Yamaha SHS-300 Инструкция по применению

Бренд: Yamaha

Модель: SHS-300

Тип: Инструкция по применению

ESFREN

Owner’s Manual

Mode d’emploi

Manual de instrucciones

Before using the instrument, be sure to read “PRECAUTIONS” on pages 5-9.

Avant d’utiliser l’instrument, lisez attentivement la section « PRÉCAUTIONS D’USAGE » aux pages 5-9.

Antes de utilizar el instrumento, lea las “PRECAUCIONES,” en las páginas 5-9.

EnglishFrançais

Español

2 SHS-300 Owner’s Manual

SPECIAL MESSAGE SECTION

This product utilizes batteries or an external power supply

(adapter). DO NOT connect this product to any power supply or

adapter other than one described in the manual, on the name

plate, or specifically recommended by Yamaha.

WARNING: Do not place this product in a position where any-

one could walk on, trip over, or roll anything over power or con-

necting cords of any kind. The use of an extension cord is not

recommended! If you must use an extension cord, the minimum

wire size for a 25’ cord (or less) is 18 AWG. NOTE: The smaller

the AWG number, the larger the current handling capacity. For

longer extension cords, consult a local electrician.

This product should be used only with the components supplied

or; a cart, rack, or stand that is recommended by Yamaha. If a

cart, etc., is used, please observe all safety markings and instruc-

tions that accompany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct

at the time of printing. However, Yamaha reserves the right to

change or modify any of the specifications without notice or obli-

gation to update existing units.

This product, either alone or in combination with an amplifier and

headphones or speaker/s, may be capable of producing sound

levels that could cause permanent hearing loss. DO NOT operate

for long periods of time at a high volume level or at a level that is

uncomfortable. If you experience any hearing loss or ringing in

the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

Some Yamaha products may have benches and / or accessory

mounting fixtures that are either supplied with the product or as

optional accessories. Some of these items are designed to be

dealer assembled or installed. Please make sure that benches

are stable and any optional fixtures (where applicable) are well

secured BEFORE using.

Benches supplied by Yamaha are designed for seating only. No

other uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to

how a function or effect works (when the unit is operating as

designed) are not covered by the manufacturer’s warranty, and

are therefore the owners responsibility. Please study this manual

carefully and consult your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and

environmentally friendly. We sincerely believe that our products

and the production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the law, we

want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery

which (if applicable) is soldered in place. The average life span of

this type of battery is approximately five years. When replace-

ment becomes necessary, contact a qualified service representa-

tive to perform the replacement.

This product may also use “household” type batteries. Some of

these may be rechargeable. Make sure that the battery being

charged is a rechargeable type and that the charger is intended

for the battery being charged.

When installing batteries, never mix old batteries with new ones,

and never mix different types of batteries. Batteries MUST be

installed correctly. Mismatches or incorrect installation may result

in overheating and battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all

batteries away from children. Dispose of used batteries promptly

and as regulated by the laws in your area. Note: Check with any

retailer of household type batteries in your area for battery dis-

posal information.

Disposal Notice:

Should this product become damaged beyond repair, or for some

reason its useful life is considered to be at an end, please

observe all local, state, and federal regulations that relate to the

disposal of products that contain lead, batteries, plastics, etc. If

your dealer is unable to assist you, please contact Yamaha

directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The

model number, serial number, power requirements, etc., are

located on this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided below

and retain this manual as a permanent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

92-BP (bottom)

SHS-300 Owner’s Manual 3

* This applies only to products distributed by Yamaha Corporation of America.

COMPLIANCE INFORMATION STATEMENT

(Supplierʼs declaration of conformity procedure)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Digital Keyboard

Model Name : SHS-300

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

(FCC SDoC)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifica-

tions not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could

void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these requirements

provides a reasonable level of assurance that your use of this

product in a residential environment will not result in harmful

interference with other electronic devices. This equipment

generates/uses radio frequencies and, if not installed and

used according to the instructions found in the users manual,

may cause interference harmful to the operation of other elec-

tronic devices. Compliance with FCC regulations does not

guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”, please

try to eliminate the problem by using one of the following mea-

sures:

Relocate either this product or the device that is being affected

by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distribute

this type of product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of America, Elec-

tronic Service Division, 6600 Orangethorpe Ave, Buena Park,

CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by Yamaha Corporation of America. (class B)

4 SHS-300 Owner’s Manual

(weee_battery_eu_en_02)

Information for users on collection and disposal of old equipment and used

batteries:

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries should not be mixed with general household

waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them

to applicable collection points, in accordance with your national legislation.

By disposing of these products and batteries correctly, you will help to save valuable resources

and prevent any potential negative effects on human health and the environment which could

otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact

your local municipality, your waste disposal service or the point of sale where you purchased the

items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier

for further information.

Information on Disposal in other Countries outside the European Union:

These symbols are only valid in the European Union. If you wish to discard these items, please

contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with

the requirement set by the EU Battery Directive for the chemical involved.

The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the bottom of the

unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase

to aid identification in the event of theft.

Model No.

Serial No.

(bottom_en_01)

SHS-300 Owner’s Manual 5

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe and

handy place for future reference.

WARNING

Always follow the basic precautions listed

below to avoid the possibility of serious

injury or even death from electrical shock,

short-circuiting, damages, fire or other

hazards. These precautions include, but

are not limited to, the following:

Power supply

• Do not place the USB cable near heat sources

such as heaters or radiators. Also, do not

excessively bend or otherwise damage the

cable, or place heavy objects on it.

• Only use the voltage specified as correct for

the instrument. The required voltage is printed

on the name plate of the instrument.

• Do not use the supplied USB cable for any

other instrument. Doing so might cause a

damage to the instrument, overheating or fire.

• Check the electric plug periodically and

remove any dirt or dust which may have

accumulated on it.

Do not open

• This instrument contains no user-serviceable

parts. Do not open the instrument or attempt to

disassemble or modify the internal

components in any way. If it should appear to

be malfunctioning, discontinue use

immediately and have it inspected by qualified

Yamaha service personnel.

Water warning

• Do not expose the instrument to rain, use it

near water or in damp or wet conditions, or

place on it any containers (such as vases,

bottles or glasses) containing liquids which

might spill into any openings. If any liquid such

as water seeps into the instrument, turn off the

power immediately and disconnect the plug

from the AC outlet. Then have the instrument

inspected by qualified Yamaha service

personnel.

• Never insert or remove an electric plug with

wet hands.

Fire warning

• Do not put burning items, such as candles, on

the unit. A burning item may fall over and

cause a fire.

Influences on electro-medical

devices

• Radio waves or magnetism may affect electro-

medical devices.

- Do not use this product near medical

devices or inside areas in which the use of

radio waves is restricted.

- Do not use this product within 15 cm (6 in.) of

persons with a heart pacemaker or

defibrillator implant.

Battery

• Follow the precautions below. Failure to do so

might result in explosion, fire, overheating or

battery fluid leakage.

- Do not tamper with or disassemble batteries.

- Do not dispose of batteries in fire.

- Do not attempt to recharge batteries that are

not designed to be charged.

- Keep the batteries separate from metallic

objects such as necklaces, hairpins, coins,

and keys.

- Use the specified battery type (page 33)

only.

- Use new batteries, all of which are the same

type, same model, and made by the same

manufacturer.

DMI-7 1/3

English

6 SHS-300 Owner’s Manual

- Always make sure all batteries are inserted in

conformity with the +/- polarity markings.

- When the batteries run out, or if the

instrument is not to be used for a long time,

remove the batteries from the instrument.

- When using Ni-MH batteries, follow the

instructions that came with the batteries. Use

only the specified charger device when

charging.

• Keep batteries away from small children who

might accidentally swallow them.

• If the batteries do leak, avoid contact with the

leaked fluid. If the battery fluid should come in

contact with your eyes, mouth, or skin, wash

immediately with water and consult a doctor.

Battery fluid is corrosive and may possibly

cause loss of sight or chemical burns.

If you notice any abnormality

• When one of the following problems occur,

immediately turn off the power switch and

disconnect the electric plug from the outlet.

(If you are using batteries, remove all batteries

from the instrument.) Then have the device

inspected by Yamaha service personnel.

- The USB cable or plug becomes frayed or

damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the

instrument.

- There is a sudden loss of sound during use

of the instrument.

- If any cracks or breakages exist on the

instrument.

CAUTION

Always follow the basic precautions listed

below to avoid the possibility of physical

injury to you or others, or damage to the

instrument or other property. These

precautions include, but are not limited to,

the following:

Power supply

• Do not connect the instrument to an electrical

outlet using a multiple-connector. Doing so

can result in lower sound quality, or possibly

cause overheating in the outlet.

• When removing the electric plug from the

instrument or an outlet, always hold the plug

itself and not the USB cable. Pulling by the

cable can damage it.

• Remove the electric plug from the outlet when

the instrument is not to be used for extended

periods of time, or during electrical storms.

• Use the specified USB power adaptor (pages

17, 33) only. Using the wrong adaptor can

result in damage to the instrument or

overheating.

Location

• Do not place the instrument in an unstable

position where it might accidentally fall over.

• Before moving the instrument, remove all

connected cables, to prevent damage to the

cables or injury to anyone who might trip over

them.

• When using an electric plug, make sure that

the AC outlet you are using is easily

accessible in plain view. If some trouble or

malfunction occurs, immediately turn off the

power switch and disconnect the plug from

the outlet. Even when the power switch is

turned off, electricity is still flowing to the

product at the minimum level. When you are

not using the product for a long time, make

sure to disconnect the plug from the wall AC

outlet.

DMI-7 2/3

SHS-300 Owner’s Manual 7

Connections

• Before connecting the instrument to other

electronic components, turn off the power for

all components. Before turning the power on

or off for all components, set all volume levels

to minimum.

• Be sure to set the volumes of all components

at their minimum levels and gradually raise the

volume controls while playing the instrument to

set the desired listening level.

Handling caution

• Do not insert your finger or hand in any gaps

on the instrument.

• Never insert or drop paper, metallic, or other

objects into the gaps on the panel or

keyboard. This could cause physical injury to

you or others, damage to the instrument or

other property, or operational failure.

• Do not rest your weight on, or place heavy

objects on the instrument, and do not use

excessive force on the buttons, switches or

connectors.

• Keep small parts out of the reach of infants.

Your children may accidentally swallow them.

• Do not use the instrument/device or

headphones for a long period of time at a high

or uncomfortable volume level, since this can

cause permanent hearing loss. If you

experience any hearing loss or ringing in the

ears, consult a physician.

• When using a strap, make sure the strap is

securely attached to the instrument.

• Do not lift the instrument by the strap. It can

cause serious injury or damage to the

instrument.

• Do not treat the instrument in a rough manner

such as swinging it about, etc. The strap on

the instrument may detach causing

unexpected accidents such as the instrument

dropping, etc., or injuring persons close by.

Always turn the power off when the instrument is

not in use.

Even when the instrument is in standby mode

([VAR] (Variation) lamp is off), electricity is still

flowing to the instrument at the minimum level.

When you are not using the instrument for a long

time, make sure you disconnect the plug from

the wall AC outlet.

Make sure to discard used batteries according to

local regulations.

Yamaha cannot be held responsible for

damage caused by improper use or

modifications to the instrument, or data that

is lost or destroyed.

DMI-7 3/3

8 SHS-300 Owner’s Manual

NOTICE

To avoid the possibility of malfunction/ damage

to the product, damage to data, or damage to

other property, follow the notices below.

 Handling

• Do not use the instrument in the vicinity of a

TV, radio, stereo equipment, mobile phone, or

other electric devices. Otherwise, the

instrument, TV, or radio may generate noise.

When you use the instrument along with an

application on your iPad, iPhone or iPod

touch, we recommend that you set “Airplane

Mode” to “ON” on the device and then the

Bluetooth

setting to “ON” in order to avoid

noise caused by communication.

• Do not expose the instrument to excessive

dust or vibrations, or extreme cold or heat

(such as in direct sunlight, near a heater, or in

a car during the day) to prevent the possibility

of panel disfiguration, damage to the internal

components or unstable operation. (Verified

operating temperature range: 5° – 40°C, or

41° – 104°F.)

• Do not place vinyl, plastic or rubber objects

on the instrument, since this might discolor

the panel or keyboard.

 Maintenance

• When cleaning the instrument, use a soft and

dry cloth. Do not use paint thinners, solvents,

alcohol, cleaning fluids, or chemical-

impregnated wiping cloths.

 Saving data

• Some of the data of this instrument (page 30)

are retained when the power is turned off.

However, the saved data may be lost due to

some failure, an operation mistake, etc.

Information

 About copyrights

• Copying of the commercially available

musical data including but not limited to MIDI

data and/or audio data is strictly prohibited

except for your personal use.

• This product incorporates and bundles

contents in which Yamaha owns copyrights or

with respect to which Yamaha has license to

use others’ copyrights. Due to copyright laws

and other relevant laws, you are NOT allowed

to distribute media in which these contents

are saved or recorded and remain virtually

the same or very similar to those in the

product.

* The contents described above include a

computer program, Accompaniment Style

data, MIDI data, WAVE data, voice

recording data, a score, score data, etc.

* You are allowed to distribute medium in

which your performance or music

production using these contents is

recorded, and the permission of Yamaha

Corporation is not required in such cases.

 About this manual

• The illustrations as shown in this manual are

for instructional purposes only, and may

appear somewhat different from those on

your instrument.

• The letters at the end of the model name

(“WH” or “BU”) are color information of the

instrument. Since they simply indicate the

color, these letters are omitted in this manual.

• Mac, iPhone, iPad, iPod touch and Lightning

are trademarks of Apple Inc., registered in

the U.S. and other countries.

• Android™ is a trademark of Google LLC.

• The Bluetooth

word mark and logos are

registered trademarks owned by Bluetooth

SIG, Inc. and any use of such marks by

Yamaha Corporation is under license.

• The company names and product names in

this manual are the trademarks or registered

trademarks of their respective companies.

SHS-300 Owner’s Manual 9

About Bluetooth

Bluetooth is a technology for wireless communication between devices within an area of about

10 meters (33 ft.) employing the 2.4 GHz frequency band.

 Handling Bluetooth communications

• The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many types of

equipment. While Bluetooth compatible devices use a technology minimizing the influence of other

components using the same radio band, such influence may reduce the speed or distance of

communications and in some cases interrupt communications.

• The speed of signal transfer and the distance at which communication is possible differs according

to the distance between the communicating devices, the presence of obstacles, radio wave

conditions and the type of equipment.

• Yamaha does not guarantee all wireless connections between this unit and devices compatible

with Bluetooth function.

Your particular instrument does not have Bluetooth capability if a “Y” indication is printed on the upper-

right corner of the label at the bottom.

SER No.

ZZZZZZZZZZ

SHS-300**

YYYYYYYYYYY

10 SHS-300 Owner’s Manual

Thank you for purchasing the Yamaha Digital Keyboard!

This instrument not only lets you enjoy playing the keyboard—even strapped around your

shoulder like a guitar—but also gives you powerful, fun tools for effortlessly playing along

with your favorite music, by connecting to the Chord Tracker smart device app.

We recommend that you read this manual carefully so that you can fully take advantage of

the advanced and convenient functions of the instrument.

We also recommend that you keep this manual in a safe and handy place for future

reference.

This instrument has the following documents and instructional materials.

Owner’s Manual (this book)

Explains how to get started with the instrument and how to use main feature

Jam function.

MIDI Reference (Online Manual)

Contains MIDI-related information for this instrument.

To obtain online manual (PDF), access the Yamaha Downloads website, then enter the

model name for searching the desired files.

• Owner’s Manual x1

• USB cable x1

•Strap x1

• Online Member Product Registration x1

About the Manuals

Yamaha Downloads

https://download.yamaha.com/

Included Accessories

SHS-300 Owner’s Manual 11

Contents

Panel Controls ................................................................................................... 12

Setting Up ........................................................................................................... 15

Try Playing a Variety of Instrument Voices ..................................................... 20

Enjoy Playing with the Jam Function............................................................... 21

Setting Up for MIDI Operation ........................................................................... 26

Customizing the Settings .................................................................................. 28

Backup and Initialization ................................................................................... 30

Troubleshooting ................................................................................................. 31

Specifications ..................................................................................................... 33

Index .................................................................................................................... 35

Drum Kit List....................................................................................................... 36

12 SHS-300 Owner’s Manual

Panel Controls

[PITCH] bend wheel

For adding smooth pitch variations to the notes you play on the keyboard. Roll the wheel toward

you to raise the pitch, or away from you to lower it. With the [FUNCTION] button, you can

change the direction of the pitch bend (page 28).

[VIBRATO] button

Press this button to add a vibrato effect to notes played on the keyboard.

[SUSTAIN] button

Press this button to sustain the notes played on the keyboard. Release it to stop the sustain.

[VAR] (Variation) lamp

Glows when the instrument is on, with the color indicating the selected Voice.

See page 20 for more details on the Voices and color indications.

[SYNTH] button

Selects one of three synthesizer Voices each time this button is pressed.

[PIANO] button

Selects one of three piano Voices each time this button is pressed.

[GUITAR] button

Selects one of three guitar Voices each time this button is pressed.

[OTHER] button

Selects one of three other Voices each time this button is pressed.

[JAM] button

With each button press, this turns on (lamp lights), selects the Jam mode in order, and then turns

off the Jam function (lamp turns off). See page 25 for more details on Jam modes.

NOTE

When the Jam mode is set to on and the instrument receives new MIDI data, the lamp flashes momentarily.

C2 D2 E2 F2 G2 A2

SHS-300 Owner’s Manual 13

[FUNCTION] button

For setting various functions. While holding down this button, press the keys corresponding to the

function settings you want to change. See page 28 for details on the functions.

VOLUME [-] button

Each button press lowers the overall volume of the instrument. Holding down the button lowers the

volume continuously.

VOLUME [+] button

Each button press raises the overall volume of the instrument. Holding down the button raises the

volume continuously.

NOTE

• The setting range is 0 – 15; the default setting is 13.

• To reset to the default setting, press the VOLUME [-] button and VOLUME [+] button simultaneously.

[] (Standby/On) button

Press this button to turn on the instrument; the [VAR] lamp lights. Press and hold this button for

more than one second to put into standby mode.

[PHONES] jack

For connecting a pair of stereo headphones or other equipment with a mini stereo phone plug

(3.5 mm). The instrument’s built-in speakers automatically stop producing sound when plugged

in. This allows you to connect, for example, to an external amplifier to drive external speakers.

CAUTION

• To prevent hearing loss, avoid using headphones at high volumes for extended periods of time.

• Before connecting the instrument to other electronic components, turn off the power of all the

components. Also, before turning any components on or off, make sure to set all volume levels to

minimum. Otherwise, damage to the components or electrical shock may occur.

B2 C3 D3 E3 F3 G3 A3 B3 C4 C5D4 E4 F4 G4 A4 B4

14 SHS-300 Owner’s Manual

[AUX IN] jack

For inputting the sound of an audio player and listening to it through the built-in speaker of the

instrument (with 3.5 mm, mini stereo phone plug). To adjust the input volume from [AUX IN] jack,

adjust the audio playback volume on the audio device.

CAUTION

To avoid possible damage, first turn on the power to the external device, then to the instrument. When

turning off the power, first turn off the power to the instrument, then to the external device.

NOTE

• Use an appropriate adaptor plug if the output jack of the audio device does not match the stereo mini phone

plug of the audio cable.

• Use audio cables and adaptor plugs that have no series resistors.

5V DC-IN / USB TO HOST terminal

For connection to a USB power adaptor, USB mobile battery (page 17), or smart device (page 23)

with a USB cable. The instrument uses this connection to send and receive MIDI data when

connected to a smart device or computer (page 26).

Side

SHS-300 Owner’s Manual 15

Setting Up

Attach the included strap securely to the strap pins of the instrument as illustrated below.

The strap has an adjuster allowing you to adjust it as desired.

CAUTION

• This strap is designed for use with only this instrument. Do not use for any other purpose.

• When using the strap, make sure the strap is securely attached to the instrument.

• Do not lift the instrument by the strap. Doing so can cause damage to the instrument or injury.

• Never loosen the screws mounting the strap pins.

Attaching the Strap

Adjuster

SHS-300 bottom

Strap pin

16 SHS-300 Owner’s Manual

This instrument can be powered in one of the two ways listed below.

Determine which you intend to use, and follow the instructions for setting up.

• Using batteries (sold separately)  next section (below)

• Using a USB power adaptor or USB mobile battery (sold separately)  see

page 17

NOTICE

• Use only the USB cable supplied with the instrument. Using the wrong USB cable can result in sound drop

outs.

• Make sure that the instrument’s power is turned off (the [VAR] lamp is off) before connecting the instrument.

Using Batteries

This instrument requires four “AA” size, Alkaline (LR6)/ Manganese (R6) batteries, or rechargeable

nickel-metal hydride batteries (rechargeable Ni-MH batteries).

1. Make sure that the power of the instrument is off.

The [VAR] lamp will be off when the power is off.

2. Open the battery compartment cover located on the instrument’s bottom panel.

3. Insert the four new batteries, being careful to follow the polarity markings on the

inside of the compartment.

4. Replace the compartment cover, making sure that it locks firmly in place.

5. Setting the battery type.

Power on the instrument. While holding down the [FUNCTION] button, press the B3 key (page 29).

Each key press switches the battery type. The presses produce a lower pitch beep for non-

chargeable dry cell batteries (alkaline and manganese type) or a higher pitch beep for

rechargeable batteries (Ni-MH type).

Power Requirements

SHS-300 Owner’s Manual 17

NOTICE

• Failure to set the battery type may shorten the life of the battery. Make sure to set the battery type

correctly.

• Connecting or disconnecting the USB cable with batteries installed may turn the power off, resulting in

loss of your custom settings data.

• When battery power becomes too low for proper operation, the volume may be reduced, the sound

may be distorted, and other problems may occur. When this happens, make sure to replace all

batteries with new ones or already recharged ones.

NOTE

• This instrument cannot be used to charge the batteries. Use only the specified charger device when

charging.

• Power will be automatically drawn from the USB cable if a USB cable is connected while batteries are

installed in the instrument.

Using a USB power adaptor or USB mobile battery (sold separately)

Connect the USB cable to a separately sold USB power adaptor or USB mobile battery in the order

shown in the illustration.

Follow the order shown above in reverse when disconnecting the USB cable.

CAUTION

• Before using a USB power adaptor or USB mobile battery, be sure to read the relevant precautions.

• Use only a USB power adaptor or USB mobile battery compatible with the USB standard for power

supply.

Output voltage 4.8 V to 5.2 V

Output current 1.0 A or greater

SHS-300

USB cable

USB power adaptor

USB mobile battery

AC outlet

*The shape of the plug differs depending on your area.

18 SHS-300 Owner’s Manual

1. Press the [] (Standby/On) button to turn the power on.

The [VAR] lamp is lit in red when the power is on.

Adjust the volume as desired while playing the keyboard.

CAUTION

Do not use the instrument or headphones for a long period of time at a high or uncomfortable volume

level, since this can cause permanent hearing loss.

NOTICE

While turning on the power, do not attempt any other operations, such as pressing the keys. Doing so

may cause the instrument to malfunction.

2. Press and hold the [ ] (Standby/On) button for longer than one second to enable

standby mode.

CAUTION

Even when in standby mode, electric current is still flowing to the instrument at the minimum level. When

you are not using the instrument for a long time, make sure to disconnect the USB power adaptor from

the AC outlet, or remove batteries from the instrument.

Turning on the Power / Setting to Standby

If the overall volume is low, or no sound is heard, please confirm “Troubleshooting” on page 31.

[VAR] lamp

1. Power on

Adjust the volume

SHS-300 Owner’s Manual 19

Enabling / Disabling Auto Power Off

To prevent unnecessary power consumption, this instrument features an Auto Power Off function that

automatically turns the power off if the instrument is not operated for a specified period of time

(30 minutes). With default, it is set to On, however, the setting can be changed with the [FUNCTION]

button (page 29).

Disabling Auto Power Off

1. When the instrument is turned on, turn off the power.

2. Turn the power back on while holding down the lowest key on the keyboard.

Enabling Auto Power Off

To enable the Auto Power Off function, change the setting via the Function mode (page 29) or initialize

the instrument (page 30).

NOTICE

• Some of the data of this instrument (page 30) are retained when the power is turned off.

• If your instrument is connected to other equipment such as amplifiers and speakers but you do not intend

to use it for 30 minutes, we recommend that you turn off all devices as described in the corresponding

owner’s manuals. Doing so eliminates the risk of damage to the other equipment. If you do not want the

instrument to turn off automatically when connected to other equipment, disable the Auto Power Off

function.

20 SHS-300 Owner’s Manual

Try Playing a Variety of Instrument Voices

You can change the keyboard Voice to another instrument Voice, such as strings, electric piano and

others.

1. Press the Voice button corresponding to the desired category.

Each press on one of the four Voice buttons alternates among the three Voices assigned to that

button.

Voice list

NOTE

• The list above conveniently includes program change numbers (PC No.), which you should use when playing the

instrument via MIDI from an external device.

• Program change numbers are often specified as numbers “0 – 127.” Since this list uses a “1 – 128” numbering

system, in some cases it may be necessary to subtract 1 from the actually transmitted program change numbers

to select the appropriate sound. For example, to select No. 83 in the list above, actually transmit program change

number 82.

• The Dance Kit Voice independently assigns various drum and percussion sounds to each key for playing on the

keyboard. Details on the instruments and key assignments of each Drum Kit can be found in the Drum Kit List on

page 36.

Selecting and Playing a Voice

Voice

Yamaha SHS-300 Инструкция по применению

Бренд: Yamaha

Модель: SHS-300

Тип: Инструкция по применению

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha SHS-300 Owner's manual
français: Yamaha SHS-300 Le manuel du propriétaire
italiano: Yamaha SHS-300 Manuale del proprietario
español: Yamaha SHS-300 El manual del propietario
Deutsch: Yamaha SHS-300 Bedienungsanleitung
Nederlands: Yamaha SHS-300 de handleiding
português: Yamaha SHS-300 Manual do proprietário
dansk: Yamaha SHS-300 Brugervejledning
polski: Yamaha SHS-300 Instrukcja obsługi
čeština: Yamaha SHS-300 Návod k obsluze
svenska: Yamaha SHS-300 Bruksanvisning
Türkçe: Yamaha SHS-300 El kitabı
suomi: Yamaha SHS-300 Omistajan opas
română: Yamaha SHS-300 Manualul proprietarului

Yamaha SHS-300 Инструкция по применению

Yamaha SHS-300 Инструкция по применению

на других языках

Похожие модели бренда

Модели других брендов