Panasonic ES-LS6A Rechargeable Shaver Руководство пользователя

Operating Instructions

(Household use) Rechargeable Shaver

Model No. ES‑LS6A

English �� 3

Русский �� 21

Українська �� 41

Қазақша �� 61

2

3

English

Thank you for purchasing this Panasonic product.

Before operating this unit, please read these instructions completely and save them for future use�

Operating Instructions

(Household use) Rechargeable Shaver

Model No. ES‑LS6A

Safety precautions..................... 4

Important information ��8

Parts identication ��10

Preparation��10

How to use �� 11

Cleaning the shaver ��14

Replacing the system outer foil ��15

FAQ ��16

Troubleshooting ��16

Battery life ��19

Removing the built-in rechargeable

battery��19

Specications ��20

Contents

4

English

Safety precautions

Make sure to follow these instructions.

To prevent accidents, injuries or damage to property,

please follow the instructions below.

■The following chart indicates the degree of

damage caused by improper operation�

DANGER

Indicates a potential hazard that

will result in serious injury or death.

WARNING

Indicates a potential hazard that

could result in serious injury or

death.

CAUTION

Indicates a potential hazard that

could result in minor injury or

property damage.

■ The symbols are classied and explained as

follows�

This symbol indicates prohibition.

This symbol indicates requirement that must be

followed.

WARNING

►This product

This product has a built-in rechargeable

battery. Do not throw into re, apply heat, or

charge, use, or leave in a high temperature

environment�

‑ Doing so may cause overheating, ignition, or

explosion.

Do not modify or repair�

‑ Doing so may cause re, electric shock, or

injury.

Contact an authorized service centre for repair

(replacement of battery etc).

Never disassemble except when disposing of

the product�

‑

Doing so may cause re, electric shock, or injury.

5

English

WARNING

►In case of an abnormality or malfunction

Immediately stop using and remove the AC

adaptor if there is an abnormality or

malfunction�

‑ Failure to do so may cause re, electric shock,

or injury.

•The main unit, AC adaptor or cord is

deformed or abnormally hot�

•The main unit, adaptor or cord smells of

burning�

•There is an abnormal sound during use or

charging of the main unit�

‑ Immediately request inspection or repair at an

authorized service centre.

►Power supply

Do not connect or disconnect the adaptor to

a household outlet with a wet hand�

‑ Doing so may cause electric shock or injury.

Do not immerse the AC adaptor in water or

wash with water�

Do not place the AC adaptor over or near

water lled sink or bathtub.

Never use the appliance if the AC adaptor is

damaged or if the power plug ts loosely in a

household outlet�

Do not damage the cord or the power plug�

•Do not deface, modify, forcefully bend or

pull the cord or the power plug� Also, do

not place anything heavy on, twist or pinch

the cord�

‑ Doing so may cause electric shock or re due

to a short circuit.

Do not use in a way that would exceed the

rating of the household outlet or the wiring�

‑ Exceeding the rating by connecting too many

plugs to one household outlet may cause re

due to overheating.

Do not use anything other than the supplied

AC adaptor for any purpose�

Also, do not use any other product with the

supplied AC adaptor� (See page 10�)

‑ Doing so may cause burn or re due to a short

circuit.

Fully insert the power plug�

‑

Failure to do so may cause re or electric shock.

Disconnect the AC adaptor when cleaning the

main body with water�

‑

Failure to do so may cause electric shock or injury.

6

English

WARNING

Regularly clean the power plug and the

appliance plug to prevent dust from

accumulating�

‑ Failure to do so may cause re due to insulation

failure caused by humidity.

►Preventing accidents

Do not place within reach of children or

infants� Do not let them use it�

‑ Putting parts or accessories in the mouth may

cause an accident or injury.

If oil is consumed accidentally, do not induce

vomiting, drink a large amount of water and

contact a physician�

If oil comes into contact with eyes, wash

immediately and thoroughly with running

water and contact a physician�

‑ Failure to follow these instructions may result in

physical problems.

►Note the following precautions

This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance

by a person responsible for their safety�

Children should be supervised to ensure that

they do not play with the appliance�

‑ Failure to do so may cause an accident or

injury.

The supply cord cannot be replaced� If the

cord is damaged, the AC adaptor should be

scrapped�

‑ Failure to do so may cause an accident or

injury.

CAUTION

►Protecting the skin

Do not use excessive pressure to apply the

system outer foil to your lip or other part of

your face�

Do not apply the system outer foil directly to

blemishes or injured skin.

‑ Doing so may cause injury to skin.

7

English

CAUTION

Do not forcefully press the system outer foil�

Also, do not touch the system outer foil with

ngers or nails when in use.

Do not use this product for hair on head or

any other part of the body�

‑ Doing so may cause injury to skin or reduce the

life of the system outer foil.

Check the system outer foil for cracks or

deformations before use�

‑ Failure to do so may cause injury to the skin.

►Note the following precautions

Do not allow metal objects or trash to adhere

to the power plug or the appliance plug�

‑ Doing so may cause electric shock or re due

to a short circuit.

Do not share your shaver with your family or

other people�

‑ Doing so may result in infection or inammation.

Disconnect the adaptor from the household

outlet when not charging�

‑ Failure to do so may cause electric shock or re

due to electrical leakage resulting from

insulation deterioration.

Handling of the removed battery when

disposing

DANGER

•The rechargeable battery is exclusively for

use with this appliance� Do not use the

battery with other products�

•Do not charge the battery after it has been

removed from the product�

•Do not throw into re or apply heat.

•Do not hit, disassemble, modify, or puncture

with a nail�

•Do not let the positive and negative

terminals of the battery get in contact with

each other through metallic objects�

•Do not carry or store the battery together

with metallic jewellery such as necklaces

and hairpins�

•Do not use or leave the battery where it will

be exposed to high temperatures, such as

under direct sunlight or near other sources

of heat�

•Never peel off the tube�

‑ Doing so may cause overheating, ignition, or

explosion.

8

English

WARNING

After removing the rechargeable battery, do

not keep it within reach of children and infants.

‑

The battery will harm the body if accidentally

swallowed.

If this happens, consult a physician immediately.

If the battery uid leaks out and comes in

contact with the eyes, do not rub the eyes,

and thoroughly rinse with clean water, such

as tap water�

‑ Failure to do so may cause eye injury.

Consult a physician immediately.

CAUTION

If the battery uid leaks out and comes in

contact with the skin or clothes, rinse off with

clean water, such as tap water�

‑ Failure to do so may cause inammation.

Important information

• This WET/DRY shaver can be used for wet shaving

using shaving lather or for dry shaving. You can use

this watertight shaver in the shower and clean with

water. The following symbol means suitable for use in

a bath or shower.

• Treat yourself to wet lather shaves for at least three

weeks and notice the difference. Your Panasonic

WET/DRY shaver requires a little time to get used to

because your skin and beard need about a month to

adjust to any new shaving method.

• If you clean the shaver with water, do not use salt

water or hot water. Do not soak the shaver in water for

a long period of time.

• The following symbol indicates that a specic

detachable power supply unit is required for

connecting the electrical appliance to the supply

mains. The type reference of power supply unit is

marked near the symbol.

• Charge the appliance correctly according to these

Operating Instructions. (See page 10 “Charging the

shaver”.)

• This appliance contains battery that is only

replaceable by skilled persons. Please contact an

authorized service centre for the details of repair.

9

English

Note the following precautions

►When using

• Do not bring the system outer foil into contact with

hard objects.

Doing so may damage the system outer foil as it is

very thin and deforms easily.

• Do not drop or hit against other objects.

Doing so may cause injury.

►When storing

• Store the shaver in a place with low humidity after

use.

Failure to do so may cause malfunction due to

condensation or rust.

• Be sure to place the protective cap on the shaver

when carrying around or storing.

Failure to do so may cause injury to skin or reduce the

life of the system outer foil.

►When cleaning

• Do not dry the main unit with a dryer or a fan heater.

Doing so may cause malfunction or deformation of the

parts.

• Do not leave the shaver exposed to direct sunlight

with the foil frame detached.

Doing so may deteriorate the waterproof rubber and

degrade waterproof function, which may cause to

malfunction.

10

English

Parts identication



















a

b

c









Back













A Main body

1 Protective cap

2 System outer foil

3 Foil frame

4 Smooth rollers

• They help to glide

over the skin more

easily.

5 Foil frame release

buttons

6 Power switch

7 Lamp display

a. Battery capacity

lamp

b. Charge status

lamp ( )

c. Switch lock lamp

()

 Appliance socket

 Outer foil section

 System outer foil

release buttons

 Trimmer

 Trimmer handle

B AC adaptor (RE7-87)

 Adaptor

 Power plug

 Cord

 Appliance plug

Accessories

C Travel case

D Cleaning brush

E Oil

Preparation

Charging the shaver

• Turn the shaver off.

• Wipe off any water droplets on the appliance socket.

1 Insert the appliance plug

into the shaver�

2 Plug the adaptor into a

household outlet�

• Check that the charge status

lamp ( ) is glowing.

• Charging is completed after

approx. 1 hour.

3

Disconnect the adaptor

after charging is completed�

1

2

Note

You cannot operate the shaver while charging.

11

English

Quick charge

Even though the battery runs out, you can shave

once after 3‑minute charge.

(This will differ depending on usage.)

While charging After charging is

completed

glows.

The battery capacity

lamp will increase as

charging progresses.

All the battery capacity

lamp and will glow and

then turn off after

5 seconds.

Notes

• When charging the shaver for the rst time or when it

has not been in use for more than 6 months, the

charging time may change or the charge status lamp

() may not glow for a few minutes. It will eventually

glow if kept connected.

• Recommended ambient temperature for charging is

10 °C – 35 °C. It may take longer to charge, or the

charge status lamp ( ) will blink quickly and the

battery may fail to charge properly in extremely high

or low temperatures.

• The shaver can be used for approximately 2 weeks

with a full charge.

(Based on one 3‑minute dry‑shave usage per day in

an ambient temperature range of 20 °C – 30 °C.)

The number of usable days varies depending on the

following conditions.

‑ Beard thickness

‑ Pressure applied to the skin

‑

Usage frequency of the sonic vibration cleaning mode

• If there is noise from the radio or other sources while

using or charging the appliance, move to a different

location to use the appliance.

How to use

Shaving beard

1 Press and shave�

• The “shaving sensor”, which

automatically adjusts the power

depending on the beard thickness,

will operate.

It will shave with high power on areas

where the beard is heavy, and reduce

the power on areas where the beard

is thin, to reduce burden on the skin.

12

English

Tips for better shaving

Apply the whole system outer foil

perpendicularly against the skin

and shave by slowly gliding the

shaver over the face against the

grain of the beard.

• The beard under the chin and

around the throat can be shaved

better by stretching the skin so

the beard will stand.

• To prevent damaging the system

outer foil, do not shave with only

a part of the system outer foil.

2 Press when nished.

While using After use

The remaining battery

capacity are shown and

then turn off after

5 seconds.

• Approximate amount of

battery capacity is

displayed.

The remaining battery

capacity blink and then

turn off after 5 seconds.

When the battery capacity is low

The lowest battery capacity lamp glows when

operating the shaver.

The appliance beeps twice after switched off.

• You can shave 2 to 3 times. (This will differ

depending on usage.)

Notes

• The appliance may not operate in an ambient

temperature lower than approximately 5 °C.

• The shaving sensor may not respond depending on

the type and quantity of the shaving gel. This is not

abnormal.

• Depending on the beard thickness or the amount of

beard trimmings in the shaver head, the shaving

sensor may not react and the driving sound may not

change. This is not abnormal.

13

English

• To prevent erroneous operation, place your ngers on

the nger rest while using the shaver.

• The sonic vibration cleaning mode is activated when

the power switch is pressed for more than 2 seconds

while the shaver is not operating. (See page 14.)

You cannot shave in this mode.

Operation and display of the switch lock

►Locking the power switch

1. Press once

and then

release.

• The shaver

starts

operating.

2. Press for

more than

2 seconds until

the switch lock

lamp ( ) turns

on.

• The shaver will

stop operating.

3.

Release .

• The switch

lock lamp

() will

light up for

5 seconds

and turn

off.

►Unlocking the power switch

1. Press for more than

2 seconds until the

switch lock lamp ( )

turns off.

2. Once the shaver starts

operating, release .

• The switch lock lamp

() will turn off.

• The power switch is locked when the switch lock lamp

() blinks for 5 seconds and the shaver does not

operate even though the power switch is pressed.

►Using the trimmer

1. Slide the trimmer handle up to

the “ ” position so that the

trimmer stands upright.

2. Press and use.

Press and hold the top knob (

a

)

and slide the trimmer handle

down to lower the trimmer.



Tips for better usage

Apply the trimmer edge perpendicular to skin gently

and move downward slowly.

Trimming sideburns Pre‑shave of long beards

14

English

►Switching the shaver head

You can change the pivot action.

“”

The shaver head is moved to

prevent missed spots.

“ ”

You can lock the shaver head.

Cleaning the shaver

We recommend cleaning the shaver after each use.

Cleaning with water

• Turn the shaver off and disconnect the AC adaptor.

1 Apply some hand soap and

some water to the system

outer foil�

2 Press for more than

2 seconds to activate the

sonic vibration cleaning

mode�

• Splashing of foam is

suppressed.

• The lamps blink alternately.

• After about 20 seconds, it will be automatically

turned off, or you can turn it off by pressing the

power switch.

3 Remove the outer foil

section and clean with

running water�

• See page 15 for removing

the outer foil section.

• Splashing is reduced by rinsing the shaver in sonic

vibration cleaning mode.

• After rinsing with water, shake the shaver up and

down for a few times to remove excess moisture and

then wipe off any drops of water with a dry cloth.

4 Dry the outer foil

section, the shaver, and

the trimmer completely�

• Allow the shaver to dry in

the shade, avoid direct

sunlight.

5 Lubricate the shaver�

It will keep the movement of the

blades smooth and maintain a

comfort shave.

1. Apply one drop of oil to each of

the system outer foils.

2. Raise the trimmer and apply a drop of oil.

3. Switch the shaver on, and run it for approximately

ve seconds.

15

English

4. Switch off the shaver, and wipe off any excess oil

from the system outer foil with a soft cloth.

Notes

• Do not use any kitchen or bathroom detergents other

than hand soap.

Doing so may cause malfunction.

• Be careful not to hit the main body on the sink or any

other object while draining the water. Failure to do so

may cause malfunction.

• Do not wipe with thinners, benzine, alcohol etc.

Doing so may cause malfunction, cracking or

discoloration of the parts.

Wipe with diluted soapy water.

Cleaning with the brush

Remove the outer foil section.

(See this page.)

Clean the system outer foil in the areas

indicated by the circles every time you

use the shaver. Otherwise, abnormal

sound may be generated.

►Cleaning with the long brush

Clean the foil frame, system

outer foil, the main body

and the trimmer using the

long brush.

Replacing the system outer foil

system outer foil once every 18 months

►Removing the outer foil section

Press the foil frame release buttons and

lift the outer foil section upwards.

►Attaching the outer foil section

After turning the foil frame mark ( ) to the

front, securely attach the outer foil section

to the shaver until it clicks.

►Replacing the system outer foil

1. Press the system outer foil release

buttons and pull down the system

outer foil.

• Do not press the system outer foil

release buttons with excessive

force.

Doing so may bend the system outer foil, preventing

complete attachment to the foil frame.

2.

Align the foil frame mark ( ) and the system outer foil

mark ( ) and securely attach together until it clicks.

Note

Do not throw away the foil frame.

16

English

►Replacement parts

Replacement parts are available at your dealer or

Service Centre.

Replacement parts

for ES‑LS6A System outer foil WES9600

FAQ

Question Answer

Does this product

require inner blades?

Outer foils and inner blades

are integrated into the

system outer foil.

Will the battery

deteriorate if not used

for an extended

period of time?

The battery will deteriorate if

not used for over 6 months,

so make sure to perform a

full charge at least once

every 6 months.

Can I charge the

shaver after every

use?

The battery used is a

lithium‑ion, so charging after

every use will have no effect

on battery life.

Why should the

adaptor be

disconnected after

charge?

Charging the battery for more

than 1 hour will not affect

battery performance, but

disconnect the adaptor for

safety and to save energy.

What is the

constituent of the

dedicated oil?

Constituent of the oil is

liquid parafn.

Question Answer

Why does the

appliance beep twice

after switched off?

The sound indicates that the

battery capacity is running

low. Please charge the

appliance.

Troubleshooting

Perform the following actions.

If the problems still cannot be solved, contact the

store where you purchased the unit or a service

centre authorized by Panasonic for repair.

Problem Action

The power switch

does not turn ON.

Unlock the switch lock. (See

page 13.)

17

English

Problem Action

The shaving sensor

does not respond.

Depending on the beard

thickness or the amount of

beard trimmings in the

shaver head, the shaving

sensor may not react and the

driving sound may not

change. This is not abnormal.

The shaving sensor may not

respond depending on the

type and quantity of the

shaving gel. This is not

abnormal.

The shaving sensor may not

respond when the remaining

battery capacity is low. If

this happens, recharge the

shaver.

Apply oil. (See page 14.)

The shaving sensor may not

respond when there is not

enough oil on the system

outer foil.

Problem Action

The shaving sensor

responds even though

the shaver is not in

contact with the skin.

Clean the beard trimmings

from the shaver.

Clean the system outer foil

with the brush. (See

page 15.)

When the shaver is

extremely dirty, remove the

foil frame and wash with

water.

(See page 14.)

Replace the system outer foil.

Expected life of system

outer foil:

Approximately 18 months

18

English

Problem Action

Operating time is

short even after a full

charge.

Although the shaver can be

used for about 2 weeks after

a full charge (assuming

dry‑shave usages for 3

minutes per day), the usable

number of days might be

lower depending on how the

shaver is used (for example,

when used for wet shaving).

Apply oil.

Clean the shaver.

When the number of

operations per charge starts

to decrease, the battery is

nearing the end of its life.

Shaver does not

operate even after

charging.

Use the appliance in an

ambient temperature

approximately 5 °C or higher.

The battery has reached the

end of its life.

The shaver will not operate

with the AC adaptor

connected. Please use the

shaver after it has been

sufciently charged and the

AC adaptor disconnected.

Problem Action

The driving sound

changes while

shaving.

The shaving sensor is

operating. The sound

changes depending on the

beard thickness.

Makes a loud sound.

Apply oil.

The blades will not move

smoothly when there is no

oil on the system outer foil,

requiring more power.

The shaver makes a high‑

pitched sound due to the

linear motor drive. This does

not indicate a problem.

Conrm that the system outer

foil is properly attached.

Clean the system outer foil

with the brush. (See

page 15.)

Wash the system outer foil

with water. (See page 14.)

The odor is getting

stronger. Clean the shaver.

System outer foil gets

hot.

Apply oil.

Replace the system outer

foil if it is damaged or

deformed.

(See page 15.)

19

English

Problem Action

You do not get as

close a shave as

before.

Clean the shaver.

Apply oil.

Replace the system outer foil.

Expected life of system

outer foil:

Approximately 18 months

Battery life

The life of the battery is 3 years. The battery in this shaver

is not intended to be replaced by consumers. Have the

battery replaced by an authorized service centre.

Removing the built-in rechargeable

battery

Remove the built-in rechargeable battery before

disposing of the shaver�

The battery is to be disposed of safely.

Please make sure that the battery is disposed of at an

ofcially designated location if there is one.

This gure must only be used when disposing of the

shaver, and must not be used to repair it. If you

dismantle the shaver yourself, it will no longer be

waterproof, which may cause it to malfunction.

• Remove the shaver from the AC adaptor.

• Press the power switch to turn on the power and then

keep the power on until the battery is completely

discharged.

• Perform steps 1 to 5 and lift the battery, and then

remove it.

• Take care not to short circuit the positive and negative

terminals of the removed battery, and insulate the

terminals by applying tape to them.











For environmental protection and recycling of

materials

This shaver contains a Lithium‑ion battery.

Please make sure that the battery is disposed of at an

ofcially assigned location, if there is one in your country.

20

English

Specications

Power source

See the name plate on the AC

adaptor.

(Automatic voltage conversion)

Motor voltage 3.6 V

Charging time Approx. 1 hour

This product is intended for household use only.

Notes

1. Install on a hard, at surface, except for handheld

parts or xed parts.

2. Store in a dry place indoors.

3. Transport without dropping, excessive vibration or

hitting against other objects.

4. Dispose of according to national and/or local

legislation.

Terms and conditions of sale are not set up by the

manufacturer and must comply with national and/or

local legislation of the country of sale of goods.

Страница загружается ...

Panasonic ES-LS6A Rechargeable Shaver Руководство пользователя

Panasonic ES-LS6A Rechargeable Shaver Руководство пользователя

Похожие модели бренда

Модели других брендов