Yamaha FGDP-50 Руководство пользователя

Finger drum pad

Surface de percussion tactile

Драм-машина

Startup Guide

Kurzanleitung

Guide de démarrage

Guía de inicio

Guia de inicialização

Руководство по запуску

2FGDP-50 FGDP-30 Startup Guide

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the

USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result

in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the

instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations

does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

- Relocate either this product or the device that is being affected by the interference.

- Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

- In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial

type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you

cannot locate the appropriate retailer, please contact Yamaha Corporation of America, 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

(529-M04 FCC class B YCA 02)

FGDP-50 FGDP-30 Startup Guide 3

COMPLIANCE INFORMATION STATEMENT

(Supplier’s declaration of conformity procedure)

Responsible Party: Yamaha Corporation of America

Address: 6600 Orangethorpe Avenue,

Buena Park, CA. 90620, U.S.A.

Telephone: 714-522-9011

Type of Equipment: Finger Drum Pad

Model Name: FGDP-50, FGDP-30

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received, including

interference that may cause undesired operation.

(529-M02 FCC sdoc YCA 02)

This device contains a lithium-ion battery.

After usage, you may recycle the battery, but you never attempt to

remove it by yourself. Have the device inspected by qualified Yamaha

service personnel. If there is no Yamaha personnel in your area,

dispose of it properly according to relevant environmental laws and

disposal rules in your area.

Cet appareil contient une pile au lithium-ion.

Recyclez la pile après utilisation mais ne l'ôtez jamais par vous-même.

Faites inspecter l'unité par un technicien Yamaha qualifié. Si vous ne

trouvez pas de technicien Yamaha qualifié dans votre région, mettez

la pile au rebut conformément aux lois et aux règlementations

environnementales en vigueur localement.

(582-M02)

Important Notice:

U.S. LIMITED WARRANTY for Customers in the

United States

For detailed information about this Yamaha product and warranty

service, please either visit the following website address (printable file

is available at our website) or contact Customer Service at the address

or telephone number identified below.

Website Address:

Yamaha.io/SynthAndStageWarranty

Customer Service:

Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, CA 90620-1273

Telephone: 800-854-1569

PRECAUTIONS

4FGDP-50 FGDP-30 Startup Guide

Contents

PRECAUTIONS ................................................................................................. 4

About the Manuals .................................................................................... 10

Included Accessories ................................................................................. 10

Controls .......................................................................................................... 11

Charging ........................................................................................................ 14

Turning the Power On/Off ....................................................................... 15

Playing the Finger Drum Pads ............................................................... 16

Various Functions (FGDP-50) .................................................................. 19

Various Functions (FGDP-30) .................................................................. 21

Specifications ............................................................................................... 22

Troubleshooting ......................................................................................... 25

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Especially in the case of children, a guardian should provide

guidance on how to properly use and handle the product before

actual use.

Please keep this manual in a safe and handy place for future

reference.

WARNING

Always follow the basic precautions listed below to avoid the

possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire, explosion or other

hazards. These precautions include, but are not limited to,

the following:

Power supply

•Do not place the USB cable near heat sources such as heaters or

radiators. Also, do not excessively bend or otherwise damage

the cable, or place heavy objects on it.

•Do not touch the product, the USB cable or the USB power

adaptor during an electrical storm.

•Use only the correct voltage specified for the product. The

required voltage is printed on the name plate of the product.

•Use only the specified USB power adaptor (page 14).

•Use only the supplied USB cable. Do not use the USB cable for

other devices.

The model number, serial number, power requirements, etc., may be

found on or near the name plate, which is at the bottom of the unit.

You should note this serial number in the space provided below and

retain this manual as a permanent record of your purchase to aid

identification in the event of theft.

Model No.

Serial No.

(1003-M06 plate bottom en 01)

PRECAUTIONS

FGDP-50 FGDP-30 Startup Guide 5

•Check the USB adaptor plug periodically and remove any dirt

or dust which may have accumulated on it.

•Insert the USB power adaptor plug firmly all the way into the

AC outlet. Using the product when it is not plugged in

sufficiently can cause dust to accumulate on the plug, possibly

resulting in fire or skin burns.

•When setting up the product, make sure that the AC outlet you

are using is easily accessible. If some trouble or malfunction

occurs, immediately turn off the power and disconnect the USB

power adaptor plug from the outlet.

•Do not connect the product to an electrical outlet using a

multi-plug outlet extender. Doing so can result in lower sound

quality, or possibly cause overheating in the outlet.

•When disconnecting the cable, always hold the plug itself and

not the cord. Pulling by the cord can damage it and cause

electric shocks or a fire.

•If not using the product for long periods of time, be sure to

disconnect the USB cable and the USB power adaptor from the

AC outlet.

Do not disassemble

•This product contains no user-serviceable parts. Do not

attempt to disassemble the internal parts or modify them in

any way.

Water warning

•Do not expose the product to rain, use it near water or in damp

or wet conditions, or place on it any containers (such as vases,

bottles or glasses) containing liquids which might spill into any

openings or places where water may drop. A liquid such as

water getting into the product may cause a fire, electric shocks,

or malfunctions.

•Never insert or remove a power plug with wet hands.

Fire warning

•Do not place any burning items or open flames near the

product, and do not dispose of product in fire, since they may

cause a fire or explosion.

Handling

•Magnetism from this product may affect electro-medical

devices, such as a heart pacemaker implant or defibrillator

implant.

-Keep the product away from a heart pacemaker implant or a

defibrillator implant.

Batteries

•Do not subject the product to mechanical shock or drop.

Failure to comply may result in fire, electric shock, explosion, or

malfunction.

PRECAUTIONS

6FGDP-50 FGDP-30 Startup Guide

•Do not expose the product to excessive dust or vibrations, or

extreme cold or heat (such as in direct sunlight, near a heater,

or in a car during the day), low air pressure to prevent the

possibility of explosion of built-in battery, product

disfiguration, damage to the internal components or unstable

operation.

•Never charge when the product is wet. Doing so may cause

electric shock, fire, or malfunction due to short circuiting.

•When charging, follow the instructions that came with the

instructions of the connected device. Use only the specified

charger device and within the range of 5°C–35°C.

Charging with an unspecified charger or at a temperature

outside the range may cause leakage, overheating, explosion,

or malfunction.

If you notice any abnormality

•If any of the following problems occur, immediately turn off the

power and disconnect the USB cable from the power source.

Also, avoid touching the product in the following conditions.

Finally have the device inspected by Yamaha service personnel.

-The USB cable or plug becomes frayed or damaged.

-Unusual smells or smoke are emitted.

-When it seems that the product is overheating.

-Some object, or water has been dropped into the product.

-There is a sudden loss of sound during use of the product.

-Cracks or other visible damage appear on the product.

When the power cannot be turned off by normal operation,

press and hold the and buttons at the same time to

turn the power off.

CAUTION

Always follow the basic precautions listed below to avoid the

possibility of physical injury to you or others, or damage to

the product or other property. These precautions include, but

are not limited to, the following:

Location

•Do not place the product in an unstable position or a location

with excessive vibration, where it might accidentally fall over

and cause injury.

•Before moving the product, remove all connected cables, to

prevent damage to the cables or injury to anyone who might

trip over them.

Connections

•Before connecting the product to other devices, turn off the

power for all devices. Before turning the power on or off for all

devices, set all volume levels to minimum.

•Be sure to set the volumes of all devices at their minimum

levels and gradually raise the volume controls while playing the

product to set the desired listening level.

NOTICE

FGDP-50 FGDP-30 Startup Guide 7

Handling

•Do not insert foreign materials such as metal or paper into any

openings or gaps of the product. Failure to observe this may

cause a fire, electric shocks, or malfunctions.

•Do not rest your weight on, or place heavy objects on the

product, and do not use excessive force on the buttons,

switches or connectors.

•Do not use the product or headphones for a long period of

time at a high or uncomfortable volume level, since this can

cause permanent hearing loss. If you experience any hearing

loss or ringing in the ears, consult a physician.

•Remove the USB cable from the AC outlet before cleaning the

unit. Failure to observe this may cause electric shocks.

Always turn off the power when the product is not in use.

Even when the product power is turned off (lamps are off or LCD

screen is off), electricity is still flowing to the product at the

minimum level.

When you are not using the product for a long time, make sure

you unplug the USB cable from the power source.

(DMI-10)

NOTICE

To avoid the possibility of malfunction/damage to the product,

damage to data, or damage to other property, follow the notices

below.

Rechargeable battery

•This product contains a lithium-ion battery.

•Charge the battery every six months to maintain its power. If

you don’t use the battery for a long time, you may not be able

to charge it.

•Rechargeable batteries have a limited lifespan. The capacity

will gradually decrease depending on how it is stored, the

environment in which it is used, how often it is used, and how

much time passes.

•The battery is not removable by the user.

Recycle

•Lithium-ion batteries can be recycled. After

usage, you may recycle the battery, but never

attempt to remove it by yourself. Have the device

inspected by qualified Yamaha service personnel.

If there are no Yamaha service personnel in your

area, dispose of it properly according to relevant

environmental laws and disposal rules in your

area.

Yamaha cannot be held responsible for damage caused by

improper use or modifications to the product, or data that is

lost or destroyed.

NOTICE

8FGDP-50 FGDP-30 Startup Guide

(58-M02 WEEE en 01)

Handling

•Do not use this product in the vicinity of a TV, radio, stereo

equipment, mobile phone, or other electric devices. Otherwise,

this product or the other device may generate noise.

•When you use the product along with an app on your smart

device, such as a smartphone or tablet, we recommend that

you enable “Airplane Mode” on the device to avoid noise

caused by communication.

•Depending on the condition of surrounding radio waves, the

product may possibly malfunction.

•Do not place vinyl, plastic or rubber objects on the product,

since this might discolor the product.

•Do not press the LCD screen on the FGDP-50 with your finger

because it is a sensitive, precision-made part. Doing so might

cause an appearance abnormality, such as a stripe on the LCD,

although this abnormality should disappear again within a

short time.

Maintenance

•When cleaning the product, use a soft and dry (or slightly

damp) cloth. Do not use paint thinners, solvents, alcohol,

cleaning fluids, or chemical-impregnated wiping cloths.

Storage

•Do not expose the product for a long time to excessive dust or

vibrations, or extreme cold or heat (such as in direct sunlight,

Information for users on collection and disposal of

old equipment:

This symbol on the products, packaging, and/or

accompanying documents means that used

electrical and electronic products should not be

mixed with general household waste.

For proper treatment, recovery and recycling of old

products, please take them to applicable collection

points, in accordance with your national legislation.

By disposing of these products correctly, you will

help to save valuable resources and prevent any

potential negative effects on human health and the

environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and

recycling of old products, please contact your local

municipality, your waste disposal service or the

point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic

equipment, please contact your dealer or supplier

for further information.

Information on Disposal in other Countries

outside the European Union:

This symbol is only valid in the European Union. If

you wish to discard these items, please contact your

local authorities or dealer and ask for the correct

method of disposal.

INFORMATION

FGDP-50 FGDP-30 Startup Guide 9

near a heater, or in a car during the day) in order to prevent the

possibility of disfiguration, damage to the internal components

or unstable operation.

•Store with the pad side up. If you store it with the other side

facing up and the pad side down, unstable operation may

result.

Saving data

•Some of the data of this product are stored when the power is

turned off. However, the saved data may be lost due to some

failure, an operational mistake, etc. From the FGDP-50, save

your important data onto a USB flash drive. Information about

the data automatically stored in the product and the USB flash

drives that can be used with the FGDP-50 can be found in the

User Guide (HTML).

•To protect against data loss through USB flash drive damage,

we recommend that you save your important data onto spare

USB flash drive or an external device such as a computer as

backup data.

INFORMATION

About copyrights

•The copyright of the “content”*1 installed in this product

belongs to Yamaha Corporation or its copyright holder. Except

as permitted by copyright laws and other relevant laws, such as

copying for personal use, it is prohibited to “reproduce or

divert”*2 without the permission of the copyright holder. When

using the content, consult with a copyright expert.

If you create music or perform with the contents through the

original use of the product, and then record and distribute

them, the permission of Yamaha Corporation is not required

regardless of whether the distribution method is paid or free of

charge.

*1: The word “content” includes a computer program, audio data,

Accompaniment Style data, MIDI data, waveform data, voice

recording data, music score, and score data, etc.

*2: The phrase “reproduce or divert” includes taking out the content

itself in this product, or recording and distributing it without

changes in a similar manner.

About this manual

•The illustrations as shown in this manual are for instructional

purposes only.

•Unless indicated otherwise, the illustrations as shown in this

manual are based on the FGDP-50.

•The designation “NOTE” as shown in this manual indicates

instructions and supplementary explanations for optimum use.

•The company names and product names in this manual are the

trademarks or registered trademarks of their respective

companies.

About the Manuals

10 FGDP-50 FGDP-30 Startup Guide

Thank you for purchasing the Yamaha Finger Drum Pad FGDP-50 and/or FGDP-30.

These finger drum pad instruments allow you to easily and conveniently play drum and percussion sounds with your fingers.

They were specially designed to be a highly portable ‘mobile drum kit’ that anyone can enjoy anywhere and at any time. In addition,

these instruments are exceptionally useful for experienced finger-drumming players, for beginners who want to learn and get better at

finger drumming, for actual drummers who want to enjoy playing easily, and for composers/producers who want to create original

rhythms.

In order to take full advantage of the FGDP’s functionality and enjoy performing with it, please read this guide carefully before use.

After you have read this guide, keep it in a safe and handy place for future reference.

Included Accessories

•Startup Guide (this book)

•Online Member Product Registration

•USB A – micro-USB B cable (1.5 m)

About the Manuals

The following two manuals are available for the product.

Startup Guide (this book) To help you use the product immediately, these explanations focus on product overview and basic

operations.

User Guide (HTML) This explains all information about this product, including

information provided in the Startup Guide.

https://manual.yamaha.com/mi/de/fgdp50/index_q.html

https://manual.yamaha.com/mi/de/fgdp30/index_q.html

FGDP-50 FGDP-30

Controls

FGDP-50 FGDP-30 Startup Guide 11

Controls

FGDP-50

Click button

(Starting and stopping the click: p.18)

Record button

Playback/Pause button

Stop button

(Playing and recording audio

files: p.19)

Select buttons

Minus/Plus buttons

Exit button

Enter button

(Changing various settings:

p.19)

Registration memory buttons

(Registration Memory: p.20)

Standby/On indicator

(Charging: p.14)

Pads

(Playing the Finger Drum Pads: p.16)

RGB square pads (p.20)

Menu button

Kit button

Audio button

Session Creator button

Registration button

(Changing various settings: p.19)

LCD screen Built-in speaker

LCD screen

Controls

12 FGDP-50 FGDP-30 Startup Guide

FGDP-30

Click lamps and button

Tempo Decrease/Increase buttons

(Starting and stopping the click: p.18)

Lock lamp and button

(Panel Lock: p.21)

Standby/On lamps and button

(Charging: p.14,

Turning the Power On/Off: p.15)

Kit Select buttons

(Selecting the Kit: p.21)

Registration memory buttons

(Registration Memory: p.21)

Select buttons

Minus/Plus buttons

(Changing the settings: p.21)

Built-in speaker

Pads

(Playing the Finger Drum Pads: p.16)

Volume Down/Up buttons

Controls

FGDP-50 FGDP-30 Startup Guide 13

FGDP-50

FGDP-30

Side Back

Standby/On button

(Turning the Power On/Off: p.15)

Up/Down

volume buttons

USB TO DEVICE terminal

* This terminal is for a USB flash drive only.

USB TO HOST

terminal

PHONES/OUTPUT

jack

AUX IN jack

Security slot

Charging

14 FGDP-50 FGDP-30 Startup Guide

Charging

This product can be used after charging by connecting to an AC

outlet or a USB mobile battery in order as illustrated below. In

particular, before using for the first time after unpacking, make

sure to fully charge this product until the Standby/On indicator

(red) turns off.

NOTE

•The product can be used even while charging.

•When battery power is insufficient or abnormal, the Standby/On

indicator (red) or lamp (red) will blink.

•The estimated time from low battery to full charge is 1–3 hours, when

the product power is off (depending on the usage environment and

battery usage.)

•To recharge the battery after a full charge, you will need to unplug the

USB cable, and then connect it again.

USB cable (supplied)

USB power adaptor

(commercially available)

USB mobile battery

(commercially available)

* The shapes of the plug and outlet may

differ depending on your locale.

USB power adaptor / USB mobile battery

requirements

Output voltage DC 5V

Output current 1.5 A or greater USB BC specification

compatible products

CAUTION

Make sure to use a USB power adaptor or USB mobile battery

with the specifications above. Using the wrong adaptors or

batteries can result in damage to the product or overheating.

Follow the instructions that come with the connected USB power

adaptor or the USB mobile battery.

NOTICE

• Use a USB mobile battery that has a low-current mode

function, etc., and can supply power to devices with current

consumption of 25 mA or less. If you cannot charge the battery

with a UBS mobile battery, try a USB power adapter to see if

you can charge the battery from a power outlet.

• When the product is turned on and power turns off suddenly

and unexpectedly, your USB power adaptor or USB mobile

battery may not meet the requirements or may be damaged.

Try using another adaptor or battery that meets the

requirements, etc. If it should appear to be malfunctioning,

please consult Yamaha service personnel.

NOTE

When connected to a computer USB port or a USB power adaptor

with less output current than 1.5 A, the remaining battery power

may decrease even while charging (the Standby/On indicator or

lamp is lit in red).

Turning the Power On/Off

FGDP-50 FGDP-30 Startup Guide 15

Turning the Power On/Off

Turning the power on

Press and hold the button until the LCD screen (FGDP-50) or

lamps (FGDP-30) light.

NOTE

When the battery is empty, the product will not be turned on until it has

been charged to a certain amount.

Turning the power off

Press and hold the button until the LCD screen (FGDP-50) or

lamps (FGDP-30) goes out.

NOTE

•When the power is off, the product settings are saved automatically.

(Some settings may not be saved; refer to the HTML User Guide for

details.)

•When the battery is low, the product will turn off automatically.

Forced power off

If the product behaves abnormally and no operation can be

performed, press and hold the and buttons at the same

time to force the power off.

NOTICE

When forcing the power off, the product settings will not be saved.

Auto Power Off

To prevent unnecessary power consumption, this product

automatically turns the power off after a certain period of

inactivity. The time that elapses before power is automatically

turned off can be changed by the following operations:

FGDP-50:   “Utility”   

“AutoPowerOff” 

(The currently selected item or setting value is shown on the LCD

screen.)

FGDP-30:  “Utility Auto Power Off Time” 

(The currently selected item or setting value is sounded by voice

in English.)

When the power is off, press and hold and (FGDP-50) /

and (FGDP-30) at the same time to turn on the

power, the Auto Power Off Time setting will be “Disabled.”

Playing the Finger Drum Pads

16 FGDP-50 FGDP-30 Startup Guide

Playing the Finger Drum Pads

When you hit the pad with your finger, you will hear the sounds

assigned to each pad. The intensity of the sound changes

according to the strength of your playing. First, try playing a basic

8-beat pattern. We recommend starting out by using your middle

(second) finger to hit the upper hi-hat, your thumb to hit the

lower kick, and your index (first) finger to hit the middle snare.

You can play with either your left or right hand.

C2 H2

R2 R1

M2 M1

T5 T4 T3 T2 T1

H1H3 C1

Pad Layout “Left” (see p.18)

Crash cymbal

Hi-hat cymbal

Splash cymbal

High tom Mid tom

Crash cymbal

Ride cymbal

Low tom

Kick

(Bass drum)

Snare drum

When playing

with the left hand

Back to 1

Playing the Finger Drum Pads

FGDP-50 FGDP-30 Startup Guide 17

Factory-shipped instrument sounds (preset kit 1)

C1, C2 Crash cymbal

H1, H3 Hi-hat cymbal (close)

H2 Hi-hat cymbal (open)

R1 Ride cymbal (cup)

R2 Ride cymbal (bow)

S1 Snare drum (open shot)

S2 Snare drum (open rim shot)

T1, T6 Low tom

T2, T5 Mid tom

T3, T4 High tom

K Kick (bass drum)

M1 Snare drum (closed rim shot)

M2 Splash cymbal

Pad Layout “Right” (factory default)

C1 H2

R1 R2

M1 M2

T2 T3 T4 T5 T6

H3H1 C2

When playing

with the right hand

Back to 1

Playing the Finger Drum Pads

18 FGDP-50 FGDP-30 Startup Guide

NOTICE

This product is designed for playing with the your fingers. Do not hit

the product with anything other than your fingers, such as sticks.

Doing so may cause damage to the product.

Starting and stopping the click

Briefly press (FGDP-50) or (FGDP-30) to start the

click. To stop the click, briefly press the button again.

Changing the tempo

Press or while pressing (FGDP-50) / press or

(FGDP-30) to change the tempo.

If you hit one of the pad three times or more while pressing

(FGDP-50) / (FGDP-30), the tempo will be set by the

average interval between pad hits.

The changed tempo is shown on the LCD screen (FGDP-50) or

sounded by voice in English (FGDP-30).

Changing the pad assignments

The sounds and functions assigned to the pads can be inverted

left or right.

FGDP-50:   “Utility”   

“PadLayout” 

(The currently selected item or setting value is shown on the LCD

screen.)

FGDP-30:  “Utility Pad Layout” 

(The currently selected item or setting value is sounded by voice

in English.)

Various Functions (FGDP-50)

FGDP-50 FGDP-30 Startup Guide 19

Various Functions (FGDP-50)

Changing various settings

The settings can be changed by the following operations.

1. Press one of the buttons and

select the function (mode) you want to change.

2. Briefly press one of the buttons to select

the item you want to set.

Press and hold one of the buttons to continuously scroll

through the items.

(If there are submenus, press to move to the submenu.

Press to return to the menu one level up.)

The currently selected item or setting value is shown on the

LCD screen.

3. Briefly press one of the buttons to change

the value.

Press and hold one of the buttons to continuously scroll

through the values.

Selecting the Kit (sound set)

A Kit is a collection of sounds from different type of musical

instruments, etc. The Kit can be changed by the following

operations.

Move to the home screen of mode (e.g., press

button twice)  select a Kit with .

The Kit name will be shown on the LCD screen.

Press and hold one of the buttons to continuously scroll

though the Kits.

Playing and recording audio files

An audio file on the USB flash drive can be played back while

performance can be recorded to the USB flash drive as an audio

file.

The available audio format is WAV (44.1 kHz, 16-bit, stereo).

Playback: Move to the home screen of mode (e.g., press

button twice)  select an audio file with . Play with

, stop with .

Recording: Press for recording standby  start recording

with  (your performance)  stop recording with .

Using the Session Creator (backing Phrases)

This product provides various full instrumental backing phrases as

a “Session Creator,” which can be played back as accompaniment

to your pad performance. Each phrase consists of six sections:

INTRO, MAIN A, MAIN B, MAIN C, MAIN D and ENDING.

Playback: Move to the home screen of mode (e.g., press

button twice)  select a Session with  hit

[7 START/STOP] of the RGB square pad.

Change Section: Hit one of the [2 INTRO/ENDING] to

[6 MAIN D] of the RGB square pad.

Various Functions (FGDP-50)

20 FGDP-50 FGDP-30 Startup Guide

Stop: Hit [7 START/STOP] of the RGB square pad.

NOTE

You can mute the drum part by briefly pressing [1 DRUM MUTE] of the

RGB square pad or playback only the drum part by briefly pressing

[8 DRUM SOLO] of the RGB square pad.

Registration Memory

A batch of settings can be registered to a button, and you can

recall these settings anytime with a single touch. This convenient

function is called Registration Memory. Register or recall the

settings with the following operations.

Registration: Press and hold one of the

buttons until the LCD screen indicates that registration is

complete.

The current settings will be registered to the pressed button.

Recall: Briefly press one of the buttons.

NOTICE

Do not hold down the button if you just want to recall a registration,

since holding down the button will register and overwrite the

settings.

Panel Lock

To prevent unintended operation by accidentally touching an

unnecessary button during performance, all buttons other than

the pads can be temporarily disabled (locked). Buttons for power

operation and panel unlocking are active even when Panel Lock is

enabled.

Lock: Move to the home screen of each mode (e.g., press

button twice)  press and hold until the LCD screen shows

the panel is locked.

Unlock: Press and hold until the LCD screen shows the

panel is unlocked.

RGB Square Pads

These are self-illuminating pads which light colorfully in time

with performance, making it visually interesting as well as

providing additional pads/sounds for you to play.

In Session Creator (p.19), these are also used to select a

section.

Страница загружается...

Yamaha FGDP-50, FGDP-30 Руководство пользователя

Похожие модели бренда