Zigmund & Shtain MN 135.61 I Руководство пользователя

USER MANUAL

РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ

GN 238.451 S,B,W

GN 238.61 S,X,B,W

GN 238.31.S

GN 228.61 S,B,W

MN 135.61 B

2

Dear User,

Our objective is to make this product provide you with the best output

which is manufactured in our modern facilities in a careful working

environment, in compliance with total quality concept.

Therefore, we suggest you to read the user manual carefully before

using the product and, keep it permanently at your disposal.

Note: This user manual is prepared for more than one model. Some

of the features specied in the Manual may not be available in your

appliance.

All our appliances are only for domestic use, not for commercial use.

“Conforms with the WEEE Regulations.”

GB

3

CONTENTS

Important Warnings

4

Introduction Of The Appliance

6

Control Panel

7

Electrical Connection Scheme

7

Important Warnings

8

If Built-In Oven Is Placed Under Cooktop

10

Installation Of Cookstop

10

Counter Cutting Sizes And Installation Of Your Cooktop

12

Correct Place For Installation

13

Ventilation Of Room

13

Transformation From Natural Gas To Lpg And

From Lpg To Natural Gas

14

Gas Breaking Safety Appliance (FFD)

14

Usage Of Your Cooktop

15

Pot Diameter 16

Wok Burner 17

Usage Of Hotplate 17

Maintenance And Cleaning

18

Troubles And Solution Proposals

19

Setting Gas Cooktops As Per Gas Type 19

Injector, Gas Flow And Power Table 20

Environmentally-Friendly Disposal And

Package Information

21

GB

4

IMPORTANT WARNINGS

1. WARNING: Before touching the connection terminals,

all supply circuit should be disconnected.

2. WARNING: Any inadvertent cooking made with fats and

oils can be dangerous and cause re.

3. WARNING: Risk of re; do not store the food materials

on the cooking surface.

4. WARNING: During usage the reachable sections can

be hot. Keep the small children away.

5. WARNING: The appliance and its reachable sections

become hot during usage.

6. The setting conditions of this appliance is indicat-

ed on the label. (Or data tag)

7. This appliance is not connected to a combustion prod-

uct discharge system.This appliance shall be connected

and installed as per the applicable installation legislation.

Consider the requirements related with ventilation.

8. Using a gas hob will release humidity and combus-

tion products in the room where it resides. Especially

during when the appliance in use, ensure that the kitch-

en is well ventilated and retain the natural ventilation

holes or install a mechanical ventilation system. (Hood

on top of the oven) Sustained usage of the appliance

may require additional ventilation. For example open-

ing a window or if available, increasing the ventilation

level of a mechanical ventilation system.

9. WARNING: The appliance is intended for cooking only.

It must not be used for other purposes like room heating.

GB

5

10. This appliance should be installed as per regula-

tions and in well-ventilated location only. Read the in-

structions before installing or operating the appliance.”

11. Before placing the appliance check the local

conditions (gas type and gas pressure) and ensure

that the settings of the appliance is appropriate.

12. These instructions are applicable for countries of

which symbols are indicated on the appliance. If the

country symbol is not available on the appliance, in

order to adapt the appliance to the conditions of such

country, the technical instructions should be read.”

13. Do not operate the system for more that 15

seconds. If the burner does not ignite at the end of

15 seconds stop the operation of the system and open

the section door and/or wait for at least 1 minute

before igniting the burner.

14. Do not use steam cleaners to clean the appliance.

15. NEVER try to extinguish a re with water, rst

disconnect the mains supply and then using, for

example a lid or blanket, cover the re.

16. Unless continuous supervision is provided, the

children of age 8 or below should be kept away.

17. Pay attention for not to touch the heating elements.

18. This appliance can be used by children aged

from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given su-

pervision or instruction concerning use of the appliance

in a safe way and understand the hazards involved.

GB

6

INTRODUCTION OF THE APPLIANCE

1 - Burner positions

2- Glass or Metal Surface

3- Control Buttons

4- Small Burner

5- Medium Burner

6- Large Burner

7 - WOK Burner

8- Hotplate

9- Coffee Adaptor

10-Wok Burner Adaptor

11- Cast Grill

12- Enamel Grill

1

2

3

8

4 5 6 7

12

11

9 10

GB

7

CONTROL PANEL

ELECTRICAL CONNECTION SCHEME

Get electrical connection of your appliance done to authorized person in

line with the following scheme.

Cooktop Panel Visual of 70-90 cm and 100 cm

Cooktop Panel Visual of 60 cm

Cooktop Panel Visual of 45 cm

Cooktop Panel Visual of 30 cm

L1

220-240V~50/60Hz

H05 VV-F 3G 1.5mm²

Earth

Terre

Erdung

Neutral

Neutre

GB

8

IMPORTANT WARNINGS

Electrical Connection and Safety

1.Setting conditions of this appliance is indicated in tag or data plate.

2.This appliance is not connected to any discharging apparatus of burn-

ing products. It should be connected and installed according to applica-

ble assembly regulation.

3.Great attention should be paid on ventilation related conditions.

4.Your appliance should be connected to an appropriate fuse according to

electric power. If necessary, it is recommended that connection is made by

authorized service.

5.Your appliance is congured in accordance with electrical supply of

220-240V, 50/60Hz.

6.If main electrical network is different from these values, contact with

your authorized service.

7.Electrical connections of your appliance should only be made to the

fuses having suitably wired grounding (grounded) system. If no conven-

ient fuse is available in the place where your appliance is to be installed,

contact with authorized service immediately. Manufacturing rm is not

responsible denitely for the damages that fuses whose grounding is not

made and connected to the appliance can cause.

8.Plug of the appliance should be close to be accessed easily to the fuse

whose grounding is made without use of extension cord.

9.Do not allow contacting the power cable of your appliance with hot

regions. Similarly, keep away it from sharp edges and corners.

10.If feeder cord is damaged, this cord should be replaced either by

manufacturer or its service agency or same degree qualied personnel in

order to hinder a dangerous situation.

11.Wrong electrical connection may give damage to the appliance. In

this case, your appliance will remain out of guarantee scope. Electrical

connection of your appliance should be done by authorized service.

12.During operation of cooktop, some parts may be hot. When you also

bring switches closed position, it may remain hot for a while. Children

should be kept away every time and not be left without observation. Do

not touch surface of cooktop while warning lights ashes. When you bring

your appliance closed position, hot parts being still dangerous are stated

with warning lights. (Vitroceran models).

GB

9

Gas Connection and Safety

1. For LPG (cylinder) connection, afx

metal clamp on the hose coming from

LPG cylinder. Afx an edge of the hose on

hose inlet connector behind the appliance

by pushing to end through heating the

hose in boiled water. Afterward, bring the

clamp towards end section of the hose and

tighten it with screwdriver. The gasket and

hose inlet connector required for connec-

tion is as the picture shown below.

NOTE: The regulator to be afxed on LPG cylinder should have 300

mmSS feature.

2. Natural gas connection should be

done by authorized service. For natural

gas connection, place gasket in the nut

at the edge of natural gas connection

hose. To install the hose on main gas

pipe, turn the nut. Complete the con-

nection by making gas leakage control.

Gas hose and electric connection of the appliance should

not pass next to hot areas such as back of the appliance.

Gas hose should be connected by making wide angle turns

against breaking possibility. Movement of appliance whose

gas connection is made may cause gas leakage.

Main Gas Pipe

Gasket

Hose Inlet Connector

Metal Clamp

Lpg Connection Hose

Main Gas Pipe

Gasket

Nut

Natural Gas Connection Hose

True False True True

GB

10

3. Connect your appliance to gas cock from the shortest way and in

a manner to prevent any leakage. For safety, the hose used should be

maximum 125 cm and minimum 40 cm.

4. While making gas leakage control; never use lighter, match, glowing

cigarette or similar inammable matter.

5. Apply soap bubble on connection point. If any leak/leakage exists,

foaming will occur on soaped region.

6. If the cooktop is to be mounted on a cabinet or openable drawer,

a heat protection panel having 15 mm minimum opening should be

mounted under the cooktop.

IF BUILT-IN OVEN IS PLACED UNDER COOKTOP;

Gas pipe should be afxed in a way not to touch the oven below, sharp

edges and corners, not to be pulled in a manner to be twisted and

strained. Make gas connection from right part of the cooktop, fasten the

hose by use of clamp.

INSTALLATION OF COOKSTOP

1. Detach the burners, burner hoods and grills from the product.

2. Turn the cooktop down and place on smooth ground.

3. In order to prevent entrance of foreign substances and liquids be-

tween cooktop and counter, apply the paste given in package to the sides

of lower guard of counter. For corners, curl paste and increase curls till

lling corner gaps.

4. Turn cooktop again and align with and place on counter.

5. Fasten up your cooktop on counter by using the clamp and screws

supplied.

On the assembly chart given in next page, it is shown how to assemble

your cooktop.

Cooktop

Hose

Oven

Figure 1

GB

11

6. When product is mounted on a drawer, if it is possible to touch lower

side of product, this section should be separated with a wooden shelf.

7. While mounting cooktop on a closet, as shown in the gure above, in

order to separate between closet and cooktop, a shelf should be mounted.

If it is mounted on a built-in oven, there is no need to do that.

8. If your cooktop will be mounted next to right or left wall, the

minimum distance between wall and cooktop should be 50 mm.

Roving

Figure 2

min. 30 cm

Figure 3

GB

12

COUNTER CUTTING SIZES AND INSTALLATION OF YOUR COOKTOP

Pay attention to the drawings and dimensions given below while making

cooktop installation and adjusting counter cutting sizes.

Cooktop Of 30cm

300 mm

520 mm

490 mm

270 mm

min. 60 mm

Cooktop Of 45cm

520 mm

490 mm

440 mm

410 mm

min. 60 mm

Cooktop Of 60cm

520 mm

490 mm

590 mm

560 mm

min. 60 mm

Cooktop Of 90cm

520 mm

490 mm

860 mm

810 mm

min. 60 mm

Cooktop Of 100cm

400 mm

370 mm

990 mm

960 mm

min. 60 mm

Cooktop Of 70cm

690 mm

520 mm

560 mm

490 mm

min. 110 mm

min. 60 mm

GB

13

CORRECT PLACE FOR INSTALLATION

Product is designed in

accordance with the kitch-

en counters supplied from

market. A safe distance

should be left between the

product and kitchen walls

and furniture.

If hood/aspirator will be in-

stalled over your appliance,

obey to the recommen-

dation of hood/aspirator

manufacturer for assembly

height. (min. 65 cm)

The gap that cooktop is to

be placed on the counter

should be cut in line with

cooktop installation dimen-

sions.

For installation of the product, the rules specied in local standards

related to electricity should be complied.

VENTILATION OF ROOM

The air needed for burning is received from room air and the gases

emitted are given directly in room. For safe operation of your product,

good room ventilation is a precondition. If no window or room to be

utilized for room ventilation is available, additional ventilation should be

installed. However, room has a door opening outside, it is no needed to

vent holes.

650 mm min.

Room Size Ventilating Opening

Smaller than 5m³ min. 100 cm²

Between 5 m³- 10m³ min. 50 cm²

Bigger than 10m³ no need

In basement or cellar min. 65 cm²

GB

14

TRANSFORMATION FROM NATURAL GAS TO LPG AND FROM LPG TO NATURAL GAS

1. Turn off gas and electricity of the cooktop. If your cooktop is hot, wait

for cooling down.

2.For injector change, use a screwdriver whose edge is as the Figure 4.

3. As seen in Figure 5, demount burner lid and burner of the cooktop

and ensure visibility of injector.

4. Remove injector by turning as shown in Figure 6 with screwdriver and

replace it with a new one.

5. After that, detach control switches of the cooktop. Make setting by

turning the screw in the middle of gas cocks with a small screwdriver

in the manner shown in the following picture. To adjust ow rate screw,

use a screwdriver having suitable dimension. For LPG, turn the screw

clockwise. For natural gas, turn the screw one time counter clockwise.

At low position, length of normal ame should be 6-7 mm. For the last

control, check out whether ame is open or closed.

Setting of your appliance may differ according to the type of gas cock

used.

GAS BREAKING SAFETY APPLİANCE (FFD)

Against putting out to be taken place as a

result of liquid overow at upper burners, safety

appliance steps in and cut gas immediately.

Figure 4 Figure 5 Figure 6

Figure 7 Figure 8

Figure 9

FFD

GB

15

USAGE OF YOUR COOKTOP

Usage of Gas Cooktop

1. Before starting to use your cooktop, be sure burner hoods are at

correct position. Correct placement of burner hoods are shown in the

following gure.

2. Gas cocks have a special locking mechanism. Therefore, to operate

cooktop zone, press button by pushing ahead and while opening or clos-

ing the cock, hold down the button.

Closed Fully open Half open

3. For automatic igniting models, igniting is realized via electricity.

Therefore, before operating appliance, be sure that appliance has electric

connection. Igniting for these models is as follows.

4. Pay attention that cooktop grills are placed on cooktop table

completely. In case of failure about this matter can cause pouring of the

materials to be put on that.

5. For the models having gas putting out safety, following realizing

ignition procedure according to the guidelines above, wait for 5-10

seconds by pushing button ahead without keeping your hands off. Safety

Figure 10 Figure 11

Cooktop cock

is at closed

position.

To ignite cook-

top, rstly press

the button

towards ahead.

While hold-

ing down the

button, lighter

steps in and

starts to

ignition.

By turning the

button right while

holding down,

you can provide

ignition at ame

length you want.

GB

16

mechanism will step in this duration and ensures operation of the cook-

top. With regard to gas putting out appliance, gas cock cuts the gas going

to cooktop zone in case of putting out of cooktop ame due to any reason.

6. While using coffee pot apparatus supplied along with the cooktop, be

sure that foots of apparatus are placed on cooktop grill exactly and remain

on cooktop zone in centred way. Use the apparatus only on small burner.

7. While utilizing gas cooktops, use saucepan, placed on cooktop sur-

face as far as possible. Thanks to that, you can save energy. In the follow-

ing table, cooking pot diameters recommended to be used as per burners

are given. Characteristic of Wok cooktop zone is to cook quickly.

POT DIAMETER

GLASS HOBS

Domino

45cm.

Hobs

60cm.

Hand

Control

60cm.

Control

Front

70cm.

Control

Front

90cm.

Control

Front

Small Burner 12-18cm 12-18cm 12-18cm 12-18cm 12-18cm 12-18cm

Middle Burner --- 18-20cm 18-20cm 18-20cm 18-20cm 18-22cm

Big Burner 18-24cm 22-24cm 22-24cm 22-24cm 22-24cm 22-26cm

Wok Burner 24-26cm --- 24-26cm 24-26cm 24-26cm 26-30cm

METAL HOBS

Domino

45cm.

Hobs

60cm.

Hand

Control

60cm.

Control

Front

70cm.

Control

Front

90cm.

Control

Front

Small Burner 12-18cm 12-18cm 12-18cm 12-18cm 12-18cm 12-18cm

Middle Burner --- 18-20cm 18-20cm 18-20cm 18-20cm 18-22cm

Big Burner 18-22cm 22-24cm 22-26cm 22-24cm 22-24cm 22-26cm

Wok Burner 24-26cm 24-26cm 24-26cm 24-26cm 24-26cm 26-32cm

Cooking pot to be used with products should have minimum 120 mm. diameter.

False TrueFalseFalse

GB

17

WOK BURNER

As it possesses double ring ame system, it gives

homogenous heat distribution at the bottom of

cooking pot at high temperature. It is ideal for

short term and high temperature cooking. When

you want to use regular cooking pot on wok burner,

it is necessary that you remove wok cooking pot

carrier from cooktop.

USAGE OF HOTPLATE

You can operate electric cooktops by turning the button on control panel

you want to use to the level you desire. Cooktop powers as per levels are

given in the following table.

LEVEL 1 LEVEL 2 LEVEL 3 LEVEL 4 LEVEL 5 LEVEL 6

Ø80mm

200W 250W 450W --- --- ---

Ø145mm

250W 750W 1000W --- --- ---

Ø180mm

500W 750W 1500W --- --- ---

Ø145mm Rapid

500W 1000W 1500W --- --- ---

Ø180mm Rapid

850W 1150W 2000W --- --- ---

Ø145mm

95W 155W 250W 400W 750W 1000W

Ø180mm

115W 175W 250W 600W 850W 1500W

Ø145mm Rapid

135W 165W 250W 500W 750W 1500W

Ø180mm Rapid

175W 220W 300W 850W 1150W 2000W

Figure 12

GB

18

MAINTENANCE AND CLEANING

Before starting to maintenance or cleaning, rstly unplug the plug

supplying electricity to cooktop and turn off gas valve. If cooktop is hot,

wait for cooling down.

1. For the purpose that your cooktop has long and economic life, regular

cleaning and maintenance should be performed on your cooktop.

2. Do not clean your cooktop with scratching tools such as bristle

brush, wire wool or knife. Do not use abrasive, scratching, acid materials

or detergent.

3. Following mopping parts of your cooktop with soapy cloth, rinse it,

later rinse well with a soft cloth.

4. Clean glass surfaces with special glass cleaning substances. As

scratching of glass surfaces leads to breaking, while cleaning glass

surfaces, do not use abrasive cleaners or sharp metal scrapers.

5. Do not clean your cooktop with steamy cleaners.

6. Clean channels and lids of cooktop zones with soapy water and clean

gas channels with a brush.

7. In the course of cleaning your cooktop, never use ammable materials

such as acid, thinner and gas.

8. Do not wash plastic and aluminium parts of your cooktop in

dishwasher.

9. Clean vinegar, lemon, salt, coke and similar acid and alkaline

containing substances poured on your cooktop immediately.

10. In time, cooktop buttons turns hard or never turn any more, in

such circumstances, it may be necessary that buttons are changed. The

change should only be done by authorized service.

Figure 13 Figure 14

Figure 15

GB

19

TROUBLES AND SOLUTION PROPOSALS

You can solve the troubles you can encounter at your product by checking

the following points before calling technical service.

If cooktop does not operate;

• Check if power cable of cooktop is plugged in

• Examine with safe ways if electric exists on network

• Audit fuses.

• Control whether damage is available on power cable.

• Check if main gas valve in your network is open

• Go through existence of breaking or twisting on gas pipe

• Be sure that gasp pipe is connected to cooktop in appropriate way.

• See over if suitable gas valve is used for your cooktop

(Get periodical maintenance done.)

If starter does not operate;

• Be sure that electric power cable of product is plugged in

• Clean the edge and body sections of ignition spark plugs found on

burners with a wet and dirt remover materials thoroughly. Be sure that the

channels present on burners are open and clean.

SETTING GAS COOKTOPS AS PER GAS TYPE

Gas type (LPG or natural gas) that your appliance is manufactured

foris stated in the label found behind the product and that show

technical features. If gas setting of your appliance is not the same as

gas setting of your network, it should be adjusted by making change by

an expert person. In the following table, injector, gas ow and power

values of appliance is given according to gas type.

GB

20

INJECTOR, GAS FLOW And POWER TABLE

BURNER

SPECIFICATIONS

G20,20 mbar

G25,25 mbar

G20,25 mbar G20,13 mbar

Gas Natural Gas Natural Gas Natural

Wok

Burner

Injector 1,40 mm 1,28 mm 1,60 mm

Gas Flow 0,333 m³/h 0,333 m³/h 0,333 m³/h

Power 3,50 kW 3,50 kW 3,50 kW

Rapid

Burner

Injector 1,15 mm 1,10 mm 1,45 mm

Gas Flow 0,276 m³/h 0,276 m³/h 0,276 m³/h

Power 2,90 kW 2,90 kW 2,90 kW

Semi-Rapid

Burner

Injector 0,97 mm 0,92 mm 1,10 mm

Gas Flow 0,162 m³/h 0,162 m³/h 0,162 m³/h

Power 1,70 kW 1,70 kW 1,70 kW

Auxiliary

Burner

Injector 0,72 mm 0,70 mm 0,85 mm

Gas Flow 0,96 m³/h 0,96 m³/h 0,96 m³/h

Power 0,95 kW 0,95 kW 0,95 kW

INJECTOR, GAS FLOW And POWER TABLE

BURNER

SPECIFICATIONS

G30,28-30 mbar

G31,37 mbar

G30,50 mbar G30,37 mbar

LPG LPG LPG

Wok

Burner

Injector 0,96 mm 0,76 mm 0,96 mm

Gas Flow 254 g/h 254 g/h 254 g/h

Power 3,50 kW 3,50 kW 3,50 kW

Rapid

Burner

Injector 0,85 mm 0,75 mm 0,85 mm

Gas Flow 211 g/h 211 g/h 211 g/h

Power 2,90 kW 2,90 kW 2,90 kW

Semi-Rapid

Burner

Injector 0,65 mm 0,60 mm 0,65 mm

Gas Flow 124 g/h 124 g/h 124 g/h

Power 1,70 kW 1,70 kW 1,70 kW

Auxiliary

Burner

Injector 0,50 mm 0,43 mm 0,50 mm

Gas Flow 69 g/h 69 g/h 69 g/h

Power 0,95 kW 0,95 kW 0,95 kW

GB

Страница загружается ...

Zigmund & Shtain MN 135.61 I Руководство пользователя

Zigmund & Shtain MN 135.61 I Руководство пользователя

на других языках

Похожие модели бренда