Sony KV-SZ292 Руководство пользователя

Бренд: Sony

Модель: KV-SZ292

Категория: Телевизоры CRT

Тип: Руководство пользователя

Это руководство также подходит для

Sony KV-ZZ292M91 Group H7 (GB)_3-211-536-E2 (1)

Trinitron Color TV

KV-SZ292

KV-SZ252

3-211-536-E2 (1)

Operating Instructions

• Before operating the unit, please read this manual thoroughly and retain

it for future reference.

M91

01GB01COV-SOEMMIX.p65 19/06/2007, 09:28 AM1

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

A Specifications

Power requirements

Power consumption (W)

Television system

Color system

Stereo/Bilingual stereo

Teletext language

Channel coverage

B/G

D/K

8 (Antenna)

Audio output (Speaker)

Number of terminal

(Video)

(Audio)

(Component

Video)

i (Headphone)

FM Radio

Tuning Range

Intermediate

Frequency

Picture tube

Tube size (cm)

Screen size (cm)

Dimensions (w/h/d)

Mass (kg)

Design and specifications are subject to change without notice.

Note

KV-SZ292M91

KV-SZ252M91

220-240 V AC, 50/60 Hz

Indicated on the rear of the TV

B/G, I, D/K, M

PAL, PAL 60, SECAM, NTSC3.58, NTSC4.43

NICAM Stereo/Bilingual B/G, I, D/K;

A2 Stereo/Bilingual B/G

English, Russian

VHF : E2 to E12 /UHF : E21 to E69 /

CATV : S01 to S03, S1 to S41

UHF : B21 to B68 /CATV : S01 to S03, S1 to S41

VHF : C1 to C12, R1 to R12 /

UHF : C13 to C57, R21 to R60 /

CATV : S01 to S03, S1 to S41, Z1 to Z39

VHF : A2 to A13 /UHF : A14 to A79 /

CATV : A-8 to A-2, A to W+4, W+6 to W+84

75-ohm external terminal

6 W + 6 W

Input: 2 Output: 1 Phono jacks; 1 Vp-p, 75 ohms

Input: 3 Output: 1 Phono jacks; 500 mVrms

Input: 1 Phono jacks;

Y: 1 Vp-p, 75 ohms,

sync negative

B: 0.7 Vp-p, 75 ohms

R: 0.7 Vp-p, 75 ohms

Output: 1 Stereo minijack

87.5 - 108.0 MHz

10.7 MHz

29 in. 25 in.

64 Measured diagonally

60 Measured diagonally

774 × 590 × 506 704 × 530 × 506

46 35

Made in Malaysia.

Manufacturer: Sony Corporation

Address: 1-7-1 Konan, Minota-ku,

Tokyo 108-0075, Japan.

01GB02WAR-SOEMMIX.p65 19/06/2007, 09:29 AM2

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

Clean the TV with a dry and soft

cloth. Do not use benzine, thinner,

or any other chemicals to clean the

TV. Do not attach anything (e.g.,

adhesive tape, cellophane tape,

glue) on the painted cabinet of the

TV. Do not scratch the picture

tube.

B WARNING

• Dangerously high voltages are present inside the TV.

• TV operating voltage: 220 – 240 V AC.

• Do not plug in the power cord until you have completed making all other

connections; otherwise a minimum leakage current might flow through the antenna

and other terminals to ground.

• To avoid battery leakage and damage to the remote, remove the batteries from the

remote if you are not going to use it for several days. If any liquid leaks from the

batteries and touches your skin, immediately wash it away with water.

Install the TV on a stable TV stand

and floor which can support the

TV set weight. Ensure that the TV

stand surface is flat and its area is

larger than the bottom area of the

TV.

Do not plug in too many

appliances to the same power

socket. Do not damage the power

cord.

For children’s safety, do not leave

children alone with the TV. Do not

allow children to climb onto it.

For your own safety, do not touch

any part of the TV, the power cord

and the antenna cable during

lightning storms.

Do not place any objects on the TV.

The apparatus shall not be

exposed to dripping or splashing

and that no objects filled with

liquids, such as vases, shall be

placed on the apparatus.

Do not operate the TV if any liquid

or solid object falls into it. Have it

checked immediately by qualified

personnel only.

Do not block the ventilation

openings of the TV. Do not install

the TV in a confined space, such

as a bookcase or built-in cabinet.

Do not open the cabinet and the

rear cover of the TV as high

voltages and other hazards are

present inside the TV. Refer

servicing and disposal of the TV

to qualified personnel.

To prevent fire or shock hazard, do

not expose the TV to rain or

moisture.

Your TV is recommended for

home use only. Do not use the TV

in any vehicle or where it may be

subject to excessive dust, heat,

moisture or vibrations.

Pull the power cord out by the

plug. Do not pull the power cord

itself. Even if your TV is turned

off, it is still connected to the AC

power source (mains) as long as

the power cord is plugged in.

Unplug the TV before moving it

or if you are not going to use it for

several days.

01GB02WAR-SOEMMIX.p65 19/06/2007, 09:29 AM3

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

C Securing the TV

To prevent the TV from falling, use the supplied screws and band to secure the

TV.

20 mm

3.8 mm

screws band

Screw the band to the TV stand and to the

provided hole at the rear of your TV.

(1) Screw one end of the band to the

provided hole at the rear of your TV.

(2) Securely fix the attached band to a

wall or pillar using an attachment

which can hold the TV.

(1) Attach each end of a cord or chain to

the provided holders at the rear of

your TV.

(2) Securely fix the attached cord or chain

to a wall or pillar using an attachment

which can hold the TV.

• Use only the supplied screws. Use of other screws may damage the TV.

01GB03INS-SOEMMIX.p65 22/06/2007, 10:09 AM4

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

Step 2

Step 1

Insert the batteries (supplied) into the remote.

• Do not use old or different types of batteries together.

Step 3

Step 4

Set up the TV by following the instructions of the

“Initial Setup” menu (see

Plug in the power cord, then press 1 on the TV to

turn it on.

• The 1 (standby) indicator flashes green for a few seconds

when turning on the TV. This does not indicate a

malfunction.

Connect the antenna cable (not supplied) to 8

(antenna input) at the rear of the TV.

•

Your TV can receive both TV and FM radio signals from

the appropriate connections through the 8 (antenna input)

terminal (see

• You can also connect your TV to other optional

components (see

D Getting Started

01GB03INS-SOEMMIX.p65 19/06/2007, 09:30 AM5

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

Program Sorting/Edit

Off

Sorting:

Edit:

PROG

SkipLabel

Exit

Select

Confirm

Start Auto Program now?

Yes

First please connect

cable/ antenna

Initial Setup

End

Select

Confirm

Setting up your TV (“Initial Setup”)

When you turn on your TV for the first time, the “Initial Setup” menu will

appear. You can adjust settings below using the buttons on the remote control or

TV front panel. Press V , v , B or b to select or adjust items, then press

Select the desired menu language.

Select “Yes” to preset the channels automatically.

To skip automatic channel presetting, select “No”.

The “Program Sorting/Edit” menu enables

you to sort and edit the channels (

see

Adjust the bars on the top and bottom of the

menu if they are slanted.

Adjust the upper and lower bars if they are not

equally positioned to the top and bottom of the

screen.

To prevent this “Initial Setup” menu from

appearing again when you turn on the TV by

pressing 1, select “No”.

To allow this menu to appear again, select “Yes”.

• You can immediately go to the end of the “Initial Setup” menu by pressing WEGA

GATE.

Select

Confirm

Initial Setup

Display this menu next time?

Yes

End

Select

Confirm

Select

End

Confirm

01GB03INS-SOEMMIX.p65 19/06/2007, 09:30 AM6

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

(MONO)

F Connecting optional components

You can connect a wide range of optional components to your TV. Connecting

cables are not supplied.

Connecting to the TV (front)

Connecting to the TV (rear)

Camcorder

Audio/Video

cable

• If you connect a VCR to 8 (antenna input), preset the signal output from the VCR to the

program number 0 on the TV (

see

• If your DVD player can output interlace and progressive mode signals, select the

interlace output when connecting to (component video input) on your TV. Your TV

can receive either 525i/60Hz or 625i/50Hz interlace signals.

• The component video terminals on your DVD player are sometimes labeled Y/CB/CR,

Y/PB/PR, Y/Cb/Cr or Y/B-Y/R-Y.

• If you select “DVD” on your TV screen, the signal from the T (monitor output)

terminals will not be output properly. This does not indicate a malfunction.

Audio

cable

Audio/

Video cable

Component

Video cable

Antenna

cable

VCR

If cannot receive

FM signal

VCRDVD player

Audio/

Video cable

(MONO)

Headphones

DVD player

Antenna

cable

signal

Antenna

selector

TV signal

Audio System

TV, CATV, Satellite

01GB03INS-SOEMMIX.p65 19/06/2007, 09:30 AM7

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

G TV buttons and remote control

1 1 Turn off or turn on the TV.

Wake Up indicator.

2 1 Standby indicator.

Remote control sensor.

4 PROG +/– Select program number.

5 2 +/– Adjust volume.

6 t Select TV or video input.

WEGA GATE menu operations (see J)

4,5

, , ,

Select or adjust items.

Confirm selected items.

7 WEGA GATE Display or cancel WEGA GATE

menu.

FM Listen to FM radio (see H).

PROG

A/B

RETURN

WEGA

GATE

1 ?/1 Turn off temporarily or turn on

the TV.

2 a Display the TV program.

Jump to last program number that

has been watched for at least five

seconds.

4 PROG +/– Select program number. To select

quickly, press and hold until the

desired program number appears.

5 2 +/– Adjust volume.

Change the picture size:

“On” (16:9 wide mode), “Off”.

Select surround mode options

(see

Display on-screen information.

qa Mute the sound.

qs A/B Select stereo/bilingual mode:

Broadcasting Display (selected sound)

NICAM stereo NICAM (stereo), Mono (regular)

NICAM bilingual NICAM Main (main), NICAM

Sub (sub), Mono (regular)

NICAM monaural NICAM Main (main), Mono

(regular)

A2 stereo Stereo (stereo), Mono (regular)

A2 bilingual Main (main), Sub (sub)

• If the stereo sound is noisy when receiving a

stereo program, select “Mono”. The sound

becomes monaural, but the noise is reduced.

PROG

12345678

01GB04INS-SOEMMIX.p65 19/06/2007, 09:31 AM8

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

t Select TV or video input.

qf 0-9 Input numbers. For program numbers 10 and above, enter the second

digit within two seconds.

ql Select sound mode options with a 5-Band Graphic Equalizer display:

“Dynamic”, “Standard”, “Custom”* (see

100 300 1k 3k 8k

Dynamic

100 300 1k 3k 8k

Standard

100 300 1k 3k 8k

Custom

* When the “Custom” mode is selected, you can receive the last adjusted

sound settings from the “Sound Adjustment” option in the menu.

w; Select picture mode options: “Vivid”, “Standard”, “Custom”*

(see

* When the “Custom” mode is selected, you can receive the last adjusted

picture settings from the “Picture Adjustment” option in the menu.

WEGA GATE menu operations (see

)

Confirm selected items.

7 WEGA GATE Display or cancel WEGA GATE menu.

V, v, B, b Select or adjust items.

qk RETURN Return to the previous level.

Timer operations

Set TV to turn on automatically according to the desired period of time

(Wake Up Timer) (max. of 12 hours). The indicator on TV lights up amber once you set

the wake up timer. If no buttons or controls are pressed for more than

three hours after the TV is turned on using the wake up timer, the TV

automatically goes into standby mode.

Set TV to turn off automatically according to the desired period of time

(Sleep Timer) (max. of one hour and 30 min.).

Teletext operations (green icon)

Display Teletext broadcast: Teletext t Teletext and TV t TV. If there is

no Teletext broadcast, only “100” is displayed at the top left corner of the

screen.

Display Teletext service contents.

0-9 Input three digits Teletext page number.

Display the next or previous page.

Stop Teletext display from scrolling.

Reveal concealed information.

Enlarge the Teletext display.

Show TV screen while waiting for Teletext page. Enter the Teletext page

number that you want to refer to, then press . When the page number

is displayed, press to show the text.

(red, green, Access the corresponding colored FASTEXT menu. The FASTEXT

yellow, blue) feature can be used only when the FASTEXT broadcast is available.

PIP operations

, , V, v, B, b Not function for your TV.

01GB04INS-SOEMMIX.p65 19/06/2007, 09:31 AM9

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

H Listening to the FM Radio

You are able to listen to the FM radio stations using your TV by connecting an

antenna (see

To access to FM Radio mode:

Press WEGA GATE button and select “FM Radio” (see

Press FM button on the front panel (see

To exit from FM Radio mode:

Press WEGA GATE button, select the desired items: “TV” or “External Inputs”,

then press

. Select the desired TV channel or external inputs and press .

Press FM button on the front panel.

A/B

PROG

+/–

V, v,

B, b

WEGA

GATE

PROG

A/B

WEGA

GATE

RETURN

Listening to preset stations

Access to FM Radio mode.

Press WEGA GATE button and select “Settings”.

Preset the desired FM radio stations in “FM Radio

Setup” from “Channel Setup” menu (see

Exit from “Channel Setup” menu by pressing

WEGA GATE button. The selected preset FM radio

station number and label will appear on the screen.

To select the desired preset FM radio station, press

PROG +/–.

• You can also use the 1-9 buttons on the remote control

to directly select the desired preset FM radio station.

Listening to non-preset stations

Access to FM Radio mode.

Press V or v to search for the desired FM radio station. The preset number

and label will not be displayed.

•

You can only operate V, v, B and b functions using the remote control buttons in FM

Radio mode.

•

The available radio frequency is only for temporary listening pleasure and cannot be

stored in the memory.

•

If the message “Please setup FM Radio” appears, display the “Channel Setup” menu

and select “FM Radio Setup” to preset the desired FM radio stations (see

• If the station has a noisy sound, you may be able to improve the sound quality by pressing

B or b.

• When a FM stereo program has static noise, press A/B until “Mono” appears. There will

be no stereo effect, but the noise will be reduced.

01GB04INS-SOEMMIX.p65 19/06/2007, 09:31 AM10

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

I Troubleshooting

If you find any problem while viewing your TV, you can either use the

“Factory Settings” function (see

) or check the Troubleshooting guide

below. If the problem persists, contact your Sony dealer.

Snowy picture, noisy sound

• Check the antenna setup and other connections.

• Preset the channel manually again (see

• Set the “Signal Booster” to “Auto” (see

) or try using an external booster.

Distorted picture, noisy sound

• Set the “Signal Booster” to “Off” (see

), or turn off or disconnect any external booster in

use.

Good picture, noisy sound

• Select the appropriate “TV System” (see

No picture, no sound

• Check the power cord, antenna setup and other connections.

• Press 4/1 (power) to turn on the TV.

• Press 1 (main power) on the TV to turn off the TV for about five seconds, then turn it on

again.

Good picture, no sound

• Press 2 + to increase the volume level or press to cancel the muting.

Dotted lines or stripes

• Do not use a hair dryer or other equipment near the TV.

• Check the antenna setup.

Double images or “ghosts”

• Use the fine tuning (“Fine”) function (see

• Check the antenna setup or use a highly directional antenna.

• Turn off or disconnect any external booster in use.

No color

• Adjust the “Color” level from “Picture Adjustment” (see

• Select the appropriate “Color System” (see

• Check the antenna setup.

Picture slant

• Keep external speakers or other electrical equipment away from the TV.

• Adjust the “Picture Rotation” or “Picture V-Position” (see

Abnormal color patches

• Keep external speakers or other equipment away from the TV. Do not move the TV while

the TV is turned on. Press 1 (main power) on the TV to turn off the TV for about 15

minutes, then turn it on again to demagnetize the TV.

Teletext display is incomplete (snowy picture or double images).

• Check the antenna setup and other connections.

• Set the “Signal Booster” to “Auto” (see

) or try using an external booster.

• Use the fine tuning (“Fine”) function (see

01GB04INS-SOEMMIX.p65 19/06/2007, 09:31 AM11

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

TV cannot receive stereo broadcast sound or stereo broadcast sound switches on and off or is distorted.

• Check the antenna setup and other connections.

TV cannot receive FM radio station.

• Connect a separate FM antenna and the TV channel source through an antenna selector

(switch) to your TV (see F).

The 1 (standby) indicator on your TV flashes red several times after every three seconds.

• Count the number of times the 1 (standby) indicator flashes. Press 1 on the TV to turn it

off, disconnnect the AC power cord and inform your dealer or Sony service center of how

the indicator flashes (duration and interval).

The TV screen sometimes goes blank for slightly longer than usual during channel change.

• The “Signal Booster” is functioning to detect a weak signal. This does not indicate a

malfunction.

TV cabinet creaks.

• Changes in room temperature sometimes make the TV cabinet expand or contract, causing

a noise. This does not indicate a malfunction.

A small “boom” sound is heard when the TV is turned on.

• The TV’s demagnetizing function is working. This does not indicate a malfunction.

Troubleshooting (continued)

01GB04INS-SOEMMIX.p65 19/06/2007, 09:31 AM12

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

Confirm

End

Picture

Color Temperature: Cool

Picture Adjustment

Picture Mode: Vivid

VM: High

Intelligent Picture: On

Signal Level Indicator: On

Select

Confirm

Select

End

External Inputs

Confirm

Select

End

Video 1

DVD

Video 2

Confirm

Select

WEGA GATE

Settings

External Inputs

FM Radio

Preset 1:

---.--

Please setup FM Radio

FM Radio

Select Preset 1-9

Exit

Fine

Confirm

Select

End

Confirm

Select

End

J WEGA GATE navigator

WEGA GATE is a gateway that allows you access to preset TV channels,

connected external inputs, FM Radio mode and “Settings” menu.

watch the preset TV

channels (see

)

select the inputs for the

connected equipment

(see

)

listen to the FM radio

(see

)

How to use WEGA GATE

(1) Press WEGA GATE to display or cancel

the WEGA GATE menu.

Confirm

Select

WEGA GATE

Settings

External Inputs

FM Radio

(2) Press (or b) to confirm your selection

or go to the next level.

(4) Press RETURN to move to the previous

level.

(3) Press V or v to select the desired item.

“TV”

“External Inputs”

“FM Radio”

Confirm

Select

WEGA GATE

Settings

External Inputs

FM Radio

• When a feature is dimmed in the menu, it is not selectable.

• The WEGA GATE, and

, , ,

buttons on the front panel can also be used for

the operations above.

“Settings”

change the settings

of your TV

(see

)

01GB05AVD-SOEMMIX.p65 19/06/2007, 09:32 AM13

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

Confirm

End

Picture

Color Temperature: Cool

Picture Adjustment

Picture Mode: Vivid

VM: High

Intelligent Picture: On

Signal Level Indicator:

Select

K “Picture” setting

Press WEGA GATE and select “Settings”.

Make sure the “Picture” icon (

) is selected,

then press .

“Picture Mode” Choose either “Vivid” (bright, contrast and sharp),

“Standard” (normal) or “Custom”*.

“Color Temperature” Adjust white color tint.

Choose either “Cool” (blue tint), “Neutral” (neutral tint) or

“Warm” (red tint).

“VM” Sharpen the edges of each object.

(Velocity Modulation) Choose either “High”, “Low” or “Off”.

“Intelligent Picture” Optimize picture quality.

Press V or v to select “On”, then press .

To cancel, select “Off”, then press .

“Signal Level Indicator” Display the signal level when the “Intelligent Picture” is

functioning.

“Intelligent Picture Signal Level” indicator will be displayed,

followed by picture improvement when you change the

program number or the input mode.

red amber green

(weak) (average)(fair ................. good)

Press V or v to select “On”, then press .

To cancel, select “Off”, then press . “Intelligent Picture” is

still functioning.

* You can adjust the setting to your personal preference in the “Picture Adjustment”,

“Color Temperature” and “VM” options only when the “Custom” mode is selected.

01GB05AVD-SOEMMIX.p65 19/06/2007, 09:32 AM14

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

Adjusting the “Picture Adjustment” items under “Custom”

mode

Press V or v to select either “Picture” (contrast), “Brightness”, “Color”,

“Hue” (color tones) or “Sharpness”, then press

Selecting “Reset” will set your TV to the factory settings.

Press V,v,B or b to adjust the setting of your selected item, then press .

Repeat the above steps to adjust other items.

The adjusted settings will be received when you select “Custom”.

• “Hue” can be adjusted for the NTSC color system only.

• Reducing “Sharpness” can also reduce picture noise.

“Picture” setting (continued)

01GB05AVD-SOEMMIX.p65 19/06/2007, 09:32 AM15

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

Confirm

End

Sound

Balance

Sound Adjustment

Sound Mode: Dynamic

Intelligent Volume: Off

Surround: Off

Select

L “Sound” setting

Press WEGA GATE and select “Settings”.

Press V or v to select the “Sound” icon (

then press

“Sound Mode” Choose either “Dynamic” (low and high tones), “Standard”

(voice and high tones) or “Custom”*

“Balance” Press v or B to emphasize the left speaker.

Press V or b to emphasize the right speaker.

“Intelligent Volume” Adjust the volume of all program numbers and video inputs

automatically.

Press V or v to select “On”, then press .

To cancel, select “Off”, then press .

“Surround” Choose either “On” (surround), “Simulated” (stereo-like

monaural sound) or “Off”.

* You can adjust the setting to your personal preference in the “Sound Adjustment”

option only when the “Custom” mode is selected.

Adjusting the “Sound Adjustment” items under “Custom”

mode

The 5-Band Graphic Equalizer feature allows you to adjust sound frequency settings

of “Custom” mode in the menu.

Make sure that “Adjust” is selected, then press .

Selecting “Reset” will set your TV to the factory settings.

Press B or b to select the desired sound frequency, then press V or v to

adjust the setting and press

The adjusted settings will be received when you select “Custom”.

• Adjusting higher frequency will affect higher pitched sound and adjusting lower

frequency will affect lower pitched sound.

• You may display the settings directly by using the button on the remote control

(see

01GB05AVD-SOEMMIX.p65 19/06/2007, 09:32 AM16

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

“Channel Setup” setting

Press WEGA GATE and select “Settings”.

Press V or v to select the “Channel Setup”

icon (

), then press .

“Auto Program” Preset channels automatically.

“Manual Program” Manually preset desired channels and channels that cannot

be preset automatically (see Presetting channels manually).

“Program Sorting/Edit”

Sort and edit the channels.

(a) If you wish to keep the channels in the current condition,

press WEGA GATE to exit.

(b) Press

V or v to select the program number with the

channel you wish to change. The selected channel will

appear on the screen.

(1) Press b to enter sorting mode.

(2) Press V or v to select the new program number

position for your selected channel, then press B.

(d) If you wish to edit the channels, press to change to

edit mode.

Press b until the mode that you wish to edit is

highlighted: Label, Skip, (block symbol). Then press

(1) To label, press V or v to select the alphanumeric

characters for the label. Then press .

(2) To skip the program number, press V or v to select

“On”. Then press .

You can skip this program number when using

PROG +/–.

(3) To block unwanted program number, press V or v to

select . Then press .

(e) Repeat step (b) to (d) if you wish to change other

channels.

Press WEGA GATE to exit.

Confirm

End

Channel Setup

Select

Auto Program

Manual Program

Program Sorting/Edit

FM Radio Setup

01GB05AVD-SOEMMIX.p65 19/06/2007, 09:32 AM17

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

“Channel Setup” setting (continued)

“FM Radio Setup”* Preset up to nine FM radio stations.

You can manually preset each FM radio station that can be

received in your area and then store the radio frequency of the

desired FM radio stations.

(1) Press

V or v

to select the desired FM radio station

position, then press .

(2) Press

V or v

o search the FM radio stations.

Searching stops automatically when a station is tuned in.

If the station has a noisy sound, you may be able to improve

the sound quality by pressing

B or b

Press to store the FM radio station.

(3) You may edit the FM radio station label. Press

V or v

select alphanumeric characters for the label, then press

(4) Repeat steps (1) through (3) to preset other FM radio

stations.

* The “FM Radio Setup” feature is only available in FM

Radio mode. To

enable this feature, access to FM Radio

mode by using WEGA GATE system (see

) or

pressing the FM button on the front panel (see

then preset your desired FM radio stations according to

the steps mentioned above.

• If you preset a blocked program number, that program number will be unblocked

automatically.

• If you sort a blocked program, that program will remain blocked.

01GB05AVD-SOEMMIX.p65 19/06/2007, 09:32 AM18

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

VHF Low

Fine:

TV System:

D/K

Confirm

Select

Auto

Signal Booster:

Auto

End

Manual Program

Program

Presetting channels manually

After selecting “Manual Program”, select the program

number to which you want to preset a channel.

(1) Make sure “Program” is selected, then press

(2) Press V or v

until the program number you want

to preset appears on the menu, then press

Select the desired channel.

(1) Make sure either “VHF Low”, “VHF High” or “UHF” is selected, then press

(2) Press V or v until the desired channel’s broadcast appears on the TV screen,

then press .

If the sound of the desired channel is abnormal, select the appropriate TV

system.

(1) Press V or v

to select “TV System”, then press .

(2) Press V or v

until the sound becomes normal, then press .

If you are not satisfied with the picture and sound quality, you may be able

to improve them by using the “Fine” tuning feature.

(1) Press V or v

to select “Fine”, then press .

(2) Press V or v

to select “Manual”, then press .

(3)

Press V, v, B or b until the picture and sound quality are optimal, then press .

The + or – icon on the menu flashes while tuning.

If the TV signal is too strong (picture distorted; picture with lines; signal

interference) or weak (snowy picture), you may be able to improve the

picture quality by setting the “Signal Booster” feature.

(1) Press V or v

to select “Signal Booster”, then press .

(2) Press V or v

to select either “Off” (for picture distorted; picture with lines;

signal interference) or “Auto” (for snowy picture), then press

01GB05AVD-SOEMMIX.p65 19/06/2007, 09:32 AM19

Black

Sony KV-SZ292M91 Group H7 (GB)_3-211-536-E2 (1)

“Setup” setting

Press WEGA GATE and select “Settings”.

Press V or v to select the “Setup” icon (

then press .

“Language” Change the menu language.

Press V or v to select either “English” or “Русский” (Russian),

then press .

“Picture Position” Adjust the picture position when it is not aligned with the TV

screen.

Press V or v to select “Picture Rotation” or “Picture V-Position”,

then press .

Press V,v,B or b to adjust the picture position, then press .

“Video Label” Label the connected equipment.

(1) Select “Video Input” and press . Press V or v to select the

input you want to label, then press .

(2) Select “Label” and press , then press V or v to select

the label options: “Video 1”/“Video 2” / “DVD”, “VCR”,

“SAT”, “Game” or “Edit”*.

* You may edit the video label to your favorite name. Press V or v

to select alphanumeric characters for the label, then press .

“Color System” Select the color system.

Press V or v to select either “Auto”, “PAL”, “SECAM”,

“NTSC3.58” or “NTSC4.43”, then press . Normally, set this to

“Auto”.

“Factory Settings”

Reset your TV to factory settings.

Press and press V or v to select “Yes”. Then press .

Your TV will go blank for a few seconds, then the “Initial Setup”

menu will appear.

To cancel, select “No”, then press .

• Color system is not selectable in FM Radio mode.

Confirm

End

Setup

Select

Language:

Picture Position

Video Label

Color System: Auto

Factory Settings

English

01GB05AVD-SOEMMIX.p65 19/06/2007, 09:32 AM20

Black

Страница загружается ...

Sony KV-SZ292 Руководство пользователя

Бренд: Sony

Модель: KV-SZ292

Категория: Телевизоры CRT

Тип: Руководство пользователя

Это руководство также подходит для

Скачать PDF

сообщить о нарушении

Sony KV-SZ292 Руководство пользователя

Это руководство также подходит для

Sony KV-SZ292 Руководство пользователя

Похожие модели бренда