HOTPOINT/ARISTON WMSD 723B EU Руководство пользователя

Категория
Стиральные машины
Тип
Руководство пользователя
GB
1
English,1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine, 4-5
Control panel
Display
Running a wash cycle, 6
Wash cycles and functions, 7
Table of wash cycles
Wash functions
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Precautions and tips, 9
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
GB
WMSD 723
Instructions for use
WASHING MACHINE
Polski,13
PL
UA
Українська,25
2
GB
Levelling the machine correctly will provide it with stability,
help to avoid vibrations and excessive noise and prevent it
from shifting while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow a sufficient
ventilation space underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply pipe
by screwing it to a cold
water tap using a ¾ gas
threaded connection (see
figure).
Before performing the con-
nection, allow the water to
run freely until it is perfectly
clear.
2. Connect the inlet hose
to the washing machine by
screwing it onto the corre-
sponding water inlet of the
appliance, which is situa-
ted on the top right-hand
side of the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over or bent.
! The water pressure at the tap must fall within the values
indicated in the Technical details table (see page 3).
! If the inlet hose is not long enough, contact a specialised
shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
! This instruction manual should be kept in a safe place for
future reference. If the washing machine is sold, transferred
or moved, make sure that the instruction manual remains
with the machine so that the new owner is able to familiari-
se himself/herself with its operation and features.
! Read these instructions carefully: they contain vital infor-
mation relating to the safe installation and operation of the
appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been
damaged during the transportation process. If it has been
damaged, contact the retailer and do not proceed any
further with the installation process.
3. Remove the 4 protective
screws (used during tran-
sportation) and the rubber
washer with the correspon-
ding spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them
again if the washing machine needs to be moved to ano-
ther location.
! Packaging materials should not be used as toys for
children.
Levelling
1. Install the washing machine on a flat sturdy floor, without
resting it up against walls, furniture cabinets or anything
else.
2. If the floor is not perfectly
level, compensate for any
unevenness by tightening
or loosening the adjusta-
ble front feet (see figure);
the angle of inclination,
measured in relation to the
worktop, must not exceed
2°.
GB
3
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a drai-
nage duct or a wall drain
located at a height between
65 and 100 cm from the
floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not be
underwater.
! We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150 cm
in length.
Electrical connections
Before plugging the appliance into the electricity socket,
make sure that:
• thesocketisearthedandcomplieswithallapplicable
laws;
• thesocketisabletowithstandthemaximumpowerload
of the appliance as indicated on the Technical Data Plate
fixed on the machine;
• thepowersupplyvoltagefallswithinthevaluesindicated
on the Technical Data Plate fixed on the machine;
• thesocketiscompatiblewiththeplugofthewashing
machine. If this is not the case, replace the socket or the
plug.
! The washing machine must not be installed outdoors,
even in covered areas. It is extremely dangerous to leave
the appliance exposed to rain, storms and other weather
conditions.
! When the washing machine has been installed, the elec-
tricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced by autho-
rised technicians.
Warning! The company shall not be held responsible in the
event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before you use
it for the first time, run a wash cycle with detergent and no
laundry, using the wash cycle (60°C).
Technical data
Model
WMSD 723
Dimensions
width 59.5 cm
height 85 cm
depth 43,5 cm
Capacity
from 1 to 7 kg
Electrical
connections
please refer to the technical data plate
fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 48 litres
Spin speed
up to 1200 rotations per minute
Test wash cycles
in accordance
with directives
1061/2010 and
1015/2010
programme
;
temperature 60°C (2nd press of the button);
temperature 40°C (3rd press of the button).
This appliance conforms to the following
EC Directives:
- 2004/108/EC (Electromagnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2002/96/EC
4
GB
Detergent dispenser drawer: used to dispense deter-
gents and washing additives (see “Detergents and laundry”).
ON/OFF button : press this briefly to switch the ma-
chine on or off. The START/PAUSE indicator light, which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off. If the machine is switched off
during a wash cycle, this wash cycle will be cancelled.
WASH CYCLE SELECTOR buttons: used to set the
desired wash cycle (see “Table of wash cycles”).
MY CYCLE button: press and hold the button to store a
cycle with your own set of preferences in the memory of
the machine. To recall a previously stored cycle, press the
MY CYCLE button.
FUNCTION buttons: press the button to select the
desired function. The corresponding indicator light on the
display will switch on.
CLEANING ACTION
button : to select the desired
wash intensity.
ANTI ALLERGY RINSE
button : press to select
the desired rinse type.
SPIN button : press to reduce or completely exclude
the spin cycle - the value is indicated on the display.
TEMPERATURE button : press to decrease the tem-
perature: the value will be shown on the display.
CHILD LOCK button : to activate the control panel
lock, press and hold the button for approximately 2
seconds. When the symbol is illuminated, the control
panel is locked. This means it is possible to prevent wash
cycles from being modified accidentally, especially where
there are children in the home. To deactivate the control
panel lock, press and hold the button for approximately 2
seconds.
DELAY TIMER button : press to set a delayed start
time for the selected wash cycle. The delay time will be
shown on the display.
START/PAUSE button with indicator light: when the gre-
en indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has started the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
orange colour. If the symbol is not illuminated, the door
may be opened. To start the wash cycle from the point at
which it was interrupted, press the button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Consumption in off-mode: 1 W
Consumption in Left-on: 1 W
Description of the washing machine
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
buttons
Detergent dispenser drawer
FUNCTION
buttons
ON/OFF
button
SPIN SPEED
button
START/PAUSE
button with
indicator light
CHILD LOCK
button
DISPLAY
DELAY
TIMER
button
MY
CYCLE
button
CLEANING
ACTION
button
ANTI
ALLERGY
RINSE
button
GB
5
Display
The display is useful when programming the machine and provides a great deal of information.
The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all informa-
tion relating to the progress status of the wash cycle.
String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been set, the
time remaining until the start of the selected wash cycle.
String D shows the maximum spin speed value (this depends on the selected wash cycle); if the wash cycle does not include
a spin cycle, the string remains unused.
String E shows the maximum temperature value which may be selected (this depends on the wash cycle used); if the tempe-
rature of the wash cycle cannot be modified, the string remains unused.
Indicator lights F correspond to the functions and light up when the selected function is compatible with the set wash cycle.
Door locked symbol
If the symbol is lit, this indicates that the washing machine door is blocked to prevent it from being opened accidentally. To
prevent any damage from occurring, wait for the symbol to switch itself off before opening the appliance door.
N.B.: if the DELAYE TIMER function has been activated, the door cannot be opened; pauses the machine by pressing the
START/PAUSE button if you wish to open it.
! The first time the machine is switched on, you will be asked to select the language and the display will automatically show
the language selection menu.
To select the desired language press the X and Y buttons; to confirm the selection press the Z button.
To change the language switch off the machine and press buttons X, Y, Z simultaneously until an alarm is heard: the
language-selection menu will be displayed again.
A
B
C
D
E
F
Z
X
Y
6
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the On/Off
button ; the text POWER ON will appear on the
display and the START/PAUSE indicator light will flash
slowly in a green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes on the following page.
3. MEASURE OUT THE DETERGENT. Open the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Press one of the WASH
CYCLE SELECTOR buttons to select the required wash
cycle; the name of the wash cycle will appear on the
display. A temperature and spin speed is set for each
wash cycle; these may be adjusted. The duration of the
cycle will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modifying the temperature and/or spin
speed. The machine automatically selects the
maximum temperature and spin speed set for the
selected wash cycle; these values cannot therefore
be increased. The temperature can be decreased by
pressing the button, until the cold wash “OFF”
setting is reached. The spin speed may be progressively
reduced by pressing the button, until it is completely
excluded (the “OFF” setting). If these buttons are
pressed again, the maximum values are restored.
! Exception: if the
(2nd press of the button)
programme
is selected, the temperature can be increased up to a
value of 90°C.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option is enabled, the symbol lights up on the
display. To remove the delayed start function press the
button until the text “OFF” appears on the display.
Set the desired wash intensity.
Option makes it possible to optimise washing
based on the level of soil in the fabrics and on desired
wash cycle intensity.
Select the wash programme: the cycle will be
automatically set toNormalas optimised for garments
with an average level of soil (this setting is not applicable to
the “Wool” cycle, which is automatically set to “Delicate”).
For heavily-soiled garments press button until
the “Super Wash” level is reached. This level ensures
a high-performance wash due to a larger quantity of
water used in the initial phase of the cycle and due to
increased drum rotation. It is useful when removing the
most stubborn stains.
It can be used with or without bleach. If you wish to
bleach the items insert the additional compartment
(4) into compartment 1. When pouring the bleach, be
careful not to exceed the “max” level marked on the
central pivot (see figure pag. 8).
For lightly-soiled garments or a more delicate treatment
of the fabrics, press button until the “Delicate” level
is reached.
The cycle will reduce the drum rotation to ensure
washing results are perfect for delicate garments. If the
current selection can be neither set nor changed, the
display will show “Not allowed”.
Set the rinse type.
Option makes it possible to select the desired rinse
type for sensitive skin. Press the button once for the
Extra Rinse level, which makes it possible to select
an additional rinse after the standard cycle rinse and
remove all traces of detergent. Press the button again
for theSensitive Skinlevel, which makes it possible to
select two additional rinses to the standard cycle rinses; it
is recommended for very sensitive skin. Press the button
for the third time for the “Anti allergy Rinselevel, which
makes it possible to select three additional rinses to the
standard cycle rinses and remove major allergens such as
pollen, mites, cat and dog hair. Press the button again to
go back to theNormal Rinserinse type. If the current
adjustment can be neither set nor changed, the display will
showNot allowed”.
Modifying the cycle settings.
• Pressthebuttontoenablethefunction;theindicator
light corresponding to the button will switch on.
• Pressthebuttonagaintodisablethefunction;the
indicator light will switch off.
! If the selected function is not compatible with the
programmed wash cycle, the indicator light will flash
and the function will not be activated.
! If the selected function is not compatible with
another function which has been selected previously,
the indicator light corresponding to the first function
selected will flash and only the second function will
be activated; the indicator light corresponding to the
enabled function will remain lit.
! The functions may affect the recommended load value
and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/PAUSE
button. The corresponding indicator light will become
green, remaining lit in a fixed manner, and the door will be
locked (the DOOR LOCKED symbol will be on). During
the wash cycle, the name of the phase in progress will
appear on the display. To change a wash cycle while
it is in progress, pause the washing machine using the
START/PAUSE button (the START/PAUSE indicator light
will flash slowly in an orange colour); then select the
desired cycle and press the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash cycle
from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END OF CYCLE” on the display;
when the DOOR LOCKED symbol switches off
the door may be opened. Open the door, unload the
laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
GB
7
Wash cycles and functions
Table of wash cycles
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can
vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any
wash options selected.
For all Test Institutes:
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 60°C (2nd press of the button); set wash cycle 40°C (3rd press of the button).
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be
washed at 60°C and 40°C. The actual washing temperature may differ from the indicated value.
2) Long wash cycle for cottons: set wash cycle 40°C (3rd press of the button).
3) Short wash cycle for cottons: set wash cycle
;
temperature of 40°C (press TEMPERATURE button).
4) Long wash cycle for synthetics: set wash cycle 6C (1st press of the button); temperature of 40°C (press TEMPERATURE button).
Wash functions
Timer Saver
If you select this option, the wash cycle duration will be redu-
ced by up to 50%, depending on the selected cycle, thereby
guaranteeing simultaneous water and energy saving. Use this
cycle for lightly soiled garments.
! It cannot be used with the , “Fastwash 60’”, , , .
Easy Iron
By selecting this function, the wash and spin cycles will be
modified in order to reduce the formation of creases.
At the end of the cycle the washing machine will perform
slow rotations of the drum; the “Easy Iron” and START/
PAUSE indicator lights will flash (orange) and the text “END
OF CYCLE” will appear on the display. To end the cycle,
press the START/PAUSE button or the “Easy Iron” button.
! It cannot be used with the , “Fastwash 30’”, , ,
“Fast spin Cottons” and “Pump out”.
Eco Wash
The Eco Wash function saves energy by not heating the
water used to wash your laundry – an advantage both to
the environment and to your energy bill. Instead, intensified
wash action and water optimisation ensure great wash
results in the same average time of a standard cycle.
For the best washing results we recommend the usage of
a liquid detergent.
! It cannot be used with the , (90°C), , , , .
Wash cycles
Description of the wash cycle
Max.
temp. (°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Residual dam-
pness %
Energy con-
sumption kWh
Total water lt
Cycle duration
PreWash
Wash
Bleach
Fabric
softener
Anti Stain
40° 1200 -
-
4
- - -
180’
Cotton Prewash (1st press of the button): extremely soiled whites
and resistant colours.
90° 1200
-
7 53 2,47 97 185’
White Cottons (1) (2nd press of the button): heavily soiled whites
and delicate colours.
60°
(Max. 90°)
1200 -
7 53 0,99 64 190’
Cottons Coloured (1-2) (3rd press of the button): lightly soiled whites
and delicate colours.
40° 1200 -
7 53 0,94 72 175’
Synthetics Resistant (1st press of the button): heavily soiled resi-
stant colours.
60° 800 -
3 49 0,87 42 90’
Synthetics Resistant (4) (1st press of the button): heavily soiled
resistant colours.
40° 800 -
3 49 0,56 42 80’
Synthetics Delicate (2nd press of the button): lightly soiled resistant
colours.
40° 800 -
3 - - - 75’
Fastwash 60' (1st press of the button): to refresh normal soiled
garments quickly (not suitable for wool, silk and clothes which
require washing by hand).
60° 1200 -
-
3.5 53 0,81 36 60’
Fastwash 30' (2nd press of the button): to refresh lightly soiled
garments quickly (not suitable for wool, silk and clothes which
require washing by hand).
30° 800 -
-
3 71 0,19 39 30’
M
My Cycle: allows for any wash cycle to be stored.
Bed & Bath (3): washes bathroom laundry and bedlinen. 60° 1200 -
-
7 - - - 135’
Woolmark Platinum (Wool): for wool, cashmere, etc. 40° 800 -
-
1.5 - - - 80’
Delicates
30° 0 -
-
1 - - - 75’
Fast Spin Cottons (1st press of the button) - 1200 - - - - 7 - - - 16’
Rinse (2nd press of the button) - 1200 - - -
7 - - - 49’
Pump out (3rd press of the button) - 0 - - - - 7 - - - 2’
8
GB
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessarily
result in a more efficient wash, and may in fact cause a
build up on the inside of your appliance and contribute to
environmental pollution.
! Use powder detergent for white cotton garments, for
pre-washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! Do not use hand washing detergents because these
create too much foam.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra com-
partment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage.
If powder detergent is used, place the partition into slot B.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Preparing the laundry
•Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
•Emptyallgarmentpocketsandcheckthebuttons.
•Donotexceedthelistedvalues,whichrefertotheweight
of the laundry when dry:
Durable fabrics: max. 7 kg
Synthetic fabrics: max. 3 kg
Delicate fabrics: max. 2 kg
Wool: max. 1,5 kg
Silk: max. 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Special wash cycles
Anti Stain : this programme is suitable to heavily-soiled
garments with resistant colours. It ensures a washing
class that is higher than the standard class (A class). When
running the programme, do not mix garments of different
colours. We recommend the use of powder detergent.
Pre-treatment with special additives is recommended if
there are obstinate stains.
Bed & Bath: use programme to wash bed linen and
towels in one single cycle: it optimises softener performan-
ce and helps you save time and energy. We recommend
the use of powder detergent.
Wool: the wool wash cycle on this Hotpoint-Ariston ma-
chine has been tested and approved by The Woolmark
Company for washing wool garments labelled as hand
washable provided that the garments are washed accor-
ding to the instructions on the garment label and those
issued by the manufacturer of this washing machine.
Hotpoint-Ariston is the first washing machine brand to be
approved by The Woolmark Company for Apparel Care-
Platinum for its washing performance and consumption
of energy and water.
Ultradelicates: use programme to wash very delicate
garments having strasses or sequins.
To wash silk garments and curtains select the cycle
and set the “Delicate” level from option .
We recommend turning the garments inside out before
washing and placing small items into the special bag
for washing delicates. Use liquid detergent on delicate
garments for best results.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
M
AX
1
2
4
3
A
B
Detergents and laundry
GB
9
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
Thisapplianceisnotintendedforusebypersons(inclu-
ding children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concer-
ning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that
they do not play with the appliance.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
• Donottouchthedrainedwaterasitmayreachextreme-
ly high temperatures.
Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
• Iftheappliancebreaksdown,donotunderanycircum-
stances access the internal mechanisms in an attempt
to repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocalregu-
lations so that the packaging may be re-used.
•TheEuropeanDirective2002/96/EConWasteElectrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must be
collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce the im-
pact on human health and the environment. The crossed
out “wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the appliance it
must be separately collected. Consumers should contact
their local authority or retailer for information concerning the
correct disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if it
is not, remove excess water
using the drain hose, collec-
ting it in a bucket as indicated
in the figure.
3. using a screwdriver, remo-
ve the cover panel on the lo-
wer front part of the washing
machine (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
10
GB
Care and maintenance
Cutting off the water and electricity
supplies
• Turnoffthewatertapaftereverywashcycle.Thiswilllimit
wear on the hydraulic system inside the washing machine
and help to prevent leaks.
• Unplugthewashingmachinewhencleaningitanddu-
ring all maintenance work.
Cleaning the washing machine
•Theouterpartsandrubbercomponentsoftheapplian-
ce can be cleaned using a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
•Thewashingmachinehasa“AutoClean”programme
for its internal parts that must be run with no load in the
drum.
For maximum performance you may want to use either
the detergent (i.e. a quantity 10% the quantity specified
for lightly-soiled garments) or special additives to clean
the washing machine. We recommend running a cleaning
programme every 40 wash cycles.
To start the programme press buttons A and B simulta-
neously for 5 seconds (see figure).
The programme will start automatically and will last appro-
ximately 70 minutes. To stop the cycle press the START/
PAUSE button.
Cleaning the detergent dispenser drawer
Remove the dispenser by
raising it and pulling it out
(see figure).
Wash it under running wa-
ter; this operation should be
repeated frequently.
Caring for the door and drum of your
appliance
• Alwaysleavetheportholedoorajarinordertoprevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes, small
items (such as coins or buttons) may fall into the pre-cham-
ber which protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and unplug the
appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washing machine (see
figure);
2. unscrew the lid by rota-
ting it anti-clockwise (see
figure): a little water may
trickle out. This is perfectly
normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are any
cracks, it should be replaced immediately: during the wash
cycles, water pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
1
2
A
B
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the text “NO WATER,
CHECK SUPPLY” appears on the
display).
The washing machine continuously
takes in and
drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The machine is locked and the display
flashes, indicating an
error code (e.g. F-01, F-..).
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset(see “Running a wash cycle”).
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
• Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain
phase to be started manually (see “Wash cycles and functions”).
• TheEASYIRONfunctionhasbeenactivated:Tocompletethewashcycle,
press the START/PAUSE button (see “Wash cycles and functions”).
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
• Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext
“for washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Before calling for Assistance:
• Check whether you can solve the problem alone (see “Troubleshooting”);
• Restarttheprogrammetocheckwhethertheproblemhasbeensolved;
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
Service
13
PL
Polski
Spis treści
Instalacja, 14-15
Rozpakowanie i wypoziomowanie
Podłączenia hydrauliczne i elektryczne
Pierwszy cykl prania
Dane techniczne
Opis pralki, 16-17
Panel sterowania
Wyświetlacz
W jaki spob wykonać cykl prania, 18
Programy i funkcje, 19
Tabela programów
Funkcje prania
Środki piorące i bielizna, 20
Szuadka na środki piorące
Przygotowanie bielizny
Programy specjalne
System równoważenia ładunku
Zalecenia i środki ostrożności, 21
Ogólne zasady bezpieczeństwa
Utylizacja
Ręczne otwieranie okrągłych drzwiczek
Utrzymanie i konserwacja, 22
Odłączenie wody i prądu elektrycznego
Czyszczenie pralki
Czyszczenie szuadki na środki piorące
Konserwacja okrągłych drzwiczek i bębna
Czyszczenie pompy
Kontrola przewodu doprowadzającego wodę
Nieprawidłowości w działaniu i sposoby
ich usuwania, 23
Serwis Techniczny, 24
PL
WMSD 723
Instrukcja obsługi
PRALKA
14
PL
Instalacja
! Należy zachować niniejszą książeczkę, aby móc z niej
skorzystać w każdej chwili. W przypadku sprzedaży,
odstąpienia lub przeniesienia pralki w inne miejsce
należy zadbać o przekazanie instrukcji wraz z maszyną,
aby nowy właściciel mógł zapoznać się z działaniem
urządzenia i z dotyczącymi go ostrzeżeniami.
! Należy uważnie przeczytać instrukcję obsługi: za-
wiera ona ważne informacje dotyczące instalacji oraz
właściwego i bezpiecznego użytkowania pralki.
Rozpakowanie i wypoziomowanie
Rozpakowanie
1. Rozpakować pralkę.
2. Sprawdzić, czy nie doznała ona uszkodzeń w czasie
transportu. W przypadku stwierdzenia uszkodzeń nie
podłączać jej i skontaktować się ze sprzedawcą.
3. Odkręcić 4 śruby
zabezpieczające maszynę
na czas transportu oraz
zdjąć gumowy element z
podkładką, znajdujący się
w tylnej części pralki (patrz
rysunek).
4. Zatkać otwory przy pomocy plastikowych zaślepek,
znajdujących się w wyposażeniu maszyny.
5. Zachować wszystkie części: w razie konieczności
przewiezienia pralki w inne miejsce, powinny one zostać
ponownie zamontowane.
! Części opakowania nie są zabawkami dla dzieci.
Poziomowanie
1. Ustawić pralkę na płaskiej i twardej podłodze, nie
opierając jej o ściany, meble itp.
2. Jeśli podłoga nie
jest idealnie pozioma,
należy skompensować
nierówności, odkręcając
lub dokręcając przednie
nóżki (patrz rysunek); kąt
nachylenia, zmierzony na
górnym blacie pralki nie
powinien przekraczać 2°.
Staranne wypoziomowanie pralki zapewnia jej stabilność
i zapobiega wibracjom, hałasowi oraz przesuwaniu się
maszyny w czasie pracy. W razie ustawienia na dywa-
nie lub wykładzinie dywanowej należy tak wyregulować
nóżki, aby pod pralką pozostawała wolna przestrzeń
niezbędna dla wentylacji.
Podłączenia hydrauliczne i elektryczne
Podłączenie przewodu doprowadzającego wodę
1. Podłączyć przewód
zasilający poprzez
przykręcenie do zaworu
wody zimnej z końcówką
gwintowaną ¾ gas (patrz
rysunek).
Przed podłączeniem
spuszczać wodę do mo-
mentu, aż stanie się ona
całkowicie przezroczysta.
2. Podłączyć do maszyny
przewód doprowadzający
wodę, przykręcając go
do odpowiedniego ot-
woru dopływowego,
znajdującego się w tylnej
części pralki, z prawej
strony u góry
(patrz rysunek).
3. Zwrócić uwagę, aby na przewodzie nie było zagięć ani
zwężeń.
! Ciśnienie wody w kurku powinno mieścić się w prze-
dziale podanym w tabeli Danych technicznych (patrz
strona obok).
! Jeśli długość przewodu doprowadzającego wodę jest
niewystarczająca, należy zwrócić się do specjalistyczne-
go sklepu lub do autoryzowanego technika.
! Nigdy nie instalować już używanych przewodów.
! Stosować przewody znajdujące się w wyposażeniu
maszyny.
15
PL
65 - 100 cm
Podłączenie przewodu odpływowego
Podłączyć przewód
odpływowy, nie zginając
go, do rury ściekowej lub
do otworu odpływowego
w ścianie, które powin-
ny znajdować się na
wysokości od 65 do 100
cm od podłogi;
ewentualnie oprzeć go na
brzegu zlewu lub wanny,
przymocowując do kranu
prowadnik, znajdujący
się w wyposażeniu (patrz
rysunek). Wolny koniec
przewodu odpływowego
nie powinien być zanurzo-
ny w wodzie.
! Odradza się stosowanie przewodów przedłużających;
jeśli to konieczne, przewód przedłużający powinien mieć
taką samą średnicę jak oryginalny, a jego długość nie
może przekraczać 150 cm.
Podłączenie elektryczne
Przed włożeniem wtyczki do gniazdka elektrycznego
należy się upewnić, czy:
• gniazdko posiada uziemienie i jest zgodne z
obowiązującymi przepisami;
• gniazdko jest w stanie wytrzymać maksymalne
obciążenie mocy maszyny, wskazane w tabeli Danych
technicznych (patrz obok);
• napięcie zasilania mieści się w wartościach wskazany-
ch w tabeli Danych technicznych
(patrz obok);
• gniazdko pasuje do wtyczki pralki. W przeciwnym razie
należy wymienić gniazdko lub wtyczkę.
! Nie należy instalować pralki na otwartym powietrzu, na-
wet w osłoniętym miejscu, gdyż wystawienie urządzenia
na działanie deszczu i burz jest bardzo niebezpieczne.
! Po zainstalowaniu pralki gniazdko elektryczne powinno
być łatwo dostępne.
! Nie używać przedłużaczy ani rozgałęźników.
! Przewód nie powinien być pozginany ani przygnieciony.
! Przewód zasilania elektrycznego może być wymieniany
wyłącznie przez autoryzowanych techników.
Uwaga! Producent nie ponosi żadnej odpowiedzialności
w przypadku nieprzestrzegania powyższych zasad.
Pierwszy cykl prania
Po zainstalowaniu pralki, przed przystąpieniem do jej
użytkowania, należy wykonać jeden cykl prania ze środkiem
piorącym, ale bez wsadu, nastawiając program (60°C).
Dane techniczne
Model WMSD 723
Wymiary
szerokoϾ cm 59,5
wysokoϾ cm 85
g³êbokoœæ cm 43,5
PojemnoϾ od 1 do 7 kg
Dane pr¹du
elektrycznego
dane techniczne umieszczone s¹ na
tabliczce na maszynie
Dane sieci
wodoci¹gowej
Maksymalne ciœnienie 1 MPa (10 barów)
ciœnienie minimalne 0,05 MPa (0,5 barów)
pojemnoœæ bêbna 48 litrów
SzybkoϾ
wirowania
do 1200 obrotów na minutê
Programy testowe
zgodnie z dyrekty-
wami 1061/2010 i
1015/2010
program
;
temperatura 60°C
(2. naciśnięcie przycisku);
temperatura 40°C (3. naciśnięcie przycisku).
Urz¹dzenie to zosta³o wyprodukowane
zgodnie z nastêpuj¹cymi przepisami EWG:
- 2004/108/CE (o Kompatybilnoœci
Elektromagnetycznej)
- 2006/95/CE (o Niskim Napiêciu)
- 2002/96/CE
16
PL
Szuadka na środki piorące: do dozowania środków
piorących i dodatków (patrz „Środki piorące i bielizna”).
Przycisk ON/OFF : nacisnąć krótko przycisk w celu
włączenia lub wyłączenia maszyny. Kontrolka START/
PAUSE, która pulsuje powoli w kolorze zielonym wskazu-
je, że maszyna jest włączona. W celu wyłączenia pralki
podczas prania konieczne jest dłuższe przytrzymanie
naciśniętego przycisku, przez około 3 sek.; krótkie lub
przypadkowe naciśnięcie wystarczy do wyłączenia ma-
szyny. Wyłączenie maszyny podczas trwającego prania
anuluje program prania.
Przyciski PRZEŁĄCZNIKA PROGRAMÓW: w celu wybra-
nia potrzebnego programu (patrz „Tabela programów”).
Przycisk
MY CYCLE
: przytrzymać naciśnięty przycisk
w celu zapisania w pamięci cyklu oraz własnych prefero-
wanych personalizacji. W celu przywołania cyklu zapisa-
nego uprzednio należy nacisnąć przycisk
MY CYCLE
.
Przyciski FUNKCJI: nacisnąć przycisk w celu wybra-
nia potrzebnej funkcji. Na wyświetlaczu zaświeci się
odpowiednia kontrolka.
Przycisk
OPCJE PRANIA
: nacisnąć w celu wybrania
żądanego stopnia intensywności prania.
Przycisk
TYP PŁUKANIA
: nacisnąć w celu wybra-
nia żądanego rodzaju płukania.
Przycisk WIROWANIA : nacisnąć w celu zmniejszenia
lub całkowitego wyłączenia wirówki – wartość ukazana
zostanie na wyświetlaczu.
Przycisk TEMPERATURY : nacisnąć w celu zmniejsze-
nia temperatury: wartość zostaje wyświetlona na ekranie.
Przycisk BLOKADA PRZYCISKÓW : w celu
uruchomienia lub wylaczenia blokady panelu sterowania
nalezy przytrzymac nacisniety przycisk przez okolo
2 sekundy. Podswietlony symbol wskazuje, ze
panel sterowania zostal zablokowany. W ten sposób
uniemozliwia sie dokonywanie przypadkowych zmian w
programach, zwlaszcza, jesli w domu obecne sa dzieci.
W celu wylaczenia blokady panelu sterowania nalezy
przytrzymac nacisniety przycisk przez okolo 2 sekundy.
Przycisk URUCHOMIENIE OPÓZNIONE : nacisnąc w
celu ustawienia opóźnionego uruchomienia wybranego
programu. Opóźnienie wyświetlone zostanie na ekranie.
Przycisk z kontrolką START/PAUSE: kiedy zielona kon-
trolka pulsuje powoli, nacisnąć przycisk w celu urucho-
mienia prania. Po uruchomieniu cyklu kontrolka świeci w
sposób ciągły. W celu wybrania pauzy w praniu należy
nacisnąć ponownie przycisk, kontrolka zacznie pulsować
w kolorze pomarańczowym. Jeśli symbol nie świeci
się, można otworzyć drzwiczki. W celu ponownego uru-
chomienia prania od miejsca, w którym zostało przerwa-
ne, należy ponownie nacisnąć przycisk.
Funkcja stand by
Pralka ta, w myśl nowych norm europejskich związanych
z oszczędnością elektryczną, posiada system auto
wyłączenia (stand by), który włącza się po 30 minutach
nie użytkowania. Ponownie lekko wcisnąć przycisk
ON/OFF i poczekać, aż pralka ponownie włączy się.
Zużycie w trybie wyłączenia: 1W
Zużycie w trybie czuwania: 1W
Opis pralki
Panel sterowania
Szuadka na środki piorące
Przycisk z
kontrolką
START/PAUSE
Przycisk
TEMPERATURY
Przyciski
PRZEŁĄCZNIKA
PROGRAMÓW
Przyciski
FUNKCJI
Przycisk
ON/OFF
Przycisk
WIROWANIA
Przycisk
BLOKADA
PRZYCISKÓW
Wyświetlacz
Przycisk
URUCHOMIENIE
OPÓŹNIONE
Przycisk
MY CYCLE
Przycisk
OPCJE
PRANIA
Przycisk
TYP
PŁUKANIA
17
PL
Wyświetlacz
Wyświetlacz potrzebny jest w celu programowania maszyny i dostarcza wielu informacji.
W obu wierszach górnych A i B wyświetlane są: wybrany program prania, faza prania bieżącego oraz wszelkie wskaza-
nia związane ze stanem zaawansowania programu.
W wierszu C wyświetlany jest czas pozostały do końca cyklu prania bieżącego oraz, jeśli zaprogramowano URUCHO-
MIENIE OPÓŹNIONE, czas brakujący do uruchomienia wybranego programu.
W wierszu D wyświetlana jest maksymalna wartość szybkości wirówki, jaką maszyna może uzyskać w przypadku wybra-
nego programu; jeśli program nie przewiduje wirowania wiersz pozostaje wygaszony.
W wierszu E wyświetlana jest maksymalna wartość temperatury, jaką można wybrać w przypadku wybranego programu,
jeśli program nie przewiduje ustawiania temperatury, wiersz pozostaje wygaszony.
Kontrolki F związane są z funkcjami i włączają się, kiedy wybrana funkcja zgodna jest z wybranym programem.
Symbol zablokowanych drzwiczek
Zapalony symbol oznacza, że okrągłe drzwiczki pralki są zablokowane, aby zapobiec przypadkowemu ich otworzeniu.
Aby uniknąć uszkodzenia pralki, należy odczekać, aż symbol ten zgaśnie, zanim przystąpi się do otwierania drzwiczek
pralki.
Uwaga: jeśli aktywna jest funkcja URUCHOMIENIE OPÓŹNIONE drzwiczek nie można otworzyć. W celu ich otwarcia
należy ustawić maszynę w pauzie poprzez naciśnięcie przycisku START/PAUSE.
! Podczas pierwszego uruchomienia wymagane będzie dokonanie wyboru języka a wyświetlacz ustawi się automatycznie
na menu wyboru języka.
W celu wybrania żądanego języka nacisnąć przyciski X i Y, dla potwierdzenia wyboru nacisnąć przycisk Z.
Aby zmienić język, należy wyłączyć urządzenie, nacisnąć równocześnie przyciski X, Y, Z, aż do usłyszenia sygnału
dźwiękowego, wyświetli się menu wyboru języka.
A
B
C
D
E
F
Z
X
Y
18
PL
W jaki sposób wykonać cykl prania
1. WŁĄCZENIE MASZYNY. Nacisnąć przycisk , na
wwietlaczu pojawi się napis WŁĄCZENIE, kontrolka
START/PAUSE zacznie powoli pulsować w kolorze zielonym.
2. WKŁADANIE BIELIZNY. Otworzyć szklane drzwiczki.
ożyć bieliz uważac, aby nie przekroczyć wielkości
wsadu wskazanej w tabeli programów na następnej stronie.
3. DOZOWANIE ŚRODKA PIORĄCEGO. Wysunąć
szuadkę i wsypać detergent do odpowiednich komór w
sposób wyjaśniony w „Środki piorące i bielizna”.
4. ZAMKNĄĆ DRZWICZKI.
5. WYBÓR PROGRAMU. Nacisnąć jeden z przycisków
PRZEŁĄCZNIKA PROGRAMÓW w celu wybrania
potrzebnego programu, nazwa programu pojawi się na
wyświetlaczu; z nim powiązana jest temperatura oraz
prędkość wirowania, które mogą zostać zmienione. Na
wyświetlaczu pojawi się czas trwania cyklu.
6. PERSONALIZACJA CYKLU PRANIA.
Przy pomocy odpowiednich przycisków:
Zmienić temperaturę i/lub wirówkę. Maszyna
wybierze automatycznie temperaturę oraz wirówkę
maksymalne przewidziane dla danego programu, dlatego
nie mogą one być zwiększane. Poprzez naciskanie
przycisku stopniowo zmniejsza się temperaturę aż do
prania w zimnej wodzie „OFF”. Naciskając przycisk
stopniowo zmniejsza się wirówkę aż do jej wyłączenia
„OFF”. Dodatkowe naciśnięcie przycisków przywróci
maksymalne wartości przewidywane.
! Wyjątek: wybierając program
(2. nacnięcie przycisku)
temperaturę można podnieść aż do 90°.
Ustawienie oźnionego rozpoczęcia.
W celu ustawienia opóźnionego rozpoczęcia wybranego
programu należy naciskać odpowiedni przycisk do
osiągnięcia żądanego czasu opóźnienia. Kiedy opcja ta jest
aktywna, na wwietlaczu pojawia ssymbol . W celu
usunięcia opóźnionego uruchomienia należy naciskać
przycisk aż do pojawienia się napisu “OFF”.
Ustawić żądany stopień intensywności prania.
Opcja umożliwia optymalizację prania w
zależności od stopnia zabrudzenia tkanin oraz żądanej
intensywności prania.
Wybrać program prania, cykl zostanie automatycznie
ustawiony na poziomie „NORMALNY”, przeznaczonym
dla średnio zabrudzonej odzieży, (ustawienie to
nie stosuje się dla cyklu „Wełna”, który ustawia się
automatycznie na poziomie „DELIKATNE”).
W przypadku silnie zabrudzonej odzieży, należy nacisnąć
przycisk aż do przejścia do poziomu „SUPER
PRANIE”. Poziom ten gwarantuje wysokiej jakości
pranie, dzięki użyciu większej ilości wody w początkowej
fazie cyklu i intensywniejszym ruchom mechanicznym
służy do usuwania najoporniejszych plam. Może być
używany z wybielaczem i bez niego.
Jeśli chce się przeprowadzić wybielanie, należy włożyć
dodatkową szuadkę 4, znajdującą się w wyposażeniu,
do szuadki 1. Nie przekraczać poziomu „max”
wybielacza w płynie, podanej na środkowym wskaźniku
(zobacz rysunek na str. 20).
W przypadku lekko zabrudzonej odzieży lub w celu
delikatnego obchodzenia się z tkaninami, należy
nacisnąć przycisk aż do przejścia do poziomu
DELIKATNE”. Cykl zredukuje ruchy mechaniczne,
aby zagwarantować doskonały efekt prania delikatnej
odzieży. Jeśli któreś z ustawień lub zmiana ustawienia
nie jest możliwe, na wyświetlaczu pojawi się napis
ZABLOKOWANE”.
Ustawić rodzaj płukania.
Opcja umożliwia wybranie rodzaju płukania
przeznaczonego do jak największej ochrony delikatnej
skóry. Po pierwszym naciśnięciu przycisku, zostaje
ustawiony poziom „EXTRA PŁUKANIE”, który pozwala
wybrać dodatkowe płukanie, oprócz standardowego,
w celu usunięcia wszelkich pozostałości detergentu.
Po drugim naciśnięciu przycisku, zostaje ustawiony
poziom „WRAŻLIWA SKÓRA”, który pozwala wybrać
dwa dodatkowe płukania, oprócz standardowego, w
celu jak najlepszej ochrony delikatnej skóry. Po trzecim
naciśnięciu przycisku, zostaje ustawiony poziom
ANTYALERGICZNE”, który pozwala wybrać trzy
dodatkowe płukania, oprócz standardowego, w celu
usunięcia głównych alergenów, takich jak pyłki, roztocza,
sierść psów i kotów. Nacisnąć ponownie przycisk, aby
powrócić do „PŁUKANIE STANDARDOWE” rodzaju
płukania. Jeśli któreś z ustawień lub zmiana ustawienia
nie jest możliwe, na wyświetlaczu pojawi się napis
ZABLOKOWANE”.
Zmiana charakterystyki cyklu.
Naciskać przycisk w celu uruchomienia funkcji;
zaświeci się kontrolka odpowiadająca przyciskowi.
Nacisnąć ponownie przycisk w celu wyłączenia funkcji,
kontrolka zgaśnie.
! Jeśli wybrana funkcja nie jest zgodna z wybranym
programem, kontrolka będzie pulsować, a funkcja nie
zostanie uruchomiona.
! Jeśli wybrana funkcja nie jest zgodna z inną, ustawioną
uprzednio, kontrolka odpowiadająca pierwszej funkcji
będzie pulsowała i uruchomiona zostanie jedynie druga
funkcja a kontrolka uruchomionej funkcji zaświeci się.
! Funkcje mogą zmieniać zalecane obciążenie i/lub czas
trwania cyklu.
7. URUCHOMIENIE PROGRAMU. Nacisnąć przycisk
START/PAUSE. Odpowiednia kontrolka zwieci się
kolorem zielonym i drzwiczki zostazablokowane
(symbol ZABLOKOWANYCH DRZWICZEK świeci
się). Podczas prania na wyświetlaczu pojawi się nazwa
bieżącej fazy. W celu zmiany programu w czasie trwania
cyklu należy ustawić pralkę w pauzie naciskając przycisk
START/PAUSE (kontrolka START/PAUSE zacznie powoli
pulsować w kolorze pomarańczowym); następnie wybrać
potrzebny cykl i ponownie nacisnąć przycisk START/
PAUSE. W celu otwarcia drzwiczek w trakcie wykonywania
cyklu należy nacisnąć przycisk START/PAUSE; jeśli
symbol ZABLOKOWANYCH DRZWICZEK jest
wyłączony możliwe będzie otwarcie drzwiczek Nacisnąć
ponownie przycisk START/PAUSE, aby uruchomić
program od punktu, w którym został przerwany.
8. KONIEC PROGRAMU. Wskazywany jest napisem
„KONIEC CYKLU” na wyświetlaczu, kiedy symbol
ZABLOKOWANYCH DRZWICZEK wyłączy się,
możliwe będzie otwarcie drzwiczek. Otworzyć drzwiczki,
wyjąć bieliznę i wyłączyć maszynę.
! Jeśli zamierza się anulować uruchomiony juz cykl,
przytrzymać dłużej naciśnięty przycisk . Cykl zostanie
przerwany i maszyna wyłączy się.
19
PL
Programy i funkcje
Tabela programów
Funkcje prania
Pranie szybkie
Wybierając opc, skraca s czas trwania programu na-
wet do 50%, w zalności od wybranego cyklu, gwarantując
równocześnie oszcdnć wody i energii. Z cyklu naly
korzystać do prania niezbyt zabrudzonej odziy.
! Nie można jej uruchomić w programach , “Szybkie
Pranie 60’”, , , .
Łatwe prasowanie
Po wybraniu tej funkcji, pranie oraz wirówka zostaną
odpowiednio zmienione w celu ograniczenia
powstawania zgnieceń.
Po zakończeniu cyklu pralka wykona powolne obroty
bębna, kontrolka funkcji ŁATWE PRASOWANIE zaświeci
się, a kontrolka START/PAUSE będzie pulsowała powoli
w kolorze pomarańczowym. W celu zakończenia cyklu
należy nacisnąć przycisk START/PAUSE lub przycisk
ŁATWE PRASOWANIE.
! Nie można go uruchomić w programach ,
“Szybkie Pranie 30’”, , , “Wirowanie Intensywne” i
“Odprowadzamie wody”.
Eco wash
Funkcja Eco Wash umożliwia oszczędności pod
względem zużywanej energii, nie podgrzewając wody
używanej do prania, co niesie za sobą korzyści zarówno
dla środowiska naturalnego, jak i dla rachunku za prąd.
Wzmocniona siła działania i zoptymalizowane zużycie
wody gwarantują doskonałe rezultaty przy długości
cyklu takiej samej, jak w przypadku cyklu standard. Aby
uzyskać jak najlepsze rezultaty, zalecamy korzystać z
płynu do prania.
! Nie można jej uruchomić w programach , (90°C),
, , , .
Dla wszystkich Instytucji homologacyjnych:
(1) Program kontrolny zgodny z normą 2010/1061: ustawić program w 60 °C (2. nacnięcie przycisku); ustawić program na 40 °C (3. nacnięcie przycisku).
Ten cykl jest odpowiedni do prania średnio zabrudzonej odzieży bawnianej i jest najbardziej wydajnym cyklem pod względem łącznego zużycia energii elektrycznej i wody; naly go używać do
odziy przeznaczonej do prania w 60°C i 4C. Rzeczywista temperatura prania może s różnić od podanej.
(2)
Program bawełna, długi:
ustawić program na 40 °C (3. naciśnięcie przycisku).
(3)
Program bawełna, krótki:
ustawić program ; temperatura na 40 °C (nacisnąć przycisk TEMPERATURA).
(4) Program tkaniny syntetyczne długi
:
ustawić program w 60 °C (1. naciśnięcie przycisku); temperatura na 40 °C (nacisnąć przycisk TEMPERATURA).
Czas trwania cyklu wskazany na wyświetlaczu lub w instrukcji jest czasem oszacowanym dla standardowych warunków. Rzeczywisty czas trwania cyklu może się
zmieniać w zależności od wielu czynników, takich jak temperatura i ciśnienie wody na wlocie, temperatura otoczenia, ilość detergentu, ilość i rodzaj pranej odzieży,
wyważenie ładunku, wybrane opcje dodatkowe.
Programy
Opis programu
Temp. max.
(°C)
Prêd-
koϾ
max
(obro-
tów na
minutê)
Œrodki pior¹ce
£adunek max (kg)
Wilgotno�� resztko-
wa %
Zu�ycie energii kWh
Woda ł�cznie lt
Czas trwania cyklu
Pranie
wstępne
Pranie
Wybielacz
Œrodek
zmiêk-
czaj¹cy
ODPLAMIANIE
40° 1200 -
-
4
- - -
180’
PRANIE WSTĘPNE (1° naciœniêcie przycisku): bielizna bia³a silnie
zabrudzona.
90° 1200
-
7 53 2,47 97 185’
BAWEŁNA BIAŁE (1) (2° naciœniêcie przycisku): tkaniny bia³e i koloro-
we, wytrzyma³e, mocno zabrudzone.
60°
(Max. 90°)
1200 -
7 53 0,99 64 190’
BAWEŁNA KOLOROWE (1-2) (3° naciœniêcie przycisku): tkaniny kolo-
rowe, wytrzyma³e, lekko zabrudzone.
40° 1200 -
7 53 0,94 72 175’
SYNTETYCZNE INTENSYWNY (1° naciœniêcie przycisku): tkaniny
kolorowe, wytrzyma³e, mocno zabrudzone.
60° 800 -
3 49 0,87 42 90’
SYNTETYCZNE INTENSYWNY (4) (1° naciœniêcie przycisku): tkaniny
kolorowe, wytrzyma³e, mocno zabrudzone.
40° 800 -
3 49 0,56 42 80’
SYNTETYCZNE DELIKATNE (2° naciœniêcie przycisku): tkaniny kolo-
rowe, wytrzyma³e, lekko zabrudzone.
40° 800 -
3 - - - 75’
SZYBKIE PRANIE 60’ (1° naciœniêcie przycisku): w celu szybkie-
go odœwie¿enia mocno zabrudzonych tkanin (niewskazany dla
we³ny, jedwabiu i tkanin przeznaczonych do prania rêcznego).
60° 1200 -
-
3.5 53 0,81 36 60’
SZYBKIE PRANIE 30(2° naciœniêcie przycisku): w celu szybkiego
odœwie¿enia lekko zabrudzonych tkanin (niewskazany dla we³ny,
jedwabiu i tkanin przeznaczonych do prania rêcznego).
30° 800 -
-
3 71 0,19 39 30’
M
MY CYCLE (PAMIEÆ): pozwala na zmemoryzowanie ka¿dego typu prania.
POŚCIEL I RĘCZNIKI (3): do bielizny poœcielowej i k¹pielowej.
60° 1200 -
-
7 - - - 135’
Woolmark Platinum (WE£NA): do we³ny, kaszmiru, itp.
40° 800 -
-
1.5 - - - 80’
DELIKATNE
30° 0 -
-
1 - - - 75’
WIROWANIE (1° naciœniêcie przycisku).
- 1200 - - - - 7 - - - 16’
PŁUKANIE (2° naciœniêcie przycisku).
- 1200 - - -
7 - - - 49’
ODPROWADZANIE WODY (3° naciœniêcie przycisku).
- 0 - - - - 7 - - - 2’
20
PL
Środki piorące i bielizna
Szuadka na środki piorące
Dobry rezultat prania zależy również od prawidłowego
dozowania środka piorącego: użycie jego nadmiernej
ilości nie poprawia skuteczności prania, lecz przyczynia
się do powstawania nalotów na wewnętrznych częściach
pralki i do zanieczyszczania środowiska.
! Środki piorące w proszku należy stosować do tkanin z
białej bawełny i do prania wstępnego oraz do prania w
temperaturze przekraczającej 60°C.
! Należy stosować się do zaleceń podanych na opako-
waniu środka piorącego.
! Nie stosować środków do prania ręcznego, ponieważ
tworzą one za dużo piany.
Wysunąć szuadkę i
umieścić w niej środek
piorący lub dodatkowy w
następujący sposób.
Przegródka 1: Środek
piorący do prania
wstępnego (w proszku)
Przed wsypaniem
środka piorącego należy
sprawdzić, czy nie jest włożony dodatkowy pojemnik 4.
Przegródka 2: Środek piorący do prania zasadnicze-
go (w proszku lub w płynie)
W przypadku stosowania środka piorącego w płynie, za-
leca się użycie ścianki A dostarczonej na wyposażeniu,
która ułatwia prawidłowe dozowanie. W celu użycia
środka piorącego w proszku, należy wsunąć ściankę w
zgłębienie B.
Przegródka 3: Środki dodatkowe (zmiękczające, itp.)
Środek zmiękczacy nie powinien wyyw poza kratkę.
dodatkowy pojemnik 4: Wybielacz
Przygotowanie bielizny
• Podzielić bieliznę do prania według:
- rodzaju tkaniny / symbolu na etykietce.
- kolorów: oddzielić tkaniny kolorowe od białych.
• Opróżnić kieszenie i sprawdzić guziki.
• Nie przekraczać wskazanego ciężaru suchej bielizny:
Tkaniny wytrzymałe: max 7 kg
Tkaniny syntetyczne: max 3 kg
Tkaniny delikatne: max 2 kg
Wełna: max 1,5 kg
Jedwab: max 1 kg
Ile waży bielizna?
1 prześcieradło 400-500 gr.
1 poszewka 150-200 gr.
1 obrus 400-500 gr.
1 szlafrok 900-1.200 gr.
1 ręcznik 150-250 gr.
M
AX
1
2
4
3
A
B
Programy specjalne
ODPLAMIANIE: program odpowiedni do prania silnie
zabrudzonej odzieży o trwałych kolorach. Program gwa-
rantuje klasę prania wyższą od standardowej (klasa A).
Nie używać programu, gdy miesza się odzież w różnych
kolorach. Zalecamy stosowanie środka piorącego w
proszku. W przypadku szczególnie opornych plam, zale-
camy wcześniej zastosowanie specjalnych dodatków.
POŚCIEL I RĘCZNIKI: w celu wyprania bielizny
kąpielowej i pościelowej w jednym cyklu, należy użyć
programu , który optymalizuje zużycie środka
piorącego i pozwala oszczędzać czas i pieniądze. Zale-
camy stosowanie środka piorącego w proszku.
Wełna: cykl prania „Wełna” niniejszej pralki Hotpoint-Ari-
ston zostprzetestowany i zatwierdzony przez Woolmark
Company jako odpowiedni do prania odzieży wełnianej
przeznaczonej wyłącznie do prania ręcznego, pod warunki-
em, że pranie jest przeprowadzane zgodnie z instrukcjami
podanymi na etykiecie ubrania oraz ze wskazówkami do-
starczonymi przez producenta urządzenia. Hotpoint-Ariston
to pierwsza marka pralek, która uzyskała od Woolmark
Company certykat Woolmark Apparel Care - Platinum ze
względu na osiągane rezultaty prania oraz zużycie wody i
energii.
DELIKATNE: używać programu do prania bardzo
delikatnej odzieży, ozdobionej cekinami lub koralikami.
Do prania jedwabiu i zasłon, należy wybrać cykl i
ustawić poziom „DELIKATNE” opcji .
Zalecamy wywrócenie ubrań na lewą stronę i włożenie
małych części odzieży do woreczka przeznaczonego
specjalnie do prania delikatnych ubrań.
Dla osiągnięcia najlepszych efektów, zalecamy
stosowanie środka piorącego w płynie do tkanin
delikatnych.
System równoważenia ładunku
Przed każdym wirowaniem, aby uniknąć nadmiernych
drgań oraz jednorodnie rozłożyć wsad, bęben wyko-
nuje obroty z prędkością nieco większą niż podczas
prania. Jeśli pomimo kolejnych prób wsad nie zostanie
równomiernie rozłożony, maszyna wykona wirowanie
z prędkością mniejszą od przewidzianej. W przypad-
ku nadmiernego niezrównoważenia pralka wykona
rozłożenie wsadu zamiast wirowania. Aby zapewnić leps-
ze rozłożenie wsadu oraz jego właściwe zrównoważenie,
zaleca się wymieszanie dużych i małych sztuk bielizny.
1 / 1

HOTPOINT/ARISTON WMSD 723B EU Руководство пользователя

Категория
Стиральные машины
Тип
Руководство пользователя

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ

Спросите документ