Generac 70kW QT07068AVAC Руководство пользователя

This manual should remain with the unit.

Not intended for use in critical life

support applications.

OUTDOOR INSTALLATION ONLY

Installation Manual

Stationary Emergency Generator

INTRODUCTION ....................................................................... 1

Read this Manual Thoroughly ........................................ 1

How to Obtain Service ................................................... 1

SAFETY RULES ....................................................................... 2

GENERAL INFORMATION ........................................................ 4

1.1 Generator Installation ..................................................... 4

1.2 Before Installation .......................................................... 4

1.3 Generator Location ........................................................ 5

1.4 Generator Mounting and Support ................................... 5

1.5 Unpacking ..................................................................... 6

1.6 Lifting the Generator ...................................................... 6

1.7 Generator Placement ..................................................... 6

1.8 Fuel Systems ................................................................ 6

1.9 Calculating Volumetric Flow Rate and Pipe Size ........... 10

1.10 Electrical Connections ................................................. 13

1.11 Battery Installation ....................................................... 13

1.12 Generator Activation .................................................... 14

INSTALLATION ...................................................................... 16

2.1 Transfer Switch ........................................................... 16

2.2 Unpacking ................................................................... 16

2.3 Mounting..................................................................... 16

OPERATION ........................................................................... 16

3.1 Basic Standby Electric System .................................... 16

3.2 Standby Circuit Isolation Method ................................. 16

3.3 Total Circuit Isolation Method....................................... 17

3.4 All Transfer Switch Installations ................................... 17

3.5 Nexus Transfer Switches ............................................. 18

3.6 Connection Diagrams .................................................. 18

3.7 Wire Recommendations/Sizing .................................... 20

Manual de instalación .......................23

Руководство по установке ....................47

Manual de instalação

............................71

Table of Contents

WARNING!

California Proposition 65

Engine exhaust and some of its constituents are known to the state of California to cause cancer,

birth defects, and other reproductive harm.

WARNING!

California Proposition 65

This product contains or emits chemicals known to the state of California to cause cancer,

birth defects, and other reproductive harm.

INTRODUCTION

Thank you for purchasing this model of the standby generator

set.

Every effort was expended to make sure that the information and

instructions in this manual are both accurate and current at the

time the manual was written. However, the manufacturer reserves

the right to change, alter or otherwise improve this product(s) at

any time without prior notice.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the nearest

Dealer for starting, operating and servicing procedures.

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

service or operation that may be hazardous if performed incor-

rectly or carelessly. Observe them carefully. Their definitions are

as follows:

INDICATES A HAZARDOUS SITUATION OR ACTION WHICH, IF

NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

Indicates a hazardous situation or action which, if not

avoided, could result in death or serious injury.

Indicates a hazardous situation or action which, if not

avoided, could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:



This symbol points out important safety information that,

if not followed, could endanger personal safety and/or

property of others.





This symbol points out potential explosion hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical shock hazard.

HOW TO OBTAIN SERVICE

When the generator requires servicing or repairs, contact a Dealer

for assistance. Service technicians are factory-trained and are

capable of handling all service needs.

When contacting a Dealer about parts and service, always supply

the complete Model number, Serial number and Type Code (where

applicable), of the unit as given on the Data Label affixed to the

unit.

1

Introduction

2

Study these SAFETY RULES carefully before installing, operating or

servicing this equipment. Become familiar with this Owner’s Manual

and with the unit. The generator can operate safely, efficiently and

reliably only if it is properly installed, operated and maintained. Many

accidents are caused by failing to follow simple and fundamental

rules or precautions.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive.

If using a procedure, work method or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the generator unsafe.



Despite the safe design of this generator,

operating this equipment imprudently, neglect-

ing its maintenance or being careless can

cause possible injury or death. Permit only

responsible and capable persons to install,

operate or maintain this equipment.



Potentially lethal voltages are generated by

these machines. Ensure all steps are taken to

render the machine safe before attempting to

work on the generator.



Parts of the generator are rotating and/or hot

during operation. Exercise care near running

generators.



Generator exhaust gases contain DEADLY

carbon monoxide gas. This dangerous gas, if

breathed, can cause headaches, fatigue, diz-

ziness, vomiting, confusion, seizures, nausea,

fainting, unconsciousness or even death.

Operate this equipment only in the open air

where adequate ventilation is available.

GENERAL HAZARDS

• For safety reasons, the manufacturer recommends that this

equipment be installed, serviced and repaired by an authorized

dealer or other competent, qualified electrician or installation

technician who is familiar with applicable codes, standards

and regulations. The operator also must comply with all such

codes, standards and regulations.

• Installation, operation, servicing and repair of this (and related)

equipment must always comply with applicable codes, stan-

dards, laws and regulations. Adhere strictly to local, state and

national electrical and building codes. Comply with regulations

the Occupational Safety and Health Administration (OSHA) has

established. Also, ensure that the generator is installed, operat-

ed and serviced in accordance with the manufacturer’s instruc-

tions and recommendations. Following installation, do nothing

that might render the unit unsafe or in noncompliance with the

aforementioned codes, standards, laws and regulations.

• Keep hands, feet, clothing, etc., away from drive belts, fans,

and other moving or hot parts. Never remove any drive belt or

fan guard while the unit is operating.

• When working on this equipment, remain alert at all times.

Never work on the equipment when physically or mentally

fatigued.

• Inspect the generator regularly, and promptly repair or replace

all worn, damaged or defective parts using only factory-

approved parts.

• Before performing any maintenance on the generator, discon-

nect its battery cables to prevent accidental start-up. Disconnect

the cable from the battery post indicated by a NEGATIVE, NEG

or (–) first. Reconnect that cable last.

• Never use the generator or any of its parts as a step. Stepping

on the unit can stress and break parts, and may result in dan-

gerous operating conditions from leaking exhaust gases, fuel

leakage, oil leakage, etc.

ELECTRICAL HAZARDS

• All generators covered by this manual produce dangerous elec-

trical voltages and can cause fatal electrical shock. Utility power

delivers extremely high and dangerous voltages to the transfer

switch as well as the standby generator. Avoid contact with

bare wires, terminals, connections, etc., on the generator as

well as the transfer switch, if applicable. Ensure all appropriate

covers, guards and barriers are in place before operating the

generator. If work must be done around an operating unit, stand

on an insulated, dry surface to reduce shock hazard.

• Do not handle any kind of electrical device while stand-

ing in water, while barefoot, or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.



Save These Instructions – The manufacturer suggests that these rules for safe operation be copied and

posted in potential hazard areas. Safety should be stressed to all operators, potential operators, and ser-

vice and repair technicians for this equipment.



Save These Instructions – This manual contains important instructions that should be followed during

installation of the generator and batteries.

Safety Rules

3

• If people must stand on metal or concrete while installing,

operating, servicing, adjusting or repairing this equipment,

place insulative mats over a dry wooden platform. Work on the

equipment only while standing on such insulative mats.

• The National Electrical Code (NEC), Article 250 requires the

frame and external electrically conductive parts of the generator

to be connected to an approved earth ground and/or ground-

ing rods. This grounding will help prevent dangerous electrical

shock that might be caused by a ground fault condition in

the generator set or by static electricity. Never disconnect the

ground wire.

• Wire gauge sizes of electrical wiring, cables and cord sets must

be adequate to handle the maximum electrical current (ampac-

ity) to which they will be subjected.

• Before installing or servicing this (and related) equipment, make

sure that all power voltage supplies are positively turned off at

their source. Failure to do so will result in hazardous and pos-

sibly fatal electrical shock.

• Connecting this unit to an electrical system normally supplied

by an electric utility shall be by means of a transfer switch so as

to isolate the generator electric system from the electric utility

distribution system when the generator is operating. Failure to

isolate the two electric system power sources from each other

by such means will result in damage to the generator and may

also result in injury or death to utility power workers due to

backfeed of electrical energy.

• Generators installed with an automatic transfer switch will crank

and start automatically when normal (utility) source voltage is

removed or is below an acceptable preset level. To prevent such

automatic start-up and possible injury to personnel, disable the

generator’s automatic start circuit (battery cables, etc.) before

working on or around the unit. Then, place a “Do Not Operate”

tag on the generator control panel and on the transfer switch.

• In case of accident caused by electric shock, immediately

shut down the source of electrical power. If this is not pos-

sible, attempt to free the victim from the live conductor. AVOID

DIRECT CONTACT WITH THE VICTIM. Use a nonconducting

implement, such as a dry rope or board, to free the victim from

the live conductor. If the victim is unconscious, apply first aid

and get immediate medical help.

• Never wear jewelry when working on this equipment. Jewelry

can conduct electricity resulting in electric shock, or may get

caught in moving components causing injury.

FIRE HAZARDS

• Keep a fire extinguisher near the generator at all times. Do NOT

use any carbon tetra-chloride type extinguisher. Its fumes are

toxic, and the liquid can deteriorate wiring insulation. Keep the

extinguisher properly charged and be familiar with its use. If

there are any questions pertaining to fire extinguishers, consult

the local fire department.

EXPLOSION HAZARDS

• Do not smoke around the generator. Wipe up any fuel or oil

spills immediately. Ensure that no combustible materials are left

in the generator compartment, or on or near the generator, as

FIRE or EXPLOSION may result. Keep the area surrounding the

generator clean and free from debris.

• This generator may operate using one of several types of fuels.

All fuel types are potentially FLAMMABLE and/or EXPLOSIVE

and should be handled with care. Comply with all laws regulat-

ing the storage and handling of fuels. Inspect the unit’s fuel

system frequently and correct any leaks immediately. Fuel

supply lines must be properly installed, purged and leak tested

according to applicable fuel-gas codes before placing this

equipment into service.

• Gaseous fluids such as natural gas and liquid propane (LP) gas

are extremely EXPLOSIVE. Natural gas is lighter than air, and LP

gas is heavier than air; install leak detectors accordingly.

LOCATION/EXHAUST HAZARDS

• The engine exhaust fumes contain carbon monoxide gas,

which can be DEADLY. This dangerous gas, if breathed in

sufficient concentrations, can cause unconsciousness or even

death. For that reason, adequate ventilation must be provided.

This should be considered prior to installing the generator.

The unit should be positioned to direct exhaust gasses safely

away from any building where people, animals, etc., will not be

harmed. Any exhaust stacks that ship loose with the unit must

be installed properly per the manufacturer's instruction, and in

strict compliance with applicable codes and standards.

• Adequate, unobstructed flow of cooling and ventilating air is

critical to prevent buildup of explosive gases and to ensure cor-

rect generator operation. Do not alter the installation or permit

even partial blockage of ventilation provisions, as this can seri-

ously affect safe operation of the generator.

• Keep the area around the generator clean and uncluttered.

Remove any materials that could become hazardous.

Safety Rules

4

1.1 GENERATOR INSTALLATION

This equipment is a liquid-cooled, engine-driven generator set.

The generator is designed to supply electrical power that operates

critical electrical loads during utility power failure. The unit has

been factory-installed in a weather resistant, all metal enclosure

and is intended for outdoor installation only.



If this generator is used to power electrical

load circuits normally powered by a utility

power source, it is required by code to install

a transfer switch. The transfer switch must

effectively isolate the electric system from the

utility distribution system when the generator

is operating (NEC 701). Failure to isolate an

electrical system by such means results in

damage to the generator and may also result

in injury or even death to utility power workers

due to backfeed of electrical energy.

1.2 BEFORE INSTALLATION

NOTE:

Contact the local inspector or City Hall to make sure you are

aware of all federal, state and local codes that could impact the

installation. Secure all required permits before starting the job.

Before installing this equipment, check the ratings of both the

generator and the transfer switch. Read “Emergency Isolation

Method” and “Total Circuit Isolation Method”.

The generator’s rated wattage/amperage capacity must be

adequate to handle all electrical loads that the unit will power. The

critical (essential) loads may need to be grouped together and

wired into a separate “emergency” distribution panel.



Connecting this generator to an electrical

system normally supplied by an electric utility

shall be by means of a transfer switch, so as

to isolate the electric system from the utility

distribution system when the generator is

operating. Failure to isolate the electric system

by these means will result in damage to the

generator and may also result in injury or death

to utility workers due to backfeed of electrical

energy.



If an open bottom is used, the engine-generator

is to be installed over non-combustible

materials and should be located such that

combustible materials are not capable of

accumulating under the generator set.

Only authorized dealers or qualified, competent installation

contractors or electricians thoroughly familiar with applicable

codes, standards and regulations should install this standby

electric power system. The installation must comply strictly with

all codes, standards and regulations pertaining to the installation.



After the system has been installed, do

nothing that might render the installation in

noncompliance with such codes, standards and

regulations.

1.2.1 NFPA STANDARDS

Applicable national, state, or local laws, codes, and regulations

pertaining to the installation of engine-generator power systems

must be strictly complied with. Always use the current acceptable

version or edition of the applicable code or standard which applies

to your jurisdiction. In the absence of pertinent local laws and

standards, the following published booklets may be used as a

guide (these apply to localities which recognize NFPA and IBC):

1. National Fire Protection Association (NFPA) 70: The NATIONAL

ELECTRIC CODE (NEC) *

2. NFPA 10: Standard for Portable Fire Extinguishers *

3. NFPA 30: Flammable And Combustible Liquids Code *

4. NFPA 37: Standard for Stationary Combustion Engines And

Gas Turbines *

5. NFPA 54: National Fuel Gas Code *

6. NFPA 58: Standard for Storage And Handling Of Liquefied

Petroleum Gases *

7. NFPA 68: Standard On Explosion Protection By Deflagration

Venting *

8. NFPA 70E: Standard For Electrical Safety In The Workplace *

9. NFPA 99: Health Care Facilities Code *

10. NFPA 101: Life Safety Code *

11. NFPA 110: Standard for Emergency and Standby Power

Systems *

12. NFPA 211: Standard for Chimneys, Fireplaces, Vents, and

Solid Fuel Burning Appliances *

13. NFPA 220: Standard on Types of Building Construction *

14. NFPA 5000: Building Code *

15. International Building Code **

16. Agricultural Wiring Handbook ***

17. ASAE EP-364.2 Installation and Maintenance of Farm Standby

Electric Power ****

This list is not all inclusive. Check with the Authority Having Local

Jurisdiction (AHJ) for any local codes or standards which may

be applicable to your jurisdiction. The above listed standards are

available from the following internet sources:

* www.nfpa.org

** www.iccsafe.org

*** www.rerc.org Rural Electricity Resource Council P.O. Box 309

Wilmington, OH 45177-0309

**** www.asabe.org American Society of Agricultural & Biological

Engineers 2950 Niles Road, St. Joseph, MI 9085

Changes to previous standards:

The National Building Code was superseded by the International

Building Code and/or NFPA 5000 Building Code. The local AHJ will

determine which if either applies.

General Information

5

1.3 GENERATOR LOCATION

Install the generator set, in its protective enclosure outdoors,

where adequate cooling and ventilating air always is available.

Consider these factors:

• Install the unit where air inlet and outlet openings will not

become obstructed by leaves, grass, snow, etc. If prevailing

winds will cause blowing or drifting, consider using a windbreak

to protect the unit.

• Install the generator on high ground where water levels will not

rise and endanger it.

• This genset must be installed on a level surface. The base frame

must be level within 1/2 inch all around.

• Allow sufficient room on all sides of the generator for

maintenance and servicing. This unit must be installed in

accordance with current applicable NFPA 37 and NFPA 70

standards, as well as any other federal, state and local codes

for minimum distances from other structures.

• Where strong prevailing winds blow from one direction, face the

generator air inlet openings into the prevailing winds.

• Install the generator as close as possible to the transfer switch.

This reduces the length of wiring and conduit.

• Install the generator as close as possible to the fuel supply,

to reduce the length of piping. HOWEVER, REMEMBER THAT

LAWS OR CODES MAY REGULATE THE DISTANCE.

1.4 GENERATOR MOUNTING AND

SUPPORT

When designing a concrete base slab, all federal, state and local

codes should be followed. Special attention should be given to the

concrete base slab which should exceed the length and width of

the generator by a minimum of 6 inches on all sides.

The mounting pad should be located as close as possible to the

transfer switch and fuel supply. Make sure you leave adequate

room around the generator for service access. Five feet is a good

rule of thumb, but local codes vary.

Place the pad high enough to keep rising water from reaching

the generator. Make sure the generator will have adequate and

unobstructed airflow by choosing an open space free of trees,

shrubs, buildings or other obstructions (Figure 1.1).

Figure 1.1 — Mounting Pad

The unit must be positioned so air vents won’t become clogged

with leaves, grass, snow or debris. Make sure that exhaust fumes

will not enter the building through eaves, windows, ventilation fans

or other air intakes.

Position the electrical conduit for power wiring, control wiring and

the battery charger circuit so the generator can be placed correctly

on the pad (Figure 1.2).

Figure 1.2 — Position Conduit

The concrete pad should be reinforced and deep enough so that

the weight of the pad is equal to the weight of the generator (refer

to the "Generator Mounting and Support" section in this manual).

The length and width of the pad should exceed the length and

width of the generator by at least 6 inches on all sides and the

pad must be level within ½ inch all around. Refer to the installation

diagram supplied with the owner's manual for the correct stub up

area location.

1.4.1 COMBUSTIBLE FLOOR AND ROOF PROTECTION

If the generator must be installed on any combustible floor or roof,

comply with the following rules:

• Place a layer of non-combustible insulation, followed by a layer

of sheet metal beneath the unit’s mounting base rails (Figure

1.3).

• Both the layer of insulation and the sheet metal must extend

beyond the generator base to a distance of at least 6 inches

(15.24 cm) on all sides.

For rooftop or building structure mounting, it is recommended

that spring isolators be installed between the engine frame and

the mounting system. A minimum of six (6) isolators are required

and must be located at the front and rear cross members and the

center of the frame.

General Information

6

Figure 1.3 — Combustible Floor and Roof Protection

6 INCHES

MINIMUM

6 INCHES

MINIMUM

INSULATION

GENERATOR

MOUNTING BASE

SHEET METAL

Since the entire bottom of the genset is now exposed, it should be

covered with a metal plate to keep out small animals and protect

the integrity of the internal parts of the genset. Genset movement is

more intense with spring isolation, so flexible connections for the

fuel and the electrical conduits are also required.

NOTE:

Consult the local building codes which may vary.

1.5 UNPACKING

1.5.1 UNPACKING PRECAUTIONS

Handle shipping cartons and crates with care. Use care to avoid

damage from dropping, bumping, collision, etc. Store and unpack

cartons with the proper side up, as noted on the shipping carton.

1.5.2 INSPECTION

After unpacking, carefully inspect the generator for any damage

that may have occurred during shipment. If loss or damage is

noted at the time of delivery, have the person(s) making delivery

note all damage on the freight bill or affix their signature under the

consignor’s memo of loss or damage.

1.6 LIFTING THE GENERATOR



When lifting or hoisting equipment is used,

be careful not to touch overhead power lines.

Generators that weigh more than 900 pounds

require proper tools, equipment, and qualified

personnel to be used in all phases of handling

and unpacking.

1.7 GENERATOR PLACEMENT

Use a forklift, boom truck or similar equipment with sufficient

capacity to move the generator to the mounting pad area.

The operator should be certified and experienced in generator

installation (Figure 1.4).

Figure 1.4 — Lifting the Generator

Before placing the generator on the pad, inspect for shipping

damage and if necessary, file a claim with the shipper.

After removing the bolts holding the generator base frame to the

wooden pallet, use the lifting eyes on the base frame to lift the

generator onto the pad.

When properly positioned, secure the base frame to the pad with

appropriately sized masonry bolts.

Ground the unit appropriately per NEC and local codes. There is a

ground lug for this purpose attached to the frame rail.

1.8 FUEL SYSTEMS

1.8.1 FUEL CONVERSION

The generator shipped from the manufacturer is configured to

run on natural gas. Refer to the Owner's Manual for details on

converting the generator to run on LP vapor.

1.8.2 INTRODUCTION TO GASEOUS FUEL SYSTEMS



Gaseous fuels, such as LP and natural gas, are

highly volatile and their vapors are explosive.

LP gas is heavier than air and will settle in low

areas. Natural gas is lighter than air and will

settle in high areas. Even the slightest spark

can ignite these fuels and cause an explosion.

For safety, all codes, standards and regulations

pertaining to the installation and use of

gaseous fuels must be strictly complied with.

General Information

7

Local fuel gas codes may vary widely. For that reason, it is

recommended that a local gas distributor or installer be consulted

when installing a gaseous fuel supply system.

In the absence of local fuel gas codes and regulations, booklets

published by the National Fire Protection Association (NFPA) may

be used as sources of information.

Gaseous fuel systems should be installed by a licensed plumber

who is experienced in generator installation and is familiar with

local codes and regulations.

When installing rigid natural gas lines, always use AGA approved

black pipe.

In most applications, a manual shutoff valve and a primary

regulator must be a part of the installation (Figure 1.7).

Figure 1.7 — Manual Shutoff Valve

A section of UL or AGA approved flexible fuel line is required to

protect the rigid fuel line connections against vibration from the

generator.

Installing the flexible fuel line horizontally with as few bends as

possible will allow the flexible section to absorb and mitigate

vibration. Never use a flexible fuel line to avoid an elbow in a rigid

line and never attach gaseous fuel line supports to any part of the

generator. Never install the flex fuel line vertically. Doing so defeats

the purpose of the flexible fuel line (Figure 1.8).

Figure 1.8 — Flexible Fuel Line

After checking all connections for leaks, check the static gas

pressure at the secondary regulator to ensure there is sufficient

pressure to operate the generator (see Owner’s Manual).

If the static pressure is too low, or is higher than 14 inches of water

column, notify the local gas supplier. (Figure 1.9)

Figure 1.9 — Water Column

1.8.3 PROPERTIES OF GASEOUS FUELS

Natural Gas

Natural gas is lighter than air. It is found in the gaseous state at

normal ambient temperatures and pressures. It is highly explosive

and can be ignited at the slightest spark. For that reason, fuel

lines must be free of leaks and adequate ventilation is absolutely

essential.

Local fuel/gas codes usually dictate the maximum pressure at

which natural gas can enter a structure. In order to reduce the

gas pressure to that required by law, a PRIMARY REGULATOR is

required.

LP Gas

Liquefied petroleum (LP) gas is heavier than air. The gas vapors

are explosive and, like natural gas, can be ignited by the slightest

spark.

LP tank pressure is dependent on the ambient temperature and can

be as high as 200 psi. A primary regulator is required at the tank

to reduce the pressure to the required five to 14 inches of water

column for units less than 70kW, or 11 to 14 inches of water

column for units 70kW and larger.

General Information

1.8.4 THE NATURAL GAS SYSTEM

A typical natural gas system is shown in Figure 1.10. The

maximum pressure at which the gas can enter a building is

established by code and may vary from area to area. A primary

regulator is required to reduce gas supply pressures to the required

safe level before the gas enters a structure.

The primary regulator may or may not be provided by the gas

supplier. The gas distribution company will usually provide piping

from the main distribution line to the generator site. It is the

responsibility of the gas supplier to ensure that sufficient gas

pressure is available to operate the primary regulator.

From the primary regulator, gas flows to the generator connection.

A flexible length of gas line is required between rigid piping and

the gas connection at the generator. The generator fuel system

consists of an electrical fuel shutoff valve/regulator assembly and

a gas actuator.

The secondary regulator reduces gas pressure to about five inches

of water column before the gas Is delivered to the actuator.

NOTE:

Gas pressure from the primary regulator (supplied by the

installing contractor) to the generator's fuel shutoff valve should

not exceed 14 inches of water column.

Follow the local codes on selecting the required AGA approved,

and UL listed, for NG application flexible portion of the fuel line

(supplied by the installing contractor).

1.8.5 LP GAS VAPOR WITHDRAWAL SYSTEM

This type of system utilizes the vapors formed above the liquid

fuel in the supply tank (see Figure 1.11). Approximately 10 to 20

percent of the tank capacity is needed for fuel expansion from

the liquid to the vapor state. Gas pressure requirements for an LP

vapor system at the frame of the generator are the same as those

listed for natural gas in "The Natural Gas System". See Table 1 for

information regarding the vapor capacity of LP tanks. The installer

should be aware of the following:

• When ambient temperatures are low and engine fuel

consumption is high, the vapor withdrawal system may not

function efficiently.

• Ambient temperatures around the supply tank must be high

enough to sustain adequate vaporization or the system will not

deliver the needed fuel volume.

• In addition to the cooling effects of ambient air, the vaporization

process itself provides an additional cooling effect.

1.8.6 GASEOUS FUEL SYSTEM PIPING

NOTE:

The information below is to assist in planning gaseous fuel

installation. In NO WAY should this information be interpreted

to conflict with applicable fuel gas codes. Contact the local

jurisdiction if questions arise.

The following general rules apply to piping used in gaseous fuel

systems:

• The piping should be of black iron, rigidly mounted and

protected against vibration.

• Install the supplied length of flexible hose between the generator

connection point and rigid piping.



The supplied flexible hose is not to be installed

underground or in contact with ground. The

flexible hose is for in-line installation only.

Bends, kinks or off-center in-line installation of

flexible hose is NOT allowed.

• Piping must be of the correct size to maintain the required

supply pressures and volume flow under varying conditions

(see Calculating volumetric Flow Rate and Pipe Size).

• Installed piping must be properly purged and leak-tested, in

accordance with applicable codes and standards.

• Use an approved pipe sealant or joint compound on all threaded

fittings, to reduce the possibility of leakage.

NOTE:

In the absence of local purging and leak test standards, NFPA

No. 54 may be used as a guide.

8

General Information

9

Gas Actuator

Primary Regulator

(Supplied by

Installing

Contractor)

Flex Fuel Line

(Supplied

with Unit)

Generator Base

Fuel Shutoff/Regulator

Assembly

Manual Shutoff Valves

Fuel

Tank

11 - 14” Water Column

Recommended (> = 70kW)

5 - 14" Water Column

Recommended (< 70kW)

Figure 1.11 — Typical LP Gas Vapor Withdrawal System

Gas Actuator

Primary Regulator

(Supplied by

Installing

Contractor)

11 - 14” Water Column

Recommended (> = 70kW)

5 - 14" Water Column

Recommended (< 70kW)

Flex Fuel Line

(Supplied

with Unit)

Generator Base

Fuel Shutoff/Regulator

Assembly

Manual Shutoff

Valve

Figure 1.10 — Typical Natural Gas System

General Information

1.9 CALCULATING VOLUMETRIC

FLOW RATE AND PIPE SIZE

If the Owner's Manual identifies the fuel consumption requirements

by a volumetric flow rate (units of ft

3

/hr), skip the next section and

go on to the section, Calculating Pipe Size. If the Fuel Consumption

requirements are given in units of lb/hr, follow the next section,

Calculating Volumetric Flow Rate.

1.9.1 CALCULATING VOLUMETRIC FLOW RATE

Since the fuel consumption requirements (from the owner's

manual) are given as a mass flow (units of lb/hr), the volumetric

flow rate (ft

3

/hr) must be identified before the appropriate pipe

size can be selected. The relationship between the mass flow rate

(lb/hr), density (lb/ft

3

), and volumetric flow rate (ft

3

/hr) can be

described by Equation 1. According to Equation 1, the volumetric

flow rate can be calculated by dividing the mass flow rate by the

density. You may need to contact your fuel vendor to identify the

density or specific gravity for your fuel. If your vendor provides

the specific gravity (relative to air) Table 1 can be used to identify

the appropriate density. Since the density of natural gas and LP is

temperature dependant, the maximum temperature of the fuel (at

the fuel shutoff/regulator assembly) should be measured so the

fuel consumption requirements can be more accurately identified

for the generator. A sample calculation (Example 1) is included in

this section.

Equation 1:

F =

ٝ

—

p



Where:

ṁ

= Mass Flow Rate (lb/hr)

 = Volumetric Flow Rate (ft

3

/hr)

p = Density from Table 1 -

(T-60)

—

C

•

C = 11111 (for Natural Gas) or 3333 (for LP)

T = Temperature of the fuel into the fuel shut-off/regulator

Example 1: Determine the volumetric flow rate for a generator

that requires 91.34 lb/hr of natural gas at 100% load.

Solution:

Specific gravity according to the local vendor: 0.5

Density of Natural Gas from Table 1: 0.0383 lb/ft

3

Maximum Temperature of the fuel going into the generator: 90°F

C=11111 (for Natural Gas) from Equation 1

F =

ٝ

—

p

e

ٝ

= 91,34 lb/hr

p = 0,0383 -

(90-60)

—

11111

p = 0,0356 lb/ft

3



Thus:

 =

91.34

—

0.0356

•

And:

 = 2566 ft

3

/hr

•

1.9.2 CALCULATING PIPE SIZE

Now that the volumetric flow rate has been identified, the minimum

pipe size can be determined by using Table 2. This table is based

on a specific gravity of 1.00 (specific gravity of air). For that

reason, a correction is required when the fuel used has a different

specific gravity. The fuel’s specific gravity can be obtained from

the fuel supplier. The table is also based on a pressure drop of

0.3, which allows for a nominal amount of restrictions from bends,

fittings, etc. Example 2 illustrates how to calculate the pipe size for

the generator.

Example 2: Determine the iron pipe size for a generator that

requires 2566 ft

3

/hr of Natural Gas. The unit is located 75 feet

from the fuel source.

Solution:

Specific gravity of natural gas according to the local vendor: 0.5

Multiplier for the given specific gravity from Table 1: 1.1

According to Table 2, a 2-1/2 inch pipe will deliver 1750 ft^3/hr

of air if it is located 75 feet from the fuel source. To determine the

volumetric flow rate of natural gas, multiply the given flow rate by

the multiplier (from Table 1).

Natural gas flow rate = air flow rate (ft

3

/hr) * Multiplier

= 1750 ft

3

/hr * 1.10

Natural gas flow rate = 1925 ft

3

/hr

Since the flow rate through a 2-1/2 inch iron pipe is less than the

flow rate required by the generator (2430 ft

3

/hr), we must evaluate

the next larger pipe (3 inches) by the same method.

Natural gas flow rate = air flow rate (ft

3

/hr) * Multiplier

= 3000 ft

3

/hr * 1.10

Natural gas flow rate = 3300 ft

3

/hr

A 3 inch pipe is required at the given distance of 75 feet. Pressure

drop does not have to be considered unless an unusual number

of fittings, bends or other restrictions are used. In such unusual

cases, the fuel supplier will usually specify which multiplier is

applicable.

NOTE:

The installed piping system shall be capable of providing the Fuel

Consumption requirements as identified in the specifications

section of the Owners Manual.

10

General Information

11

TABLE 1

Specific

Gravity(1)

Multiplier Density lb/ft

3

Specific

Gravity(1)

Multiplier Density lb/ft

3

Pressure Drop Multiplier

0.5 1.1 0.0383 1 0.775 0.0765 0.1 0.577

0.55 1.04 0.0421 1.2 0.707 0.0918 0.2 0.815

0.6 1 0.0459 1.4 0.655 0.1072 0.3 1

0.65 0.962 0.0497 1.5 0.633 0.1148 0.5 1.29

0.7 0.926 0.0536 1.7 0.594 0.1301 1 1.83

0.8 0.867 0.0612 1.9 0.565 0.1454 2 2.58

0.9 0.817 0.0689 2.1 0.535 0.1607 5 4.08

Note 1: Relative to air at 30 inches Hg, 60°F

TABLE 2

Length of Pipe

(In Feet)

Iron Pipe Size (IPS Inches)

1/2” 3/4” 1” 1-1/4” 1-1/2” 2” 2-1/2” 3” 4” 6” 8”

15 76 172 345 750 1220 2480 3850 6500 13880 38700 79000

30 52 120 241 535 850 1780 2750 4700 9700 27370 55850

45 43 99 199 435 700 1475 2300 3900 7900 23350 45600

60 38 86 173 380 610 1290 2000 3450 6800 19330 39500

75 77 155 345 545 1120 1750 3000 6000 17310 35300

90 70 141 310 490 1000 1560 2700 5500 15800 32250

105 65 131 285 450 920 1430 2450 5100 14620 29850

120 120 270 420 860 1340 2300 4800 13680 27920

150 109 242 380 780 1220 2090 4350 12240 25000

180 100 225 350 720 1120 1950 4000 11160 22800

210 92 205 320 660 1030 1780 3700 10330 21100

240 190 300 620 970 1680 3490 9600 19740

270 178 285 580 910 1580 3250 9000 18610

300 170 270 545 860 1490 3000 8500 17660

450 140 226 450 710 1230 2500 7000 14420

600 119 192 390 600 1030 2130 6000 12480

General Information

12

TABLE 3 — VAPOR CAPACITY OF PROPANE STORAGE TANKS

To Use: Go to the First column and pick the required kW load and then pick the minimum ambient temperature (40º, 20º or 0º F) that the

generator would be operating in. The third column (tank capacity) will give the required tank size to continually produce the given fuel flow.

Operating

Max kW Minimum Hours @ Tank Capacity Length Dia Overall

Vapor Temp Max kW (Gallons) Inches Inches Ht. Inches

30 40 24

20 20 35 120 57 24 33

10 0 67

35 40 26

25 20 36 150 68 24 33

12 0 72

60 40 26

40 20 38 250 94 30 39

20 0 74

80 40 26

50 20 40 325 119 30 39

25 0 77

100 40 31

60 20 51 500 119 37 46

30 0 100

150 40 35

100 20 53 850 165 41 50

50 0 105

170 40 36

120 20 51 1000 192 41 50

60 0 103

Propane storage tanks can provide either a liquid or a vapor supply to the generator. The above chart is for vapor withdrawal only and provides

the kW output or amount of vapor that can be withdrawn at a given temperature while keeping the temperature of the liquid above the boiling

point. If the withdrawal rate is too high, the LP temperature goes below the boiling point, the pressure drops to zero and no vapor can be with-

drawn. A primary regulator is also required at the tank to reduce the line pressure to the generator to 5-14 inches of water column.

Propane Conversions: 36.38 ft

3

= 90,500 btu = 1 gal • 1lb = 21,500 btu = 8.56 ft

3

Propane Storage Tank

General Information

13

1.10 ELECTRICAL CONNECTIONS

1.10.1 GROUNDING THE GENERATOR

A GROUNDING LUG is provided on the generator mounting base

for the purpose of grounding the frame and the external electrically

conductive parts of this equipment to an approved earth ground

and/or grounding rods where required by the National Electrical

Code (Figure 1.12). Consult a qualified electrician for grounding

requirements in the area. Grounding procedures must meet local

regulations.



Do not connect the ground wire to any pipe that

carries a flammable or explosive substance –

FIRE or an EXPLOSION may result.

Proper grounding helps protect personnel against electrical shock

in the event of a ground fault condition in the generator or in

connected electrical devices. In addition, grounding helps dissipate

static electricity that often builds up in ungrounded devices.

Figure 1.12 – Generator Grounding Lug (typical)

G

R

OU

NDIN

G

L

UG

1.10.2 BATTERY CHARGER CONNECTION

The generator has been equipped with a battery charger integrated

in the control panel. Power leads for the charger have been run to

the connection box (Figure 1.13). Connect the power leads for the

battery charger to the 120 VAC T1/LINE connection and the neutral

lead to the NEU connection. This is a 15 Amp circuit supplied by

the customer.

(Refer to the Connection Diagrams section in this manual, or the

wiring diagram in the Owner's Manual that is supplied with the

unit.)

Figure 1.13 — Battery Charger Connection

1.11 BATTERY INSTALLATION



Standby generators installed with automatic

transfer switches will crank and start

automatically when NORMAL (UTILITY) source

voltage is removed or is below an acceptable

preset level. To prevent such automatic start-

up and possible injury to personnel, do not

connect battery cables until certain that normal

source voltage at the transfer switch is correct

and the system is ready to be placed into

operation.



Storage batteries give off explosive hydrogen

gas. This gas can form an explosive mixture

around the battery for several hours after

charging. The slightest spark can ignite the gas

and cause an explosion. Such an explosion

can shatter the battery and cause blindness

or other injury. Any area that houses a storage

battery must be properly ventilated. Do not

allow smoking, open flame, sparks or any spark

producing tools or equipment near the battery.



Battery electrolyte fluid is an extremely caustic

sulfuric acid solution that can cause severe

burns. Do not permit fluid to contact eyes, skin,

clothing, painted surfaces, etc. Wear protective

goggles, protective clothing and gloves when

handling a battery. If fluid is spilled, flush the

affected area immediately with clear water.



Do not dispose of the battery in a fire. The

battery is capable of exploding.



Do not open or mutilate the battery. Released

electrolyte can be toxic and harmful to the skin

and eyes.

General Information

14



The battery represents a risk of high short

circuit current. When working on the battery,

always remove watches, rings or other metal

objects, and only use tools that have insulated

handles.

1.11.1 VENTED BATTERIES



The electrolyte is a dilute sulfuric acid that is

harmful to the skin and eyes. It is electrically

conductive and corrosive. The following

procedures are to be observed:

• Wear full eye protection and protective clothing,

• Where electrolyte contacts the skin, wash it off immediately

with water,

• Where electrolyte contacts the eyes, flush thoroughly and

immediately with water and seek medical attention, and

• Spilled electrolyte is to be washed down with an acid-

neutralizing agent. A common practice is to use a solution

of one pound (500 grams) bicarbonate of soda to one gallon

(4 liters) of water. The bicarbonate of soda solution is to be

added until the evidence of reaction (foaming) has ceased.

The resulting liquid is to be flushed with water and the area

dried.



Lead acid batteries present a risk of fire

because they generate hydrogen gas. The

following procedure are to be followed:

• DO NOT SMOKE when near batteries,

• DO NOT cause flame or spark in battery area, and

• Discharge static electricity from body before touching

batteries by first touching a grounded metal surface.

Servicing of batteries is to be performed or supervised by

personnel knowledgeable of batteries and the required precautions.

Keep unauthorized personnel away from batteries.

For recommended batteries, see the “Specifications” section in

the Owner’s Manual. All batteries must be at 100 percent state-of-

charge before they are installed on the generator.

When using maintenance-free batteries, it is not necessary to check

the specific gravity or electrolyte level. Have these procedures

performed at the intervals specified in the “Maintenance” section

in the Owner’s Manual. A negative ground system is used. Battery

connections are shown on the wiring diagrams. Make sure all

batteries are correctly connected and terminals are tight. Observe

battery polarity when connecting batteries to the generator set.

NOTE:

Damage will result if the battery connections are made in

reverse.

Before connecting the battery, make certain that normal utility

voltage at the transfer switch is correct and the system is ready to

be put into operation.

Check the engine oil, the coolant level, belt tension, and if so

equipped, the gearbox oil (Figure 1.14).

Figure 1.14 — Check Engine Oil

Check the battery to make sure it is fully charged before installing.

Follow all safety procedures detailed in the Owner’s Manual and

observe polarity when connecting the battery. Make sure all

terminal connections are tight (Figure 1.15).

Figure 1.15 — Check Terminal Connections

1.12 GENERATOR ACTIVATION

When battery power is applied to the generator during the

installation process, the controller will light up. However, the

generator still needs to be activated before it will automatically run

in the event of a power outage.

Activating the generator is a simple one time process that is guided

by the controller screen prompts. Once the product is activated,

the controller screen will not prompt you again, even if you

disconnect the generator battery.

After obtaining your activation code, please complete the following

steps at the generator’s control panel in the Activation Chart

(shown on the following page).

General Information

15

General Information

1.12.1 ACTIVATION CHART

CHOOSE LANGUAGE TROUBLESHOOTING

Display Reads: Use ARROW keys to scroll to desired language.

Press ENTER to select.

If the wrong language is chosen, it can be

changed later using the “edit” menu.

Display Reads: Press ENTER to begin the activation process. If ESCAPE is pressed instead of ENTER, your

generator will only run in manual mode (for

test purposes) and NOT ACTIVATED will be dis-

played. You will need to remove the generator

control panel fuse AND disconnect the T1, N1,

N2 connector in the external connection box (if

equipped) or disconnect the utility input (main

breaker) to the transfer switch for 3-5 seconds.

Reconnect and start over with step 1.

Display Reads: If you do not have your activation code, go to

www.activategen.com or call 1-888-9ACTIVATE

(922-8482).

If you already have your activation code, wait 3-5

seconds for the next display.

ENTER ACTIVATION CODE (Passcode) TROUBLESHOOTING

Display Reads: Use ARROW keys to scroll and find the first num-

ber of your Activation Code.

Press ENTER to select.

Repeat this step until all digits have been entered.

Use ESCAPE to correct previous digits.

Display Reads: Activation is complete when all digits are entered

above and your screen shows this display.

Follow the controller prompts to continue setting

the time function. Refer to your Owner’s Manual

with questions.

What happens if “Wrong Passcode Try Again”

appears?

Reenter the activation code. If a second attempt

is unsuccessful, check the number against the

code given on activategen.com. If it is correct

and the generator will not accept it, contact

1-888-9ACTIVATE (922-8482).

“SELECT HOUR (0-23)”

“- +”6

Escape Enter

Serial 123456789

Passcode XXXXX +/-

Escape Enter

To Activate go to

www.activategen.com

Escape Enter

Activate me (ENT) or

ESC to run in manual

Escape Enter

Language

- English +

Escape Enter

16

2.1 TRANSFER SWITCH

The generator system should be used in conjunction with a

matched automatic transfer switch. The NEMA 3R enclosure is

weather proof and can be used indoors or outdoors.

2.2 UNPACKING

Carefully unpack the transfer switch. Inspect closely for any

damage that might have occurred during shipment. The purchaser

must file with the carrier any claims for loss or damage incurred

while in transit.

Check that all packing material is completely removed from the

switch prior to installation.

Attach any lifting device to the transfer switch mounting holes or

brackets only. DO NOT LIFT THE SWITCH AT ANY OTHER POINT.

Always inspect the transfer switch for shipping damage.

2.3 MOUNTING

Mounting dimensions for the transfer switch enclosure can be

found in the transfer switch owner’s manual. Enclosures are

typically wall-mounted.

The transfer switch must be mounted vertically and must be level

and plumb.



Handle transfer switches carefully when

installing. Do not drop the switch. Protect the

switch against impact at all times, and against

construction grit and metal chips. Never install

a transfer switch that has been damaged.

Install the transfer switch as close as possible to the electrical

loads that are to be connected to it. Mount the switch vertically

to a rigid supporting structure. To prevent switch distortion, level

all mounting points. If necessary, use washers behind mounting

holes to level the unit. Never install the switch where water or any

corrosive substance might drip into the enclosure.

RTS and HTS switches are open transition switches. Because load

circuits can only be connected to one power supply at a time,

open transition switches prevent electrical feedback between utility

circuits and generator circuits (Figure 2.1).

Figure 2.1 — Connect Power Leads

3.1 BASIC STANDBY ELECTRIC

SYSTEM

Figure 3.1 shows a schematic diagram of a basic standby

electric system. Both the UTILITY power supply and the STANDBY

(GENERATOR) output are connected to an approved transfer

switch. The transfer switch is required by electrical code and

serves the following functions:

• Allows the LOAD circuits to be connected to only one power

supply at a time.

• Prevents electrical backfeed between the generator and the

UTILITY power circuits.

Figure 3.1 – Basic Standby Electric System

Notice that both the STANDBY and the UTILITY power supplies to

the transfer switch are protected against overload by a main line

circuit breaker.

3.2 STANDBY CIRCUIT ISOLATION

METHOD

This prevents overloading the generator by keeping electrical

loads below the wattage/amperage capacity of the generator. If the

generator is powering only designated loads, within the wattage/

amperage capacity, during utility power outages, consider using

the emergency circuit isolation method.

Designated electrical loads are grouped together and wired into

a separate “Standby Distribution Panel.” Load circuits powered

by that panel are within the wattage/amperage capacity of the

generator set. When this method is used, it is difficult to overload

the generator. The transfer switch must meet the following

requirements:

• It must have an ampere rating equal to the total amperage rating

of the standby distribution panel circuit.

• Have it installed between the building’s main distribution panel

and the standby distribution panel.

Installation

17

The generator powers only designated loads that are grouped

together and wired into a separate emergency distribution panel.

The transfer switch is installed between the main distribution panel

(A) and the emergency distribution panel (E) (Figure 3.1).

The amperage rating of the transfer switch must be equal to,

or greater than, the highest amperage rating of the utility and

generator breakers feeding the switch.

Figure 3.1 — Standby Isolation

3.3 TOTAL CIRCUIT ISOLATION

METHOD

When a generator capable of powering all electrical loads in the

circuit is to be installed, use the “Total Circuit Isolation Method.” It

is possible for the generator to be overloaded when this isolation

method is employed. The following apply to the transfer switch in

this type of system.

• Ampere rating of the transfer switch must equal the ampere

rating of the normal incoming utility service.

• The transfer switch is installed between the utility service

entrance and the building distribution panel.

The generator will be backing up all electrical loads within the

circuit, so the amperage rating of the transfer switch must be

equal to, or greater than, the amperage rating of the normal utility

service.

Unless a service entrance rated transfer switch is used, a main

service disconnect (D) must be located before the transfer switch.

The transfer switch is installed between the utility service entrance

and the building distribution panel (A) (Figure 3.2).

Figure 3.2 — Total Circuit Isolation

3.4 ALL TRANSFER SWITCH

INSTALLATIONS

Power wiring, control wiring and wiring for the 15 or 20 Amp

circuit required for the 2-Amp smart charger should be in separate

conduit.

In all installations, a ground wire will run through the power conduit

from the generator connection panel to the transfer switch (Figure

3.3).

Figure 3.3 — Ground Wire

In any three-phase application, the phase rotation of the generator

power lines must match the phase rotation of the utility power lines

at the transfer switch (Figure 3.4).

A

E

ATS

D

A

ATS

Operation

18

Figure 3.4 — Match Phase Rotation

While supporting the lugs, use a torque wrench to tighten the lugs

on the generator circuit breaker and the transfer switch. Torque

specifications are in the Transfer Switch Owner’s Manual (Figure

3.5).

Consult the Technical Manual that comes with the transfer switch

for wiring diagrams and any product changes, modifications or

updates.

Figure 3.5 — Torque Lugs

3.5 NEXUS TRANSFER SWITCHES

Generators equipped with the Nexus Digital Controller will be

matched to a Nexus or RTS transfer switch.

N = Normal Utility Supply

E = Generator Connection Panel

T = Load Distribution Panel

When installing these switches, terminals 178 and 183 (2-wire

start) are not used.

3.6 CONNECTION DIAGRAMS

All wiring in the standby electric power system must be in strict

compliance with applicable codes, standards and regulations.

Such wiring must be properly supported, routed, and connected.

In addition, wiring must be properly sized to carry the maximum

load current to which is will be subjected.

The connections between the generator and transfer switch will

vary depending on the equipment ordered. In each case there are

two types of interconnections, load wiring and control wiring.



Make sure to turn OFF both the NORMAL

(UTILITY) and STANDBY (EMERGENCY) power

supplies before trying to connect power source

and load lines to the transfer switch. Supply

voltages are extremely high and dangerous.

Contact with such high voltage power supply

lines causes extremely hazardous, possibly

lethal, electrical shock.



Be sure to maintain proper electrical

clearances between live electrical parts and

grounded metal. Allow at least one-half inch of

clearance circuits up to 400 amps.



Extremely high and potentially lethal supply

voltages are present at the transfer switch when

verifying phase rotation. This operation should

only be performed by a trained electrician.

3.6.1 NEXUS CONTROLLER TO A RTS/NEXUS SMART

SWITCH

The Nexus controller generator consists of an AUTO/OFF/

MANUAL switch and a 2-line LCD display. See Figure 3.6 for an

interconnection diagram. See "Control Wiring" for control wire

sizing recommendations.



Make sure to turn OFF the NORMAL (UTILITY)

power supply before trying to connect the Utility

1 and Utility 2 control wires. Supply voltages

are extremely high and dangerous. Contact with

such high voltage power supply lines causes

extremely hazardous, possibly lethal, electrical

shock.



Terminals 178 and 183 in the generator AC

connection box are not used in this application.

Connection of any wires to these terminals may

result in unwarrantable damage to the control

board.

Operation

Страница загружается ...

Generac 70kW QT07068AVAC Руководство пользователя

Generac 70kW QT07068AVAC Руководство пользователя

на других языках