Yamaha XMV8140 Инструкция по применению

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

Manuale di istruzioni

Руководство пользователя

EnglishDeutschFrançaisEspañolItalianoРусский

POWER AMPLIFIER

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

The above warning is located on the top of the unit.

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to per-

sons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and mainte-

nance (servicing) instructions in the literature

accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radia-

tors, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The

wide blade or the third prong are provided for your

safety. If the provided plug does not fit into your out-

let, consult an electrician for replacement of the

obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience recepta-

cles, and the point where they exit from the appara-

tus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table speci-

fied by the manufacturer, or

sold with the apparatus. When

a cart is used, use caution

when moving the cart/appara-

tus combination to avoid injury

from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Ser-

vicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate nor-

mally, or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det

brugte batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä

käytetty paristo valmistajan ohjeiden mukaisesti.

(lithium caution)

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifi-

cations not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could

void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these require-

ments provides a reasonable level of assurance that your

use of this product in a residential environment will not result

in harmful interference with other electronic devices. This

equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the opera-

tion of other electronic devices. Compliance with FCC regu-

lations does not guarantee that interference will not occur in

all installations. If this product is found to be the source of

interference, which can be determined by turning the unit

“

OFF

” and “ON”, please try to eliminate the problem by using

one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distrib-

ute this type of product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of America,

Electronic Service Division, 6600 Orangethorpe Ave, Buena

Park, CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park,

Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Power Amplifier

Model Name : XMV4280/XMV4140/XMV4280-D/

XMV4140-D

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including

interference that may cause undesired operation.

See user manual instructions if interference to radio reception

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(FCC DoC)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED IMPOR-

TANT. The wires in this mains lead are coloured in accordance

with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be

connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol or colored GREEN or

GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

(3 wires)

In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

(class I hokuo)

This product contains a battery that contains perchlorate material.

Perchlorate Material—special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Perchlorate)

이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으

로 하며, 모든 지역에서 사용할 수 있습니다.

(class b korea)

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited

to, the following:

• Do not place the power cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy

objects on it, or place it in a position where anyone could walk on, trip over,

or roll anything over it.

• Only use the voltage specified as correct for the device. The required voltage

is printed on the name plate of the device.

• Use only the supplied power cord/plug.

If you intend to use the device in an area other than in the one you

purchased, the included power cord may not be compatible. Please check

with your Yamaha dealer.

• Check the electric plug periodically and remove any dirt or dust which may

have accumulated on it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock, damage to

the device(s), or even fire.

• This device contains no user-serviceable parts. Do not open the device or

attempt to disassemble the internal parts or modify them in any way. If it

should appear to be malfunctioning, discontinue use immediately and have

it inspected by qualified Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet

conditions, or place on it any containers (such as vases, bottles or glasses)

containing liquids which might spill into any openings. If any liquid such as

water seeps into the device, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the device inspected by qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may

fall over and cause a fire.

• When one of the following problems occur, immediately turn off the power

switch and disconnect the electric plug from the outlet. Then have the device

inspected by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of the device.

• If this device should be dropped or damaged, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the device

inspected by qualified Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or

damage to the device or other property. These precautions include, but are not limited to, the following:

• When removing the electric plug from the device or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the device is not to be used

for extended periods of time, or during electrical storms.

• Do not place the device in an unstable position where it might accidentally

fall over.

• Do not block the vents. This device has ventilation holes at the front/rear/

sides to prevent the internal temperature from becoming too high. In

particular, do not place the device on its side or upside down. Inadequate

ventilation can result in overheating, possibly causing damage to the

device(s), or even fire.

• Do not use the device in a confined, poorly-ventilated location. If this device

is to be used in a small space other than an EIA-standard rack, make sure

that there is adequate space between the device and surrounding walls or

other devices: at least 10 cm at the sides, 10 cm behind and 40 cm above.

Inadequate ventilation can result in overheating, possibly causing damage to

the device(s), or even fire.

• Do not place the device in a location where it may come into contact with

corrosive gases or salt air. Doing so may result in malfunction.

• Keep device away from the reach of children.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn

off the power switch and disconnect the plug from the outlet. Even when the

power switch is turned off, electricity is still flowing to the product at the

minimum level. When you are not using the product for a long time, make

sure to unplug the power cord from the wall AC outlet.

• If the device is mounted in an EIA standard rack, carefully read the section

“Precautions for Rack Mounting” on page 8. Inadequate ventilation can

result in overheating, possibly causing damage to the device(s),

malfunction, or even fire.

• Before connecting the device to other devices, turn off the power for all

devices. Before turning the power on or off for all devices, set all volume

levels to minimum.

• Use only speaker cables for connecting speakers to the speaker connectors.

Use of other types of cables may result in fire.

Power supply/power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/power cord

Location

Connections

PA_en_1 1/2

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

• Remove the power plug from the AC outlet when cleaning the device.

• Do not insert your fingers or hands in any gaps or openings on the device

(vents).

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into

any gaps or openings on the device (vents) If this happens, turn off the

power immediately and unplug the power cord from the AC outlet. Then

have the device inspected by qualified Yamaha service personnel.

• Do not rest your weight on the device or place heavy objects on it, and avoid

use excessive force on the buttons, switches or connectors.

• Do not use speakers for a long period of time at a high or uncomfortable

volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

• This device has a built-in backup battery. When you unplug the power cord

from the AC outlet, the internal data is retained. However, if the backup

battery fully discharges, this data will be lost. When the backup battery is

running low, the display indicates “012.” and the ALERT indicator is

flashing. In this case, immediately save the data to external device such as a

computer, then have qualified Yamaha service personnel replace the backup

battery.

Always turn the power off when the device is not in use.

NOTICE

To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.

 Handling and maintenance

• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the device,

TV, or radio may generate noise.

• Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car

during the day), in order to prevent the possibility of panel disfiguration, unstable operation, or damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel.

• When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents, cleaning fluids, or chemical-impregnated wip-

ing cloths.

• Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved from one

location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause dam-

age. If there is reason to believe that condensation might have o

ccurr

ed, leave the device for several hours without turning on the

power until the condensation has completely dried out.

• Do not use this device for any purpose other than driving loudspeakers.

• When turning on the AC power in your audio system, always turn on tthe device LAST, to avoid speaker damage. When turning the

power off, the device should be turned off FIRST for the same reason.

 Saving data

This device has a built-in backup battery that maintains data in internal memory even when the device’s power is switched off. The

backup battery will eventually become depleted, however, and when that happens the contents of the internal memory will be lost.*

To prevent loss of data be sure to replace the backup battery before it becomes fully depleted. When the remaining capacity of the

backup battery becomes so low that it needs to be replaced a “012.” message will appear on the display during operation or when the

device is powered on. If either of these messages appears do not turn off the power and immediately transfer any data you want to save

to a computer or other external storage device, then have qualif

ied Yamaha service

personnel replace the backup battery. The average

life of the internal backup battery is approximately 5 years, depending on operating conditions.

* Data items maintained in the internal memory by the backup battery are as follows:

•Device parameters (Attenuator values, Polarity settings, HPF settings, Analog/digital input setting, and [SIGNAL] indicator display

setting).

•Event log.

Data items other than those described above are stored in memory that does not require backup power, and will be retained even if the

backup battery fails.

Information

 About this manual

• The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your

device.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Maintenance

Handling caution

Backup battery

Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.

European Models

Inrush Current based on EN 55103-1:2009

10A (on initial switch-on)

5A (after a supply interruption of 5s)

Conforms to Environments: E1, E2, E3 and E4

PA_en_1 2/2

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Contents

Introduction.....................................................................................................................7

Features.................................................................................................................................. 7

Included items......................................................................................................................... 7

Related Manuals and Software............................................................................................... 7

Firmware Updates................................................................................................................... 8

About Dante ............................................................................................................................ 8

Precautions for Rack Mounting ............................................................................................... 8

Controls and Functions .................................................................................................9

Front Panel.............................................................................................................................. 9

Rear Panel ............................................................................................................................ 12

Connections and Setting Up .......................................................................................16

Setup for Analog Signal Input ............................................................................................... 16

[REMOTE] and [FAULT OUTPUT] Connectors ..................................................................... 21

Operations.....................................................................................................................23

Front Panel Operations ......................................................................................................... 23

Initializing the Internal Memory............................................................................................. 25

Appendix .......................................................................................................................26

Troubleshooting..................................................................................................................... 26

Alert Numbers and Content .................................................................................................. 27

Dante Messages (XMV4280-D/XMV4140-D only)................................................................ 29

High-impedance and Low-impedance Connections ............................................................. 30

BTL (Balanced Transformer Less) Connection..................................................................... 31

Specifications .............................................................................................................234

General Specifications........................................................................................................ 234

Block Diagram..................................................................................................................... 236

Dimensions ......................................................................................................................... 236

Current Draw and Heat Dissipation .................................................................................... 237

* The contents of this manual apply to the latest specifications as of the printing date. Since Yamaha makes continuous

improvements to the product, this manual may not apply to the specifications of your particular product. To obtain the lat-

est manual, access the Yamaha website then download the manual file. Since specifications, equipment or separately

sold accessories may not be the same in every locale, please check with your Yamaha dealer.

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Introduction

Thank you for your purchase of the Yamaha XMV4280, XMV4140, XMV4280-D or XMV4140-D power

amplifier. Please read through this manual carefully before beginning use, so that you will be able to take full

advantage of your power amplifier’s superlative features and enjoy trouble-free operation for years to come.

After you have read the manual, keep it in a safe place for reference when needed.

The XMV is a multi-channel power amplifier with the follow-

ing features.

• Both high-impedance and low-impedance connec-

tions are supported

Both high-impedance connections to 70V/100V lines and

4Ω/8Ω low-impedance connections are supported. A rear

panel DIP switch allows this setting to be specified for every

two channels.

• Newly-developed “Double Power mode”

The newly-developed “Double Power mode” doubles the

amplifier output of each channel when low-impedance con-

nections are used.

* The number of available channels will be halved.

•Settings can be made via application software

Although settings such as mute on/off and attenuator values

can be edited from the panel of the amplifier itself, you can

use an MTX series matrix processor and computer to edit the

settings of multiple XMV units.

• Support for the newly-developed “YDIF” digital

audio transmission format

(XMV4280/XMV4140 only)

This allows up to 16 channels of audio and word clock to be

transmitted and received via an Ethernet cable.

This model can receive four channels of audio signals via

YDIF.

• Dante network for large-scale systems

(XMV4280-D/XMV4140-D only)

This enables audio signal transfer over long-distance with

Dante equipped devices (such as the MTX5-D) with stan-

dard Ethernet cables.

•High efficiency

The newly-developed output circuits allows high efficiency.

• Redundancy between the digital and analog inputs

When the pilot tone of a digital input is interrupted or an

analog input reaches the specified level or higher, the input

switches from digital to analog.

*This function can be set from the Amp Editor.

• Owner’s Manual

•Power cord

• Euroblock plugs (3-pin, 3.50mm pitch) x 2

• Euroblock plugs with tabs (3-pin, 5.08mm pitch) x 4

• Cable ties x 4

Use the MTX-MRX Editor for building a system in which the

MTX/MRX and XMV are combined. Use the Amp Editor for a

system consisting only of the XMV(s). Related manuals, of the

MTX-MRX Editor or Amp Editor (heretofore collectively

referred to as “the editor”) can be downloaded from the down-

load page of the following website.

http://www.yamahaproaudio.com/

• List of related manuals

The “MTX-MRX Editor User Guide,” “MTX Setup Manual,”

“MRX Setup Manual,” and “Amp Editor Owner’s Manual” are

electronic files in PDF format.

You can read the books on a computer. Use Adobe® Reader®

to read the books on screen, search for words very quickly, print

specific pages, or click links to display sections of special inter-

est. The ability to search for words, or to follow links directly to

relevant sections in the document, are helpful attributes of this

electronic file format. We encourage you to take advantage of

these benefits.

You can download the latest Adobe Reader application from the

website listed below.

http://www.adobe.com/

NOTE

• When there are differences in the specifications of the XMV4280/XMV4280-D and the XMV4140/XMV4140-D, this manual will

use curly brackets { } to enclose information that applies only to the XMV4140/XMV4140-D.

(Example: 280W {140W}).

• Unless otherwise specified, illustrations are taken from the XMV4280/XMV4280-D.

• For the remainder of this manual, the XMV4280, XMV4140, XMV4280-D and XMV4140-D are referred to as “XMV” collectively.

•In this book, the matrix processor MTX series units are reffered to as “MTX” collectively.

Features Included items (please check)

Related Manuals and Software

MTX or MRX

owner’s manual

This explains how to use the proces-

sor (MTX or MRX).

MTX-MRX Editor

User Guide

This explains how to use MTX-MRX

Editor.

MTX Setup Manual

MRX Setup Manual

This explains how to use and set up

the matrix processor MTX and MRX

series that is used along with the

XMV power amp.

Amp Editor

Owner’s Manual

This explains how to use Amp Editor.

Introduction

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Use the MTX-MRX Editor or the Amp Editor to update the

firmware of the XMV or check the firmware version. For opera-

tion details, refer to the related manuals.

You can download the latest firmware from the “Downloads”

page on the following website.

http://www.yamahaproaudio.com/

The XMV4280-D/XMV4140-D units feature Dante technology

as a protocol to transmit audio signals. Dante is a network pro-

tocol developed by Audinate. It is designed to deliver multi-

channel audio signals at various sampling and bit rates, as well

as device control signals over a Giga-bit Ethernet (GbE) net-

work. Dante also offers the following benefits:

• It transmits up to 512 in/512 out, for a total 1024 channels

(theoretically) of audio over a GbE network.

(The XMV4280-D/XMV4140-D features four inputs with a

24/32-bit resolution.)

• Dante-enabled devices will automatically configure their

network interfaces and find each other on the network. You

can label Dante devices and their audio channels with names

that make sense to you.

• Dante uses high accuracy network synchronization standards

to achieve sample-accurate playback with extremely low

latency and jitter.

(Four types of latency are available on the XMV4280-D/

XMV4140-D: 0.25 msec, 0.5 msec, 1.0 msec, and 5.0 msec.)

• Dante supports redundant connections via primary and sec-

ondary circuits to defend against unforeseen difficulties.

• Connecting a Dante-enabled device to a computer over

Ethernet enables you to directly input or output audio signals

without using any audio interface devices.

Visit Audinate website for more details on Dante.

http://www.audinate.com/

More information on Dante is also posted on the Yamaha Pro

Audio website:

http://www.yamahaproaudio.com/

Firmware Updates

About Dante

NOTE

Please do not use the EEE function (*) of network switches in a

Dante network.

Although power management should be negotiated automati-

cally in switches that support EEE, some switches do not per-

form the negotiation properly.

This may cause EEE to be enabled in Dante networks when it

is not appropriate, resulting in poor synchronization perfor-

mance and occasional dropouts.

Therefore we strongly recommend that:

- If you use managed switches, ensure that they allow EEE to

be disabled. Make sure that EEE is disabled on all ports

used for real-time Dante traffic.

- If you use unmanaged switches, make sure to not use net-

work switches that support the EEE function, since EEE

operation cannot be disabled in these switches.

* EEE (Energy Efficient Ethernet) is a technology that reduces switch

power consumption during periods of low network traffic. It is also

known as Green Ethernet and IEEE802.3az.

Precautions for Rack Mounting

This unit is rated for operation at ambient temperatures

ranging from 0 to 40 degrees Celsius. When mounting

the unit with other XMV unit(s) or other device(s) in an

EIA standard equipment rack, internal temperatures can

exceed the specified upper limit, resulting in impaired

performance or failure. When rack mounting the unit,

always observe the following requirements to avoid heat

buildup:

• When mounting the unit in a rack with devices such as

power amplifiers that generate a significant amount of

heat, leave more than 1U of space between the XMV

and other equipment. Also either leave the open

spaces uncovered or install appropriate ventilating pan-

els to minimize the possibility of heat buildup.

• To ensure sufficient airflow, le

ave the

rear of the rack

open and position it at least 10 centimeters from walls

or other surfaces. If the rear of the rack can’t be left

open, install a commercially available fan or similar

ventilating option to secure sufficient airflow. If you’ve

installed a fan kit, there may be cases in which closing

the rear of the rack will produce a greater cooling effect.

Refer to the rack and/or fan unit manual for details.

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Controls and Functions

XMV4280/XMV4140

XMV4280-D/XMV4140-D

q Power switch

Turns power to the unit ON or OFF. Setting the switch to the

upward position turns the power on; the [POWER] indicator

!0 will light green. Setting the switch to the downward posi-

tion turns the power off. If the switch is in the upward posi-

tion and the [POWER] indicator is flashing, the unit is in

standby mode.

w [PROTECTION] A/B/C/D indicators

When the protection system is active, the indicator will light

orange. If the audio output is muted, turn off the power and

wait for the XMV to cool before turning the power on again.

The protection circuit will operate and the [PROTECTION]

indicator will light in the following situations.



If the amplifier overheats and the output lim-

iter operates

The speaker output will be attenuated if the heat sink of

the amplifier section exceeds 80°C, and will be muted if

the heat sink exceeds 90°C. The [PROTECTION] indica-

tor will light at 80°C or higher.



If the power supply overheats and shuts-down

The fan will rotate at high speed if the power supply sec-

tion exceeds 90°C, and the analog circuits will shut down

if it exceeds 100°C.

The [PROTECTION] indicator will light at 100°C or

higher.

Front Panel

q wer!8 !8 !0

i t u !7o

!1 !2 !3

q wer!8 !8 !0

i t u !7o

!4!5

CAUTION

• To ensure that high-volume noise is not output from

the speakers, power-on the equipment starting with

the audio sources, then the mixer and processors

(such as the MTX), and finally the amplifiers. Reverse

this order when turning the system off.

• Rapidly turning the power switch ON and OFF in suc-

cession can cause the unit to malfunction. After turn-

ing the power switch OFF, wait for about 5 seconds

before turning it ON again.

• If you modified parameter settings, do not turn the

power switch OFF for at least one second. Otherwise,

the changes to the settings may be lost.

• Even when the power switch is turned off, a small

amount of current is flowing through the unit. If you

plan not to use the unit for a long period of time,

remove the power cable from the AC outlet.

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 When overcurrent is detected

If for any reason the impedance falls below the specifica-

tion for the mode, the speaker output is muted to prevent

overcurrent; muting will be cancelled after approximately

one second. If overcurrent is detected after muting is can-

celled, the output will be muted again.



If DC output is detected

The power supply section will be shut down.

 If excessive total current or maximum current

is detected

The output signal will be lowered.

e [LIMIT] A/B/C/D indicators

When the limiter operates, the speaker output will be limited

and the indicator will light red. Lower the attenuator value so

that the limiter does not activate, referring to “Changing the

attenuator setting” (page 20). The limiter will operate in the

following situations.

• When an instantaneous input overload is detected

• When an input overload has been occurring for a specific

duration

• When the heat sink of the amplifier section exceeds the

allowable temperature

r [SIGNAL] A/B/C/D indicators

The [SIGNAL] indicator will light in green when the input/

output signal level exceeds a certain level.

*1 For details on switching the indicator between input and

output, refer to “Front Panel Operations” (page 23).

*2 Depends on the condition. Refer to “[SIGNAL] Indicator Lit

Level” (page 235).

t [SELECT] A/B/C/D buttons/indicators

Use these buttons to select the output channel that you want

to control. The indicator of the selected channel will light in

green.

By using these in conjunction with the [FUNCTION] button

!7, you can change the parameter that is controlled by the

encoder. Refer to “Front Panel Operations” (page 23).

When the [PANEL LOCK] indicator !6 is lit, front panel

operations are locked, and output channel operations are not

possible. Defeat the lock if you want to perform these opera-

tions.

y Display

This is a 3-digit 7-segment display that shows information

such as the attenuator value of the channel selected by the

[SELECT] button t or the alert number (page 27).

u Encoder

This encoder is used to edit parameters. For details on the

available parameters, refer to “Front Panel Operations”

(page 23).

When the [PANEL LOCK] indicator !6 is lit in orange, front

panel operations are locked, and settings cannot be edited.

Defeat the lock if you want to perform these operations.

i [MUTE] A/B/C/D indicators

When you mute an output channel by operating the unit

itself or by operations via the [REMOTE] connector @7 or

the editor, the indicator of the corresponding channel will

light yellow.

o [MUTE] button

By holding down the [MUTE] button and pressing the

[SELECT] button t, you can switch muting on/off for the

channel selected by the [SELECT] button. When muting

turns on, the [MUTE] indicator i will light in yellow.

When the [PANEL LOCK] indicator !6 is lit, front panel

operations are locked, and channel mute operations are not

possible. Defeat the lock if you want to perform these opera-

tions.

!0 [POWER] indicator

This will light in green when the power supply is turned on

by the power switch q.

It will flash when the unit is switched to standby mode via

the [REMOTE] connector or the editor.

!1 [ALERT] indicator

This will flash or light when an abnormality occurs in the

unit.

If this is flashing, note the indication in the display and refer

to “Alert Numbers and Content” (page 27).

If it is lit, stop operating the unit. After a time, the indicator

will change to flashing, and an alert number will appear in

the display.

!2 [NETWORK] indicator (XMV4280/XMV4140 only)

This will light green if the XMV is in a linked state with an

external device via the network connector !9. It will flash

while data is being communicated.

!3 [YDIF] indicator (XMV4280/XMV4140 only)

This will light green when the [YDIF] connector @0 is con-

nected normally and a valid word clock is being input.

Connector

[SIGNAL]

indicators

used for

(*1)

Indicator

illumina-

tion status

Analog input connectors @4

input

-40dBFS or

[YDIF] connectors @0

(XMV4280/XMV4140)

Dante [PRIMARY] connector

Dante [SECONDARY] connec-

tor @1

(XMV4280-D/XMV4140-D)

[SPEAKERS] output connec-

tors @6

output

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

!4 [PRIMARY]/[SECONDARY] indicators

(XMV4280-D/XMV4140-D only)

These show the communication status of the Dante [PRI-

MARY]/[SECONDARY] connectors @1. They flash rapidly

in green if the Ethernet cables are connected properly.

!5 [SYNC] Indicators

(XMV4280-D/XMV4140-D only)

These show the operating status of the Dante network. If the

green (upper) indicator lights, the unit is operating as a word

clock slave and synchronizing to the word clock. If the green

indicator flashes, the unit is operating as the word clock mas-

ter. If the power to the unit is turned on but the green indica-

tor is turned off, the unit is not functioning properly. In this

case, refer to the “Warning Messages” section (see page 29).

If the orange indicator lights or flashes, refer to the “Warning

Messages” section.

!6 [PANEL LOCK] indicator

This lights or flashes according to the state of the front panel

lock. To specify the front panel lock setting, use the Device

setup DIP switch @3.

!7 [FUNCTION] button

Use this to check or change the operating mode of the

XMV’s front panel. For details on how to perform front

panel operations, refer to “Front Panel Operations” (page

23).

!8 Cooling vent

Located behind the vent is a variable speed cooling fan that

draws air in from the front and exhausts it through the rear.

The fan speed will automatically vary according to the tem-

perature.

Please be sure that you do not block the air intakes or

exhaust vents. You should also clean the air intakes and

exhaust vents regularly. If the air intakes are clogged with

dust or debris, the unit will overheat, which may result in the

unit shutting down.

Indicator Status

Lit

Front panel operations are locked. Lock

will be temporarily defeated if you press

the [FUNCTION] button !7 and the

[SELECT] A button t.

Unlit Front panel operations are not locked.

Flashing

Lock is temporarily defeated. When the

XMV is restarted, it will be in a locked

state.

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

XMV4280/XMV4140

XMV4280-D/XMV4140-D

!9 Network connector (XMV4280/XMV4140 only)

This is a 100BASE-TX Ethernet connector that allows the

unit to be connected to a computer via an Ethernet cable.

@0 [YDIF] connectors (XMV4280/XMV4140 only)

These are RJ-45 connectors that allow the unit to be con-

nected via an Ethernet cable to another YDIF-equipped

device so that audio signals and word clock signals can be

transmitted and received. Using a ring connection (YDIF

connection), you can connect to other devices equipped with

a [YDIF] connector. For details on settings for receiving

audio signals via the [YDIF] connector, refer to “Front Panel

Operations” (page 23).

Cables used for this connection should be 30 meters or less

between devices. Up to eight devices can be connected in a

network with YDIF connection.

For information on connections that use [YDIF] connectors,

refer to the “MTX Setup Manual.”

Rear Panel

1 2 3 4 5 6 7 8

@8@7@5!9 @9

@4 @6

@0 @2

1 2 3 4 5 6 7 8

@8@7@5 @9

@4 @6

NOTE

• Use a CAT5e or better STP (Shielded Twisted Pair) cable

for the network connection to prevent electromagnetic

interference.

• When using MTX-MRX Editor to control the XMV, you

must connect the MTX.

NOTE

To prevent electromagnetic interference, make connections

to the [YDIF] connector using a CAT5e or better STP

(Shielded Twisted Pair) cable in which all pins are con-

nected with a straight connection.

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

@1 Dante [PRIMARY]/[SECONDARY] connectors

(XMV4280-D/XMV4140-D only)

These are RJ-45 connectors that allow the unit to be con-

nected to another Dante device such as the MTX5-D via an

Ethernet cable. The Dante [PRIMARY] connector can also

be used to connect to a computer via an Ethernet cable. To

connect, refer to the “MTX-MRX Editor User Guide.”

@2 [UNIT ID] rotary switch

If multiple devices such as XMVs or MTXs are connected

on the same network, this rotary switch enables you to spec-

ify the UNIT ID that identifies each unit individually.

XMV4280/XMV4140

With the combination of the device setup DIP switches

1–3 @3 for upper digits and the rotary switch for lower dig-

its, the UNIT ID can be specified in a maximum of 127

values, from “01” to “7F.”

XMV4280-D/XMV4140-D

With the rotary switch (HIGH) used for upper digits and

the rotary switch (LOW) for lower digits, the UNIT ID can

be specified in a maximum of 254 values, from “01” to

“FE.”

@3 Device setup DIP switch

This DIP switch is used to make settings for the XMV. Refer

to the following for details on the settings.

Refer to the following for details.

XMV4280/XMV4140

XMV4280-D/XMV4140-D

NOTE

• Use a CAT5e or better STP (Shielded Twisted Pair) cable

for the connection to the Dante [PRIMARY]/[SECOND-

ARY] connectors to prevent electromagnetic interference.

Make sure that the metal parts of the plugs are electrically

connected to the STP cable shield by conductive tape or

comparable means.

• Connect only Dante-compatible devices or GbE-compati-

ble devices (including a computer).

• Since Dante-compatible equipment made by Yamaha

such as the XMV4280-D/XMV4140-D contains a built’-in

network switch, the number of hops will be two or more.

For this reason, the 0.15 msec Latency setting in Dante

Controller will be grayed-out and unavailable.

NOTE

• Do not use “00” or “FF” as the UNIT ID.

•After you set the [UNIT ID] rotary switch, turn the power to

the unit off and then on.

NOTE

To change the switch settings, turn off the power to the unit.

If you change the settings while the power is on, the change

will not be effective until you turn the unit off and then on.

Switch Status

Indicates the switch is in the upward posi-

tion.

Indicates the switch is in the downward posi-

tion.

NOTE

Switch 1 and 2 are not used for the XMV4280-D/XMV4140-

D. Use the swiches in the factory set state (upward).

12345678

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 Switch 1–3 (UNIT ID)

(XMV4280/XMV4140 only)

Use the DIP switches 1–3 to specify the upper digit, and

use the [UNIT ID] rotary switch @2 to specify the lower

digit to set a maximum of 127 combinations of UNIT ID

in the range of 01 through 7F (127).



Switch 3 (SECONDARY PORT)

(XMV4280-D/XMV4140-D only)

This sets the Dante [SECONDARY] connector @1 on the

rear panel as to whether it will be used for daisy chain

connection or redundant. For details on the connection,

refer to the “MTX-MRX Editor User Guide.”



Switch 4 (LED DIMMER)

This specifies the brightness of the front panel indicators

and display.



Switch 5 (PANEL LOCK)

This specifies the front panel lock setting (locks all panel

operations including the [MUTE] button o and attenua-

tion adjustments). By selecting the LOCK setting after

you’ve completed all settings, you can prevent the vol-

ume or mute settings from being inadvertently changed.

Even if the LOCK setting is selected, you can temporarily

unlock the panel by pressing the [FUNCTION] button !7

and the [SELECT] A button t. The panel will be re-

locked when one minute has passed without any opera-

tion being performed, or when you once again press the

[FUNCTION] button and the [SELECT] A button, or

when you turn off the power.



Switch 6 (IP SETTING)

This selects whether the UNIT ID value will be used as

the IP address for the unit to communicate with a com-

puter, or whether the IP address will be assigned by the

editor or the DHCP server.

DIP Switches

Setting Description

The UNIT ID’s

upper digit is

set to 0.

The setting range of the

[UNIT ID] rotary switch is

from 01 through 0F.

The UNIT ID’s

upper digit is

set to 1.

The setting range of the

[UNIT ID] rotary switch is

from 10 through 1F.

The UNIT ID’s

upper digit is

set to 2.

The setting range of the

[UNIT ID] rotary switch is

from 20 through 2F.

The UNIT ID’s

upper digit is

set to 3.

The setting range of the

[UNIT ID] rotary switch is

from 30 through 3F.

The UNIT ID’s

upper digit is

set to 4.

The setting range of the

[UNIT ID] rotary switch is

from 40 through 4F.

The UNIT ID’s

upper digit is

set to 5.

The setting range of the

[UNIT ID] rotary switch is

from 50 through 5F.

The UNIT ID’s

upper digit is

set to 6.

The setting range of the

[UNIT ID] rotary switch is

from 60 through 6F.

The UNIT ID’s

upper digit is

set to 7.

The setting range of the

[UNIT ID] rotary switch is

from 70 through 7F.

DIP Switches Setting Description

DAISY CHAIN

The Dante [SECOND-

ARY] connector is used

for a daisy chain connec-

tion. A signal at the

Dante [PRIMARY] con-

nector will be transmitted

to the next device in the

chain as is.

REDUNDANT

The Dante [SECOND-

ARY] connector is used

for a redundant network.

It will function as backup

connection, independent

of the network to which

the Dante [PRIMARY]

connector is connected.

DIP Switches

Setting Description

OFF Normal brightness.

Reduced brightness. Use

this setting if the indicators

and the display are too

bright.

NOTE

The brightness of the [POWER] indicator !0 will not be

reduced.

DIP Switches

Setting Description

UNLOCK

The front panel will not be

locked.

LOCK

Front panel operations

other than the power will be

locked.

DIP Switches

Setting Description

UNIT ID

The IP address will be

specified using the UNIT ID

value.

The IP address will be

192.168.0.xxx (xxx is the

UNIT ID value).

However, if the UNIT ID is

“FF,” xxx is 127.

The IP address will be

specified by the editor or the

DHCP server.

NOTE

Set this to the “UNIT ID” position the first time you con-

nect this device to a computer after purchase. After

specifying the IP address from the editor, change this

switch to the “PC” position.

Controls and Functions

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 Switches 7 and 8 (START UP MODE)

These specify the startup mode.

@4 Analog input connectors

These are Euroblock 3-pin analog audio input connectors.

For details on settings for receiving audio signals via the

analog input connectors, refer to “Front Panel Operations”

(page 23).

For details on how to attach Euroblock connectors, refer to

the “Connections and Setting Up” section entitled “Connect-

ing the Analog Inputs (Euroblock)” (page 16).

@5 [SPEAKERS] DIP switch

This DIP switch makes settings for the XMV’s amplifier in

groups of two channels.

Switches 1 through 4 specify the output setting for channels

C and D, and switches 5 through 8 specify the output setting

for channels A and B.

Use these switches to make the following settings. The out-

put signals from the output connectors under each setting are

as follows.

In “Output from each connector,” the meaning of the indica-

tions is as follows: G: ground, Nrm: normal output, Inv:

inverted output, N/A: connection prohibited (not available).

* If this setting is chosen, Double Power mode is turned on

and input/output will be disabled for channels B and D.

 Low impedance connection / high impedance

connection (switches 1 and 5)

These select either a low impedance connection or a high

impedance connection. Set them as appropriate for the

connected speakers and the way in which the speakers are

connected. For details on connections, refer to “High-

impedance and Low-impedance Connections” (page 30).



Impedance (switches 3 and 7)

When using a low impedance connection, set these as

appropriate for the impedance of the speakers that are

connected. Check the specifications of the speakers.

For example if two 8Ω speakers are connected in parallel,

the total impedance will be 4Ω.



Double Power mode (switches 4 and 8)

When a low impedance connection is used, these

switches specify the output of the amplifier. If the 280W

{140W} setting is selected, input/output is enabled for

both channels. If the 560W {280W} setting is selected,

the output from the amplifier will be doubled, but input/

output will be disabled for channels B and D.



70V/100V (switches 2 and 6)

When a high impedance connection is used, these

switches specify the maximum output voltage (Vrms) of

the amplifier.

@6 [SPEAKERS] output connectors

These are barrier strip type speaker output connectors. For

details on how to make connections to a barrier strip, refer to

the “Connections and Setting Up” section entitled “Connect-

ing Speaker Cables” (page 18).

@7 [REMOTE] connector

This is a Euroblock 3-pin connector that allows muting/

unmuting of all channels and power-on/standby to be con-

trolled remotely. For details, refer to “[REMOTE] and

[FAULT OUTPUT] Connectors” (page 21).

@8 [FAULT OUTPUT] connector

This is a Euroblock 3-pin connector that allows an external

device to be notified when a fatal malfunction occurs in this

unit. NC and C will be shorted when the amplifier is operat-

ing normally; NO and C will be shorted when a problem

occurs (page 21).

If a problem occurs, the [PROTECTION] indicator w will

light in orange.

@9 [AC IN] connector

Connect the supplied AC power cord here. First connect the

AC power cord to the connector on the rear panel of this unit,

then plug it into an appropriate AC power outlet.

DIP Switches

Setting Description

RESUME

The unit will start up nor-

mally.

INITIALIZE

The internal memory will be

initialized. For details on the

memory that will be initial-

ized, refer to “Initializing the

Internal Memory” (page 25).

Description

Amplifier

output type

Switches 1–4

(channels C

and D)

Switches 5–8

(channels A

and B)

Output from each

connector

Channels

A and C

Channels

B and D

+–+–

Low-impedance connection

280W{140W},

8Ω

Unbalanced

output

Nrm G G Inv

560W{280W}*,

8Ω

Balanced

output (BTL)

Nrm Inv

N/A N/A

280W{140W},

4Ω

Unbalanced

output

Nrm G G Inv

560W{280W}*,

4Ω

Unbalanced

output

Nrm G

N/A N/A

High-impedance connection

70V,

250W{125W}

Balanced

output (BTL)

Nrm Inv Nrm Inv

100V,

250W{125W}

Balanced

output (BTL)

Nrm Inv Nrm Inv

NOTE

• To change the switch settings, turn off the power to the

unit. If you change the settings while the power is on, the

change will not be effective until you turn the unit off and

then back on again.

• Do not connect negative connectors of different channels.

It may cause the device to malfunction.

• For information on BTL connection, refer to “BTL (Bal-

anced Transformer Less) Connection” (page 31).

CAUTION

Before connecting or disconnecting the power cord,

make sure that the power to the unit is turned OFF.

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

Connections and Setting Up

This chapter explains how to set up the XMV to input analog

signals.

If you are using the XMV along with the MTX, refer to the

“MTX Setup Manual.” Refer to this manual for details regard-

ing the following items, even if you are using the XMV along

with the MTX.

• Making settings for speaker output

• Connecting the speaker output connectors

• Making high pass filter (HPF) settings

• Lowering the brightness of the indicators and the display

• Locking the panel

Here we will make and verify the input/output settings as out-

lined below.

 Rack-mounting the Unit

Refer to “Precautions for Rack Mounting” (page 8), and

mount the XMV in your rack.

 Checking the Device Setup DIP Switch Set-

tings

Make sure that all of the rear panel’s device setup DIP

switches (page 13) are in the upward position.

 Connecting the Analog Inputs (Euroblock)

Connect the analog outputs of your mixer or other device to

the analog input connectors (page 15).

You must use the supplied Euroblock plugs with tabs.

If these have been lost, please contact your Yamaha dealer.

Setup for Analog Signal Input

Explanation Page

Rack-mounting the Unit 16

Checking the Device Setup DIP Switch Settings 16

Connecting the Analog Inputs (Euroblock) 16

Making Settings for Speaker Output17

Connecting Speaker Cables 18

Connecting the Power Cord 19

Turning the Power On 19

Enabling Analog Input19

Making High Pass Filter (HPF) Settings 19

Checking the Wiring 20

Lowering the Brightness of the Indicators and the

Display

Locking the Front Panel 20

CAUTION

Steps earlier than “Turning the Power On” must be per-

formed with the power off. If you perform these steps with

the power on, the settings might not be applied, or you

might be subject to electrical shock if you touch the con-

nectors.

12345678

Cable preparation

• To prepare the cable for attachment to a Euroblock

connector, strip the wire as shown in the illustration

using stranded wire to make connections. With a

Euroblock connection, stranded wires may be prone

to breakage because of metal fatigue due to the

weight of the cable or due to vibration. Bundle the

cables and the Euroblock tabs using the supplied

cable ties (page 17). When rackmounting your

equipment, use a lacing bar when possible to bun-

dle and fasten the cables.

• If cables will be frequently connected and discon-

nected, as in the case of a portable installation, we

recommend that you use f

errules

with insulation

sleeves. Use a ferrule whose conductor portion has

an external diameter of 1.6 mm or less, and a length

of approximately 7 mm (such as the AI0,5-6WH

made by the Phoenix Contact corporation).

approx.

7 mm

approx.20 mm

NOTE

Do not tin (plate with solder) the exposed end.

1.6 mm or less

approx.

7 mm

Connections and Setting Up

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

1. Loosen terminal screws.

2. Insert cables.

3. Securely tighten terminal screws.

Pull the cables (not too strongly) to confirm that they are

securely connected.

4. Bundle the cables and the Euroblock tab

using the supplied cable tie.

5. Insert the Euroblock plug into the Analog

input connector of the device.

 Making Settings for Speaker Output

Use the rear panel [SPEAKERS] DIP switches to make the

appropriate settings for the XMV’s speaker output.

The method of connection will differ depending on whether

you’re using a low impedance connection or a high imped-

ance connection.

Low-impedance connection

High-impedance connection

For details, refer to “High-impedance and Low-impedance

Connections” (page 30).

The explanation of the settings is divided into the following

sections.

 When using low impedance connections (page

17)

 When using low impedance connections with

Double Power mode (page 18)

 When using high impedance connections

(page 18)

Since these settings can be made independently for channels

A/B and channels C/D, you can use more than one of the

above methods

 When using low impedance connections

Depending on the impedance (4Ω or 8Ω) of the connected

speakers, set the [SPEAKERS] DIP switches as follows.

NOTE

A slotted screwdriver with a blade width of about 3 milli-

meters is recommended.

NOTE

Trim any excess part of the cable tie as necessary.

Loosen.

Slotted screwdriver

Terminal screw

Euroblock plug

Tab

3 mm or less

–

NOTE

To change the switch settings, turn off the power to the unit.

If you change the settings while the power is on, the change

will not be effective until you turn the unit off and then back

on again.

Setting

Switches 1–4

(channels C and D)

Switches 5–8

(channels A and B)

280W{140W}, 8Ω

280W{140W}, 4Ω

NOTE

If you make settings for low impedance connections, the

HPF will automatically be turned OFF.

8Ω/4Ω

10W 10W 10W 10W 10W

70V/100V

Speaker transformer

Connections and Setting Up

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

The XMV features a switch function between 8Ω and 4Ω to

guarantee the output in case it is connected to a speaker with

an impedance of 8Ω or higher.

If you connect a speaker with an impedance of 8Ω or higher,

set the [SPEAKERS] DIP switches to 8Ω. If you connect a

speaker with an impedance of 4Ω or higher, but lower than

8Ω, set the [SPEAKERS] DIP switches to 4Ω.

 When using low impedance connections with

Double Power mode

If you use Double Power mode, input/output will be dis-

abled for channels B and D.

Depending on the impedance (4Ω or 8Ω) of the connected

speakers, set the [SPEAKERS] DIP switches as follows.

 When using high impedance connections

Depending on the specifications (70V or 100V) of the

system in which this unit is being installed, set the

[SPEAKERS] DIP switches as follows.

 Connecting Speaker Cables

The [SPEAKERS] output connectors (page 15) on the rear

panel are barrier strip type connectors. We will explain con-

nections using a spade lug and connections using a bare con-

ductor.

 If using a spade lug

From below, insert the spade lug all the way, and tighten

the screw.

 If using a bare conductor

Wrap the conductor around the barrier strip terminal as

shown below, and tighten the screw. Be sure that the bare

wire does not touch the chassis.

Total impedance(x) Setting

4Ω x 8Ω4Ω

8Ω x 8Ω

Setting

Switches 1–4

(channel C)

Switches 5–8

(channel A)

560W{280W}, 8Ω

560W{280W}, 4Ω

NOTE

If you make settings for low impedance connections, the

HPF will automatically be turned OFF.

Setting

Switches 1–4

(channels C and D)

Switches 5–8

(channels A and B)

70V

100V

NOTE

When the device is turned on, it will set HPF to 80 Hz, if

the device is set to high impedance connection. If the

device is set to low impedance connection, HPF will be

not set.

CAUTION

Make sure that the power is turned off. If the power is

on, you risk electrical shock.

NOTE

• If the [SPEAKERS] DIP switch 4 (page 15) is in the

lowered position (Double Power mode), even if you do

connect a cable, audio will not be output from channel

• If the [SPEAKERS] DIP switch 8 is in the lowered posi-

tion (Double Power mode), even if you do connect a

cable, audio will not be output from channel B.

•Ensure that tension is not applied to the speaker cable.

• Connect the cables so that the amplifier’s “+” and “-”

symbols match those of the speaker. If they are

reversed, the polarity will be reversed.

TIPS

Since a large amount of current can flow in a speaker

cable, a magnetic field will be generated. If sensitive cir-

cuits such as a microphone input cable or a microphone

amp are located near a speaker cable, electromagnetic

induction may produce noise in the input cable or circuit.

Input cables and devices that contain sensitive circuits

should be kept at a distance from speaker cables; we

also recommend that you fasten the cables in place.

0.15"

(

3.7mm)

0.31"

(

7.8mm)

15mm*

* Actual size Speaker cable

Wire should

not touch

the chassis.

Connections and Setting Up

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 Connecting the Power Cord

Connect the included power cord to the [AC IN] connector

(page 15) on the rear panel. First connect the AC power cord

to the connector on this unit, then plug it into an appropriate

AC power outlet.

 Turning the Power On

Use the front panel power switch (page 9) to turn the power

on.

 Enabling Analog Input

Using the front panel, enable analog input as follows.

1. While holding down the [FUNCTION] but-

ton, turn the encoder to make the display

indicate “SRC.”

The control mode will change to “Analog/digital input

selection.”

2. Press the [SELECT] button of the channel

for which you want to enable the analog

input.

The [SELECT] indicator of the selected channel will

light.

3. Take your finger off the [FUNCTION] button,

and turn the encoder to make the display

indicate “ANA.”

Input from the analog input connectors will be enabled.

 Making High Pass Filter (HPF) Settings

If the unit is set for low impedance connections, the HPF

will be OFF. If the unit is set for high impedance connec-

tions, the 80 Hz HPF will be enabled.

If you want to change this setting, proceed as follows.

1. While holding down the [FUNCTION] but-

ton, turn the encoder to make the display

indicate “HPF.”

The control mode will change to “HPF.”

2. Press the [SELECT] button of the channel

for which you want to make HPF settings.

The [SELECT] indicator of the channel whose HPF you

are setting will light.

3. Turn the encoder to select the desired HPF

setting.

The available HPF settings are OFF / 40 Hz / 80 Hz.

CAUTION

You must turn off the power before connecting the

power cord.

CAUTION

Before you turn the power on, make sure that audio

signals are not being input to the analog input connec-

tors. If audio signals are being input, excessive input

will be applied to the speakers when the power is

turned on, possibly damaging the speaker system or

damaging your hearing by high-volume sound. If there

is a problem with the speakers or the wiring, the pro-

tection circuit will operate immediately when the power

is turned on. Check whether there might be a problem

with the wiring.

NOTE

If a certain period of time elapses without any operation

being performed, the unit will return to Attenuation set-

ting operating mode.

NOTE

• In order to protect the amplifier, the HPF cannot be

turned OFF if high impedance connections are used.

•If you’re using a sub-woofer with high-impedance con-

nections, we recommend that you change the HPF

setting to 40 Hz.

•If you’re using a full-range speaker with high-imped-

ance connections, the amplifier’s protection circuit may

operate if the HPF is set to other than 80 Hz. We rec-

ommend that you use the 80 Hz setting.

• If a certain period of time elapses without any opera-

tion being performed, the unit will be placed in Attenua-

tion setting operating mode.

NOTE

If the device is set as follows, the HPF settings will be

changed automatically.

startup

Current startup

HPF

[SPEAKERS]

DIP switches

(page 15)

Device setup

DIP switches 7

and 8 (page 15)

[SPEAKERS]

DIP switches

(page 15)

Hi impedance

RESUME

Low impedance

(changed)

Off

Hi impedance

(not changed)

Same as

the previ-

ous startup

Low impedance

(not changed)

Same as

the previ-

ous startup

Hi impedance

(changed)

80 Hz

(Unrelated to

the setting at

startup)

INITIALIZE

Low impedance Off

Hi impedance 80 Hz

Connections and Setting Up

XMV4280/XMV4140/XMV4280-D/XMV4140-D Owner’s Manual

 Checking the Wiring

Here we’ll explain how to change the attenuation settings

and switch muting on/off, which you will need to do when

checking the wiring.

Before you check the wiring, we recommend that you set the

attenuator of all channels to the lowest setting (-99 dB) to

prevent speaker damage.

To check the wiring, you’ll need to be outputting an audio

signal from the mixer or other device that’s connected to the

analog input connectors.

 Changing the attenuator setting

Here’s how to change the attenuator setting.

1. While holding down the [FUNCTION] but-

ton, turn the encoder to make the display

indicate “ATT.”

2. Press the [SELECT] button of the channel

whose setting you want to adjust.

The [SELECT] indicator of the selected channel will

light.

3. Turn the encoder to gradually raise the

attenuator setting from -99, and verify

that sound is produced from the speaker.

 Switching the mute setting on/off

While holding down the [MUTE] button,

press the [SELECT] button of the channel

that you want to control.

When mute is on, the [MUTE] indicator will light; when

mute is off, the [MUTE] indicator will be unlit.

 Lowering the Brightness of the Indicators

and the Display

If the front panel LED indicators are too bright, you can

lower their brightness.

After turning the power off, set the rear panel device setup

DIP switch 4 (LED DIMMER) to the lower position (ON).

The next time you turn the power on, the unit will start up

with decreased indicator brightness.

 Locking the Front Panel

By locking the panel you can disable front panel operations

other than controlling the power (front panel lock).

When this unit is used as part of an installed system, you can

lock down the settings by disabling operations from the front

panel, thus preventing inadvertent changes.

After turning the power off, set the rear panel device setup

DIP switch 5 (PANEL LOCK) to the lower position

(LOCK). The next time you turn the power on, the unit will

start up with the front panel locked.

Even in the locked state, you can temporarily defeat the

panel lock by pressing the [FUNCTION] button and the

[SELECT] A button. However, it will be re-locked when any

of the following conditions occur.

• One minutes elapses without any operation being per-

formed after the panel is temporarily unlocked

• You press the [FUNCTION] button and the [SELECT] A

button

• You turn the power off

The lock status is shown by the front panel [PANEL LOCK]

indicator.

• Locked: lit

• Not locked: unlit

• Temporarily unlocked: flashing

NOTE

If the speakers are remotely located and you are unable to

check the signal output easily, changing the [SIGNAL] indi-

cator (page 10) setting to “output” will allow you to check

whether current is flowing to the speakers. For details on

switching the indicator setting, refer to “Front Panel Opera-

tions” (page 23).

NOTE

The brightness of the [POWER] indicator will not be

reduced.

Страница загружается...

Yamaha XMV8140, XMV4140, XMV4140-D, XMV4280, XMV4280-D, XMV8140-D, XMV8280, XMV8280-D Инструкция по применению

Похожие модели бренда

Модели других брендов