Sony DSC-T110 Руководство пользователя

GB

RU

UA

4-269-986-41(1)

DSC-T110/T110D

GB Digital Still Camera/Instruction Manual

RU Цифровой фотоаппарат/Инструкция по эксплуатации

UA Цифровий фотоапарат/Посібник з експлуатації

GB

2

Owner’s Record

The model and serial numbers are located on the bottom. Record the serial number in the

space provided below. Refer to these numbers whenever you call your Sony dealer

regarding this product.

Model No. DSC-T110/T110D

Serial No. ______________________________

To reduce fire or shock hazard, do not expose the unit to rain or

moisture.

If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the

proper configuration for the power outlet.

[ Battery pack

If the battery pack is mishandled, the battery pack can burst, cause a fire or even chemical

burns. Observe the following cautions.

• Do not disassemble.

• Do not crush and do not expose the battery pack to any shock or force such as

hammering, dropping or stepping on it.

• Do not short circuit and do not allow metal objects to come into contact with the battery

terminals.

English

WARNING

CAUTION

GB

3

GB

• Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a

car parked in the sun.

• Do not incinerate or dispose of in fire.

• Do not handle damaged or leaking lithium ion batteries.

• Be sure to charge the battery pack using a genuine Sony battery charger or a device that

can charge the battery pack.

• Keep the battery pack out of the reach of small children.

• Keep the battery pack dry.

• Replace only with the same or equivalent type recommended by Sony.

• Dispose of used battery packs promptly as described in the instructions.

[ Battery charger

Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC

power source (mains) as long as it is connected to the wall outlet (wall socket). If some

trouble occurs while using the battery charger, immediately shut off the power by

disconnecting the plug from the wall outlet (wall socket).

The power cord (mains lead), if supplied, is designed specifically for use with this camera

only, and should not be used with other electrical equipment.

[ RECYCLING LITHIUM-ION BATTERIES

Lithium-Ion batteries are recyclable.

You can help preserve our environment by returning your used

rechargeable batteries to the collection and recycling location nearest

you.

For more information regarding recycling of rechargeable batteries,

call toll free

1-800-822-8837, or visit http://www.rbrc.org/

Caution: Do not handle damaged or leaking Lithium-Ion batteries.

[ Battery pack

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

For Customers in the U.S.A. and Canada

GB

4

UL is an internationally recognized safety organization.

The UL Mark on the product means it has been UL Listed.

If you have any questions about this product, you may call:

Sony Customer Information Center

1-800-222-SONY (7669)

The number below is for the FCC related matters only.

[ Regulatory Information

[ CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual

could void your authority to operate this equipment.

For Customers in the U.S.A.

Declaration of Conformity

Trade Name: SONY

Model No.: DSC-T110, DSC-T110D

Responsible Party: Sony Electronics Inc.

Address: 16530 Via Esprillo,

San Diego, CA 92127 U.S.A.

Telephone No.: 858-942-2230

This device complies with Part15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

GB

5

GB

[ Note:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

The supplied interface cable must be used with the equipment in order to comply with the

limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

[ Notice for the customers in the countries applying EU Directives

The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo,

108-0075 Japan. The Authorized Representative for EMC and product safety is Sony

Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or

guarantee matters please refer to the addresses given in separate service or guarantee

documents.

This product has been tested and found compliant with the limits set out in the EMC

Directive for using connection cables shorter than 3 meters (9.8 feet).

[ Attention

The electromagnetic fields at the specific frequencies may influence the picture and sound

of this unit.

[ Notice

If static electricity or electromagnetism causes data transfer to discontinue midway (fail),

restart the application or disconnect and connect the communication cable (USB, etc.)

again.

For Customers in Europe

GB

6

[ Disposal of Old Electrical & Electronic Equipment (Applicable in

the European Union and other European countries with separate

collection systems)

This symbol on the product or on its packaging indicates that this product

shall not be treated as household waste. Instead it shall be handed over to

the applicable collection point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling

of this product. The recycling of materials will help to conserve natural

resources. For more detailed information about recycling of this product,

please contact your local Civic Office, your household waste disposal service or the shop

where you purchased the product.

[ Disposal of waste batteries (applicable in the European Union

and other European countries with separate collection systems)

This symbol on the battery or on the packaging indicates that the battery

provided with this product shall not be treated as household waste.

On certain batteries this symbol might be used in combination with a

chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are

added if the battery contains more than 0.0005% mercury or 0.004% lead.

By ensuring these batteries are disposed of correctly, you will help prevent

potentially negative consequences for the environment and human health which could

otherwise be caused by inappropriate waste handling of the battery. The recycling of the

materials will help to conserve natural resources.

In case of products that for safety, performance or data integrity reasons require a

permanent connection with an incorporated battery, this battery should be replaced by

qualified service staff only. To ensure that the battery will be treated properly, hand over

the product at end-of-life to the applicable collection point for the recycling of electrical

and electronic equipment.

For all other batteries, please view the section on how to remove the battery from the

product safely.

Hand the battery over to the applicable collection point for the recycling of waste batteries.

For more detailed information about recycling of this product or battery, please contact

your local Civic Office, your household waste disposal service or the shop where you

purchased the product.

A moulded plug complying with BS 1363 is fitted to this equipment for your safety and

convenience.

Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the

supplied one and approved by ASTA or BSI to BS 1362, (i.e., marked with an or

mark) must be used.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the

fuse cover after you change the fuse. Never use the plug without the fuse cover. If you

should lose the fuse cover, please contact your nearest Sony service station.

Notice for customers in the United Kingdom

GB

7

GB

Table of contents

Getting started

Refer to “Cyber-shot Handbook” (PDF) on supplied

CD-ROM.....................................................................................8

Checking the accessories supplied...........................................8

Notes on using the camera........................................................8

Identifying parts .......................................................................11

Battery charging and the number of images/time that can be

recorded .................................................................................. 12

Inserting the battery pack/a memory card (sold separately)...15

Setting the date and time/display color ...................................18

Shooting/viewing images

Shooting still images ................................................................20

Shooting movies.......................................................................21

Viewing images ........................................................................22

In-Camera Guide .....................................................................23

“Cyber-shot Handbook” (PDF)

Learning more about the camera (“Cyber-shot

Handbook”) ..............................................................................24

Others

List of icons displayed on the screen ......................................25

Number of still images and recordable time of movies ...........27

Precautions ..............................................................................29

Specifications...........................................................................31

GB

8

Checking the accessories supplied

• Battery charger BC-CSN/BC-CSNB (1)

• Power cord (mains lead) (not supplied in the USA and Canada) (1)

• Rechargeable battery pack NP-BN1 (1)

• Paint pen (1)

• USB, A/V cable for multi-use terminal (1)

• Wrist strap (1)

•CD-ROM (1)

– Cyber-shot application software

– “Cyber-shot Handbook”

• Instruction Manual (this manual) (1)

Notes on using the camera

Changing the language setting

The screen language can be changed if necessary.

To change the language setting, touch , then select (Settings) t

(Main Settings) t [Language Setting].

Internal memory and memory card back up

Do not turn off the camera, remove the battery pack, or remove the memory

card while the access lamp is lit. Otherwise, the internal memory data or the

memory card may be damaged. Be sure to make a backup copy to protect your

data.

Refer to “Cyber-shot Handbook” (PDF)

on supplied CD-ROM

For details on advanced operations, please read “Cyber-

shot Handbook” (PDF) on the CD-ROM (supplied) using

a computer.

Refer to “Cyber-shot Handbook” for in-depth instructions

on shooting or viewing images and connecting the camera

to your computer, printer or TV (page 24).

GB

9

GB

Functions built into this camera

This manual describes each of the functions of TransferJet-compatible/

incompatible devices.

To check if your camera supports the TransferJet function, check for the

following mark on the bottom of the camera.

TransferJet-compatible device: (TransferJet)

On database files

When you insert a memory card without a database file into the camera and

turn on the power, part of the memory card capacity is used to automatically

create a database file. It may take some time until you can perform the next

operation.

Notes on recording/playback

• To ensure stable operations of the memory card, we recommend that you use

this camera to format any memory card being used with this camera for the

first time. Note that formatting will erase all data recorded on the memory

card. This data cannot be restored. Be sure to backup any important data to a

PC or other storage location.

• Before you start recording, make a trial recording to make sure that the

camera is working correctly.

• The camera is neither dust-proof, nor splash-proof, nor water-proof. Read

“Precautions” (page 29) before operating the camera.

• Avoid exposing the camera to water. If water enters inside the camera, a

malfunction may occur. In some cases, the camera cannot be repaired.

• Do not aim the camera at the sun or other bright light. It may cause the

malfunction of the camera.

• Do not use the camera near a location that generates strong radio waves or

emits radiation. Otherwise, the camera may not properly record or play back

images.

• Using the camera in sandy or dusty locations may cause malfunctions.

• If moisture condensation occurs, remove it before using the camera.

• Do not shake or strike the camera. It may cause a malfunction and you may

not be able to record images. Furthermore, the recording media may become

unusable or image data may be damaged.

• Clean the flash surface before use. The heat of flash emission may cause dirt

on the flash surface to become discolored or to stick to the flash surface,

resulting in insufficient light emission.

Notes on the LCD screen

• The LCD screen is manufactured using extremely high-precision technology

so over 99.99% of the pixels are operational for effective use. However,

some tiny black and/or bright dots (white, red, blue or green) may appear on

the LCD screen. These dots are a normal result of the manufacturing process,

and do not affect the recording.

GB

10

• If water droplets or other liquids splash on the LCD screen and make it wet,

immediately wipe off the screen with a soft cloth. Leaving liquids on the

LCD screen surface can harm the quality and cause a malfunction.

• Do not press against the LCD screen. The screen may be discolored and that

may cause a malfunction.

Please use Sony genuine accessories

If you use accessories manufactured by companies other than Sony, this could

cause a camera trouble.

• Using other manufacturers’ camera cases with magnets could cause a power

supply trouble.

On camera’s temperature

Your camera and battery may get hot due to continuous use, but it is not a

malfunction.

On the overheat protection

Depending on the camera and battery temperature, you may be unable to

record movies or the power may turn off automatically to protect the camera.

A message will be displayed on the LCD screen before the power turns off or

you can no longer record movies. In such a case, wait until the camera and

battery completely cool down, with the power turned off. If you turn the power

on before they completely cool down, the power may turn off again or you

may be unable to record movies.

On battery charging

In rare cases, a battery that has not been used for a long time may not be

charged optimally. This is due to characteristics of the battery and not a

malfunction. Charge the battery again.

On image data compatibility

• The camera conforms with DCF (Design rule for Camera File system)

universal standard established by JEITA (Japan Electronics and Information

Technology Industries Association).

• Sony does not guarantee that the camera will play back images recorded or

edited with other equipment, or that other equipment will play back images

recorded with the camera.

Warning on copyright

Television programs, films, videotapes, and other materials may be

copyrighted. Unauthorized recording of such materials may be contrary to the

provisions of the copyright laws.

No compensation for damaged content or recording failure

Sony cannot compensate for failure to record or loss or damage of recorded

content due to a malfunction of the camera or recording media, etc.

GB

11

GB

Identifying parts

A Zoom (W/T) lever

B Shutter button

C Microphone

D ON/OFF (Power) button/

Power lamp

E Flash

F Self-timer lamp/Smile Shutter

lamp/AF illuminator

G Lens

H Lens cover

I LCD screen/Touch panel

J Speaker

K (Playback) button

L Hook for wrist strap

M Battery insertion slot

N Tripod receptacle

• Use a tripod with a screw less

than 5.5 mm (7/32 inches) long.

Otherwise, you cannot firmly

secure the camera, and damage to

the camera may occur.

O Battery/Memory card cover

P Multi-connector (Type3a)

Q Battery eject lever

R Memory card slot

S Access lamp

T (TransferJet™) mark

Cover panel

GB

12

Battery charging and the number of

images/time that can be recorded

1

Insert the battery pack into the

battery charger.

• You can charge the battery even when it is

partially charged.

2

Connect the battery

charger to the wall

outlet (wall socket).

If you continue charging

the battery pack for about

one more hour after the

CHARGE lamp turns off,

the charge will last slightly

longer (full charge).

CHARGE lamp

Lit: Charging

Off: Charging finished

(normal charge)

3

When charging is finished, disconnect the battery

charger.

Battery

pack

For customers in the USA and

Canada

CHARGE lamp

Power cord

(mains lead)

CHARGE lamp

Plug

For customers in countries/regions

other than the USA and Canada

GB

13

GB

x

Charging time

• The table above shows the time required to charge a fully depleted battery pack at

a temperature of 25°C (77°F). Charging may take longer depending on conditions

of use and circumstances.

• Connect the battery charger to the nearest wall outlet (wall socket).

• When charging is finished, disconnect the power cord (mains lead) and the battery

charger from the wall outlet (wall socket), and remove the battery pack from the

battery charger.

• Be sure to use the battery pack or the battery charger of the genuine Sony brand.

x

Battery life and number of images you can record/

view

• The number of images that can be recorded is an approximate number when

shooting with a fully charged battery pack. The number may be less depending on

the circumstances.

• The number of images that can be recorded is when shooting under the following

conditions:

– Using Sony “Memory Stick PRO Duo” (Mark2) media (sold separately).

– When a fully charged battery pack (supplied) is used at an ambient temperature

of 25°C (77°F).

Full charge time Normal charge time

Approx. 245 min. Approx. 185 min.

Notes

Battery life (min.) No. of Images

Shooting still

images

Approx. 115 Approx. 230

Viewing still

images

Approx. 250 Approx. 5000

Shooting movies Approx. 90 —

Notes

GB

14

• The number of still images that can be recorded is based on the CIPA standard,

and is for shooting under the following conditions.

(CIPA: Camera & Imaging Products Association)

– [LCD Brightness] is set to [Normal].

– Shooting once every 30 seconds.

– The zoom is switched alternately between the W and T ends.

– The flash strobes once every two times.

– The power turns on and off once every ten times.

• The battery life for movies is when shooting under the following conditions:

– Recording mode: 720 FINE

– When continuous shooting ends because of set limits (page 28), press the shutter

button down again and continue shooting. Shooting functions such as the zoom

do not operate.

z Using the camera abroad

You can use the camera and the battery charger (supplied) in any country

or region where the power supply is within 100 V to 240 V AC, 50 Hz/

60 Hz.

An electronic voltage transformer is unnecessary and its use may cause a

malfunction.

GB

15

GB

Inserting the battery pack/a memory card

(sold separately)

1

Open the cover.

2

Insert a memory card

(sold separately).

With the notched corner facing as

illustrated, insert the memory

card until it clicks into place.

3

Insert the battery pack.

Align the battery pack with the

guide arrow inside the battery

insertion slot. Then, insert the

battery pack until the battery eject

lever locks into place.

4

Close the cover.

• Closing the cover with the

battery inserted incorrectly may

damage the camera.

Note the notched corner

facing the correct direction.

Battery eject lever

GB

16

x

Memory card that you can use

The following memory cards are compatible with this camera: “Memory Stick

PRO Duo” media, “Memory Stick PRO-HG Duo” media, “Memory Stick

Duo” media, SD memory card, SDHC memory card and SDXC memory card.

However, all memory cards are not guaranteed to work with this camera.

MultiMediaCard cannot be used.

• In this manual, the term “Memory Stick Duo” media is used to refer to “Memory

Stick PRO Duo” media, “Memory Stick PRO-HG Duo” media and “Memory

Stick Duo” media, and the term “SD card” is used to refer to SD memory card,

SDHC memory card and SDXC memory card.

• When recording movies, it is recommended that you use the following memory

cards:

– (Mark2) (“Memory Stick PRO Duo” (Mark2) media)

– (“Memory Stick PRO-HG Duo” media)

– SD memory card, SDHC memory card or SDXC memory card (Class 4 or faster)

For details on the number of images/time that can be recorded, see page 27.

• Images recorded on an SDXC memory card cannot be transferred or played back

on computers or AV devices that are not exFAT-compatible, even when the

camera is connected to the computer or AV device using a USB cable. Before

connecting, make sure that the device is exFAT-compatible. If connected to a

device that is not exFAT-compatible, a format drive request may appear. Do not

format the drive, or all data will be lost. (exFAT is the file system used by SDXC

memory cards.)

x

To remove the memory card

• Never remove the memory card/the battery pack when the access lamp is lit. This

may cause damage to data or the memory card.

Note

Make sure that the access lamp is not lit,

then push the memory card in once.

Note

Access lamp

GB

17

GB

x

When there is no memory card inserted

Images are stored in the camera’s internal memory (approximately 23 MB).

To copy images from the internal memory to a memory card, insert a memory

card in the camera, then touch t (Settings) t (Memory

Card Tool) t [Copy].

x

To remove the battery pack

x

Checking the remaining battery charge

A remaining charge indicator appears on the LCD screen.

• It takes about one minute until the correct remaining charge indicator appears.

• The remaining charge indicator may not be correct under certain circumstances.

• When [Power Save] is set to [Standard] or [Stamina], if you do not operate the

camera for a certain period of time while the power is on, the LCD screen becomes

dark, then the camera turns off automatically (Auto power-off function).

• To keep clean battery pack terminal and prevent short-circuiting, place the battery

pack in a plastic bag, etc. when carrying and storing to isolate it from other metal

objects, etc.

Slide the battery eject lever. Be sure not

to drop the battery pack.

Notes

B

attery e

j

ect

l

ever

High Low

GB

18

Setting the date and time/display color

x

Superimposing the date on the images

The camera does not have a feature for superimposing dates on images. By

using “PMB” in the CD-ROM (supplied), you can print or save images with

the date. For details, see the “PMB Help”.

1

Lower the lens cover.

The camera is turned on. The

power lamp lights up only when

the camera starts up.

• You can also turn on the camera

by pressing the ON/OFF

(Power) button.

• It may take time for the power to

turn on and allow operation.

2

Select the desired date display format, then touch

[OK].

3

Select Daylight Savings [On]/[Off], then touch [OK].

4

Select the item to be set, then set the value with v/V

and touch [OK].

• Midnight is indicated as 12:00 AM, and noon as 12:00 PM.

5

Select your desired area with b/B, then touch [OK]

t [OK].

6

Follow the instructions on the screen to select a

desired display color and display resolution mode.

7

When the introductory message for the In-Camera

Guide appears, touch [OK].

ON/OFF (Power) button

Lens cover

GB

19

GB

x

Setting the date and time again

The date and time setup screen appears automatically only when the power is

turned on the first time. To reset the date and time, display the date and time

setup screen by touching t (Settings) t (Clock Settings) t

[Date & Time Setting].

GB

20

Shooting still images

1

Lower the lens cover.

2

Hold the camera steady as

illustrated.

• Slide the zoom (W/T) lever to the T side to

zoom.

Slide to the W side to return.

3

Press the shutter button

halfway down to focus.

When the image is in focus, a beep

sounds and the z indicator lights.

4

Press the shutter button

fully down.

Lens cover

Shutter button

AE/AF lock

Страница загружается...

Sony DSC-T110, Cyber-shot DSC-T110 Black, DSC-T110 Silver, DSC-T110D Руководство пользователя

Похожие модели бренда