Indesit PWE 71271 S (EU) Руководство пользователя

Категория
Стиральные машины
Тип
Руководство пользователя
1
GB
WASHING MACHINE
Instructions for use
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and advice, 5
General safety
Disposal
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9
Table of programmes and wash cycles
Wash options
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Troubleshooting, 11
Service, 12
English, 1
GB
PWE 71271 S
UK
Українська,25
CIS
Русский,13
2
GB
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they contain
vital information relating to the safe installation
and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with the
installation process.
3 . R e m o v e t h e 4
protective screws (used
during transportation)
and the rubber washer
with the corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furniture
cabinets or anything else.
2. If the floor is not
p e r f e c t l y l e v e l ,
c o m p e n s a t e f o r
any unevenness by
tightening or loosening
the adjustable front
feet (see figure); the
angle of inclination,
measured in relation
to the worktop, must
not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it
to a cold water tap
using a ¾ gas threaded
connection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2 . C o n n e c t t h e
i n l e t h o s e t o t h e
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand side
of the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct or
a wall drain located at a
height between 65 and
100 cm from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening
the duct supplied to
the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum
power load of the appliance as indicated in the
Technical data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see
opposite);
the socket is compatible with the plug of
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washing machine has been installed,
the electricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced
by authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, using the wash cycle 2.
65 - 100 cm
Technical data
Model
PWE 71271 S
Dimensions
width 59.5 cm
height 85 cm
depth 55 cm
Capacity
from 1 to 7 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water
connections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1200 rotations per minute
Test wash
cycles in
accordan-
ce with
directives
1061/2010
and
1015/2010.
Programme
:
Cotton Standard 60°.
Programme :
Cotton Standard 40°.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2002/96/EC
4
GB
Care and maintenance
2. Unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may trickle
out. This is perfectly
normal.
3. Clean the inside thoroughly.
4. Screw the lid back on.
5. Reposition the panel, making sure the hooks
are securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose could
easily split open.
! Never use second-hand hoses.
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system inside
the washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it
and during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
Cleaning the detergent dispenser
drawer
To remove the drawer,
press lever (1) and pull
the drawer outwards (2)
(see figure).
Wash it under running
water; this procedure
should be repeated
frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into the
protective pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. Take off the cover
panel on the front of
the machine by first
pressing it in the centre
and then pu shin g
downwards on both
sides until you can
remove it (see figures).
2
1
1
2
3
5
GB
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning
and user maintenance shall not be made by
children without supervision.
The washing machine must only be used by adults, in
accordance with the instructions provided in this manual.
Do not touch the machine when barefoot or with wet or
damp hands or feet.
Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
Do not open the detergent dispenser drawer while the
machine is in operation.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
Always keep children well away from the appliance while
it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
Before loading laundry into the washing machine, make
sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
6
GB
Description of the washing
machine
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button and indicator
light
DISPLAY
DELAYED
START
button
OPTION
buttons and
indicator lights
DOOR
LOCKED
indicator light
Detergent dispenser drawer: used to dispense
detergents and washing additives ( see “Detergents and
laundry”).
ON/OFF button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light which
flashes slowly in a blue colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of programmes and wash
cycles”).
OPTION buttons and indicator lights: press to select the
available options. The indicator light corresponding to the
selected option will remain lit.
SPIN button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
TEMPERATURE button: press to reduce or
completely exclude the temperature; the value appears on
the display.
DELAYED START button: press to set a delayed start
for the selected wash cycle; the delay period appears on
the display.
START/PAUSE button and indicator light: when the
blue indicator light flashes slowly, press the button to start
a wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
amber colour. If the symbol is not illuminated, the door
may be opened (wait approximately 3 minutes). To start
the wash cycle from the point at which it was interrupted,
press the button again.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent
any damage, wait until the symbol turns off before opening
the door (wait approximately 3 minutes).
To open the door while a cycle is in progress, press the
START/PAUSE button; if the DOOR LOCKED symbol is
switched off the door may be opened.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly and
wait for the machine to start up again.
Consumption in off-mode: 0,5 W
Consumption in Left-on: 0,5 W
7
GB
Display
B
C
A
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED
START option has been set, the countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
The hour-glass flashes while the machine is processing data, depending on the wash cycle and level selected. After
a maximum of 10 minutes, the “hour-glass” icon remains lit in a fixed manner and the final amount of time remaining is
displayed. The hour-glass icon will then switch off approximately 1 minute after the final amount of time remaining has
appeared.
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle
appear in section B:
Main wash
Rinse
Spin
Drain
The icons corresponding to “temperature”, “spin” and “delayed start” (working from the left) are displayed in section C.
The “temperature” bars indicate the maximum temperature level which may be selected for the set cycle.
The “spin” bars indicate the maximum spin level which may be selected for the set cycle.
The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.
8
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
blue colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modify the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Modify the cycle settings.
Press the button to enable the option; the indicator
light corresponding to the button will switch on.
Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! If the selected option is not compatible with
a previously selected one, the indicator light
corresponding to the first function selected will flash and
only the second option will be activated; the indicator
light for the option which has been activated will be
illuminated.
Note: if the option has been selected, none of the
incompatible options may be activated.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn blue, remaining lit in a fixed manner, and the door
will be locked (the DOOR LOCKED symbol will be lit).
To change a wash cycle while it is in progress, pause
the washing machine using the START/PAUSE button
(the START/PAUSE indicator light will flash slowly in an
amber colour); then select the desired cycle and press
the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened (wait
approximately 3 minutes). Press the START/PAUSE
button again to restart the wash cycle from the point at
which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may be
opened (wait approximately 3 minutes). Open the door,
unload the laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
9
GB
Wash cycles and options
Table of programmes and wash cycles
Wash options
The PRIME technology optimises energy, water and time consumption
according to the quantity of garments actually inserted in the machine.
Moreover, pressing the button allows for selecting the following options:
- Water: allows for reducing water consumption without having to
renounce impeccable results (recommended for heavily soiled garments).
- Energy: automatically selected by PRIME, this option reduces energy
consumption (recommended for normally soiled garments).
- Time: allows for reducing wash cycle duration (recommended for lightly
soiled garments).
! This may only be used in conjunction with wash cycles 1, 2, , , 5,
6 (all three levels) and 7, 8, 9, 10 (- Energy and - Time levels).
Extra Rinse
By selecting this option, the efficiency of the rinse is increased and optimal
detergent removal is guaranteed. It is particularly useful for sensitive skin.
! It cannot be used in conjunction with wash cycles 9, .
Easy iron
By selecting this function, the wash and spin cycles will be modified in order to
reduce the formation of creases. At the end of the cycle the washing machine
will perform slow rotations of the drum, while the EASY IRON and START/
PAUSE indicator lights will flash (blue and orange respectively). To end the
cycle, press the START/PAUSE button or the EASY IRON button.
For wash cycles number 12-14, the machine will end the cycle while the
laundry is soaking; the EASY IRON and START/PAUSE indicator lights
will flash. To drain the water so that the laundry may be removed, press
the START/PAUSE button or the EASY IRON button.
! It cannot be used in conjunction with wash cycles 9, 11, 13, , .
Stain removal
This function is particularly useful for
the removal of stubborn stains. Insert
extra compartment 4 (supplied with
the appliance) into compartment 1.
When pouring in the bleach, be careful
not to exceed the max level marked
on the central pivot (see figure). To
bleach laundry with no other washing
action, pour the bleach into extra
compartment 4, select the Rinse
cycle and activate theStain
removal option . To bleach during a wash cycle, pour in the detergent and
any fabric softener you wish to use, select the desired wash cycle and enable
theStain removal option. The use of extra compartment 4 excludes the
pre-wash function.
! It cannot be used in conjunction with wash cycles 1, 7, 9, 11, 12, 13, 14, .
4
2
3
1
4
2
1
3
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
Wash cycles
Description of the wash cycle
Max.
temp.
C)
Max.
speed
(rpm)
Detergents
Max. load (kg)
Residual
dampness %
Energy
consumption
kWh
Total water lt
Cycle duration
Prewash
Wash
Bleach
Fabric
softener
Daily Programs
1
Cottons with Pre-wash: extremely soiled whites. 90° 1200
-
7 53 2,21 78 170
2
White Cottons: extremely soiled whites. 90° 1200 -
7 53 2,16 72 160
Standard Cotton 6 (1): heavily soiled whites and resistant colours. 60° 1200 -
7 53 1,26 52,5 190’
Standard Cotton 4 (2): lightly soiled whites and delicate colours. 40° 1200 -
7 53 1,09 92 185
5
Synthetics: heavily soiled resistant colours. 60° 800 -
3,5 44 0,93 47 115’
5
Synthetics (3): lightly soiled resistant colours. 40° 800 -
3,5 44 0,57 46 100’
6
Synthetics: lightly soiled resistant colours. 40° 800 -
3,5 - - - 75’
7 Jeans
40° 800 -
-
3,5 - - - 75’
8 Shirts
40° 600 -
2 - - - 70’
9
Mix-Cool 30’: to refresh lightly soiled garments quickly (not suitable for wool, silk and
clothes which require washing by hand).
Cold
water
800 -
-
3 71 0,04 34 30’
10
Standard Cotton 2: lightly soiled whites and delicate colours. 20° 1200 -
7 - - - 170’
Special
11
Wool: for wool, cashmere, etc. 40° 800 -
-
1,5 - - - 70’
12
Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0 -
-
1 - - - 55’
13 Sport Shoes
30° 600 -
-
Max.2
paires
- - - 60’
14 Outwear
30° 400 -
- - 2 - - - 60’
Partials
Rinse - 1200 - -
7 - - - 36’
Spin + Drain - 1200 - - - - 7 - - - 16’
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should
be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should
be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle
with a temperature of 40°C.
3) Synthetic program along: set wash cycle 5 with a temperature of 40°C.
10
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
Compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra
compartment 4 has been removed.
Compartment 2: Washing detergent (powder or
liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
Compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Extra compartment 4: Bleach
Extra compartment 5: we recommend this
compartment is used for liquid detergent.
Preparing the laundry
Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
Empty all garment pockets and check the buttons.
Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1.200 g
1 towel 150-250 g
Special wash cycles
Jeans: turn the garments inside out before washing and use
liquid detergent. Use wash cycle 7.
Shirts: use special wash cycle 8 to wash shirts in various
fabrics and colours. It guarantees maximum care is taken of
the garments and minimises the formation of creases.
Mix-Cool 30’: this wash cycle was designed to wash lightly
soiled garments quickly: it lasts just 30 minutes and therefore
saves both energy and time. By selecting wash cycle 9, it is
possible to wash different fabrics (except for wool and silk
items) using a cold cycle, up to a maximum load of 3 kg.
Cotton Standard 20° (wash cycle 10) ideal for heavily soiled
cotton loads. The effective performance levels achieved at
cold temperatures, which are comparable to washing at 40°,
are guaranteed by a mechanical action which operates at
varying speed, with repeated and frequent peaks.
Wool: the wool wash cycle of this machine has been
tested and approved by The Woolmark Company for the
washing of wool containing garments labelled as “hand
wash” provided that the garments are washed according
to the instructions on the garment label and those issued
by the manufacturer of this washing machine. (M1126)
In UK, Eire, Hong Kong and India the Woolmark trade mark
is a Certification trade mark.
Silk: use special wash cycle 12 to wash all silk
garments. We recommend the use of special detergent
which has been designed to wash delicate clothes.
Curtains: we recommend you fold the curtains and place
them in a pillow case or mesh bag. Use wash cycle 12.
Sport Shoes (wash cycle 13): is for washing sports shoes;
for best results, do not wash more than 2 pairs simultaneously
Outwear (wash cycle 14): is studied for washing water-
repellent fabrics and winter jackets (e.g. Gore-Tex, polyester,
nylon); for best results, use a liquid detergent and dosage
suitable for a half-load; pre-treat necks, cuffs and stains if
necessary; do not use softeners or detergents containing
softeners. Stuffed duvets cannot be washed with this
programme..
1
2
3
5
4
11
GB
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water (the text “H2O” flashes
on the display).
The washing machine
continuously takes in and drains
water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
Theoption and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display
(e.g.: F-01, F-..).
There is too much foam.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or not enough to make
contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
The free end of the hose is under water (see “Installation”).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
The wash cycle does not include draining: some cycles require the draining
process to be enabled manually.
The EASY IRON option is enabled: To complete the wash cycle, press the
START/PAUSE button (see “Wash cycles and options”).
The drain hose is bent (see “Installation”).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see “Installation”).
The washing machine is not level (see “Installation”).
The washing machine is trapped between cabinets and walls (see “Installation”).
The water inlet hose is not screwed on properly (see “Installation”).
The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
The drain hose is not fixed properly (see “Installation”).
Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the text “for
washing machines” or “hand and machine wash”, or the like).
Too much detergent was used.
12
GB
Service
Before contacting the Technical Assistance Service:
Check whether you can solve the problem alone (seeTroubleshooting”).
Restart the wash cycle to check whether the problem has been solved.
If this is not the case, contact an authorised Technical Assistance Centre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
13
CIS
Русский
CIS
СТИРАЛЬНАЯ МАШИНА
Содержание
Монтаж, 14-15
Распаковка и выравнивание
Подключение к водопроводной и электрической сети
Первый цикл стирки
Технические данные
Описание стиральной машины, 16-17
Консоль управления
Дисплей
Цикл стирки, 18
Программы и дополнительные функции, 19
Таблица программ
Дополнительные функции мойки
Стиральные порошки и белье, 20
Ячейка для стирального порошка
Подготовка белья
Специальные программы
Предосторожности и рекомендации, 21
Общие требования по безопасности
Утилизация
Техническое обслуживание и уход, 22
Отключение воды и электрического тока
Порядок чистки стиральной машины
Чистка ячейки для стирального порошка
Уход за люком и барабаном
Порядок чистки насоса
Проверка шланга подачи воды
Неисправности и методы их устранения, 23
Сервисное обслуживание, 24
PWE 71271 S
Руководство по эксплуатации
14
CIS
Установка
! Сохраните данное руководство. Оно должно быть в
комплекте со стиральной машиной в случае продажи,
передачи оборудования или при переезде на новую
квартиру, чтобы новый владелец оборудования мог
ознакомиться с правилами его функционирования и
обслуживания.
! Внимательно прочитайте руководство: в нем
содержатся важные сведения по установке и
безопасной эксплуатации стиральной машины.
Распаковка и выравнивание
Распаковка
1. Распакуйте стиральную машину.
2. Убедитесь, что оборудование не было повреждено
во время транспортировки. При обнаружении
повреждений – не подключайте машину –
свяжитесь с поставщиком немедленно.
3. Удалите четыре
транспортировочных
винта и резиновые
пробки с прокладками,
расположенные в задней
части стиральной
машины (см. рис.).
4. Закройте отверстия прилагающимися
пластиковыми заглушками.
5. Сохраняйте все детали: они Вам понадобятся
при последующей транспортировке стиральной
машины.
! Не разрешайте детям играть с упаковочными
материалами.
Выравнивание
1. Установите стиральную машину на ровном и
прочном полу, так чтобы она не касалась стен,
мебели и прочих предметов.
2. После установки
машины на место
отрегулируйте ее
устойчивое положение
путем вращения
передних ножек (см.
рис.). Для этого сначала
ослабьте контргайку,
после завершения
регулировки контргайку
затяните.
После установки машины на место проверьте по уровню
горизонтальность верхней крышки корпуса, отклонение го-
ризонтали должно быть не более 2°.
Правильное выравнивание оборудования поможет
избежать шума, вибраций и смещений во время работы
машины.
Если стиральная машина стоит на полу, покрытом
ковром, убедитесь, что ее основание возвышается
над ковром. В противном случае вентиляция будет
затруднена или вовсе невозможна.
Подключение к водопроводной и
электрической сети
Подсоединение заливного шланга
1. дачи к крану холодной
воды с резьбовым
отверстием 3/4 gas (см.
схему).
Перед подсоединением
откройте водопроводный
кран до тех пор, пока из
него не потечет чистая
вода.
2. Подсоедините
заливной шланг к
стиральной машине,
навинтив его на
водоприемник,
расположенный в задней
верхней части справа
(см. рис.).
3. Убедитесь, что шланг не перекручен и не пережат.
! Давление воды должно быть в пределах значений,
указанных в таблице Технических характеристик.
! Если длина водопроводного шланга окажется
недостаточной, обратитесь в Авторизованный
cервисный центр.
! Никогда не используйте шланги, бывшие в
употреблении.
15
CIS
Присоединение сливного шланга
Подсоедините сливной
шланг, не сгибая его, к
сливному трубопроводу
или к настенному сливу,
расположенному на
высоте 65 – 100 см от
пола.
или поместите конец
шланга в раковину или
в ванну, прикрепив
прилагающуюся
направляющую к крану
(см. схему). Свободный
конец сливного шланга
не должен быть
погружен в воду.
! Не рекомендуется использовать удлинительные
шланги. При необходимости удлинение должно иметь
такой же диаметр, что и оригинальный шланг, и его
длина не должна превышать 150 см.
Электрическое подключение
Перед подсоединением штепсельной вилки изделия к
сетевой розетке необходимо проверить следующее:
сетевая розетка должна быть заземлена и
соответствовать нормативам;
сетевая розетка должна быть расчитана на
максимальную мощность стиральной машины,
указанную в таблице Технические данные (см.
таблицу сбоку);
напряжение электропитания должно
соответствовать значениям, указанным в таблице
Технические данные (см. таблицу сбоку);
сетевая розетка должна быть совместимой со
штепсельной вилкой стиральной машины. В
противном случае необходимо заменить сетевую
розетку или штепсельную вилку.
! Запрещается устанавливать стиральную машину на
улице, даже под навесом, так как является опасным
подвергать ее воздействию дождя и грозы.
! Стиральная машина должна быть расположена
таким образом, чтобы доступ к сетевой розетке
оставался свободным.
! Не используйте удлинители и тройники.
! Сетевой кабель изделия не должен быть согнут или сжат.
! Замена сетевого кабеля может осуществляться
только уполномоченными техниками.
Внимание! Компания-производитель снимает с себя
всякую ответственность в случае несоблюдения
вышеописанных правил.
65 - 100 cm
Первый цикл стирки
По завершении установки, перед началом
эксплуатации необходимо произвести один цикл
стирки со стиральным веществом, но без белья, по
программе 2.
Технические данные
Модель PWE 71271 S
Страна-
изготовитель
Италия
Габаритные
размеры
ширина 59,5 см.
высота 85 см.
глубина 55 см.
Вместимость от 1 до 7 кг
Номинальное
значение
напряжения
электропитания
или диапазон
напряжения
220-240 V ~
Условное
обозначение рода
электрического тока
или номинальная
частота
переменного тока
50 Hz
Класс зашиты
от поражения
электрическим
током
Класс защиты I
Водопроводное
подсоединение
максимальное давление 1 МПа (10 бар)
минимальное давление 0,05 МПа (0,5 бар)
емкость барабана 52 литра
Скорость отжима до 1200 оборотов в минуту
Программы
управления в
соответствии с
Директивой
EN 60456
программа
; температура 60°C;
загрузка 7 кг белья.
Данное изделие соответствует
следующим Директивам Европейского
Сообщества:
- 2004/108/СЕ (Электромагнитная
совместимость);
- 2006/95/CE (Низкое напряжение)
- 2002/96/CE
В случае необходимости получения
информации по сертификатам
соответствия или получения копий
сертификатов соответствия на данную
технику, Вы можете отправить запрос
по электронному адресу cert.rus@
indesit.com.
Дату производства
данной техники
можно получить из
серийного номера,
расположенного
под штрих-кодом
(S/N XXXXXXXXX),
следующим
образом
- 1-ая цифра в S/N соответствует
последней цифре года,
- 2-ая и 3-я цифры в S/N -
порядковому номеру месяца года,
- 4-ая и 5-ая цифры в S/N - день
Степень защиты от попадания твердых частиц и влаги,
обеспечиваемая защитной оболочкой, за исключением
низковольтного оборудования, не имеющего защиты от влаги: IPX04
Класс
энергопотребления
A
16
CIS
Описание стиральной машины
Консоль управления
Кнопка
ТЕМПЕРАТУРА
РУКОЯТКА
ВЫБОРА
ПРОГРАММ
Ячейка для стирального вещества
Кнопка ON/OFF
Кнопка ОТЖИМ
Кнопка с индикатором
START/PAUSE
ДИСПЛЕЙ
Кнопка ТАЙМЕР
ОТСРОЧКИ
Кнопки с индикаторами
ФУНКЦИИ
Индикатор ЛЮК
ЗАБЛОКИРОВАН
Ячейки для стирального вещества: для загрузки
стиральных веществ и добавок (см. “Стиральные
вещества и типы белья”).
Кнопка ON/OFF : быстро нажмите эту кнопку для
включения или выключения машины. Индикатор
START/PAUSE, редко мигающий синим цветом,
означает, что машина включена. Для выключения
стиральной машины в процессе стирки необходимо
держать нажатой кнопку, примерно 3 секунды.
Короткое или случайное нажатие не приведет к
отключению машины.
В случае выключения машины в процессе стирки
текущий цикл отменяется.
РУКОЯТКА ВЫБОРА ПРОГРАММ: служат для
выбора нужной программы (см. “Таблица программ”).
Кнопки и индикаторы ДОПОЛНИТЕЛЬНЫЕ
ФУНКЦИИ: служат для выбора имеющихся
дополнительных функций. Индикатор,
соответствующий выбранной функции , останется
включенным.
Кнопка ОТЖИМ : нажмите эту кнопку для
сокращения скорости или полного исключения
отжима – значение показывается на дисплее.
Кнопка ТЕМПЕРАТУРА : нажмите эту кнопку для
сокращения температуры или полного исключения
нагрева – значение показывается на дисплее.
Кнопка ТАЙМЕР ОТСРОЧКИ : нажмите эту кнопку
для программирования задержки запуска выбранной
программы; время задержки показывается на
дисплее.
Кнопка и индикатор START/PAUSE : когда синий
индикатор редко мигает, нажмите кнопку для запуска
цикла стирки. После пуска цикла индикатор перестает
мигать. Для прерывания стирки вновь нажмите эту
кнопку; индикатор замигает оранжевым цветом.
Если символ не горит, можно открыть люк машины
(ожидайте приблиз. 3 минуты). Для возобновления
стирки с момента, когда она была прервана, вновь
нажмите эту кнопку.
Индикатор ЛЮК ЗАБЛОКИРОВАН
Включенный символ означает, что люк заблокирован.
Во избежание повреждений, перед тем как открыть
люк, необходимо дождаться, пока погаснет этот
символ (ожидайте приблиз. 3 минуты).
Если требуется открыть люк после запуска цикла,
нажмите кнопку START/PAUSE. Когда погаснет индикатор
ЛЮК ЗАБЛОКИРОВАН , можно открыть люк.
Режим ожидания
Настоящая стиральная машина отвечает требованиям
новых нормативов по экономии электроэнергии,
укомплектована системой автоматического отключения
ежим сохранения энергии), включающейся через 30
минут простоя машины. Нажмите один раз кнопку
ON/OFF и подождите, пока машина вновь включится.
17
CIS
Дисплей
B
C
A
Дисплей служит для программирования машины и предоставляет пользователю множество сведений.
В секторе A показывается продолжительность различных имеющихся программ и, после запуска цикла, время,
остающееся до завершения программы. Если был задан ТАЙМЕР ОТСРОЧКИ, на дисплее показывается время,
остающееся до запуска выбранной программы.
Кроме того при нажатии соответствующей кнопки на дисплее показываются максимальные значения скорости
отжима и температуры, которые машина может достичь в зависимости от заданной программы, или последние
заданные значения, если они совместимы с выбранной программой.
В процессе обработки данных машиной в зависимости от программы и от выбранного уровня мигает символ
“песочные часы”. Максимум через 10 минут после запуска символ “песочные часы” перестает мигать и горит
стабильно, показывая окончательное остаточное время. Символ “песочные часы” погаснет примерно через 1
минуту после визуализации окончательного остаточного времения.
В секторе B показываются фазы стирки выбранной программы стирки и, после запуска программы, текущую фазу
программы:
Стирка
Полоскание
Отжим
Слив
В секторе C показываются слева направо символы “температура”, “отжим” и “таймер отсрочки”.
Полоски “температуры” показывают максимальный температурный уровень, который может быть задан для
выбранной программы.
Полоски “отжима” показывают максимальную скорость отжима, которая может быть задана для выбранной
программы.
Включенный символ “ТАЙМЕР ОТСРОЧКИ” означает, что на дисплее показано заданнное значение “таймер
отсрочки”.
18
CIS
Порядок выполнения цикла стирки
1. ПОРЯДОК ВКЛЮЧЕНИЯ МАШИНЫ. Нажмите
кнопку ; индикатор START/PAUSE редко мигает
синим цветом.
2. ЗАГРУЗКА БЕЛЬЯ. Откройте люк машины.
Загрузите в барабан белье, не превышая
максимальный допустимый вес, указанный в
таблице программ на следующей странице.
3. ДОЗИРОВКА СТИРАЛЬНОГО ВЕЩЕСТВА
Выньте дозатор и поместите стиральное вещество
в специальные ячейки, как описано в разделе
Стиральные вещества и типы белья”.
4. ЗАКРОЙТЕ ЛЮК.
5. ВЫБОР ПРОГРАММЫ. При помощи рукоятки
выбора ПРОГРАММ выберите нужную программу;
в данной программе задана температура и
скорость отжима, которые можно изменить. На
дисплее показывается продолжительность данного
цикла.
6. ПЕРСОНАЛИЗИРОВАННЫЕ ЦИКЛЫ СТИРКИ.
Нажмите соответствующие кнопки:
Измените температуру и/или скорость
отжима. Машина автоматически показывает на
дисплее максимальные температуру и скорость
отжима, предусмотренные для выбранной
программы, или последние выбранные значения,
если они совместимы с выбранной программой.
При помощи кнопки можно постепенно
уменьшить температуру вплоть до стирки в
холодной воде “OFF”. При помощи кнопки
можно постепенно уменьшить скорость отжима
вплоть до его исключения “OFF”. При еще одном
нажатии этих кнопок вернутся максимальные
допустимые значения.
Программирование таймера отсрочки
Для программирования пуска выбранной
программы с задержкой нажмите соответствующую
кнопку вплоть до получения нужного времени
задержки. Когда данная дополнительная функция
активирована, на дисплее загорается символ
. Для отмены запуска с задержкой нажмите кнопку
несколько раз до тех пор, пока на дисплее не
появится “OFF”.
Измените параметры цикла.
Нажмите кнопку для активации дополнительной
функции; индикатор соответствующей кнопки
загорится.
Вновь нажмите кнопку для отключения
дополнительной функции, индикатор погаснет.
! Если выбранная дополнительная функция
является несовместимой с заданной программой,
индикатор будет мигать, и такая функция не будет
активирована.
! Если выбраная дополнительная функция
несовместима с ранее активированной
функцией, индикатор соответствующий первой
активированной функции функции замигает,
и будет активирована только вторая функция,
индикатор активированнойфункциизагорится .
Примечание: если активирована дополнительная
функция , никакая другая дополнительная
функция не может быть активирована.
! Дополнительные функции могут изменить
рекомендуемую загрузку машины и/или
продолжительность цикла.
7. ЗАПУСК ПРОГРАММЫ Нажмите кнопку START/
PAUSE. Соответствующий индикатор загорится
синим светом, и люк заблокируется (символ ЛЮК
ЗАБЛОКИРОВАН загорится). Для изменения
программы в процессе выполнения цикла
переключите машину в режим паузы при помощи
кнопки START/PAUSE (индикатор START/PAUSE
редко мигает оранжевым цветом). Затем выберите
новый цикл и вновь нажмите кнопку START/PAUSE.
Если требуется открыть люк после пуска цикла,
нажмите кнопку START/PAUSE. Когда погаснет
индикатор ЛЮК ЗАБЛОКИРОВАН , можно
открыть люк (ожидайте приблиз. 3 минуты). Вновь
нажмите кнопку START/PAUSE для возобновления
программы с момента, в который она была
прервана.
8. ЗАВЕРШЕНИЕ ПРОГРАММЫ. Показывается
сообщением “на дисплее “END”. После того, как
погаснет символ ЛЮК ЗАБЛОКИРОВАН , можно
будет открыть люк (ожидайте приблиз. 3 минуты).
Откройте люк, выгрузите белье и выключите
машину.
! Если требуется отменить текущий цикл стирки,
держите нажатой кнопку несколько секунд. Цикл
прервется, и машина выключится.
19
CIS
Дополнительные функции стирки
Технология «PRIM оптимизирует потребление энергии, воды
и затраты времени в зависимости от типа белья. Опцию можно
выбрать нажатием кнопки .
- Water (Экономия Bодa): позволяет уменьшить потребление
воды, обеспечивая безупречный результат (рекомендуется
для белья с высокой степенью загрязнения).
- Energy (Экономия Электрознeргня): автоматическая
опция технологии «PRIM снижает энергопотребление
(рекомендуется для белья с нормальной степенью загрязнения).
- Time (Экономия емя): обеспечивает сокращение времени
стирки (рекомендуется для белья с низкой степенью загрязнения).
! Эта функция может быть активирована только для
программ 1, 2, , , 5, 6 (для всех трех уровней) и 7, 8,
9, 10 (уровни - Energy и - Time).
Дополнительное полоскание
При выборе этой функции повышается эффективность
ополаскивания, обеспечивая максимальное удаление
стирального вещества. Эта функция особенно удобна для
людей с кожей, чувствительной к стиральным веществам.
! Не может быть активирована в программах 9, .
Легкая глажка
При выборе этой функции циклы стирки и отжима изменяются
таким образом, чтобы сократить сминаемость белья. По
завершении цикла машина производит медленное вращение
барабана. Индикатор функции Легкая глажка и индикатор
START/PAUSE мигают (первый синим, второй оранжевым цветом).
Для завершения цикла нажмите кнопку START/PAUSE или
кнопку Легкая глажка. При выборе программы 12-14 машина
завершает цикл без слива воды, и индикатор фукции Легкая
глажка и индикатор START/PAUSE мигают. Для слива воды
и выгрузки белья необходимо нажать кнопку START/PAUSE
или кнопку Легкая глажка.
! Не может быть активирована в программах 9, 11, 13, , .
Функция пятновыведения
Эта функция служит для удаления
наиболее трудных пятен. Вставьте
дополнительный прилагающийся
дозатор 4 в дозатор 1.
При
заливе отбеливателя не
превышайте макс. уровень,
указанный на стержне в центре
(см. схему). Для выполнения
только отбеливания
залейте отбеливатель в
дополнительный дозатор
4, выберите программу “Полоскание” и включите
дополнительную функцию Пятновыведение” .
Для отбеливания
в процессе стирки поместите стиральное вещество и добавки,
выберите нужную программу и активируйте дополнительную функцию
Пятновыведение .
Если используется дополнительный дозатор
4, функция предварительная стирка исключается.
! Не может быть активирована в программах 1, 7, 9, 11, 12,
13, 14, .
Таблица программ
4
2
3
1
4
2
1
3
Программы и дополнительные
функции
Описание программы
Макс.
темп.
(°C)
Макс.
скорость
(оборотов в
минуту)
Стиральные вещества и добавки
Макс.
загру-
зка (кг)
Прод-
олжитть
цикла
Предв-
арительная
мойка
Стирка
Отбели-
ватель
Ополаски-
ватель
Ежедневные
Продолжительность программ стирки можно проверять по дисплею.
1
Хлопок: с замачиванием
90° 1200
-
7
2
Хлопок: интенсивная
90° 1200 -
7
Хлопок (1): ñèëüíîçàãðÿçí¸ííîå áåëîå è ïðî÷íî
îêðàøåííîå öâåòíîå áåëü¸.
60° 1200 -
7
Хлопок (2):
î÷åíü ãðÿçíîå áåëîå è äåëèêàòíîå öâåòíîå áåëüå.
40° 1200 -
7
5
Синтетика: интенсивная
60° 800 -
3,5
6
Синтетика: бережная
40° 800 -
3,5
7
Джинсы
40° 800 -
-
3,5
8
Рубашки
40° 600 -
2
9
MixCool 30': Для быстрого освежения малогрязного белья
(не для шерсти, шелка и изделия ручной стирки).
холодная
вода
800 -
-
3
10
Хлопок:
î÷åíü ãðÿçíîå áåëîå è äåëèêàòíîå öâåòíîå áåëüå.
20° 1200 -
7
Специальные
11
Шерсть: шерсть, кашемир и т.д.
40° 800 -
-
1,5
12
Шелк: изделия из шелка, вискозы и нижнее белье.
30° 0 -
-
1
13
Спортивная обувь
30° 600 -
-
(ìàêñ.
2 ïàðû.)
14
 
30° 400 -
- -
2
Дополнителые
Полоскание
- 1200 - -
7
Отжим + Слив
- 1200 - - - - 7
Программы
Для всех институтов тестирования:
1) Программы управления в соответствии с Директивой EN 60456: задайте программу с температурой 60°C.
2) Длинная программа для х/б белья: задайте программу с температурой 40°C.
Продолжительность цикла, показанная на дисплее или указанная в инструкциях является рассчетом, сделанным на основании стандартных условий. Фактическая
продолжительность может варьировать в зависимости от многочисленных факторов таких как температура и давление воды на подаче, температура помещения, количество
моющего средства, количество и тип загруженного белья, балансировка белья, выбранные дополнительные функции.
20
CIS
Стиральные вещества и
типы белья
Ячейка для стирального вещества
Хороший результат стирки зависит также от
правильной дозировки стирального вещества:
избыток стирального вещества не гарантирует
более эффективную стирку, напротив, способствует
образованию налетов внутри стиральной машины и
загрязнению окружающей среды.
! Не используйте стиральные вещества для ручной
стирки, так как они образуют слишком много пены.
Выньте ячейку и поместите
в нее стиральное
вещество или добавку в
следующем порядке.
Ячейка 1: Стиральное
ввещество для
предварительной стирки
(порошок)
Перед засыпкой
стирального порошка необходимо проверить, чтобы
не был установлен дополнительный дозатор 4.
Ячейка 2: Стиральное вещество для стирки
(порошок или жидкий)
Жидкое средство для стирки заливается
непосредственно перед запуском машины.
Ячейка 3: Добавки (ополаскиватель и т.д.)
Не наливайте ополаскиватель выше решетки
дозатора.
дополнительный дозатор 4: Отбеливатель
дополнительный дозатор 5: рекомендуется
использовать этот дозатор для жидкого стирального
вещества.
Подготовка белья
Разделите белье по следующим признакам:
- тип ткани / обозначения на этикетке
- цвету: отделите цветное белье от белого.
Выньте из карманов все предметы и проверьте
пуговицы.
Не превышайте значения, указанные в «Таблице
программ», указывающие вес сухого белья.
Сколько весит белье?
1 простыня 400-500 гр.
1 наволочка 150-200 гр.
1 скатерть 400-500 гр.
1 халат 900-1200 гр.
1 полотенце 150-250 гр.
Специальные программы
Джинсы: выверните наизнанку изделия перед стиркой
и используйте жидкое моющее средство. Используйте
программу 7.
Рубашки: используйте специальную программу 8 для
стирки рубашек из разных тканей и разных расцветок.
Это обеспечит максимальную сохранность вещей и
сократит их сминаемость.
1
2
3
5
4
MixCool 30 (программа 9): предназначена для
быстрой стирки слабозагрязненного белья цикл
длится всего 30 минут, что позволяет сэкономить
время и электроэнергию. По этой программе
(9, 30°C) можно стирать вместе белье из разных тканей
а исключением шерсти и шелка) с максимальной
загрузкой 3 кг.
ÕËÎÏÎK (программа 10) белья стандартная программа
идеально подходит для стирки х/б белья со средним
загрязнением. Отличные результаты получаются также
при стирке в холодной воде, сравнимые со стиркой при
40°, обеспечиваются механическим действием с разной
скоростью с повторяющимися частыми пиками.
Шерсть: Цикл стирки “Шерсть» данной стиральной
машины прошел тестирование и был утвержден
Компанией Woolmark Company для стирки изделий, в
состав которых входит шерсть, классифицированных
как «для ручной стирки» с тем, чтобы тирка выполнялась
в соответствии с инсрукциями на этикетке вещи и
инструкциями, прилагаемым изготовителем данной
стиральной машины. (M1126)
Шелк: используйте специальную программу 12
для стирки всех шелковых вещей. Рекомендуется
использовать специальное стиральное вещество для
деликатных тканей.
Занавески: рекомендуется свернуть их и поместить
в прилагающийся мешок. Используйте программу 12.
Спортивная обувь (программа 13): разработана для
стирки спортивной обуви; для достижения лучших
результатов не рекомендуем стирать более 2 пар обуви
за один раз.
Верхняя одежда (программа 14) разработана для
стирки водоотталкивающих тканей и ветровок (напр.,
goretex, полиэстер, нейлон); для достижения лучших
результатов используйте жидкие моющие средства
в соответствующей дозировке для полузагрузки;
обработайте предварительно манжеты, воротники и
участки с пятнами; не используйте смягчитель или
моющие средства со смягчителем. Эта программа не
предназначена для стирки пуховиков.
Система балансировки белья
Перед каждым отжимом во избежание чрезмерных
вибраций и для равномерного распределения
белья в барабане машина производит вращения
со скоростью, слегка превышающей скорость
стирки. Если после нескольких попыток белье
не будет правильно сбалансировано, машина
произведет отжим на меньшей скорости по
сравнению с предусмотренной. В случае чрезмерной
разбалансировки машина выполнит распределение
белья вместо отжима. Для оптимизации
распределения белья и его правильной балансировки
рекомендуется перемешать мелкое белье с крупным.
1 / 1

Indesit PWE 71271 S (EU) Руководство пользователя

Категория
Стиральные машины
Тип
Руководство пользователя

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ

Спросите документ

на других языках