Yamaha Clavinova PF P-100 Руководство пользователя

OWNER’S MANUAL

P-100

FCC INFORMATION (U.S.A.)

1.

IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to use the product.

2.

IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in

the USA.

3.

NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in

harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the

instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations

does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by

turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can

not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA

90620

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

Dette apparat overholder det gaeldende EF-direktiv

vedrørrende radiostørj.

Cet appareil est conforme aux prescriptions de la direc-

tive communautaire 87/308/CEE.

Diese Geräte entsprechen der EG-Richtlinie

82/499/EWG und/oder 87/308/EWG.

This product complies with the radio frequency

interference requirements of the Council Directive

82/499/EEC and/or 87/308/EEC.

Questo apparecchio è conforme al D.M.13 aprile 1989

(Direttiva CEE/87/308) sulla soppressione dei radio-

disturbi.

Este producto está de acuerdo con los requisitos sobre

interferencias de radio frequencia fijados por el Consejo

Directivo 87/308/CEE.

YAMAHA CORPORATION

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue:

NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug, proceed as follows: The wire which

is coloured BLUE must be connected to the terminal which is

marked with the letter N or coloured BLACK. The wire

which is coloured BROWN must be connected to the termi-

nal which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth ter-

minal of the three pin plug.

CANADA

THIS DIGITAL APPARATUS DOES NOT EXCEED THE

"CLASS B" LIMITS FOR RADIO NOISE EMISSIONS

FROM DIGITAL APPARATUS SET OUT IN THE RADIO

INTERFERENCE REGULATION OF THE CANADIAN

DEPARTMENT OF COMMUNICATIONS.

LE PRESENT APPAREIL NUMERIQUE N´EMET PAS DE

BRUITS RADIOELECTRIQUES DEPASSANT LES LIMITES

APPLICABLES AUX APPAREILS NUMERIQUES DE LA

"CLASSE B" PRESCRITES DANS LE REGLEMENT SUR LE

BROUILLAGE RADIOELECTRIQUE EDICTE PAR LE

MINISTERE DES COMMUNICATIONS DU CANADA.

* This applies only to products distributed by YAMAHA

CANADA MUSIC LTD.

Litiumbatteri!

Bör endast bytas av servicepersonal.

Explosionsfara vid felaktig hantering.

VAROITUS!

Lithiumparisto, Räjähdysvaara.

Pariston saa vaihtaa ainoastaan alan

ammattimies.

ADVARSEL!

Lithiumbatteri!

Eksplosionsfare. Udskiftning má kun foretages

af en sagkyndig, – og som beskrevet i

servicemanualen.

SPECIAL MESSAGE SECTION

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these

graphics appears on this page. Please observe all cautions

indicated on this page and those indicated in the safety in-

struction section.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVING TO

QUALIFIED SERVICE PERSONNEL.

The exclamation point within the

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servicing)

instructions in the literature accompany-

ing the product.

The lightning flash with arrowhead

symbol within the equilateral triangle is

intended to alert the user to the presence

of uninsulated “dangerous voltage”

within the product’s enclosure that may

be of sufficient magnitude to constitute a

risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic products

arc tested and approved by an independent safety testing

laboratory in order that you may be sure that when it is

properly installed and used in its normal and customary

manner all forcecable risks have been eliminated. DO NOT

modify this unit or commission others to do so unless

specifically authorized by Yamaha. Product performance

and/or safety standards may be diminished. Claims filed

under the expressed warranty may be denied if the unit

is/has been modified. Implied warranties may also be

affected.

SPECIFICATIONS SUBJECT TO CHANGE: The infor-

mation contained in this manual is believed to be correct at

the time of printing. However. Yamaha reserves the right

to change or modify any of the specifications without

notice or obligation to update existing units.

ENVIRONMENTAL ISSUES: Yamaha strives to produce

products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargeable battery which (if applicable) is soldered in

place. The average life span of this type of battery is

approximately five years. When replacement becomes

necessary, contact a qualified service representative to per-

form the replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice: Should this product become damaged be-

yond repair or for some reason its useful life is considered

to be at an end please observe all local, state, and federal

regulations that relate to the disposal of products that

contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed), are not covered by the manu-

facturer’s warranty,and are therefore the owners

responsibility. Please study this manual carefully and con-

sult your dealer before requesting service.

NAME PLATE LOCATION: The graphic below indicates

the location of the name plate. The model number, serial

number, power requirements, etc., are located on this plate.

You should record the model number, serial number, and

the date of purchase in the spaces provided below and retain

this manual as a permanent record of your purchase.

92-469

IMPORTANT

SAFETY AND INSTALLATION INSTRUCTIONS

INFORMATION RELATING TO POSSIBLE PERSONAL INJURY, ELECTRIC SHOCK, AND

FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.

WARNING —

When using any electrical or electronic

product, basic precautions should always be followed.

These precautions include, but are not limited to, the

following:

1.

Read all Safety Instructions, Installation

Instructions, Special Message Section items, and any

Assembly Instructions found in this manual BEFORE

making any connections, including connection to the

main supply.

2. Main Power Supply Verification: Yamaha products

are manufactured specifically for the supply voltage in

the area where they are to be sold. If you should move,

or if any doubt exists about the supply voltage in your

area, please contact your dealer for supply voltage

verification and (if applicable) instructions. The re-

quired supply voltage is printed on the name plate. For

name plate location, please refer to the graphic found

in the Special Message Section of this manual.

3. This product may be equipped with a polarized plug

(one blade wider than the other). If you are unable to

insert the plug into the outlet, turn the plug over and

try again. If the problem persists, contact an electri-

cian to have the obsolete outlet replaced. Do NOT de-

feat the safety purpose of the plug.

4. Some electronic products utilize external power sup-

plies or adapters. DO NOT connect this type of prod-

uct to any power supply or adapter other than one

described in the owners manual, on the name plate, or

specifically recommended by Yamaha.

5. WARNING: Do not place this product or any other

objects on the power cord or place it in a position

where anyone could walk on, trip over, or roll any-

thing over power or connecting cords of any kind. The

U

se of an extension cord is not recommended! If you

must

U

se an extension cord, the minimum wire size for

a 25’ cord (or less) is 18 AWG. NOTE: The smaller

the AWG number, the larger the current handling

capacity. For longer cxtcnsion cords, consult a local

electrician.

6. Ventilation: Electronic products, unless specifically

designed for enclosed installations, should be placed in

locations that do not interfere with proper ventila-

tion. If instructions for enclosed installations are not

provided, it must be assumed that unobstructed venti-

lation is required.

7. Temperature considerations: Electronic products

should be installed in locations that do not signifi-

cantly contribute to their operating temperature.

Placement of this product close to heat sources such

as: radiators, heat registers and other devices that pro-

duct heat should be avoided.

8. This product was NOT designed for use in wet/damp

locations and should not be used near water or exposed

to rain. Examples of wet/damp locations are: near a

swimming pool, spa, tub, sink, or wet basement.

9. This product should be used only with the components

supplied or; a cart, rack, or stand that is recommended

by the manufacturer. If a cart, rack, or stand is used.

please observe all safety markings and instructions

that accompany the accessory product.

10. The power supply cord (plug) should be disconnected

from the outlet when electronic products are to be left

unused for extended periods of time. Cords should

also be disconnected when there is a high probability

of lightening and/or electrical storm activity.

11. Care should be taken that objects do not fall and

liquids are not spilled into the enclosure through any

openings that may exist.

12. Electrical/electronic products should be serviced by a

qualified service person when:

a.

The power supply cord has been damaged; or

b. Objects have fallen, been inserted, or liquids have been

spilled into the enclosure through openings; or

c.

The product has been exposed to rain; or

d. The product does not operate, exhibits a marked change

in performance; or

c. The product has been dropped, or the enclosure of the

product has been damaged.

13. Do not attempt to service this product beyond that

described in the user-maintenance instructions. All

other servicing should be referred to qualified service

personnel.

14. This product, either alone or in combination with an

amplifier and headphones or speaker/s, may be capable

of producing sound levels that could cause permanent

hearing loss. DO NOT operate for a long period of

time at a high volume level or at a level that is uncom-

fortable. If you experience any hearing loss or ringing

in the ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the

time period before damage occurs.

15. Some Yamaha products may have benches and/or acces-

sory mounting fixtures that are either supplied as a

part of the product or as optional accessories. Some of

these items are designed to be dealer assembled or in-

stalled. Please make sure that benches are stable and

any optional fixtures (where applicable) are well

secured BEFORE using Benches supplied by Yamaha

are designed for seating only No other uses are

recommended.

PLEASE KEEP THIS MANUAL

92-469-2

THANK YOU! ... for purchasing the Yamaha Clavinova PF Series P-100. The P-100 is a high-performance

electronic piano with ten voices and a host of functions that make it an ideal instrument for professional

stage and studio applications, as well as for use at home. Its features include the following:

ll

High quality AWM sound

The P-100 features a selection of ten voices and a

maximum simultaneous note output of 32 poly-

phonic notes. All of the voices were recorded us-

ing the latest sampling techniques, then processed

using Yamaha’s patented AWM sound generation

technology.

ll

Superior piano sound

Among the P-100’s voices are two authentic piano

sounds that are samples of actual acoustic instru-

ments. One is a grand piano sound, with rich bass

tones and sparkling high notes that capture the

natural reverb characteristics of a real grand piano.

The other is a bright contemporary piano that will

make a perfect addition to any band.

ll

Digital signal processing

The P-100 has a built-in digital signal processor

unit that provides full stereo reverb, chorus,

symphonic, and tremolo effects, as well as an

easy-to-control three-band equalizer that lets you

tailor the P-100’s sound to suit your taste.

ll

Touch-sensitive keyboard

The P-100’s full-sized 88-note piano keyboard

incorporates Yamaha’s Action Effect keyboard

technology, which gives it the feel and response of

a real piano keyboard. You can even adjust the

keyboard’s sensitivity to suit your playing style,

selecting from Normal, Soft, Hard, or Fixed

settings.

ll

Dual and Split voice modes

The P-100 features Dual and Split voice modes

that let you play combinations of two voices

at once. In Split mode, the key transpose values

can even be set independently for each voice.

The P-100 thus gives you a wide range of perfor-

mance flexibility in a single piano keyboard.

ll

MIDI control capability

The P-100 offers many of the control features

found on a MIDI master keyboard: velocity sensi-

tivity, pitch bend and modulation wheels, an

assignable data slider, program change send and

receive capabilities, and MIDI transpose and

MIDI merge functions. Also, in addition to jacks

for sustain, soft, and sostenuto pedals, the P-100

gives you the option of connecting a MIDI foot

controller that can be assigned in the same manner

as the continuous slider.

CONTENTS

PRECAUTIONS

....................................................

1

INTRODUCING THE

P-100

................................

2

Upper panel

.........................................................

2

Rear panel ............................................................

4

SETTING UP THE

P-100

.....................................

5

PLAYING THE DEMO

SONGS

..........................

6

PLAYING THE P-100

...........................................

7

Selecting a voice

..................................................

7

Using the reverb effect

........................................

9

Using the modulation

effects

...............................

10

Adjusting the equalization

...................................

11

DUAL MODE

........................................................

12

Selecting voices

in Dual mode

............................

12

Adjusting the voice balance

................................

13

Detuning the voices

.............................................

14

SPLIT MODE

........................................................

15

Entering Split mode

.............................................

15

Selecting voices in Split mode

............................

16

Changing the split point

......................................

17

ADJUSTING THE

KEYBOARD

........................

19

Tuning the P-100

.................................................

19

Selecting a velocity curve

....................................

20

Using the transpose function

...............................

21

Setting the transpose

amount

...............................

22

Transposing in Dual and Split modes

..................

23

MIDI KEYBOARD CONTROL

FUNCTIONS

.......................................................

25

What is MIDI?

.....................................................

25

The P-100’s MIDI

configuration

.........................

27

Enabling MIDI

transmission

...............................

29

Selecting a MIDI

velocity curve

.........................

29

Using the

MIDI

transpose function

.....................

30

MIDI UTILITY MODE SETTINGS

...................

31

MIDI Utility mode

...............................................

31

Transmit and receive

channels

............................

32

Local control

........................................................

34

MIDI merge

.........................................................

35

Bulk protect

.........................................................

36

Pitch bend range

..................................................

37

Modulation wheel

................................................

38

Assignable

controllers .........................................

39

Program change transmit table

............................

40

Program change receive table

..............................

42

SPECIAL OPERATIONS

.....................................

44

Bulk dumps

..........................................................

44

Memory

initialization ..........................................

45

SYSTEM APPLICATIONS

..................................

46

Using the P-100 with a tone generator

................ 46

Using the P-100 with another MIDI

keyboard

..........................................................

47

Using the P-100 in an extended MIDI

system

..............................................................

48

Using the P-100 with a MIDI data

recorder

............................................................

49

ERROR MESSAGES

............................................

50

SPECIFICATIONS

...............................................

51

INDEX

....................................................................

52

MIDI DATA FORMAT

.........................................

54

MIDI IMPLEMENTATION

CHART .................

58

Clavinova PF P-100 Operation Guide

PLAYING THE DEMO SONGS

PLAYING THE P-100

DUAL MODE

SPLIT MODE

ADJUSTING THE KEYBOARD

MIDI KEYBOARD CONTROL FUNCTIONS

MIDI UTILITY MODE SETTINGS

SPECIAL OPERATIONS

PRECAUTIONS

The P-100 is a fine musical instrument composed of sensitive mechanisms and delicate digital circuitry. To ensure a

long lifetime of reliable service, observe these precautions when installing, moving, or handling the P-100.

l l

Location

Do not use the P-100 in locations where it will be

exposed to direct sunlight, extremes of tempera-

ture or humidity, or excessive dust or vibration.

l l

Handling

Avoid rough handling. Do not drop the P-100 or

subject it to shock, as these can damage the

piano’s internal circuitry. Also, do not apply

excessive force to controls or terminals. When

moving the P-100. first unplug the AC power cord

and all other cables to prevent damage to cords

and jacks. When removing plugs from terminals,

always grip them directly rather than pulling on

the cords.

l l

Cleaning

Use a slightly moist cloth and a neutral cleanser to

clean the P-100. Do not use abrasive cleaners,

waxes, solvents, or chemically treated cloths to

clean the P-100, as these may damage the cabi-

net’s finish or dull the keys.

l l

AC Power

The power requirement of your P-100 has been set

to match the mains power supply voltage in your

area. Make sure that your local AC mains voltage

matches the voltage specified on the name plate

on the rear panel of your P-100. If you have any

doubts about voltage compatibility. please consult

your local Yamaha dealer. If you plan to use your

P-100 in an area with a different voltage. be sure

to use an appropriate converter.

l l

Electromagnetic interference

Avoid using your P-100 near televisions. radios. or

other equipment generating electromagnetic fields.

Proximity to such equipment can cause the P-100

to malfunction. and may generate interference

noise in the other appliance as well.

l

Extended disuse

Electrical storms can cause power surges which

can damage the P-100’s circuitry even if the

power switch is turned off. Therefore, it is best to

disconnect the P-100’s power cord from the AC

outlet when you will not be using it for an

extended period of time.

l

Service and Modification

The P-100 contains no user serviceable parts.

Never open the piano’s cabinet or tamper with it in

any way, as doing so can result in electrical shock

or damage to the P-100. Refer all servicing to

qualified YAMAHA service personnel.

l

Backup battery

The P-100’s internal settings are preserved by a

lithium backup battery which has a life of approxi-

mately 5 years. (The battery’s life may be some-

what shorter, depending on the time elapsed

between your P- 100’s date of manufacture and the

date you purchased it.) When the battery charge

runs low, the “Er1” error message will appear in

the LED display. If this display appears. save any

settings you may want to keep using the bulk

dump procedure, if possible, then contact your

Yamaha dealer or a Yamaha service center to have

the battery replaced.

1

INTRODUCING THE P-100

Upper panel

[POWER] switch

[TRANSPOSE (DETUNE)] button

This switch turns the P-100’s power supply on and

off. When the power is turned on, the number of

the voice last selected will appear in the LED

display

and the LED above the corresponding

[VOICE/UTILITY] button will light.

[VOLUME] slider

This slider controls the overall volume of sound

output from the speakers

as well as that output

via the LINE OUT jacks

on the rear panel of

the P-100. Move the slider up to increase the

volume, or down to decrease the volume.

[CS (DATA ENTRY)] slider

This continuous slider can be assigned to control

data transmission for a variety of MIDI functions.

It is also used to select a desired value when

changing P-100 settings other than the current

voice selection.

[SPLIT (BALANCE)] button

This button turns the Split voice mode on and off.

and allows you to make settings related to Split

mode operation. Also. in Dual or Split modes.

it can be used in combination with the [DATA

ENTRY] slider

to adjust the balance between

the main and sub voices.

The [TRANSPOSE] button turns the transpose

function on and off, and lets you make settings

related to this function. In Dual mode, it can be

used to adjust the detune amount.

[MIDI (TUNE)] button

This button enables the P-100’s transmission of

MIDI messages. You will use it to select the MIDI

Utility mode functions, and to transmit the P-100’s

current settings to another MIDI device as a MIDI

bulk dump. It is also used to adjust the P-100’s

tuning and select keyboard velocity curve settings.

LED display

This three-digit numeric LED display shows the

current main voice selection in Single, Dual, and

Split modes. It also shows the values of various

parameters when you change the P-100’s settings.

[VOICE/UTILITY] buttons

These buttons let you select the voices you wish to

play in Single. Dual. and Split modes. They are

also used together with the [MIDI] button

to

select the MIDI utility functions.

2

[REVERB (-1)] button

This button is used to change the reverb type and

depth. It is also used to lower Utility mode and

transpose function settings one step at a time.

[MODULATION (+1)] button

This button lets you change the modulation effect

type and depth. Also, you can use it to raise Utility

mode and transpose function settings one step at a

time.

[EQUALIZER] sliders

These sliders adjust the level of the sound output

by the P-100 in three bands: high, middle, and

low. In Dual and Split modes, the changes you

make will affect both voices being played.

PHONES jack

You can connect a stereo headphone set to the

P-100 using this jack. The speakers

will turn

off automatically when you plug in your head-

phones.

[PITCH] wheel

This wheel bends the pitch of notes you play up or

down, returning automatically to the center posi-

tion when you release it. It also transmits pitch

bend messages to other instruments when MIDI

transmission is enabled. Both voices are bent in

Dual mode. In Split mode, only the main voice is

affected. A Utility mode function lets you change

the pitch bend range to any value within a range of

one octave.

[MODULATION] wheel

This wheel applies a vibrato effect to the notes

you play when you roll it upward. (This effect

does not apply to the two acoustic piano voices.)

It also transmits modulation messages to other

instruments when MIDI transmission is enabled.

Both voices are modulated in Dual mode: only the

main voice is affected in Split mode.

Keyboard

This 88-note Action Effect keyboard simulates the

action and response of an acoustic piano key-

board.

Speakers

The P-100’s two built-in 13 cm speakers each pro-

vide an output of 20 watts. If you wish, you can

turn the speakers off using the SPEAKER switch

on the rear panel.

3

Rear panel

SPEAKER switch

This switch lets you turn off the internal speakers

mounted on the upper panel. It does not affect

the output from the LINE OUT jacks

LINE IN jacks

You can use these jacks to input line-level signals

from another instrument, such as a drum machine,

tone generator, or synthesizer, which you wish to

play through the P-100’s built-in speakers. Use the

L/MONO jack when connecting only a single line.

LINE OUT jacks

These jacks output line-level signals which can be

fed into an external amplifier, mixer, or other

audio device. Use the L/MONO jack if your audio

equipment has only one input.

Pedal jacks

These jacks let you connect up to three foot pedals

and use them as sustain, sostenuto, and soft

pedals. A single FC4 pedal is included with your

P-100. If you wish to purchase additional foot

pedals, be sure to use only Yamaha models FC4 or

FC5.

4

FOOT CONTROLLER jack

This jack allows you to connect a foot controller

(Yamaha FC7, available separately) for use as an

auxiliary controller. The foot controller can be as-

signed to a variety of MIDI functions in the same

manner as the [DATA ENTRY] slider

MIDI terminals

These terminals allow the P-100 to communicate

with other MIDI devices. To control the P-100 us-

ing a sequencer or another keyboard, connect the

device in question to the MIDI IN jack. To control

another device (such as a synthesizer or tone

generator) using the P-100, connect the device to

the MIDI OUT jack. The MIDI THRU jack sim-

ply echoes the data the P-100 receives from the

MIDI IN jack, and is used to connect three or

more MIDI devices in series.

SETTING UP THE P-100

To prepare the P-100 for playing, follow the steps below to set it up and connect any peripheral equipment.

1.

Plug in the power cord.

6.

Connect MIDI devices.

Plug the P-100’s power cord into an AC outlet.

Do not turn on, the [POWER] switch until you

have finished making all of the connections below.

Connect the P-100 to other devices using the

MIDI terminals on the rear panel. Some examples

of MIDI system connections are given on pages

46 through 49.

2.

Connect the sustain pedal.

To use the supplied FC4 footswitch as a sustain

pedal, insert its plug in the SUSTAIN jack on the

rear panel. If you have purchased additional FC4

or FC5 footswitches, you should connect them to

the SOSTENUTO and SOFT jacks at this time.

3.

Connect a foot controller.

If you have purchased an FC7 foot controller for

use as a MIDI foot controller, insert the plug of

the switch in the FOOT CONTROLLER jack on

the rear panel.

4.

Connect external amplifiers.

If you wish to amplify the P-100 through an exter-

nal audio system, connect the amplifiers to the

LINE OUT jacks on the rear panel. Use the

L/MONO jack for mono output, or both jacks for

stereo output.

5.

Connect other external audio equipment.

To amplify a device which outputs line-level audio

signals (such as a drum machine, tone generator,

or synthesizer) through the P-100’s built-in

speakers, connect cables from the output jacks of

the device in question to the LINE IN jacks on the

rear panel. Use the L/MONO jack for mono input,

or both jacks for stereo input.

7.

Connect headphones.

To listen to your P-100 through headphones,

connect a stereo headphone set to the PHONES

jack on the front panel. The built-in speakers will

turn off automatically whenever headphones are

connected to this jack.

8.

Attach the music stand.

Attach the supplied music stand to the P-100 by

inserting it into the groove along the rear edge of

the upper panel. You can set the music stand at

any desired position along the groove.

5

PLAYING THE DEMO SONGS

Your P-100 is programmed with two songs that demonstrate the instrument’s capabilities. You might want to try

playing these songs to set the volume level and make sure that everything is working properly after you finish setting

up the P-100. To do so, follow the steps below.

6

1.

Turn on the P-100.

Move the [VOLUME] slider down to a low level, then press the

[POWER] switch to turn on the P-100. If you have connected

your P-100 to an external amplifier, you should turn the amplifi-

er on after the P-100 in order to avoid damaging the speakers.

2.

Enter Demo Play mode.

Press the [-1] and [+l] buttons simultaneously. The letter “d”

appear in the display, followed by a pair of dashes.

3.

Play a demo song.

Press the [+l] button once to select the first demo song, or twice

to select the second song. The song you select will begin

playing.

If you press the [+l] button three times, the word “all” will

appear in the display and the P-100 will play all two demo

songs in an endless loop.

If you don’t press the [+l] button within three seconds, the

P-100 will automatically exit the Demo Play mode.

4.

Adjust the volume.

Move the [VOLUME] slider up while a demo song is playing to

raise the volume to a suitable level.

5.

Exit Demo Play mode.

If you select one of the two demo songs to listen to, the P-100

will exit the Demo Play mode automatically as soon as it

finishes the song. To exit Demo play mode while a song is

playing, the press the [-l] button.

Switching between modes

You will not be able to enter the Demo Play mode — or any of the other play modes. for that

matter — when the P-100 is in Utility mode. (The LED above the [MIDI] button will blink

when the P-100 is in Utility mode.) To exit Utility mode, simply press the [MIDI] button.

Also. you will not be able to play the P-100 or use any of the Utility mode functions while the demo songs are

playing. Be sure to press the [-l] button to leave the Demo Play mode when you are done listening to the demo

songs.

PLAYING THE P-100

Selecting a voice

Once you’ve set up the P-100 and adjusted the volume level, you’re ready to start making music. The standard mode

for playing the P-100 is known as Single mode. In this mode, as its name implies, the P-100 plays only a single voice.

Playing the P-100 in Single mode is thus much like playing a normal acoustic piano. The biggest difference between

the P-100 and an acoustic piano is the fact that the P-100 lets you choose between ten different voices.

NO.

VOICE

1

PIANO 1

2

PIANO 2

3

E.PIANO

1

4

E.PIANO

2

5

CLAVINOVA TONE

6

VIBES

7

STRINGS

DESCRIPTION

Acoustic grand piano

Bright rock piano

Traditional electric piano

DX electric piano

A blend of harp and strings

Vibraphone

Orchestral strings

SAMPLE TYPE

POLYPHONY

Stereo/Mono

16/32

Mono

32

Mono

32

Mono

32

Layered

16

Layered

16

Mono

32

8

ORGAN

Jazz organ

Mono

32

9

BASS 1

Acoustic wood bass

Mono

32

10 BASS 2

Electric bass

Mono

32

To play the P-100 in Single mode, you need only press the

[VOICE/UTILITY] button for the voice you wish to play. The

MIDI program change number assigned to the button you press

will appear briefly in the display, followed by the number of the

voice you’ve selected. (For details regarding the assignment of

program change numbers to the [VOICE/UTILITY] buttons, refer

to the explanation of the program change transmit table on pages

40 and 41.)

7

Voice polyphony

As the table above shows, the P-100 produces 32 notes of polyphonic sound for seven of its

voices. For convenience, we will refer to these voices as

32-note

voices.

The remaining three voices can produce only 16 simultaneous notes. The first voice, PIANO

1, is a stereo voice, created using stereo sampling techniques. If you wish, however, you can switch it to mono

(for 32 notes output) by pressing and holding the [PIANO l] button for a few moments. When you do so, the

following display will appear briefly:

This display indicates that PIANO 1 has been switched to mono mode. This voice will remain in mono mode

even if you select a different voice and come back to it (although the P32 display will not reappear). To switch it

back to stereo mode, press and hold the [PIANO l] button again. The display below will appear briefly.

The voice is also switched to stereo mode automatically each time you turn on the power to the P- 100.

The other two voices, CLAVINOVA TONE and VIBES, are actually layered sounds which combine two

different tones in a single voice. They can produce a maximum of 16 simultaneous notes, and so are known

(together with the PIANO 1 voice in stereo mode) as

16-note

voices.

8

Using the reverb effect

Reverb adds warmth to sounds by creating the impression of an acoustic environment. The P-100 lets you select one of

three different types of reverb to apply to each voice. The ROOM setting simulates the reverberation characteristics of

a normal-sized room. STAGE reproduces the reverberations you would hear during a live on-stage performance.

HALL gives a sense of a room with more space between the walls. Finally, the OFF setting — a fourth option which

does not appear as a label on the upper panel — lets you play voices without any reverb.

To change the reverb setting, simply press the [REVERB] button

repeatedly. The P-100 will cycle through the possibilities, the LED

next to the name of each reverb type lighting in turn to indicate

your selection. (None of the LEDs will light when the OFF setting

is selected.)

The P-100 also lets you set the

depth

or level of the reverb effect

for each voice. The depth value appears in the display each time

you select a different reverb type. To change the depth setting,

move the [DATA ENTRY] slider while holding down the

[REVERB] button.

You can set the reverb depth to a level between 0 and 7. Setting the

depth to 0 will effectively turn the reverb off, while a value of 7

will produce the most noticeable reverb.

The P-100 will remember your reverb type and depth settings individually for each of the ten voices. If, for example,

you set the HALL effect at depth 6 for the PIANO 1 voice, then try playing the vibes using ROOM reverb at depth 4,

the P-100 will automatically switch back to HALL depth 6 when you next select PIANO 1.

When you play two voices in Dual or Split modes, the P-100 will apply the main voice reverb type and depth settings

to both voices, ignoring any settings which you may have made for the sub voice.

9

Using the modulation effects

In addition to the reverb effect, the P-100 lets you apply one of three different modulation effects to its voices.

CHORUS is a modulated delay effect that adds thickness to a voice, making it sound as though more than one

instrument is being played. The SYMPHONIC effect is a heavier chorus. TREMOLO applies a tremolo effect to

voices by modulating their output level. Finally, an OFF setting allows you to play without modulation.

These modulation effects have nothing to do with the vibrato effect which you can apply to voices using the

[MODULATION] wheel. The procedure for turning this vibrato effect on and off is described on page 38.

To change the current modulation effect setting, simply press the

[MODULATION] button repeatedly. The LED next to the name of

each modulation effect type will light in turn to indicate your

selection. (None of the LEDs will light when the OFF setting is

selected.)

The P-100 also lets you set the depth of the modulation effect.

The depth value appears in the display each time you select a

different effect type. To do so, move the [DATA ENTRY] slider

while holding down the [MODULATION] button.

You can set the modulation depth to a level between 0 and 7.

Setting the depth to 0 will reduce the modulation depth to a mini-

mum, whereas a value of 7 will result in the heaviest modulation.

The P-100 will remember modulation type and depth settings for each of the ten voices. When you play two voices in

Dual or Split modes, the P-100 will apply the main voice modulation settings to both voices. ignoring any settings you

have made for the sub voice.

10

Adjusting the equalization

The P-100’s equalizer works much like the three-band graphic equalizers found on many portable stereo sets. It allows

you to adjust the P-100’s output in three frequency ranges, LOW, MIDDLE and HIGH.

Slide the slider for each range up to increase the level of output, or

down to decrease output in that range. The graph below should

give you an idea how you can use the equalizer to modify the

sound output by the P-100.

11

Страница загружается ...

Yamaha Clavinova PF P-100 Руководство пользователя

Это руководство также подходит для

Yamaha Clavinova PF P-100 Руководство пользователя

Похожие модели бренда