Yamaha DSP-Z7 Инструкция по применению

Категория
Аудио-видео ресиверы
Тип
Инструкция по применению
© 2008 Yamaha Corporation All rights reserved.
Printed in Malaysia WQ21600
En
AV Amplifier
OWNER’S MANUAL
English
RBGLE
DSP-Z7_RBGLE_cv.fm Page 1 Wednesday, September 17, 2008 4:00 PM
Black process 45.0° 240.0 LPI
2 En
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
3 Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in an environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign objects may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections
are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury. Yamaha
will not be held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
16 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
17 Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
18 Before moving this unit, press
B
MASTER ON/OFF to
release it outward to the OFF position to turn off this unit, the
main room, Zone 2, Zone 3, and Zone 4 and then disconnect
the AC power plug from the AC wall outlet.
19
VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC wall outlet. Voltages are:
..................................AC 110/120/220/230–240 V, 50/60 Hz
20 The batteries shall not be exposed to excessive heat such as
sunshine, fire or like.
21 Excessive sound pressure from earphones and headphones can
cause hearing loss.
22 When replacing the batteries, be sure to use batteries of the
same type. Danger of explosion may happen if batteries are
incorrectly replaced.
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
Special Instructions for U.K. Model
Caution: Read this before operating your unit.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
As long as this unit is connected to the AC wall outlet,
it is not disconnected from the AC power source even
if you turn off this unit by
B
MASTER ON/OFF. In
this state, this unit is designed to consume a very small
quantity of power.
Note
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
Caution: Read this before operating your unit.
3 En
Limited Guarantee for European Economic Area (EEA) and Switzerland
Thank you for having chosen a Yamaha product. In the unlikely event that your Yamaha product needs guarantee service, please contact the dealer from
whom it was purchased. If you experience any difficulty, please contact Yamaha representative office in your country. You can find full details on our
website (http://www.yamaha-hifi.com/ or http://www.yamaha-uk.com/ for U.K. resident).
The product is guaranteed to be free from defects in workmanship or materials for a period of two years from the date of the original purchase. Yamaha
undertakes, subject to the conditions listed below, to have the faulty product or any part(s) repaired, or replaced at Yamaha’s discretion, without any charge
for parts or labour. Yamaha reserves the right to replace a product with that of a similar kind and/or value and condition, where a model has been
discontinued or is considered uneconomic to repair.
Conditions
1. The original invoice or sales receipt (showing date of purchase, product code and dealer’s name) MUST accompany the defective product, along with a
statement detailing the fault. In the absence of this clear proof of purchase, Yamaha reserves the right to refuse to provide free of charge service and the
product may be returned at the customer’s expense.
2. The product MUST have been purchased from an AUTHORISED Yamaha dealer within the European Economic Area (EEA) or Switzerland.
3. The product must not have been the subject of any modifications or alterations, unless authorised in writing by Yamaha.
4. The following are excluded from this guarantee:
a. Periodic maintenance and repair or replacement of parts due to normal wear and tear.
b. Damage resulting from:
(1) Repairs performed by the customer himself or by an unauthorised third party.
(2) Inadequate packaging or mishandling, when the product is in transit from the customer. Please note that it is the customer’s responsibility to
ensure the product is adequately packaged when returning the product for repair.
(3) Misuse, including but not limited to (a) failure to use the product for its normal purpose or in accordance with Yamaha’s instructions on the proper
use, maintenance and storage, and (b) installation or use of the product in a manner inconsistent with the technical or safety standards in force in
the country where it is used.
(4) Accidents, lightning, water, fire, improper ventilation, battery leakage or any cause beyond Yamaha’s control.
(5) Defects of the system into which this product is incorporated and/or incompatibility with third party products.
(6) Use of a product imported into the EEA and/or Switzerland, not by Yamaha, where that product does not conform to the technical or safety
standards of the country of use and/or to the standard specification of a product sold by Yamaha in the EEA and/or Switzerland.
(7) Non AV (Audio Visual) related products.
(Products subject to “Yamaha AV Guarantee Statement” are defined in our website at http://www.yamaha-hifi.com/ or
http://www.yamaha-uk.com/ for U.K. resident.)
5. Where the guarantee differs between the country of purchase and the country of use of the product, the guarantee of the country of use shall apply.
6. Yamaha may not be held responsible for any losses or damages, whether direct, consequential or otherwise, save for the repair or replacement of the
product.
7. Please backup any custom settings or data, as Yamaha may not be held responsible for any alteration or loss to such settings or data.
8. This guarantee does not affect the consumer’s statutory rights under applicable national laws in force or the consumer’s rights against the dealer arising
from their sales/purchase contract.
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical
and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national legislation and the Directives 2002/96/
EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and
prevent any potential negative effects on human health and the environment which could otherwise
arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your
local municipality, your waste disposal service or the point of sale where you purchased the items.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact
your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
4 En
Features.................................................................... 7
Supplied accessories .................................................. 7
Logos and trademarks................................................ 8
Getting started......................................................... 9
Quick start guide...................................................10
Preparation: Check the items................................... 10
Step 1: Set up your speakers.................................... 11
Step 2: Connect your DVD player and
other components ........................................ 12
Step 3: Turn on the power and start playback ......... 13
Connections ........................................................... 14
Rear panel ................................................................ 14
Placing speakers ...................................................... 15
Connecting speakers ................................................ 17
Information on jacks and cable plugs ...................... 20
Information on HDMI™.......................................... 21
Audio and video signal flow.................................... 22
Connecting a TV monitor or projector .................... 23
Connecting other components ................................. 24
Using the VIDEO AUX jacks on the front panel .... 29
Connecting the power cable .................................... 29
Setting the speaker impedance and
display language .................................................. 30
Turning this unit on and off ..................................... 30
Front panel display .................................................. 31
Using the remote control ......................................... 32
Opening and closing the front panel door ............... 33
Optimizing the speaker setting for
your listening room ........................................... 34
Before starting the automatic setup ......................... 34
Quick automatic setup ............................................. 34
Basic automatic setup .............................................. 35
Advanced automatic setup....................................... 37
Reviewing and reloading the automatic setup
parameters ........................................................... 39
Playback ................................................................ 41
Basic procedure ....................................................... 41
Selecting audio input jacks (AUDIO SELECT)...... 42
Selecting the multi-channel input component ......... 42
Selecting the HDMI OUT jack................................ 42
Using your headphones ........................................... 43
Muting the audio output .......................................... 43
Displaying the input source information ................. 43
Using the sleep timer ............................................... 44
Sound field programs ........................................... 45
Selecting sound field programs ............................... 45
Using CINEMA DSP 3D mode............................... 51
Enjoying unprocessed input sources........................ 51
Using audio features ............................................. 52
Selecting decoders ................................................... 52
Enjoying pure hi-fi sound ........................................ 53
Adjusting the tonal quality ...................................... 53
Adjusting the speaker level...................................... 54
Selecting the recording source................................. 54
Using Bluetooth™ components ........................... 55
Pairing the Bluetooth™ receiver and
your Bluetooth component .................................. 55
Playback of the Bluetooth™ component................. 55
Music Content menu ............................................ 56
Music Content menu operations .............................. 56
Using iPod™.......................................................... 57
iPod menu tree ......................................................... 57
Controlling iPod™ .................................................. 58
Using USB and network features ........................ 59
USB and network menu tree.................................... 59
Navigating USB and network menus ...................... 60
Using a USB storage device or
a USB portable audio player ............................... 61
Using a PC server or Yamaha MCX-2000 .............. 61
Using the Internet Radio.......................................... 62
Using shortcut buttons ............................................. 62
Contents
INTRODUCTION
PREPARATION
BASIC OPERATION
5 En
PREPARATIONINTRODUCTION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
Graphical user interface (GUI) menu................. 64
GUI menu overview ................................................ 66
GUI menu operations............................................... 67
Stereo/Surround ....................................................... 68
Input Select .............................................................. 73
Music Content.......................................................... 75
Setup (Speaker)........................................................ 75
Setup (Volume)........................................................ 77
Setup (Sound) .......................................................... 78
Setup (Video)........................................................... 81
Setup (HDMI).......................................................... 83
Setup (Network)....................................................... 84
Setup (Multi Zone) .................................................. 85
Setup (Option) ......................................................... 87
Language.................................................................. 90
Saving and recalling the system settings
(System Memory).............................................. 91
Saving the system settings ....................................... 91
Loading the system settings..................................... 92
Using examples........................................................ 93
Controlling this unit by using the Web browser
(Web Control Center) ...................................... 95
Remote control features ....................................... 96
Controlling this unit, a TV, or other components.... 96
Customizing the remote control............................... 98
Setting the backlight mode of the remote control.... 99
Setting remote control codes ................................... 99
Programming codes from other remote controls ... 101
Changing source names in the display window..... 102
Macro programming features ................................ 103
Clearing configurations ......................................... 105
Simplified remote control ...................................... 106
Using multi-zone configuration ......................... 107
Connecting the Zone 2,
Zone 3 and Zone 4 components ........................ 107
Controlling Zone 2, Zone 3 or Zone 4................... 110
Using the party mode............................................. 112
Advanced setup................................................... 113
Using the advanced setup menu ............................ 113
Troubleshooting...................................................116
Resetting the system............................................126
Operation modes of front panel controls ..........127
Glossary................................................................128
Sound field program information......................131
Parametric equalizer information .....................132
Specifications .......................................................133
Index .....................................................................134
Front panel...............................................................2
Remote control ........................................................3
Sound output in each sound field program...........4
List of remote control codes ...................................6
Information about software .................................11
ADVANCED OPERATION ADDITIONAL INFORMATION
APPENDIX (separate booklet)
6 En
By configuring the parameters in the GUI menu of this unit, you can adjust a variety of system settings suited for your
listening environment. The following is a brief description of some of the useful menus you can configure in the GUI
menu. For more detailed information, see “Graphical user interface (GUI) menu” (page 64).
Fine adjusting the speaker settings
In case speaker settings configured by automatic setup
does not match your listening environment, you can
configure them manually.
Setup Speaker (page 75)
Specifying the muting type
In case you do not want to fully mute audio when you
receive a call while watching your favorite TV program,
you can use this menu to specify the muting level.
Setup Vo l u m e Muting Type (page 78)
Specifying the initial volume level
By adjusting this parameter, you can automatically control
the initial volume level regardless of the recording level of
the audio source.
Setup Vo l u m e Initial Volume (page 78)
Adjusting the dynamic range
The dynamic range is the difference between the
minimum and maximum amplitude. The higher the
dynamic range, the more accurate the sound reproduction
for bitstream signals. You can adjust the dynamic range
for speakers and headphones individually. Also, you can
use the adaptive dynamic range control feature to adjust
the dynamic range automatically in conjunction with the
volume level.
Setup Sound Dynamic Range (page 78)
Setup Vo l u m e Adaptive DRC (page 77)
Adjusting the audio and video synchronization
Sometimes, depending on your video source component,
video is delayed relative to audio due to processing
problems. In this case, you need to manually adjust the
audio delay to keep it synchronized with the video. If you
connect the video source component to this unit using an
HDMI connection and your component supports the
LIPSYNC feature, you can adjust the audio/video
synchronization automatically.
Setup Sound Lipsync (page 80)
Changing input/output assignment
In case the initial input/output assignments do not
correspond to your needs, you can rearrange them
according to your component to be connected to this unit.
You can also edit the input name to be displayed in the
front panel or in the GUI screen as necessary.
Setup Option I/O Assignment (page 87)
Setup Option Input Rename (page 88)
Fixing the volume difference between input
sources
The sound output level may vary depending on the audio
source components connected to this unit. In this case, you
can reduce or increase the output level of each input
source using this feature.
Input Select (input source) (submenu)
Volume Trim (page 73)
Setting the background video for discrete multi-
channel input
If you want to enjoy video images in combination with
discrete multi-channel audio input, configure this setting
to specify the video input source. For example, to view
DVD video images while listening to the music sources
from a multi-format player or an external decoder, set this
setting to “DVD”.
Input Select MULTI CH (submenu)
BGV (page 74)
Adjusting the brightness of the front panel
display
You can make the front panel display darker or brighter by
configuring this setting.
Setup Option Display Set Front Panel Display
Dimmer (page 88)
Turning on or off the short message display
Each time you operate this unit using controls on the front
panel or remote control keys, this unit displays short
messages on the video monitor. If you want to turn off the
short message display, select “Off” in this setting (Initial
factory setting is “On”).
Setup Option Display Set
Short Message (page 88)
Setting the amount of time to display GUI screen
information
You can set the amount of time to display playback
information in the GUI screen after you perform a certain
operation.
Setup Option Display Set
Playback Screen (page 88)
Protecting the setup values
After you have configured the sound field program
parameters and other system settings, you can use this
feature to prevent accidental changes to those setup
values.
Setup Option Memory Guard (page 87)
What you can do with the GUI menu
FEATURES
7 En
INTRODUCTION
Built-in 7-channel power amplifier
Minimum RMS output power
(20 Hz to 20 kHz, 0.04% THD, 8 Ω)
Front: 140 W + 140 W
Center: 140 W
Surround: 140 W + 140 W
Surround back: 140 W + 140 W
Various input/output connectors
HDMI (IN x 5, OUT x 2), Component video (IN x 3, OUT x 1),
S-video (IN x 6, OUT x 3), Composite video (IN x 6, OUT x 5),
Coaxial digital audio (IN x 3), Optical digital audio
(IN x 5, OUT x 2), Analog audio (IN x 11, OUT x 3)
Speaker out (7-channel), Pre out (7-channel), Subwoofer out,
Presence out, Zone 2/Zone 3/Zone 4 out
Discrete multi-channel input (6 or 8-channel)
Sound field programs
Proprietary Yamaha technology for the creation of sound
fields
CINEMA DSP 3D
Compressed Music Enhancer mode
Virtual CINEMA DSP
SILENT CINEMA
Digital audio decoders
Dolby TrueHD, Dolby Digital Plus decoder
DTS-HD Master Audio, DTS-HD High Resolution Audio
decoder
Dolby Digital/Dolby Digital EX decoder
DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS 96/24 decoder
Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx
decoder
DTS NEO:6 decoder
HDMI™ (High-Definition Multimedia Interface)
HDMI interface for standard, enhanced or
high-definition video as well as multi-channel digital audio
based on HDMI version 1.3a (HDMI is licensed by HDMI
Licensing, LLC.)
Automatic audio and video synchronization (lip sync)
information capability
Deep Color video signal (30/36 bit) transmission capability
“x.v.Color” video signal transmission capability
High refresh rate and high resolution video signals
capability
High definition digital audio format signals capability
HDCP (High-bandwidth Digital Content Protection System)
licensed by Digital Content Protection, LLC.
Analog video to HDMI digital video up-conversion
(composite video S-video component video HDMI
digital video) capability for monitor out
Analog and HDMI video up/down: 480i(576i) 480p(576p)/
720p/1080i/1080p, 480p(576p) 720p/1080i/1080p, 720p
480p(576p)/1080i/1080p, 1080i 480p(576p)/720p/
1080p, 1080p 480p(576p)/720p/1080i
HDMI image quality adjustment feature
DOCK terminal
DOCK terminal to connect a Yamaha iPod universal dock
(such as YDS-11, sold separately) or Bluetooth wireless audio
receiver (such as YBA-10, sold separately)
USB and network features
USB port to connect a USB storage device, USB Hard disc
drive, or USB portable audio player
NETWORK port to connect a PC and Yamaha MCX-2000 or
access the Internet Radio via LAN
DHCP automatic or manual network configuration
Web control capability of this unit by using a Web browser
Automatic speaker setup features
Advanced YPAO (Yamaha Parametric room Acoustic
Optimizer) for automatic speaker setup
Multi-point measurement feature for multiple listening
positions
Speaker angle measurement feature
Parametric equalizer select feature
Other features
192-kHz/24-bit D/A converter
GUI (graphic user interface) menus that allow you to optimize
this unit to suit your individual audiovisual system
Music Content menu that allows you to easily navigate music
content menus of your iPod, USB component, Internet Radio,
etc.
PURE DIRECT mode for pure hi-fi sound for all sources
Adaptive dynamic range controlling capability
Adaptive DSP effect level controlling capability
Remote control with preset remote control codes, learning and
macro capability
ZONE 2/ZONE 3/ZONE 4 custom installation facility
Zone switching capability between the main zone and
ZONE2/ZONE3/ZONE4 using ZONE CONTROLS
System Memory capability for saving and recalling multiple
system parameter settings
Sleep timer for each zone
Check that you received all of the following parts.
Remote control
Simplified remote control
Batteries (4) (AAA, LR03, UM-4)
Power cable (Two for Asia model)
Optimizer microphone
Microphone base
Features
Supplied accessories
Features
8 En
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic and the double-D symbol are trademarks of
Dolby Laboratories.
Manufactured under license under U.S. Patent No’s:
5,451,942;5,956,674;5,974,380;5,978,762;6,226,616;6,487,535
& other U.S. and worldwide patents issued & pending. DTS is a
registered trademark and the DTS logos, Symbol, DTS-HD and
DTS-HD Master Audio are trademark of DTS, Inc. © 1996-2007
DTS, Inc. All Rights Reserved.
“iPod” is a trademark of Apple Inc., registered in the U.S. and
other countries.
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
This amplifier supports network connections.
“HDMI”, the “HDMI” logo and “High-Definition Multimedia
Interface” are trademarks, or registered trademarks of HDMI
Licensing LLC.
x.v.Color™
“x.v.Color” is a trademark of Sony Corporation.
“SILENT CINEMA” is a trademark of Yamaha Corporation.
The Certified For Windows Vista logo, Windows Media and the
Windows logo are trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries.
Content providers are using the digital rights management
technology for Windows Media contained in this device
(WMDRM) to protect the integrity of their content (Secure
Content) so that their intellectual property, including copyright, in
such content is not misappropriated.
This device uses WM-DRM software to play Secure Content
(WM-DRM Software).
If the security of the WM-DRM Software in this device has been
compromised, owners of Secure Content (Secure Content
Owners) may request that Microsoft revoke the WM-DRM
Software’s right to acquire new licenses to copy, display and/or
play Secure Content. Revocation does not alter the WM-DRM
Software’s ability to play unprotected content. A list of revoked
WM-DRM Software is sent to your device whenever you
download a license for Secure Content from the Internet or from a
PC. Microsoft may, in conjunction with such license, also
download revocation list onto your device on behalf of Secure
Content Owners.
Logos and trademarks
iPod
TM
GETTING STARTED
9 En
INTRODUCTION
Installing batteries in the remote control
1 Take off the battery compartment cover.
2 Insert the four supplied batteries
(AAA, LR03, UM-4) according to the polarity
markings (+ and –) on the inside of the
battery compartment.
3 Snap the battery compartment cover back
into place.
Change all of the batteries if you notice the following
conditions:
the operation range of the remote control decreases.
the transmit indicator does not flash or its light becomes dim.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
If the remote control is without batteries for more than 2
minutes, or if exhausted batteries remain in the remote control,
the contents of the memory may be cleared. When the memory
is cleared, insert new batteries, set up the remote control code
and program any acquired functions that may have been
cleared.
VOLTAGE SELECTOR
(Asia and General models only)
Getting started
About this manual
y indicates a tip for your operation.
Some operations can be performed by using either the
buttons on the front panel or the ones on the remote
control. In case the button names differ between the front
panel and the remote control, the button name on the
remote control is given in parentheses.
This manual is printed prior to production. Design and
specifications are subject to change in part as a result of
improvements, etc. In case of differences between the
manual and product, the product has priority.
•“
B
MASTER ON/OFF” or “
3
DVD” (example)
indicates the name of the parts on the front panel or the
remote control. Refer to the attached sheet or “Appendix”
(separate booklet) for the information about each position
of the parts.
1
3
2
Notes
Caution
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local voltage BEFORE
plugging the power cable into the AC wall outlet.
Improper setting of the VOLTAGE SELECTOR may
cause damage to this unit and create a potential fire
hazard.
Rotate the VOLTAGE SELECTOR clockwise or
counterclockwise to the correct position using a straight
slot screwdriver.
Voltages are as follows:
..........................AC 110/120/220/230–240 V, 50/60 Hz
230-
240V
VOLTAGE
SELECTOR
Voltage indication
QUICK START GUIDE
10 En
The following steps describe the easiest way to enjoy DVD movie playback in your home theater.
In these steps, you need the following supplied
accessories.
Power cable
The following items are not included in the package of this
unit.
Speakers
Front speaker ..................................... x 2
Center speaker ................................... x 1
Surround speaker .............................. x 4
Select magnetically shielded speakers. The
minimum required speakers are two front speakers.
The priority of the requirement of other speakers is
as follows:
1. Two surround speakers
2. One center speaker
3. One (or two) surround back speaker(s)
Active subwoofer ................................... x 1
Select an active subwoofer equipped with an RCA
input jack.
Speaker cable ......................................... x 7
Subwoofer cable ..................................... x 1
Select a monaural RCA cable.
DVD player .............................................. x 1
Select DVD player equipped with coaxial digital
audio output jack and composite video output
jack.
Video monitor .......................................... x 1
Select a TV monitor, video monitor or projector
equipped with a composite video input jack.
Video cable ............................................. x 2
Select RCA composite video cables.
Digital coaxial audio cable .................... x 1
Quick start guide
Front right
speaker
Subwoofer
Surround back
right speaker
Surround left
speaker
Front left
speaker
Surround back left
speaker
Surround right
speaker
Center
speaker
Video monitor
DVD player
Enjoy DVD playback!
Step 1: Set up your speakers
P. 11
Step 2: Connect your DVD player
and other components
Step 3: Turn on the power and
start playback
P. 12
P. 13
Preparation: Check the items
Quick start guide
11 En
INTRODUCTION
Place your speakers in the room and connect them to this
unit.
1 Place your speakers and subwoofer in the
room.
2 Connect speaker cables to each speaker.
3 Connect each speaker cable to the
corresponding speaker terminal of this unit.
1 Make sure that this unit and the subwoofer are
unplugged from the AC wall outlets.
2 Twist the exposed wires of the speaker cables
together to prevent short circuits.
3 Do not let the bare speaker wires touch each other.
4 Do not let the bare speaker wires touch any metal
part of this unit.
Be sure to connect the left channel (L), right channel
(R), “+” (red) and “–” (black) properly.
Front speakers and center speaker
Surround and surround back speakers
4 Connect the subwoofer cable to the
SUBWOOFER PRE OUT jack of this unit and
the input jack of the subwoofer.
Step 1: Set up your speakers
AC IN
SPEAKERS
CENTERSURROUND BACK/BI-AMP PRESENCE/ZONE 2/ZONE 3
FRONT SURROUND ZONE 2/ZONE 3
SINGLE
NETWORK USB
VIDEO
S VIDEO
MONITOR OUT
VIDEO
REMOTE
PHONO
GND
CD TV
HDMI
COMPONENT VIDEO
AUDIO
DOCK
DIGITAL INPUT
MULTI CH INPUT
PRE OUT
TRIGGER OUT
RS-232C
DIGITAL OUTPUT
ZONE OUT
SUB SUR.BACK
WOOFER
SUB
WOOFER
CENTERZONE 4 OUT
CENTER
FRONT(6CH)
FRONT
SURROUND
SURROUND
PRESENCE
SUR.BACK/
SINGLE(SB)
ZONE 2
ZONE 3 ZONE
VIDEO
CD
D
V
D
D
V
R
COAXIAL
1
2
TV
BD/
HD DVD
CBL/
SAT
MD/
CD-R
DVD ZONE 4
OPTICAL
87
65
4
321
(8CH)
DVD
OUT
(REC)
IN
(PLAY)
MD/CD-RTUNER
BD/HD DVD
VCR
DVR
CBL/SAT
OUT OUT
ININ
BD/HD DVD DVD CBL/SAT
MONITOR OUT/
ZONE OUT
Y
P
R
P
B
Y
P
R
P
B
IN 1 2
OUT IN OUT
DVR
CBL/
SAT
OUT
1
OUT
2
+
A B C
R
R
L
R
L
+
R
L
+
+
R
L
+
R
L
+
R
L
L
IN1
IN3
DVD
BD/
HD DVD
IN2
IN4
SP1
SP2
AC OUTLETS
SWITCHED
SUBWOOFER PRE OUT Speaker terminals
12 3 4
12 3 4
To the front left
speaker
To the front right
speaker
Loosen Insert
To the center
speaker
Tighten
To the surround
back
right speaker
To the surround
right speaker
To the surround back
left speaker
To the surround left
speaker
SUBWOOFER PRE OUT jack
Input jack
AV amplifierSubwoofer
Subwoofer cable
Quick start guide
12 En
1 Connect the digital coaxial audio cable to the
digital coaxial audio output jack of your DVD
player and the DVD DIGITAL INPUT COAXIAL
jack of this unit.
2 Connect the video cable to the composite
video output jack of your DVD player and
DVD VIDEO jack of this unit.
3 Connect the video cable to the VIDEO
MONITOR OUT jack of this unit and the video
input jack of your video monitor.
4 Connect the supplied power cable to this unit
and then plug of the power cable and other
components into the AC wall outlet.
y
For details about connecting the power cable, see page 29.
For other connections
Other speaker combinations P. 17
Information on jacks and cable plugs P. 20
Information on HDMI™ P. 21
TV monitor or projector P. 23
Other components P. 24
External amplifier P. 26
Multi-format player or external decoder P. 27
Yamaha iPod universal dock or
Bluetooth wireless audio receiver P. 27
•Network P. 28
USB device P. 28
Step 2: Connect your DVD player
and other components
AC IN
SPEAKERS
CENTERSURROUND BACK/BI-AMP PRESENCE/ZONE 2/ZONE 3
FRONT SURROUND ZONE 2/ZONE 3
SINGLE
NETWORK USB
VIDEO
S VIDEO
MONITOR OUT
VIDEO
REMOTE
PHONO
GND
CD TV
HDMI
COMPONENT VIDEO
AUDIO
DOCK
DIGITAL INPUT
MULTI CH INPUT
PRE OUT
TRIGGER OUT
RS-232C
DIGITAL OUTPUT
ZONE OUT
SUB SUR.BACK
WOOFER
SUB
WOOFER
CENTERZONE 4 OUT
CENTER
FRONT(6CH)
FRONT
SURROUND
SURROUND
PRESENCE
SUR.BACK/
SINGLE(SB)
ZONE 2
ZONE 3 ZONE
VIDEO
CD
D
V
D
D
V
R
COAXIAL
1
2
TV
BD/
HD DVD
CBL/
SAT
MD/
CD-R
DVD ZONE 4
OPTICAL
87
65
4
321
(8CH)
DVD
OUT
(REC)
IN
(PLAY)
MD/CD-RTUNER
BD/HD DVD
VCR
DVR
CBL/SAT
OUT OUT
ININ
BD/HD DVD DVD CBL/SAT
MONITOR OUT/
ZONE OUT
Y
P
R
P
B
Y
P
R
P
B
IN 1 2
OUT IN OUT
DVR
CBL/
SAT
OUT
1
OUT
2
+
A B C
R
R
L
R
L
+
R
L
+
+
R
L
+
R
L
+
R
L
L
IN1
IN3
DVD
BD/
HD DVD
IN2
IN4
SP1
SP2
AC OUTLETS
SWITCHED
Make sure that this unit and the DVD
player are unplugged from the AC
wall outlets.
VIDEO MONITOR OUTDVD VIDEO
DVD DIGITAL INPUT
COAXIAL
Digital coaxial
audio output
jack
Digital coaxial audio
cable
DVD DIGITAL INPUT
COAXIAL jack
DVD player
AV amplifier
Composite video
output jack
Video cable
DVD VIDEO jack
DVD player
AV amplifier
Video monitor
AV amplifier
Video cable
VIDEO MONITOR
OUT jack
Video input jack
Quick start guide
13 En
INTRODUCTION
1 Turn on the video monitor connected to this
unit.
2 Press BMASTER ON/OFF inward to the ON
position on the front panel.
3 Rotate the
I
INPUT selector to set the input
source to “DVD”.
4 Start playback of the desired DVD on your
player.
5 Rotate
M
VOLUME to adjust the volume.
6 To set this unit to the standby mode, press
AMAIN ZONE ON/OFF.
y
For details about turning on/off this unit and the standby
mode, see page 30.
For other operations
Optimizing the speaker parameters
automatically P. 34
Basic playback operations P. 41
Sound field programs P. 45
Pure high-fidelity sounds P. 53
Bluetooth component playback P. 55
iPod playback P. 57
Playback via USB or network P. 59
Step 3: Turn on the power and start
playback
Check the type of the connected speakers.
If the speakers are 6-ohm speakers, set “SPEAKER
IMP.” to “6Ω MIN” before using this unit (page 30).
You can also use 4-ohm speakers as the front speakers
(page 113).
14 En
The RS-232C terminal is a control expansion terminal for
factory use only. Consult your dealer for details.
Connections
Rear panel
AC IN
SPEAKERS
CENTERSURROUND BACK/BI-AMP PRESENCE/ZONE 2/ZONE 3
FRONT SURROUND ZONE 2/ZONE 3
SINGLE
NETWORK USB
VIDEO
S VIDEO
MONITOR OUT
VIDEO
REMOTE
PHONO
GND
CD TV
HDMI
COMPONENT VIDEO
AUD IO
DOCK
DIGITAL INPUT
MULTI CH INPUT
PRE OUT
TRIGGER OUT
RS-232C
DIGITAL OUTPUT
ZONE OUT
SUB SUR.BACK
WOOFER
SUB
WOOFER
CENTERZONE 4 OUT
CENTER
FRONT(6CH)
FRONT
SURROUND
SURROUND
PRESENCE
SUR.BACK/
SINGLE(SB)
ZONE 2
ZONE 3 ZONE
VIDEO
CD
D
V
D
D
V
R
COAXIAL
1
2
TV
BD/
HD DVD
CBL/
SAT
MD/
CD-R
DVD ZONE 4
OPTICAL
87
65
4
321
(8CH)
DVD
OUT
(REC)
IN
(PLAY)
MD/CD-RTUNER
BD/HD DVD
VCR
DVR
CBL/SAT
OUT OUT
ININ
BD/HD DVD DVD CBL/SAT
MONITOR OUT/
ZONE OUT
Y
P
R
P
B
Y
P
R
P
B
IN 1 2
OUT IN OUT
DVR
CBL/
SAT
OUT
1
OUT
2
+
A B C
R
R
L
R
L
+
R
L
+
+
R
L
+
R
L
+
R
L
L
IN1
IN3
DVD
BD/
HD DVD
IN2
IN4
SP1
SP2
AC OUTLETS
SWITCHED
AB0
9
C
231458
76
Name Page
1 HDMI jacks 21
2 COMPONENT VIDEO jacks 20
3 Audio component jacks 20
REMOTE IN/OUT jacks 27, 107
4 Video component jacks 20
5 NETWORK port 28
6 USB port 28
7 VOLTAGE SELECTOR
(Asia and General models only)
9
8 AC IN 29
AC OUTLET(S) 29
9 DOCK terminal 27
0 DIGITAL INPUT/OUTPUT jacks 20
A TRIGGER OUT jacks 109
B RS-232C terminal
C MULTI CH INPUT jacks 27
PRE OUT jacks 26
ZONE OUT jacks 107
Speaker terminals 17
Note
15 En
Connections
PREPARATION
The speaker layout below shows the speaker setting we recommend.
y
7.1-channel speaker layout is highly recommended for playback of the high definition digital audio sources (Dolby TrueHD, DTS-HD
Master Audio, etc.) with sound field programs.
We recommend that you add the presence speakers for the effect sounds of the CINEMA DSP sound field program.
The surround back speakers and presence speakers do not output sound simultaneously.
7.1-channel speaker layout (plus presence speakers)
6.1-channel speaker layout
5.1-channel speaker layout
Placing speakers
FR
FL
SBR
SBL
SL
SR
C
SW
PL
PR
60˚
30˚
SBR
SBL
FL
FR
PL
PR
C
SL
SR
SR
80˚
SL
30 cm (12 in) or more
60˚
30˚
SB
FL
FR
C
SL
SR
SR
80˚
SL
FR
FL
SB
SL
SR
C
SW
FR
FL
SL
SR
SW
C
60˚
30˚
FL
FR
C
SL
SR
SR
80˚
SL
16 En
Connections
Speaker types
Front left and right speakers (FL and FR)
The front speakers are used for the main source sound plus
effect sounds. Place these speakers at an equal distance
from the ideal listening position. The distance of each
speaker from each side of the video monitor should be the
same.
Center speaker (C)
The center speaker is for the center channel sounds
(dialog, vocals, etc.). If for some reason it is not practical
to use a center speaker, you can do without it. Best results,
however, are obtained with the full system.
Surround left and right speakers (SL and SR)
The surround speakers are used for effect and surround
sounds.
For 5.1-channel speaker layout, place these speakers
farther back compared with the placement in the 7.1-
channel speaker layout.
Surround back left and right speakers (SBL and
SBR)/Surround back speaker (SB)
The surround back speakers supplement the surround
speakers and provide more realistic front-to-back
transitions.
For 6.1-channel speaker layout, surround back left and
right channel signals are mixed down and output at the
single surround back speaker by configuring the
“Surround Back” setting (page 76).
For 5.1-channel speaker layout, surround back left and
right channel signals are output at the surround left and
right speakers by configuring the “Surround Back” setting
(page 76).
Subwoofer (SW)
The use of a subwoofer with a built-in amplifier, such as
the Yamaha Active Servo Processing Subwoofer System,
is effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the high
fidelity sound of the LFE (low-frequency effect) channel
included in bitstreams and multi-channel PCM sources.
The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better
to place the subwoofer near the front speakers. Turn it
slightly toward the center of the room to reduce wall
reflections.
Presence left and right speakers (PL and
PR)
The presence speakers supplement the sound from the
front speakers with extra ambient effects produced by the
sound field programs (page 45). We recommend that you
use the presence speakers especially for the CINEMA
DSP sound field programs. To use the presence speakers,
connect the speakers to SP1 speaker terminals and then set
“Front Presence” to “Yes” (page 76).
For other speaker combinations
You can enjoy multi-channel sources with sound field
programs by using a speaker combination other than
the 7.1/6.1/5.1-channel speaker combinations.
Use the automatic setup feature (page 34) or set the
“Speaker” parameters (page 75). to output the surround
sounds at the connected speakers.
FR
PRPL
C
FL
1.8 m (6 ft)
0.5 to 1 m (1 to 3 ft) 0.5 to 1 m (1 to 3 ft)
1.8 m (6 ft)
17 En
Connections
PREPARATION
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,
this unit cannot reproduce the input sources accurately.
A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a
stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the
plain cable to the “–” (black) terminals.
You can connect both surround back and presence speakers to this unit, however they do not output sound simultaneously. This unit
automatically switches the presence speakers and surround back speakers depending on the input sources and the selected sound field
programs.
7.1-channel speaker connection
Connecting speakers
Caution
Before connecting the speakers, make sure that this unit is turned off (page 30).
Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could
damage this unit and/or speakers.
Use magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the
speakers away from the monitor.
If you are to use 6-ohm speakers, be sure to set “SPEAKER IMP.” to “6Ω MIN” before using this unit (page 30).
You can also use 4-ohm speakers as the front speakers (page 113).
Notes
SPEAKERS
CENTERSURROUND BACK/BI-AMP PRESENCE/ZONE 2/ZONE 3
FRONT SURROUND ZONE 2/ZONE 3
SINGLE
+
R
L
+
R
L
+
+
R
L
+
R
L
+
R
L
SP1
SP2
SUB
WOOFER
Front speakers Surround speakers
Presence speakers
(page 16) or
Zone 2/Zone 3
speakers
(page 107)
Subwoofer
Right
Center speaker
Surround back speakers
Left
Left
LeftRightRight
Zone 2/Zone 3 speakers
(page 107)
18 En
Connections
6.1-channel speaker connection
5.1-channel speaker connection
Surround back speaker
SPEAKERS
CENTERPRESENCE/ZONE 2/ZONE 3
FRONT SURROUND ZONE 2/ZONE 3
SINGLE
L
+
R
L
+
+
R
L
+
R
L
+
R
L
SP1
SP2
SUB
WOOFER
Surround speakers
Front speakers
Presence speakers
(page 16) or
Zone 2/Zone 3 speakers
(page 107)
Subwoofer
Center speaker
Left
Left
Right Right
Zone 2/Zone 3
speakers
(page 107)
SPEAKERS
CENTERSURROUND BACK/BI-AMP PRESENCE/ZONE 2/ZONE 3
FRONT SURROUND ZONE 2/ZONE 3
SINGLE
+
R
L
+
R
L
+
+
R
L
+
R
L
+
R
L
SP1
SP2
SUB
WOOFER
Surround speakersFront speakers
Subwoofer
Center speaker
LeftLeft
Right
Right
Zone 2/Zone 3
speakers (page 107)
Front speakers for the
bi-amplification
connections
(page 19)
Presence speakers
(page 16) or
Zone 2/Zone 3 speakers
(page 107)
19 En
Connections
PREPARATION
Connecting the speaker cable
1 Remove approximately 10 mm (0.4 in) of
insulation from the end of each speaker
cable and then twist the exposed wires of the
cable together to prevent short circuits.
2 Loosen the knob, insert one bare wire into
the hole and then tighten the knob.
Connecting the banana plug
(Except U.K., Europe, Asia and Korea
models)
Tighten the knob and then insert the banana plug
into the end of the terminal.
Using bi-amplification connections
You can make bi-amplification connections to one speaker
system which supports bi-amplification connection as
shown below. To activate the connections, configure the
“BI-AMP” setting (page 114).
When you make the conventional connection with the speakers,
make sure that the shorting bars are put into the terminals of the
speakers appropriately. Refer to the instruction manuals of the
speakers for details.
10 mm (0.4 in)
Loosen Insert Tighten
Banana plug
Caution
Remove the shorting bars or bridges of your speakers to
separate the LPF (low pass filter) and HPF (high pass filter)
crossovers.
Note
SURROUND BACK/BI-AMP
FRONT
SINGLE
+
R
L
+
R
L
This unit
LeftRight
Front speakers
20 En
Connections
This unit has three types of audio jacks, three types of video jacks and HDMI jacks. You can choose the connection
method depending on the component to be connected.
Audio jacks
AUDIO jacks
For conventional analog audio signals transmitted via left
and right analog audio cables. Connect red plugs to the
right jacks and white plugs to the left jacks.
COAXIAL jacks
For digital audio signals transmitted via coaxial digital
audio cables.
OPTICAL jacks
For digital audio signals transmitted via optical digital
audio cables.
You can use the digital jacks to input PCM, Dolby Digital and
DTS bitstreams. When you connect components to both the
COAXIAL and OPTICAL jacks, priority is given to the signals
input at the COAXIAL jack. All digital input jacks are
compatible with up to 96-kHz sampling digital signals.
Video jacks
VIDEO jacks
For conventional composite video signals transmitted via
composite video cables.
S VIDEO jacks
For S-video signals, separated into the luminance (Y) and
chrominance (C) video signals transmitted on separate
wires of S-video cables.
COMPONENT VIDEO jacks
For component video signals, separated into the
luminance (Y) and chrominance (P
B, PR) video signals
transmitted on separate wires of component video cables.
y
This unit is equipped with the video conversion function.
(page 22)
Information on jacks and cable plugs
Note
COAXIAL
DIGITAL
AUDIO
OPTICAL
DIGITAL
R
L
C
O
R
L
Left and right
analog audio
cable plugs
Optical
digital
audio cable
plug
Coaxial
digital audio
cable plug
(Red)(White) (Orange)
VIDEO S VIDEO
COMPONENT VIDEO
Y
R
P
B
P
PB
Y
P
R
S
V
Composite
video cable
plug
S-video
cable plug
Component
video cable
plugs
(Yellow) (Green) (Blue) (Red)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154

Yamaha DSP-Z7 Инструкция по применению

Категория
Аудио-видео ресиверы
Тип
Инструкция по применению

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ