DeWalt DWE4157F Инструкция по эксплуатации

final page size: 8.5x 5.5in

DWE4157F

https://tm.by

Интернет-магазин TM.by

ENGLISH

English (original instructions) 3

Pусский (перевод соригинала инструкции) 15

Українська (переклад з оригінальної інструкції) 31

DeWALT

https://tm.by

Интернет-магазин TM.by

Fig. A

Fig. B

3 2

4 8

90˚ 90˚

Fig. C

XXXX XX XX

https://tm.by

Интернет-магазин TM.by

Fig. F Fig. G

Fig. D Fig. E

https://tm.by

Интернет-магазин TM.by

ENGLISH

WARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

Denotes risk of electricshock.

Denotes risk offire.

The vibration and/or noise emission level given in this

information sheet has been measured in accordance with

a standardised test given in EN60745and may be used to

compare one tool with another. It may be used for a preliminary

assessment ofexposure.

WARNING: The declared vibration and/or noise emission

level represents the main applications of the tool. However

if the tool is used for different applications, with different

accessories or poorly maintained, the vibration and/or

noise emission may differ. This may significantly increase

the exposure level over the total workingperiod.

An estimation of the level of exposure to vibration and/or

noise should also take into account the times when the tool

is switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total workingperiod.

Identify additional safety measures to protect the operator

from the effects of vibration and/or noise such as: maintain

the tool and the accessories, keep the hands warm

(relevant for vibration), organisation of workpatterns.

DWE4157F

Voltage VAC 230

Type 1

Power input W900

Rated speed min‑1 11800

Wheel diameter mm 125

Spindle diameter M14

Spindle length mm 14

Weight kg

2.0

Noise values and vibration values (triax vector sum) according to EN60745‑2‑3:

LPA (emission sound pressure level) dB(A) 87

LWA (sound power level) dB(A) 98

K (uncertainty for the given sound level) dB(A) 3

Surface grinding

Vibration emission value a

h,AG

=m/s26.8

Uncertainty K = m/s21.5

Disc sanding

Vibration emission value a

h,DS

=m/s24.1

Uncertainty K = m/s21.5

EC-Declaration of Conformity

Machinery Directive

Small Angle Grinder

DWE4157F

DeWALT

declares that these products described under

Technical Data are in compliance with:

2006/42/EC, EN60745‑1:2009+A1:2010, EN60745‑2‑3:2011+A2:

2013+A11:2014+A12:2014+A13:2015.

These products also comply with Directive 2014/30/EU and

2011/65/EU. For more information, please contact

DeWALT

the following address or refer to the back of themanual.

The undersigned is responsible for compilation of the technical

file and makes this declaration on behalf of

DeWALT

Markus Rompel

Vice‑President Engineering, PTE‑Europe

DeWALT

, Richard‑Klinger‑Straße 11,

D‑65510, Idstein, Germany

11.01.2018

English (original instructions)

Congratulations!

You have chosen a

DeWALT

tool. Years of experience, thorough

product development and innovation make

DeWALT

one of the

most reliable partners for professional power toolusers.

Technical Data

SMALL ANGLE GRINDER

DWE4157F

https://tm.by

Интернет-магазин TM.by

ENGLISH

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTUREREFERENCE

The term “power tool” in the warnings refers to your

mains‑operated (corded) power tool or battery‑operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,

non‑skid safety shoes, hard hat or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off‑position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be

caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust‑relatedhazards.

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe

injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the

power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

https://tm.by

Интернет-магазин TM.by

ENGLISH

ADDITIONAL SPECIFIC SAFETY RULES

Safety Warnings Common for Grinding,

Sanding, Wire Brushing or Abrasive

Cutting-Off Operations

a ) This power tool is intended to function as a

grinder, sander, wire brush, cut‑off tool. Read all

safety warnings, instructions, illustrations and

specifications provided with this power tool. Failure

to follow all instructions listed below may result in electric

shock, fire and/or seriousinjury.

b ) Operations such as polishing are not recommended

to be performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personalinjury.

c ) Do not use accessories which are not specifically

designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safeoperation.

d ) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed can

break and flyapart.

e ) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can not be

adequately guarded orcontrolled.

f ) Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by

flanges, the arbour hole of the accessory must fit the

locating diameter of the flange. Accessories that do

not match the mounting hardware of the power tool will

run out of balance, vibrate excessively and may cause loss

ofcontrol.

g ) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheel for

chips and cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or cracked wires.

If power tool or accessory is dropped, inspect for

damage or install an undamaged accessory. After

inspecting and installing an accessory, position

yourself and bystanders away from the plane of

the rotating accessory and run the power tool at

maximum no‑load speed for one minute. Damaged

accessories will normally break apart during this testtime.

h ) Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpectedsituations.

5) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

h ) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping flying

debris generated by various operations. The dust mask or

respirator must be capable of filtrating particles generated

by your operation. Prolonged exposure to high intensity

noise may cause hearingloss.

i ) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may fly away and

cause injury beyond immediate area ofoperation.

j ) Hold the power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live" and

could give the operator an electricalshock.

k ) Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinningaccessory.

l ) Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory

may grab the surface and pull the power tool out of

yourcontrol.

m ) Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

yourbody.

n ) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electricalhazards.

o ) Do not operate the power tool near flammable

materials. Sparks could ignite thesematerials.

p ) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution orshock.

FURTHER SAFETY INSTRUCTIONS FOR ALL

OPERATIONS

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or

snagging causes rapid stalling of the rotating accessory which

in turn causes the uncontrolled power tool to be forced in the

direction opposite of the accessory’s rotation at the point of

thebinding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or

https://tm.by

Интернет-магазин TM.by

ENGLISH

away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels may also

break under theseconditions.

Kickback is the result of tool misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

a ) Maintain a firm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start up. The operator can control torque reaction

or kickback forces, if proper precautions aretaken.

b ) Never place your hand near the rotating accessory.

Accessory may kickback over yourhand.

c ) Do not position your body in the area where power

tool will move if kickback occurs. Kickback will propel

the tool in direction opposite to the wheel’s movement at

the point ofsnagging.

d ) Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency to

snag the rotating accessory and cause loss of control

orkickback.

e ) Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent kickback

and loss ofcontrol.

Safety Warnings Specific for Grinding and

Cutting-Off Operations

a ) Use only wheel types that are recommended for your

power tool and the specific guard designed for the

selected wheel. Wheels for which the power tool was not

designed cannot be adequately guarded and areunsafe.

b ) The grinding surface of centre depressed wheels

must be mounted below the plane of the guard lip.

An improperly mounted wheel that projects through the

plane of the guard lip cannot be adequatelyprotected.

c ) The guard must be securely attached to the power

tool and positioned for maximum safety, so the least

amount of wheel is exposed towards the operator.

The guard helps to protect the operator from broken wheel

fragments, accidental contact with wheel and sparks that

could igniteclothing.

d ) Wheels must be used only for recommended

applications. For example: do not grind with the side

of cut‑off wheel. Abrasive cut‑off wheels are intended

for peripheral grinding, side forces applied to these wheels

may cause them toshatter.

e ) Always use undamaged wheel flanges that are

of correct size and shape for your selected wheel.

Proper wheel flanges support the wheel thus

reducing the possibility of wheel breakage. Flanges

for cut‑off wheels may be different from grinding

wheelflanges.

f ) Do not use worn down wheels from larger power

tools. Wheel intended for larger power tool is not suitable

for the higher speed of a smaller tool and mayburst.

Additional Safety Warnings Specific for

Cutting-Off Operations

a ) Do not "jam" the cut‑off wheel or apply excessive

pressure. Do not attempt to make an excessive depth

of cut. Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheelbreakage.

b ) Do not position your body in line with and behind

the rotating wheel. When the wheel, at the point of

operations, is moving away from your body, the possible

kickback may propel the spinning wheel and the power

tool directly atyou.

c ) When wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold

the power tool motionless until the wheel comes to a

complete stop. Never attempt to remove the cut‑off

wheel from the cut while the wheel is in motion

otherwise kickback may occur. Investigate and take

corrective action to eliminate the cause of wheelbinding.

d ) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re‑enter the cut. The wheel may bind, walk up

or kickback if the power tool is restarted in theworkpiece.

e ) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own

weight. Supports must be placed under the workpiece

near the line of cut and near the edge of the workpiece on

both sides of thewheel.

f ) Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can causekickback.

Additional Safety Instructions for Sanding

Operations

a ) Do not use excessively oversized sanding disc

paper. Follow manufacturer’s recommendations,

when selecting sanding paper. Larger sanding paper

extending beyond the sanding pad presents a laceration

hazard and may cause snagging, tearing of the disc

orkickback.

Additional Safety Instructions for Wire

Brushing Operations

a ) Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress

the wires by applying excessive load to the brush.

The wire bristles can easily penetrate llight clothing and/

orskin.

https://tm.by

Интернет-магазин TM.by

ENGLISH

Description (Fig. A)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

1 Slider switch

2 Side handle adaptor

3 Side handle

4 Spindle

5 Spindle lock button

6 Unthreaded backing flange

7 Threaded locking flange

8 Guard

9 Guard release lever

Intended Use

Your heavy‑duty small angle grinder has been designed

for professional grinding, sanding, wire brushing and

cuttingapplications.

Do not use under wet conditions or in the presence of

flammable liquids orgases.

Your heavy‑duty angle grinder is a professional powertool.Do

not let children come into contact with the tool. Supervision is

required when inexperienced operators use thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

Date Code Position (Fig. A)

The date code 10, which also includes the year of manufacture,

is printed into thehousing.

Example:

2019 XX XX

Year of Manufacture

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual beforeuse.

Wear earprotection.

Wear eyeprotection.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the power supply corresponds to the voltage

on the ratingplate.

Your

DeWALT

tool is double insulated in accordance

with EN60745; therefore no earth wire isrequired.

If the supply cord is damaged, it must be replaced only by

DeWALT

or an authorised serviceorganisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

• Connect the blue lead to the neutralterminal.

WARNING: No connection is to be made to the

earthterminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 13A.

Using an Extension Cable

If an extension cable is required, use an approved 3–core

extension cable suitable for the power input of this tool (see

Technical Data).The minimum conductor size is 1.5mm2; the

maximum length is 30m.

When using a cable reel, always unwind the cablecompletely.

Residual Risks

WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

SAVE THESE INSTRUCTIONS

b ) If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel

or brush may expand in diameter due to work and

centrifugalforces.

Additional Safety Rules for Grinders

a ) Do not use Type 11(flaring cup) wheels on this tool.

Using inappropriate accessories can result ininjury.

b ) Always use side handle. Tighten the handle securely.

The side handle should always be used to maintain control

of the tool at alltimes.

Package Contents

The package contains:

1 Angle grinder

1 Guard

1 Side handle

1 Side handle adaptor

1 Unthreaded backing flange

1 Threaded locking flange

1 Instruction manual

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

https://tm.by

Интернет-магазин TM.by

ENGLISH

Attaching Side Handle (Fig.A)

WARNING: Before using the tool, check that the handle is

tightenedsecurely.

Screw the side handle adapter2 into one of the holes on

either side of the gear case, then screw the side handle3 into

the adapter. The adapter MUST be used together with the

side handle. If the adapter is missing, stop using the tool, find

a nearest

DeWALT

service center for a new adaptor. The side

handle should always be used to maintain control of the tool at

alltimes.

Rotating the Gear Case (Fig. B)

To improve user comfort, the gear case will rotate 90° for

cuttingoperations.

1. Remove the four corner screws attaching the gear case to

motorhousing.

2. Without separating the gear case from motor housing,

rotate the gear case head to desiredposition.

NOTE: If the gear case and motor housing become separated by

more than 3.0mm, the tool must be serviced and re‑assembled

by a

DeWALT

service center. Failure to have the tool serviced

may cause motor and bearingfailure.

3. Reinstall screws to attach the gear case to the motor

housing. Tighten screws to 2Nm torque. Overtightening

could cause screws tostrip.

Guards

CAUTION: Guards must be used with all grinding

wheels, cutting wheels and sanding flap discs. The

tool may be used without a guard only when sanding

with conventional sanding discs. Some applications may

require purchasing the correct guard from your local

dealer or authorized servicecenter.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

WARNING: Use only

DeWALT

battery packs andchargers.

Features

No‑Volt

The No‑volt function stops the grinder restarting without the

switch being cycled if there is a break in the powersupply.

Electronic Soft Start

This feature limits the initial start up momentum, allowing the

speed to build up gradually over a 1secondperiod.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

NOTE: Edge grinding and cutting can be performed with Type

27wheels designed and specified for this purpose; 6.35mm

thick wheels are designed for surface grinding while thinner

Type 27wheels need to be examined for the manufacturer's

label to see if they can be used for surface grinding or only

edge grinding/cutting. A Type 1guard must be used for any

wheel where surface grinding is forbidden. Cutting can also be

performed by using a Type41wheel and a Type 1guard.

NOTE: See the Grinding and Cutting AccessoryChart to select

the proper guard/accessorycombination.

Adjusting and Mounting Guard(Fig.C)

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start‑up

can causeinjury.

Adjustment Options (Fig. C)

For guard adjustment, the guard release lever9 engages

one of the alignment holes13 on the guard collar using a

ratchetingfeature.

Mounting Guard (Fig. C)

CAUTION: Prior to mounting guard, ensure the screw,

lever, and spring are fitted correctly before mounting

theguard.

1. With the spindle facing the operator, align the guard parallel

to the mounting slot14 ingearcase.

2. Slide the guard into the mounting slot with the guard

tabs12 riding along the 2flat sides of the collar just above

the mountingslot.

3. Press and hold the guard release lever9 and rotate

the guard around until the lever engages one of the

alignmentholes13.

4. Release the guard releaselever.

5. To position the guard:

Press and hold the guard release lever9. Rotate the

guard clockwise or anti‑clockwise into the desired

workingposition.

NOTE: The guard body should be positioned between

the spindle and the operator to provide maximum

operatorprotection.

The guard release lever should snap into one of the

alignment holes13 on the guard collar. This ensures that

the guard issecure.

6. To remove the guard, press and hold the guard release lever

and rotate the guard around until the lever disengages

from the alignmentholes, then slide the guard off the

mountingslot.

Flanges and Wheels

WARNING: Hubbed wheels are not to be used on this

grinder since the grinding surface of the wheel might

not be within the guard lip. An improperly mounted

hubbed wheel that projects through the plane of the

guard lip cannot be adequatelyprotected.

https://tm.by

Интернет-магазин TM.by

ENGLISH

Proper hand position requires one hand on the side handle3,

with the other hand on the body of the tool, as shown in

FigureF.

Slider Switch (Fig.A)

CAUTION: Hold the side handle and body of the tool

firmly to maintain control of the tool at start up and

during use and until the wheel or accessory stops rotating.

Make sure the wheel has come to a complete stop be fore

laying the tooldown.

NOTE: To reduce unexpected tool movement, do not switch

the tool on or off while under load conditions. Allow the grinder

Proper Hand Position (Fig. F)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and

applicableregulations.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

Mounting Non‑Hubbed Wheels (Fig. A, D)

WARNING: Failure to properly seat the flange/ clamp nut/

wheel could result in serious injury (or damage to the tool

orwheel).

CAUTION: Included flanges must be used with Type

27grinding wheels and Type41and Type 42cutting

wheels. See the Grinding and Cutting AccessoryChart

for moreinformation.

WARNING: A closed, two‑sided cutting wheel guard is

re quired when using cutting wheels.

WARNING: Use of a damaged flange or guard or fail ure

to use proper flange and guard can re sult in injury due

to wheel breakage and wheel contact. See the Grinding

and Cutting AccessoryChart for moreinformation.

1. Place the tool on a table, guardup.

2. Install the unthreaded backing flange6 on spindle4 with

the raised centre (pilot) facing the wheel.

3. Place wheel15 against the backing flange, centreing the

wheel on the raised centre (pilot) of the backingflange.

4. While depressing the spindle lock button 5 and with the

hex depressions facing away from the wheel, thread the

threaded locking flange7 on spindle so that the lugs

engage the two slots in thespindle.

5. While depressing the spindle lock button, tighten the

threaded locking flange7 using the hexwrench 11.

6. To remove the wheel, depress the spindle lock button and

loosen the threaded lockingflange.

Mounting Sanding Backing Pads (Fig.A, E)

NOTE: Use of a guard with sanding discs that use backing pads,

often called fiber resin discs, is not required. Since a guard is

not required for these accessories, the guard may or may not fit

correctly ifused.

WARNING: Failure to properly seat the flange/ clamp nut/

wheel could result in serious injury (or damage to the tool

orwheel).

WARNING: Proper guard must be reinstalled for grinding

wheel, cutting wheel, sanding flap disc, wire brush or

wire wheel applications after sanding applications

arecomplete.

1. Place or appropriately thread backing pad16 on

thespindle 4.

2. Place the sanding disc17 on the backing pad16.

3. While depressing spindle lock button5, thread clamp

nut18 on spindle, piloting the raised hub on the clamp nut

into the centre of san ding disc and backingpad.

4. Tighten the clamp nut by hand. Then depress the spindle

lock button while turning the sanding disc until the sanding

disc and clamp nut aresnug.

5. To remove the wheel, grasp and turn the backing pad and

sanding pad while depressing the spindle lockbutton.

Mounting Wire Cup Brushes and WireWheels

(Fig.A)

WARNING: Failure to properly seat the flange/ clamp nut/

wheel could result in serious injury (or damage to the tool

orwheel).

CAUTION: To reduce the risk of personal injury,

wear work gloves when handling wire brushes and

wheels. They can becomesharp.

CAUTION: To reduce the risk of damage to the tool,

wheel or brush must not touch guard when mounted

or while in use. Undetectable damage could occur to

the accessory, causing wires to fragment from accessory

wheel orcup.

Wire cup brushes or wire wheels install directly on the threaded

spindle without the use of flanges. Use only wire brushes or

wheels provided with a M14threaded hub. These accessories

are available at extra cost from your local dealer or authorised

servicecentre.

1. Place the tool on a table, guardup.

2. Thread the wheel on the spindle byhand.

3. Depress spindle lock button5 and use a wrench on the

hub of the wire wheel or brush to tighten thewheel.

4. To remove the wheel, reverse the aboveprocedure.

NOTICE: To reduce the risk of damage to the tool, properly

seat the wheel hub before turning the toolon.

https://tm.by

Интернет-магазин TM.by

ENGLISH

to run up to full speed before touching the work surface. Lift the

tool from the surface before turning the tool off. Allow the tool

to stop rotating before putting itdown.

WARNING: Before connecting the tool to a power supply,

be sure the slider switch is in the off position by pressing

the rear part of the switch and releasing. Ensure the slider

switch is in the off position as described above after any

interruption in power supply to the tool, such as the

activation of a ground fault interrupter, throwing of a

circuit breaker, accidental unplugging, or power failure. If

the slider switch is locked on when the power is connected,

the tool will startunexpectedly.

To start the tool, slide the ON/OFF slider switch1 toward

the front of the tool. To stop the tool, release the ON/OFF

sliderswitch.

For continuous operation, slide the switch toward the front of

the tool and press the forward part of the switch inward. To stop

the tool while operating in continuous mode, press the rear part

of the slider switch andrelease.

Spindle Lock (Fig.G)

The spindle lock button5 is provided to prevent the spindle

from rotating when installing or removing wheels. Operate the

spindle lock only when the tool is turned off, unplugged from

the power supply, and has come to a completestop.

NOTICE: To reduce the risk of damage to the tool, do

not engage the spindle lock while the tool is operating.

Damage to the tool will result and attached accessory

may spin off possibly resulting ininjury.

To engage the lock, depress the spindle lock button and rotate

the spindle until you are unable to rotate the spindlefurther.

Surface Grinding, Sanding and Wire

Brushing

CAUTION: Always use the correct guard per the

instructions in thismanual.

WARNING: Metal dust build‑up. Extensive use of flap

discs in metal applications can result in the increased

potential for electric shock. To reduce this risk, insert an

RCD before use and clean the ventilation slots daily by

blowing dry compressed air into the ventilation slots

inaccordance with the below maintenanceinstructions.

To perform work on a the surface of a workpiece:

1. Allow the tool to reach full speed before touching the tool

to the worksurface.

2. Apply minimum pressure to the work surface, allowing

the tool to operate at high speed. Material removal rate is

greatest when the tool operates at highspeed.

Angle

3. Maintain an appropriate angle between the tool and work

surface. Refer to the chart according to particularfunction.

Function Angle

Grinding 20˚‑30˚

Sanding with Flap Disc 5˚‑10˚

Sanding with Backing Pad 5˚‑15˚

Wire Brushing 5˚‑10˚

4. Maintain contact between the edge of the wheel and the

worksurface.

‑If grinding, sanding with flap discs or wire brushing

move the tool continuously in a forward and back

motion to avoid creating gouges in the worksurface.

‑If sanding with a backing pad, move the tool constantly

in a straight line to prevent burning and swirling of

worksurface.

NOTE: Allowing the tool to rest on the work surface without

moving will damage theworkpiece.

5. Remove the tool from work surface before turning tool off.

Allow the tool to stop rotating before laying itdown.

CAUTION: Use extra care when working over an edge, as

a sudden sharp movement of grinder may beexperienced.

Precautions To Take When Working on a Painted

Workpiece

1. Sanding or wire brushing of lead based paint is NOT

RECOMMENDED due to the difficulty of controlling the

contaminated dust. The greatest danger of lead poisoning is

to children and pregnantwomen.

2. Since it is difficult to identify whether or not a paint contains

lead without a chemical analysis, we recommend the

following precautions when sanding any paint:

Personal Safety

1. No children or pregnant women should enter the work area

where the paint sanding or wire brushing is being done

until all clean up iscompleted.

2. A dust mask or respirator should be worn by all persons

entering the work area. The filter should be replaced daily or

whenever the wearer has difficultybreathing.

NOTE: Only those dust masks suitable for working with lead

paint dust and fumes should be used. Ordinary painting

masks do not offer this protection. See your local hardware

dealer for the proper N.I.O.S.H. approvedmask.

3. NO EATING, DRINKING or SMOKING should be done in the

work area to prevent ingesting contaminated paint particles.

Workers should wash and clean up BEFORE eating, drinking

or smoking. Articles of food, drink, or smoking should not be

left in the work area where dust would settle onthem.

Environmental Safety

1. Paint should be removed in such a manner as to minimize

the amount of dustgenerated.

2. Areas where paint removal is occurring should be sealed

with plastic sheeting of 4milsthickness.

3. Sanding should be done in a manner to reduce tracking of

paint dust outside the workarea.

https://tm.by

Интернет-магазин TM.by

ENGLISH

Lubrication

Your power tool requires no additionallubrication.

MAINTENANCE

Your power tool has been designed to operate over a long

period of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regularcleaning.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.

Cleaning and Disposal

1. All surfaces in the work area should be vacuumed and

thoroughly cleaned daily for the duration of the sanding

project. Vacuum filter bags should be changedfrequently.

2. Plastic drop cloths should be gathered up and disposed

of along with any dust chips or other removal debris. They

should be placed in sealed refuse receptacles and disposed

of through regular trash pick‑upprocedures.

During clean up, children and pregnant women should be

kept away from the immediate workarea.

3. All toys, washable furniture and utensils used by children

should be washed thoroughly before being usedagain.

Edge Grinding and Cutting

WARNING: Do not use edge grinding/cutting wheels for

surface grinding applications because these wheels are

not designed for side pressures encountered with surface

grinding. Wheel breakage and injury mayresult.

CAUTION: Wheels used for edge grinding and cutting

may break or kick back if they bend or twist while the tool

is being used. In all edge grinding/cutting operations, the

open side of the guard must be positioned away from

theoperator.

NOTICE: Edge grinding/cutting with a Type27wheel

must be limited to shallow cutting and notching—less

than 13mm in depth when the wheel is new. Reduce the

depth of cutting/notching equal to the reduction of the

wheel radius as it wears down. Refer to the Grinding and

Cutting AccessoryChart for more information. Edge

grinding/cutting with a Type 41wheel requires usage of a

Type 1guard.

1. Allow the tool to reach full speed before touching the tool

to the worksurface.

2. Apply minimum pressure to the work surface, allowing

the tool to operate at high speed. Grinding/cutting rate is

greatest when the tool operates at highspeed.

3. Position yourself so that the open‑underside of the wheel is

facing away fromyou.

4. Once a cut is begun and a notch is established in the

workpiece, do not change the angle of the cut. Changing

the angle will cause the wheel to bend and may cause

wheel breakage. Edge grinding wheels are not designed to

withstand side pressures caused bybending.

5. Remove the tool from the work surface before turning

the tool off. Allow the tool to stop rotating before laying

itdown.

Metal Applications

When using the tool in metal applications, make sure that a

residual current device (RCD) has been inserted to avoid residual

risks caused by metalswarf.

If the power supply is shut off by the RCD, take the tool to an

authorised D

WALT repairagent.

WARNING: In extreme working conditions, conductive

dust can accumulate inside the machine housing when

working with metal. This can result in the protective

insulation in the machine becoming degraded with a

potential risk of an electricalshock.

To avoid build‑up of metal swarf inside the machine, we

recommend to clear the ventilation slots on a daily basis. Refer

toMaintenance.

Cutting Metal

For cutting with bonded abrasives, always use the

guardtype1.

When cutting, work with moderate feed, adapted to the

material being cut. Do not exert pressure onto the cutting disc,

tilt or oscillate themachine.

Do not reduce the speed of running down cutting discs by

applying sidewardpressure.

The machine must always work in an upgrinding motion.

Otherwise, the danger exists of it being pushed uncontrolled

out of thecut.

When cutting profiles and square bar, it is best to start at the

smallest crosssection.

Rough Grinding

Never use a cutting disc forroughing.

Always use the guard type27.

The best roughing results are achieved when setting the

machine at an angle of 30° to 40°. Move the machine back and

forth with moderate pressure. In this manner, the workpiece

will not become too hot, does not discolour and no grooves

areformed.

Cutting Stone

The machine shall be used only for drycutting.

For cutting stone, it is best to use a diamond cutting disc.

Operate the machine only with additional dust protectionmask.

Working Advice

Exercise caution when cutting slots in structuralwalls.

Slots in structural walls are subject to the country‑specific

regulations. These regulations are to be observed under all

circumstances.Before beginning work, consult the responsible

structural engineer, architect or the constructionsupervisor.

https://tm.by

Интернет-магазин TM.by

ENGLISH

Protecting the Environment

Separate collection. Products marked with this symbol

must not be disposed of with normal householdwaste.

Products contain materials that can be recovered

or recycled reducing the demand for raw materials.

Please recycle electrical products according to local provisions.

Further information is available at www.2helpU.com.

Max.

[mm] [mm] Min.

Rotation

[min.–1]

Periphical

speed

[m/s]

Threaded

hole length

[mm]

D b d

125 622.23 10500 80 –

125 – – 10500 80 –

b75 30 M14 10500 45 20.0

125 12 M14 10500 80 20.0

Optional Accessories

WARNING: Since accessories, other than those offered

DeWALT

, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only

DeWALT

recommended

accessories should be used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Cleaning

WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals

for cleaning the non‑metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

https://tm.by

Интернет-магазин TM.by

ENGLISH

Grinding and Cutting Accessory Chart

Guard Type Accessory Description How to Fit Grinder

Type 27

Guard

Depressed centre

grinding disc Type 27guard

Backing flange

Type 27depressed

centre wheel

Threaded locking flange

Flap wheel

Wire wheels

Wire wheels with

threaded nut

Type 27guard

Wire wheel

Wire cup with

threaded nut

Type 27guard

Wire brush

Backing pad/

sanding sheet

Type 27guard

Rubber backing pad

Sanding disc

Threaded clamp nut

https://tm.by

Интернет-магазин TM.by

ENGLISH

Grinding and Cutting Accessory Chart

Guard Type Accessory Description How to Fit Grinder

Type 1

Guard

Masonry cutting

disc, bonded

Type 1guard

Backing flange

Cutting wheel

Threaded locking flange

Metal

cutting disc,

bonded

Type 1

Guard

Type 27

Guard

Diamond cutting

wheels

https://tm.by

Интернет-магазин TM.by

PУССКИЙ

ВНИМАНИЕ: Во избежание риска получения травм

ознакомьтесь синструкцией.

:  



Ниже описывается уровень опасности, обозначаемый

каждым из предупреждений. Прочитайте руководство

иобратите внимание на данныесимволы.

ОПАСНО: Обозначает опасную ситуацию, которая

неизбежно приведет ксерьезной травме или

    

Директива по механическому оборудованию

Малая угловая шлифовальная машина

DWE4157F

DeWALT

заявляет, что продукция, описанная в разделе

«Технические характеристики», соответствует:

2006/42/EC, EN60745‑1:2009+A1:2010, EN60745‑2‑3:2011+A2:

2013+A11:2014+A12:2014+A13:2015.

Эти продукты также соответствуют Директивам 2014/30/EU и

2011/65/EU. За дополнительной информацией обращайтесь

в компанию

DeWALT

по адресу, указанному ниже или

приведенному на задней стороне обложкируководства.

Нижеподписавшийся несет ответственность за составление

технической документации и составил данную декларацию

по поручению компании

DeWALT

Маркус Ромпель

Вице‑президент отдела по разработке и производству,

PTE‑Europe

DeWALT

, Richard‑Klinger‑Straße 11,

D‑65510, Idstein, Germany

11.01.2018

необходимо учитывать время, когда инструмент

выключен или то время, когда он работает

на холостом ходу. Это может привести к

значительному снижению уровня воздействия

вибрации в течение всего рабочегопериода.

Определите дополнительные меры техники

безопасности для защиты оператора от

воздействия шума и/или вибрации, а именно:

поддержание инструмента и дополнительных

принадлежностей в рабочем состоянии, создание

комфортных условий работы (соответствующих

вибрации), хорошая организация рабочегоместа.

Значение шумовой эмиссии и/или эмиссии вибрации,

указанное в данном справочном листке, было получено

в соответствии со стандартным тестом, приведенным

в EN60745, и может использоваться для сравнения

инструментов. Кроме того, оно может использоваться для

предварительной оценки воздействиявибрации.

ОСТОРОЖНО! Заявленное значение шумовой

эмиссии и/или эмиссии вибрации относится к

основным областям применения инструмента.

Однако, если инструмент используется для

различных целей, с различными дополнительными

принадлежностями или при ненадлежащем уходе, то

уровень шума и/или вибрации может измениться.

Это может привести к значительному увеличению

уровня воздействия вибрации в течение всего

рабочегопериода.

При расчете приблизительного значения уровня

воздействия шума и/или вибрации также

DWE4157F

Напряжение Вперем. тока 230

Тип 1

Потребляемая мощность Вт 900

Номинальное количество оборотов мин.‑1 11800

Диаметр круга мм 125

Диаметр шпинделя M14

Длина шпинделя мм 14

Вес кг

2,0

Значения шума и вибрации (сумма векторов в трех плоскостях) в

соответствии с EN60745‑2‑3:

LPA (уровень звукового давления) дБ(A) 87

LWA (уровень акустической мощности) дБ(A) 98

K (погрешность для заданного уровня

мощности)

дБ(A) 3

Шлифование поверхности

Значение эмиссии вибрации a

h,AG

=м/с26,8

Погрешность K = м/с21,5

Шлифование диском

Значение эмиссии вибрации a

h,DS

=м/с24,1

Погрешность K = м/с21,5

!

Вы приобрели инструмент

DeWALT

. Многолетний опыт,

тщательная разработка изделий иинновации делают

компанию

DeWALT

одним из самых надёжных партнеров для

пользователей профессиональногоэлектроинструмента.

 

Pусский (перевод соригинала инструкции)

МАЛАЯ УГЛОВАЯ ШЛИФОВАЛЬНАЯ МАШИНА

DWE4157F

https://tm.by

Интернет-магазин TM.by

PУССКИЙ

2) Электробезопасность

a ) Штепсельная вилка электроинструмента

должна соответствовать розетке. Никогда

не меняйте вилку инструмента. Запрещается

использовать переходники квилкам для

электроинструментов сзаземлением.

Использование оригинальных штепсельных вилок,

соответствующих типу сетевой розетки снижает

риск поражения электрическимтоком.

b ) Избегайте контакта сзаземленными

поверхностями, такими как трубы,

радиаторы ихолодильники. Если вы будете

заземлены, увеличивается риск поражения

электрическимтоком.

c ) Запрещается оставлять электроинструмент

под дождем ивместах повышенной влажности.

При попадании воды вэлектроинструмент риск

поражения электротокомвозрастает.

d ) Берегите кабель от повреждений. Никогда

не используйте кабель для переноски

инструмента, не тяните за него, пытаясь

отключить инструмент от сети. Держите

кабель подальше от источников тепла, масла,

острых углов или движущихся предметов.

Поврежденный или запутанный кабель питания

повышает риск поражения электрическимтоком.

e ) При работе сэлектроинструментом на

открытом воздухе используйте удлинитель,

подходящий для использования на улице.

Использования кабеля питания, предназначенного

для использования вне помещения, снижает риск

поражения электрическимтоком.

f ) Если использование электроинструмента

вусловиях повышенной влажности неизбежно,

используйте устройства защитного

отключения (УЗО) для защиты сети.

Использование УЗО сокращает риск поражения

электрическимтоком.

3) Обеспечение индивидуальной

безопасности

a ) Будьте внимательны, смотрите, что делаете

ине забывайте оздравом смысле при работе

сэлектроинструментом. Запрещается

работать сэлектроинструментом

всостоянии усталости, наркотического,

алкогольного опьянения или под воздействием

лекарственных препаратов. Невнимательность

при работе сэлектроинструментом может

привести ксерьезным телеснымповреждениям.

b ) Используйте индивидуальные средства

защиты. Всегда используйте защитные очки.

Средства защиты, такие как пылезащитная маска,

обувь снескользящей подошвой, каска изащитные

наушники, используемые при работе, уменьшают

риск получениятравм.

c ) Примите меры для предотвращения

случайного включения. Перед тем как

подключить электроинструмент ксети и/или

  

  



ВНИМАНИЕ: Прочитайте ипросмотрите

все предупреждения, инструкции,

иллюстрации испецификации по данному

электроинструменту. Несоблюдение всех

приведенных ниже инструкций может стать

причиной поражения электрическим током,

возгорания и/или тяжелойтравмы.

СОХРАНИТЕ ВСЕ ИНСТРУКЦИИ ДЛЯ

ПОСЛЕДУЮЩЕГОИСПОЛЬЗОВАНИЯ

Термин «электроинструмент» впредупреждениях

относится кработающим от сети

(проводным) электроинструментам или

работающим от аккумуляторной батареи

(беспроводным)электроинструментам.

1) Безопасность на рабочем месте

a ) Следите за чистотой ихорошим освещением

на рабочем месте. Захламленное или плохо

освещенное рабочее место может стать причиной

несчастногослучая.

b ) Запрещается работать

сэлектроинструментами во

взрывоопасных местах, например, вблизи

легковоспламеняющихся жидкостей, газов

ипыли. Искры, которые появляются при

работе электроинструментов могут привести

квоспламенению пыли илипаров.

c ) Следите за тем, чтобы во время работы

сэлектроинструментом взоне работы

не было посторонних идетей. Отвлекаясь

от работы вы можете потерять контроль

надинструментом.

смертельному исходу, вслучае несоблюдения

соответствующих мербезопасности.

ВНИМАНИЕ: Указывает на потенциально опасную

ситуацию, которая, вслучае несоблюдения

соответствующих мер безопасности,

может привести ксерьезной травме или

смертельномуисходу.

ПРЕДУПРЕЖДЕНИЕ: Указывает на потенциально

опасную ситуацию, которая, вслучае несоблюдения

соответствующих мер безопасности может

стать причиной травм средней или легкой

степенитяжести.

ПОЯСНЕНИЕ: Указывает на практики,

использование которых не связано

сполучением травмы, но если ими пренебречь,

могут привести кпорчеимущества.

Указывает на риск поражения электрическимтоком.

Указывает на рисквозгорания.

https://tm.by

Интернет-магазин TM.by

PУССКИЙ

 

   

   

, , 

   



a ) Этот электроинструмент предназначен

для заточки, шлифования, зачистки

проволочной щеткой и резания. Прочитайте

и просмотрите все предупреждения,

инструкции, иллюстрации и спецификации по

соответствующих навыков работы стакого

рода инструментами. Электроинструмент

представляет опасность вруках

неопытныхпользователей.

e ) Поддерживайте электроинструмент

ипринадлежности висправном состоянии.

Проверьте, не нарушена ли центровка или

не заклинены ли движущиеся детали, нет

ли повреждений или иных неисправностей,

которые могли бы повлиять на работу

электроинструмента. Вслучае обнаружения

повреждений, прежде чем приступить

кэксплуатации электроинструмента, его

нужно отремонтировать. Большинство

несчастных случаев происходит из‑за

электроинструментов, которые не обслуживаются

должнымобразом.

f ) Содержите режущий инструмент востро

заточенном ичистом состоянии. Вероятность

заклинивания инструмента, за которым следят

должным образом икоторый хорошо заточен,

значительно меньше, аработать снимлегче.

g ) Используйте электроинструменты,

принадлежности инасадки всоответствии

сданными инструкциями, принимая во

внимание условия работы ихарактер

выполняемой работы. Использование

электроинструмента для выполнения операций,

для которых он не предназначен, может привести

ксозданию опасныхситуаций.

h ) Все рукоятки иповерхности захватывания

должны быть сухими ибез следов смазки.

Скользкие рукоятки иповерхности захватывания

не позволяют обеспечить безопасность

работы иуправления инструментом

внепредвиденныхситуациях.

5) Обслуживание

a ) Обслуживание электроинструмента

должен проводить квалифицированный

специалист сиспользованием только

оригинальных запасных частей. Это позволит

обеспечить безопасность обслуживаемого

электрифицированногоинструмента.

аккумуляторной батарее, взять инструмент

или перенести его на другое место, убедитесь

втом, что выключатель находится

вположении «Выкл.». Если при переноске

электроинструмента он подключен ксети, ипри

этом ваш палец находится на выключателе, это

может стать причиной несчастныхслучаев.

d ) Уберите все регулировочные или гаечные ключи

перед включением электроинструмента.

Ключ, оставленный на вращающейся части

электроинструмента, может привести ктравме.

e ) Не пытайтесь дотянуться до слишком

удаленных поверхностей. Обувь должна быть

удобной, чтобы вы всегда могли сохранять

равновесие. Это позволит лучше контролировать

электроинструмент внепредвиденныхситуациях.

f ) Одевайтесь соответствующим образом.

Избегайте носить свободную одежду

иювелирные украшения. Следите за тем,

чтобы волосы иодежда не попадали под

движущиеся детали. Возможно наматывание

свободной одежды, ювелирных изделий идлинных

волос на движущиесядетали.

g ) При наличии устройств для подключения

оборудования для удаления исбора пыли

необходимо обеспечить правильность их

подключения иэксплуатации. Использование

устройства для пылеудаления сокращает риски,

связанные спылью.

h ) Не позволяйте хорошему знанию от частого

использования инструментов стать причиной

самонадеянности иигнорирования правил

техники безопасности. Небрежное действие

может повлечь серьезные травмы за долюсекунды.

4) Эксплуатация электроинструмента иуход

за ним

a ) Избегайте чрезмерной нагрузки

электроинструмента. Используйте

электроинструмент всоответствии

сназначением. Правильно подобранный

электроинструмент выполнит работу более

эффективно ибезопасно при стандартнойнагрузке.

b ) Не пользуйтесь инструментом, если

не работает выключатель. Любой

инструмент, управлять выключением

ивключением которого невозможно, опасен, иего

необходимоотремонтировать.

c ) Перед выполнением любых настроек,

сменой аксессуаров или прежде чем убрать

инструмент на хранение, отключите его от

сети и/или снимите снего аккумуляторную

батарею, если ее можно снять. Такие

превентивные меры безопасности сокращают риск

случайного включенияэлектроинструмента.

d ) Храните электроинструмент внедоступном

для детей месте ине позволяйте работать

синструментом людям, не имеющим

https://tm.by

Интернет-магазин TM.by

PУССКИЙ

одну минуту. Поврежденные принадлежности,

как правило, ломаются в течение этого

тестовогопериода.

h ) Используйте средства индивидуальной

защиты. В зависимости от типа выполняемых

работ надевайте щиток для защиты лица

или защитные очки. В соответствии с

необходимостью надевайте респиратор,

защитные наушники, перчатки и рабочий

фартук, способный защитить от мелких

абразивных частиц и фрагментов

обрабатываемой детали. Средства защиты для

глаз должны останавливать частицы, вылетающие

при выполнении различных видов работ.

Пылезащитная маска или респиратор должны

обеспечивать фильтрацию твердых частиц,

образующихся при выполнении работ. Длительное

воздействие шума высокой мощности может

привести к нарушениямслуха.

i ) Не подпускайте посторонних лиц близко

к рабочей зоне. Любое лицо, входящее в

рабочую зону, должно использовать средства

индивидуальной защиты. Фрагменты

обрабатываемой детали или разрушенной

оснастки могут отлететь в сторону и стать

причиной травмы даже за пределами рабочейзоны.

j ) Удерживайте электроинструмент во время

выполнения работ только за изолированные

поверхности захватывания в тех случаях,

когда режущая принадлежность может задеть

скрытую электропроводку или собственный

кабель питания. При удерживании металлических

деталей инструмента, в случае перерезания

находящегося под напряжением провода возможно

поражение оператора электрическимтоком.

k ) Располагайте кабель питания на удалении

от вращающейся принадлежности. В

случае потери контроля над инструментом

кабель питания может быть разрезан или

ободран, а ваша рука может быть затянута

вращающейсяпринадлежностью.

l ) Никогда не кладите электроинструмент до

тех пор, пока он полностью не остановится.

Вращающаяся принадлежность может задеть за

поверхность, из‑за чего электроинструмент может

вырваться изрук.

m ) Не включайте электроинструмент, если

принадлежность направлена на вас. Случайный

контакт с вращающейся принадлежностью может

привести к наматыванию одежды и контакту

принадлежности с вашимтелом.

n ) Регулярно очищайте вентиляционные

отверстия электроинструмента. Вентилятор

электродвигателя затягивает пыль внутрь

корпуса, а скопление большого количества пыли

данному электроинструменту. Несоблюдение

всех приведенных ниже инструкций может стать

причиной поражения электрическим током,

возгорания и/или тяжелойтравмы.

b ) Не рекомендуется выполнять с помощью

данного инструмента такие работы

как полирование. Выполнение операций, не

предусмотренных для данного инструмента,

представляет опасность и может привести

ктравме.

c ) Не используйте дополнительные

принадлежности, которые не рекомендованы

производителем инструмента и не

предназначены для него специально.

Возможность установки принадлежности

на электроинструмент не обеспечивает

безопасности при ееиспользовании.

d ) Номинальная скорость принадлежности

должна, как минимум, равняться максимальной

скорости, указанной на электроинструменте.

Принадлежность, которая вращается со

скоростью, превышающей ее номинальную скорость

вращения, может разрушиться и отлететь

всторону.

e ) Внешний диаметр и толщина принадлежности

должны соответствовать диапазону

мощности электроинструмента.

Принадлежности неправильно подобранного

размера не закрываются защитным кожухом и не

обеспечивают надлежащего контроляуправления.

f ) Винтовая резьба принадлежностей

должна соответствовать резьбе оси

шлифовальной машины. Для принадлежности,

установленной на фланцы, отверстие

для инструментальной оправки должно

соответствовать установочному диаметру

фланца. Принадлежности, которые не подходят

к монтажной арматуре электроинструмента,

работают несбалансированно, слишком сильно

вибрируют и могут привести к потереконтроля.

g ) Не используйте поврежденные

принадлежности. Перед каждым

использованием проверяйте принадлежности,

как то: абразивные круги – на наличие

сколов и трещин, диск‑подошву – на

наличие надрывов, трещин или чрезмерного

износа, проволочные щетки – на наличие

ослабленной или сломанной проволоки.

В случае падения электроинструмента

или принадлежности проверьте наличие

повреждений или установите неповрежденную

принадлежность. После проверки и установки

принадлежности оператор и посторонние лица

не должны находиться на одной плоскости с

вращающейся принадлежностью. Запустите

электроинструмент на максимальной

скорости без нагрузки и дайте ему поработать

https://tm.by

Интернет-магазин TM.by

Страница загружается...

DeWalt DWE4157F Инструкция по эксплуатации

Модели других брендов