Yamaha NS-P220 Инструкция по применению

Бренд: Yamaha

Модель: NS-P220

Категория: Саундбары (акустические колонки)

Тип: Инструкция по применению

NS-P220

HOME CINEMA 5.1CH SPEAKER PACKAGE

OWNER’S MANUAL

U B

• Explanation of Graphical Symbols

The lightning flash with arrowhead

symbol, within an equilateral triangle,

is intended to alert you to the

presence of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert

you to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

SAFETY INSTRUCTIONS

1 Read Instructions – All the safety and operating

instructions should be read before the unit is operated.

2 Retain Instructions – The safety and operating

instructions should be retained for future reference.

3 Heed Warnings – All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and other

instructions should be followed.

5 Water and Moisture – The unit should not be used near

water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a

swimming pool, etc.

6 Carts and Stands – The unit should be used only with

a cart or stand that is recommended by the

manufacturer.

6A A unit and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause

the unit and cart combination to overturn.

7 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

8 Ventilation – The unit should be situated so that its

location or position does not interfere with its proper

ventilation. For example, the unit should not be

situated on a bed, sofa, rug, or similar surface, that

may block the ventilation openings; or placed in a built-

in installation, such as a bookcase or cabinet that may

impede the flow of air through the ventilation openings.

9 Heat – The unit should be situated away from heat

sources such as radiators, stoves, or other appliances

that produce heat.

10 Power Sources – The unit should be connected to a

power supply only of the type described in the

operating instructions or as marked on the unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

IMPORTANT

Please record the serial number of this system in the

space below.

Model:

Serial No.:

The serial number is located on the rear of the main

unit.

Retain this Owner’s Manual in a safe place for future

reference.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

11 Power-Cord Protection – Power-supply cords should

be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the

unit.

12 Cleaning – The unit should be cleaned only as

recommended by the manufacturer.

13 Lightning – For added protection for this unit during a

lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall

outlet and disconnect the antenna or cable system.

This will prevent damage to the unit due to lightning

and power-line surges.

14 Object and Liquid Entry – Care should be taken so that

objects do not fall into and liquids are not spilled into

the inside of the unit.

15 Damage Requiring Service – The unit should be

serviced by qualified service personnel when:

A. The power-supply cord or the plug has been

damaged; or

B. Objects have fallen, or liquid has been spilled into

the unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or

exhibits a marked change in performance; or

E. The unit has been dropped, or the cabinet

damaged.

16 Servicing – The user should not attempt to service the

unit beyond those means described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

17 Power Lines – An outdoor antenna should be located

away from power lines.

18 Grounding or Polarization – Precautions should be

taken so that the grounding or polarization is not

defeated.

III

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most out

of your equipment by playing it at a safe level. One that lets

the sound come through loud and clear without annoying

blaring or distortion – and, most importantly, without

affecting your sensitive hearing.

Since hearing damage from loud sounds is

often undetectable until it is too late, YAMAHA

and the Electronic Industries Association’s

Consumer Electronics Group recommend you

to avoid prolonged exposure from excessive

volume levels.

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the

USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies

and, if not installed and used according to the

instructions found in the users manual, may cause

interference harmful to the operation of other

electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this

product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

● Audio connection cord

● Speaker cords

● Mounting brackets

● Screws

● Main and rear speakers

● Center speaker

● Subwoofer

UNPACKING After unpacking, check that the following items are contained.

(A)

(B)

[4m]

[15m]

(A)

(B)

(C)

X 3

X 2

X 5

X 8

X 2

X 3

X 2

<NX-220P><NX-220P><NX-220P><NX-220P>

<NX-C220>

<SW-P201>

●

To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

●

Install the speakers in a cool, dry, clean place – away from

windows, heat sources, sources of excessive vibration,

dust, moisture and cold. Avoid sources of humming

(transformers, motors). To prevent fire or electrical shock,

do not expose the speakers to rain or water.

● To prevent the enclosure from warping or discoloring, do

not place the speakers where they will be exposed to

direct sunlight or excessive humidity.

● Do not place the following objects on the speakers:

Glass, china, etc.

If glass etc. falls by vibrations and breaks, it may cause

personal injury.

A burning candle etc.

If the candle falls by vibrations, it may cause fire and

personal injury.

A vessel with water in it

If the vessel falls by vibrations and water spills, it may

cause damage to the speakers, and/or you may get an

electric shock.

● Do not place the speakers where foreign objects such as

water drips might fall. It might cause a fire, damage to

the speakers, and/or personal injury.

● Do not place the speakers where they are liable to be

knocked over or struck by falling objects. Stable

placement will also ensure better sound performance.

● Placing the speakers on the same shelf or rack as the

turntable can result in feedback.

● Any time you note distortion, reduce the volume control

on your amplifier to a lower setting. Never allow your

amplifier to be driven into “clipping”. Otherwise the

speakers may be damaged.

●

When using an amplifier with a rated output power higher

than the nominal input power of the speakers, care should

be taken never to exceed the speakers’ maximum input.

● As these speakers contain strong magnets (though all of

them are magnetically shielded types), avoid placing

watches, magnetic tapes, etc. near them. Also, placing

the speakers near a TV set may impair picture color. If

this happens, move the speakers away from the TV set.

●

Do not attempt to clean the speakers with chemical solvents

as this might damage the finish. Use a clean, dry cloth.

● Secure placement or installation is the owner’s

responsibility.

YAMAHA shall not be liable for any accident caused

by improper placement or installation of speakers.

For SW-P201 only

● Never open the cabinet. If something drops into the set,

contact your dealer.

● Do not use force on switches, controls or connection

wires. When moving the unit, first disconnect the power

plug and the wires connected to other equipments.

Never pull the wires themselves.

● Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding

that the unit is faulty.

CAUTION: Read this before operating your unit.

Thank you for selecting this YAMAHA NS-P220 Speaker Package.

● When not planning to use this unit for a long period (ie.,

vacation, etc.), disconnect the AC power plug from the

wall outlet.

●

To prevent lightning damage, disconnect the AC power

plug when there is an electric storm.

● Since this unit has a built-in power amplifier, heat will

radiate from the rear panel. Place the unit apart from the

walls, allowing enough space above, behind and on the

both sides of the unit to prevent fire or damage.

Furthermore, do not position with the rear panel facing

down on the floor or other surfaces.

Be sure to allow a space of at least 20 cm above, behind

and on both sides of the unit.

● Super-bass frequencies reproduced by this unit may

cause a turntable to generate a howling sound. In such a

case, move this unit away from the turntable.

● If you hear distorted noise (i.e., unnatural, intermittent

“rapping” or “hammering” sounds) coming from this unit,

reduce the volume level. Extremely loud playing of a

movie soundtrack’s low frequency, bass-heavy sounds or

similarly loud popular music passages can damage this

speaker system.

● VOLTAGE SELECTOR

(General model only)

The VOLTAGE SELECTOR on the

rear panel of this unit must be set

for your local main voltage

BEFORE plugging into the AC

main supply.

Voltages are 110-120/220-240 V

AC, 50/60 Hz.

Standby mode

If the POWER switch is set to the ON position and the

AUTO STANDBY switch is set to the HIGH or LOW

position, this unit turns into the standby mode when no

signal is inputted to this unit.

In this state, this unit is designed to consume a very

small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

VOLTAGE

SELECTOR

220V-240V

110V-120V

For Canadian Customers

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

CONTENTS

SAFETY INSTRUCTIONS ..............................II

UNPACKING ..................................................IV

CAUTION .........................................................1

COMPONENTS OF THE PACKAGE .............. 2

SETTING UP THE SPEAKERS ...................... 3

Placing the subwoofer ................................... 3

Mounting the main and center speakers .......... 4

Mounting the rear speakers............................ 5

CONNECTIONS.............................................. 6

An example of basic connections .................... 6

How to connect speaker cords to the input

and output terminals of the speakers............... 8

Connecting the subwoofer to speaker output

terminals of the amplifier

................................ 9

USING THE SUBWOOFER (SW-P201)........ 10

Controls and their functions.......................... 10

Adjusting the subwoofer before use ................ 11

ADVANCED YAMAHA ACTIVE SERVO

TECHNOLOGY (for SW-P201) .................... 12

TROUBLESHOOTING.................................. 13

SPECIFICATIONS ........................................ 14

COMPONENTS OF THE PACKAGE

2-way acoustic-suspension speaker system

2-way acoustic-suspension speaker system

Active Servo Processing Subwoofer System with a

built-in power amplifier

● This subwoofer system employs Advanced YAMAHA

Active Servo Technology which YAMAHA has developed

for reproducing higher quality super-bass sound. (Refer to

page 12 for details on Advanced YAMAHA Active Servo

Technology.) This super-bass sound adds a more

realistic, theater-in-the-home effect to your stereo system.

● This subwoofer can be easily added to your existing

audio system by connecting to either the speaker

terminals or the line output (pin jack) terminals of the

amplifier.

● The AUTO STANDBY switch saves you the trouble of

setting the POWER switch to the ON or OFF position.

The speaker package “NS-P220” is designed for use in a

multi-channel audio system such as a home theater system.

The package includes two pairs of main/rear speakers (NX-

220P), a center speaker (NX-C220) and a subwoofer

system (SW-P201).

SPECIAL INSTRUCTIONS FOR U.K. MODEL

IMPORTANT:

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L

or coloured RED. Making sure that neither core is

connected to the earth terminal of the three pin plug.

For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous if

engaged in a live socket outlet.

m Placing the subwoofer

It is recommended to place the subwoofer on the outside of

either the right or the left main speaker. (See fig. Å .) The

placement shown in fig. ı is also possible, however, if the

subwoofer system is placed directly facing the wall, the

bass effect may die because the sound from it and the

sound reflected by the wall may cancel out each other. To

prevent this from happening, face the subwoofer system at

an angle as shown in fig. Å.

Note

There may be a case that you cannot obtain enough super-

bass sounds from the subwoofer when listening in the

center of the room. This is because “standing waves” have

been developed between two parallel walls and they cancel

the bass sounds.

In such a case, face the subwoofer obliquely to the wall. It

also may be necessary to break up the parallel surfaces by

placing bookshelves etc. along the walls.

( : Subwoofer, : Main speaker)

SETTING UP THE SPEAKERS

Before making connections, place all speakers in their respective positions. The positioning of the speakers is important

because it controls the whole sound quality of this system.

Place the speakers depending on your listening position by following the instructions below.

Speaker configuration

This speaker package employs a 6 speaker configuration: 2

main speakers, 2 rear speakers, a center speaker and a

subwoofer.

The main speakers are used for main source sound. The

rear speakers are used for surround sounds, and the center

speaker is for center sounds (dialog etc.). The subwoofer is

for reinforcing low frequencies on your audio system.

Note

In this speaker package, the same speakers (NX-220P) are

used for the main and rear speakers.

Placing speakers

Main speakers: On both sides of and at approximately

the same height as the TV set.

Rear speakers: Behind your listening position, facing

slightly inward. About 1.8 m (approx. 6

feet) from the floor.

Center speaker: Precisely between the main speakers.

Subwoofer: The position of the subwoofer is not so

critical because low bass tones are not

highly directional.

Refer to “Placing the subwoofer” below

for a recommended positioning of the

subwoofer.

Main L Center Main R

Rear L

Subwoofer

Rear R

Main L

Main R

Subwoofer

Center

Rear L

Rear R

TV-set

Place the main speakers on a rack or on a shelf. Place the

center speaker on top of the TV, on a shelf or inside the TV

rack so that it is stable.

To obtain more stability and usefulness, we recommend that

you mount these speakers on the provided mounting

brackets (type A).

To mount the speakers on the mounting

brackets (type A)

1 Attach the bracket to the bottom of the speaker by using

the provided screw (type A).

2 Turn and/or slide the speaker on the bracket according

to your preference, and then tighten the screw.

Note

Though this speaker is a magnetically shielded type,

there may be some influence on a TV picture depending

on the type of TV or the placement of the speaker. In

such a case, place the speaker apart from TV so that

there is no influence on TV picture.

m Mounting the main and center speakers

The provided mounting bracket (type C) with 1 pair of

screw holes (at an interval of 60 mm) can be used to

mount the speaker on a speaker stand.

* Those screw holes can be used with M4 screws only.

1 Attach the bracket to the bottom of the speaker by

using the provided screw (type A) so that the convex

part of the bracket fits in the grooved part on the

bottom of the speaker as shown on the left.

2 Mount the speaker on the speaker stand by using the

screw holes on the bracket.

Note

The mounting bracket (type C) is provided for each of 5

speakers.

If you want to mount a speaker on a commercially available speaker stand

(for the main/center/rear speakers)

Mounting

bracket

(type A)

Screw

(type A)

Mounting

bracket

(type C)

Screw

(type A)

60 mm

Mount the rear speakers on a shelf, rack or directly on the

floor, or hang them on the wall.

To mount the rear speakers on a wall by

using the provided mounting brackets

(type B)

Note

It is recommended that you connect the speaker cords to

the speaker’s terminals before attaching the bracket to the

speaker.

1 Attach the bracket to the bottom of the speaker by using

the provided screw (type B).

2 Turn and/or slide the speaker on the bracket according

to your preference, and then, tighten the screw.

3 Fasten screws into a firm wall or wall support as shown

in the figure, and hang the holes of the mounting

bracket on the protruding screws.

* Make sure that the screws are securely caught by the

narrow parts of the holes.

Note

If desired, you can hang the speaker directly on the

protruding screws on the wall without using the bracket.

WARNING

● Each speaker weighs 0.7 kg (1 lbs. 9 oz.). Do not

mount them on thin plywood or a wall with soft

surface material. If mounted, the screws may come

out of the flimsy surface and the speakers may fall.

This damages the speakers or causes personal

injury.

● Do not install the speakers to a wall with nails,

adhesives, or any other unstable hardware. Long-

term use and vibrations may cause them to fall.

● To avoid accidents resulting from tripping over loose

speaker cords, fix them to the wall.

● Select a proper position on the wall to mount the

speaker and the bracket so that no one will injure his/

her head or face with the edge of the bracket.

m Mounting the rear speakers

Mounting

bracket

(type B)

Screw

(type B)

Mounting

bracket

(type B)

Wall/ wall

support

Tapping screw

(Available at the

hardware store)

Min.

20 mm

65 mm

CONNECTIONS

Caution: Plug in the subwoofer and other audio/video components after all connections are

completed.

m An example of basic connections

SPEAKERS

MAIN CENTER REAR

(SURROUND)

OUTPUT

SUB

WOOFER

CAUTION

SEE INSTRUCTION

MANUAL FOR CORRECT SETTING.

MAIN

CENTER REAR

(SURROUND)

/MONO

VOLUME

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

AUTO

STANDBY

STANDBY-RED

ON-GREEN

OFF

LOW

HIGH

OFF

POWER

0I0

INPUT2

/MONO

REAR R

REAR L

REAR R

CENTER

REAR L

CENTER

FRONT R

FRONT L

LeftRight

Subwoofer

Amplifier

To AC outlet

Center speaker

Rear speakers

LeftRight

Main speakers

● Connect the main, center and rear speakers to the

speaker output terminals of your amplifier with the

provided speaker cords.

* The provided speaker cords have labels marked

FRONT L, FRONT R, CENTER, REAR L or REAR R.

Connect each speaker cord to the corresponding

speaker by following the figure on page 6.

* Connect each speaker making sure not to reverse the

polarity (+, –). If the speaker is connected with

reversed polarity, the sound will be unnatural and lack

bass.

* For the main and rear speakers only, connect one

speaker to the left (marked L) terminals of your

amplifier, and another speaker to the right (marked R)

terminals.

● Basically, connect the subwoofer to the line output (pin

jack) terminal(s) of the amplifier. If your amplifier does

not have any line output terminal, connect the subwoofer

to the speaker output terminals of the amplifier. (Refer to

page 9 for details.)

* To connect with a YAMAHA DSP amplifier (or AV

receiver), connect the SUBWOOFER (or LOW PASS

etc.) terminal on the rear of the DSP amplifier (or AV

receiver) to the L/MONO INPUT2 terminal of the

subwoofer.

* To connect the subwoofer to the SPLIT SUBWOOFER

terminals on the rear of the DSP amplifier, connect

them to both the left L and right R INPUT2 terminals

of the subwoofer.

Note

When connecting to a monaural line output terminal of the

amplifier, connect the L/MONO INPUT2 terminal.

Main/center/rear speakers

One side of the provided speaker cord has a white broken

line and the other side has no line.

Connect the (+) terminals on both the speaker and the

amplifier using the side with a white broken line. Connect

the (–) terminals on both components using the side with no

line.

Red: positive (+)

Black: negative (–)

Subwoofer (INPUT1/OUTPUT terminals)

Connect the (+) terminals on both the subwoofer and the

amplifier using one side of the cord. Connect the (–)

terminals on both components using the other side of the

cord.

Red: positive (+)

Black: negative (–)

m How to connect speaker cords to the input and output terminals

of the speakers

For connections, keep the speaker cords as short as possible. Do not bundle or roll up the excess part of the cords. If the

connections are faulty, no sound will be heard from the speakers.

10 mm

How to Connect:

1 Press and hold the terminal’s tab, as shown in the

figure.

2 Insert the bare wire end properly into the terminal hole.

[Remove approx. 10 mm (3/8”) insulation from the

speaker cord.]

3 Release your finger from the tab to allow it to lock

securely on the cord’s wire end.

4 Test the firmness of the connection by pulling lightly on

the cord at the terminal.

Note

Do not let the bare speaker wires touch each other as

this could damage the speaker or the amplifier, or both

of them.

White broken line

m Connecting the subwoofer to speaker output terminals of the

amplifier

If your amplifier has only one set of main speaker output terminals

Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT

terminals of the subwoofer to the main speakers.

Left main

speaker

Right main

speaker

Subwoofer

Amplifier

Speaker

output

terminals

To AC outlet

If your amplifier has two sets of speaker output terminals

(Both A and B speaker outputs

must be ON.)

Subwoofer

Amplifier

Speaker output terminals

To AC outlet

/MONO

VOLUME

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

AUTO

STANDBY

STANDBY-RED

ON-GREEN

OFF

LOW

HIGH

OFF

POWER

0I0

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

/MONO

VOLUME

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

AUTO

STANDBY

STANDBY-RED

ON-GREEN

OFF

LOW

HIGH

OFF

POWER

0I0

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

Left main

speaker

Right main

speaker

USING THE SUBWOOFER (SW-P201)

1 POWER switch

Set this switch to the ON position to turn on the power

of the subwoofer. When the power of the subwoofer is

on, the power indicator below the POWER switch lights

up GREEN. Set this switch to the OFF position to turn

off the power of the subwoofer.

2 Power indicator

Lights up GREEN when the POWER switch is set to

the ON position and goes off when set to the OFF

position.

* Standby mode

If the POWER switch is set to the ON position and

the AUTO STANDBY switch is set to the HIGH or

LOW position, this indicator lights up RED when no

signal is inputted to the subwoofer.

3 AUTO STANDBY (HIGH/LOW/OFF) switch

By setting this switch to the HIGH or LOW position, the

subwoofer’s automatic power-switching function

operates as described on the next page. If you do not

need this function, set to the OFF position.

* Make sure to change the setting of this switch only

when the POWER switch (1) is in the OFF

position.

Standby mode

The subwoofer is still using a small amount of power

in this mode.

4 INPUT2 terminals

Used to input line level signals from the amplifier.

5 INPUT1 (FROM AMPLIFIER) terminals

Used to connect the subwoofer with the speaker

terminals of the amplifier.

6 OUTPUT (TO SPEAKERS) terminals

Can be used for connecting to the main speakers.

Signals from the INPUT1 terminals (5) are sent to

these terminals.

7 VOLUME control

Adjusts the volume level.

8 VOLTAGE SELECTOR switch (General model only)

If the preset setting of the switch is incorrect, set the

switch to the proper voltage range (220V-240V or

110V-120V) of your area.

Consult your dealer if you are unsure of the correct

setting.

WARNING

Be sure to unplug the subwoofer before setting the

VOLTAGE SELECTOR switch correctly.

Rear panel

m Controls and their functions

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

/MONO

AUTO

STANDBY

STANDBY-RED

ON-GREEN

OFF

LOW

HIGH

OFF

POWER

VOLUME

0I0

OFF

POWER

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

/MONO

AUTO

STANDBY

STANDBY-RED

ON-GREEN

OFF

LOW

HIGH

VOLUME

0I0

VOLTAGE

SELECTOR

220V-240V

110V-120V

VOLTAGE

SELECTOR

220V-240V

110V-120V

1 Set the VOLUME control to minimum (0).

2 Turn on the power supply to all the

components.

3 Play a source and adjust the amplifier’s

volume control to the desired listening level.

4 Increase the volume gradually to adjust the

volume balance between the subwoofer and

the main speakers.

Note: It is recommended to set the

VOLUME control to the middle

position when using all the

speakers of this package in a 5.1-

channel home theater system.

䡵 Adjusting the subwoofer before use

Before using the subwoofer, adjust the subwoofer to obtain the optimum volume balance between the subwoofer and the main

speakers by following the procedures described below.

Rear panel

Once the volume balance between the subwoofer and

the main speakers is adjusted, you can adjust the

volume of your whole sound system by using the

amplifier’s volume control.

However, if you change the main speakers NX-220P to

others, you must make this adjustment again.

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT2

/MONO

AUTO

STANDBY

STANDBY-RED

ON-GREEN

OFF

LOW

HIGH

OFF

POWER

VOLUME

0I0

OFF

POWER

AUTO

STANDBY

STANDBY-RED

ON-GREEN

OFF

LOW

HIGH

VOLUME

0I0

1, 4

VOLUME

0I0

Automatic power-switching function

If the source being played is stopped and the input signal is

cut off for 7 to 8 minutes, the subwoofer automatically

switches to the standby mode. (When the subwoofer

switches to the standby mode, the power indicator lights up

in red.)

When you play a source again, the power of the subwoofer

turns on automatically by sensing audio signals input to the

subwoofer.

This function operates by sensing a certain level of low

frequency input signal. Usually set the AUTO STANDBY

switch to the LOW position. However, if the power is not

switched to ON or STANDBY smoothly, set the switch to the

HIGH position. In the HIGH position, the power will turn on

even with a low level of input signal. But please be aware

that the subwoofer may not switch to the standby mode

when there is an extremely low input signal.

* The power might turn on unexpectedly by sensing noise

from other appliances. If that occurs, set the AUTO

STANDBY switch to the OFF position and use the

POWER switch to switch the power between ON and

OFF manually.

* This function detects the low-frequency components

below 200 Hz of the input signals (i.e., the explosion in

the action movie, the sound of the bass guitar or the

bass drum, etc.).

* The minutes required to switch the subwoofer to the

standby mode might change by sensing noise from

other appliances.

This function is available only when the power of the

subwoofer is on (by setting the POWER switch (

1) to

“ON”).

ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY

(for SW-P201)

The theory of Yamaha Active Servo Technology has been

based upon two major factors, the Helmholtz resonator and

negative-impedance drive. Active Servo Processing

speakers reproduce the bass frequencies through an “air

woofer”, which is a port or opening in the speaker’s cabinet.

This opening is used instead of, and performs the functions

of, a woofer in a conventionally designed speaker system.

Thus, signals of low amplitude within the cabinet can,

according to the Helmholtz resonance theory, be outputted

from this opening as waves of great amplitude if the size of

the opening and the volume of the cabinet are in the correct

proportion to satisfy a certain ratio.

In order to accomplish this, moreover, the amplitudes within

the cabinet must be both precise and of sufficient power

because these amplitudes must overcome the “load”

presented by the air that exists within the cabinet.

Thus it is this problem that is resolved through the

employment of a new design in which the amplifier supplies

special signals. If the electrical resistance of the voice coil

could be reduced to zero, the movement of the speaker unit

would become linear with respect to signal voltage. To

accomplish this, a special negative-impedance output-drive

amplifier for subtracting output impedance of the amplifier is

used.

By employing negative-impedance drive circuits, the

amplifier is able to generate precise, low-amplitude, low-

frequency waves with superior damping characteristics.

These waves are then radiated from the cabinet opening as

high-amplitude signals. The system can, therefore, by

employing the negative-impedance output drive amplifier

and a speaker cabinet with the Helmholtz resonator,

reproduce an extremely wide range of frequencies with

amazing sound quality and less distortion.

The features described above, then, are combined to be the

fundamental structure of the conventional Yamaha Active

Servo Technology.

Our new Active Servo Technology — Advanced Yamaha

Active Servo Technology — adopted Advanced Negative

Impedance Converter (ANIC) circuits, which allows the

conventional negative impedance converter to dynamically

vary in order to select an optimum value for speaker

impedance variation. With this new ANIC circuits, Advanced

Yamaha Active Servo Technology can provide more stable

performance and improved sound pressure compared with

the conventional Yamaha Active Servo Technology, resulting

in more natural and dynamic bass reproduction.

High-amplitude

bass sound

Cabinet

Port

Air woofer

(Helmholtz resonator)

Active Servo

Processing

Amplifier

Signals

Signals of low amplitude

Advanced Negative-

impedance Converter

Problem

Power is not supplied even

though the POWER switch is set

to the ON position.

No sound.

Sound level is too low.

The subwoofer will not turn on

automatically.

The subwoofer turns into the

standby mode unexpectedly.

The subwoofer turns on

unexpectedly.

What to Do

Connect it securely.

Turn the VOLUME control to the right.

Connect them securely.

Connect them correctly, that is L (left) to

L, R (right) to R, “+” to “+” and “–” to “–”.

Play a source sound with bass

frequencies.

Reposition the subwoofer or break up

the parallel surface by placing

bookshelves etc. along the walls.

Set the POWER switch to the ON

position.

Set the AUTO STANDBY switch to the

“HIGH” or “LOW” position.

Set the AUTO STANDBY switch to the

“HIGH” position.

Set the AUTO STANDBY switch to the

“HIGH” position.

Move the subwoofer farther away from

such appliances and/or reposition the

connected speaker cables.

Otherwise, set the AUTO STANDBY

switch to the “OFF” position.

Cause

The power plug is not securely

connected.

The VOLUME control is set to 0.

Speaker cords are not connected

securely.

Speaker cords are not connected

correctly.

A source sound with few bass

frequencies is played.

It is influenced by standing waves.

The POWER switch is set to the OFF

position.

The AUTO STANDBY switch is set to

the OFF position.

The level of input signal is too low.

There is an influence of noise

generated from external appliances etc.

TROUBLESHOOTING

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if

the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service

center.

Problem

No sound.

Sound level is too low.

What to Do

Connect them securely.

Connect them correctly, that is L (left) to

L, R (right) to R, “+” to “+” and “–” to “–”.

Cause

Speaker cords are not connected

securely.

Speaker cords are not connected

correctly.

For SW-P201

SPECIFICATIONS

NX-220P, NX-C220

Type ............... 2-way acoustic-suspension speaker system

Magnetically shielded type

Driver............................................. 8 cm (3-1/8”) cone type

1.9 cm (3/4”) balanced dome type

Nominal Input Power ................................................. 30W

Maximum Input Power ............................................. 100W

Impedance .....................................................................6Ω

Frequency Response................................ 140 Hz–27 kHz

Sensitivity ...................................................86 dB/2.83V/m

Dimensions (W x H x D)

<NX-220P>........................ 100 mm x 140 mm x 113 mm

(3-15/16” x 5-1/2” x 4-7/16”)

<NX-C220> .......................140 mm x 100 mm x 112 mm

(5-1/2” x 3-15/16”x 4-7/16”)

Weight

<NX-220P>.................................. 0.7 kg (1 lbs. 9 oz.) x 4

<NX-C220> ....................................... 0.7 kg (1 lbs. 9 oz.)

SW-P201

Type ............... Advanced Yamaha Active Servo Technology

Driver...................... 16 cm (6-5/16”) cone woofer (JA1678)

Magnetically shielded type

Amplifier Output.................................................... 50W/5Ω

Frequency Response................... 30 Hz–200 Hz (–10 dB)

Power Supply

USA and Canada models .......................AC 120V, 60 Hz

U.K. and Europe models ........................ AC 230V, 50 Hz

Australia model.......................................AC 240V, 50 Hz

General model.............. AC 110-120/220-240V, 50/60 Hz

Power Consumption ...................................................42W

(In the standby mode: 6W)

Dimensions (W x H x D)...... 200 mm x 395 mm x 384 mm

(7-7/8” x 15-9/16” x 15-1/8”)

Weight .................................................9.3 kg (20 lbs. 7 oz.)

Accessories ............................... Audio connection cord x 1

Speaker cord [4 m (13.1 feet)] x 3

Speaker cord [15 m (49.2 feet)] x 2

Mounting bracket (type A) x 3

Mounting bracket (type B) x 2

Mounting bracket (type C) x 5

Screw (type A) x 8

Screw (type B) x 2

* Please note that all specifications are subject to change

without notice.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

V742370-1

Printed in China

Yamaha NS-P220 Инструкция по применению

Бренд: Yamaha

Модель: NS-P220

Категория: Саундбары (акустические колонки)

Тип: Инструкция по применению

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha NS-P220 Owner's manual
français: Yamaha NS-P220 Le manuel du propriétaire
italiano: Yamaha NS-P220 Manuale del proprietario
español: Yamaha NS-P220 El manual del propietario
Deutsch: Yamaha NS-P220 Bedienungsanleitung
Nederlands: Yamaha NS-P220 de handleiding
português: Yamaha NS-P220 Manual do proprietário
dansk: Yamaha NS-P220 Brugervejledning
polski: Yamaha NS-P220 Instrukcja obsługi
čeština: Yamaha NS-P220 Návod k obsluze
svenska: Yamaha NS-P220 Bruksanvisning
Türkçe: Yamaha NS-P220 El kitabı
suomi: Yamaha NS-P220 Omistajan opas
română: Yamaha NS-P220 Manualul proprietarului

Yamaha NS-P220 Инструкция по применению

Yamaha NS-P220 Инструкция по применению

на других языках

Похожие модели бренда