface plane et stable.

•

N’installez pas l’appareil dans les endroits suivants :

– sur un téléviseur couleur (les images à l’écran

pourraient être déformées)

– à proximité d’une platine à cassettes (ou d’un

appareil qui produit un champ magnétique). Le son

pourrait s’en trouver affecté.

– à la lumière directe du soleil

– à l’humidité

– à des températures extrêmes

– en présence de vibrations ou autres mouvements

– à la poussière

– à la fumée ou aux émanations graisseuses

(cuisine par ex.)

• Ne pas installer l’unité sur un divan ou tout autre

objet/matériau ayant des caractéristiques

absorbantes sous risque d’affecter la qualité du

son.

7 m

30 °

A70_SYXE8-FR.book 4 ページ２０１５年７月２８日　火曜日　午後４時１８分

Страница загружается...

Pioneer A-70DA-S Руководство пользователя

Похожие модели бренда

Модели других брендов