Yamaha AX-596 Руководство пользователя

Бренд: Yamaha

Модель: AX-596

Категория: Аудиоусилители

Тип: Руководство пользователя

Yamaha AX-596 — мощный и многофункциональный стереоусилитель с выходной мощностью 100 Вт на канал при сопротивлении 8 Ом. Он обеспечивает высококачественный звук благодаря использованию высококачественных компонентов и тщательно продуманной конструкции.

Усилитель оснащен различными входами для подключения различных источников звука, включая проигрыватели компакт-дисков, DVD-плееры, тюнеры и магнитофоны. Также имеется выход для подключения эквалайзера или процессора объемного звучания.

Yamaha AX-596 имеет несколько режимов работы, таких как Pure Direct для воспроизведения чистого звука источника и CD/DVD Direct для воспроизведения чистого звука с компакт-дисков и DVD.

AX-596

STEREO AMPLIFIER

AMPLIFICATEUR STEREO

OWNER’S MANUAL

MODE D’EMPLOI

U C A

• Explanation of Graphical Symbols

The lightning flash with arrowhead

symbol, within an equilateral triangle,

is intended to alert you to the

presence of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert

you to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

SAFETY INSTRUCTIONS

1 Read Instructions – All the safety and operating

instructions should be read before the unit is operated.

2 Retain Instructions – The safety and operating

instructions should be retained for future reference.

3 Heed Warnings – All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and other

instructions should be followed.

5 Water and Moisture – The unit should not be used near

water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a

swimming pool, etc.

6 Carts and Stands – The unit should be used only with

a cart or stand that is recommended by the

manufacturer.

6A A unit and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause

the unit and cart combination to overturn.

7 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

8 Ventilation – The unit should be situated so that its

location or position does not interfere with its proper

ventilation. For example, the unit should not be

situated on a bed, sofa, rug, or similar surface, that

may block the ventilation openings; or placed in a built-

in installation, such as a bookcase or cabinet that may

impede the flow of air through the ventilation openings.

9 Heat – The unit should be situated away from heat

sources such as radiators, stoves, or other appliances

that produce heat.

10 Power Sources – The unit should be connected to a

power supply only of the type described in the

operating instructions or as marked on the unit.

11 Power-Cord Protection – Power-supply cords should

be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the

unit.

12 Cleaning – The unit should be cleaned only as

recommended by the manufacturer.

13 Nonuse Periods – The power cord of the unit should be

unplugged from the outlet when left unused for a long

period of time.

14 Object and Liquid Entry – Care should be taken so that

objects do not fall into and liquids are not spilled into

the inside of the unit.

15 Damage Requiring Service – The unit should be

serviced by qualified service personnel when:

A. The power-supply cord or the plug has been

damaged; or

B. Objects have fallen, or liquid has been spilled into

the unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or

exhibits a marked change in performance; or

E. The unit has been dropped, or the cabinet

damaged.

16 Servicing – The user should not attempt to service the

unit beyond those means described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

17 Power Lines – An outdoor antenna should be located

away from power lines.

18 Grounding or Polarization – Precautions should be

taken so that the grounding or polarization is not

defeated.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

IMPORTANT

Please record the serial number of this system in the

space below.

Model:

Serial No.:

The serial number is located on the rear of the main

unit.

Retain this Owner’s Manual in a safe place for future

reference.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

III

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most out

of your equipment by playing it at a safe level. One that lets

the sound come through loud and clear without annoying

blaring or distortion – and, most importantly, without

affecting your sensitive hearing.

Since hearing damage from loud sounds is

often undetectable until it is too late, YAMAHA

and the Electronic Industries Association’s

Consumer Electronics Group recommend you

to avoid prolonged exposure from excessive

volume levels.

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the

USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies

and, if not installed and used according to the

instructions found in the users manual, may cause

interference harmful to the operation of other

electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this

product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

UNPACKING After unpacking, check that the following items are contained.

DEBALLAGE Après le déballage, vérifier que les pièces suivantes sont incluses.

● Remote control

● Télécommande

● Batteries (size AA, R6, UM-3)

● Piles (format AA, R6, UM-3)

CD/DVD

TAPE

TUNERPHONO

AUX

–

A/B/C/D/E

DECK

A/B

DIR BDIR A

TAPE

DISC SKIP

STANDBY/ON

PRESET

+–

TUNER

VOLUME

Opening and closing the front cover

Close the front cover whenever the controls inside the panel are not used.

Ouverture et fermeture du couvercle avant

Fermer le couvercle avant lorsque les commandes placées à l’intérieur du panneau ne sont pas utilisées.

To open the front cover

Pour ouvrir le couvercle avant

To close the front cover

Pour fermer le couvercle avant

English

E-1

Thank you for selecting this YAMAHA stereo amplifier.

FEATURES

100W + 100W (8Ω) RMS Output Power, 0.015% THD, 20–20,000 Hz

Highly Dynamic Power, Low Impedance Drive Capability

Continuously Variable LOUDNESS Control

CD/DVD DIRECT AMP Switch Used to Reproduce the Purest CD and DVD Sound

PURE DIRECT Switch Used to Reproduce the Purest Source Sound

REC OUT Selector Independent of Input Source Selection

PRE OUT/MAIN IN Terminals for Connecting An Equalizer, Surround-Sound Processor, etc.

Remote Control Capability

CONTENTS

SAFETY INSTRUCTIONS ....................................................................................... II

UNPACKING ........................................................................................................... IV

FEATURES ............................................................................................................... 1

CAUTION ...................................................................................................................2

NOTES ABOUT THE REMOTE CONTROL.............................................................. 3

CONTROLS AND THEIR FUNCTIONS .................................................................... 4

CONNECTIONS........................................................................................................ 7

OPERATION ........................................................................................................... 10

TROUBLESHOOTING ............................................................................................ 13

SPECIFICATIONS................................................................................................... 14

E-2

1. To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2. Install this unit in a cool, dry, clean place – away from

windows, heat sources, sources of excessive vibration,

dust, moisture and cold. Avoid sources of humming

(transformers, motors). To prevent fire or electrical

shock, do not expose the unit to rain or water.

3. Never open the cabinet. If something drops into the

set, contact your dealer.

4. Do not use force on switches, controls or connection

wires. When moving the unit, first disconnect the

power plug and the wires connected to other

equipments. Never pull the wires themselves.

5. The openings on the unit cover assure proper

ventilation of the unit. If these openings are

obstructed, the temperature inside the unit will rise

rapidly; therefore, avoid placing objects against these

openings. Install the unit in a well-ventilated area to

prevent fire or damage.

<Europe, U.K. and China models only>

Be sure to allow a space of at least 20 cm behind, 20

cm on both sides and 30 cm above the top panel of the

unit to prevent fire or damage.

6. The voltage used must be the same as that specified

on this unit. Using this unit with a higher voltage than

specified is dangerous and may result in fire or other

accidents. YAMAHA will not be held responsible for

any damage resulting from use of this unit with a

voltage other than specified.

7. Always set the VOLUME control to “

∞

” before starting

the audio source play. Increase the volume gradually

to an appropriate level after the play has been started.

8. Do not attempt to clean the unit with chemical solvents

as this might damage the finish. Use a clean, dry

cloth.

9. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding

that the unit is faulty.

10. When not planning to use this unit for a long period

(ie., vacation, etc.), disconnect the AC power plug from

the wall outlet.

11.

To prevent lightning damage, disconnect the AC power

plug when there is an electric storm.

12. Grounding or polarization – Precautions should be

taken so that the grounding or polarization of an

appliance is not defeated.

13. Do not connect any audio equipment to the AC outlet

on the rear panel if the equipment requires more power

than the outlet is rated to provide.

14. VOLTAGE SELECTOR

(China and General models only)

The voltage selector on the rear panel of this unit

must be set for your local main voltage BEFORE

plugging into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

When this unit is turned off by pressing the STANDBY/ON

switch on the front panel or the remote control, the

STANDBY indicator on the front panel lights up. This state

is called the standby mode. In this mode, this unit is

designed to consume a small amount of power. This

unit’s power supply is completely cut off from the AC line

only when the POWER switch on the front panel is set in

the OFF position or the AC power cord is disconnected.

For Canadian Customers

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

WARNING

Do not change the IMPEDANCE SELECTOR switch

setting while the power to this unit is on, otherwise

this unit may be damaged.

If this unit fails to turn on when the POWER switch is

pressed:

The IMPEDANCE SELECTOR switch may not be set to

either end. If so, set the switch to either end when this

unit’s power supply is completely cut off.

CAUTION: Read this before operating your unit.

(U.S.A. model)

IMPEDANCE SELECTOR

CAUTION

SEE INSTRUCTION MANUAL FOR CORRECT SETTING.

IMPEDANCE SELECTOR

SET BEFORE POWER ON

A OR B : 6

Ω

MIN. /SPEAKER

A B : I2

Ω

MIN. /SPEAKER

A OR B : 4

Ω

MIN. /SPEAKER

A B : 8

Ω

MIN. /SPEAKER

SWITCHED

I20V 60Hz

l00W MAX. TOTAL

MAINS

R L

SPEAKERS

AC OUTLETS

English

E-3

30°

Remote control operation range

Notes

● The area between the remote control and the main unit

must be clear of large obstacles.

● Do not expose the remote control sensor to strong

lighting, in particular, an inverter type fluorescent lamp;

otherwise, the remote control may not work properly. If

necessary, position the main unit away from direct

lighting.

NOTES ABOUT THE REMOTE CONTROL

Battery installation

Since the remote control will be used for many of this unit’s

control operations, you should begin by installing the

supplied batteries.

1. Turn the remote control over and remove the battery

compartment cover by sliding it in the direction of the

arrow.

2. Insert the batteries (AA, R6, UM-3 type) according to the

polarity markings on the inside of the battery

compartment.

3. Close the battery compartment cover.

Battery replacement

If you notice that the remote control must be used closer to

the main unit, the batteries are weak. Replace both

batteries with new ones.

Notes

● Use AA, R6, UM-3 batteries.

● Be sure the polarities are correct. (See the illustration

inside the battery compartment.)

● Remove the batteries if the remote control is not used for

an extended period of time.

● If batteries leak, dispose of them immediately. Avoid

touching the leaked material and contact with clothing,

etc. Clean the battery compartment thoroughly before

installing new batteries.

Remote control

sensor

Within approximately

6 m (19.7 feet)

E-4

FRONT PANEL

CONTROLS AND THEIR FUNCTIONS

NATURAL SOUND STEREO AMPLIFIER

AX–596

VOLUME

–dB

PHONES

BASS

TREBLE

BALANCE

SPEAKERS

OFF

STANDBY/ON

POWER

OFF

STANDBY

INPUT

PURE DIRECT CD/DVD DIRECT AMP

AUX PHONOTUNERCD/DVDTAPEMD

LOUDNESS

FLAT

—30dB

REC OUT

CD/DVD

TUNER

PHONO

TAPE

AUX

456321

789

A B C DFE0

1 POWER

Press this switch inward (ON) to use this unit. In this

state, you can turn on this unit or turn this unit in the

standby mode by pressing STANDBY/ON. Press this

switch to release it outward (OFF) to completely cut off

this unit’s power supply from the AC line.

2 STANDBY indicator

Lights up only while this unit is in the standby mode.

3 STANDBY/ON

Press this switch to turn on the power. Press again to

set this unit in the standby mode.

* This switch can be used only when POWER is set in

the ON position.

Standby mode

This unit is still using a small amount of power in this

mode in order to be ready to receive infrared-signals

from the remote control.

4 Input source indicators

The indicator of the currently selected input source

lights up.

5 PURE DIRECT and indicator

Press this switch, and the indicator above it lights up.

You can listen to a source in the purest sound with this

function. (Refer to page 12 for details.)

Press this switch again to cancel this function.

6 CD/DVD DIRECT AMP and indicator

Press this switch, and the indicator above it lights up.

You can listen to a CD or DVD source in the purest

sound with this function. (Refer to page 12 for details.)

Press this switch again to cancel this function.

7 Remote control sensor

Receives signals from the remote control.

English

E-5

PHONES jack

When you listen with headphones, connect the

headphones to the PHONES jack and set both

SPEAKERS A and B switches to the OFF position.

9 SPEAKERS

Press the switch A or B (or both) inward (ON) for the

speakers you will use. Press and release the switch

outward (OFF) for the speakers you do not use.

0 Tone controls

BASS

Rotate this knob to increase or decrease the low

frequency response. The 0 position produces a flat

response.

TREBLE

Rotate this knob to increase or decrease the high

frequency response. The 0 position produces a flat

response.

A BALANCE

The balance of the output volume to the left and right

speakers can be adjusted to compensate for sound

imbalances caused by the speaker location or listening

room conditions.

B LOUDNESS

Used to compensate for the human ears’ loss of

sensitivity to high and low-frequency ranges at low

volume. (Refer to page 12 for details.)

C REC OUT selector

Rotate this knob to select the source for recording to

an MD recorder or tape deck. This setting is

independent of the INPUT selector setting, so this

function allows you to record the selected source while

listening to another source.

D Front cover

Refer to inside of the front cover on how to open and

close the front cover.

E INPUT selector

Turn this knob to select the input source.

The selected source will be shown by the lighting of

corresponding input source indicator.

F VOLUME

Turn this knob to raise or lower the volume level. (The

REC OUT level is not affected.)

PHONES

E-6

For Control of This Unit

1 STANDBY/ON

Press this key to turn on this unit or turn it into the

standby mode.

This key can be used only when the POWER switch on

the main unit is set in the ON position.

Standby mode

In this state, this unit consumes a very small

quantity of power to receive infrared-signals from

the remote control.

2 Input selector keys

Press a key to select the input source.

3 VOLUME +/–

Press these keys to increase or decrease the volume.

For Control of Other Components

Note

The functions of the keys to control other YAMAHA

components are the same as the corresponding keys on

those components. Refer to those components’

instruction manuals for details.

1 Tape deck keys

These keys control tape decks.

* DIR A, B and A/B apply only to double cassette tape

decks.

* Pressing DIR A will reverse the tape direction on a

single cassette tape deck with the automatic reverse

function.

2 CD player keys

These keys control compact disc players.

* DISC SKIP is used for disc changers only.

3 Tuner keys

These keys control tuners.

PRESET +: Press this key to select the next preset

station number.

PRESET –: Press this key to select the previous

preset station number.

A/B/C/D/E: Press this key to select the group (A – E)

of preset station numbers.

REMOTE CONTROL

The remote control is designed to control the most commonly used functions of the main unit. If you have a YAMAHA CD

player, tuner, tape deck, etc. with remote control compatibility, this remote control will also control their various functions.

CD/DVD

TAPE

TUNERPHONO

AUX

–

A/B/C/D/E

DECK

A/B

DIR BDIR A

TAPE

DISC SKIP

STANDBY/ON

PRESET

+–

TUNER

VOLUME

English

E-7

GND

PHONO

TUNER

(PLAY)

TAPE

OUT

(REC)

(PLAY)

OUT

(REC)

AUX

CAUTION

SEE INSTRUCTION MANUAL FOR CORRECT SETTING.

IMPEDANCE SELECTOR

SET BEFORE POWER ON

A OR B : 6

Ω

MIN. /SPEAKER

A B : I2

Ω

MIN. /SPEAKER

A OR B : 4

Ω

MIN. /SPEAKER

A B : 8

Ω

MIN. /SPEAKER

SWITCHED

I20V 60Hz

l00W MAX. TOTAL

MAINS

R L

CD/DVD

PRE

OUT

MAIN

AUDIO SIGNAL COUPLER SPEAKERS

AC OUTLETS

OUTPUT

GND

OUTPUT

AUDIO OUT

LINE OUT

LINE IN

AUDIO OUT

LINE OUT

LINE IN

CONNECTIONS

Caution: Plug in this unit and other components after all connections are completed.

● All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also refer to the owner’s

manual for each of your components.

● Use RCA type pin plug cables for audio/video units except speakers.

● The output (or input) terminals of YAMAHA audio/video units numbered 1, 2, 3, 4, etc. on the rear panel must be

connected to the same-numbered terminals of this unit.

Turntable

MD recorder, etc.

Tape deck, etc.

Left

Speakers A

Right

CD player or

DVD player

Tuner

Video cassette player,

etc.

Speakers B

Right Left

To AC outlet

(U.S.A. model)

: Indicates the direction of signals.

: Refer to page 9 for descriptions.

Note

These terminals are for connecting a turntable with an

MM or high output MC cartridge. If you have a turntable

with a low output MC cartridge, use an inline boosting

transformer or MC-head amplifier when connecting to

these terminals.

PHONO

(PLAY)

TAPE

OUT

(REC)

E-8

m Connecting speakers

Connect the SPEAKERS terminals to your speakers with

the wire with the proper gauge (keep it as short as

possible). If the connections are faulty, no sound will be

heard from the speakers. Make sure that the + and –

polarity markings of the speaker wires are observed and set

correctly. If these wires are reversed, the sound will be

unnatural and lack bass.

How to Connect:

SPEAKERS A terminals

Red: positive (+)

Black: negative (–)

1 Loosen the knob.

2 Insert the bare wire. [Remove approx.

10 mm (3/8”) insulation from the speaker wires.]

3 Tighten the knob and secure the wire.

● One or two speaker systems can be connected to this

unit. If you use only one speaker system, connect it to

either the SPEAKERS A or B terminals.

● Use speakers with the specified impedance shown on the

rear of this unit.

Caution

Do not let the bare speaker wires touch each other or

any metal part of this unit. This could damage this unit

or the speakers, or both.

SPEAKERS B terminals

Red: positive (+)

Black: negative (–)

1 Loosen the knob.

2 Insert the bare wire.

[Remove approx.

10 mm (3/8”)

insulation from the

speaker wires.]

3 Tighten the knob

and secure the wire.

<U.S.A., Canada, Australia, China and General

models only>

Banana Plug connections are also possible.

1 Tighten the terminal knob.

2 Simply insert the Banana Plug connector into the

terminal.

English

E-9

m Rear panel parts

GND terminal (For turntable use)

Connecting the ground wire of the turntable to the GND

terminal will normally minimize hum, but in some cases

better results may be obtained with the ground wire

disconnected.

PRE OUT/MAIN IN terminals

Removing the jumper pins from the PRE OUT/MAIN IN

terminals enables this unit to operate separately as a

control amplifier and a power amplifier. These terminals are

used for connecting a signal-processing system such as a

graphic equalizer or a surround-sound processor to this

unit.

If such an external unit is connected to these terminals, the

VOLUME control of this unit can be used for adjusting the

overall sound level.

To connect an external unit, first remove the jumper pins

from the PRE OUT/MAIN IN terminals, and then connect

the input terminals of that unit to the PRE OUT terminals

and its output terminals to the MAIN IN terminals. For

details, refer to the owner’s manual included with the unit to

be connected.

Notes

● When you do not use the PRE OUT/MAIN IN terminals,

never remove the jumper pins from these terminals. If

removed, no sound will be outputted from this unit.

● When you use this unit with an external unit connected to

the PRE OUT and MAIN IN terminals, make sure that the

CD/DVD DIRECT AMP switch and the PURE DIRECT

switch on the front panel are turned off.

● When you use this unit as a power amplifier, connect the

output terminals of an external control amplifier etc. to

this unit’s MAIN IN terminals. In this case, this unit’s

controls will not function except the PHONES jack and

the SPEAKERS switches. Use the controls on the

external control amplifier to make volume adjustment etc.

IMPEDANCE SELECTOR switch

WARNING

Do not change the IMPEDANCE SELECTOR switch

setting while the power to this unit is on, otherwise

this unit may be damaged.

If this unit fails to turn on when the POWER switch is

pressed:

The IMPEDANCE SELECTOR switch may not be set to

either end. If so, set the switch to either end when this

unit’s power supply is completely cut off.

Select the position whose

requirements your speaker

system meets.

(Left position)

If you use one pair of speakers, the impedance of

each speaker must be 4Ω or higher.

If you use two pairs of speakers, the impedance of

each speaker must be 8Ω or higher.

(Right position)

If you use one pair of speakers, the impedance of

each speaker must be 6Ω or higher.

If you use two pairs of speakers, the impedance of

each speaker must be 12Ω or higher.

AC OUTLET(S) (SWITCHED)

(U.S.A., Canada, Europe, China and General models)

...................................................... 3 SWITCHED OUTLETS

(U.K. and Australia models)............. 1 SWITCHED OUTLET

Use these to connect the power cords of your components

to this unit.

The power to the SWITCHED outlets is controlled by this

unit’s POWER or STANDBY/ON switch. These outlets will

supply power to any connected unit whenever this unit is

turned on.

The maximum power (total power consumption of

components) that can be connected to the SWITCHED AC

OUTLET(S) is 100W.

IMPEDANCE SELECTOR

SET BEFORE POWER ON

A OR B : 6

Ω

MIN. /SPEAKER

A B : I2

Ω

MIN. /SPEAKER

A OR B : 4

Ω

MIN. /SPEAKER

A B : 8

Ω

MIN. /SPEAKER

GND

PHONO

TUNER

(PLAY)

TAPE

OUT

(REC)

(PLAY)

OUT

(REC)

AUX

CD/DVD

PRE

OUT

MAIN

AUDIO SIGNAL

COUPLER

E-10

VOLUME

–dB

PHONES

BASS

TREBLE

BALANCE

SPEAKERS

OFF

STANDBY/ON

POWER

OFF

STANDBY

INPUT

CD/DVD DIRECT AMP

AUX PHONOTUNERCD/DVDTAPEMD

LOUDNESS

FLAT

—30dB

REC OUT

CD/DVD

TUNER

PHONO

TAPE

AUX

PURE DIRECT

Press POWER inward (ON).

3 If the STANDBY indicator is illuminated, press

STANDBY/ON to turn on the power. (The STANDBY

indicator turns off.)

4 Select the desired input source.

The indicator of the selected source lights up.

5 Select speakers A or B.

* Both speakers A and B can be selected.

* Be sure that the IMPEDANCE SELECTOR switch is

correctly set as explained on page 9.

* If you listen with headphones, press both switches to

release them outward (OFF).

6 Play the source.

Adjust the output level.

8 Adjust the tonal quality by using the BASS,

TREBLE, BALANCE, LOUDNESS controls, the

CD/DVD DIRECT AMP switch or the PURE

DIRECT switch. (Refer to page 12).

When you finish using this unit

Press STANDBY/ON again to set this unit in the standby

mode. (The STANDBY indicator lights up.)

To completely cut off this unit’s power

supply from the AC line

Press POWER to release it outward (OFF).

OPERATION

m Playing a source

–dB

POWER

OFF

STANDBY

STANDBY/ON

–

CD/DVD

TAPE

TUNERPHONO

AUX

–

STANDBY/ON

AUX PHONOTUNERCD/DVDTAPEMD

SPEAKERS

OFF

–

VOLUME

–dB

85 4

1, 7

STANDBY

Turns off.

POWER

STANDBY

Set to the “

∞

” position.

English

E-11

1 Follow the steps 1–3 of “Playing a source” on page

10.

2 Select the source you want to record.

3 Play the source.

4 Select the source with the INPUT selector and

adjust VOLUME to check the sound output.

m Recording a source to tape (or MD)

5 Begin recording on the tape deck (or MD recorder).

6 The sound of the recording can be monitored by

selecting the tape deck (or MD recorder) with the

INPUT selector.

7 Listening to another source by selecting it with the

INPUT selector will not affect the recording.

Notes

● The VOLUME, BASS, TREBLE, BALANCE, LOUDNESS

controls, the CD/DVD DIRECT AMP switch and the

PURE DIRECT switch have no effect on the material

being recorded.

● Please check the copyright laws in your country to record

from records, compact discs, radio, etc. Recording of

VOLUME

–dB

PHONES

BASS

TREBLE

BALANCE

SPEAKERS

OFF

STANDBY/ON

POWER

OFF

STANDBY

INPUT

CD/DVD DIRECT AMP

AUX PHONOTUNERCD/DVDTAPEMD

LOUDNESS

FLAT

—30dB

REC OUT

CD/DVD

TUNER

PHONO

TAPE

AUX

PURE DIRECT

REC OUT

CD/DVD

TUNER

PHONO

TAPE

AUX

–

CD/DVD

TAPE

TUNERPHONO

AUX

–dB

–

VOLUME

4, 6, 7

–

CD/DVD

TAPE

TUNERPHONO

AUX

E-12

Adjusting the BALANCE control

Adjust the balance of the output volume to the left and right

speakers to compensate for sound imbalance caused by

speaker location or listening room conditions.

Using the CD/DVD DIRECT AMP switch

You can enjoy the purest possible sound from your CD or

DVD player by pressing this switch. The indicator above it

lights up. With this function on, input signals from the CD or

DVD player are sent directly to the built-in special amplifier

for CD/DVD bypassing the INPUT selector, the BASS,

TREBLE, BALANCE, LOUDNESS controls and the PRE

OUT/MAIN IN terminals, and then sent to the power

amplifier. This signal routing reproduces the purest sound

eliminating any alterations to the CD or DVD signals.

Using the PURE DIRECT switch

You can enjoy the purest possible sound from your audio

sources by pressing this switch. The indicator above this

switch lights up. With this function on, the audio signals

bypass the BASS, TREBLE, BALANCE, LOUDNESS

controls and the PRE OUT/MAIN IN terminals, thus

eliminating any alterations to the audio signals.

Notes

● If both the CD/DVD DIRECT AMP and PURE DIRECT

switches are on, only the CD/DVD DIRECT AMP switch

will function.

● If this unit is turned off, sound may be distorted when

listening to a source with headphones that are connected

to an externally connected unit such as the CD player,

tape deck, etc.

● If any of the external units connected to this unit is turned

off, sound may be distorted when playing a source on

another unit that is also connected to this unit.

Adjusting the BASS and TREBLE controls

BASS: Turn this knob clockwise to increase (or counter-

clockwise to decrease) the low frequency

response.

TREBLE: Turn this knob clockwise to increase (or counter

clockwise to decrease) the high frequency

response.

Adjusting the continuously variable

LOUDNESS control

This control compensates for the human ears’ loss of

sensitivity to high and low-frequency ranges at low volume.

This control is adjustable to retain full tonal range at any

volume level.

Set to the “FLAT” position.

Set to the loudest listening level

that you would listen to.

Turn until the desired volume is

obtained.

WARNING

If the CD/DVD DIRECT AMP switch or PURE DIRECT

switch is pressed to turn it on with the LOUDNESS

control set at a certain level, the sound will suddenly

increase and may damage your ears or the speakers.

(The LOUDNESS control function may be bypassed.)

For this reason, be sure to press the CD/DVD DIRECT

AMP switch or PURE DIRECT switch after lowering the

volume or after checking that the LOUDNESS control is

properly set.

m Sound control

BALANCE

BASS

TREBLE

CD/DVD DIRECT AMP

PURE DIRECT

LOUDNESS

FLAT

—30dB

–dB

LOUDNESS

FLAT

—30dB

English

E-13

Problem

The unit cannot be turned on or

turns off suddenly soon after the

power is turned on.

This unit does not work normally.

No sound.

The sound suddenly goes off.

Only one of the speakers

produces the sound.

There is a lack of bass and no

ambience.

Sound “hums”.

The volume level is low while

playing a record.

The volume level cannot be

increased, or sound is distorted.

The sound is degraded when

listening with the headphones

connected to the compact disc

player or tape deck that are

connected with this unit.

Sound level is low.

The input source cannot be

changed, though the INPUT

selector is turned.

Using the BASS, TREBLE,

BALANCE and LOUDNESS

controls does not affect the tone.

The remote control does not

work.

The remote control does not

function properly.

What to Do

Firmly plug in the power cord.

Set the switch to either end when this

unit is off.

Turn off this unit by pressing the

POWER switch. After about 30 seconds

have passed, turn on this unit and

operate this unit again.

Connect the cords properly. If the

problem persists, the cords may be

defective.

Select an appropriate input source with

the INPUT selector.

Set the corresponding SPEAKERS

switch to the ON position.

Secure the connections.

Turn off this unit by pressing the

POWER switch, and then turn this unit

on to reset the protection circuit.

Adjust it to the appropriate position.

Connect the cords properly. If the

problem persists, the cords may be

defective.

Connect the speaker wires in the

correct phase (+ and –).

Firmly connect the audio plugs. If the

problem persists, the cords may be

defective.

Make the GND connection between the

turntable and this unit.

The turntable should be connected to

this unit through the MC head amplifier.

Turn on the power to the component.

Turn on the power to this unit.

Set the LOUDNESS control to the FLAT

position.

Switch off the CD/DVD DIRECT AMP

switch.

The CD/DVD DIRECT AMP switch or

PURE DIRECT switch must be

switched OFF to use those controls.

Replace the batteries with new ones.

The remote control will function from a

maximum range of 6 meters and no

more than 30 degrees off-axis from the

front panel.

Reposition of the main unit.

Cause

Power cord is not plugged in nor

completely inserted.

The IMPEDANCE SELECTOR switch on

the rear panel is not set to either end.

There is an influence of strong external

noise (lightning, excessive static

electricity, etc.) or a misoperation on this

unit while using this unit.

Incorrect output cord connections.

Appropriate input source is not selected.

The SPEAKERS switches are not set

properly.

Speaker connections are not secure.

The protection circuit has been activated

because of short circuit etc.

Incorrect setting of the BALANCE

control.

Incorrect cord connections.

The + and – wires are connected in

reverse at the amplifier or speakers.

Incorrect cord connections.

No connection from the turntable to the

GND terminal.

The record is being played on a

turntable with an MC cartridge.

The component connected to the TAPE

OUT or MD OUT terminals of this unit is

turned off.

This unit is turned off or in the standby

mode.

The LOUDNESS control is functioning.

The CD/DVD DIRECT AMP switch is

ON.

The CD/DVD DIRECT AMP switch or

PURE DIRECT switch is ON.

The batteries of this remote control are

weak.

Wrong distance or angle.

Direct sunlight or lighting (of an inverter

type fluorescent lamp etc.) is striking the

remote control sensor of the main unit.

TROUBLESHOOTING

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if

the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service

center.

E-14

SPECIFICATIONS

Power Section

Minimum RMS Output Power

8Ω, 20 Hz to 20 kHz, 0.015% THD ................100W+100W

Maximum Output Power (EIAJ)

(1 kHz, 10% THD)

8/6Ω........................................................................ 145/170W

Dynamic Power (IHF)

8/6/4/2Ω............................................... 140/170/220/290W

DIN Standard Output Power

(4Ω, 1 kHz, 0.7% THD)................................................ 155W

IEC Output Power (8Ω, 1 kHz, 0.015% THD).............. 110W

Power Band Width

8Ω, 50W, 0.03% THD ............................... 10 Hz to 50 kHz

Damping Factor

8Ω, 20 Hz to 20 kHz .....................................................320

Frequency Response .................... 20 Hz to 20 kHz50.5 dB

20 Hz to 100 kHz +0.5, –3 dB

Total Harmonic Distortion (20 Hz to 20 kHz)

CD/DVD to SP OUT (8Ω, 50W) ..............................0.008%

Signal-to-Noise Ratio (IHF-A Network)

CD/DVD (Input Shorted, CD/DVD DIRECT AMP: ON)

............................................................................... 110 dB

PHONO (MM)

(Input Shorted) ........................................................ 92 dB

Residual Noise (IHF-A Network)

CD/DVD DIRECT AMP: ON..................................... 35 µV

Control Section

Input Sensitivity/Impedance

CD/DVD, etc. ...............................................150 mV/47 kΩ

PHONO (MM) ...............................................2.5 mV/47 kΩ

Output Level

PRE OUT............................................................1V/1.2 kΩ

REC OUT ...................................................150 mV/0.6 kΩ

Headphone Output.............................................0.33V/680Ω

Channel Separation (1 kHz/10 kHz)

CD/DVD (Input 5.1 kΩ Terminated) ................ 65 dB/50 dB

Tone Control Characteristics

BASS ........................................................ 510 dB (20 Hz)

TREBLE.................................................. 510 dB (20 kHz)

Continuous LOUDNESS Control

Attenuation ................................................ –30 dB (1 kHz)

General

Power Supply

[U.S.A. and Canada models] .................... AC 120V, 60 Hz

[Europe and U.K. models]......................... AC 230V, 50 Hz

[Australia model] ....................................... AC 240V, 50 Hz

[China and General models]

........................................ AC 110/120/220/240V, 60/50 Hz

Power Consumption ...................................... Approx. 220W

AC Outlets

3 SWITCHED OUTLETS

[U.S.A., Canada, Europe, China and General models]

............................................................... 100W max. total

1 SWITCHED OUTLET

[U.K. and Australia models].................... 100W max. total

Dimensions (W x H x D)....................... 435 x 151 x 396 mm

(17-1/8” x 5-15/16” x 15-9/16”)

Weight ................................................ 10.6 kg (23 lbs. 5 oz.)

Accessories.................................................. Remote control

Batteries

Specifications subject to change without notice.

-1

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

V576270-1

Printed in Malaysia

Yamaha AX-596 Руководство пользователя

Бренд: Yamaha

Модель: AX-596

Категория: Аудиоусилители

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha AX-596 User manual
français: Yamaha AX-596 Manuel utilisateur
italiano: Yamaha AX-596 Manuale utente
español: Yamaha AX-596 Manual de usuario
Deutsch: Yamaha AX-596 Benutzerhandbuch
Nederlands: Yamaha AX-596 Handleiding
português: Yamaha AX-596 Manual do usuário
dansk: Yamaha AX-596 Brugermanual
polski: Yamaha AX-596 Instrukcja obsługi
čeština: Yamaha AX-596 Uživatelský manuál
svenska: Yamaha AX-596 Användarmanual
Türkçe: Yamaha AX-596 Kullanım kılavuzu
suomi: Yamaha AX-596 Ohjekirja
română: Yamaha AX-596 Manual de utilizare

Yamaha AX-596 Руководство пользователя

Yamaha AX-596 Руководство пользователя

на других языках

Похожие модели бренда