Vestfrost SW 350 M Instructions For Use Manual

SW ... M

NL Gebruiksaanwijzing

ES Instrucciones para el uso

CZ Návod k použití

PL Instrukcja obsługi

RUS Инструкция по эксплуатации

UK Instructions for use

DE Bedienungsanleitung

FR Mode d’emploi

DK Brugsanvisning

NO Bruksanvisning

Downloaded from Fridge-Manual.com Manuals

2

GB

Thank you for purchasing your new fridge/

freezer from Vestfrost. Please note that

these instructions apply to all fridge/freezers

in the SW range. Illustrations and ttings

may therefore not necessarily correspond

exactly to your model.

Warning

As the refrigerant used in this appliance is a

ammable gas (Isobutane R600a), special

care must be taken to prevent damage

to the refrigerant circuit and piping during

transport and installation.

If damage does occur, avoid sparks or

naked ame in the vicinity of the appliance,

ensure that the room is well ventilated,

disconnect the power supply, and contact

your supplier.

The unit must only be serviced by quali-

ed technicians from an approved service

centre.

Old appliances

Old refrigerators and freezers are often

tted with complicated latches that can

only be opened from the outside. If you

have one of these old units stored away

somewhere, or if you scrap one, remember

to destroy the latch rst in order to prevent

children from being exposed to great dan-

ger by getting locked inside the unit.

Before use

Before operating your new appliance,

please read the following instructions care-

fully as they contain important information

on safety, installation, operation and main-

tenance. Keep the instructions for future

reference.

On receipt, check to ensure that the appli-

ance has not been damaged during trans-

port. Transport damage should be reported

to the local distributor before the appliance

is put to use.

Remove the packaging. Clean the inside of

the cabinet using warm water with a mild

detergent. Rinse with clean water and dry

thoroughly (see cleaning instructions). Use

a soft cloth.

If during transport the appliance has been

laid down, or if it has been stored in cold

surroundings (colder than +5°C), it must be

allowed to stabilise in an upright position for

at least an hour before being switched on.

Contents

Get to know your fridge/freezer........3

Installation and start-up.....................4

Electrical connection.........................6

Reversing the door(s).......................7

Operation and function.....................8

Refrigerator section........................10

Freezer section...............................11

Cleaning and maintenance.............13

Fault nding....................................14

Warranty, spare parts and service..15

Disposal..........................................16

Downloaded from Fridge-Manual.com Manuals

3

GB

Get to know your fridge/freezer

g. 1

Control panel

Lighting

Shelf with storage boxes

Bottle rack

Glass shelf

Door shelf

Large storage box

Nameplate

Crisper bins

Freezing tray

Sealing strip

Freezer drawers

Door handle

Defrost water drain

Kick plate

Adjustable feet

Downloaded from Fridge-Manual.com Manuals

4

GB

Placement

For safety and operational reasons, the

appliance must not be installed outdoors.

The appliance should be placed on a level

surface in a dry, well ventilated room (max.

75% relative air humidity). Never place the

appliance close to sources of heat such as

cookers or radiators, and avoid placing it in

direct sunlight.

Room temperature

The climate class is stated on the

nameplate (see g. 1 on page 3 and g. 13

on page 15). This species the optimum

room temperature.

Climate class Optimum room tem-

perature

SN +10 ºC to +32 ºC

N +16 ºC to +32 ºC

ST +18 ºC to +38 ºC

T +18 ºC to +43 ºC

Installation

The surface on which the appliance is to be

placed must be level. Do not use a frame or

similar.

The appliance can be installed as a free-

standing unit against a wall or built into a

kitchen element (g. 2). If two appliances

are placed side by side, there must be at

least 30 mm clearance between them (g.

3).

After installation, the plug should be

accessible.

600

600 600

30

600

600 600

30

g. 2

g. 3

Installation and start-up

Downloaded from Fridge-Manual.com Manuals

5

GB

Ventilation

It is important that the appliance be well

ventilated and that air can circulate un-

hindered above, below and around it. The

gures below illustrate how the necessary

air circulation can be ensured (gs 6-7).

If two fridge/freezers are placed side by

side, there must be at least 30 mm clear-

ance between them.

1650/1950

100

1560/1860

g. 6

g. 7

The appliance viewed from

above

If the appliance is placed beside a wall,

there must be sufcient room for the freezer

door to be opened wide enough to allow the

drawers to be pulled out (g. 4).

600

610

g. 4

Special considerations for

climate class ST

The distance pieces on the rear of the

appliance ensure sufcient air circulation.

Fit the two caps supplied with the appliance

as shown in g. 5.

g. 5

Downloaded from Fridge-Manual.com Manuals

6

GB

Setting up

It is important that the appliance be

absolutely level. To level the appliance,

remove the kick plate below the door and

screw the adjustable feet up or down (gs

8-9). If necessary, it is possible to adjust the

back feet before the upright is installed. Use

a spirit level to check that the appliance is

absolutely level.

If the appliance is to be placed on a soft

surface, e.g. oorboards or a carpet, it is

best to recheck whether the appliance is still

level after a period of time as the underlying

surface may give under the weight of the

appliance.

g. 8

g. 9

Downloaded from Fridge-Manual.com Manuals

7

GB

The door(s) can be changed from right-hinged to left-hinged and vice versa as follows:

Reversing the door(s)

1. Remove upper hinge. The hinge will be

reused later as the upper hinge on the

opposite side. Lift off upper door.

2. Remove middle hinge. Lift off lower

door. Ret hinge screws.

4. Move hole cover to opposite side of kick

plate and ret kick plate to appliance.

5. Door adjustment (top): Loosen the two

screws holding the upper hinge in place

and turn the hinge to right or left as

required. Retighten the screws.

6. Move handles to opposite side of doors.

Ret plugs in holes on opposite side of

doors.

3. Remove kick plate. Remove lower

hinge by unscrewing the three screws.

Rotate hinge through 180° and ret on

opposite side.

Downloaded from Fridge-Manual.com Manuals

8

GB

The appliance is intended for connection

to alternating current. The required volt-

age (V) and frequency (Hz) are stated on

the nameplate inside the appliance. Power

must be connected via an independent wall

socket outlet.

Technical data

This appliance complies with CE marking

regulations, directives and standards.

Low Voltage Directive 73/23/EEC.

EMC Directive 89/336/EEC.

Council Directive 92/75/EEC on the en-

ergy labelling of household appliances as

subsequently amended by 94/2/EC and

2003/66/EC. Directive 96/57/EC on energy

efciency requirements, and subsequent

amendments.

Electrical connection

Downloaded from Fridge-Manual.com Manuals

9

GB

Refrigerator section

The thermostat button can be set from 1

(min.) to 7 (max.). A suitable setting must be

found by trial and error. Start by setting the

button to 4. Check the temperature, then

adjust the setting upwards or downwards

as required. Usually, a temperature of

5°C is recommended for items stored in

a refrigerator. To check the temperature,

place a thermometer in a glass of water

positioned in the centre of the cabinet for

12 hours. An average temperature of +5°C

should be found in the centre of the cabinet.

Freezer section

Always maintain correct storage

temperature

The thermostat button can be set from 1

(min.) to 7 (max.). A temperature of -18°C

is recommended for items stored in a

freezer. (Maintaining a temperature lower

than this consumes additional energy.) The

temperature in the freezer is displayed on

the thermometer.

- The control lamp lights green when the

power supply is connected correctly.

- The control lamp lights yellow when Super

Freeze is activated.

0

1

2

3

4

5

6

7

Thermostat button, freezer

Lighting

Control lamp

S

O

I

!

Super Freeze

Thermometer

0

1

2

3

4

5

6

7

Thermostat button, refrigerator

Operation and function

g. 10

Downloaded from Fridge-Manual.com Manuals

10

GB

Glass shelves

The shelves are made of tempered glass

and can be repositioned within the cabinet.

To move the shelves, the door must be

opened 90°. To remove a shelf, pull it

forwards and lower it. The shelf can then be

removed and placed in the desired position.

From the top and downwards, the shelves

are suitable for storing bakery products,

ready-made meals, dairy products, meat

products and sliced meat.

Storage boxes

The storage boxes can either be placed

in the door or on the glass shelves. Their

tight-tting lids prevent the products stored

in them from drying out and saves the need

for further packaging. The boxes are ideal

for storing items such as butter and cheese.

The large storage box is ideal for storing

items such as meat and sliced meat.

Bottle rack

The bottle rack is ideal for both large and

small bottles.

Crisper bins

The crisper bins are ideal for storing fruit

and vegetables. The shelf above the bins

functions as a lid, maintaining humidity and

preventing the items stored in the bins from

drying out.

Glass shelf with slide damper

The slide damper above the crisper bins

allows the temperature and humidity in the

bins to be regulated.

- Opening the damper reduces the

temperature and humidity.

- Closing the damper increases the

temperature and humidity.

Shelves in the door

The shelves in the door are practically

positioned with the box shelf at the top, the

egg holder in the middle and door shelves

at the bottom. They provide ample space for

storing large and small bottles, cartons, jars

and tubs. All shelves can be repositioned.

g. 11

g. 12

g. 13

Downloaded from Fridge-Manual.com Manuals

11

GB

Freezer section

The freezer section is a four-star freezer,

approved for freezing and storing foodstuffs.

With the exception of frost-free models, the

freezer is equipped with a practical tray for

freezing loose berries, ice cubes, etc.

Freezing

To keep food at its best, items must be

frozen to -18°C as quickly as possible.

When the Super Freeze button is pressed,

the compressor runs continuously, thus

reducing the temperature as far as possible.

If items weighing 3 kg or more are to be

frozen, the Super Freeze button should

be activated about 24 hours in advance.

To freeze smaller quantities, it is sufcient

to activate Super Freeze just a couple of

hours in advance, or even at the same time

as items are placed in the freezer.

There is no need to use Super Freeze when

pre-frozen items are placed in the freezer or

when small, single items are involved.

The control lamp lights yellow as long

as the Super Freeze function is active.

Remember to switch the Super Freeze

function off again approx. 24 hours after

placing items in the freezer. Otherwise,

the appliance will use more electricity than

necessary.

Only freeze fresh high-quality products.

Meat, poultry, sh, vegetables, fruit, dairy

products and ready-made meals are

suitable for freezing. Items with a high water

content, e.g. lettuce, radishes, grapes,

apples, pears and cucumbers, are not

suitable for freezing.

Pack items to be frozen in airtight

containers, freezer bags or similar. Freeze

items in suitable portions. Do not freeze

vegetables in portions larger than 2.5 kg.

Do not freeze meat in portions larger than

2.5 kg. Keep packages dry to prevent them

from freezing together. To ensure rapid

freezing, make sure, as far as possible,

that items placed in the freezer are not

touching. Ensure that there is as little air

in the packages as possible to prevent the

surfaces of the items from drying out.

Always remember to write the date, content

and quantity on the packages before

placing them in the appliance. It is a good

idea to group items within the freezer. Keep

vegetables in one drawer, meat in another,

and so on.

Thawing

Frozen vegetables and fruit require no

thawing before use and can be immersed in

boiling water direct from the freezer.

To thaw meat, it is advisable to take it out

of the freezer the day before it is to be

used and place it in the refrigerator section

to defrost. This ensures the best hygiene

and maintains meat quality as much as

possible.

Refreezing

If purchased items of frozen food thaw

before reaching home, they must not be

refrozen but should be consumed within

24 hours or cooked immediately and then

frozen.

Frozen items that have been placed in the

refrigerator for thawing may be refrozen

without risk if they have only just thawed.

Note:

Glass bottles or cans containing

carbonated (zzy) drinks must never

be placed in the freezer as they may

explode.

Downloaded from Fridge-Manual.com Manuals

12

GB

4. Remove the items of food. Place them

in the refrigerator or wrap them in

newspaper to keep them as cold as

possible.

5. Place a bowl of hot (but not boiling) water

in the freezer.

6. To prevent the oor from becoming wet

during defrosting, check progress from

time to time and lay towels around the

bowl on the oor to protect against ice

and splashes. When all the frost and

ice have melted, clean the inside of the

cabinet with a mild detergent solution.

Dry the freezer with a soft cloth.

7. Restart the freezer by turning the freezer

thermostat button to the required setting.

If many items are to be returned to the

freezer, activate the Super Freeze button.

Remember to switch Super Freeze off

again.

8. Return items to the freezer approx. 5

minutes after having switched it on.

Automatic defrosting of

refrigerator section

The refrigerator is defrosted automatically.

Defrost water runs through a pipe and is

collected in a tray above the compressor

where the heat generated by the

compressor causes it to evaporate. The

defrost water tray should be cleaned at

intervals.

Defrosting the freezer

The items stored and the humidity of the

air gradually cause frost and ice to form

in the freezer. A thin layer of frost or ice

does not affect freezer performance, but

the thicker the layer, the higher the energy

consumption. Loose frost can be removed

using a plastic or wooden scraper.

Never use a knife or other sharp

implement that might damage the inside

of the freezer.

When the layer of frost and ice exceeds

4-5 mm the freezer should be completely

defrosted.

Proceed as follows:

1. Press the Super Freeze button 4-5

hours before defrosting. This lowers

the temperature of the items stored to

approx. -25°C, thus prolonging the length

of time they remain frozen after having

been removed from the freezer (see step

4 below).

2. Switch the freezer off by turning the

freezer thermostat button to 0.

3. Pull out the drain spout at the bottom of

the cabinet and place a bowl under it to

collect defrost water (g. 11). If the spout

is frozen in place, lay a cloth which has

been soaked in hot water over it for a few

minutes.

Defrosting

g. 11

Downloaded from Fridge-Manual.com Manuals

13

GB

Cleaning

Disconnect the power supply at the mains

socket before cleaning the inside of the

cabinet.

The cabinet is best cleaned using warm wa-

ter (max. 65°C) with a little mild detergent.

Never use cleaning agents that scour. Use

a soft cloth. Rinse with clean water and dry

thoroughly. It is important to prevent water

from entering the control panel.

The defrost water channel, in which

condensation from the evaporator runs, is

located on the rear wall of the cabinet and

must be kept clean. Add a few drops of dis-

infectant, e.g. Rodalon, to the defrost water

drain a couple of times a year, and clean

the drain using a pipe cleaner or similar.

Never use sharp or pointed implements.

The sealing strip around the doors must be

cleaned regularly to prevent discolouration

and prolong service life. Use clean water.

After cleaning the sealing strip, check that it

continues to provide a tight seal.

The condensers need no cleaning. They are

built in, partly to minimise energy consump-

tion, and partly to prevent them from being

damaged.

Dust collecting on the compressor and

in the compressor compartment is best

removed using a vacuum cleaner. It is

possible to clean beneath the appliance by

removing the kick plate.

Stainless steel or aluminium doors are best

cleaned using a care spray and soft cloth.

Various suitable products are available from

most household appliance distributors.

If the appliance is not to be used for any

length of time, switch it off, empty it, clean

the cabinet and ttings, and leave the

door(s) slightly open to allow air circulation

and prevent smells.

Replacing the light bulb

Unscrew the bulb without removing the

shade. Bulbs with an output of more than

12 W must not be used.

Save energy

- Cool hot food and beverages before plac-

ing them in the appliance.

- Thaw frozen items in the refrigerator sec-

tion.

- Keep the door(s) closed as much as pos-

sible.

- Ensure that the door(s) is(are) not pre-

vented from closing tightly.

Cleaning and maintenance

g. 12

Max. 12 W

Downloaded from Fridge-Manual.com Manuals

14

GB

Fault nding

Fault Possible cause Remedy

The control lamp is

not lit.

Power failure; the fuse is blown;

the appliance is not plugged in

correctly.

Check that power is connected.

Reset the fuse.

Water collects on

the glass shelves.

Items of food at the back of the

shelves are in contact with the

evaporator, thus causing conden-

sation to run onto the shelf.

Move the rearmost items for-

wards.

Water collects in the

bottom of the refrig-

erator/freezer.

The defrost water pipe is

blocked.

Clean the defrost water channel

and the drain hole on the rear

wall of the cabinet.

Vibration or bother-

some noise.

The appliance is not level.

The appliance is resting against

other kitchen elements.

Bins, containers or shelves are

not positioned correctly or are

jammed.

Containers or bottles inside the

cabinet are rattling against one

another.

Level the appliance using a spirit

level.

Move the appliance away from

the kitchen elements or appli-

ances it is in contact with.

Check movable ttings and ad-

just them if necessary.

Move containers and/or bottles

apart.

Compressor runs

continuously.

Temperature setting too low.

High room temperature.

Raise the temperature setting.

Ensure adequate ventilation.

Temperature in

freezer too high.

Temperature setting too high.

The quantity of fresh items

placed in the freezer at a time is

greater than the capacity of the

appliance.

Lower the temperature setting.

Wait a few hours and then re-

check the temperature.

Temperature in re-

frigerator too high.

Temperature setting too high.

Many items have been placed

in the refrigerator section at the

same time.

The door is opened too often.

Lower the temperature setting.

Distribute items within the cabi-

net to improve air circulation.

Keep door closed.

Downloaded from Fridge-Manual.com Manuals

15

GB

Warranty disclaimer

Faults and damage caused directly or

indirectly by incorrect operation, misuse,

insufcient maintenance, incorrect building-

in, installation or mains connection, re,

accident, lightening, voltage variation or

other electrical interference, including

defective fuses or faults in mains

installations, or repairs performed by others

than service centres approved by Vestfrost,

and any other faults and damage that the

manufacturer can substantiate are caused

by reasons other than manufacturing or

material faults are not covered by the

warranty.

Transport damage discovered by the buyer

is primarily a matter to be settled between

the buyer and the distributor, i.e. the

distributor must ensure that such complaints

are resolved to the buyer’s satisfaction.

Before calling for technical assistance,

please check whether you are able to rectify

the fault yourself (see Fault nding). If your

request for assistance is unwarranted, e.g.

if the appliance has failed as a result of a

blown fuse or incorrect operation, you will

be charged the costs incurred by your call

for technical assistance.

Spare parts

When ordering spare parts, please state the

type, serial and product numbers of your

appliance (see g. 1 on page 3 and g. 13).

This information is given on the nameplate

inside the cabinet. The nameplate contains

various technical information, including type

and serial numbers.

Note: Always use approved service centres

when your appliance is to be repaired or

replaced!

Service

Vestfrost has local service centres all over

the country who specialise in Vestfrost

products. Here you can obtain xed prices

and professional help for all repairs. Find

your local service centre on www.vestfrost.

dk.

Warranty, spare parts and service

g. 13

Downloaded from Fridge-Manual.com Manuals

16

GB

Environmental regulations on disposal must

also be observed. When disposing of the

appliance you should contact your local

authority technical department who will

inform you of how collection and recycling

of such units take place in your area.

This appliance is marked according to

the European directive 2002/96/EC on

Waste Electrical and Electronic Equipment

(WEEE).

By ensuring this product is disposed of

correctly, you will help prevent potential

negative consequences for the environment

and human health, which could otherwise

be caused by inappropriate waste handling

of this product.

The symbol on the product, or on the

documents accompanying the product,

indicates that this appliance may not be

treated as household waste. Instead it shall

be handed over to the

applicable collection point for the recycling

of electrical and electronic

equipment.

Disposal must be carried out in accordance

with local environmental regulations for

waste disposal.

For more detailed information about

treatment, recovery and recycling of this

product, please contact your local city

ofce, your household waste disposal

service or the shop where you purchased

the product.

Disposal

Downloaded from Fridge-Manual.com Manuals

2

DE

Vielen Dank für Ihre Wahl eines Kühl-

/Gefrierschranks von Vestfrost. Diese

Bedienungsanleitung gilt für alle Kühl- und

Gefrierschränke der SW-Serie. Darum

entsprechen Abbildungen und Ausstattung

nicht in jedem Fall genau Ihrem Gerät.

Warnung

Da ein brennbares Gas (Isobutan R600a)

als Kältemittel dient, ist besondere Vorsi-

cht bei Transport und Installation geboten,

damit kein Teil des Kühlkreislaufs beschä-

digt wird.

Sollte dies dennoch geschehen, vermeiden

Sie Funken und offenes Feuer! Lüften Sie

den Raum gründlich, schalten Sie danach

die Stromzufuhr zum Gerät aus, und wen-

den Sie sich an Ihren Lieferanten.

Wartungs- und Reparaturarbeiten dürfen

nur von einem qualizierten Servicecenter

durchgeführt werden.

Alte Geräte

Alte Kühl- und Gefriergeräte sind häug mit

komplizierten Schnappschlössern verseh-

en, die von innen nicht geöffnet werden

können. Falls bei Ihnen ein solches Gerät

steht, oder wenn Sie ein solches Gerät

ausrangieren, machen Sie bitte zuerst das

Schloss unbrauchbar. So verhindern Sie,

dass spielende Kinder eingesperrt werden

und in Lebensgefahr kommen können.

Vor dem Gebrauch

Vor dem Gebrauch Ihres neuen Geräts

sollten Sie diese Bedienungsanleitung

gründlich lesen. Sie enthält wichtige Infor-

mationen zu Sicherheit, Installation, Betrieb

und Wartung. Bewahren Sie die Bedienung-

sanleitung auf. Sie könnten Sie zu einem

späteren Zeitpunkt evtl. benötigen.

Kontrollieren Sie das Gerät sofort bei

Lieferung auf eventuelle Beschädigungen.

Transportschäden sind dem Händler zu

melden, bevor das Gerät in Gebrauch

genommen wird.

Verpackung entfernen. Das Schrankinnere

mit lauwarmem Wasser und etwas mildem

Spülmittel reinigen. Mit sauberem Wasser

nachwischen und gründlich trocknen (siehe

“Reinigung”). Verwenden Sie ein weiches

Tuch.

Falls das Gerät liegend transportiert wurde

oder einer Temperatur von weniger als +5

°C ausgesetzt war, muss es vor dem Ein-

schalten mindestens eine Stunde lang bei

höherer Außentemperatur aufrecht stehen.

Inhalt

Lernen Sie Ihren

Kühl-/Gefrierschrank kennen............3

Inbetriebnahme und Installation........4

Elektrischer Anschluss......................6

Umschlagen der Tür(en)...................7

Bedienung und Funktion...................8

Kühlteil............................................10

Gefrierteil.........................................11

Reinigung und Wartung..................13

Fehlersuche....................................14

Reklamation,

Ersatzteile und Service...................15

Entsorgung.....................................16

Downloaded from Fridge-Manual.com Manuals

3

DE

Lernen Sie Ihren Kühl-/Gefrierschrank kennen

Abb. 1

Bedienungselemente

Beleuchtung

Einlegeboden mit

Aufbewahrungsbehältern

Flaschenhalter

Glasboden

Türfach

Großer Lagerbehälter

Typenschild

Gemüseschubladen

Gefriertablett

Dichtleiste

Tiefkühlschubladen

Türgriff

Tauwasserabuss

Fußleiste

Einstellbare Füße

Downloaded from Fridge-Manual.com Manuals

4

DE

Aufstellort

Aus Sicherheits- und betriebstechnischen

Gründen darf das Gerät nicht im Freien

aufgestellt werden.

Stellen Sie den Schrank auf einen

ebenen Untergrund in einem trockenen,

gut belüfteten Raum (max. 75 % relative

Luftfeuchtigkeit). Stellen Sie den

Schrank nicht in unmittelbarer Nähe

von Wärmequellen wie Herden oder

Heizkörpern auf, und vermeiden Sie direkte

Sonneneinstrahlung oder Wärme von

anderen Wärmequellen.

Raumtemperatur

Die Klimaklasse nden Sie auf dem

Typenschild (siehe Abb. 1 Seite 3 und Abb.

13 Seite 15). Sie gibt an, innerhalb welcher

Raumtemperaturbereiche der Schrank

optimal arbeitet.

Klimaklasse Zulässige

Raumtemperatur

SN +10 ºC bis +32 ºC

N +16 ºC bis +32 ºC

ST +18 ºC bis +38 ºC

T +18 ºC bis +43 ºC

Installation

Die Unterlage zum Aufstellen des Schranks

muss eben sein. Verwenden Sie keinen

Rahmen o.ä.

Der Schrank kann frei an einer Wand

stehen oder in ein Küchenelement

eingebaut werden (Abb. 2). Bei Aufstellung

neben anderen Möbeln müssen mindestens

30 mm Luft um den Schrank herum frei

bleiben. (Abb. 3). Nach der Installation

muss der Stecker zugänglich sein.

600

600 600

30

600

600 600

30

Abb. 2

Abb. 3

Inbetriebnahme und Installation

Downloaded from Fridge-Manual.com Manuals

5

DE

Belüftung

Achtung: Der Schrank muss ausreichend

belüftet sein, und die Luftzirkulation über

und unter ihm sowie seitlich vom Schrank

darf nicht behindert sein. Die folgenden

Abbildungen zeigen, wie die erforderliche

Belüftung in der direkten Umgebung des

Schranks sicherzustellen ist (Abb. 6-7).

Bei Aufstellung zweier Kühl-/

Gefrierschränke nebeneinander ist ein

Mindestabstand von 30 mm einzuhalten.

1650/1950

100

1560/1860

Abb. 6 Abb. 7

Schrank in Draufsicht

Wird der Schrank neben einer Wand

aufgestellt, ist darauf zu achten, soviel

Platz zu lassen, dass die Tür(en) zum

HerauSWiehen der Tiefkühlschubladen weit

genug geöffnet werden können (Abb. 4).

600

610

Abb. 4

Besondere Umstände

bezüglich der Klimaklasse ST

Die Abstandsstücke auf der Rückseite

des Schranks sichern die erforderliche

Luftzirkulation. Die beiden Abdeckungen

montieren, die zusammen mit dem Schrank

mitgeliefert werden (siehe Abb. 5).

Abb. 5

Downloaded from Fridge-Manual.com Manuals

Страница загружается...

Vestfrost SW 350 M Instructions For Use Manual

Похожие модели бренда

Модели других брендов