Sony KV-HG21 Руководство пользователя

Категория
Телевизоры CRT
Тип
Руководство пользователя

Это руководство также подходит для

Tr initron Color TV
© 2007 Sony Corporation
KV-HG21
3-213-968-E1 (1)
Operating Instructions
Before operating the unit, please read this manual thoroughly and retain
it for future reference.
GB
M91
110-240 V AC, 50/60 Hz
Indicated on the rear of the TV
B/G, I, D/K, M
PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43
NICAM Stereo/Bilingual B/G, I, D/K;
A2 Stereo/Bilingual B/G
English, Russian
VHF : E2 to E12 /UHF : E21 to E69 /
CATV : S01 to S03, S1 to S41
UHF : B21 to B68 /CATV : S01 to S03, S1 to S41
VHF : C1 to C12, R1 to R12 /
UHF : C13 to C57, R21 to R60 /
CATV : S01 to S03, S1 to S41, Z1 to Z39
VHF : A2 to A13 /UHF : A14 to A79 /
CATV : A-8 to A-2, A to W+4, W+6 to W+84
75-ohm external terminal
5 W + 5 W
Input: 2 Output: 1 Phono jacks; 1 Vp-p, 75 ohms
Input: 3 Output: 1 Phono jacks; 500 mVrms
Input: 1 Phono jacks;
Y: 1 Vp-p, 75 ohms,
sync negative
C
B: 0.7 Vp-p, 75 ohms
C
R: 0.7 Vp-p, 75 ohms
Output: 1 Stereo minijack
87.5 - 108.0 MHz
10.7 MHz
21 in.
54
Measured diagonally
51
Measured diagonally
638 × 458 × 482
25
A Specifications
KV-HG21M91 Note
Design and specifications are subject to change without notice.
Made in Malaysia.
Manufacturer: Sony Corporation
Address: 1-7-1 Konan, Minota-ku,
Tokyo 108-0075, Japan.
Power requirements
Power consumption (W)
Television system
Color system
Stereo/Bilingual system
Teletext language
Channel coverage
B/G
I
D/K
M
8 (Antenna)
Audio output (Speaker)
Number of terminal
(Video)
(Audio)
(Component
Video)
i (Headphone)
FM Radio
Tuning Range
Intermediate
Frequency
Picture tube
Tube size (cm)
Screen size (cm)
Dimensions (w/h/d, mm)
Mass (kg)
Clean the TV with a dry and soft
cloth. Do not use benzine, thinner,
or any other chemicals to clean the
TV. Do not attach anything (e.g.,
adhesive tape, cellophane tape,
glue) on the painted cabinet of the
TV. Do not scratch the picture
tube.
B WARNING
• Dangerously high voltages are present inside the TV.
• TV operating voltage: 110 – 240 V AC.
Do not plug in the power cord until you have completed making all other
connections; otherwise a minimum leakage current might flow through the antenna
and other terminals to ground.
•To avoid battery leakage and damage to the remote, remove the batteries from the
remote if you are not going to use it for several days. If any liquid leaks from the
batteries and touches your skin, immediately wash it away with water.
Install the TV on a stable TV stand
and floor which can support the
TV set weight. Ensure that the TV
stand surface is flat and its area is
larger than the bottom area of the
TV.
Do not plug in too many
appliances to the same power
socket. Do not damage the power
cord.
For children’s safety, do not leave
children alone with the TV. Do not
allow children to climb onto it.
For your own safety, do not touch
any part of the TV, the power cord
and the antenna cable during
lightning storms.
Do not place any objects on the TV.
The apparatus shall not be
exposed to dripping or splashing
and that no objects filled with
liquids, such as vases, shall be
placed on the apparatus.
Do not operate the TV if any liquid
or solid object falls into it. Have it
checked immediately by qualified
personnel only.
Do not block the ventilation
openings of the TV. Do not install
the TV in a confined space, such
as a bookcase or built-in cabinet.
Do not open the cabinet and the
rear cover of the TV as high
voltages and other hazards are
present inside the TV. Refer
servicing and disposal of the TV
to qualified personnel.
Pull the power cord out by the
plug. Do not pull the power cord
itself. Even if your TV is turned
off, it is still connected to the AC
power source (mains) as long as
the power cord is plugged in.
Unplug the TV before moving it
or if you are not going to use it for
several days.
To prevent fire or shock hazard, do
not expose the TV to rain or
moisture.
Your TV is recommended for
home use only. Do not use the TV
in any vehicle or where it may be
subject to excessive dust, heat,
moisture or vibrations.
b
1
C Getting Started
Connect the antenna cable (not supplied) to 8
(antenna input) at the rear of the TV.
•Your TV can receive both TV and FM radio signals from
the appropriate connections through the 8 (antenna
input) terminal (see E).
•You can also connect your TV to other optional
components (see E).
Step 2
Insert the batteries (supplied) into the remote.
Do not use old or different types of batteries together.
Step 1
Set up the TV by following the instructions of the
Начальная настройкa” (“Initial Setup”) menu
(see D).
Step 4
Plug in the power cord, then press 1 on the TV to
turn it on.
The 1 (standby) indicator flashes green for a few
seconds when turning on the TV. This does not indicate
a malfunction.
Step 3
D
Setting up your TV (“Initial Setup”)
When you turn on your TV for the first time, the “Initial Setup” menu will
appear. You can adjust settings below using the buttons on the remote control
or TV front panel. Press V , v , B or b to select or adjust items, then press
.
1
Select the desired menu language.
2
Select “Yes” to preset the channels automatically.
To skip automatic channel presetting, select “No”.
3
The “Program Sorting/Edit” menu enables
you to sort and edit the channels (see L).
4
Adjust the bars on the top and bottom of the menu
if they are slanted.
5
To prevent this “Initial Setup” menu from appearing
again when you turn on the TV by pressing 1,
select “No”.
To allow this menu to appear again, select “Yes”.
•You can immediately go to the end of the “Initial Setup” menu by pressing WEGA
GATE.
Program Sorting/Edit
01
02
03
04
Off
Off
Off
Off
Sorting:
Edit:
PROG
SkipLabel
Exit
Select
Confirm
End
Select
Confirm
Start Auto Program now?
Yes
No
First please connect
cable/ antenna
Initial Setup
End
Select
Confirm
Select
Confirm
Initial Setup
Display this menu next time?
Yes
No
End
Select
Confirm
FM
E Connecting optional components
You can connect a wide range of optional components to your TV. Connecting
cables are not supplied.
Connecting to the TV (front)
Connecting to the TV (rear)
Camcorder
Audio/Video
cable
Headphones
Y
R
L
CB
CR
R
L
R
L
RL
Y
R
L
CB
CR
R
L
1
L
(MONO)
R
L
(MONO)
R
Y
C
R
C
B
If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the
program number 0 on the TV (see L).
If your DVD player can output interlace and progressive mode signals, select the
interlace output when connecting to (component video input) on your TV. Your TV
can receive either 525i/60Hz or 625i/50Hz interlace signals.
The component video terminals on your DVD player are sometimes labeled Y/CB/CR,
Y/PB/PR, Y/Cb/Cr or Y/B-Y/R-Y.
If you select “DVD” on your TV screen, the signal from the T (monitor output) jacks
will not be output properly. This does not indicate a malfunction.
Audio
cable
Component
Video cable
Antenna
cable
VCR DVD Player Audio SystemDVD Player
Audio/
Video cable
Audio/
Video cable
VCR
Antenna
cable
or
If cannot receive
FM signal
Antenna
selector
FM
signal
TV signal
TV, CATV, Satellite
F Troubleshooting
If you find any problem while viewing your TV, you can either use the
“Factory Settings” function (see M) or check the Troubleshooting guide below.
If the problem persists, contact your Sony dealer.
Snowy picture, noisy sound
Check the antenna setup and other connections.
•Preset the channel manually again (see L).
Set the “Signal Booster” to “Auto” (see L) or try using an external booster.
Distorted picture, noisy sound
Set the “Signal Booster” to “Off” (see L), or turn off or disconnect any external booster in
use.
Good picture, noisy sound
Select the appropriate “TV System” (see L).
No picture, no sound
Check the power cord, antenna setup and other connections.
•Press 4/1 (power) to turn on the TV.
•Press 1 (main power) on the TV to turn off the TV for about five seconds, then turn it on
again.
Good picture, no sound
•Press 2 + to increase the volume level or press to cancel the muting.
Dotted lines or stripes
Do not use a hair dryer or other equipment near the TV.
Check the antenna setup.
Double images or “ghosts”
Use the fine tuning (“Fine”) function (see L).
Check the antenna setup or use a highly directional antenna.
•Turn off or disconnect any external booster in use.
No color
Adjust the “Color” level from “Picture Adjustment” (see J).
Select the appropriate “Color System” (see M).
Check the antenna setup.
Picture slant
Keep external speakers or other electrical equipment away from the TV.
Adjust the “Picture Rotation” (see M).
Abnormal color patches
Keep external speakers or other equipment away from the TV. Do not move the TV while
the TV is turned on. Press 1 (main power) on the TV to turn off the TV for about 15
minutes, then turn it on again to demagnetize the TV.
Teletext display is incomplete (snowy picture or double images).
Check the antenna setup and other connections.
Set the “Signal Booster” to “Auto” (see L) or try using an external booster.
Use the fine tuning (“Fine”) function (see L).
TV cannot receive stereo broadcast sound or stereo broadcast sound switches on and off or is distorted.
Check the antenna setup and other connections.
TV cannot receive FM radio station.
Connect a separate FM antenna and the TV channel source through an antenna selector
(switch) to your TV (see E).
Troubleshooting (continued)
The 1 (standby) indicator on your TV flashes red several times after every three seconds.
Count the number of times the 1 (standby) indicator flashes. Press 1 on the TV to turn it
off, disconnect the AC power cord and inform your dealer or Sony service center of how
the indicator flashes (duration and interval).
The TV screen sometimes goes blank for slightly longer than usual during channel change.
The “Signal Booster” is functioning to detect a weak signal. This does not indicate a
malfunction.
TV cabinet creaks.
Changes in room temperature sometimes make the TV cabinet expand or contract, causing
a noise. This does not indicate a malfunction.
A small “boom” sound is heard when the TV is turned on.
The TV’s demagnetizing function is working. This does not indicate a malfunction.
G TV buttons and remote control
TV
1
2
3
4
6
7
8
9
0
5
PROG
A/B
1
2
3
7
4
5
qj
qk
qa
qd
qf
qh
RETURN
6
8
9
0
w;
ql
qg
qs
WEGA
GATE
1 ?/1 Turn off temporarily or turn on the
TV.
2 a Display the TV program.
3 Jump to last program number that
has been watched for at least five
seconds.
4 PROG +/– Select program number. To select
quickly, press and hold until the
desired program number appears.
5 2 +/– Adjust volume.
8 Change the picture size:
“On” (16:9 wide mode), “Off”.
9 Select surround mode options (see
K).
0
Display on-screen information.
qa Mute the sound.
qs A/B Select stereo/bilingual mode:
Broadcasting Display (selected sound)
NICAM stereo NICAM (stereo), Mono (regular)
NICAM bilingual NICAM Main (main), NICAM
Sub (sub), Mono (regular)
NICAM monaural NICAM Main (main), Mono
(regular)
A2 stereo Stereo (stereo), Mono (regular)
A2 bilingual Main (main), Sub (sub)
• If the stereo sound is noisy when receiving a
stereo program, select “Mono”. The sound
becomes monaural, but the noise is reduced.
FM
3 2678
1
54
1 1 Turn off or turn on the TV.
2
Remote control sensor.
3
Wake Up indicator.
3 1 Standby indicator.
4 PROG +/– Select program number.
5 2 +/– Adjust volume.
6 t Select TV or video input.
WEGA GATE menu operations (see I)
4,5
, , ,
Select or adjust items.
6
Confirm selected items.
7 WEGA GATE Display or cancel WEGA
GATE menu.
8 FM Listen to FM radio (see
H).
TV buttons and remote control (continued)
qd t Select TV or video input.
qf 0-9 Input numbers. For program numbers 10 and above, enter the second
digit within two seconds.
ql Select sound mode options with a 5-Band Graphic Equalizer display:
“Dynamic”, “Standard”, “Custom”* (see K).
100 300 1k 3k 8k
Dynamic
100 300 1k 3k 8k
Standard
100 300 1k 3k 8k
Custom
* When the “Custom” mode is selected, you can receive the last adjusted
sound settings from the “Sound Adjustment” option in the menu.
w; Select picture mode options: “Vivid”, “Standard”, “Custom”* (see J).
* When the “Custom” mode is selected, you can receive the last adjusted
picture settings from the “Picture Adjustment” option in the menu.
WEGA GATE menu operations (see I)
6 Confirm selected items.
7 WEGA GATE Display or cancel WEGA GATE menu.
qj V, v, B, b Select or adjust items.
qk RETURN Return to the previous level.
Timer operations
qg Set TV to turn on automatically according to the desired period of time
(Wake Up Timer) (max. of 12 hours). The indicator on TV lights up amber once you set
the wake up timer. If no buttons or controls are pressed for more than
three hours after the TV is turned on using the wake up timer, the TV
automatically goes into standby mode.
qh Set TV to turn off automatically according to the desired period of time
(Sleep Timer) (max. of one hour and 30 min.).
Teletext operations (green icon)
Display Teletext broadcast: Teletext t Teletext and TV t TV. If there is
no Teletext broadcast, only “100” is displayed at the top left corner of the
screen.
Display Teletext service contents.
0-9
Input three digits Teletext page number.
,
Display the next or previous page.
Stop Teletext display from scrolling.
Reveal concealed information.
Enlarge the Teletext display.
Show TV screen while waiting for Teletext page. Enter the Teletext page
number that you want to refer to, then press
.
When the page number
is displayed, press
to show the text
.
(red, green, Access the corresponding colored FASTEXT menu. The FASTEXT
yellow, blue) feature can be used only when the FASTEXT broadcast is available.
PIP operations
, , V, v, B, b Not function for your TV.
Manufactured under license from BBE Sound, Inc.
Licensed by BBE Sound, Inc. under one or more of the following US patents: 5510752,
5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc.
TV buttons and remote control (continued)
H Listening to the FM Radio
You are able to listen to the FM radio stations using your TV by connecting an
antenna (see E).
To access to FM Radio mode:
Press WEGA GATE button and select “FM Radio” (see I).
or
Press FM button on the front panel (see G).
To exit from FM Radio mode:
Press WEGA GATE button, select the desired items: “TV” or “External
Inputs”, then press
. Select the desired TV channel or external inputs and
press .
or
Press FM button on the front panel.
A/B
PROG
+/–
V, v,
B, b
WEGA
GATE
TV
1
2
3
4
6
7
8
9
0
5
PROG
A/B
WEGA
GATE
RETURN
Listening to preset stations
1
Access to FM Radio mode.
2
Press WEGA GATE button and select “Settings”.
Preset the desired FM radio stations in “FM Radio
Setup” from “Channel Setup” menu (see L).
3
Exit from “Channel Setup” menu by pressing
WEGA GATE button. The selected preset FM radio
station number and label will appear on the screen.
To select the desired preset FM radio station, press
PROG +/–.
• You can also use the 1-9 buttons on the remote control
to directly select the desired preset FM radio station.
Listening to non-preset stations
1
Access to FM Radio mode.
2
Press V or v to search for the desired FM radio station. The preset number
and label will not be displayed.
You can only operate V, v, B and b functions using the remote control buttons in FM
Radio mode.
The available radio frequency is only for temporary listening pleasure and cannot be
stored in the memory.
If the message “Please setup FM Radio” appears, display the “Channel Setup” menu
and select “FM Radio Setup” to preset the desired FM radio stations (see L).
If the station has a noisy sound, you may be able to improve the sound quality by pressing
B or b.
When a FM stereo program has static noise, press A/B until “Mono” appears. There will
be no stereo effect, but the noise will be reduced.
01
02
03
04
05
TV
Confirm
Select
End
Confirm
End
Picture
Select
Color Temperature: Cool
Picture Adjustment
Picture Mode: Vivid
Intelligent Picture: On
Signal Level Indicator: On
Confirm
Select
WEGA GATE
Settings
External Inputs
FM Radio
TV
External Inputs
Confirm
Select
End
Video 1
1
2
DVD
Video 2
Preset 1:
---.--
Please setup FM Radio
FM Radio
Select Preset 1-9
Search
Exit
Fine
I WEGA GATE navigator
WEGA GATE is a gateway that allows you access to preset TV channels,
connected external inputs, FM Radio mode and “Settings” menu.
How to use WEGA GATE
watch the preset TV
channels (see D)
select the inputs for the
connected equipment
(see E)
change the settings
of your TV
(see J,K,L,M)
“TV”
“External Inputs”
“Settings”
(1) Press WEGA GATE to display or cancel
the WEGA GATE menu.
(3) Press V or v to select the desired item.
(4) Press RETURN to move to the previous
level.
(2) Press (or b) to confirm your selection
or go to the next level.
When a feature is dimmed in the menu, it is not selectable.
The WEGA GATE, and
, , ,
buttons on the front panel can also be used for
the operations above.
Confirm
Select
WEGA GATE
Settings
External Inputs
FM Radio
TV
01
02
03
04
05
TV
Confirm
Select
End
01
02
03
04
05
TV
Confirm
Select
End
Confirm
Select
WEGA GATE
Settings
External Inputs
FM Radio
TV
“FM Radio”
listen to the FM Radio
(see H)
J “Picture” setting
Press WEGA GATE and select “Settings”.
Make sure the “Picture” icon (
) is selected,
then press
.
“Picture Mode” Choose either “Vivid” (bright, contrast and sharp),
“Standard” (normal) or “Custom”*.
“Color Temperature” Adjust white color tint.
Choose either “Cool” (blue tint), “Neutral” (neutral tint) or
“Warm” (red tint).
“Intelligent Picture” Optimize picture quality.
Press V or v to select “On”, then press .
To cancel, select “Off”, then press .
“Signal Level Indicator” Display the signal level when the “Intelligent Picture” is
functioning.
“Intelligent Picture Signal Level” indicator will be displayed,
followed by picture improvement when you change the
program number or the input mode.
red amber green
(weak) (average)(fair ................. good)
Press V or v to select “On”, then press .
To cancel, select “Off”, then press . “Intelligent Picture” is
still functioning.
*You can adjust the setting to your personal preference in the “Picture Adjustment” and
“Color Temperature” options only when the “Custom” mode is selected.
Adjusting the “Picture Adjustment” items under “Custom”
mode
1
Press V or v to select either “Picture” (contrast), “Brightness”, “Color”,
“Hue” (color tones) or “Sharpness”, then press
.
Selecting “Reset” will set your TV to the factory settings.
2
Press V,v,B or b to adjust the setting of your selected item, then press .
3
Repeat the above steps to adjust other items.
The adjusted settings will be received when you select “Custom”.
“Hue” can be adjusted for the NTSC color system only.
Reducing “Sharpness” can also reduce picture noise.
Confirm
End
Picture
Select
Color Temperature: Cool
Picture Adjustment
Picture Mode: Vivid
Intelligent Picture: On
Signal Level Indicator: On
K “Sound” setting
Press WEGA GATE and select “Settings”.
Press V or v to select the “Sound” icon (
),
then press
.
“Sound Mode” Choose either “Dynamic” (low and high tones), “Standard”
(voice and high tones) or “Custom”*.
“Balance” Press v or B to emphasize the left speaker.
Press V or b to emphasize the right speaker.
“Intelligent Volume” Adjust the volume of all program numbers and video inputs
automatically.
Press V or v to select “On”, then press .
To cancel, select “Off”, then press .
“Surround” Choose either “Movie” (cinema surround effect for stereo
sound), “Sports” (simulated stadium effect for monaural sound)
or “Off”.
*You can adjust the setting to your personal preference in the “Sound Adjustment”
option only when the “Custom” mode is selected.
Adjusting the “Sound Adjustment” items under “Custom”
mode
The 5-Band Graphic Equalizer feature allows you to adjust sound frequency settings
of “Custom” mode in the menu.
1
Make sure that “Adjust” is selected, then press .
Selecting “Reset” will set your TV to the factory settings.
2
Press B or b to select the desired sound frequency, then press V or v to
adjust the setting and press .
The adjusted settings will be received when you select “Custom”.
Adjusting higher frequency will affect higher pitched sound and adjusting lower
frequency will affect lower pitched sound.
•You may display the settings directly by using the button on the remote control (see
G).
Confirm
End
Sound
Balance
Sound Adjustment
Sound Mode: Dynamic
Intelligent Volume: Off
Surround: Off
Select
L
“Channel Setup” setting
Press WEGA GATE and select “Settings”.
Press V or v to select the “Channel Setup”
icon ( ), then press .
“Auto Program” Preset channels automatically.
“Manual Program” Manually preset desired channels and channels that cannot
be preset automatically (see Presetting channels manually).
“Program Sorting/Edit”
Sort and edit the channels.
(a) If you wish to keep the channels in the current condition,
press WEGA GATE to exit.
(b) Press
V or v to select the program number with the
channel you wish to change. The selected channel will
appear on the screen.
(c) If you wish to store the channels in a different order:
(1) Press b to enter sorting mode.
(2) Press V or v to select the new program number
position for your selected channel, then press B.
(d) If you wish to edit the channels, press to change to
edit mode.
Press b until the mode that you wish to edit is
highlighted: Label, Skip, (block symbol). Then press
.
(1) To label, press V or v to select the alphanumeric
characters for the label. Then press .
(2) To skip the program number, press V or v to select
“On”. Then press .
You can skip this program number when using
PROG +/–.
(3) To block unwanted program number, press V or v to
select . Then press .
(e) Repeat step (b) to (d) if you wish to change other
channels.
Press WEGA GATE to exit.
Confirm
End
Channel Setup
Select
Auto Program
Manual Program
Program Sorting/Edit
FM Radio Setup
“Channel Setup” setting (continued)
“FM Radio Setup”* Preset up to nine FM radio stations.
You can manually preset each FM radio station that can be
received in your area and then store the radio frequency of the
desired FM radio stations.
(1) Press
V or v
to select the desired FM radio station
position, then press .
(2) Press
V or v
to search the FM radio stations.
Searching stops automatically when a station is tuned in.
If the station has a noisy sound, you may be able to improve
the sound quality by pressing
B or b
.
Press to store the FM radio station.
(3) You may edit the FM radio station label. Press
V or v
to
select alphanumeric characters for the label, then press
.
(4) Repeat steps (1) through (3) to preset other FM radio
stations.
* The “FM Radio Setup” feature is only available in FM
Radio mode. To
enable this feature, access to FM Radio
mode by using WEGA GATE system (see
I
) or pressing the
FM button on the front panel (see
G
), then preset your desired
FM radio stations according to the steps mentioned above.
If you preset a blocked program number, that program number will be unblocked
automatically.
If you sort a blocked program, that program will remain blocked.
Presetting channels manually
1
After selecting “Manual Program”, select the program
number to which you want to preset a channel.
(1) Make sure “Program” is selected, then press
.
(2) Press V or v
until the program number you want
to preset appears on the menu, then press
.
2
Select the desired channel.
(1) Make sure either “VHF Low”, “VHF High” or “UHF” is selected, then press
.
(2) Press V or v until the desired channel’s broadcast appears on the TV screen,
then press .
3
If the sound of the desired channel is abnormal, select the appropriate TV
system.
(1) Press V or v
to select “TV System”, then press .
(2) Press V or v
until the sound becomes normal, then press .
4
If you are not satisfied with the picture and sound quality, you may be able
to improve them by using the “Fine” tuning feature.
(1) Press V or v
to select “Fine”, then press .
(2) Press V or v
to select “Manual”, then press .
(3)
Press V,v,B or b until the picture and sound quality are optimal, then press .
The + or – icon on the menu flashes while tuning.
5
If the TV signal is too strong (picture distorted; picture with lines; signal
interference) or weak (snowy picture), you may be able to improve the
picture quality by setting the “Signal Booster” feature.
(1) Press V or v
to select “Signal Booster”, then press .
(2) Press V or v
to select either “Off” (for picture distorted; picture with lines;
signal interference) or “Auto” (for snowy picture), then press
.
01
“Channel Setup” setting (continued)
M
“Setup” setting
Press WEGA GATE and select “Settings”.
Press V or v to select the “Setup” icon (
),
then press .
“Language” Change the menu language.
Press V or v to select either “English” or “Русский” (Russian),
then press .
“Picture Rotation” Adjust the picture position when it is not aligned with the TV
screen.
Press B or b to adjust the picture position, then press .
“Video Label” Label the connected equipment.
(1) Select “Video Input” and press . Press V or v to select the
input you want to label, then press .
(2) Select “Label” and press , then press V or v to select
the label options: “Video 1”/“Video 2”/“DVD”, “VCR”,
“SAT”, “Game” or “Edit”*.
* You may edit the video label to your favorite name. Press V or v
to select alphanumeric characters for the label, then press .
“Color System” Select the color system.
Press V or v to select either “Auto”, “PAL”, “SECAM”,
“NTSC3.58” or “NTSC4.43”, then press . Normally, set this to
“Auto”.
“Wake Up Timer
Allow your TV to emit beeping sound when TV switches on
Beep
automatically using wake up timer.
Press V or v to select “On”, then press .
To cancel, select “Off”, then press .
“Factory Settings”
Reset your TV to factory settings.
Press and press V or v to select “Yes”. Then press .
Your TV will go blank for a few seconds, then the “Initial Setup”
menu will appear.
To cancel, select “No”, then press .
Color system is not selectable in FM Radio mode.
•To ensure the beeping sound can be heard, you must set an appropriate volume
level on your TV and make sure the TV is not in mute condition.
•To stop the beeping sound, press any buttons on the remote control or front panel.
If no button is pressed for three minutes, the beeping sound will automatically go
off.
Confirm
End
Setup
Select
Language:
Picture Rotation
Video Label
Color System: Auto
Factory Settings
English
On
Wake Up Timer Beep:
Tr initron Color TV
© 2007 Sony Corporation
KV-HG21
3-213-968-11 (1)
RU
M91
Инструкция по эксплуатации
Перед работой с устройством внимательно прочтайте инструкцию
и сохраните её для дальнейшего использования.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38

Sony KV-HG21 Руководство пользователя

Категория
Телевизоры CRT
Тип
Руководство пользователя
Это руководство также подходит для

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ