Pioneer DEH-1800UB Руководство пользователя

Бренд: Pioneer

Модель: DEH-1800UB

Категория: Мультимедиа-приемники для автомобилей

Тип: Руководство пользователя

Это руководство также подходит для

English Français Italiano Español Deutsch Nederlands Русский

CD RDS RECEIVER

AUTORADIO CD RDS

SINTOLETTORE CD RDS

REPRODUCTOR DE CD CON RECEPTOR RDS

CD RDS-EMPFÄNGER

CD RDS-ONTVANGER

CD RDS ПРИЕМНИК

DEH-1800UB

DEH-1800UBG

DEH-1800UBA

DEH-1800UBB

DEH-1801UB

Owner’s Manual

Mode d’emploi

Manuale d’istruzioni

Manual de instrucciones

Bedienungsanleitung

Handleiding

Руководство пользователя

2En

Before You Start....................................................................................... 2

Getting Started........................................................................................ 3

Radio.......................................................................................................... 5

CD/USB/AUX............................................................................................. 6

Using Pioneer ARC APP.......................................................................... 7

Settings ..................................................................................................... 8

FUNCTION settings ................................................................................. 8

AUDIO settings......................................................................................... 8

SYSTEM settings ...................................................................................... 9

ILLUMINATION settings....................................................................... 10

Connections/Installation ..................................................................... 10

Additional Information ........................................................................ 12

About this manual:

• In the following instructions, a USB memory or USB audio player are referred to as

“USB device”.

Table of Contents

Thank you for purchasing this PIONEER product

To ensure proper use, please read through this manual before using this product. It is especially

important that you read and observe WARNINGs and CAUTIONs in this manual. Please keep the

manual in a safe and accessible place for future reference.

Private households in the member states of the EU, in Switzerland and Norway may return their used

electronic products free of charge to designated collection facilities or to a retailer (if you purchase a

similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of

disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery

and recycling and thus prevent potential negative effects on the environment and human health.

WARNING

• Do not attempt to install or service this product by yourself. Installation or servicing of this

product by persons without training and experience in electronic equipment and automotive

accessories may be dangerous and could expose you to the risk of electric shock, injury or other

hazards.

• Do not attempt to operate the unit while driving. Make sure to pull off the road and park your vehicle

in a safe location before attempting to use the controls on the device.

CAUTION

• Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock could result.

Also, damage to this unit, smoke, and overheating could result from contact with liquids.

• Always keep the volume low enough to hear outside sounds.

• The CarStereo-Pass is for use only in Germany.

• This product is evaluated in moderate and tropical climate condition under the Audio, video and

similar electronic apparatus - Safety requirements, IEC 60065.

Before You Start

If you want to dispose this product, do not mix it with general household waste. There is a separate

collection system for used electronic products in accordance with legislation that requires proper

treatment, recovery and recycling.

CAUTION

This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007.

3En

English

If you experience problems

Should this unit fail to work properly, please contact your dealer or nearest authorized PIONEER Service

Station.

DEH-1800UB/1800UBG/1800UBA/1800UBB/1801UB

Remote Control

NOTE

Remote control is supplied only for DEH-1801UB.

Getting Started

Basic operation

SRC (source)/OFF

Detach button

Display window

M.C. (multi-control) dial

BAND/

DISP (display)

SRC (source)

VOLUME +/–

MUTE

DISP (display)

FUNCTION

AUDIO

Frequently used operations

The available buttons vary depending on the unit.

* When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control terminal,

the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the

source off.

Display indication

Purpose

Operation

Head Unit Remote Control

Turn on the power* Press SR

C/OFF to turn on

the power.

Press and hold SRC/OF

F to

turn off the power.

Press SRC to

turn on the

power.

Press and hold SRC to

turn

off the power.

Adjust the volume Turn the M.

C. dial. Press VOLUME + or –.

Press MU

TE to mute the

unit. Press again to unmute.

Select a source Press SR

C/OFF repeatedly. Press SRC repeatedly.

Change the display

info

rmation

Press DISP repeatedly. Press DISP repeatedly.

Return to the previous

isplay/list

Press BAND/ . Press / to select the

next/previous folder.

Return to the normal display

om the menu

Press and hold BAND/ .

–

Indication Description

Appears when a lower tier of the menu or folder exists.

Appears when the button is pressed.

Appears when the local seek tuning function is set (page 8).

Appears when a traffic program is received.

Appears when the TA (traffic announcements) function is set (page 8).

Appears when the sound retriever function is set (page 8).

Appears when random play is set.

Appears when repeat play is set.

4En

Detach the front panel to prevent theft. Remove any cables and devices attached to the

ont panel and turn off the unit before detaching it.

Important

• Avoid subjecting the front panel to excessive shock.

• Keep the front panel out of direct sunlight and high temperatures.

• Always store the detached front panel in a protective case or bag.

Remove the insulation sheet before use.

WARNING

• Do not ingest the battery, Chemical Burn Hazard.

• This product, including the supplied remote control, contains a coin/button cell battery. If the coin/

button cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to

death.

• Keep new or used batteries out of the reach of children. If the battery is swallowed or placed inside

any part of the body, consult a doctor immediately.

• If the battery compartment does not close securely, stop using the product and keep it away from

children.

Detaching the front panel

Preparing the remote control

Detach Attach

How to replace the battery

Insert the CR2025 (3 V) battery with the plus (+) and

minus (–) poles orientated properly.

• Do not expose the battery or remote control to excessive heat such as direct sunlight or fire.

CAUTION

• There is a potential danger of explosion if the battery is incorrectly replaced. When replacing the

battery, replace it with the same type.

• Do not handle or store the battery with metallic tools or objects.

• If the battery leaks, remove the battery and wipe the remote control completely clean. Then install a

new battery.

• When disposing of used batteries, please comply with governmental regulations or environmental

public institutions’ rules that apply in your country/area.

Important

• Do not store the remote control in high temperatures or direct sunlight.

• Do not let the remote control fall onto the floor, where it may become jammed under the brake or

accelerator pedal.

When you turn the ignition switch to ON after installation, [SET UP :YES] appears in the

display.

1 Press the M.C. dial.

The setup menu disappears after 30 seconds of no operation. If you prefer not to set

t this time, turn the M.C. dial to select [NO], then press to confirm.

2 Turn the M.C. dial to select the options, then press to confirm.

To proceed to the next menu option, you need to confirm your selection.

3 [QUIT :YES] appears when all the settings have been made.

To return to the first item of the setup menu, turn the M.

C. dial to select [QUIT :NO],

then press to confirm.

4 Press the M.C. dial to confirm the settings.

NOTES

• You can cancel the menu setting by pressing SRC/OFF.

Setup menu

Menu Item Description

LANGUAGE Select the language to display the text information from a

mpressed audio file.

[ENG](English),

[РУС

](Russian),

[TUR](Turkish)

CLOCK SET Set the clock.

FM STEP Select the FM tuning step from 100 kHz or 50 kHz.

[100], [50]

5En

English

• These settings can be made at any time from the SYSTEM settings (page 9) and INITIAL settings

(page 5).

1 Press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select [SYSTEM], then press to confirm.

3 Turn the M.C. dial to select [DEMO OFF], then press to confirm.

4 Turn the M.C. dial to select [YES], then press to confirm.

1 Press and hold SRC/OFF until the unit turns off.

2 Press and hold SRC/OFF to display the main menu.

3 Turn the M.C. dial to select [INITIAL], then press to confirm.

4 Turn the M.C. dial to select an option, then press to confirm.

NOTE

The options vary depending on the unit.

Canceling the demonstration display (DEMO OFF)

INITIAL settings

Menu Item Description

FM STEP Select the FM tuning step from 100 kHz or 50 kHz.

[100], [50]

SP-P/O MODE Select when there is a full-range speaker connected to the rear

speake

r output leads and there is a subwoofer connected to the

RCA output.

[REAR/SUB.W]

[SUB.W/SUB.W] Select when there is a passive subwoofer connected directly to

he rear speaker output leads and there is a subwoofer

connected to the RCA output.

[REAR/REAR] Select when there are full-range speakers connected to the rear

speake

r output leads and RCA output. If there is a full-range

speaker connected to the rear speaker output leads, and the

RCA output is not used, you may select either [REAR/SUB.W] or

[REAR/REAR].

SYSTEM RESET Select [YES] to initialize the unit settings. The unit will be

estarted automatically.

(Some of the settings may be retained even after resetting the

it.)

[YES], [CANCEL]

The tuner frequencies on this unit are allocated for use in Western Europe, Asia, the

Middle East, Africa and Oceania. Use in other areas may result in poor reception. The RDS

(radio data system) function only works in areas that broadcast RDS signals for FM

stations.

1 Press SRC/OFF to select [RADIO].

2 Press BAND/ to select the band from [FM1], [FM2], [FM3], [MW] or [LW].

3 Press a number button (1/ to 6/ ).

TIP

The / buttons can be also used to select a preset station when [SEEK] is set to [PCH] in the

FUNCTION settings (page 8).

The six strongest stations are stored on the number buttons (1/ to 6/ ).

1 After selecting the band, press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select [FUNCTION], then press to confirm.

3 Turn the M.C. dial to select [BSM], then press to confirm.

To seek a station manually

1 After selecting the band, press / to select a station.

Press and hold / then release to seek an available station. Scanning stops

when the unit receives a station. To cancel seek tuning, press / .

NOTE

[SEEK] needs to be set to [MAN] in the FUNCTION settings (page 8).

To store stations manually

1 While receiving the station you want to store, press and hold one of the number

buttons (1/ to 6/ ) until it stops flashing.

Radio

Receiving preset stations

Best stations memory (BSM)

6En

The unit searches for a station by PTY (program type) information.

1 Press during FM reception.

2 Turn the M.C. dial to select a program type from [NEWS/INFO], [POPULAR],

[CLASSICS] or [OTHERS].

3 Press the M.C. dial.

The unit begins to search for a station. When it is found, its program service name is

displa

yed.

NOTES

• To cancel the search, press the M.C. dial.

• The program of some stations may differ from that indicated by the transmitted PTY.

• If no station is broadcasting the type of program you searched for, [NOT FOUND] is displayed for

about two seconds and then the tuner returns to the original station.

PTY list

For more details about PTY list, visit the following site:

http://www.pioneer.eu/eur/products/25/121/tech/CarAudio/PTY.html

Disconnect headphones from the device before connecting it to the unit.

Using PTY functions

CD/USB/AUX

Playing back

AUX input jack (3.5 mm stereo jack)

(eject)

Disc loading slot

USB port

SRC (source)/OFF

M.C. (multi-control) dial

1 Insert a disc into the disc loading slot with the label side up.

To eject a disc, stop playback first then press .

USB devices (including Android™)

1 Open the USB port cover.

2 Plug in the USB device using an appropriate cable.

NOTE

To automatically switch to [USB] source when a USB device is connected to the unit, set [USB AUTO] to

[ON] in the SYSTEM settings (page 9).

CAUTION

Use an optional Pioneer USB cable (CD-U50E) to connect the USB device as any device connected

directly to the unit will protrude out from the unit, which could be dangerous.

Before removing the device, stop playback.

AOA connections

For details on AOA connection, see page 7.

MTP connection

A device installed with Android OS 4.0 or later can be connected to the unit via MTP, using the cable

supplied with the device. However, depending on the connected device and the numbers of the files in

the device, audio files/songs may not be able to be played back via MTP. Note that MTP connection is

not compatible with WAV and FLAC file formats.

NOTE

If you use an MTP connection, [ANDROID WIRED] needs to be set to [MEMORY] in the SYSTEM settings

(page 9).

AUX

1 Insert the stereo mini plug into the AUX input jack.

2 Press SRC/OFF to select [AUX] as the source.

NOTE

If [AUX] is set to [OFF] in the SYSTEM settings, [AUX] cannot be selected as a source (page 9).

You can make various adjustments in the FUNCTION settings (page 8).

Note that the following operations do not work for an AUX device. To operate an AUX

vice, use the device itself.

Operations

7En

English

*1 Compressed audio files only

*2 When you use the fast forward or reverse function while playing a VBR file, the playback time may

be not correct.

You can operate the unit from Pioneer ARC APP installed on an Android device. In some

cases, you can control aspects of the application, such as source selection, pause, etc., by

using the unit.

For details on what operations are available on t

he application, see the application’s help

section.

Purpose Operation

Select a folder/album*1 Press 1/ or 2/ .

Select a track/song (chapter) Press or .

Fast forward or reverse*2 Press and hold or .

Search for a file from a list 1 Press to display the list.

2 Tu

rn the M.C. dial to select the desired

file (folder) name or category, then press

to confirm.

3 Tu

rn the M.C. dial to select the desired

file, then press to confirm.

Playback starts.

View a list of the files in the selected folder/

cat

egory*1

Press the M.C. dial when a folder/category

is selected.

Play a song in the selected folder/

cat

egory*1

Press and hold the M.C. dial when a folder/

category is selected.

Repeat play Press 6/ .

Random play Press 5/ .

Pause/resume playback Press 4/PA

USE.

Sound retriever*1 Press 3/S.

Rtrv.

[1]: Effective for low compression rates

[2]: Effective for high compression rates

Return to root folder (CD/USB only)*1 Press and hold .

Switch between compressed audio and CD-

DA (

CD only)

Press BAND/ .

Change drives in USB device

(Devices that support the USB mass storage

device class protocol only)

Press BA

ND/ .

Using Pioneer ARC APP

WARNING

Do not attempt to operate the application while driving. Make sure to pull off the road and park your

vehicle in a safe location before attempting to use the controls on the application.

For Android device users

This function is compatible with devices that have Android OS 4.1 or later installed and

lso support AOA (Android Open Accessory) 2.0.

You can download Pioneer ARC APP on Google Play™.

NOTE

Some Android devices connected via AOA 2.0 may not work properly or emit sounds due to their own

software design, regardless of the OS version.

1 Connect this unit with the mobile device.

• An

droid device via USB (page 6)

2 Press the M.C. dial to display the main menu.

3 Turn the M.C. dial to select [SYSTEM], then press to confirm.

4 Turn the M.C. dial to select [ANDROID WIRED], then press to confirm.

5 Turn the M.C. dial to select [APP CONTROL] for an Android device connected via

USB.

If [ON] is selected in [P.APP AUTO ON] (page 10), Pioneer ARC APP on the Android

device starts automatically, and all the steps are finished.

NOTE

If Pioneer ARC APP has not been installed on your Android device yet, a message that prompts you

to install the application will appear on your Android device. Select [OFF] in [P.APP AUTO ON] to

clear the message (page 10).

6 Press SRC/OFF to select any source.

7 Launch Pioneer ARC APP on the mobile device.

1 Press SRC/OFF to select [ANDROID].

Making a connection with Pioneer ARC APP

Listening to music on Android

8En

Basic operations

You can adjust various settings in the main menu.

1 Press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select one of the categories below, then press to confirm.

• FUNCTION settings (page 8)

• AUDIO settings (page 8)

• SYSTEM settings (page 9)

• ILLUMINATION settings (page 10)

3 Turn the M.C. dial to select the options, then press to confirm.

The menu items vary according to the source.

Purpose Operation

Select a track Press or .

Fast forward or reverse Press and hold or .

Pause/resume playback Press 4/PA

USE.

Sound retriever Press 3/S.

Rtrv.

[1]: Effective for low compression rates

[2]: Effective for high compression rates

Settings

FUNCTION settings

Menu Item Description

FM SETTING

[TALK], [STANDARD], [MUSIC] Match the sound quality level with the broadcast

sign

al conditions of the FM band signal.

(Available only when FM band is selected.)

BSM

Store the six strongest stations on the number

but

tons (1/ to 6/ ) automatically.

REGIONAL

[ON], [OFF] Limit the reception to the specific regional

programs when AF (alternative frequencies

search) is selected. (Available only when FM

band is selected.)

LOCAL

FM: [O

FF], [LV1], [LV2], [LV3], [LV4]

MW/LW: [O

FF], [LV1], [LV2]

Restrict the tuning station according to the

sign

al strength.

[ON], [OFF] Receive current traffic information if available.

(

Available only when FM band is selected.)

[ON], [OFF] Allow the unit to retune to a different frequency

pro

viding the same station. (Available only when

FM band is selected.)

NEWS

[ON], [OFF] Interrupt the currently selected source with

news

programs. (Available only when FM band is

selected.)

SEEK

[MAN], [PCH] Assign or buttons to seek the stations

one by one (manual tuning) or select a station

rom the preset channels.

S.RTRV

[1] (effective for low compression

tes),

[2] (effective for high

mpression rates),

[OFF]

Enhance compressed audio and restore rich

und.

Not available when:

• C

D-DA/CD-TEXT is played back.

• The F

LAC file is played back.

AUDIO settings

Menu Item Description

FADER*1

Adjust the front and rear speaker balance.

Menu Item Description

USB

9En

English

*1 Not available when [SUB.W/SUB.W] is selected in [SP-P/O MODE] in the INITIAL settings (page 5).

*2 Not available when [REAR/REAR] is selected in [SP-P/O MODE] in the INITIAL settings (page 5).

*3 Not available when [OFF] is selected in [SUB.W].

BALANCE

Adjust the left and right speaker balance.

EQ SETTING

[SUPER BASS], [POWERFUL],

[NA

TURAL], [VOCAL], [CUSTOM1],

[CUSTOM2], [FLAT]

Select an equalizer band and

level for further customizing.

Equalizer band: [

80HZ], [250HZ],

[800HZ], [2.5KHZ], [8KHZ]

Equalizer level: [+

6] to [–6]

Select or customize the equalizer curve.

[CUSTOM1] can be set separately for each source.

owever, each of the below combinations are set

to the same setting automatically.

[CUSTOM2] is a shared setting used for all

urces.

You can also switch the equalizer by pressing

repeatedly.

LOUDNESS

[OFF], [LOW], [MID], [HI] Compensate for clear sound at low volume.

SUB.W*2

[NOR], [REV], [OFF] Select the subwoofer phase.

SUB.W CTRL*2

Cut-off frequency: [50H

Z],

[63HZ], [80HZ], [100HZ], [125HZ],

[160HZ], [200HZ]

Output level: [–24] t

o [+6]

Slope level: [

–12], [–24]

Only frequencies lower than those in the

selected range are output from the subwoofer.

BASS BOOST

[0] to [+6] Select the bass boost level.

HPF SETTING

Cut-off frequency: [O

FF], [50HZ],

[63HZ], [80HZ], [100HZ], [125HZ],

[160HZ], [200HZ]

Slope level: [

–12], [–24]

Only frequencies higher than the high-pass filter

(

HPF) cutoff are output from the speakers.

SLA

[+4] to [–4]

Adjust the volume level for each source except

FM.

Menu Item Description

You can also access to these menus when the unit is turned off.

SYSTEM settings

Menu Item Description

LANGUAGE

[ENG](English), [РУС](Russian),

[TUR](Turkish)

Select the language to display the text

information from a compressed audio file.

CLOCK SET

Set the clock (page 4).

12H/24H

[12H], [24H] Select the time notation.

AUTO PI

[ON], [OFF] Search for a different station with the same

pro

gramming, even if using a preset station.

AUX

[ON], [OFF] Set to [ON] when using an auxiliary device

onnected to the unit.

USB AUTO

[ON], [OFF] Select [ON] to automatically switch to [USB]

ource when a USB device is connected to the

unit.

Select [OFF] when a USB device is being

nnected to the unit just for charging.

MUTE MODE (Not a

vailable for DEH-1800UBA)

[MUTE], [20dB ATT], [10dB ATT] Mute or attenuate sound automatically when a

ignal from equipment with a mute function is

received.

PW SAVE*

(Not available for DEH-1800UBA)

[ON], [OFF] Reduce the battery power consumption.

Turning on the source is the only operation

lowed when this function is on.

ANDROID WIRED

[MEMORY], [APP CONTROL] Select the appropriate connection method for an

ndroid device.

10En

* [PW SAVE] is canceled if the vehicle battery is disconnected and will need to be turned back on once

the battery is reconnected. When [PW SAVE] is off, depending on connection methods, the unit may

continue to draw power from the battery if your vehicle’s ignition does not have an ACC (accessory)

position.

P. A P P AU TO O N

[ON], [OFF]

Select [ON] to automatically launch the car remote

application when an Android device is connected

to the unit via AOA. (Not available when

[MEMORY] is selected in [ANDROID WIRED].)

ILLUMINATION settings

Menu Item Description

DIM SETTING

[SYNC CLOCK], [MANUAL] Change the display brightness.

BRIGHTNESS

[1] to [10] Change the display brightness.

The available setting ranges differ depending on

[

DIM SETTING].

Menu Item Description

Important

• When installing this unit in a vehicle

without an ACC (accessory) position on

the ignition switch, failure to connect the

red cable to the terminal that detects

operation of the ignition key may result

in battery drain.

• Use of this unit in conditions other than

the following could result in fire or

malfunction.

–Vehicles with a 12-volt battery and

neg

ative grounding.

–When speaker output is used by 4

chan

nels, use speakers over 50 W

(maximum input power) and between 4

Ω to 8 Ω (impedance value). Do not use

1 Ω to 3 Ω speakers for this unit.

–When rear speaker output is used by 2

of subwoofer, use speakers over 70 W

(maximum input power).

* Please refer to connections for a

nnection method.

• T

o prevent a short-circuit, overheating or

malfunction, be sure to follow the

directions below.

–Disconnect the negative terminal of the

bat

tery before installation.

–Secure the wiring with cable clamps or

dhesive tape. Wrap adhesive tape

around wiring that comes into contact

with metal parts to protect the wiring.

– Place all cables away from moving parts,

ch as the shift lever and seat rails.

–Place all cables away

from hot places,

such as near the heater outlet.

–Do not connect the yellow cable to the

bat

tery by passing it through the hole

to the engine compartment.

–Cover any disconnected cable

nnectors with insulating tape.

–Do not shorten any cables.

–Never cut the insulation of the power

cabl

e of this unit in order to share the

power with other devices. The current

capacity of the cable is limited.

–Use a fuse of the rating prescribed.

–Never wire the negative speaker cable

rectly to ground.

–Never band together negative cables of

ultiple speakers.

• When t

his unit is on, control signals are

sent through the blue/white cable.

Connect this cable to the system remote

control of an external power amp or the

vehicle’s auto-antenna relay control

terminal (max. 300mA 12 V DC). If the

vehicle is equipped with a glass antenna,

connect it to the antenna booster power

supply terminal.

• Nev

er connect the blue/white cable to

the power terminal of an external power

amp. Also, never connect it to the power

terminal of the auto antenna. Doing so

may result in battery drain or a

malfunction.

• T

he black cable is ground. Ground cables

for this unit and other equipment

(especially, high-current products such as

power amps) must be wired separately. If

they are not, an accidental detachment

may result in a fire or malfunction.

• Th

e graphical symbol placed on

the product means direct current.

Connections/Installation

Connections

ACC position No ACC position

11En

English

This unit

Power cord input

Rear output or subwoofer output

Antenna input

Fuse (10 A)

Wired remote input (Not available for

DEH-1800UBA)

Hard-wired remote control adapter can

be connec

ted (sold separately).

Power cord

To power cord input

Depending on the kind of vehicle, the

function of and may be different.

In this case, be sure to connect to

and to .

Yel low

Back-up (or accessory)

Yel low

Connect to the constant 12 V supply

rminal.

Red

Accessory (or back-up)

Red

Connect to terminal controlled by the

ign

ition switch (12 V DC).

Connect leads of the same color to each

other.

Black (chassis ground)

Blue/white

The pin position of the ISO connector

ill differ depending on the type of

vehicle. Connect and when Pin 5

is an antenna control type. In another

ype of vehicle, never connect and

Blue/white

Connect to the system control terminal

the power amp (max. 300 mA 12 V

DC).

Blue/white

Connect to the auto-antenna relay

ontrol terminal (max. 300 mA 12 V DC).

Yellow/black (Not available for DEH-

1800UBA)

If you use equipment with a Mute

unction, wire this lead to the Audio

Mute lead on that equipment. If not,

keep the Audio Mute lead free of any

connections.

Speaker leads

White: Front left

White/black: Front left

Gray: Front right

Gray/black: Front right

Green: Rear left or subwoofer

Green/black: Rear left or subwoofer

Violet: Rear right or subwoofer

Violet/black: Rear right or subwoofer

ISO connector

In some vehicles, the ISO connector

y be divided into two. In this case, be

sure to connect to both connectors.

NOTES

• Change the initial menu of this unit. Refer

to [SP-P/O MODE]

(page 5). The

subwoofer output of this unit is

naural.

• W

hen using a subwoofer of 2 Ω, be sure

to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and

green/black leads.

Power amp (sold separately)

Perform these connections when using the

optional amplifier.

System remote control

Connect to blue/white cable.

Power amp (sold separately)

Connect with RCA cables (sold

separately)

To rear output or subwoofer output

Rear speaker or subwoofer

Important

• Check all connections and systems before

final installation.

• Do not use unauthorized parts as this

may cause malfunctions.

• C

onsult your dealer if installation requires

drilling of holes or other modifications to

the vehicle.

• Do

not install this unit where:

–it may interfere with operation of the

vehicl

–it may cause injury to a passenger as a

resu

lt of a sudden stop.

• T

he semiconductor laser will be damaged

if it overheats. Install this unit away from

hot places such as near the heater outlet.

• Opt

imum performance is

obtained when the unit is

installed at an angle of less

than 60°.

• W

hen installing, to ensure proper heat

dispersal when using this unit, make sure

you leave ample space behind the rear

panel and wrap any loose cables so they

are not blocking the vents.

DIN mount installation

1 Insert the supplied mounting sleeve

into the dashboard.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs

(90°) into place.

Dashboard

Mounting sleeve

• Mak

e sure that the unit is installed

securely in place. An unstable

installation may cause skipping or

other malfunctions.

When not using the supplied

mounting sleeve

1 Determine the appropriate position

where the holes on the bracket and

the side of the unit match.

Installation

Leave ample

space

5 cm

12En

2 Tighten two screws on each side.

Tapping screw (5 mm × 9 mm, not

supplied with product)

Mounting bracket

Dashboard or console

Removing the unit (installed with

the supplied mounting sleeve)

1 Remove the trim ring.

Trim ring

Notched tab

• R

eleasing the front panel allows easier

access to the trim ring.

• Wh

en reattaching the trim ring, point

the side with the notched tab down.

2 Insert the supplied extraction keys

into both sides of the unit until they

click into place.

3 Pull the unit out of the dashboard.

The display automatically returns to the

normal display.

→ No operations have been made for

about 30 seconds.

– Perform an operation.

The repeat play range changes

unexpectedly.

→ Depending on the repeat play range,

the selected range may change when

another folder or track is being selected

or during fast forwarding/reversing.

– Select the repeat play range again.

A subfolder is not played back.

→ Subfolders cannot be played when

[FLD] (folder repeat) is selected.

– Select another repeat play range.

The sound is intermittent.

→ You are using a device, such as a cellular

phone, that may cause audible

interference.

– Move electrical devices that may be

ausing the interference away from

the unit.

Common

AMP ERROR

→ This unit fails to operate or the speaker

connection is incorrect.

→ T

he protective circuit is activated.

– Check the speaker connection.

– Turn the ignition switch OFF and back

o ON again. If the message remains,

contact your dealer or an authorized

Pioneer Service Station for assistance.

NO XXXX (NO TITLE, for example)

→ There is no embedded text information.

– Switch the display or play another

ack/file.

CD player

ERROR-07, 11, 12, 17, 30

→ The disc is dirty.

–Clean the disc.

→ T

he disc is scratched.

– Replace the disc.

ERROR-07, 10, 11, 12, 15, 17, 30, A0

→ There is an electrical or mechanical

error.

– Turn the ignition switch OFF and back

ON, or switch to a different source,

then back to the CD player.

ERROR-15

→ The inserted disc is blank.

– Replace the disc.

ERROR-23

→ Unsupported CD format.

– Replace the disc.

FORMAT READ

→ Sometimes there is a delay between the

start of playback and when you start to

hear any sound.

– Wait until the message disappears and

ou hear sound.

NO AUDIO

→ The inserted disc does not contain any

playable files.

– Replace the disc.

SKIPPED

→ The inserted disc contains DRM

protected files.

– The protected files are skipped.

Additional Information

Troubleshooting

Error messages

13En

English

PROTECT

→ All the files on the inserted disc are

embedded with DRM.

– Replace the disc.

USB device

FORMAT READ

→ Sometimes there is a delay between the

start of playback and when you start to

hear any sound.

– Wait until the message disappears and

ou hear sound.

NO AUDIO

→ There are no songs.

– Transfer the audio files to the USB

vice and connect.

→ The co

nnected USB device has security

enabled.

– Follow the USB device instructions to

isable the security.

SKIPPED

→ The connected USB device contains

DRM protected files.

– The protected files are skipped.

PROTECT

→ All the files on the connected USB

device are embedded with DRM.

– Replace the USB device.

N/A USB

→ The connected USB device is not

supported by this unit.

– Disconnect your device and replace it

wit

h a compatible USB device.

HUB ERROR

→ The USB device connected via a USB

hub is not supported by this unit.

– Connect the USB device directly to this

nit using a USB cable.

CHECK USB

→ The USB connector or USB cable has

short-circuited.

–Check that the USB connector or USB

cable is

not caught in something or

damaged.

→ The co

nnected USB device consumes

more than maximum allowable current.

–Disconnect the USB device and do not

use it

. Turn the ignition switch OFF

and back to ACC or ON. Connect only

compliant USB devices.

ERROR-19

→ Communication failed.

–Perform one of the following

erations, then return to the USB

source.

• T

urn the ignition switch OFF and

back to ON.

• Di

sconnect the USB device.

• C

hange to a different source.

ERROR-23

→ USB device was not formatted properly.

–Format the USB device with FAT12,

FAT

16 or FAT32.

STOP

→ There are no songs in the current list.

–Select a list that contains songs.

Discs and player

• Use only discs that feature either of the

following two logos.

• Use 12-cm discs.

• U

se only conventional, fully circular discs.

• T

he following types of discs cannot be

used with this unit:

–DualDiscs

Handling guidelines

–8-cm discs: Attempts to use such discs

with an adaptor may cause the unit to

malfunction.

–Oddly shaped discs

–Discs other than CDs

–Damaged discs, including discs that are

cra

cked, chipped or warped

–CD-R/RW discs that have not been

nalized

• D

o not write on or apply chemicals to the

surface of the discs.

• T

o clean a CD, wipe the disc with a soft

cloth outward from the center.

• C

ondensation may temporarily impair

the player’s performance. Let it rest for

about one hour to adjust to a warmer

temperature. Also, wipe any damp discs

off with a soft cloth.

• When

using discs that can be printed on

label surfaces, check the instructions and

the warnings of the discs. Depending on

the discs, inserting and ejecting may not

be possible. Using such discs may result

in damage to this equipment.

• D

o not attach commercially available

labels or other materials to the discs.

–The discs may warp making the disc

unpl

ayable.

–The labels may come off during

play

back and prevent ejection of the

discs, which may result in damage to

the equipment.

USB storage device

• Connections via USB hubs are not

supported.

• F

irmly secure the USB storage device

before driving. Do not let the USB storage

device fall onto the floor, where it may

become jammed under the brake or

accelerator pedal.

• D

epending on the USB storage device,

the following problems may occur.

–Operations may vary.

–The storage device may not be

reco

gnized.

– Files may not be played back properly.

– The device may cause audible

int

erference when you are listening to

the radio.

• On

ly the first 32 characters can be

displayed as a file name (including the file

extension) or a folder name.

• T

he unit may not work properly

depending on the application used to

encode WMA files.

• T

here may be a slight delay at the start of

the playback of audio files embedded

with image data, or audio files stored on a

USB device with numerous folder

hierarchies.

• R

ussian text to be displayed on this unit

should be encoded in one of the

following character sets:

–Unicode (UTF-8, UTF-16)

– A character set other than Unicode that

used in a Windows environment and

is set to Russian in the multi-language

setting

CAUTION

• Pioneer cannot guarantee compatibility

with all USB mass storage devices, and

assumes no responsibility for any loss of

data on media players, smartphones, or

other devices while using this product.

• Do not leave discs or a USB storage

device in any place that is subject to high

temperatures.

WMA files

Compressed audio

compatibility

File extension .wma

Bit rate 48 kbps to 320 kbps

(CBR), 48 kbps to 384

kbps (VBR)

14En

MP3 files

WAV files

• WAV file formats cannot be connected via

MTP.

FLAC files

• FLAC file formats cannot be connected

via MTP.

• F

LAC files may not be playable,

depending on the encoder.

Disc

• Regardless of the length of the blank

section between the songs from the

original recording, compressed audio

discs play with a short pause between

songs.

USB device

• There may be a slight delay when starting

playback of audio files on a USB storage

device with numerous folder hierarchies.

The user cannot assign folder numbers and

spec

ify playback sequences with this unit.

Sequence of audio file depends on the

connected device.

Note that the hidden files in a USB device

can

not be played back.

Sampling frequency 32 kHz, 44.1 kHz, 48

kHz

Windows Media™

Audio Professional,

Lossless, Voice/DRM

Stream/Stream with

video

Not compatible

File extension .mp3

Bit rate 8 kbps to 320 kbps

(CBR), VBR

Sampling frequency 8 kHz to 48 kHz (32

kHz, 44.1 kHz, 48 kHz

for emphasis)

Compatible ID3 tag

version

1.0, 1.1, 2.2, 2.3, 2.4

(ID3 tag Version 2.x is

given priority over

Version 1.x.)

M3u playlist Not compatible

MP3i (MP3

interactive), mp3 PRO

Not compatible

File extension .wav

Quantization bits 8 and 16 (LPCM), 4

(MSADPCM)

Sampling frequency 16 kHz to 48 kHz

(LPCM), 22.05 kHz and

44.1 kHz (MS ADPCM)

File extension .flac

Sampling frequency 8/11.025/12/16/22.05/

24/32/44.1/48 kHz

Quantization bit rate 16 bit

Channel mode 1/2 ch

Playable folder

hierarchy

Up to eight tiers (A

practical hierarchy is

less than two tiers.)

Playable folders Up to 99

Playable files Up to 999

File system ISO 9660 Level 1 and

2, Romeo, Joliet

Multi-session

playback

Compatible

Packet write data

transfer

Not compatible

Playable folder

hierarchy

Up to eight tiers (A

practical hierarchy is

less than two tiers.)

Playable folders Up to 500

Playable files Up to 15 000

Playback of copyright-

protected files

Not compatible

Partitioned USB

device

Only the first partition

can be played.

Sequence of audio files

Example of a hierarchy

WMA

Windows Media is either a registered

rademark or trademark of Microsoft

Corporation in the United States and/or

other countries.

This product includes technology owned

Microsoft Corporation and cannot be

used or distributed without a license from

Microsoft Licensing, Inc.

FLAC

undation

Redistribution and use in source and

inary forms, with or without modification,

are permitted provided that the following

conditions are met:

– Redistributions of source code must

etain the above copyright notice, this list

of conditions and the following

disclaimer.

– Redistributions in binary form must

eproduce the above copyright notice,

this list of conditions and the following

disclaimer in the documentation and/or

other materials provided with the

distribution.

– Neither the name of the Xiph.org

oundation nor the names of its

contributors may be used to endorse or

promote products derived from this

software without specific prior written

permission.

THIS SOFTWARE IS PROVIDED BY THE

COP

YRIGHT HOLDERS AND

CONTRIBUTORS “AS IS” AND ANY EXPRESS

OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE

FOUNDATION OR CONTRIBUTORS BE

LIABLE FOR ANY DIRECT, INDIRECT,

Russian character chart

Folder

Compressed

audio file

to : Playback sequence

01 to 05: Folder number

D: Display C: Character

15En

English

INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL DAMAGES (INCLUDING,

BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF

USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND

ON ANY THEORY OF LIABILITY, WHETHER

IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE)

ARISING IN ANY WAY OUT OF THE USE OF

THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

Android & Google Play

Android, Google Play, and the Google Play

log

o are trademarks of Google Inc.

General

Power source: 14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system: Negative type

Maximum current consumption: 10.0 A

Dimensions (W × H × D):

DIN

Chassis: 178 mm × 50 mm × 165 mm

Nose: 188 mm × 58 mm × 17 mm

Chassis: 178 mm × 50 mm × 165 mm

Nose: 170 mm × 46 mm × 17 mm

Weight: 1 kg

Audio

Maximum power output:

• 50 W × 4 ch/4 Ω (for no subwoofer)

•

50 W × 2 ch/4 Ω + 70 W × 1 ch/2 Ω

(for subwoofer)

Continuous power output:

22 W × 4 (50 Hz to 15 000 Hz, 5 %

D, 4 Ω load, both channels driven)

Load impedance: 4 Ω (4 Ω to 8 Ω allowable)

Preout maximum output level: 2.0 V

Loudness contour: +10 dB (100 Hz), +6.5

(10 kHz) (volume: –30 dB)

Equalizer (5-Band Graphic Equalizer):

Frequency: 80 Hz/250 Hz/800 Hz/2.5

kHz

/8 kHz

Equalization range: ±12 dB (2 dB step)

Subwoofer (mono):

Frequency: 50 Hz/63 Hz/80 Hz/100

z/125 Hz/160 Hz/200 Hz

Slope: –12 dB/oct, –24 dB/oct

Gain: +6 dB to –24 dB

Phase: Normal/Reverse

CD player

System: Compact disc audio system

Usable discs: Compact disc

Signal-to-noise ratio: 94 dB (1 kHz) (IEC-A

twork)

Number of channels: 2 (stereo)

MP3 decoding format: MPEG-1 & 2 Audio

yer 3

WMA decoding format: Ver. 7, 7.1, 8, 9, 10,

11, 1

2 (2 ch audio) (Windows Media

Player)

WAV signal format: Linear PCM & MS

DPCM (Non-compressed)

USB

USB standard specification: USB 2.0 full

speed

Maximum current supply: 1 A

USB Protocol:

MSC (Mass Storage Class)

MTP (Media Transfer Protocol)

AOA (Android Open Accessory) 2.0

File system: FAT12, FAT16, FAT32

MP3 decoding format: MPEG-1 & 2 Audio

yer 3

WMA decoding format: Ver. 7, 7.1, 8, 9, 10,

11, 1

2 (2 ch audio) (Windows Media

Player)

FLAC decoding format: v1.3.0 (Free

ssless Audio Codec)

WAV signal format: Linear PCM & MS

DPCM (Non-compressed)

FM tuner

Frequency range: 87.5 MHz to 108.0 MHz

Specifications

Usable sensitivity: 11 dBf (1.0 μV/75 Ω,

mono, S/N: 30 dB)

Signal-to-noise ratio: 72 dB (IEC-A network)

MW tuner

Frequency range: 531 kHz to 1 602 kHz

Usable sensitivity: 25 μV (S/N: 20 dB)

Signal-to-noise ratio: 62 dB (IEC-A network)

LW tuner

Frequency range: 153 kHz to 281 kHz

Usable sensitivity: 28 μV (S/N: 20 dB)

Signal-to-noise ratio: 62 dB (IEC-A network)

NOTE

Specifications and the design are subject

to modifications without notice.

2Fr

Avant de commencer ............................................................................. 2

Mise en route ........................................................................................... 3

Radio.......................................................................................................... 5

CD/USB/AUX............................................................................................. 6

Utilisation de Pioneer ARC APP............................................................ 8

Réglages ................................................................................................... 8

Réglages FUNCTION ............................................................................... 9

Réglages AUDIO....................................................................................... 9

Réglages SYSTEM ................................................................................. 10

Réglages ILLUMINATION..................................................................... 11

Raccordements/Installation................................................................ 11

Informations complémentaires.......................................................... 14

À propos de ce mode d’emploi :

• Parmi les instructions suivantes, les clés USB ou les lecteurs audio USB sont

collectivement désignés sous le nom de « périphérique USB ».

Table des matières

Nous vous remercions d’avoir acheté cet appareil PIONEER

Pour garantir une utilisation correcte, lisez bien ce mode d’emploi avant d’utiliser cet appareil. Il est

particulièrement important que vous lisiez et respectiez les indications AT T E N T IO N et PRÉCAUTION

de ce mode d’emploi. Conservez-le dans un endroit sûr et facilement accessible pour toute

consultation ultérieure.

Dans les états membres de l’UE, en Suisse et en Norvège, les foyers domestiques peuvent rapporter

leurs produits électroniques usagés gratuitement à des points de collecte spécifiés ou à un revendeur

(sous réserve d’achat d’un produit similaire).

Dans les pays qui ne sont pas mentionnés ci-dessus, veuillez contacter les autorités locales pour vous

informer de la méthode correcte de mise au rebut.

En agissant ainsi vous assurerez que le produit que vous mettez au rebut est soumis au processus de

traitement, de récupération et de recyclage nécessaire et éviterez ainsi les effets négatifs potentiels sur

l’environnement et la santé publique.

ATTENTION

• N’essayez pas d’installer cet appareil ou d’en faire l’entretien vous-même. L’installation ou

l’entretien de cet appareil par des personnes sans formation et sans expérience en équipement

électronique et en accessoires automobiles peut être dangereux et vous exposer à des risques

d’électrocution ou à d’autres dangers.

• N’essayez pas de démonter ou de modifier cet appareil. Veillez à quitter la route et garer votre véhicule

en lieu sûr avant d’essayer d’utiliser les commandes de l’appareil.

PRÉCAUTION

• Ne laissez pas cet appareil entrer en contact avec de l’humidité et/ou des liquides. Cela pourrait

provoquer une décharge électrique. Tout contact avec des liquides pourrait également provoquer des

dommages, de la fumée et une surchauffe de l’appareil.

• Maintenez le niveau d’écoute à une valeur telle que vous puissiez entendre les sons provenant de

l’extérieur.

• Le Pioneer CarStereo-Pass est utilisable seulement en Allemagne.

• Ce produit est évalué sous des conditions climatiques modérées et tropicales conformément à la

norme CEI 60065 sur les Appareils audio, vidéo et appareils électroniques analogues - Exigences de

sécurité.

Avant de commencer

Si vous souhaitez vous débarrasser de cet appareil, ne le mettez pas à la poubelle avec vos ordures

ménagères. Il existe un système de collecte séparé pour les appareils électroniques usagés, qui

doivent être récupérés, traités et recyclés conformément à la législation.

3Fr

Français

Si vous rencontrez des problèmes

En cas d’anomalie, veuillez contacter votre revendeur ou le centre d’entretien agréé par PIONEER le plus

proche.

DEH-1800UB/1800UBG/1800UBA/1800UBB/1801UB

Tél éco mm an de

REMARQUE

La télécommande est fournie uniquement pour le modèle DEH-1801UB.

PRÉCAUTION

Cet appareil est un produit laser de Classe 1, classé selon l’article IEC 60825-1:2007 relatif à la Sécurité

des produits laser.

Mise en route

Fonctionnement de base

SRC (source)/OFF

Touche de retrait

Fenêtre d’affichage

Molette M.C. (multi-contrôle)

BAND/

DISP (affichage)

Opérations fréquemment utilisées

Les touches disponibles varient selon les appareils.

* Si le fil bleu/blanc de l’appareil est relié à la borne de commande du relais d’antenne automatique du

véhicule, l’antenne se déploie lorsque la source de cet appareil est mise en service. Pour rétracter

l’antenne, mettez la source hors service.

Objectif

Opération

Unité principale Té lé co m ma nd e

Mettre l’appareil sous

ension*

Appuyez sur SRC/OFF pour

mettre l’appareil sous

tension.

Appuyez longuement sur

SRC/OF

F pour mettre

l’appareil hors tension.

Appuyez sur SRC pour

mettre l’appareil sous

tension.

Appuyez longuement sur

C pour mettre l’appareil

hors tension.

Régler le volume Tournez la molette M.C.. Appuyez sur VOLUME + ou

–.

Appuyez sur MUT

E pour

couper le son de l’appareil.

Appuyez de nouveau sur

cette touche pour rétablir le

son.

Sélectionner une source Appuyez plusieurs fois sur

SRC/OF

Appuyez plusieurs fois sur

SRC.

Modifier les informations

’affichage

Appuyez plusieurs fois sur

DISP.

Appuyez plusieurs fois sur

DISP.

Revenir à l’affichage/la liste

précéd

ent(e)

Appuyez sur BAND/ . Appuyez sur / pour

sélectionner le dossier

ivant/précédent.

Revenir à l’affichage normal

à par

tir du menu

Appuyez longuement sur

BAND/ .

–

SRC (source)

VOLUME +/–

MUTE

DISP (affichage)

FUNCTION

AUDIO

4Fr

Indication de l’affichage

Retirez la face avant pour empêcher tout vol. Débranchez tous les câbles et les

périphériques branchés à la face avant et mettez l’appareil hors tension avant de le

retirer.

Important

• Évitez de soumettre la face avant à des chocs excessifs.

• Tenez la face avant à l’abri du soleil et des températures élevées.

• Stockez toujours la face avant détachée, dans un étui de protection ou un sac.

Retirez la feuille isolante avant utilisation.

Indication Description

Apparaît lorsqu’il existe un niveau inférieur de menu ou de dossier.

Apparaît lorsque vous appuyez sur la touche .

Apparaît lorsque la fonction d’accord sur une station locale est en service

(page 9).

Apparaît lorsqu’un programme d’informations routières est capté.

Apparaît lorsque la fonction TA (informations routières) est activée

(page 9).

Apparaît lorsque le sound retriever (correcteur de son compressé) est en

rvice (page 9).

Apparaît lorsque la lecture aléatoire est en service.

Apparaît lorsque la lecture répétée est en service.

Retrait de la face avant

Préparation de la télécommande

Retirer Fixer

ATTENTION

• Ne pas ingérer la pile, risque de brûlure chimique.

• Ce produit, y compris la télécommande fournie, comprend une pile bouton. Si vous avalez la pile

bouton, de graves brûlures internes peuvent survenir en seulement deux heures, pouvant conduire à

la mort.

• Ne laissez pas les nouvelles piles ou les piles usagées à la portée des enfants. Si vous avalez la pile,

veuillez immédiatement consulter un médecin.

• Si le compartiment des piles ne se referme pas correctement, veuillez ne plus utiliser le produit et

tenez-le hors de la portée des enfants.

• N’exposez pas la pile ou la télécommande à une chaleur excessive, par exemple en plein soleil ou au

feu.

PRÉCAUTION

• Il existe un risque potentiel d’explosion si la pile est remplacée de façon incorrecte. Remplacez la pile

usagée par une pile neuve de même type.

• Ne manipulez et ne stockez pas la pile avec des outils ou des objets métalliques.

• Si la pile fuit, retirez-la et essuyez complètement la télécommande. Insérez ensuite une nouvelle pile.

• Lors de la mise au rebut des piles usagées, veuillez respecter les réglementations gouvernementales

ou les règles des institutions environnementales en vigueur dans votre pays/région.

Important

• Ne stockez pas la télécommande à des températures élevées ou en plein soleil.

• Ne laissez pas la télécommande tomber au sol, où elle pourrait rester coincée sous la pédale de frein

ou d’accélérateur.

Lorsque vous mettez le contact sur ON après avoir installé l’appareil, [SET UP :YES]

s’affiche.

1 Appuyez sur la molette M.C..

Si vous n’utilisez pas l’appareil dans les 30 secondes qui suivent, le menu de

onfiguration disparaît. Si vous préférez ne pas effectuer la configuration pour

l’instant, tournez la molette M.C. pour sélectionner [NO], puis appuyez pour valider.

Menu de configuration

Comment remplacer la pile

Insérez la pile CR2025 (3 V) en orientant

correctement les pôles plus (+) et moins (-).

5Fr

Français

2 Tournez la molette M.C. pour sélectionner les options, puis appuyez pour valider.

Pour passer à l’option de menu suivante, vous devez valider votre sélection.

3 [QUIT :YES] apparaît lorsque tous les réglages sont terminés.

Pour revenir au premier élément du menu de configuration, tournez la molette M.C

pour sélectionner [QUIT :NO], puis appuyez pour valider.

4 Appuyez sur la molette M.C. pour valider les réglages.

REMARQUES

• Vous pouvez annuler le réglage du menu en appuyant sur SRC/OFF.

• Ces paramètres peuvent être ajustés à tout moment à partir des réglages SYSTEM (page 10) et des

réglages INITIAL (page 5).

1 Appuyez sur la molette M.C. pour afficher le menu principal.

2 Tournez la molette M.C. pour sélectionner [SYSTEM], puis appuyez pour valider.

3 Tournez la molette M.C. pour sélectionner [DEMO OFF], puis appuyez pour

valider.

4 Tournez la molette M.C. pour sélectionner [YES], puis appuyez pour valider.

1 Appuyez longuement sur SRC/OFF jusqu’à ce que l’appareil se mette hors

tension.

2 Appuyez longuement sur SRC/OFF pour afficher le menu principal.

3 Tournez la molette M.C. pour sélectionner [INITIAL], puis appuyez pour valider.

Élément de menu Description

LANGUAGE Sélectionnez la langue d’affichage des informations textuelles à

par

tir d’un fichier audio compressé.

[ENG] (anglais),

[РУС

] (russe),

[TU

R] (turc)

CLOCK SET Réglez l’horloge.

FM STEP Sélectionnez l’incrément d’accord FM à partir de 100 kHz ou de

50 kHz.

[100], [50]

Annulation de l’affichage de démonstration (DEMO

OFF)

Réglages INITIAL

4 Tournez la molette M.C. pour sélectionner une option, puis appuyez pour valider.

REMARQUE

Les options varient selon les appareils.

Les fréquences du syntoniseur de cet appareil sont destinées à une utilisation en Europe

de l’Ouest, Asie, Moyen-Orient, Afrique et Océanie. Son utilisation dans d’autres régions

peut se traduire par une réception de mauvaise qualité. La fonction RDS (Radio Data

System) n’est opérationnelle que dans les régions où des signaux RDS sont diffusés pour

les stations FM.

1 Appuyez sur SRC/OFF pour sélectionner [RADIO].

2 Appuyez sur BAND/ pour sélectionner la bande [FM1], [FM2], [FM3], [MW] ou

[LW].

3 Appuyez sur l’une des touches numériques (1/ à 6/ ).

Élément de menu Description

FM STEP Sélectionnez l’incrément d’accord FM à partir de 100 kHz ou de

50 kHz.

[100], [50]

SP-P/O MODE À sélectionner lorsqu’un haut-parleur à gamme étendue est

elié aux fils de sortie du haut-parleur arrière et qu’un haut-

parleur d’extrêmes graves est branché à la sortie RCA.

[REAR/SUB.W]

[SUB.W/SUB.W] À sélectionner lorsqu’un haut-parl

eur d’extrêmes graves passif

est directement relié aux fils de sortie du haut-parleur arrière et

qu’un haut-parleur d’extrêmes graves est branché à la sortie

RCA.

[REAR/REAR] À sélectionner lorsque des haut-parleurs à gamme étendue sont

eliés aux fils de sortie du haut-parleur arrière et à la sortie RCA.

Si un haut-parleur à gamme étendue est relié aux fils de sortie

du haut-parleur arrière et que la sortie RCA n’est pas utilisée,

vous pouvez sélectionner [REAR/SUB.W] ou [REAR/REAR].

SYSTEM RESET Sélectionnez [YES] pour réinitialiser les réglages de l’appareil.

’appareil redémarre automatiquement.

(Certains réglages sont conservés même après la réinitialisation

e l’appareil.)

[YES], [CANCEL]

Radio

Réception des stations présélectionnées

6Fr

CONSEIL

Les touches / peuvent également servir à sélectionner une station préréglée lorsque [SEEK]

est réglé sur [PCH] dans les réglages FUNCTION (page 9).

Les six stations les plus puissantes sont mémorisées sur les touches numériques (1/ à

6/ ).

1 Après avoir sélectionné la bande, appuyez sur la molette M.C. pour afficher le

menu principal.

2 Tournez la molette M.C. pour sélectionner [FUNCTION], puis appuyez pour

valider.

3 Tournez la molette M.C. pour sélectionner [BSM], puis appuyez pour valider.

Pour rechercher une station manuellement

1 Après avoir sélectionné la bande, appuyez sur / pour sélectionner une

station.

Appuyez longuement sur / , puis relâchez pour rechercher une station

disponible. Le balayage s’arrête lorsque l’appareil capte une station. Pour annuler

l’

accord par recherche, appuyez sur / .

REMARQUE

[SEEK] doit être réglé sur [MAN] dans les réglages FUNCTION (page 9).

Pour mémoriser des stations manuellement

1 Lorsque vous captez la station que vous souhaitez mémoriser, appuyez

longuement sur l’une des touches numériques (1/ à 6/ ) jusqu’à ce qu’elle

cesse de clignoter.

L’appareil recherche une station diffusant des informations PTY (type de programme).

1 Appuyez sur pendant la réception FM.

2 Tournez la molette M.C. pour sélectionner le type de programme [NEWS/INFO],

[POPULAR], [CLASSICS] ou [OTHERS].

3 Appuyez sur la molette M.C..

Mémoire des meilleures stations (BSM)

Utilisation des fonctions PTY

L’appareil continue à rechercher une station. Lorsqu’il en trouve une, son nom de

service de programme s’affiche.

REMARQUES

• Pour annuler la recherche, appuyez sur la molette M.C..

• Le programme de certaines stations peut différer de celui qu’indique le PTY transmis.

• Si aucune station ne diffuse le type de programme que vous recherchez, [NOT FOUND] s’affiche

pendant environ deux secondes, puis le syntoniseur revient à la station de départ.

Liste des PTY

Pour plus de détails sur la liste des PTY, visitez le site Web suivant :

http://www.pioneer.eu/eur/products/25/121/tech/CarAudio/PTY.html

Débranchez le casque ou les écouteurs du périphérique avant de raccorder ce dernier à

’appareil.

1 Insérez un disque dans la fente de chargement des disques en orientant l’étiquette

vers le haut.

Pour éjecter un disque, arrêtez d’abord la lecture avant d’appuyer sur .

CD/USB/AUX

Lecture

Prise d’entrée AUX (prise stéréo 3,5 mm)

(éjection)

Fente de chargement des disques

Port USB

SRC (source)/OFF

Molette M.C. (multi-contrôle)

Страница загружается ...

Pioneer DEH-1800UB Руководство пользователя

Бренд: Pioneer

Модель: DEH-1800UB

Категория: Мультимедиа-приемники для автомобилей

Тип: Руководство пользователя

Это руководство также подходит для

Скачать PDF

сообщить о нарушении

на других языках

English: Pioneer DEH-1800UB User manual
français: Pioneer DEH-1800UB Manuel utilisateur
italiano: Pioneer DEH-1800UB Manuale utente
español: Pioneer DEH-1800UB Manual de usuario
Deutsch: Pioneer DEH-1800UB Benutzerhandbuch
Nederlands: Pioneer DEH-1800UB Handleiding

Pioneer DEH-1800UB Руководство пользователя

Это руководство также подходит для

Pioneer DEH-1800UB Руководство пользователя

на других языках

Похожие модели бренда