Pioneer GM-D8601 Руководство пользователя

Категория
Усилители звука для автомобилей
Тип
Руководство пользователя

Это руководство также подходит для

Owner’s Manual
Mode d’emploi
Manuale d’istruzioni
Manual de instrucciones
Bedienungsanleitung
Handleiding
Руководство пользователя
CLASS D MONO AMPLIFIER
AMPLIFICATEUR MONO DE CLASSE D
AMPLIFICATORE MONOFONICO DI CLASSE D
AMPLIFICADOR MONO DE LA CLASE D
MONOVERSTÄRKER DER KLASSE D
MONOVERSTERKER KLASSE D
МОНОФОНИЧЕСКИЙ УСИЛИТЕЛЬ КЛАССА D
English Nederlands
Русский
Français Italiano Español Deutsch
GM-D8601
GM-D9601
 
Thank you for purchasing this PIONEER
product
To ensure proper use, please read through this
manual before using this product. It is espe-
cially important that you read and observe
WARNINGs and CAUTIONs in this manual.
Please keep the manual in a safe and accessible
place for future reference.
If you want to dispose this product, do not mix
it with general household waste. There is a se-
parate collection system for used electronic
products in accordance with legislation that re-
quires proper treatment, recovery and recy-
cling.
Private households in the member states of
the EU, in Switzerland and Norway may return
their used electronic products free of charge
to designated collection facilities or to a retai-
ler (if you purchase a similar new one).
For countries not mentioned above, please
contact your local authorities for the correct
method of disposal.
By doing so you will ensure that your disposed
product undergoes the necessary treatment,
recovery and recycling and thus prevent po-
tential negative effects on the environment
and human health.
Visit our website
Visit us at the following site:
http://www.pioneer.co.uk
! Register your product. We will keep the de-
tails of your purchase on file to help you
refer to this information in the event of an
insurance claim such as loss or theft.
! We offer the latest information about
PIONEER CORPORATION on our
website.
If you experience problems
Should this product fail to operate properly,
please contact your dealer or nearest author-
ized Pioneer Service Station.
About This Product
This product is a mono amplifier for subwoofer. If
both L (left) and R (right) channels are connected
to the RCA input of this product, output is mixed
because this product is a mono amplifier.
Before connecting/
installing the amplifier
WARNING
! This unit is for vehicles with a 12 V battery and
negative grounding. Before installing in re-
creational vehicles, trucks or buses, check the
battery voltage.
! When installing this unit, make sure to con-
nect the ground wire first. Ensure that the
ground wire is properly connected to metal
parts of the cars body. The ground wire of the
one of this unit must be connected to the car
separately with different screws. If the screw
for the ground wire loosens or falls out, it
could result in fire, generation of smoke or
malfunction.
! Be sure to install the fuse to the battery wire.
! Always use a fuse of the rating prescribed.
The use of an improper fuse could result in
overheating and smoke, damage to the pro-
duct and injury, including burns.
! Check the connections of the power supply
and speakers if the fuse of the separately sold
battery wire or the amplifier fuse blows. Deter-
mine and resolve the cause, then replace the
fuse with and identical equivalent.
En
2
Section
01
Before you start
! Always install the amplifier on a flat surface.
Do not install the amplifier on a surface that
is not flat or on a surface with a protrusion.
Doing so could result in malfunction.
! When installing the amplifier, do not allow
parts such as extra screws to get caught be-
tween the amplifier and the automobile.
Doing so could cause malfunction.
! Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, damage to this unit, smoke, and over-
heating could result from contact with liquids.
The surfaces of the amplifier and any attached
speakers may also heat up and cause minor
burns.
! In the event of any abnormality, the power
supply to the amplifier is cut off to prevent
equipment malfunction. If this occurs, switch
the system power off and check the power
supply and speaker connections. If you are un-
able to determine the cause, please contact
your dealer.
! Always disconnect the negative * terminal of
the battery beforehand to avoid the risk of
electric shock or short circuit during installa-
tion.
! Do not attempt to disassemble or modify this
unit. Doing so may result in fire, electric
shock or other malfunction.
CAUTION
! Always keep the volume low enough to hear
outside sounds.
! Extended use of the car stereo while the en-
gine is at rest or idling may exhaust the bat-
tery.
! Connect either of three subwoofers to the am-
plifier; 1: a subwoofer with a 300 W (GM-
D8601) / 500 W (GM-D9601) or larger nominal
input and an impedance 4 W, 2: a subwoofer
with a 500 W (GM-D8601) / 800 W (GM-D9601)
or larger nominal input and an impedance 2 W
or 3: a subwoofer with a 800 W (GM-D8601) /
1 200W (GM-D9601) or larger nominal input
and an impedance 1 W.
If the nominal input and impedance are out of
the above ranges, the subwoofer may catch
fire, emit smoke or become damaged.
About the protection function
This product has protection function. When this
product detects something abnormal, the follow-
ing functions will operate to protect the product
and speaker output.
! The POWER/PROTECT indicator will turn red
and the amplifier will shut down in the situa-
tions outlined below.
If the temperature inside the amplifier gets
too high.
If a DC voltage is applied to the speaker
output terminal.
! The POWER/PROTECT indicator will turn red
and the output will be muted in the situations
outlined below.
If the speaker output terminal and speaker
wire are short-circuited.
En
3
English
Section
01
Before you start
Whats what
GM-D8601
Front side
21 3 4
Rear side
GM-D9601
Front side
21 3 4
Rear side
To adjust the switch, use a flathead screwdri-
ver if needed.
1 POWER/PROTECT indicator
The power indicator lights up to indicate
power ON.
! If something is not normal, the indicator
turns red.
2 GAIN (gain) control
If output remains low, even when the car
stereo volume is turned up, turn controls to
lower level. If distortion occurs when the car
stereo volume is turned up, turn these con-
trols to higher level.
! For use with an RCA equipped car stereo
(standard output of 500 mV), set to the
NORMAL position. For use with an RCA
equipped Pioneer car stereo, with maxi-
mum output of 4 V or more, adjust level
to match that of the car stereo output.
! For use with an RCA equipped car stereo
with output of 4 V, set to the H position.
! If you hear too much noise when using
the speaker input terminals, turn the
gain control to higher level.
3 LPF (low-pass filter) cut off frequency
control
You can select a cut off frequency from
40 Hz to 240 Hz.
4 BASS BOOST REMOTE (bass boost level
remote control) jack
By connecting the Bass boost level remote
control to the jack on the main unit, you will
be able to select a bass boost level from
0 dB to 18 dB.
For instruction of connecting the bass boost
remote control to the amplifier, see the Con-
nection diagram on page 6.
Setting gain properly
! Protective function included to prevent
malfunction of the unit and/or speakers
due to excessive output, improper use or
improper connection.
! When outputting high volume sound etc.,
this function cuts off the output for a few
seconds as a normal function, but output
is restored when the volume of the head
unit is turned down.
En
4
Section
02
Setting the unit
! A cut in sound output may indicate impro-
per setting of the gain control. To ensure
continuous sound output with the head
unit at a high volume, set amplifier gain
control to a level appropriate for the preout
maximum output level of the head unit, so
that volume can remain unchanged and to
control excess output.
! Despite correct volume and gain settings,
the unit sound still cuts out periodically. In
such cases, please contact the nearest
authorized Pioneer Service Station.
Gain control of this unit
Preout level: 2V (Standard: 500 mV)
Preout level: 4V
Above illustration shows NORMAL gain set-
ting.
Relationship between amplifier gain
and head unit output power
If amplifier gain is raised improperly, this will
simply increase distortion, with little increase
in power.
Signal waveform when outputting at
high volume using amplifier gain
control
Signal waveform distorted with high output, if
you raise the gain of the amplifier the power
changes only slightly.
En
5
English
Section
02
Setting the unit
Connection diagram
h
2
a
9
8
6
7
3
b
c
d
5
j
i
f
g
e
4
1
1 Battery wire (sold separately)
! The maximum length of the wire be-
tween the fuse and the positive + term-
inal of the battery is 30 cm.
! For the wire size, refer to Connecting the
power terminal on page 8. The battery
wire, the ground wire and the optional
direct ground wire must be same size.
After making all other connections at
the amplifier, connect the battery wire
terminal of the amplifier to the positive
+ terminal of the battery.
2 Fuse 100 A (GM-D8601) / 150 A (GM-D9601)
(sold separately)
Each amplifier must be separately fused at
100 A (GM-D8601) / 150 A (GM-D9601).
3 Positive (+) terminal
4 Negative (*) terminal
5 Battery (sold separately)
6 Ground wire, Terminal (sold separately)
The ground wires must be same size as the
battery wire.
Connect to metal body or chassis.
7 Car stereo with RCA output jacks (sold sepa-
rately)
8 External output
9 Connecting wire with RCA pin plugs (sold se-
parately)
a Amplifier with RCA input jacks (sold sepa-
rately)
b Bass boost level remote control
c Bass boost level remote control wire (5 m)
d RCA input jack
e RCA output jack
f System remote control wire (sold separately)
Connect male terminal of this wire to the sys-
tem remote control terminal of the car stereo.
The female terminal can be connected to the
auto-antenna relay control terminal. If the car
stereo lacks a system remote control terminal,
connect the male terminal to the power term-
inal via the ignition switch.
g Speaker output terminals
Please see the following section for speaker
connection instructions. Refer to Connections
when using the speaker input wire on page 8.
h Fuse 40 A × 2 (GM-D8601) / 40 A × 3 (GM-
D9601)
i Front side
j Rear side
Before connecting the
amplifier
WARNING
! Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap sections
in contact with metal parts in adhesive tape.
! Never cut the insulation of the power supply
to feed power to other equipment. Current ca-
pacity of the wire is limited.
CAUTION
! Never shorten any wires, the protection circuit
may malfunction.
! Never wire the speaker negative cable directly-
to ground.
En
6
Section
03
Connecting the units
! Never band together multiple speakers nega-
tive cables.
! If the system remote control wire of the ampli-
fier is connected to the power terminal via the
ignition switch (12 V DC), the amplifier will re-
main on with the ignition whether the car
stereo is on or off, which may exhaust battery
if the engine is at rest or idling.
! Install and route the separately sold battery
wire as far as possible from the speaker wires.
Install and route the separately sold battery
wire, ground wire, speaker wires and the am-
plifier as far away as possible from the anten-
na, antenna cable and tuner.
Connecting the speakers
This amplifier can be connected to two speak-
ers in parallel. Connect the speaker leads to
suit the mode according to the figure shown
below.
Precautions for parallel connection
! When wiring two speakers in parallel, make
sure that the synthetic impedance is from
1 W to 8 W to prevent the amplifier from
catching fire, generating smoke and/or
being damaged.
! When connected in parallel with the syn-
thetic impedance less than 1 W, as a nor-
mal function, this amplifier may
automatically be set on mute if outputting
high volume sound. Turn down the volume
until the mute function is canceled.
When connecting to one speaker
Speaker output
When connecting to two speakers
The output from two speakers is the same as
that of one speaker.
Speaker output
En
7
English
Section
03
Connecting the units
Connections when using
the speaker input wire
Connect the car stereo speaker output wires
to the amplifier using the supplied speaker
input wire with RCA pin cord.
1 Car Stereo
2 Speaker output
3 Red: Right +
4 Black: Right *
5 Black: Left *
6 White: Left +
7 Speaker input wire with RCA pin cord
To the RCA input jack of this unit
Notes
! If speaker wires with an RCA pin cord from a
headunit are connected to this amplifier, the
amplifier will automatically turn on when the
headunit is turned on. When the headunit is
turned off, the amplifier turns off automati-
cally. This function may not work with some
headunits. In such cases, please use a sys-
tem remote control wire (sold separately). If
multiple amplifiers are to be connected to-
gether synchronously, connect the head unit
and all amplifiers via the system remote con-
trol wire.
! Connect the system remote control wire when
you wish to only turn on the car stereo, not the
amplifier.
! This amplifier automatically selects an input
signal mode between the RCA level and the
speaker level by detecting an input signal.
Solderless terminal
connections
! Since the wire will become loose over time,
it must be periodically inspected and tigh-
tened as necessary.
! Do not solder or bind the ends of the
twisted wires.
! Fasten while making sure to not to clamp
the insulating sheath of the wire.
! Use the supplied hexagonal wrench to
tighten and loosen the terminal screw of
the amplifier and use it to securely fasten
the wire. Be careful to avoid excessive tigh-
tening of this screw, which may damage
the wire.
Connecting the power terminal
WARNING
If the battery wire is not securely fixed to the term-
inal using the terminal screws, there is a risk of
overheating, malfunction and injury, including
minor burns.
! Always use the recommended battery and
ground wire, which is sold separately. Con-
nect the battery wire directly to the car bat-
tery positive (+) terminal and the ground
wire to the car body.
! Recommended wires size (AWG: American
Wire Gauge) is as follows. The battery wire,
the ground wire and the optional direct
ground wire must be same size.
! Use a wire of 8 AWG to 16 AWG wire for the
speaker wire.
Battery wire and ground wire size
Wire length Wire size
less than 3.6 m 6 AWG
less than 6.4 m 4 AWG
En
8
Section
03
Connecting the units
1 Route battery wire from engine com-
partment to the vehicle interior.
! When drilling a cable pass-hole into the ve-
hicle body and routing a battery wire thor-
ough it, take care not to short-circuit the
wire damaging it by the cut edges or burrs
of the hole.
After completing all other amplifier connec-
tions, finally connect the battery wire terminal
of the amplifier to the positive (+) battery
terminal.
2
1
3
1 Positive (+) terminal
2 Battery wire (sold separately)
The maximum length of the wire between
the fuse and the positive + terminal of the
battery is 30 cm.
3 Fuse 100 A (GM-D8601) / 150 A (GM-D9601)
(sold separately)
Each amplifier must be separately fused at
100 A (GM-D8601) / 150 A (GM-D9601).
2 Use wire cutters or a utility knife to
strip the end of the battery wire, ground
wire and system remote control wire to ex-
pose about 10 mm of the end of each of
the wires, and then twist the exposed ends
of the wires.
Twist
10 mm
3 Connect the wires to the terminal.
Fix the wires securely with the terminal
screws.
3
6
1
5
4
2
7
1 Battery wire
2 Power terminal
3 Ground wire
4 GND terminal
5 System remote control wire
6 System remote control terminal
7 Terminal screws
Connecting the speaker output
terminals
1 Use wire cutters or a utility knife to
strip the end of the speaker wires to ex-
pose about 10 mm of wire and then twist
the wire.
Twist
10 mm
2 Connect the speaker wires to the
speaker output terminals.
Fix the wires securely with the terminal
screws.
1
3
2
1 Terminal screws
2 Speaker wires
3 Speaker output terminals
En
9
English
Section
03
Connecting the units
Before installing the amplifier
WARNING
! To ensure proper installation, use the supplied
parts in the manner specified. If any parts
other than those supplied are used, they may
damage internal parts of the amplifier, or be-
come loose causing the amplifier to shut
down.
! Do not install in:
Places where it could injure the driver or
passengers if the vehicle stops suddenly.
Places where it may interfere with the dri-
ver, such as on the floor in front of the dri-
vers seat.
! Install tapping screws in such a way that the
screw tip does not touch any wire. This is im-
portant to prevent wires from being cut by vi-
bration of the car, which can result in fire.
! Make sure that wires do not get caught in the
sliding mechanism of the seats or touch the
legs of a person in the vehicle as short-circuit
may result.
! When drilling to install the amplifier, always
confirm no parts are behind the panel and
protect all cables and important equipment
(e.g. fuel/brake lines, wiring) from damage.
CAUTION
! To ensure proper heat dissipation of the ampli-
fier, ensure the following during installation:
Allow adequate space above the amplifier
for proper ventilation.
Do not cover the amplifier with a floor mat
or carpet.
! Place all cables away from hot places, such
as near the heater outlet.
! The optimal installation location differs de-
pending on the car model. Secure the ampli-
fier at a sufficiently rigid location.
! Check all connections and systems before
final installation.
! After installing the amplifier, confirm that the
spare tire, jack and tools can be easily re-
moved.
Attaching the Bass boost
remote control
Attach with tapping screws (3 mm × 10 mm)
at an easily accessible location such as under
the dashboard.
Tapping screws (3mm × 10 mm)
Example of insta llation on
the floor mat or chassis
1 Place the amplifier in the desired instal-
lation location.
Insert the supplied tapping screws (4 mm ×
18 mm) into the screw holes and push on the
screws with a screwdriver so they make an im-
print where the installation holes are to be lo-
cated.
2 Drill 2.5 mm diameter holes at the im-
prints either on the carpet or directly on
the chassis.
En
10
Section
04
Installation
3 Install the amplifier with the use of
supplied tapping screws (4 mm × 18 mm).
1
2
3
45
1 Tapping-screws (4 mm × 18 mm)
2 Drill a 2.5 mm diameter hole
3 Floor mat or chassis
4 Hole-to-hole distance: 257 mm (GM-D8601)
/ 307 mm (GM-D9601)
5 Hole-to-hole distance: 181 mm (GM-D8601)
/ 181 mm (GM-D9601)
En
11
English
Section
04
Installation
Specifications
GM-D8601
Power source ............................. 14.4 V DC (10.8 V to 15.1 V
allowable)
Grounding system ................... Negative type
Current consumption ............ 24 A (at continuous power,
4 W)
Average current drawn ......... 2.9 A (4 W for one channel)
4.0 A (2 W for one channel)
6.0 A (1 W for one channel)
Fuse ................................................ 40 A × 2
Dimensions (W × H × D) ... 265 mm × 60 mm ×
200 mm
Weight .......................................... 2.7 kg (Leads for wiring not
included)
Maximum power output ....... 600 W × 1 (4 W)/1600
1(1W)
Continuous power output ... 300 W × 1 (at 14.4 V, 4 W,
20 Hz to 240 Hz, 1 % THD)
500 W × 1 (at 14.4 V, 2 W,
100 Hz, 1 % THD)
800 W × 1 (at 14.4 V, 1 W,
100 Hz, 1 % THD)
Load impedance ...................... 4 W (1 W to 8 W allowable)
Frequency response ............... 10 Hz to 240Hz (+0 dB,
3 dB)
Signal-to-noise ratio ............... 100 dB (IEC-A network)
Low pass filter:
Cut off frequency ........... 40 Hz to 240 Hz
Cut off slope ..................... 12 dB/oct
Bass boost:
Frequency .......................... 50 Hz
Level ..................................... 0dBto18dB
Gain control:
RCA ...................................... 200 mV to 6.5 V
Speaker .............................. 0.8 V to 16 V
Maximum input level / impedance:
RCA ...................................... 6.5 V / 25 kW
Speaker .............................. 16 V / 12 kW
GM-D9601
Power source ............................. 14.4 V DC (10.8 V to 15.1 V
allowable)
Grounding system ................... Negative type
Current consumption ............ 39 A (at continuous power,
4 W)
Average current drawn ......... 3.7 A (4 W for one channel)
5.2 A (2 W for one channel)
7.5 A (1 W for one channel)
Fuse ................................................ 40 A × 3
Dimensions (W × H × D) ... 315 mm × 60 mm ×
200 mm
Weight .......................................... 3.3 kg (Leads for wiring not
included)
Maximum power output ....... 1 000 W × 1 (4 W) / 2 400 W
×1(1W)
Continuous power output ... 500 W × 1 (at 14.4 V, 4 W,
20 Hz to 240 Hz, 1 % THD)
800 W × 1 (at 14.4 V, 2 W,
100 Hz, 1 % THD)
1 200 W × 1 (at 14.4 V, 1 W,
100 Hz, 1 % THD)
Load impedance ...................... 4 W (1 W to 8 W allowable)
Frequency response ............... 10 Hz to 240Hz (+0 dB,
3 dB)
Signal-to-noise ratio ............... 100 dB (IEC-A network)
Low pass filter:
Cut off frequency ........... 40 Hz to 240 Hz
Cut off slope ..................... 12 dB/oct
Bass boost:
Frequency .......................... 50 Hz
Level ..................................... 0dBto18dB
Gain control:
RCA ...................................... 200 mV to 6.5 V
Speaker .............................. 0.8 V to 16 V
Maximum input level / impedance:
RCA ...................................... 6.5 V / 25 kW
Speaker .............................. 16 V / 12 kW
Notes
! Specifications and the design are subject to
modifications without notice.
! The average current drawn is nearly the maxi-
mum current drawn by this unit when an
audio signal is input. Use this value when
working out total current drawn by multiple
power amplifiers.
En
12
Appendix
Additional information
Nous vous remercions davoir acheté cet
appareil PIONEER.
Pour garantir une utilisation correcte, lisez
bien ce mode demploi avant dutiliser cet ap-
pareil. Il est particulièrement important que
vous lisiez et respectiez les indications AT-
TENTION et PRÉCAUTION de ce mode
demploi. Conservez-le dans un endroit sûr et
facilement accessible pour toute consultation
ultérieure.
Si vous souhaitez vous débarrasser de cet ap-
pareil, ne le mettez pas à la poubelle avec vos
ordures ménagères. Il existe un système de
collecte séparé pour les appareils électroni-
ques usagés, qui doivent être récupérés, traités
et recyclés conformément à la législation.
Dans les états membres de lUE, en Suisse et
en Norvège, les foyers domestiques peuvent
rapporter leurs produits électroniques usagés
gratuitement à des points de collecte spécifiés
ou à un revendeur (sous réserve dachat dun
produit similaire).
Dans les pays qui ne sont pas mentionnés ci-
dessus, veuillez contacter les autorités locales
pour vous informer de la méthode correcte de
mise au rebut.
En agissant ainsi vous assurerez que le pro-
duit que vous mettez au rebut est soumis au
processus de traitement, de récupération et
de recyclage nécessaire et éviterez ainsi les ef-
fets négatifs potentiels sur lenvironnement et
la santé publique.
Visitez notre site Web
Rendez-nous visite sur le site suivant :
http://www.pioneer.fr
! Enregistrez votre produit. Nous conserve-
rons les détails de votre achat dans nos fi-
chiers pour vous aider à faire référence à
ces informations pour une déclaration das-
surance en cas de perte ou de vol.
! Notre site Web fournit les informations les
plus récentes sur PIONEER
CORPORATION.
Si vous rencontrez des
problèmes
En cas danomalie, consultez le distributeur
ou le service dentretien agréé par Pioneer le
plus proche.
Quelques mots sur cet appareil
Ce produit est un amplificateur mono pour haut-
parleur dextrêmes graves. Si les canaux L (gau-
che) et D (droit) sont tous les deux connectés à
lentrée RCA de ce produit, la sortie sera combi-
née étant donné que ce produit est un amplifica-
teur mono.
Avant de connecter/
dinstaller lamplificateur
ATTENTION
! Cet appareil est utilisable sur des véhicules
équipés dune batterie 12 V avec mise à la
masse du négatif. Vérifiez la tension de la bat-
terie avant linstallation dans des véhicules de
caravaning, des camions ou des bus.
Fr
13
Section
Français
01
Avant de commencer
! Lors de linstallation de cet appareil, veillez à
connecter dabord le fil de masse. Assurez-
vous que le fil de masse est connecté correc-
tement aux parties métalliques de la carrosse-
rie du véhicule. Le fil de masse de cet appareil
doit être connecté indépendamment au véhi-
cule à laide de vis différentes. Si la vis du fil
de masse se desserre ou tombe, il peut en ré-
sulter un incendie, de la fumée ou un dysfonc-
tionnement.
! Assurez-vous de bien installer le fusible sur le
fil de la batterie.
! Utilisez toujours un fusible correspondant aux
caractéristiques spécifiées. Lutilisation dun
fusible incorrect peut entraîner une sur-
chauffe et de la fumée, des dommages au ni-
veau du produit et des blessures, incluant des
brûlures.
! Vérifiez les connexions de lalimentation et
des haut-parleurs en cas de rupture du fusible
du fil de batterie vendu séparément ou de
lamplificateur. Déterminez la cause et résol-
vez le problème, puis remplacez le fusible par
un fusible identique.
! Installez toujours lamplificateur sur une sur-
face plane. Ninstallez pas lamplificateur sur
une surface qui nest pas plane ou sur une
sur face présentant une saillie. Ceci pourrait
entraîner un dysfonctionnement.
! Lors de linstallation de lamplificateur, ne lais-
sez pas des pièces telles que des vis supplé-
mentaires se coincer entre lamplificateur et
lautomobile. Ceci pourrait entraîner un dys-
fonctionnement.
! Ne laissez pas cet appareil entrer en contact
avec des liquides. Cela pourrait provoquer une
électrocution. Tout contact avec des liquides
pourrait aussi provoquer des dommages, de
la fumée et une surchauffe de lappareil.
Les surfaces de lamplificateur et des haut-
parleurs connectés peuvent également chauf-
fer et entraîner des brûlures mineures.
! En cas dévénement anormal, lalimentation
de lamplificateur est coupée de manière à évi-
ter tout dysfonctionnement de léquipement.
Dans ce cas, coupez lalimentation du sys-
tème et vérifiez les connexions de lalimenta-
tion et des haut-parleurs. Si vous nêtes pas
en mesure de déterminer la cause, veuillez
contacter votre revendeur.
! Déconnectez toujours la borne négative * de
la batterie préalablement, de manière à éviter
tout risque de choc électrique ou de court-cir-
cuit lors de linstallation.
! Nessayez pas de démontez ou de modifiez
cet appareil. Ceci pourrait provoquer un in-
cendie, une électrocution ou tout autre dys-
fonctionnement.
PRÉCAUTION
! Maintenez le niveau découte à une valeur
telle que vous puissiez entendre les sons pro-
venant de lextérieur.
! Lutilisation prolongée du système stéréo du
véhicule lorsque le moteur est à larrêt ou au
ralenti peut épuiser la batterie.
! Connectez lun des trois haut-parleurs dextrê-
mes graves à lamplificateur ; 1 : un haut-par-
leur dextrêmes graves avec une entrée
nominale de 300 W (GM-D8601) / 500 W (GM-
D9601) ou plus et une impédance de 4 W;2:
un haut-parleur dextrêmes graves avec une
entrée nominale de 500 W (GM-D8601) / 800 W
(GM-D9601) ou plus et une impédance de 2 W
ou 3 : un haut-parleur dextrêmes graves avec
une entrée nominale de 800 W (GM-D8601) /
1 200 W (GM-D9601) ou plus et une impé-
dance de 1 W.
Si lentrée nominale et limpédance sont en
dehors des plages ci-dessus, le haut-parleur
dextrêmes graves risque de prendre feu, de
dégager de la fumée ou dêtre endommagé.
Quelques mots sur la fonction de
protection
Ce produit est doté dune fonction de protection.
Lorsque ce produit détecte une anomalie, les
fonctions suivantes permettent de protéger le
produit et la sortie du haut-parleur.
! Lindicateur POWER/PROTECT devient rouge
et lamplificateur se met hors service dans les
situations indiquées ci-dessous.
Fr
14
Section
01
Avant de commencer
Si la température à lintérieur de lamplifi-
cateur est trop élevée.
Si une tension CC est appliquée à la borne
de sortie des haut-parleurs.
! Lindicateur POWER/PROTECT devient rouge
et le son de la sortie est coupé dans les situ-
ations indiquées ci-dessous.
Si la borne de sortie des haut-parleurs et le
fil du haut-parleur sont en court-circuit.
Fr
15
Section
Français
01
Avant de commencer
Description de lappareil
GM-D8601
Face avant
21 3 4
Face arrière
GM-D9601
Face avant
21 3 4
Face arrière
Si nécessaire, utilisez un tournevis plat pour
régler le commutateur.
1 Indicateur POWER/PROTECT
Lindicateur de mise sous tension sallume
pour indiquer la mise sous tension.
! Lindicateur devient rouge en cas dano-
malie.
2 Commande GAIN (gain)
Si la sortie reste faible alors que le volume
du système stéréo du véhicule a été aug-
menté, tournez les commandes vers un ni-
veau plus faible. En cas de distorsion lors
de laugmentation du volume du système
stéréo du véhicule, tournez les commandes
vers un niveau plus élevé.
! Procédez au réglage sur la position
NORMAL pour lutilisation avec un sys-
tème stéréo de véhicule équipé dune
sortie RCA (sortie standard de 500 mV).
Pour lutilisation avec un système stéréo
de véhicule Pioneer équipé dune sortie
RCA, dont la sortie maximale est de 4 V
ou plus, réglez le niveau en fonction de
celui de sortie du système stéréo du véhi-
cule.
! Procédez au réglage sur la position H
pour lutilisation avec un système stéréo
de véhicule équipé dune sortie de 4 V.
! Si la quantité de parasites est trop impor-
tante lors de lutilisation des bornes den-
trée des haut-parleurs, tournez la
commande de gain à un niveau plus
élevé.
3 Commande de fréquence de coupure
LPF (filtre passe-bas)
Vous pouvez sélectionner une fréquence de
coupure de 40 Hz à 240 Hz.
4 Jack BASS BOOST REMOTE (télécom-
mande du niveau daccentuation des gra-
ves)
En connectant la télécommande du niveau
daccentuation des graves au jack de lappa-
reil central, vous pourrez sélectionner le ni-
veau daccentuation de graves entre 0 dB et
18 dB.
Pour des instructions sur la connexion de la
télécommande du niveau daccentuation
des graves à lamplificateur, reportez-vous à
la page 18, Schéma de connexion.
Fr
16
Section
02
Réglage de lappareil
Réglage correct du gain
! Fonction de protection incluse pour éviter
tout dysfonctionnement de lappareil et/ou
des haut-parleurs lié à une sortie excessive
ou à une utilisation ou une connexion in-
correcte.
! Lors de lémission de sons à haut volume,
etc., cette fonction coupe lémission pen-
dant quelques secondes. Lémission est ce-
pendant rétablie une fois le volume de
lappareil central baissé.
! Une coupure de la sortie son peut indiquer
un réglage incorrect de la commande de
gain. Afin de garantir une émission sonore
continue lorsque le volume de lappareil
central est élevé, réglez la commande de
gain de lamplificateur à un niveau adapté
au niveau de sortie maximal de la sortie
préamp de lappareil central de manière à
ce que le volume ne nécessite aucune mo-
dification et à ce que les sorties excessives
soient contrôlées.
! Le son de lappareil est régulièrement
coupé alors que les réglages du gain et du
volume sont corrects. Dans de tels cas,
veuillez contacter le Centre d entretien
agréé par Pioneer le plus proche.
Commande de gain de lappareil
Niveau de préamp : 2 V (standard : 500 mV)
Niveau de préamp : 4 V
Lillustration ci-dessus représente le réglage
de gain NORMAL.
Relation entre le gain de
lamplificateur et la puissance de
sortie de lappareil central
Si le gain de lamplificateur est augmenté de
manière incorrecte, les distorsions augmen-
tent sans que la puissance soit beaucoup plus
importante.
Forme de signal lors de lémission à
volume élevé avec la commande de
gain de lamplificateur
Forme de signal distordu avec sortie élevée, si
vous augmentez le gain de lamplificateur, la
puissance nest que légèrement modifiée.
Fr
17
Section
Français
02
Réglage de lappareil
Schéma de connex ion
h
2
a
9
8
6
7
3
b
c
d
5
j
i
f
g
e
4
1
1 Fil de la batterie (vendu séparément)
! La longueur maximale du fil entre le fu-
sible et la borne positive + de la batterie
est de 30 cm.
! Pour connaître la taille du fil, reportez-
vous à la page 20, Connexion de la borne
dalimentation. Le fil de la batterie, le fil
de terre et le fil de terre directe en option
doivent être de la même taille. Une fois
toutes les autres connexions à lamplifi-
cateur effectuées, connectez la borne
du fil de la batterie de lamplificateur à
la borne positive + de la batterie.
2 Fusible 100 A (GM-D8601) / 150 A (GM-D9601)
(vendu séparément)
Chaque amplificateur doit être doté dun fu-
sible distinct de 100 A (GM-D8601) / 150 A
(GM-D9601).
3 Borne positive (+)
4 Borne négative (*)
5 Batterie (vendue séparément)
6 Fil de terre, borne (vendu séparément)
Les fils de terre doivent être de la même taille
que le fil de la batterie.
À connecter au châssis ou à la carrosserie en
métal.
7 Système stéréo de véhicule avec jacks de sor-
tie RCA (vendu séparément)
8 Sortie externe
9 Fil de connexion avec prises RCA (vendu sépa-
rément)
a Amplificateur avec jacks dentrée RCA (vendu
séparément)
b Télécommande du niveau daccentuation des
graves
c Fil de la télécommande du niveau daccentua-
tion des graves (5 m)
d Jack dentrée RCA
e Jack de sortie RCA
f Fil de la télécommande du système (vendu sé-
parément)
Connectez la borne mâle du fil à la borne de
la télécommande du système stéréo du véhi-
cule. La borne femelle peut être connectée à
la prise de commande du relais de lantenne
motorisée. Si le système stéréo du véhicule ne
dispose pas dune borne de télécommande,
connectez la borne mâle à la borne dalimen-
tation via le contact dallumage.
g Bornes de sortie des haut-parleurs
Veuillez vous reporter à la section suivante
pour les instructions de connexion des haut-
parleurs. Reportez-vous à la page 20, Conne-
xions lors de lutilisation du fil dentrée des
haut-parleurs.
h Fusible 40 A × 2 (GM-D8601) / 40 A × 3 (GM-
D9601)
i Face avant
j Face arrière
Avant de connecter
lamplificateur
ATTENTION
! Fixez le câblage avec des serre-fils ou de la
bande adhésive. Pour protéger le câblage, en-
roulez les sections en contact avec des pièces
en métal dans du ruban adhésif.
Fr
18
Section
03
Connexion des appareils
! Ne découpez jamais lisolation de lalimenta-
tion pour alimenter dautres équipements. La
capacité en courant du fil est limitée.
PRÉCAUTION
! Ne raccourcissez jamais aucun fil, faute de
quoi le circuit de protection risque de fonc-
tionner de manière incorrecte.
! Ne câblez jamais le câble négatif du haut-par-
leur directement à la masse.
! Ne réunissez jamais ensemble les câbles né-
gatifs de plusieurs haut-parleurs.
! Si le fil de la télécommande du système de
lamplificateur est connecté à la borne dali-
mentation via le contact dallumage (12 V CC),
lamplificateur reste sous tension que le sys-
tème stéréo du véhicule soit allumé ou non,
ce qui peut épuiser la batterie lorsque le mo-
teur est à larrêt ou au ralenti.
! Installez et positionnez le fil de batterie vendu
séparément aussi loin que possible des fils de
haut-parleurs.
Installez et positionnez le fil de batterie vendu
séparément, le fil de terre, les fils de haut-par-
leurs et lamplificateur aussi loin que possible
de lantenne, du câble dantenne et du
syntoniseur.
Connexion des haut-parleurs
Cet amplificateur peut être connecté à deux
haut-parleurs en parallèle. Connectez les fils
des haut-parleurs en fonction du mode selon
lillustration ci-dessous.
Précautions à prendre pour une
connexion parallèle
! Lorsque vous branchez deux haut-parleurs
en parallèle, assurez-vous que limpédance
synthétique est comprise entre 1 W à8W
pour éviter que lamplificateur ne prenne
feu, ne dégage de la fumée et/ou ne soit
endommagé.
! Lorsquil est connecté en parallèle avec
une impédance synthétique inférieure à
1 W, à savoir en condition de fonctionne-
ment normal, le son de cet amplificateur
peut automatiquement être coupé en cas
démission dun son à volume élevé. Bais-
sez le volume jusquà ce que la fonction de
coupure du son soit annulée.
Lors de la connexion à un haut-parleur
Sortie des haut-parleurs
Lors de la connexion à deux haut-
parleurs
La sortie des deux haut-parleurs est identique
à celle dun haut-parleur.
Sortie des haut-parleurs
Fr
19
Section
Français
03
Connexion des appareils
Connexions lors de
lutilisation du fil dentrée
des haut-parleurs
Connectez les fils de sortie des haut-parleurs
du système stéréo du véhicule à lamplifica-
teur à laide du fil dentrée des haut-parleurs
fourni, avec cordon RCA.
1 Système stéréo du véhicule
2 Sortie des haut-parleurs
3 Rouge : + droit
4 Noir : * droit
5 Noir : * gauche
6 Blanc : + gauche
7 Fil dentrée des haut-parleurs avec cordon
RCA
Vers le jack dentrée RCA de cet appareil
Remarques
! Si les fils des haut-parleurs avec cordon RCA
dun appareil central sont connectés à cet am-
plificateur, lamplificateur se met automati-
quement en service lorsque lappareil central
est mis en service. Lorsque lappareil central
est mis hors service, lamplificateur se met au-
tomatiquement hors service. Cette fonction
peut ne pas fonctionner sur certains appareils
centraux. Dans ce cas, utilisez le fil dune télé-
commande du système (vendu séparément).
Si plusieurs amplificateurs sont connectés de
manière synchrone, reliez lappareil central et
tous les amplificateurs via le fil de la télécom-
mande du système.
! Connectez le fil de la télécommande du sys-
tème lorsque vous souhaitez mettre le sys-
tème stéréo du véhicule sous tension, et non
lamplificateur.
! Cet amplificateur sélectionne automatique-
ment un mode de signal dentrée entre le ni-
veau RCA et le niveau de haut-parleur en
détectant un signal dentrée.
Connexions de bornes sans
soudure
! Etant donné que le fil se relâche dans le
temps, il doit être inspecté régulièrement et
resserré si nécessaire.
! Ne soudez et ne pliez pas les extrémités
des fils tordus.
! Lors du serrage, veillez à ne pas coincer la
gaine isolante du fil.
! Utilisez la clé hexagonale fournie pour ser-
rer et desserrer la vis de la borne de lampli-
ficateur et pour serrer fermement le fil.
Veillez à ne pas trop serrer la vis, faute de
quoi le fil pourrait être endommagé.
Connexion de la borne
dalimentation
ATTENTION
Si le fil de la batterie nest pas fermement fixé à la
borne à laide des vis de la borne, des risques de
surchauffe, danomalie de fonctionnement et de
blessures, brûlures mineures incluses, existent.
! Utilisez toujours le fil de la batterie et le fil
de terre recommandés, qui sont vendus sé-
parément. Connectez le fil de la batterie di-
rectement sur la borne positive (+)dela
batterie du véhicule et le fil de terre sur la
carrosserie du véhicule.
! La taille de fils recommandée (AWG : Ame-
rican Wire Gauge) est la suivante. Le fil de
la batterie, le fil de terre et le fil de terre di-
recte en option doivent être de la même
taille.
! Utilisez un fil de 8 AWG à 16 AWG pour les
haut-parleurs.
Fr
20
Section
03
Connexion des appareils
1 / 1

Pioneer GM-D8601 Руководство пользователя

Категория
Усилители звука для автомобилей
Тип
Руководство пользователя
Это руководство также подходит для

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ

Спросите документ