ASROCK H110M-DVS/D3 Руководство пользователя

Version 1.0

Published July 2015

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this documentation may or may not

be registered trademarks or copyrights of their respective companies, and are used

only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for

informational use only and subject to change without notice, and should not be

constructed as a commitment by ASRock. ASRock assumes no responsibility for

any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide

warranty of any kind, either expressed or implied, including but not limited to

the implied warranties or conditions of merchantability or tness for a particular

purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of prots, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance

controlled in Perchlorate Best Management Practices (BMP) regulations passed by the

California Legislature. When you discard the Lithium battery in California, USA, please

follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/

perchlorate”

ASRock Website: http://www.asrock.com

1

English

H110M-DVS/D3

Intel

H110

DDR3_B1 (64 bit, 240-pin module)

DDR3_A1 (64 bit, 240-pin module)

CMOS

Battery

Super

I/O

ATXPWR1

Top:

RJ-45

USB 2.0

T: USB0

B: USB1

CLRCMOS1

1

HDLED RESET

PLED PWRBTN

PANEL1

1

USB4_5

COM1

1

HD_AUDIO1

H110M-DVS/D3

CHA_FAN1

RoHS

7

9

12

16

15

2

CPU_FAN1

3

4

6

5

1

128Mb

BIOS

Audio

CODEC

PCIE1

PCI Express 3.0

TPMS1

1

USB3_4_5

PCIE3

USB 2.0

T: USB2

B: USB3

Top:

LINE I N

Cent er:

FRON T

Bott om:

MIC IN

1

ATX 12V1

USB 3.0

T: USB0

B: USB1

PS2

Keyboard

/Mouse

SPK_CI1

1

PCIE2

Front USB 3.0

8

10

11

13

14

17

VGA1

DVI1

SATA3 _0 S ATA3_2

SATA3 _1 S ATA3_3

Motherboard Layout

2

English

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 CPU Fan Connector (CPU_FAN1)

3 2 x 240-pin DDR3/DDR3L DIMM Slots (DDR3_A1, DDR3_B1)

4 ATX Power Connector (ATXPWR1)

5 USB 3.0 Header (USB3_4_5)

6 SATA3 Connector (SATA3_2)

7 SATA3 Connector (SATA3_3)

8 SATA3 Connector (SATA3_1)

9 SATA3 Connector (SATA3_0)

10 Clear CMOS Jumper (CLRMOS1)

11 System Panel Header (PANEL1)

12 USB 2.0 Header (USB4_5)

13 Chassis Intrusion and Speaker Header (SPK_CI1)

14 TPM Header (TPMS1)

15 COM Port Header (COM1)

16 Chassis Fan Connector (CHA_FAN1)

17 Front Panel Audio Header (HD_AUDIO1)

3

English

H110M-DVS/D3

I/O Panel

No. Description No. Description

1 PS/2 Mouse/Keyboard Port 6 Microphone (Pink)**

2 D-Sub Port (VGA1) 7 USB 2.0 Ports (USB01)

3 LAN RJ-45 Port* 8 USB 2.0 Ports (USB_23)

4 Line In (Light Blue)** 9 DVI-D Port

5 Front Speaker (Lime)** 10 USB 3.0 Ports (USB3_01)

6

7

8

9

3

5

4

10

1

2

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection

Blinking Data Activity Orange 100Mbps connection

On Link Green 1Gbps connection

ACT/LINK LED

SPEED LED

LAN Port

4

English

** To congure 7.1 CH HD Audio, it is required to use an HD front panel audio module and enable the multi-

channel audio feature through the audio driver.

Please set Speaker Conguration to “7.1 Speaker”in the Realtek HD Audio Manager.

Function of the Audio Ports in 7.1-channel Conguration:

Port Function

Light Blue (Rear panel) Rear Speaker Out

Lime (Rear panel) Front Speaker Out

Pink (Rear panel) Central /Subwoofer Speaker Out

Lime (Front panel) Side Speaker Out

5

English

H110M-DVS/D3

1 Introduction

ank you for purchasing ASRock H110M-DVS/D3 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control.

It delivers excellent performance with robust design conforming to ASRock’s

commitment to quality and endurance.

1.1 Package Contents

• ASRock H110M-DVS/D3 Motherboard (Micro ATX Form Factor)

• ASRock H110M-DVS/D3 Quick Installation Guide

• ASRock H110M-DVS/D3 Support CD

• 2 x Serial ATA (SATA) Data Cables (Optional)

• 1 x I/O Panel Shield

Because the motherboard specications and the BIOS soware might be updated, the

content of this documentation will be subject to change without notice. In case any modi-

cations of this documentation occur, the updated version will be available on ASRock’s

website without further notice. If you require technical support related to this mother-

board, please visit our website for specic information about the model you are using. You

may nd the latest VGA cards and CPU support list on ASRock’s website as well. ASRock

website http://www.asrock.com.

6

English

1.2 Specications

Platform

• Micro ATX Form Factor

• Solid Capacitor design

• High Density Glass Fabric PCB

CPU

• Supports 6

th

Generation Intel® Core

TM

i7/i5/i3/Pentium®/

Celeron® Processors (Socket 1151)

• Supports Intel® Turbo Boost 2.0 Technology

Chipset

• Intel® H110

Memory

• Dual Channel DDR3/DDR3L Memory Technology

• 2 x DDR3/DDR3L DIMM Slots

• Supports DDR3/DDR3L 1600/1333/1066 non-ECC, un-

buered memory

• Max. capacity of system memory: 32GB

• Supports Intel® Extreme Memory Prole (XMP) 1.3 / 1.2

Expansion

Slot

• 1 x PCI Express 3.0 x16 Slot (PCIE1: x16 mode)

• 2 x PCI Express 2.0 x1 Slots

Graphics

* Intel® HD Graphics Built-in Visuals and the VGA outputs can

be supported only with processors which are GPU integrated.

• Supports Intel® HD Graphics Built-in Visuals : Intel® Quick

Sync Video with AVC, MVC (S3D) and MPEG-2 Full

HW Encode1, Intel® InTru

TM

3D, Intel® Clear Video HD

Technology, Intel® Insider

TM

, Intel® HD Graphics 510/530

• Pixel Shader 5.0, DirectX 12

• Max. shared memory 1792MB

• Dual graphics output: Support DVI-D and D-Sub ports by

independent display controllers

• Supports DVI-D with max. resolution up to 1920x1200 @

60Hz

• Supports D-Sub with max. resolution up to 1920x1200 @

60Hz

7

English

H110M-DVS/D3

• Supports Accelerated Media Codecs: HEVC, VP8, VP9

• Supports HDCP with DVI-D Port

• Supports Full HD 1080p Blu-ray (BD) playback with DVI-D

Port

Audio

• 7.1 CH HD Audio (Realtek ALC887 Audio Codec)

* To congure 7.1 CH HD Audio, it is required to use an HD

front panel audio module and enable the multi-channel audio

feature through the audio driver.

• Supports Surge Protection (ASRock Full Spike Protection)

• ELNA Audio Caps

LAN

• PCIE x1 Gigabit LAN 10/100/1000 Mb/s

• Realtek RTL8111E

• Supports Wake-On-LAN

• Supports Lightning/ESD Protection (ASRock Full Spike

Protection)

• Supports LAN Cable Detection

• Supports Energy Ecient Ethernet 802.3az

• Supports PXE

Rear Panel

I/O

• 1 x PS/2 Mouse/Keyboard Port

• 1 x D-Sub Port

• 1 x DVI-D Port

• 4 x USB 2.0 Ports (Supports ESD Protection (ASRock Full

Spike Protection))

• 2 x USB 3.0 Ports (Supports ESD Protection (ASRock Full

Spike Protection))

• 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

LED)

• HD Audio Jacks: Line in / Front Speaker / Microphone

Storage

• 4 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and

Hot Plug

8

English

Connector

• 1 x COM Port Header

• 1 x TPM Header

• 1 x Chassis Intrusion and Speaker Header

• 1 x CPU Fan Connector (4-pin) (Smart Fan Speed Control)

• 1 x Chassis Fan Connector (4-pin) (Smart Fan Speed Con-

trol)

• 1 x 24 pin ATX Power Connector

• 1 x 4 pin 12V Power Connector

• 1 x Front Panel Audio Connector

• 1 x USB 2.0 Header (Supports 2 USB 2.0 ports) (Supports

ESD Protection (ASRock Full Spike Protection))

• 1 x USB 3.0 Header (Supports 2 USB 3.0 ports) (Supports

ESD Protection (ASRock Full Spike Protection))

BIOS

Feature

• 128Mb AMI UEFI Legal BIOS with multilingual GUI sup-

port

• ACPI 1.1 Compliant wake up events

• SMBIOS 2.3.1 Support

• CPU, GT_CPU, DRAM, PCH 1.0V, VCCIO, VCCSA Voltage

Multi-adjustment

Hardware

Monitor

• CPU/Chassis temperature sensing

• CPU/Chassis Fan Tachometer

• CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by

CPU temperature)

• CPU/Chassis Fan multi-speed control

• CASE OPEN detection

• Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, CPU

OS

• Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-

bit

* To install Windows® 7 OS, a modied installation disk with

xHCI drivers packed into the ISO le is required. Please refer to

page 62 for more detailed instructions.

* For the updated Windows® 10 driver, please visit ASRock’s

website for details: http://www.asrock.com

9

English

H110M-DVS/D3

Please realize that there is a certain risk involved with overclocking, including adjusting

the setting in the BIOS, applying Untied Overclocking Technology, or using third-party

overclocking tools. Overclocking may aect your system’s stability, or even cause damage to

the components and devices of your system. It should be done at your own risk and expense.

We are not responsible for possible damage caused by overclocking.

* For detailed product information, please visit our website:

http://www.asrock.com

Certica-

tions

• FCC, CE, WHQL

• ErP/EuP ready (ErP/EuP ready power supply is required)

10

English

1.3 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper

is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”

when a jumper cap is placed on these 2 pins.

Clear CMOS Jumper

(CLRMOS1)

(see p.1, No. 10)

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system

parameters to default setup, please turn o the computer and unplug the power

cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to

short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the

CMOS right aer you update the BIOS. If you need to clear the CMOS when you

just nish updating the BIOS, you must boot up the system rst, and then shut it

down before you do the clear-CMOS action. Please be noted that the password,

date, time, and user default prole will be cleared only if the CMOS battery is

removed.

Clear CMOS

Default

If you clear the CMOS, the case open may be detected. Please adjust the BIOS option “Clear

Status” to clear the record of previous chassis intrusion status.

11

English

H110M-DVS/D3

1.4 Onboard Headers and Connectors

System Panel Header

(9-pin PANEL1)

(see p.1, No. 11)

Connect the power

switch, reset switch and

system status indicator on

the chassis to this header

according to the pin

assignments below. Note

the positive and negative

pins before connecting

the cables.

GND

RESET#

PWRBTN#

PLED-

PLED+

GND

HDLED-

HDLED+

1

GND

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may congure the way to turn

o your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart the

computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. e LED is on when the

system is operating. e LED keeps blinking when the system is in S1/S3 sleep state. e

LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. e LED is on when the

hard drive is reading or writing data.

e front panel design may dier by chassis. A front panel module mainly consists of power

switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connect-

ing your chassis front panel module to this header, make sure the wire assignments and the

pin assignments are matched correctly.

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these

headers and connectors. Placing jumper caps over the headers and connectors will cause

permanent damage to the motherboard.

12

English

Chassis Intrusion and

Speaker Header

(7-pin SPK_CI1)

(see p.1, No. 13)

Please connect the

chassis intrusion and the

chassis speaker to this

header.

Serial ATA3 Connectors

(SATA3_0)

(see p.1, No. 9)

(SATA3_1)

(see p.1, No. 8)

(SATA3_2)

(see p.1, No. 6)

(SATA3_3)

(see p.1, No. 7)

ese four SATA3

connectors support SATA

data cables for internal

storage devices with up to

6.0 Gb/s data transfer rate.

USB 2.0 Header

(9-pin USB4_5)

(see p.1, No. 12)

DUMMY

GND

+B

-B

USB_PWR

+A

-A

USB_PWR

1

ere is one header on

this motherboard. Each

USB 2.0 header can

support two ports.

USB 3.0 Header

(19-pin USB3_4_5)

(see p.1, No. 5)

1

IntA_PB_D+

Dummy

IntA_PB_D-

GND

IntA_PB_SSTX+

GND

IntA_PB_SSTX-

IntA_PB_SSRX+

IntA_PB_SSRX-

VbusVbus

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

Besides two USB 3.0 ports

on the I/O panel, there

is one header on this

motherboard. Each USB

3.0 header can support

two ports.

1

+5V

DUMMY

SIGNAL

GND

DUMMY

SPEAKER

DUMMY

SATA3_2

SATA3_3

SATA3_0

SATA3_1

13

English

H110M-DVS/D3

Front Panel Audio Header

(9-pin HD_AUDIO1)

(see p.1, No. 17)

J_SENSE

OUT2_L

1

MIC_RET

PRESENCE#

GN D

OUT2_R

MIC2_R

MIC2_L

OUT_RET

is header is for

connecting audio devices

to the front audio panel.

Chassis Fan Connector

(4-pin CHA_FAN1)

(see p.1, No. 16)

GND

FAN_VOLTAGE

CHA_FAN_SPEED

FAN_SPEED_CONTROL

Please connect fan cables

to the fan connector and

match the black wire to

the ground pin.

CPU Fan Connector

(4-pin CPU_FAN1)

(see p.1, No. 2)

GND

FAN_VOLTAGE

CPU_FAN_SPEED

FAN_SPEED_CONTROL

1 2 3 4

is motherboard pro-

vides a 4-Pin CPU fan

(Quiet Fan) connector.

If you plan to connect a

3-Pin CPU fan, please

connect it to Pin 1-3.

1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis must sup-

port HDA to function correctly. Please follow the instructions in our manual and chassis

manual to install your system.

2. If you use an AC’97 audio panel, please install it to the front panel audio header by the

steps below:

A. Connect Mic_IN (MIC) to MIC2_L.

B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C. Connect Ground (GND) to Ground (GND).

D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to connect

them for the AC’97 audio panel.

E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and

adjust “Recording Volume”.

14

English

ATX Power Connector

(24-pin ATXPWR1)

(see p.1, No. 4)

is motherboard pro-

vides a 24-pin ATX power

connector. To use a 20-pin

ATX power supply, please

plug it along Pin 1 and Pin

13.

ATX 12V Power

Connector

(4-pin ATX12V1)

(see p.1, No. 1)

is motherboard pro-

vides a 4-pin ATX 12V

power connector.

Serial Port Header

(9-pin COM1)

(see p.1, No. 15)

is COM1 header

supports a serial port

module.

TPM Header

(17-pin TPMS1)

(see p.1, No. 14)

is connector supports Trusted

Platform Module (TPM) system,

which can securely store keys,

digital certicates, passwords,

and data. A TPM system also

helps enhance network security,

protects digital identities, and

ensures platform integrity.

1

12

13

24

1

GND

SMB_DATA_MAIN

LAD2

LAD1

GND

S_PWRDWN#

SERIRQ#

GND

PCICLK

PCIRST#

LAD3

+3V

LAD0

+3VSB

GND

FRAME

SMB_CLK_MAIN

CCTS#1

RRTS#1

DDSR#1

DDTR#1

RRXD1

GND

TTXD1

DDCD#1

1

RRI#1

15

H110M-DVS/D3

Deutsch

Technische Daten

Plattform

• Micro-ATX-Formfaktor

• Feststoondensator-Design

• Leiterplatte mit hochdichtem Glasgewebe

Prozessor

• Unterstützt die Prozessoren Intel® Core

TM

i7/i5/i3/Pentium®/

Celeron® der 6. Generation (Sockel 1151)

• Unterstützt Intel® Turbo Boost 2.0-Technologie

Chipsatz

• Intel® H110

Speicher

• Dualkanal-DDR3/DDR3L-Speichertechnologie

• 2 x DDR3/DDR3L-DIMM-Steckplätze

• Unterstützt DDR3/DDR3L 1600/1333/1066 non-ECC,

ungepuerter Speicher

• Systemspeicher, max. Kapazität: 32GB

• Unterstützt Intel® Extreme Memory Prole (XMP)1.3/1.2

Erweiter-

ungssteckplatz

• 1 x PCI-Express 3.0-x16-Steckplatz (PCIE1:x16-Modus)

• 2 x PCI-Express 2.0-x1-Steckplätze

Grakkarte

* Integrierte Intel® HD Graphics-Visualisierung und VGA-

Ausgänge können nur mit Prozessoren unterstützt werden, die

GPU-integriert sind.

• Unterstützt integrierte Intel® HD Graphics-Visualisierung:

Intel® Quick Sync Video mit AVC, MVC (S3D) und MPEG-2

Full HW Encode1, Intel® InTru

TM

3D, Intel® Clear Video HD

Technology, Intel® Insider

TM

, Intel® HD Graphics 510/530

• Pixel Shader 5.0, DirectX 12

• Max. geteilter Speicher: 1792 MB

• Dualer Grakkartenausgang Unterstützt DVI-D- und

D-Sub-Ports durch unabhängige Monitor-Controller

• Unterstützt DVI-D mit maximaler Auösung von 1920 x

1200 bei 60 Hz

• Unterstützt D-Sub mit maximaler Auösung von 1920 x

1200 bei 60 Hz

16

Deutsch

• Unterstützt beschleunigte Mediencodecs: HEVC, VP8, VP9

• Unterstützt HDCP mit DVI-D-Port

• Unterstützt Blu-ray- (BD) Wiedergabe (Full HD/1080p) mit

DVI-D-Port

Audio

• 7.1-Kanal-HD-Audio (Realtek ALC887-Audiocodec)

*Zur Konguration von 7.1-Kanal-HD-Audio müssen Sie ein

HD-Frontblenden-Audiomodul nutzen und den Mehrkanalton

über den Audiotreiber aktivieren.

• Unterstützt Überspannungsschutz (ASRock Full Spike Pro-

tection)

• ELNA-Audiokondensatoren

LAN

• PCIE x1 Gigabit LAN 10/100/1000 Mb/s

• Realtek RTL8111E

• Unterstützt Wake-On-LAN

• Unterstützt Blitzschutz/Schutz gegen elektrostatische Entla-

dung (ASRock Full Spike Protection)

• Unterstützt LAN-Kabelerkennung

• Unterstützt energieezientes Ethernet 802.3az

• Unterstützt PXE

Rückblende,

E/A

• 1 x PS/2-Maus-/Tastaturanschluss

• 1 x D-Sub-Port

• 1 x DVI-D-Port

• 4 x USB 2.0-Ports (unterstützt Schutz gegen elektrostatische

Entladung (ASRock Full Spike Protection))

• 2 x USB 3.0-Ports (unterstützt Schutz gegen elektrostatische

Entladung (ASRock Full Spike Protection))

• 1 x RJ-45-LAN-Port mit LED (Aktivität/Verbindung-LED

und Geschwindigkeit-LED)

• HD-Audioanschlüsse: Line-in / Vorderer Lautsprecher /

Mikrofon

17

H110M-DVS/D3

Deutsch

Speicher

• 4 x SATA-III-6,0-Gb/s-Anschlüsse, unterstützt NCQ, AHCI

und Hot-Plugging

Anschluss

• 1 x COM-Anschluss-Stileiste

• 1 x TPM-Stileiste

• 1 x Gehäuseeingri- und Lautsprecher-Stileiste

• 1 x CPU-Lüeranschluss (4-polig)

(intelligente Lüergeschwindigkeitssteuerung)

• 1 x Gehäuselüeranschluss (4-polig)

(intelligente Lüergeschwindigkeitssteuerung)

• 1 x 24-poliger ATX-Netzanschluss

• 1 x 4-poliger 12-V-Netzanschluss

• 1 x Audioanschluss an Frontblende

• 1 x USB 2.0-Stileiste (unterstützt 2 USB 2.0-Ports) (unter-

stützt Schutz gegen elektrostatische Entladung (ASRock Full

Spike Protection))

• 1 x USB 3.0-Stileiste (unterstützt 2 USB 3.0-Ports) (unter-

stützt Schutz gegen elektrostatische Entladung (ASRock Full

Spike Protection))

BIOS-Funktion

• 128-Mb-AMI-UEFI-Legal-BIOS mit Unterstützung mehr-

sprachiger grascher Benutzerschnittstellen

• ACPI 1.1-konforme Aufweckereignisse

• SMBIOS 2.3.1-Unterstützung

• CPU, GT_CPU, DRAM, PCH 1,0V, VCCIO, VCCSA Mehr-

fachspannungsanpassung

Hardwareüber-

wachung

• CPU-/Gehäusetemperaturerkennung

• CPU-/Gehäuselüertachometer

• Lautloser CPU-/Gehäuselüer (automatische Anpassung der

Gehäuselüergeschwindigkeit durch CPU-Temperatur)

• CPU-/Gehäuselüer-Mehrfachgeschwindigkeitssteuerung

• Gehäuse-oen-Erkennung

• Spannungsüberwachung: +12 V, +5 V, +3,3 V, CPU Vcore,

CPU

18

Deutsch

Betriebssys-

tem

• Microso® Windows® 10, 64 Bit / 8.1, 64 Bit / 7, 32 Bit / 7, 64

Bit

* Zur Installation des Windows® 7-Betriebssystems wird ein

modiziertes Installationslaufwerk mit xHCI-Treibern in der

ISO-Datei benötigt. Detaillierte Anweisungen nden Sie auf Seite

62.

* Einzelheiten zum aktualisierten Windows® 10-Treiber

entnehmen Sie bitte der ASRock-Webseite:

http://www.asrock.com

Zerti-

zierungen

• FCC, CE, WHQL

• ErP/EuP ready (ErP/EuP ready-Netzteil erforderlich)

Bitte beachten Sie, dass mit einer Übertaktung, zu der die Anpassung von BIOS-Einstellungen,

die Anwendung der Untied Overclocking Technology oder die Nutzung von Übertaktung-

swerkzeugen von Drittanbietern zählen, bestimmte Risiken verbunden sind. Eine Übertaktung

kann sich auf die Stabilität Ihres Systems auswirken und sogar Komponenten und Geräte Ihres

Systems beschädigen. Sie sollte auf eigene Gefahr und eigene Kosten durchgeführt werden.

Wir übernehmen keine Verantwortung für mögliche Schäden, die durch eine Übertaktung

verursacht wurden.

* Detaillierte Produktinformationen nden Sie auf unserer Webseite: http://www.asrock.com

19

H110M-DVS/D3

Français

Spécications

Plateforme

• Facteur de forme Micro ATX

• Conception à condensateurs solides

• PCB en tissu de verre haute densité

Processeur

• Prend en charge les processeurs 6

e

génération Intel® Core

TM

i7/

i5/i3/Pentium®/Celeron® (Socket 1151)

• Prend en charge la technologie Intel® Turbo Boost 2.0

Chipset

• Intel® H110

Mémoire

• Technologie mémoire double canal DDR3/DDR3L

• 2 x fentes DIMM DDR3/DDR3L

• Prend en charge les mémoires sans tampon non ECC DDR3/

DDR3L 1600/1333/1066

• Capacité max. de la mémoire système : 32Go

• Prend en charge Intel® Extreme Memory Prole (XMP)1.3/1.2

Fente

d’expansion

• 1 x fente PCI Express 3.0 x 16 (PCIE1:mode x16)

• 2 x fentes PCI Express 2.0 x1

Graphiques

* La technologie Intel® HD Graphics Built-in Visuals et les sorties

VGA sont uniquement prises en charge par les processeurs

intégrant un contrôleur graphique.

• Prend en charge la technologie Intel® HD Graphics Built-in

Visuals : Intel® Quick Sync Video avec AVC, MVC (S3D) et

MPEG-2 Full HW Encode1, Intel® InTru

TM

3D, Intel® Clear

Video HD Technology, Intel® Insider

TM

, Intel® HD Graphics

510/530

• Pixel Shader 5.0, DirectX 12

• Mémoire partagée max. 1792Mo

• Double sortie graphique: Prend en charge les ports D-Sub et

DVI-D via contrôleurs d’achage indépendants

• Prend en charge le mode DVI-D avec une résolution maximale

de 1920x1200 @ 60Hz

• Prend en charge le mode D-Sub avec une résolution maximale

de 1920x1200 @ 60Hz

Страница загружается...

ASROCK H110M-DVS/D3 Руководство пользователя

Похожие модели бренда