Yamaha YDP-101 Руководство пользователя

Бренд: Yamaha

Модель: YDP-101

Категория: Музыкальные инструменты

Тип: Руководство пользователя

IMPORTANT

Check your power supply

Make sure that your local AC

mains voltage matches the volt-

age specified on the name plate

on the bottom panel. In some ar-

eas a voltage selector may be

provided on the bottom panel of

the main keyboard unit near the

power cord. Make sure that the

voltage selector is set for the volt-

age in your area. The voltage se-

lector is set at 240V when the unit

is initially shipped. To change the

setting use a “minus” screwdriver

to rotate the selector dial so that

the correct voltage appears next

to the pointer on the panel.

WICHTIG

Überprüfung der Stromversorgung

Vergewissern Sie sich vor dem An-

schließen an das Stromnetz, daß die

örtliche Netzspannung den

Betriebsspannungswerten auf dem

Typenschild an der Unterseite des In-

struments entspricht. In bestimmten

Verkaufsgebieten ist das Instrument

mit einem Spannungswähler an der

Unterseite neben der Netzkabel-

durchführung ausgestattet. Falls vor-

handen, muß der Spannungswähler

auf die örtliche Netzspannung einge-

stellt werden. Der Spannungswähler

wurde werkseitig auf 240 V voreinge-

stellt. Zum Verstellen drehen Sie den

Spannungsregler mit einem Schlitz-

schraubendreher, bis der Zeiger auf

den korrekten Spannungswert weist.

IMPORTANT

Contrôler la source d’alimentation

Vérifiez que la tension spécifiée sur

le panneau inférieur correspond à

la tension du secteur. Dans certai-

nes régions, l’instrument peut être

équipé d’un sélecteur de tension si-

tué sur le panneau inférieur du cla-

vier à proximité du cordon d’alimen-

tation. Vérifiez que ce sélecteur est

bien réglé en fonction de la tension

secteur de votre région. Le sélec-

teur de tension est réglé sur 240 V

au départ d’usine. Pour modifier ce

réglage, utilisez un tournevis à

lame plate pour tourner le sélecteur

afin de mettre l’indication corres-

pondant à la tension de votre ré-

gion vis à vis du repère triangulaire

situé sur le panneau.

IMPORTANTE

Verifique la alimentación de

corriente

Asegúrese de que tensión de ali-

mentación de CA de su área corres-

ponde con la tensión especificada en

la placa de características del panel

inferior. En algunas zonas puede

haberse incorporado un selector de

tensión en el panel inferior de la

unidad del teclado principal, cerca del

cable de alimentación. Asegúrese de

que el selector de tensión esté

ajustado a la tensión de su área. El

selector de tensión se ajusta a 240V

cuando la unidad sale de fábrica. Para

cambiar el ajuste, emplee un destorni-

llador de cabeza “recta” para girar el

selector de modo que aparezca la

tensión correcta al lado del indicador

del panel.

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

IMPORTANT. The wires in this mains lead are coloured in accor-

dance with the following code:

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured makings identifying the terminals

in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the termi-

nal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth terminal of

the three pin plug.

(2 wires)

The serial number of this product may be found on the bottom of the

unit. You should note this serial number in the space provided below

and retain this manual as a permanent record of your purchase to aid

identification in the event of theft.

Model No.

Serial No.

(bottom)

YDP-101

• Never insert or drop paper or metallic or other objects between the slits of

the key cover and the keyboard. If this happens, immediately turn off the

power and remove the electric plug from the outlet and have the instrument

inspected by qualified Yamaha service personnel.

• Do not place the instrument against a wall (allow at least 3 cm/one-inch

from the wall), since this can cause inadequate air circulation, and possibly

result in the instrument overheating.

• Read carefully the attached documentation explaining the assembly pro-

cess. Failure to assemble the instrument in the proper sequence might re-

sult in damage to the instrument or even injury.

• Do not operate the instrument for a long period of time at a high or uncom-

fortable volume level, since this can cause permanent hearing loss. If you

experience any hearing loss or ringing in the ears, consult a physician.

■USING THE BENCH

• Do not play carelessly with or stand on the bench. Using it as a tool or step-

ladder or for any other purpose might result in accident or injury.

• Only one person should sit on the bench at a time, in order to prevent the

possibility of accident or injury.

• If the bench screws become loose due to extensive long-term use, tighten

them periodically using the included tool.

■SAVING USER DATA

• Save all data to an external device such as the Yamaha MIDI Data Filer MDF3,

in order to help prevent the loss of important data due to a malfunction or

user operating error.

Yamaha cannot be held responsible for damage caused by improper use or modi-

fications to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep these precautions in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,

short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Do not open the instrument or attempt to disassemble the internal parts or

modify them in any way. The instrument contains no user-serviceable parts.

If it should appear to be malfunctioning, discontinue use immediately and

have it inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill

into any openings.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the instrument, or if any unusual smells or

smoke should appear to be caused by it, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the instrument

inspected by qualified Yamaha service personnel.

• Only use the voltage specified as correct for the instrument. The required

voltage is printed on the name plate of the instrument.

• Before cleaning the instrument, always remove the electric plug from the

outlet. Never insert or remove an electric plug with wet hands.

• Check the electric plug periodically and remove any dirt or dust which may

have accumulated on it.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the

instrument or other property. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy

objects on it, or place it in a position where anyone could walk on, trip over,

or roll anything over it.

• When removing the electric plug from the instrument or an outlet, always

hold the plug itself and not the cord. Pulling by the cord can damage it.

• Do not connect the instrument to an electrical outlet using a multiple-con-

nector. Doing so can result in lower sound quality, or possibly cause over-

heating in the outlet.

• Remove the electric plug from the outlet when the instrument is not to be

used for extended periods of time, or during electrical storms.

• Before connecting the instrument to other electronic components, turn off

the power for all components. Before turning the power on or off for all

components, set all volume levels to minimum.

• Do not expose the instrument to excessive dust or vibrations, or extreme

cold or heat (such as in direct sunlight, near a heater, or in a car during the

day) to prevent the possibility of panel disfiguration or damage to the inter-

nal components.

• Do not use the instrument near other electrical products such as televisions,

radios, or speakers, since this might cause interference which can affect

proper operation of the other products.

• Do not place the instrument in an unstable position where it might acciden-

tally fall over.

• Before moving the instrument, remove all connected cables.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-impregnated wiping cloths. Also, do

not place vinyl, plastic or rubber objects on the instrument, since this might

discolor the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the instrument, and do

not use excessive force on the buttons, switches or connectors.

• Take care that the key cover does not pinch your fingers, and do not insert a

finger or hand in the key cover gap.

(1)B_EL/CL-3vari.

* The illustrations and LCD screens as shown in this owner’s manual are for instruc-

tional purposes only, and may be different from the ones on your instrument.

YDP-101

Introduction

Thank you for choosing a Yamaha YDP-101 Digital Piano. Your YDP-101 is a fine musical instrument

that employs advanced Yamaha music technology. With the proper care, your YDP-101 will give you many

years of musical pleasure.

● Stereo sampling of the acoustic piano voices offers unmatched realism and expressive

power, while the AWM (Advanced Wave Memory) tone generator system offers rich,

realistic reproductions of all other voices.

● Piano-like touch response — adjustable in 4 stages — provides extensive expressive

control and outstanding playability.

● Dual mode allows 2 voices to be played simultaneously.

● Metronome feature with variable tempo facilitates practice.

● 2-track digital recorder lets you record and play back anything you play on the key-

board.

● MIDI compatibility and a range of MIDI functions make the YDP-101 useful in a range

of advanced MIDI music systems.

Included Accessories

● Owner’s Manual

● Bench

● Stereo Headphones

In order to make the most of your YDP-101’s performance potential and features, we urge you to read

this Owner’s Manual thoroughly, and keep it in a safe place for later reference.

YDP-101

Contents

The Control Panel .......................................................... 6

Key Cover & Music Stand .............................................. 8

Connections ................................................................... 9

Selecting & Playing Voices .......................................... 10

Playing the Demonstration Tunes ................................ 11

■

Voice Demo .............................................................. 11

■

Piano Song .............................................................. 12

■

Piano Song A-B Repeat .......................................... 13

■

Piano Song Part Cancel ......................................... 14

●

Synchro Start ..................................................... 14

●

Left Pedal Start/Stop ......................................... 14

The Dual Mode ............................................................ 15

●

Other Dual Mode Functions ............................... 15

Reverb ........................................................................ 16

●

Adjusting Reverb Depth ..................................... 16

The Pedals................................................................... 17

●

Damper (Right) Pedal ........................................ 17

●

Sostenuto (Center) Pedal .................................. 17

●

Soft (Left) Pedal ................................................. 17

Touch Sensitivity ......................................................... 18

Transposition ............................................................... 18

Tuning ......................................................................... 19

●

Tuning Up ........................................................... 19

●

Tuning Down ...................................................... 19

●

To Restore Standard Pitch ................................. 19

The Metronome & Tempo Control ................................ 20

■

The Metronome ........................................................ 20

●

Metronome Time Signature ............................... 20

●

Metronome Volume Function ............................. 20

■

Tempo Control ......................................................... 20

Using the Recorder ...................................................... 21

■

Recording ................................................................ 21

●

Changing the Initial Settings .............................. 22

●

Erasing a Single Track ....................................... 22

■

Playback................................................................... 23

●

Synchro Start ..................................................... 23

●

Left Pedal Start/Stop ......................................... 23

The Function Mode ...................................................... 24

●

To Select a Function … ...................................... 24

■

F1: Tuning ................................................................ 25

■

F2: Scale .................................................................. 25

F2.1: Scale ........................................................... 25

F2.2: Base Note ................................................... 25

■

F3: Dual Mode Functions ....................................... 26

F3.1: Dual Balance ............................................... 26

F3.2: Dual Detune ................................................ 26

F3.3: 1st Voice Octave Shift ................................. 26

F3.4: 2nd Voice Octave Shift ................................ 26

F3.5: Reset ........................................................... 26

■

F4: Left Pedal Mode ................................................ 27

■

F5: Metronome Volume ........................................... 27

■

F6: Piano Song Part Cancel Volume ...................... 27

■

F7: MIDI Functions .................................................. 28

●

A Brief Introduction to MIDI ............................... 28

F7.1: MIDI Transmit Channel Selection ................ 28

F7.2: MIDI Receive Channel Selection ................ 28

F7.3: Local Control ON/OFF ................................ 29

F7.4: Program Change ON/OFF .......................... 29

F7.5: Control Change ON/OFF ............................ 30

F7.6: MIDI Transmit Transpose ............................. 30

F7.7: Panel/Status Transmit .................................. 30

F7.8: Bulk Data Dump .......................................... 30

■

F8: Backup Functions............................................. 31

F8.1: Voice ............................................................ 31

F8.2: MIDI ............................................................. 31

F8.3: Tuning .......................................................... 31

F8.4: Pedal ........................................................... 31

Factory Preset Recall .................................................. 32

Troubleshooting ........................................................... 32

Options & Expander Modules ...................................... 32

Demo and Piano Song List................................................ 33

Factory Setting List............................................................ 34

MIDI Data Format................................................................ 35

MIDI Implementation Chart ............................................... 39

Keyboard Stand Assembly ................................................ 40

Specifications ..................................................................... 46

YDP-101

B0A0G0F0E0D0C0B-1A-1

C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5

MASTER VOLUME

MAXMIN

ROOM

HALL 1

HALL 2

STAGE

HARD

MEDIUM

SOFT

FUNCTION

TRACKSTART/

STOP REC

SONG

SELECT

–

YES

SONGFUNCTIONTEMPO

METRO-

NOME

VARIATION

PIPE

ORGAN

STRINGS

HARPSI-

CHORD

E. PIANO

GRAND

PIANO

TOUCHREVERBTRANSPOSEDEMO

MASTER VOLUME

MAX

MIN

DEMO

TRANSPOSE

REVERB

ROOM

HALL1

HALL2

STAGE

TOUCH

HARD

MEDIUM

SOFT

GRAND

PIANO

E.PIANO

HARPSI-

CHORD

STRINGS

PIPE

ORGAN

VARIATION

234 56 7

The Control Panel

1 [POWER] Switch

Press the [POWER] switch once to turn the

power ON, a second time to turn the power OFF.

When the power is initially turned ON, a voice

selector LED will light, and the power indicator

located below the left end of the keyboard will light.

2 [MASTER VOLUME] Control

The [MASTER VOLUME] control adjusts the

volume (level) of sound produced by the YDP-101’s

internal stereo sound system. The [MASTER

VOLUME] control also adjusts headphone volume

when a pair of headphones is plugged into the

PHONES jack (page 9).

3 [DEMO] Button

Activates the demo playback mode in which you

can select playback of different demonstration

sequences for each of the YDP-101’s voices. See

page 11 for details.

4 [TRANSPOSE] Button

The [TRANSPOSE] button allows access to the

YDP-101’s TRANSPOSE function (to shift the pitch

of the entire keyboard up or down in semitone

intervals).

5 [REVERB] Button

The [REVERB] button selects a number of

digital reverb effects that you can use for extra depth

and expressive power. See page 16 for details.

6 [TOUCH] Button

The [TOUCH] button makes it easy to adjust the

touch response of the YDP-101 to match your

playing style. See page 18 for details.

7 Voice Selectors & [VARIATION] Button

Simply press any of the voice selectors to select

the corresponding voice. The voice selector LED

will light to indicate which voice is currently se-

lected. Press the [VARIATION] button so that its

indicator lights to select a variation of the currently

selected voice.

PHONES Jacks (Bottom panel) (See page 9)

Tuning keys (See page 19)

YDP-101

The Control Panel

There is also a dual mode in which two voices

can be played simultaneously across the full range of

the keyboard (see page 15 for details).

8 [METRONOME] Button

Turns the metronome sound on and off. The

[TEMPO ▼/▲] buttons, below, are used to set the

tempo of the metronome sound. The [–/NO] and [+/

YES] buttons are used to change the time signature

(beat) of the metronome if used while the [METRO-

NOME] button is held — page 20.

9 [TEMPO ▼/▲] (FUNCTION </>) Buttons

These buttons adjust the tempo of the metronome

function as well as the playback tempo of the re-

corder function. The tempo range is from 32 to 280

beats per minute — page 20. These same buttons are

also used to select functions — page 24.

0 [FUNCTION] Button

This button accesses a range of utility functions

— including the MIDI functions — that significantly

enhance versatility and playability. See page 24 for

details.

! [SONG] Button

This button enters the Piano Song Mode. While

in this mode you can use the [SONG SELECT ▼/

▲] buttons to select from 50 songs.

@ [SONG SELECT ▼/▲] (–/NO, +/YES) Buttons

These buttons select a piano song number for

playback, and are also used to adjust a range of other

parameters (i.e. their “–/NO” and “+/YES” func-

tions).

# [START/STOP] and [REC] Buttons

These buttons control the YDP-101’s recorder,

letting you record and play back just about anything

you play on the keyboard.

$ TRACK [1] and [2] Buttons

The YDP-101 has a 2-track recorder, and these

buttons are used to select the track(s) to be recorded

or played back. See page 21 for details.

% Pedals

The soft (left), sostenuto (center) and damper

(right) pedals provide a range of expressive control

capabilities similar to the pedal functions on an

acoustic piano. The left pedal can also be assigned to

the song start/stop operation. See page 17 for de-

tails.

Soft pedal

Damper pedal

Sostenuto pedal

F5 G5 A5 B5 C6

D6 E6 F6 G6 A6 B6 C7

POWER

DIGITAL PIANO YDP-101

METRO-

NOME

FUNCTION

TRACK

START

STOP

REC

SONG

SELECT

–

YES

TEMPO

FUNCTION

890 !@ # $

YDP-101

To open the key cover:

ZLift the cover slightly (not too much).

XSlide the cover open.

• Hold the cover with both hands when moving it, and do not release it until

it is fully opened or closed. Be careful to avoid catching fingers (yours or

others) between the cover and main unit.

• Do not place objects on top of the key cover. Small objects placed on the

key cover may fall inside the main unit when the cover is opened and may

not be able to be removed. This could cause electric shock, short circuit,

fire or other serious damage to the instrument.

To close the key cover:

ZSlide the cover toward you.

XGently lower the cover over the keys.

Be careful to avoid catching your

fingers when opening or closing

the cover.

Key Cover & Music Stand

To raise the music stand:

ZPull the stand up and toward yourself as far as it will go.

XFlip down the two metal supports at the left and the right on the rear of

the music stand.

CLower the music stand so that it rests on the metal supports.

To lower the music stand:

ZPull the music stand toward yourself as far as it will go.

XRaise the two metal supports (at the rear of the stand).

CGently lower the music stand backward until it is all the way down.

• Do not try to use the music stand in a half-raised position.

When lowering the stand, do not release your hands from the music stand

until it is all the way down.

Key Cover

Music Stand

YDP-101

Connections

1 AUX OUT L/L+R and R Jacks

The AUX OUT L/L+R and R jacks deliver the output of the YDP-101

for connection to an instrument amplifier, mixing console, PA system, or

recording equipment. If you will be connecting the YDP-101 to a monau-

ral sound system, use only the L/L+R jack. When a plug is inserted into

the L/L+R jack only, the left- and right-channel signals are combined and

delivered via the L/L+R jack so you don’t lose any of the YDP-101’s

sound.

• The AUX OUT jack signal is not controlled by the YDP-101’s volume control.

Use the volume control on the external audio equipment to adjust the level.

2 PEDAL Jack

This terminal is for connecting the pedal cord from the pedal box (refer

to the “Keyboard Stand Assembly” on pages 40-45).

3 MIDI IN and OUT Connectors

The MIDI IN connector receives MIDI data from an external MIDI

device (such as a sequencer or MIDI instrument) which can be used to

control the YDP-101. The MIDI OUT connector transmits MIDI data

generated by the YDP-101 (e.g. note and velocity data produced by

playing the YDP-101 keyboard).

More details on MIDI are given in “MIDI Functions” on page 28.

● PHONES Jacks

(Bottom Panel)

Two sets of standard stereo headphones can be plugged in here for

private practice or late-night playing. The internal speaker system is

automatically shut off when a pair of headphones is plugged into either of

the PHONES jacks.

AUX OUT

L+R

Stereo System

123

MIDI

PEDAL

IN OUT

AUX OUT

L+R

Sequencer

MIDI

IN OUT

YDP-101

After making sure that the YDP-101’s AC cord is properly plugged

into the YDP-101 itself and plugged into a convenient AC wall outlet,

press the [POWER] switch located to the right of the keyboard to turn

the power ON. In some areas a plug adaptor may be provided to match

the pin configuration of the AC wall outlets in your area.

When the power is turned ON, one of the voice selector LEDs will

light, and the power indicator located below the left end of the keyboard

will light.

Set the Volume ..................................................................................................

Initially set the [MASTER VOLUME] control about half way

between the “MIN” and “MAX” settings. Then, when you start playing,

re-adjust the [MASTER VOLUME] control for the most comfortable

listening level.

Select a Voice .....................................................................................................

Select the desired voice by pressing one of the voice selectors. Use

the [VARIATION] button to select a variation of the current voice, as

required.

Play................................................................................................................................

The YDP-101 also offers keyboard touch response, so the volume

and timbre of notes played can be controlled according to how “hard”

you play the keys. The amount of variation available depends on the

selected voice.

Add Reverb As Required .......................................................................

You can add or change reverb as desired by using the [REVERB]

button (page 16).

Selecting & Playing Voices

Turn Power On...................................................................................................

MASTER VOLUME

MAX

MIN

POWER

GRAND

PIANO

E.PIANO

HARPSI-

CHORD

STRINGS

PIPE

ORGAN

VARIATION

REVERB

ROOM

HALL1

HALL2

STAGE

YDP-101

Demonstration tunes are provided that effectively demonstrate each of the

YDP-101’s voices. There are also 50 piano songs that you can play individually,

all in sequence, or in random order. Here’s how you can select and play the

demo tunes.

NOTE

• The demo or piano song mode cannot be engaged while the recorder (page 21) is in use.

• No MIDI reception occurs in the demo/piano song mode.

• The demo/piano song data is not transmitted via the MIDI connectors.

* See page 33 for a complete listing of the demo tunes and piano songs.

Playing the Demonstration Tunes

Engage the Demo Mode .........................................................................

Play a Voice Demo.........................................................................................

Press one of the voice selectors to start playback of all songs starting

from the corresponding voice demo tune — featuring the voice nor-

mally selected by that voice selector button. (If you press the [START/

STOP] button instead of a voice selector button, the GRAND PIANO

demo tune will begin playback.) The indicator of the selected voice

selector button will flash during playback, and “- - -” will appear on the

LED display. You can start playback of any other voice demo tune

during playback by simply pressing the corresponding voice selector.

You can stop playback at any time by pressing the [START/STOP]

button or the voice selector of the currently playing demo.

NOTE

• Use the [MASTER VOLUME] control to adjust the volume.

Press the [DEMO] button to engage the demo mode — the voice

selector indicators will flash in sequence.

Voice Demo

Exit From the Demo Mode....................................................................

Press the [DEMO] button to exit from the demo mode and return to

the normal play mode.

DEMO

GRAND

PIANO

E.PIANO

HARPSI-

CHORD

STRINGS

PIPE

ORGAN

YDP-101

Playing the Demonstration Tunes

Engage the Piano Song Mode .........................................................

Play a Piano Song .........................................................................................

To play any of the 50 piano songs provided, use the [SONG SE-

LECT ▼/▲] buttons to select the number of the tune you want to play

(the number will appear on the LED display), then press the [START/

STOP] button. Playback will stop automatically when playback of the

selected piano song has finished.

Select “ALL” instead of a number to play all piano songs in se-

quence, or select “rnd” to continuously play all piano songs in ran-

dom order. Press the [START/STOP] button to stop playback.

• Use the [MASTER VOLUME] control to adjust the volume.

• You can use the [TEMPO

▼

▲

] buttons to adjust the playback tempo as

required. This produces a relative tempo variation, with a range from “-50”

through “- - -” to “50” at maximum; the range will differ depending on the

selected song.

• The default tempo “- - -” is automatically selected whenever a new piano

song is selected, or playback of a new piano song begins during “

ALL

” or

“

rnd

” playback.

• You can play the keyboard along with the piano song playback. The voice

playing on the keyboard can be changed.

• You can change the Reverb type that is applied to the voice you play on

the keyboard and for the piano song playback. You can change the Touch

sensitivity that is applied to the voice you play on the keyboard. When a

new piano song is selected or a new piano song is automatically started

in continuous play, the HALL 1 reverb type will automatically be selected.

Press the [SONG] button to engage the piano song mode — the

[SONG], [1] and [2] indicators will light.

Piano Song

Exit From the Piano Song Mode....................................................

Press the [SONG] button to exit from the piano song mode, the

indicator will go off, and return to the normal play mode.

SONG

START

STOP

SONG

SELECT

–

YES

SONG

YDP-101

Piano Song A-B Repeat

The A-B Repeat function can be used to continuously repeat a

specified phrase within a piano song. Combined with the Part Cancel

function described below, this provides an excellent way to practice

difficult phrases.

Specify the Beginning (A) of the Phrase..............................

Select and play a piano song, then press the [FUNCTION] button at

the beginning of the phrase you want to repeat. This sets the “A” point

(“A-” will appear on the display).

To set the “A” point at the very beginning of the song, press the

[FUNCTION] button before starting playback.

Specify the End (B) of the Phrase ...............................................

Press the [FUNCTION] button a second time at the end of the

phrase. This sets the “B” point (“A-b” will appear on the display). At

this point repeat playback will begin between the specified A and B

points.

Stop Playback....................................................................................................

Press the [START/STOP] button to stop playback while retaining

the specified A and B points. A-B repeat playback will resume if the

[START/STOP] button is then pressed again.

To cancel the A and B points press the [FUNCTION] button once.

NOTE

• The A and B points are automatically canceled when a new song is

selected.

• The A-B Repeat function cannot be used during “

ALL

” or “

rnd

” playback.

FUNCTION

TRACK

START

STOP

REC

Playing the Demonstration Tunes

YDP-101

Piano Song Part Cancel

The 50 piano songs have separate left- and right-hand parts that can

be turned on and off as required so you can practice the corresponding

part on the keyboard. The right-hand part is played by the recorder’s [1]

track, and the left-hand part is played by recorder’s [2] track. (Some of

the songs are arrangements for four-hands, tracks [1] and [2] corre-

spond to primo and secondo parts of the arrangement.)

Turn the Desired Part Off.......................................................................

Press the TRACK [1] or [2] button to turn the corresponding part off

— the corresponding indicator will go out (these buttons alternately

toggle the corresponding part on and off).

NOTE

• The parts can be turned on or off even during playback.

• The Piano Song Part Cancel function cannot be used during “

ALL

” or

“

rnd

” playback.

• The “Piano Song Part Cancel Volume” function described on page 27 can

be used to set the canceled part so that it plays at a volume from “0” (no

sound) to “20”. The default setting is “5”.

• Both parts are automatically turned ON whenever a new song is selected.

Start/Stop Playback.....................................................................................

Press the [START/STOP] button to start and stop playback as

required.

Synchro Start .....................................................................................................

When the Synchro Start function is engaged, playback of the se-

lected piano song will begin automatically as soon as you start playing

on the keyboard.

To engage the Synchro Start function press the [START/STOP]

button while holding the part button corresponding to the part which is

ON. A dot will appear in the lower right corner of the display. (Repeat

the previous operation to disengage the Syncro Start function.)

Playback will then start as soon as you begin playing on the key-

board.

NOTE

• If you hold a track button which is OFF while pressing the [START/STOP]

button, that track will be turned ON and the Synchro Start mode will be

engaged.

Left Pedal Start/Stop ..................................................................................

The left pedal can be assigned to start and stop piano song playback

via the “Left Pedal Mode” function described on page 27.

Playing the Demonstration Tunes

TRACK

START

STOP

REC

TRACK

START

STOP

REC

TRACK

START

STOP

REC

YDP-101

The Dual Mode

The dual mode makes it possible to play two voices simultaneously across

the entire range of the keyboard.

To activate the dual mode simply press two voice selectors at the

same time (or press one voice selector while holding another). The

voice indicators of both selected voices will light when the dual mode is

active. To return to the normal single-voice play mode, press any single

voice selector.

According to the voice numbering priority as shown in the diagram

on the left, lower valued voice numbers will be designated as the 1st

Voice (the other voice will be designated as the 2nd Voice).

The [STRINGS] [VARIATION] voice has a slow attack. This

voice can sometimes be used with another voice in the Dual Mode to

produce a better “blend”.

NOTE

• The [VARIATION] button indicator will light if the variation is engaged for

either or both of the dual-mode voices. While the dual mode is engaged

the [VARIATION] button can be used to turn the variation for both voices

on or off. To use the variation for only one of the voices the setting must

be made prior to engaging the dual mode.

• [REVERB] in the Dual Mode

The reverb type assigned to the 1st Voice will take priority over the other.

(If the reverb is set to OFF, the 2nd Voice’s reverb type will be in affect.)

Reverb depth setting via the panel controls (i.e. pressing the [-/NO] or [+/

YES] buttons while holding the [REVERB] button — see page 16) will be

applied to the 1st Voice only.

Other Dual Mode Functions ...............................................................

The YDP-101 Function mode provides access to a number of other

dual-mode functions, listed below. See the corresponding pages for

details.

• Dual Balance ................................................. 26

• Dual Detune .................................................. 26

• 1st Voice Octave Shift ................................... 26

• 2nd Voice Octave Shift .................................. 26

• Reset ............................................................. 26

Voice numbering priority

1 2 3 4 5

GRAND

PIANO

E.PIANO

HARPSI-

CHORD

STRINGS

PIPE

ORGAN

IANO

HARPSI-

CHORD

STRINGS

PIP

ORG

YDP-101

Reverb

The [REVERB] button selects a number of digital reverb effects that you can

use for extra depth and expressive power.

To select a reverb type press the [REVERB] button a few times until

the indicator corresponding to the desired type lights (the indicators

light in sequence each time the [REVERB] button is pressed). No

reverb is produced when all indicators are off.

OFF

No reverb effect is selected when no REVERB indicator is lit.

ROOM

This setting add a continuous reverb effect to the sound that is similar

to the type of acoustic reverberation you would hear in a room.

HALL 1

For a “bigger” reverb sound, use the HALL 1 setting. This effect

simulates the natural reverberation of a small-size concert hall.

HALL 2

For a really spacious reverb sound, use the HALL 2 setting. This effect

simulates the natural reverberation of a large concert hall.

STAGE

A simulation of the type of reverb produced in a stage environment.

NOTE

• The default reverb type (including OFF) and depth settings are different

for each voice.

Adjusting Reverb Depth .........................................................................

Adjust the reverb depth for the selected voice by using the [–/NO]

and [+/YES] buttons while holding the [REVERB] button. The depth

range is from 0 through 20 (the current depth setting appears on the

LED display while the [REVERB] button is held). A setting of “0”

produces no effect, while a setting of “20” produces maximum reverb

depth. Press the [–/NO] and [+/YES] buttons simultaneously while

holding the [REVERB] button to recall the default setting for the

current voice (default depth settings are different for each voice).

REVERB

ROOM

HALL1

HALL2

STAGE

REVERB

ROOM

HALL1

HALL2

STAGE

SONG

SELECT

–

YES

YDP-101

The Pedals

Soft (Left) Pedal ...............................................................................................

The soft pedal reduces the volume and slightly changes the timbre of

notes played while the pedal is pressed. The soft pedal will not affect

notes which are already playing when it is pressed.

The left pedal can also be assigned to the song start/stop operation

via the “Left Pedal Mode” described on page 27.

The YDP-101 has three foot pedals that produce a range of expressive

effects similar to those produced by the pedals on an acoustic piano.

Soft pedal

Damper pedal

Sostenuto pedal

Sostenuto (Center) Pedal ......................................................................

If you play a note or chord on the keyboard and press the sostenuto

pedal while the note(s) are held, those notes will be sustained as long as

the pedal is held (as if the damper pedal had been pressed) but all

subsequently played notes will not be sustained. This makes it possible

to sustain a chord, for example, while other notes are played “staccato.”

NOTE

• Organ and string voices will continue to sound for as long as the soste-

nuto pedal is depressed.

Damper (Right) Pedal ................................................................................

The damper pedal functions in the same way as a damper pedal on

an acoustic piano. When the damper pedal is pressed notes played have

a long sustain. Releasing the pedal immediately stops (damps) any

sustained notes.

YDP-101

Touch Sensitivity

Four different types of keyboard touch sensitivity — HARD, MEDIUM, SOFT

or FIXED — can be selected to match different playing styles and preferences.

To select a touch sensitivity type press the [TOUCH] button a few

times until the indicator corresponding to the desired type lights (the

indicators light in sequence each time the [TOUCH] button is pressed).

HARD

The HARD setting requires the keys to be played quite hard to

produce maximum loudness.

MEDIUM

The MEDIUM setting produces a fairly “standard” keyboard response.

This is the initial factory default setting.

SOFT

The SOFT setting allows maximum loudness to be produced with

relatively light key pressure.

FIXED (no indicator lit)

All notes are produced at the same volume no matter how hard the

keyboard is played.

When the FIXED type is selected, the volume of notes played in the

FIXED mode can be set by using the [–/NO] and [+/YES] buttons while

the [TOUCH] button is held (the current volume level appears on the

display). The volume range is from 1 through 127. The default setting

is 64.

NOTE

• This setting does not change the weight of the keyboard.

• The touch sensitivity type and volume set in the FIXED mode will become

the common setting for all voices.

Transposition

Use the [–/NO] or [+/YES] button while holding the [TRANS-

POSE] button to transpose down or up as required. The transposition

range is from “–12” (down one octave) through “0” (normal pitch) to

“12” (up one octave). The amount of transposition appears on the LED

display while the [TRANSPOSE] button is held. The default transpose

setting is “0”.

NOTE

• The [TRANSPOSE] button indicator remains lit when a transpose setting

other than “0” is selected.

• Notes below and above the A-1 … C7 range of the YDP-101 sound one

octave higher and lower, respectively.

The YDP-101’s TRANSPOSE function makes it possible to shift the pitch of

the entire keyboard up or down in semitone intervals up to a maximum of 12

semitones (i.e. a maximum of one octave up or down). “Transposing” the pitch of

the YDP-101 keyboard facilitates playing in difficult key signatures, and you can

easily match the pitch of the keyboard to the range of a singer or other instru-

mentalist.

TOUCH

HARD

MEDIUM

SOFT

TRANSPOSE

SONG

SELECT

–

YES

YDP-101

Tuning

Tuning makes it possible to adjust the pitch of the YDP-101 over a 427.0 Hz

… 453.0 Hz (corresponding to the A3 note’s Hz) range in approximately 0.2

Hertz intervals. Pitch control is useful for tuning the YDP-101 to match other

instruments or recorded music.

Tuning Up ...............................................................................................................

Z To tune up (raise pitch), hold the A-1 and B-1 keys simultaneously.

X Press any key between C3 and B3. Each time a key in this range is

pressed the pitch is increased by approximately 0.2 Hz.

The [–/NO] and [+/YES] buttons can also be used to tune down or up,

respectively, in

approximately

1 Hz

decrements/

increments. Press the

[–/NO] and [+/YES] buttons simultaneously to recall standard tuning

(A3 = 440 Hz).

C Release the A-1 and B-1 keys.

Tuning Down .......................................................................................................

Z To tune down (lower pitch), hold the A-1 and A#-1 keys simulta-

neously.

X Press any key between C3 and B3. Each time a key in this range is

pressed the pitch is decreased by approximately 0.2 Hz.

The [–/NO] and [+/YES] buttons can also be used to tune down or up,

respectively, in

approximately

1 Hz

decrements/

increments. Press the

[–/NO] and [+/YES] buttons simultaneously to recall standard tuning

(A3 = 440 Hz).

C Release the A-1 and A#-1 keys.

To Restore Standard Pitch...................................................................

Z To restore the default pitch (A3 = 440 Hz), hold the A-1, A#-1 and

B-1 keys simultaneously.

X Press any key between C3 and B3.

C Release the A-1, A#-1 and B-1 keys.

In terms of “Hertz”, the overall tuning range is from 427.0 Hz to 453.0

Hz. The current tuning setting is shown on the LED display while the tuning

is being adjusted. Tenths of a Hertz are indicated on the LED display by the

appearance and position of one or two dots, as in the following example:

NOTE

• An alternative tuning method is available in the Function mode — page 25.

Display Value

440 440.0

4.40 440.2

44.0 440.4

440. 440.6

4.40. 440.8

-1

SONG

SELECT

–

YES

SONG

SELECT

–

YES

-1

YDP-101

The Metronome & Tempo Control

The YDP-101 built-in metronome is a convenient feature for practice, and it

can also provide a solid rhythmic guide when recording using the Recorder

feature, described in the next section.

The Metronome

The metronome sound is alternately turned on and off by pressing

the [METRONOME] button. When on, the beat indicator flashes at the

current tempo.

Metronome Time Signature.................................................................

The time signature (beat) of the metronome can be set by using the

[–/NO] and [+/YES] buttons while holding the [METRONOME]

button. You can set the beat to 0, 2, 3, 4 or 6 (the current setting appears

on the LED display while the [METRONOME] button is held). Press

the [–/NO] and [+/YES] buttons simultaneously while holding the

[METRONOME] button to recall the default setting “0” (no accent).

Metronome Volume Function ............................................................

The volume of the metronome sound can be adjusted via the Metro-

nome Volume function in the Function mode—page 27.

Tempo Control

The tempo of the metronome and recorder playback (the recorder is

described in the next section) can be set from 32 to 280 beats per

minute by using the [TEMPO t/s] buttons. The selected tempo will

appear on the LED display while in the normal play mode and while the

[TEMPO t/s] buttons are being used to adjust the tempo in the

recording/playback mode. The default tempo (120 or the recorded song

tempo when the recorder contains data and the playback track indicator

is lit) can be recalled by simultaneously pressing the [t] and [s]

buttons.

Beat indicator

METRO-

NOME

TEMPO

FUNCTION

SONG

SELECT

–

YES

METRO-

NOME

Страница загружается ...

Yamaha YDP-101 Руководство пользователя

Бренд: Yamaha

Модель: YDP-101

Категория: Музыкальные инструменты

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha YDP-101 User manual
français: Yamaha YDP-101 Manuel utilisateur
italiano: Yamaha YDP-101 Manuale utente
español: Yamaha YDP-101 Manual de usuario
Deutsch: Yamaha YDP-101 Benutzerhandbuch
Nederlands: Yamaha YDP-101 Handleiding
português: Yamaha YDP-101 Manual do usuário
dansk: Yamaha YDP-101 Brugermanual
polski: Yamaha YDP-101 Instrukcja obsługi
čeština: Yamaha YDP-101 Uživatelský manuál
svenska: Yamaha YDP-101 Användarmanual
Türkçe: Yamaha YDP-101 Kullanım kılavuzu
suomi: Yamaha YDP-101 Ohjekirja
română: Yamaha YDP-101 Manual de utilizare

Yamaha YDP-101 Руководство пользователя

Yamaha YDP-101 Руководство пользователя

на других языках

Похожие модели бренда