Sony MDX-C6500RX Инструкция по применению

Operating Instructions

Manual de instrucciones

Bruksanvisning

Manual de instruções

Инструкция по эксплуатации

GB

ES

PT

SE

For installation and connections, see the supplied installation/connections

manual.

Para obtener información sobre la instalación y las conexiones, consulte el manual

de instalación/conexiones suministrado.

Vi hänvisar till det medföljande häftet angående montering/anslutningar.

Para a instalação e as ligações, consulte o manual de instalação/ligações

fornecido.

Перед установкой и подсоединениями прочитайте прилагаемую

инструкцию по установке и подсоединению.

FM/MW/LW

MiniDisc Player

MDX-C6500RX MDX-C6500RV

MDX-C6500R MDX-C6400R

3-044-659-12 (1)

RU

2

Welcome !

Thank you for purchasing the Sony MiniDisc

Player. This unit lets you enjoy a variety of

features using the following controller

accessories:

Optional accessories

Rotary commander RM-X4S

Card remote commander RM-X91

In addition to the MD playback and radio

operations, you can expand your system by

connecting optional CD/MD units*

1

.

When you operate this unit or a connected

optional CD unit with the CD TEXT function,

the CD TEXT information will appear in the

display when you playback a CD TEXT disc*

2

.

*

1

You can connect MD changers, CD changers, MD

players, or CD players.

*

2

A CD TEXT disc is an audio CD that includes

information such as the disc name, artist name

and track names.

This information is recorded on the disc.

Precautions

• If your car was parked in direct sunlight

resulting in a considerable rise in

temperature inside the car, allow the unit to

cool off before operating it.

• If no power is being supplied to the unit,

check the connections first. If everything is in

order, check the fuse.

•If your car is equipped with a power aerial, it

will extend automatically while the unit is

operating.

If you have any questions or problems

concerning your unit that are not covered in

this manual, please consult your nearest Sony

dealer.

Moisture Condensation

On a rainy day or in a very damp area,

moisture may condense on the lenses inside

the unit. Should this occur, the unit will not

operate properly. In such a case, remove the

disc and wait for about an hour until the

moisture has evaporated.

To maintain high quality sound

If you have drink holders near your audio

equipment, be careful not to splash juice or

other soft drinks onto the unit and MD. Sugary

residues on the unit or MD may contaminate

the lenses inside the unit, reduce the sound

quality, or prevent sound reproduction

altogether.

3

Notes on MDs

Since the disc itself is housed in a cartridge,

free from accidental contact with your fingers

and dust, MDs can withstand a certain degree

of the rough handling. However, dirt or dust

on the surface of the cartridge or a warped

cartridge may cause a malfunction. Observe

the following for best results.

Never touch the surface of the disc itself by

deliberately opening the shutter on the

cartridge.

When you eject the MD, the shutter may be

open. In such a case, close the shutter

immediately.

Do not expose the MD to direct sunlight or

heat sources such as hot air-ducts. Do not leave

it in a car parked in direct sunlight where there

can be a considerable rise in temperature.

Make sure the MD is not left on the dashboard

or rear tray of a car, etc. where the temperature

can also be excessive.

Notes on attaching labels

Be sure to attach labels on cartridges correctly,

as failing to do so may cause the MD to

become stuck in the unit.

•Attach the label in a suitable position.

•Remove old labels before putting new ones

on.

•Replace labels that are beginning to peel

away from the MD.

Cleaning

Wipe the surface of the cartridge from time to

time with a soft dry cloth.

4

Table of Contents

Location of controls ............................................. 5

Getting Started

Resetting the unit ................................................. 7

Detaching the front panel ................................... 7

Turning the unit on/off ....................................... 8

How to use the menu .......................................... 8

Setting the clock ................................................... 8

MD Player

CD/MD Unit (optional)

Listening to an MD .............................................. 9

Playing tracks repeatedly

— Repeat Play ............................................... 11

Playing tracks in random order

— Shuffle Play ............................................... 11

Labelling a CD

— Disc Memo* .............................................. 12

Locating a disc by name

— List-up* ..................................................... 13

Selecting specific tracks for playback

— Bank* ......................................................... 14

* Functions available with optional CD/MD unit

Radio

Memorising stations automatically

— Best Tuning Memory (BTM)................... 15

Memorising only the desired stations............. 15

Receiving the memorised stations ................... 16

RDS

Overview of the RDS function ......................... 17

Displaying the station name............................. 17

Retuning the same programme automatically

— Alternative Frequencies (AF) ................. 17

Listening to traffic announcements ................. 18

Presetting the RDS stations with

the AF and TA data ....................................... 19

Locating a station by programme type ........... 20

Setting the clock automatically ........................ 21

Other Functions

Labelling the rotary commander ..................... 21

Using the rotary commander ........................... 22

Adjusting the sound characteristics ................ 23

Attenuating the sound ...................................... 24

Changing the sound and display settings ...... 24

Boosting the bass sound

— D-bass ........................................................ 25

Additional Information

Maintenance........................................................ 25

Dismounting the unit ........................................ 27

Specifications ...................................................... 28

Troubleshooting guide ...................................... 29

5

Location of controls

Refer to the pages listed for details.

1 Volume control dial 19

2 MENU button 8, 10, 12, 13, 14, 15, 16,

18, 19, 21, 24

3 DISC/PRST +/– (cursor up/down) buttons

8, 10, 12, 13, 14, 15, 16, 18, 19, 20, 21, 24

During CD/MD playback:

Disc change 10, 13

During radio reception:

Preset stations select 16

4

Z (eject) button (located on the front

side of the unit behind the front panel)

9

5 DSPL/PTY (display mode change/

programme type) button 9, 10, 12, 17,

20

6 LIST button 12

List-up 13

7 SOURCE (TUNER/CD/MD) button

8, 9, 10, 13, 15, 16, 19

8 Display window

9 OPEN button 7, 9, 26

q; D-BASS button 25

qa SOUND button 23

qs Reset button (located on the front side

of the unit behind the front panel) 7

qd OFF button* 7, 8, 9

qf SEEK/AMS –/+ (cursor left/right) buttons

8, 10, 12, 14, 16, 18, 19, 21, 23, 24

Automatic Music Sensor 10, 14

Manual Search 10

Seek 15, 16, 18

qg ENTER button 8, 10, 12, 13, 14, 15, 16,

18, 19, 20, 21, 24

qh MODE button 19

During CD or MD playback:

CD/MD unit select 9, 13

During radio reception:

BAND select 15, 16

qj Receptor for the card remote

commander

qk Number buttons

During radio reception:

Preset number select 15, 16, 18, 19

During CD/MD playback:

(1) REP 11

(2) SHUF 11

ql AF button 17, 18, 19

w; TA button 18, 19

* Warning when installing in a car

without ACC (accessory) position on

the ignition key switch

Be sure to press (OFF) on the unit for two

seconds to turn off the clock display after

turning off the engine.

When you press (OFF) only momentarily,

the clock display does not turn off and this

causes battery wear.

MDX-C6500RX/C6500RV

/C6500R/C6400R

D

I

S

C

+

P

R

S

T

+

-

D

I

S

C

–

P

R

S

T

-

LIST

DSPL

AF

OFF

PTY

ENTER

MENU

SOUND

1 2 3 4 56

SOURCE

-

SEEK/AMS

REP SHUF

TA

OPEN

D-BASS

MODE

6

Location of controls

Card remote commander RM-X91 (optional)

The corresponding buttons of the card

remote commander control the same

functions as those on this unit.

1 OFF button

2 MENU button

3 SOURCE button

4 SEEK/AMS buttons

5 SOUND button

6 DSPL (DSPL/PTY) button

7 ATT button

8 LIST button

9 DISC/PRST buttons

q; ENTER button

qa MODE button

qs VOL buttons

OFF

SEEK SEEK

OPEN/CLOSE

MENU LIST

SOUND

ENTER

DISC

SOURCE

DSPL MODE

VOLATT

Notes

• A unit turned off by pressing (OFF) for 2 seconds cannot be operated with the card remote commander

unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.

• Do not leave the card remote commander where it can be exposed to direct sunlight such as on a

dashboard or the steering wheel, etc. The card remote commander may be deformed by the heat.

• The MiniDisc recorder may not operate properly with the card remote commander in direct sunlight. In

such a case, hold the card remote commander close to the unit’s receptor.

7

Attaching the front panel

Place the hole A in the front panel onto the

spindle B on the unit as illustrated, then push

the left side in.

x

Notes

• Be careful not to attach the front panel upside

down.

• Do not press the front panel too hard against the

unit when attaching it.

• Do not press too hard or put excessive pressure

on the display window of the front panel.

• Do not expose the front panel to direct sunlight

or heat sources such as hot air ducts, and do not

leave it in a humid place. Never leave it on the

dashboard of a car parked in direct sunlight or

where there may be a considerable rise in

temperature.

Caution alarm

If you turn the ignition key switch to the OFF

position without removing the front panel, the

caution alarm will beep for a few seconds.

If you connect an optional power amplifier and

do not use the built-in amplifier, the beep

sound will be deactivated.

Getting Started

Resetting the unit

Before operating the unit for the first time or

after replacing the car battery, you must reset

the unit.

Remove the front panel and press the reset

button with a pointed object, such as a ball-

point pen.

Reset button

Note

Pressing the reset button will erase the clock

setting and some memorised functions.

Detaching the front panel

You can detach the front panel of this unit to

protect the unit from being stolen.

1 Press (OFF).

2 Press (OPEN), then slide the front panel

to the right side, and pull out the left

side of the front panel.

Notes

• Do not put anything on the inner surface of the

front panel.

• Be sure not to drop the panel when detaching it

from the unit.

• If you detach the panel while the unit is still

turned on, the power will turn off automatically

to prevent the speakers from being damaged.

• When carrying the front panel with you, use the

supplied front panel case.

1

2

A

B

8

Turning the unit on/off

Turning on the unit

Press (SOURCE) or insert an MD in the unit.

For details on operation, refer to page 9 (MD/

CD) and page 15 (radio).

Turning off the unit

Press (OFF) to stop MD/CD playback or radio

reception (the key illumination and display

remain on).

Press (OFF) for two seconds to completely

turn the unit off.

Note

If your car has no ACC position on the ignition key

switch, be sure to turn the unit off by pressing

(OFF) for two seconds to avoid car battery wear.

How to use the menu

This unit is operated by selecting items from a

menu.

To select, first enter the menu mode and

choose up/down ((+)/(–) of (DISC/PRST)), or

choose left/right ((–)/(+) of (SEEK/AMS)).

(DISC/PRST)

SOURCE

(SEEK/AMS)

SOURCE

(+): to select upwards

(–): to select downwards

Setting the clock

The clock uses a 24-hour digital indication.

Example: To set the clock to 10:08

1 Press (MENU), then press either side of

(DISC/PRST) repeatedly until “CLOCK”

appears.

1 Press (ENTER).

The hour indication flashes.

2 Press either side of (DISC/PRST) to set

the hour.

3 Press the (+) side of (SEEK/AMS).

The minute indication flashes.

4 Press either side of (DISC/PRST) to set

the minute.

2 Press (ENTER).

The clock starts.

After the clock setting is completed, the

display returns to normal play mode.

Tip

You can set the clock automatically with the RDS

feature (see page 17).

Note

When the D.INFO mode is set to ON, the time is

always displayed, provided that the M.DSPL is set

to OFF (page 24).

(–): to select

leftwards

(+): to select

rightwards

Note

In Menu mode the “v” in the left of the display

indicates the selectable buttons of (DISC/PRST)

and (SEEK/AMS).

9

MD Player

CD/MD Unit (optional)

In addition to playing an MD with this unit

alone, you can also control external CD/MD

units.

If you connect an optional CD unit with the

CD TEXT function, the CD TEXT information

will appear in the display when you play a CD

TEXT disc.

Listening to an MD

(with this unit only)

1 Press (OPEN) and insert the MD.

Labelled side up

2 Close the front panel.

Playback starts automatically.

If an MD is already inserted, press (SOURCE)

repeatedly until “MD” appears to start

playback.

The title of the MD* and the track title will

appear in the display window, then the

playing time will appear.

MD indication

* Only if these titles are prerecorded on the MD.

Elapsed playing timeTrack number

When the last track on the MD is

over

The track number indication returns to “1,”

and playback restarts from the first track of the

MD.

To Press

Stop playback (OFF)

Eject the MD (OPEN) then Z

Playing a CD or MD

(with an optional CD/MD unit)

1 Press (SOURCE) repeatedly to select

“CD“ or “MD.“

2 Press (MODE) until the desired unit

appears.

CD/MD playback starts.

All the discs in the current CD/MD unit is

played from the top.

Changing the display item

Each time you press (DSPL/PTY) during MD,

CD, or CD TEXT disc playback, the item

changes as follows:

V

Disc number*

1

/Track number/

Elapsed playback time

V

Disc name*

2

/Artist name*

3

V

Track name*

4

V

FM1 frequency or station name*

5

*

1

While an optional CD/MD unit is connected.

*

2

If you have not labelled the CD or CD TEXT disc

(“Labelling a CD” on page 12), or if there is no

disc name prerecorded on the MD, “DISC“ and

“NO NAME” appear in the display.

*

3

If you play a CD TEXT disc, the artist name

appears in the display after the disc name. (Only

for CD TEXT discs with the artist name.)

*

4

If the track name of a CD TEXT disc or MD is not

prerecorded, “TRACK“ and “NO NAME” appear

in the display.

*

5

While the AF/TA function is activated.

Z

10

After you select the desired item, the display

will automatically change to the Motion

Display mode after a few seconds.

In the Motion Display mode, all the items are

scrolled in the display one by one in order.

Note

If you use personalised labels, they will always

take priority over the original CD TEXT

information when such information is

displayed.

Tip

The Motion Display mode can be turned off. (See

“Changing the sound and display settings” on

page 24).

Automatically scrolling a disc name

— Auto Scroll

If the disc name, artist name, or track name on

an MD or a CD TEXT disc exceeds 8 characters

and the Auto Scroll function is on, information

automatically scrolls across the display as

follows:

• The disc name appears when the disc has

changed (if the disc name is selected as the

display item).

• The track name appears when the track has

changed (if the track name is selected as the

display item).

• The disc or track name appears depending on

the setting when you press (SOURCE) to select

an MD or CD TEXT disc.

If you press (DSPL/PTY) to change the display

item, the disc or track name of the MD or CD

TEXT disc is scrolled automatically whether

you set the function on or off.

1 During playback, press (MENU).

2 Press either side of (DISC/PRST)

repeatedly until “A.SCRL-OFF” appears.

3 Press the (+) side of (SEEK/AMS) to select

“A.SCRL-ON.”

4 Press (ENTER).

To cancel Auto Scroll, select “A.SCRL-OFF” in

step 3.

Note

For some CD TEXT discs with very many characters,

the following cases may happen:

— Some of the characters are not displayed.

— Auto Scroll does not work.

Locating a specific track

— Automatic Music Sensor (AMS)

During playback, press either side of

(SEEK/AMS) momentarily for each track

you want to skip.

SOURCE

Locating a specific point in a track

— Manual Search

During playback, press and hold either

side of (SEEK/AMS). Release when you

have found the desired point.

SOURCE

Note

If “

” or “ ” appears in the

display, you have reached the beginning or the

end of the disc and you cannot go any further.

Locating a disc

— Disc Selection

When an optional CD/MD unit is

connected, press either side of

(DISC/PRST) to select the desired disc.

The desired disc in the current optional

CD/MD unit begins playback.

To locate

preceding

tracks

To locate

succeeding

tracks

To search

forward

To search

backward

11

LIST

DSPL

PTY

ENTER

1 2 3 4 56

-

SEEK/AMS

REP SHUF

MODE

LIST

DSPL

PTY

ENTER

1 2 3 4 56

-

SEEK/AMS

REP SHUF

MODE

Playing tracks repeatedly

— Repeat Play

The MD in the main unit will automatically

repeat itself when it reaches the end. As repeat

play, you can select:

•REP-1 — to repeat a track.

•REP-2 — to repeat a disc in the optional CD/

MD unit.

During playback, press (1) (REP)

repeatedly until the desired setting

appears in the display.

B REP-1 B REP-2*

REP-OFF b

* “REP-2” is only available when you connect

one or more optional MD units, or when you

connect two or more optional CD units.

Repeat Play starts.

To return to normal play mode, select “REP-

OFF”.

Playing tracks in random

order — Shuffle Play

You can select:

•SHUF-1 — to play the tracks on the current

disc in random order.

•SHUF-2 — to play the tracks in the current

optional CD/MD unit in random order.

•SHUF-ALL — to play all the tracks in all the

optional CD/MD units in random order.

During playback, press (2) (SHUF)

repeatedly until the desired setting

appears in the display.

B SHUF-1 B SHUF-2* B SHUF-ALL*

SHUF-OFF b

* “SHUF-2” and “SHUF-ALL” are only available

when you connect one or more optional MD

units, or when you connect two or more

optional CD units.

Shuffle Play starts.

To return to normal play mode, select “SHUF-

OFF”.

12

Labelling a CD — Disc Memo

(For a CD unit with the CUSTOM FILE

function)

You can label each disc with a personalised

name. You can enter up to eight characters for

a disc. If you label a CD, you can locate the

disc by name (page 13) and select the specific

tracks for playback (page 14).

1 Start playing the disc you want to label.

2 Press (MENU), then press either side of

(DISC/PRST) repeatedly until ”NAME

EDIT” appears.

3 Press (ENTER).

Name edit mode

The unit will repeat the disc during the

labelling procedure.

4 Enter the characters.

1 Press the (+) side of (DISC/PRST)

repeatedly to select the desired

characters.

(A t B t C t ··· Z t 0 t 1 t 2 t

··· 9 t + t – t * t / t \ t > t <

t . t _ )

If you press the (–) side of (DISC/PRST)

repeatedly, the characters will appear in

reverse order.

If you want to put a blank space

between characters, select “_” (under-

bar).

2 Press the (+) side of (SEEK/AMS) after

locating the desired character.

The next character flashes.

If you press the (–) side of (SEEK/AMS),

the previous character flashes.

3 Repeat steps 1 and 2 to enter the

entire name.

5 To return to normal CD play mode, press

(ENTER).

Tips

• To erase or correct a name, enter “_” (under-bar)

for each character.

• There is another way to start labelling a CD. Press

(LIST) for two seconds instead of steps 2 and 3.

You can also complete the operation by pressing

(LIST) for two seconds instead of step 5.

• You can label CDs on a unit without the CUSTOM

FILE function if that unit is connected along with

a CD unit that has the function. The disc name

will be stored in the memory of the CD unit with

the CUSTOM FILE function.

Displaying the disc memo

Press (DSPL/PTY) during CD or CD TEXT

disc playback.

Each time you press (DSPL/PTY) during CD

or CD TEXT disc playback, the item

changes as follows:

V

Disc number*

1

/Track number/

Elapsed playback time

V

Disc memo name

V

Track name*

2

V

FM1 frequency or station name*

3

*

1

While an optional CD unit is connected.

*

2

If you connect an optional CD unit with the

CD TEXT function, the CD TEXT information

will appear in the display when you play a

CD TEXT disc.

*

3

While the AF/TA function is activated.

13

Erasing the disc memo

1 Press (SOURCE) repeatedly to select

“CD.“

2 Press (MODE) repeatedly to select the CD

unit with the CUSTOM FILE function.

3 Press (MENU), then press either side of

(DISC/PRST) repeatedly until “NAME

DEL” appears.

4 Press (ENTER).

5 Press either side of (DISC/PRST)

repeatedly to select the disc name you

want to erase.

6 Press (ENTER) for two seconds.

The name is erased.

Repeat steps 5 and 6 if you want to erase

other names.

7 Press (MENU) twice.

The unit returns to normal CD play mode.

Notes

• To erase the disc memo, play a CD on the CD unit

in which the disc memo you want to erase is

stored.

• When a personalised label for a CD TEXT disc is

erased, the original CD TEXT information will

appear on the display.

Locating a disc by name

— List-up (For a CD unit with the CD TEXT

function/CUSTOM FILE function, or an MD

unit)

You can use this function for discs that have

been assigned custom names or for CD TEXT

discs.

You can locate the disc by

— its custom name: when you assign a name

for a CD or an MD using a CD unit with the

CUSTOM FILE function or an MD unit.

(For information on disc names, see

“Labelling a CD” on page 12).

— the CD TEXT information: when you play a

CD TEXT disc on a CD unit with the CD

TEXT function.

1 Press (LIST).

The name assigned to the current disc

appears in the display.

When you assign a disc memo name to a

CD TEXT disc, it takes priority over the

original CD TEXT information.

2 Press either side of (DISC/PRST)

repeatedly until you find the desired

disc.

3 Press (ENTER) to play the disc.

Notes

• When using the card remote commander, press

(LIST) to return to normal play mode. When

operating just by the unit’s button, the display

returns to normal play mode after 5 seconds.

• The track names are not displayed during MD or

CD TEXT disc playback.

• If there are no discs in the CD/MD unit, “NO

DISC” appears in the display.

• If a disc has not been assigned a custom name,

“********” appears on the display.

• Some letters cannot be displayed during MD or

CD TEXT disc playback.

• If the disc information has not been read yet by

the unit, “NOT READ” is displayed.

14

Selecting specific tracks

for playback

— Bank

(For a CD unit with the CUSTOM FILE

function)

If you label the disc, you can set the unit to

skip or play the tracks of your choice.

1 Start playing the disc you want to label.

2 Press (MENU), then press either side of

(DISC/PRST) repeatedly until “BANK SEL”

appears.

3 Press (ENTER).

Bank edit mode

4 Label the tracks.

1 Press either side of (SEEK/AMS)

repeatedly to select the track you want

to label.

2 Press (ENTER) repeatedly to select

“PLAY” or “SKIP.”

5 Repeat step 4 to set “PLAY” or “SKIP” for

all the tracks.

6 Press (MENU) twice.

The unit returns to normal CD play mode.

Notes

• You can set “PLAY” and “SKIP” for up to 24

tracks.

• You cannot set “SKIP” for all the tracks on a CD.

Playing specific tracks only

You can select:

•“BANK-ON” — to play the tracks with the

“PLAY” setting.

•“BANK-INV” (Inverse) — to play the tracks

with the “SKIP” setting.

1 During playback, press (MENU), then

press either side of (DISC/PRST)

repeatedly until “BANK-ON,” “BANK-

INV,” or “BANK-OFF” appears.

2 Press the (+) side of (SEEK/AMS)

repeatedly until the desired setting

appears.

B BANK-ON B BANK-INV

BANK-OFF b

3 Press (ENTER).

Playback starts from the track following the

current one.

To return to normal play mode, select “BANK-

OFF” in step 2.

15

Memorising only the

desired stations

You can preset up to 18 FM stations (6 each for

FM1, FM2, and FM3), up to 6 MW stations,

and up to 6 LW stations in the order of your

choice.

1 Press (SOURCE) repeatedly to select the

tuner.

2 Press (MODE) repeatedly to select the

band.

3 Press either side of (SEEK/AMS) to tune

in the station that you want to store on

the number button.

4 Press the desired number button ((1) to

(6)) for two seconds until “MEM”

appears.

The number button indication appears in

the display.

Note

If you try to store another station on the same

number button, the previously stored station will

be erased.

Radio

Memorising stations

automatically

— Best Tuning Memory (BTM)

The unit selects the stations with the strongest

signals and memorises them in the order of

their frequencies. You can store up to 6 stations

on each band (FM1, FM2, FM3, MW, and LW).

Caution

When tuning in stations while driving, use

Best Tuning Memory to prevent accidents.

1 Press (SOURCE) repeatedly to select the

tuner.

Each time you press (SOURCE), the source

changes as follows:

B Tuner B CD* B MD

* If the corresponding optional equipment is

not connected, this item will not appear.

2 Press (MODE) repeatedly to select the

band.

Each time you press (MODE), the band

changes as follows:

B FM1 B FM2 B FM3

LW b MW b

3 Press (MENU), then press either side of

(DISC/PRST) repeatedly until “BTM”

appears.

4 Press (ENTER).

The unit stores stations in the order of their

frequencies on the number buttons.

A beep sounds when the setting is stored.

Notes

• The unit does not store stations with weak

signals. If only a few stations can be received,

some number buttons will retain their former

setting.

• When a number is indicated in the display, the

unit starts storing stations from the one currently

displayed.

• If an MD is not in the unit, only the tuner band

appears even if you press (SOURCE).

16

If FM stereo reception is poor

— Monaural Mode

1 During radio reception, press (MENU),

then press either side of (DISC/PRST)

repeatedly until “MONO-OFF” appears.

2 Press the (+) side of (SEEK/AMS) until

“MONO-ON“ appears.

The sound improves, but becomes

monaural (“ST” disappears).

3 Press (ENTER).

To return to normal mode, select

“MONO-OFF” in step 2.

Receiving the memorised

stations

1 Press (SOURCE) repeatedly to select the

tuner.

2 Press (MODE) repeatedly to select the

band.

3 Press the number button ((1) to (6)) on

which the desired station is stored.

Tip

Press either side of (DISC/PRST) to receive the

stations in the order they are stored in the

memory (Preset Search Function).

If you cannot tune in a preset

station

Press either side of (SEEK/AMS) to search

for the station (automatic tuning).

Scanning stops when the unit receives a

station. Press either side of (SEEK/AMS)

repeatedly until the desired station is

received.

Note

If the automatic tuning stops too frequently, press

(MENU), then press either side of (DISC/PRST)

repeatedly until “LOCAL” (local seek mode) is

displayed. Then press the (+) side of (SEEK/AMS) to

select “LOCAL-ON.” Press (ENTER).

Only the stations with relatively strong signals will

be tuned in.

Tips

• When you select the “LOCAL-ON” setting,

“L.SEEK” appears while the unit is searching for

a station.

• If you know the frequency of the station you

want to listen to, press and hold either side of

(SEEK/AMS) until the desired frequency appears

(manual tuning).

17

RDS

Overview of the RDS

function

Radio Data System (RDS) is a broadcasting

service that allows FM stations to send

additional digital information along with the

regular radio programme signal. Your car

stereo offers you a variety of services. Here are

just a few: retuning the same programme

automatically, listening to traffic

announcements, and locating a station by

programme type.

Notes

• Depending on the country or region, not all of

the RDS functions are available.

• RDS may not work properly if the signal strength

is weak or if the station you are tuned to is not

transmitting RDS data.

Displaying the station

name

The name of the current station lights up in the

display.

Select an FM station (page 16).

When you tune in an FM station that

transmits RDS data, the station name

appears in the display.

Note

The “*” indication means that an RDS station is

being received.

Changing the displayed item

Each time you press (DSPL/PTY), the item

changes as follows:

Station Name (Frequency) y PTY data

After you select the desired item, the display

will automatically change to the Motion

Display mode after a few seconds.

In the Motion Display mode, all the items are

scrolled in the display one by one in order.

Tip

The Motion Display mode can be turned off. (See

“Changing the sound and display settings” on

page 24.)

Note

“NO NAME” appears if the received station does

not transmit RDS data.

Retuning the same

programme automatically

— Alternative Frequencies (AF)

The Alternative Frequencies (AF) function

automatically selects and retunes the station

with the strongest signal in a network. By

using this function, you can continuously

listen to the same programme during a long-

distance drive without having to retune the

station manually.

1 Select an FM station (page 16).

2 Press (AF) repeatedly until “AF-ON”

appears.

The unit starts searching for an alternative

station with a stronger signal in the same

network.

Station

98.5MHz

102.5MHz

96.0MHz

Frequencies change automatically.

18

Local link function

(United Kingdom only)

The Local Link function lets you select other

local stations in the area, even if they are not

stored on your number buttons.

1 Press a number button that has a local

station stored on it.

2 Within five seconds, press the number

button of the local station again.

3 Repeat this procedure until the desired

local station is received.

Listening to traffic

announcements

The Traffic Announcement (TA) and Traffic

Programme (TP) data lets you automatically

tune in an FM station that is broadcasting

traffic announcements even if you are listening

to other programme sources.

Press (TA) repeatedly until “TA-ON”

appears.

The unit starts searching for traffic

information stations. “TP” appears in the

display when the unit finds a station

broadcasting traffic announcements.

When the traffic announcement starts,

“TA” flashes. The flashing stops when the

traffic announcement is over.

Tip

If the traffic announcement starts while you are

listening to another programme source, the unit

automatically switches to the announcement and

goes back to the original source when the

announcement is over.

Notes

• When there is no alternative station in the area

and you do not need to search for an alternative

station, turn the AF function off by pressing

(AF) repeatedly until “AF-OFF” appears.

• When “NO AF” and the station name flash

alternately, it means that the unit cannot find an

alternative station in the network.

• If the station name starts flashing after selecting

a station with the AF function on, this indicates

that no alternative frequency is available. Press

either side of (SEEK/AMS) while the station name

is flashing (within eight seconds). The unit starts

searching for another frequency with the same PI

(Programme Identification) data (“PI SEEK”

appears and no sound is heard). If the unit

cannot find another frequency, “NO PI” appears,

and the unit returns to the previously selected

frequency.

Listening to a regional programme

The “REG-ON” (regional on) function lets you

stay tuned to a regional programme without

being switched to another regional station.

(Note that you must turn the AF function on.)

The unit is factory preset to “REG-ON,” but if

you want to turn off the function, do the

following.

1 During radio reception, press (MENU),

then press either side of (DISC/PRST)

repeatedly until “REG” appears.

2 Press the (+) side of (SEEK/AMS) until

“REG-OFF” appears.

3 Press (ENTER).

Note that selecting “REG-OFF” might cause

the unit to switch to another regional

station within the same network.

To return to regional on, select “REG-ON” in

step 2.

Note

This function does not work in the United

Kingdom and in some other areas.

19

Notes

• “NO TP” flashes for five seconds if the received

station does not broadcast traffic

announcements. Then, the unit starts searching

for a station that broadcasts it.

• When “EON” appears with “TP” in the display,

the current station makes use of broadcast traffic

announcement of other stations in the same

network.

To cancel the current traffic

announcement

Press (TA), (SOURCE) or (MODE).

To cancel all traffic announcements, turn off

the function by pressing (TA) until “TA-

OFF” appears.

Presetting the volume of traffic

announcements

You can preset the volume level of the traffic

announcements beforehand so you won’t miss

the announcement. When a traffic

announcement starts, the volume will be

automatically adjusted to the preset level.

1 Turn the volume control dial to adjust

the desired volume level.

2 Press (TA) for two seconds.

“TA” appears and the setting is stored.

Receiving emergency

announcements

If an emergency announcement comes in while

you are listening to the radio, the programme

will be automatically switched to it. If you are

listening to a source other than the radio, the

emergency announcements will be heard if

you set AF or TA to ON. The unit will then

automatically switch to these announcements

no matter which source you are listening to at

the time.

Presetting the RDS

stations with the AF and

TA data

When you preset RDS stations, the unit stores

each station’s data as well as its frequency, so

you don’t have to turn on the AF or TA

function every time you tune in the preset

station. You can select a different setting (AF,

TA, or both) for individual preset stations, or

the same setting for all preset stations.

Presetting the same setting for all

preset stations

1 Select an FM band (page 15).

2 Press (AF) and/or (TA) to select “AF-ON”

and/or “TA-ON.”

Note that selecting “AF-OFF” or “TA-OFF”

stores not only RDS stations, but also

non-RDS stations.

3 Press (MENU), then press either side of

(DISC/PRST) repeatedly until “BTM”

appears.

4 Press the (+) side of (SEEK/AMS) until

“BTM” flashes.

5 Press (ENTER).

Presetting different settings for

each preset station

1 Select an FM band, and tune in the

desired station (page 16).

2 Press (AF) and/or (TA) to select “AF-ON”

and/or “TA-ON.”

3 Press the desired number button until

“MEM” appears.

Repeat from step 1 to preset other stations.

20

1 Press (DSPL/PTY) during FM reception

until “PTY” appears.

The current programme type name appears

if the station is transmitting the PTY data.

“- - - - -” appears if the received station is

not an RDS station, or if the RDS data has

not been received.

2 Press (DISC/PRST) repeatedly until the

desired programme type appears.

The programme types appear in the order

shown in the above table. Note that you

cannot select “NONE” (Not specified) for

searching.

3 Press (ENTER).

The unit starts searching for a station

broadcasting the selected programme type.

Locating a station by

programme type

You can locate the station you want by

selecting one of the programme types shown

below.

Programme types Display

News NEWS

Current Affairs AFFAIRS

Information INFO

Sports SPORT

Education EDUCATE

Drama DRAMA

Culture CULTURE

Science SCIENCE

Varied VARIED

Popular Music POP M

Rock Music ROCK M

Easy Listening EASY M

Light Classical LIGHT M

Classical CLASSICS

Other Music Type OTHER M

Weather WEATHER

Finance FINANCE

Children’s Programmes CHILDREN

Social Affairs SOCIAL A

Religion RELIGION

Phone In PHONE IN

Travel TRAVEL

Leisure LEISURE

Jazz Music JAZZ

Country Music COUNTRY

National Music NATION M

Oldies Music OLDIES

Folk Music FOLK M

Documentary DOCUMENT

Not specified NONE

Note

You cannot use this function in some countries

where no PTY (Programme Type selection) data is

available.

Страница загружается...

Sony MDX-C6500RX, MDX-C6400R, MDX-C6500R, MDX-C6500RV Инструкция по применению

Похожие модели бренда

Модели других брендов